- A couple of changes to improve the support for erase/discard/trim cmds
- Add eMMC HS400 enhanced strobe support
- Show OCR and DSR registers in SYSFS for MMC/SD cards
- Correct and improve busy detection logic for MMC switch (CMD6) cmds
- Disable HPI cmds for certain broken Hynix eMMC cards
- Allow MMC hosts to specify non-support for SD and MMC cmds
- Some minor additional fixes
MMC host:
- sdhci: Re-works, fixes and clean-ups
- sdhci: Add HW auto re-tuning support
- sdhci: Re-factor code to prepare for adding support for eMMC CMDQ
- sdhci-esdhc-imx: Fixes and clean-ups
- sdhci-esdhc-imx: Update system PM support
- sdhci-esdhc-imx: Enable HW auto re-tuning
- sdhci-bcm2835: Remove driver as sdhci-iproc is used instead
- sdhci-brcmstb: Add new driver for Broadcom BRCMSTB SoCs
- sdhci-msm: Add support for UHS cards
- sdhci-tegra: Improve support for UHS cards
- sdhci-of-arasan: Update phy support for Rockchip SoCs
- sdhci-of-arasan: Deploy enhanced strobe support
- dw_mmc: Some fixes and clean-ups
- dw_mmc: Enable support for erase/discard/trim cmds
- dw_mmc: Enable CMD23 support
- mediatek: Some fixes related to the eMMC HS400 support
- sh_mmcif: Improve support for HW busy detection
- rtsx_pci: Enable support for erase/discard/trim cmds
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXnibNAAoJEP4mhCVzWIwpKIQQAM2iTx5ROuOe3/CmWEAv5phg
XpgmuWz/R/KQH1wyDor4zEJUE5mUYpvSg9vSCByYnVwHpoNKg4R0t0OJZJSN05Z0
njdKCtkVXlRaQitX3tiFQazkMLaQER0tRrqrHjYZYkBgr8DnSEf00aueSGshrr/p
g/JE7Z+eGVJx6d3Lvd24NMVZYSGbVq5lY/JTbURkKR5C9OhEe5GMfUsw1M+aVhUo
pvxeGVYuIr4WsP+c+roa6czTO8VMrsd71syLDCweWMk+GOHvaSjpzvdC7iFGAl4B
CoN6f3LTpJGpDCBWnqp/yQMvrMsR1SKlrwOUph4XEAXZCaz5WtF8+vhQaK7gwYGO
RiyIIh04Bup+gzY6w0Mwgsw0jAkw5ahXl6xknD58q/sPEdlKe0ATyxl0oUwDntc0
957BtmOvChYG13Q5pW6VNef0jKW6LOU+brJKEGxtr8x9OPeCiQOBO/GCUTg3IwA5
ohylmjS+/6G3G4bgGvfXyGvObOsdAh3RQ8g7/1pVb0hQobDhxO5PjtTqVtelfFJk
PRdKKIWhROiNMrpVLZnL7+OLkusEQ4s0Lmq08T1dVXvV+hLITwyTyWYmBr6Kb51B
2x3DO7PcfEyytSn3TjPjdp7Wax+19YL+tMmu2QAlXv3iHSKFAH17nLk0bPO6VOWZ
FHzKKutm4TwZJ/fyyiqP
=wzSC
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.8' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- A couple of changes to improve the support for erase/discard/trim cmds
- Add eMMC HS400 enhanced strobe support
- Show OCR and DSR registers in SYSFS for MMC/SD cards
- Correct and improve busy detection logic for MMC switch (CMD6) cmds
- Disable HPI cmds for certain broken Hynix eMMC cards
- Allow MMC hosts to specify non-support for SD and MMC cmds
- Some minor additional fixes
MMC host:
- sdhci: Re-works, fixes and clean-ups
- sdhci: Add HW auto re-tuning support
- sdhci: Re-factor code to prepare for adding support for eMMC CMDQ
- sdhci-esdhc-imx: Fixes and clean-ups
- sdhci-esdhc-imx: Update system PM support
- sdhci-esdhc-imx: Enable HW auto re-tuning
- sdhci-bcm2835: Remove driver as sdhci-iproc is used instead
- sdhci-brcmstb: Add new driver for Broadcom BRCMSTB SoCs
- sdhci-msm: Add support for UHS cards
- sdhci-tegra: Improve support for UHS cards
- sdhci-of-arasan: Update phy support for Rockchip SoCs
- sdhci-of-arasan: Deploy enhanced strobe support
- dw_mmc: Some fixes and clean-ups
- dw_mmc: Enable support for erase/discard/trim cmds
- dw_mmc: Enable CMD23 support
- mediatek: Some fixes related to the eMMC HS400 support
- sh_mmcif: Improve support for HW busy detection
- rtsx_pci: Enable support for erase/discard/trim cmds"
* tag 'mmc-v4.8' of git://git.linaro.org/people/ulf.hansson/mmc: (135 commits)
mmc: rtsx_pci: Remove deprecated create_singlethread_workqueue
mmc: rtsx_pci: Enable MMC_CAP_ERASE to allow erase/discard/trim requests
mmc: rtsx_pci: Use the provided busy timeout from the mmc core
mmc: sdhci-pltfm: Drop define for SDHCI_PLTFM_PMOPS
mmc: sdhci-pltfm: Convert to use the SET_SYSTEM_SLEEP_PM_OPS
mmc: sdhci-pltfm: Make sdhci_pltfm_suspend|resume() static
mmc: sdhci-esdhc-imx: Use common sdhci_suspend|resume_host()
mmc: sdhci-esdhc-imx: Assign system PM ops within #ifdef CONFIG_PM_SLEEP
mmc: sdhci-sirf: Remove non needed #ifdef CONFIG_PM* for dev_pm_ops
mmc: sdhci-s3c: Remove non needed #ifdef CONFIG_PM for dev_pm_ops
mmc: sdhci-pxav3: Remove non needed #ifdef CONFIG_PM for dev_pm_ops
mmc: sdhci-of-esdhc: Simplify code by using SIMPLE_DEV_PM_OPS
mmc: sdhci-acpi: Simplify code by using SET_SYSTEM_SLEEP_PM_OPS
mmc: sdhci-pci-core: Simplify code by using SET_SYSTEM_SLEEP_PM_OPS
mmc: Change the max discard sectors and erase response when HW busy detect
phy: rockchip-emmc: Wait even longer for the DLL to lock
phy: rockchip-emmc: Be tolerant to card clock of 0 in power on
mmc: sdhci-of-arasan: Revert: Always power the PHY off/on when clock changes
mmc: sdhci-msm: Add support for UHS cards
mmc: sdhci-msm: Add set_uhs_signaling() implementation
...
Pull watchdog updates from Wim Van Sebroeck:
"Core:
- min and max timeout improvements, WDOG_HW_RUNNING improvements,
status funtionality
- Add a device managed API for watchdog_register_device()
New watchdog drivers:
- Aspeed SoCs
- Maxim PMIC MAX77620
- Amlogic Meson GXBB SoC
Enhancements:
- support for the r8a7796 watchdog device
- support for F81866 watchdog device
- support for 5th variation of Apollo Lake
- support for MCP78S chipset
- clean-up of softdog.c watchdog device driver
- pic32-wdt and pic32-dmt fixes
- Documentation/watchdog: watchdog-test improvements
- several other fixes and improvements"
* git://www.linux-watchdog.org/linux-watchdog: (50 commits)
watchdog: gpio_wdt: Fix missing platform_set_drvdata() in gpio_wdt_probe()
watchdog: core: Clear WDOG_HW_RUNNING before calling the stop function
watchdog: core: Fix error handling of watchdog_dev_init()
watchdog: pic32-wdt: Fix return value check in pic32_wdt_drv_probe()
watchdog: pic32-dmt: Remove .owner field for driver
watchdog: pic32-wdt: Remove .owner field for driver
watchdog: renesas-wdt: Add support for the r8a7796 wdt
Documentation/watchdog: check return value for magic close
watchdog: sbsa: Drop status function
watchdog: Implement status function in watchdog core
watchdog: tangox: Set max_hw_heartbeat_ms instead of max_timeout
watchdog: change watchdog_need_worker logic
watchdog: add support for MCP78S chipset in nv_tco
watchdog: bcm2835_wdt: remove redundant ->set_timeout callback
watchdog: bcm2835_wdt: constify _ops and _info structures
dt-bindings: watchdog: Add Meson GXBB Watchdog bindings
watchdog: Add Meson GXBB Watchdog Driver
watchdog: qcom: configure BARK time in addition to BITE time
watchdog: qcom: add option for standalone watchdog not in timer block
watchdog: qcom: update device tree bindings
...
Majority of this update is about ASoC, including a few new drivers,
and the rest are mostly minor changes. The only substantial change in
ALSA core is about the additional error handling in the
compress-offload API. Below are highlights:
- Add the error propagating support in compress-offload API
- HD-audio: a usual Dell headset fixup, an Intel HDMI/DP fix, and the
default mixer setup change ot turn off the loopback
- Lots of updates for ASoC Intel drivers, mostly board support and bug
fixing, and to the NAU8825 driver
- Work on generalizing bits of simple-card to allow more code sharing
with the Renesas rsrc-card (which can't use simple-card due to DPCM)
- Removal of the Odroid X2 driver due to replacement with simple-card
- Support for several new Mediatek platforms and associated boards
- New ASoC drivers for Allwinner A10, Analog Devices ADAU7002, Broadcom
Cygnus, Cirrus Logic CS35L33 and CS53L30, Maxim MAX8960 and MAX98504,
Realtek RT5514 and Wolfson WM8758
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=zx3K
-----END PGP SIGNATURE-----
Merge tag 'sound-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"The majority of this update is about ASoC, including a few new
drivers, and the rest are mostly minor changes. The only substantial
change in ALSA core is about the additional error handling in the
compress-offload API. Below are highlights:
- Add the error propagating support in compress-offload API
- HD-audio: a usual Dell headset fixup, an Intel HDMI/DP fix, and the
default mixer setup change ot turn off the loopback
- Lots of updates for ASoC Intel drivers, mostly board support and
bug fixing, and to the NAU8825 driver
- Work on generalizing bits of simple-card to allow more code sharing
with the Renesas rsrc-card (which can't use simple-card due to DPCM)
- Removal of the Odroid X2 driver due to replacement with simple-card
- Support for several new Mediatek platforms and associated boards
- New ASoC drivers for Allwinner A10, Analog Devices ADAU7002,
Broadcom Cygnus, Cirrus Logic CS35L33 and CS53L30, Maxim MAX8960
and MAX98504, Realtek RT5514 and Wolfson WM8758"
* tag 'sound-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (278 commits)
sound: oss: Use kernel_read_file_from_path() for mod_firmware_load()
ASoC: Intel: Skylake: Delete an unnecessary check before the function call "release_firmware"
ASoC: Intel: Skylake: Fix NULL Pointer exception in dynamic_debug.
ASoC: samsung: Specify DMA channels through struct snd_dmaengine_pcm_config
ASoC: samsung: Fix error paths in the I2S driver's probe()
ASoC: cs53l30: Fix bit shift issue of TDM mode
ASoC: cs53l30: Fix a bug for TDM slot location validation
ASoC: rockchip: correct the spdif clk
ALSA: echoaudio: purge contradictions between dimension matrix members and total number of members
ASoC: rsrc-card: use asoc_simple_card_parse_card_name()
ASoC: rsrc-card: use asoc_simple_dai instead of rsrc_card_dai
ASoC: rsrc-card: use asoc_simple_card_parse_dailink_name()
ASoC: simple-card: use asoc_simple_card_parse_card_name()
ASoC: simple-card-utils: add asoc_simple_card_parse_card_name()
ASoC: simple-card: use asoc_simple_card_parse_dailink_name()
ASoC: simple-card-utils: add asoc_simple_card_set_dailink_name()
ASoC: nau8825: drop redundant idiom when converting integer to boolean
ASoC: nau8825: jack connection decision with different insertion logic
ASoC: mediatek: Add HDMI dai-links to the mt8173-rt5650 machine driver
ASoC: mediatek: mt2701: fix non static symbol warning
...
Highlights:
- PowerNV PCI hotplug support.
- Lots more Power9 support.
- eBPF JIT support on ppc64le.
- Lots of cxl updates.
- Boot code consolidation.
Bug fixes:
- Fix spin_unlock_wait() from Boqun Feng
- Fix stack pointer corruption in __tm_recheckpoint() from Michael Neuling
- Fix multiple bugs in memory_hotplug_max() from Bharata B Rao
- mm: Ensure "special" zones are empty from Oliver O'Halloran
- ftrace: Separate the heuristics for checking call sites from Michael Ellerman
- modules: Never restore r2 for a mprofile-kernel style mcount() call from Michael Ellerman
- Fix endianness when reading TCEs from Alexey Kardashevskiy
- start rtasd before PCI probing from Greg Kurz
- PCI: rpaphp: Fix slot registration for multiple slots under a PHB from Tyrel Datwyler
- powerpc/mm: Add memory barrier in __hugepte_alloc() from Sukadev Bhattiprolu
Cleanups & fixes:
- Drop support for MPIC in pseries from Rashmica Gupta
- Define and use PPC64_ELF_ABI_v2/v1 from Michael Ellerman
- Remove unused symbols in asm-offsets.c from Rashmica Gupta
- Fix SRIOV not building without EEH enabled from Russell Currey
- Remove kretprobe_trampoline_holder. from Thiago Jung Bauermann
- Reduce log level of PCI I/O space warning from Benjamin Herrenschmidt
- Add array bounds checking to crash_shutdown_handlers from Suraj Jitindar Singh
- Avoid -maltivec when using clang integrated assembler from Anton Blanchard
- Fix array overrun in ppc_rtas() syscall from Andrew Donnellan
- Fix error return value in cmm_mem_going_offline() from Rasmus Villemoes
- export cpu_to_core_id() from Mauricio Faria de Oliveira
- Remove old symbols from defconfigs from Andrew Donnellan
- Update obsolete comments in setup_32.c about entry conditions from Benjamin Herrenschmidt
- Add comment explaining the purpose of setup_kdump_trampoline() from Benjamin Herrenschmidt
- Merge the RELOCATABLE config entries for ppc32 and ppc64 from Kevin Hao
- Remove RELOCATABLE_PPC32 from Kevin Hao
- Fix .long's in tlb-radix.c to more meaningful from Balbir Singh
Minor cleanups & fixes:
- Andrew Donnellan, Anna-Maria Gleixner, Anton Blanchard, Benjamin
Herrenschmidt, Bharata B Rao, Christophe Leroy, Colin Ian King, Geliang
Tang, Greg Kurz, Madhavan Srinivasan, Michael Ellerman, Michael Ellerman,
Stephen Rothwell, Stewart Smith.
Freescale updates from Scott:
- "Highlights include more 8xx optimizations, device tree updates,
and MVME7100 support."
PowerNV PCI hotplug from Gavin Shan:
- PCI: Add pcibios_setup_bridge()
- Override pcibios_setup_bridge()
- Remove PCI_RESET_DELAY_US
- Move pnv_pci_ioda_setup_opal_tce_kill() around
- Increase PE# capacity
- Allocate PE# in reverse order
- Create PEs in pcibios_setup_bridge()
- Setup PE for root bus
- Extend PCI bridge resources
- Make pnv_ioda_deconfigure_pe() visible
- Dynamically release PE
- Update bridge windows on PCI plug
- Delay populating pdn
- Support PCI slot ID
- Use PCI slot reset infrastructure
- Introduce pnv_pci_get_slot_id()
- Functions to get/set PCI slot state
- PCI/hotplug: PowerPC PowerNV PCI hotplug driver
- Print correct PHB type names
Power9 idle support from Shreyas B. Prabhu:
- set power_save func after the idle states are initialized
- Use PNV_THREAD_WINKLE macro while requesting for winkle
- make hypervisor state restore a function
- Rename idle_power7.S to idle_book3s.S
- Rename reusable idle functions to hardware agnostic names
- Make pnv_powersave_common more generic
- abstraction for saving SPRs before entering deep idle states
- Add platform support for stop instruction
- cpuidle/powernv: Use CPUIDLE_STATE_MAX instead of MAX_POWERNV_IDLE_STATES
- cpuidle/powernv: cleanup cpuidle-powernv.c
- cpuidle/powernv: Add support for POWER ISA v3 idle states
- Use deepest stop state when cpu is offlined
Power9 PMU from Madhavan Srinivasan:
- factor out power8 pmu macros and defines
- factor out power8 pmu functions
- factor out power8 __init_pmu code
- Add power9 event list macros for generic and cache events
- Power9 PMU support
- Export Power9 generic and cache events to sysfs
Power9 preliminary interrupt & PCI support from Benjamin Herrenschmidt:
- Add XICS emulation APIs
- Move a few exception common handlers to make room
- Add support for HV virtualization interrupts
- Add mechanism to force a replay of interrupts
- Add ICP OPAL backend
- Discover IODA3 PHBs
- pci: Remove obsolete SW invalidate
- opal: Add real mode call wrappers
- Rename TCE invalidation calls
- Remove SWINV constants and obsolete TCE code
- Rework accessing the TCE invalidate register
- Fallback to OPAL for TCE invalidations
- Use the device-tree to get available range of M64's
- Check status of a PHB before using it
- pci: Don't try to allocate resources that will be reassigned
Other Power9:
- Send SIGBUS on unaligned copy and paste from Chris Smart
- Large Decrementer support from Oliver O'Halloran
- Load Monitor Register Support from Jack Miller
Performance improvements from Anton Blanchard:
- Avoid load hit store in __giveup_fpu() and __giveup_altivec()
- Avoid load hit store in setup_sigcontext()
- Remove assembly versions of strcpy, strcat, strlen and strcmp
- Align hot loops of some string functions
eBPF JIT from Naveen N. Rao:
- Fix/enhance 32-bit Load Immediate implementation
- Optimize 64-bit Immediate loads
- Introduce rotate immediate instructions
- A few cleanups
- Isolate classic BPF JIT specifics into a separate header
- Implement JIT compiler for extended BPF
Operator Panel driver from Suraj Jitindar Singh:
- devicetree/bindings: Add binding for operator panel on FSP machines
- Add inline function to get rc from an ASYNC_COMP opal_msg
- Add driver for operator panel on FSP machines
Sparse fixes from Daniel Axtens:
- make some things static
- Introduce asm-prototypes.h
- Include headers containing prototypes
- Use #ifdef __BIG_ENDIAN__ #else for REG_BYTE
- kvm: Clarify __user annotations
- Pass endianness to sparse
- Make ppc_md.{halt, restart} __noreturn
MM fixes & cleanups from Aneesh Kumar K.V:
- radix: Update LPCR HR bit as per ISA
- use _raw variant of page table accessors
- Compile out radix related functions if RADIX_MMU is disabled
- Clear top 16 bits of va only on older cpus
- Print formation regarding the the MMU mode
- hash: Update SDR1 size encoding as documented in ISA 3.0
- radix: Update PID switch sequence
- radix: Update machine call back to support new HCALL.
- radix: Add LPID based tlb flush helpers
- radix: Add a kernel command line to disable radix
- Cleanup LPCR defines
Boot code consolidation from Benjamin Herrenschmidt:
- Move epapr_paravirt_early_init() to early_init_devtree()
- cell: Don't use flat device-tree after boot
- ge_imp3a: Don't use the flat device-tree after boot
- mpc85xx_ds: Don't use the flat device-tree after boot
- mpc85xx_rdb: Don't use the flat device-tree after boot
- Don't test for machine type in rtas_initialize()
- Don't test for machine type in smp_setup_cpu_maps()
- dt: Add of_device_compatible_match()
- Factor do_feature_fixup calls
- Move 64-bit feature fixup earlier
- Move 64-bit memory reserves to setup_arch()
- Use a cachable DART
- Move FW feature probing out of pseries probe()
- Put exception configuration in a common place
- Remove early allocation of the SMU command buffer
- Move MMU backend selection out of platform code
- pasemi: Remove IOBMAP allocation from platform probe()
- mm/hash: Don't use machine_is() early during boot
- Don't test for machine type to detect HEA special case
- pmac: Remove spurrious machine type test
- Move hash table ops to a separate structure
- Ensure that ppc_md is empty before probing for machine type
- Move 64-bit probe_machine() to later in the boot process
- Move 32-bit probe() machine to later in the boot process
- Get rid of ppc_md.init_early()
- Move the boot time info banner to a separate function
- Move setting of {i,d}cache_bsize to initialize_cache_info()
- Move the content of setup_system() to setup_arch()
- Move cache info inits to a separate function
- Re-order the call to smp_setup_cpu_maps()
- Re-order setup_panic()
- Make a few boot functions __init
- Merge 32-bit and 64-bit setup_arch()
Other new features:
- tty/hvc: Use IRQF_SHARED for OPAL hvc consoles from Sam Mendoza-Jonas
- tty/hvc: Use opal irqchip interface if available from Sam Mendoza-Jonas
- powerpc: Add module autoloading based on CPU features from Alastair D'Silva
- crypto: vmx - Convert to CPU feature based module autoloading from Alastair D'Silva
- Wake up kopald polling thread before waiting for events from Benjamin Herrenschmidt
- xmon: Dump ISA 2.06 SPRs from Michael Ellerman
- xmon: Dump ISA 2.07 SPRs from Michael Ellerman
- Add a parameter to disable 1TB segs from Oliver O'Halloran
- powerpc/boot: Add OPAL console to epapr wrappers from Oliver O'Halloran
- Assign fixed PHB number based on device-tree properties from Guilherme G. Piccoli
- pseries: Add pseries hotplug workqueue from John Allen
- pseries: Add support for hotplug interrupt source from John Allen
- pseries: Use kernel hotplug queue for PowerVM hotplug events from John Allen
- pseries: Move property cloning into its own routine from Nathan Fontenot
- pseries: Dynamic add entires to associativity lookup array from Nathan Fontenot
- pseries: Auto-online hotplugged memory from Nathan Fontenot
- pseries: Remove call to memblock_add() from Nathan Fontenot
cxl:
- Add set and get private data to context struct from Michael Neuling
- make base more explicitly non-modular from Paul Gortmaker
- Use for_each_compatible_node() macro from Wei Yongjun
- Frederic Barrat
- Abstract the differences between the PSL and XSL
- Make vPHB device node match adapter's
- Philippe Bergheaud
- Add mechanism for delivering AFU driver specific events
- Ignore CAPI adapters misplaced in switched slots
- Refine slice error debug messages
- Andrew Donnellan
- static-ify variables to fix sparse warnings
- PCI/hotplug: pnv_php: export symbols and move struct types needed by cxl
- PCI/hotplug: pnv_php: handle OPAL_PCI_SLOT_OFFLINE power state
- Add cxl_check_and_switch_mode() API to switch bi-modal cards
- remove dead Kconfig options
- fix potential NULL dereference in free_adapter()
- Ian Munsie
- Update process element after allocating interrupts
- Add support for CAPP DMA mode
- Fix allowing bogus AFU descriptors with 0 maximum processes
- Fix allocating a minimum of 2 pages for the SPA
- Fix bug where AFU disable operation had no effect
- Workaround XSL bug that does not clear the RA bit after a reset
- Fix NULL pointer dereference on kernel contexts with no AFU interrupts
- powerpc/powernv: Split cxl code out into a separate file
- Add cxl_slot_is_supported API
- Enable bus mastering for devices using CAPP DMA mode
- Move cxl_afu_get / cxl_afu_put to base
- Allow a default context to be associated with an external pci_dev
- Do not create vPHB if there are no AFU configuration records
- powerpc/powernv: Add support for the cxl kernel api on the real phb
- Add support for using the kernel API with a real PHB
- Add kernel APIs to get & set the max irqs per context
- Add preliminary workaround for CX4 interrupt limitation
- Add support for interrupts on the Mellanox CX4
- Workaround PE=0 hardware limitation in Mellanox CX4
- powerpc/powernv: Fix pci-cxl.c build when CONFIG_MODULES=n
selftests:
- Test unaligned copy and paste from Chris Smart
- Load Monitor Register Tests from Jack Miller
- Cyril Bur
- exec() with suspended transaction
- Use signed long to read perf_event_paranoid
- Fix usage message in context_switch
- Fix generation of vector instructions/types in context_switch
- Michael Ellerman
- Use "Delta" rather than "Error" in normal output
- Import Anton's mmap & futex micro benchmarks
- Add a test for PROT_SAO
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Z5kM
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- PowerNV PCI hotplug support.
- Lots more Power9 support.
- eBPF JIT support on ppc64le.
- Lots of cxl updates.
- Boot code consolidation.
Bug fixes:
- Fix spin_unlock_wait() from Boqun Feng
- Fix stack pointer corruption in __tm_recheckpoint() from Michael
Neuling
- Fix multiple bugs in memory_hotplug_max() from Bharata B Rao
- mm: Ensure "special" zones are empty from Oliver O'Halloran
- ftrace: Separate the heuristics for checking call sites from
Michael Ellerman
- modules: Never restore r2 for a mprofile-kernel style mcount() call
from Michael Ellerman
- Fix endianness when reading TCEs from Alexey Kardashevskiy
- start rtasd before PCI probing from Greg Kurz
- PCI: rpaphp: Fix slot registration for multiple slots under a PHB
from Tyrel Datwyler
- powerpc/mm: Add memory barrier in __hugepte_alloc() from Sukadev
Bhattiprolu
Cleanups & fixes:
- Drop support for MPIC in pseries from Rashmica Gupta
- Define and use PPC64_ELF_ABI_v2/v1 from Michael Ellerman
- Remove unused symbols in asm-offsets.c from Rashmica Gupta
- Fix SRIOV not building without EEH enabled from Russell Currey
- Remove kretprobe_trampoline_holder from Thiago Jung Bauermann
- Reduce log level of PCI I/O space warning from Benjamin
Herrenschmidt
- Add array bounds checking to crash_shutdown_handlers from Suraj
Jitindar Singh
- Avoid -maltivec when using clang integrated assembler from Anton
Blanchard
- Fix array overrun in ppc_rtas() syscall from Andrew Donnellan
- Fix error return value in cmm_mem_going_offline() from Rasmus
Villemoes
- export cpu_to_core_id() from Mauricio Faria de Oliveira
- Remove old symbols from defconfigs from Andrew Donnellan
- Update obsolete comments in setup_32.c about entry conditions from
Benjamin Herrenschmidt
- Add comment explaining the purpose of setup_kdump_trampoline() from
Benjamin Herrenschmidt
- Merge the RELOCATABLE config entries for ppc32 and ppc64 from Kevin
Hao
- Remove RELOCATABLE_PPC32 from Kevin Hao
- Fix .long's in tlb-radix.c to more meaningful from Balbir Singh
Minor cleanups & fixes:
- Andrew Donnellan, Anna-Maria Gleixner, Anton Blanchard, Benjamin
Herrenschmidt, Bharata B Rao, Christophe Leroy, Colin Ian King,
Geliang Tang, Greg Kurz, Madhavan Srinivasan, Michael Ellerman,
Michael Ellerman, Stephen Rothwell, Stewart Smith.
Freescale updates from Scott:
- "Highlights include more 8xx optimizations, device tree updates,
and MVME7100 support."
PowerNV PCI hotplug from Gavin Shan:
- PCI: Add pcibios_setup_bridge()
- Override pcibios_setup_bridge()
- Remove PCI_RESET_DELAY_US
- Move pnv_pci_ioda_setup_opal_tce_kill() around
- Increase PE# capacity
- Allocate PE# in reverse order
- Create PEs in pcibios_setup_bridge()
- Setup PE for root bus
- Extend PCI bridge resources
- Make pnv_ioda_deconfigure_pe() visible
- Dynamically release PE
- Update bridge windows on PCI plug
- Delay populating pdn
- Support PCI slot ID
- Use PCI slot reset infrastructure
- Introduce pnv_pci_get_slot_id()
- Functions to get/set PCI slot state
- PCI/hotplug: PowerPC PowerNV PCI hotplug driver
- Print correct PHB type names
Power9 idle support from Shreyas B. Prabhu:
- set power_save func after the idle states are initialized
- Use PNV_THREAD_WINKLE macro while requesting for winkle
- make hypervisor state restore a function
- Rename idle_power7.S to idle_book3s.S
- Rename reusable idle functions to hardware agnostic names
- Make pnv_powersave_common more generic
- abstraction for saving SPRs before entering deep idle states
- Add platform support for stop instruction
- cpuidle/powernv: Use CPUIDLE_STATE_MAX instead of MAX_POWERNV_IDLE_STATES
- cpuidle/powernv: cleanup cpuidle-powernv.c
- cpuidle/powernv: Add support for POWER ISA v3 idle states
- Use deepest stop state when cpu is offlined
Power9 PMU from Madhavan Srinivasan:
- factor out power8 pmu macros and defines
- factor out power8 pmu functions
- factor out power8 __init_pmu code
- Add power9 event list macros for generic and cache events
- Power9 PMU support
- Export Power9 generic and cache events to sysfs
Power9 preliminary interrupt & PCI support from Benjamin Herrenschmidt:
- Add XICS emulation APIs
- Move a few exception common handlers to make room
- Add support for HV virtualization interrupts
- Add mechanism to force a replay of interrupts
- Add ICP OPAL backend
- Discover IODA3 PHBs
- pci: Remove obsolete SW invalidate
- opal: Add real mode call wrappers
- Rename TCE invalidation calls
- Remove SWINV constants and obsolete TCE code
- Rework accessing the TCE invalidate register
- Fallback to OPAL for TCE invalidations
- Use the device-tree to get available range of M64's
- Check status of a PHB before using it
- pci: Don't try to allocate resources that will be reassigned
Other Power9:
- Send SIGBUS on unaligned copy and paste from Chris Smart
- Large Decrementer support from Oliver O'Halloran
- Load Monitor Register Support from Jack Miller
Performance improvements from Anton Blanchard:
- Avoid load hit store in __giveup_fpu() and __giveup_altivec()
- Avoid load hit store in setup_sigcontext()
- Remove assembly versions of strcpy, strcat, strlen and strcmp
- Align hot loops of some string functions
eBPF JIT from Naveen N. Rao:
- Fix/enhance 32-bit Load Immediate implementation
- Optimize 64-bit Immediate loads
- Introduce rotate immediate instructions
- A few cleanups
- Isolate classic BPF JIT specifics into a separate header
- Implement JIT compiler for extended BPF
Operator Panel driver from Suraj Jitindar Singh:
- devicetree/bindings: Add binding for operator panel on FSP machines
- Add inline function to get rc from an ASYNC_COMP opal_msg
- Add driver for operator panel on FSP machines
Sparse fixes from Daniel Axtens:
- make some things static
- Introduce asm-prototypes.h
- Include headers containing prototypes
- Use #ifdef __BIG_ENDIAN__ #else for REG_BYTE
- kvm: Clarify __user annotations
- Pass endianness to sparse
- Make ppc_md.{halt, restart} __noreturn
MM fixes & cleanups from Aneesh Kumar K.V:
- radix: Update LPCR HR bit as per ISA
- use _raw variant of page table accessors
- Compile out radix related functions if RADIX_MMU is disabled
- Clear top 16 bits of va only on older cpus
- Print formation regarding the the MMU mode
- hash: Update SDR1 size encoding as documented in ISA 3.0
- radix: Update PID switch sequence
- radix: Update machine call back to support new HCALL.
- radix: Add LPID based tlb flush helpers
- radix: Add a kernel command line to disable radix
- Cleanup LPCR defines
Boot code consolidation from Benjamin Herrenschmidt:
- Move epapr_paravirt_early_init() to early_init_devtree()
- cell: Don't use flat device-tree after boot
- ge_imp3a: Don't use the flat device-tree after boot
- mpc85xx_ds: Don't use the flat device-tree after boot
- mpc85xx_rdb: Don't use the flat device-tree after boot
- Don't test for machine type in rtas_initialize()
- Don't test for machine type in smp_setup_cpu_maps()
- dt: Add of_device_compatible_match()
- Factor do_feature_fixup calls
- Move 64-bit feature fixup earlier
- Move 64-bit memory reserves to setup_arch()
- Use a cachable DART
- Move FW feature probing out of pseries probe()
- Put exception configuration in a common place
- Remove early allocation of the SMU command buffer
- Move MMU backend selection out of platform code
- pasemi: Remove IOBMAP allocation from platform probe()
- mm/hash: Don't use machine_is() early during boot
- Don't test for machine type to detect HEA special case
- pmac: Remove spurrious machine type test
- Move hash table ops to a separate structure
- Ensure that ppc_md is empty before probing for machine type
- Move 64-bit probe_machine() to later in the boot process
- Move 32-bit probe() machine to later in the boot process
- Get rid of ppc_md.init_early()
- Move the boot time info banner to a separate function
- Move setting of {i,d}cache_bsize to initialize_cache_info()
- Move the content of setup_system() to setup_arch()
- Move cache info inits to a separate function
- Re-order the call to smp_setup_cpu_maps()
- Re-order setup_panic()
- Make a few boot functions __init
- Merge 32-bit and 64-bit setup_arch()
Other new features:
- tty/hvc: Use IRQF_SHARED for OPAL hvc consoles from Sam Mendoza-Jonas
- tty/hvc: Use opal irqchip interface if available from Sam Mendoza-Jonas
- powerpc: Add module autoloading based on CPU features from Alastair D'Silva
- crypto: vmx - Convert to CPU feature based module autoloading from Alastair D'Silva
- Wake up kopald polling thread before waiting for events from Benjamin Herrenschmidt
- xmon: Dump ISA 2.06 SPRs from Michael Ellerman
- xmon: Dump ISA 2.07 SPRs from Michael Ellerman
- Add a parameter to disable 1TB segs from Oliver O'Halloran
- powerpc/boot: Add OPAL console to epapr wrappers from Oliver O'Halloran
- Assign fixed PHB number based on device-tree properties from Guilherme G. Piccoli
- pseries: Add pseries hotplug workqueue from John Allen
- pseries: Add support for hotplug interrupt source from John Allen
- pseries: Use kernel hotplug queue for PowerVM hotplug events from John Allen
- pseries: Move property cloning into its own routine from Nathan Fontenot
- pseries: Dynamic add entires to associativity lookup array from Nathan Fontenot
- pseries: Auto-online hotplugged memory from Nathan Fontenot
- pseries: Remove call to memblock_add() from Nathan Fontenot
cxl:
- Add set and get private data to context struct from Michael Neuling
- make base more explicitly non-modular from Paul Gortmaker
- Use for_each_compatible_node() macro from Wei Yongjun
- Frederic Barrat
- Abstract the differences between the PSL and XSL
- Make vPHB device node match adapter's
- Philippe Bergheaud
- Add mechanism for delivering AFU driver specific events
- Ignore CAPI adapters misplaced in switched slots
- Refine slice error debug messages
- Andrew Donnellan
- static-ify variables to fix sparse warnings
- PCI/hotplug: pnv_php: export symbols and move struct types needed by cxl
- PCI/hotplug: pnv_php: handle OPAL_PCI_SLOT_OFFLINE power state
- Add cxl_check_and_switch_mode() API to switch bi-modal cards
- remove dead Kconfig options
- fix potential NULL dereference in free_adapter()
- Ian Munsie
- Update process element after allocating interrupts
- Add support for CAPP DMA mode
- Fix allowing bogus AFU descriptors with 0 maximum processes
- Fix allocating a minimum of 2 pages for the SPA
- Fix bug where AFU disable operation had no effect
- Workaround XSL bug that does not clear the RA bit after a reset
- Fix NULL pointer dereference on kernel contexts with no AFU interrupts
- powerpc/powernv: Split cxl code out into a separate file
- Add cxl_slot_is_supported API
- Enable bus mastering for devices using CAPP DMA mode
- Move cxl_afu_get / cxl_afu_put to base
- Allow a default context to be associated with an external pci_dev
- Do not create vPHB if there are no AFU configuration records
- powerpc/powernv: Add support for the cxl kernel api on the real phb
- Add support for using the kernel API with a real PHB
- Add kernel APIs to get & set the max irqs per context
- Add preliminary workaround for CX4 interrupt limitation
- Add support for interrupts on the Mellanox CX4
- Workaround PE=0 hardware limitation in Mellanox CX4
- powerpc/powernv: Fix pci-cxl.c build when CONFIG_MODULES=n
selftests:
- Test unaligned copy and paste from Chris Smart
- Load Monitor Register Tests from Jack Miller
- Cyril Bur
- exec() with suspended transaction
- Use signed long to read perf_event_paranoid
- Fix usage message in context_switch
- Fix generation of vector instructions/types in context_switch
- Michael Ellerman
- Use "Delta" rather than "Error" in normal output
- Import Anton's mmap & futex micro benchmarks
- Add a test for PROT_SAO"
* tag 'powerpc-4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (263 commits)
powerpc/mm: Parenthesise IS_ENABLED() in if condition
tty/hvc: Use opal irqchip interface if available
tty/hvc: Use IRQF_SHARED for OPAL hvc consoles
selftests/powerpc: exec() with suspended transaction
powerpc: Improve comment explaining why we modify VRSAVE
powerpc/mm: Drop unused externs for hpte_init_beat[_v3]()
powerpc/mm: Rename hpte_init_lpar() and move the fallback to a header
powerpc/mm: Fix build break when PPC_NATIVE=n
crypto: vmx - Convert to CPU feature based module autoloading
powerpc: Add module autoloading based on CPU features
powerpc/powernv/ioda: Fix endianness when reading TCEs
powerpc/mm: Add memory barrier in __hugepte_alloc()
powerpc/modules: Never restore r2 for a mprofile-kernel style mcount() call
powerpc/ftrace: Separate the heuristics for checking call sites
powerpc: Merge 32-bit and 64-bit setup_arch()
powerpc/64: Make a few boot functions __init
powerpc: Re-order setup_panic()
powerpc: Re-order the call to smp_setup_cpu_maps()
powerpc/32: Move cache info inits to a separate function
powerpc/64: Move the content of setup_system() to setup_arch()
...
Pull x86 microcode updates from Thomas Gleixner:
- more work to make the microcode loader robust
- a fix for the micro code load precedence
- fixes for initrd loading with randomized memory
- less printk noise on SMP machines
* 'x86-microcode-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/asm, x86/microcode: Add __PAGE_OFFSET_BASE define on 32-bit
x86/microcode/intel: Fix initrd loading with CONFIG_RANDOMIZE_MEMORY=y
x86/microcode: Remove unused symbol exports
x86/microcode/intel: Do not issue microcode updates messages on each CPU
Documentation/microcode: Document some aspects for more clarity
x86/microcode/AMD: Make amd_ucode_patch[] static
x86/microcode/intel: Unexport save_mc_for_early()
x86/microcode/intel: Rename load_microcode_early() to find_microcode_patch()
x86/microcode: Propagate save_microcode_in_initrd() retval
x86/microcode: Get rid of find_cpio_data()'s dummy offset arg
lib/cpio: Make find_cpio_data()'s offset arg optional
x86/microcode: Fix suspend to RAM with builtin microcode
x86/microcode: Fix loading precedence
- Removal of most of_platform_populate() calls in arch code. Now the DT
core code calls it in the default case and platforms only need to call
it if they have special needs.
- Use pr_fmt on all the DT core print statements.
- CoreSight binding doc improvements to block name descriptions.
- Add dt_to_config script which can parse dts files and list
corresponding kernel config options.
- Fix memory leak hit with a PowerMac DT.
- Correct a bunch of STMicro compatible strings to use the correct
vendor prefix.
- Fix DA9052 PMIC binding doc to match what is actually used in dts
files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXm9KcAAoJEPr7XbWNvGHDRT4QAIIIOSB4AWHardnMLROgGge9
aOQKZ/05O9feOcxYKe8FkQbcH+IujJjrUL+yrRD36yGQPAyBP21gtcmmfrkCcwFM
kH915f/JbGvXpfwEf8dcarHhzYH6FFJiQGduPpWfwSSWynx+xq5EKPwCqYzMg8bN
SExxt7vUx1MKFOExZ0K8BNCo8VMVLUWQoJ1DNeJDuL25Op4EU3i2l1HQNYV/3XDk
BSA3x7Lw3GjrWEH20VWYn2Azq1OFLY+E2FC2lnG4nbkk5X8dZbUH9PR1Sk7uTQDj
uxTjWe59NBpliCxKSAbMbTAU/WwSB1pJ0I+zDJBiQsdFT+nb5F4zOrs3qSKHa/A9
Rv6AC8k5gdSMrDB1dOspfF2vWvOOInXgNV4/Kza0D92mbCpwyUuF+vhE6rfcMrZU
OiD7rj2/fvO7Y9fUAhrp6zrfrOfH9B1Z9vS+940AlK96YwPE2+J0SA2vBxR/wg8H
7fj4Ud5X+SFisXWQhh5Wlv0W9o6e7C7fsi8vpkQ7gufmezLFWVnJKsUfQaxGEwhG
Hkhm9kuSHHMd+6dEnn2756DnNfJAtQv6rSR0/QR4Lf9y5L4dvR3kAQIci8X/nx4P
sIk+IJWGZG6wziZq59hh+SO6HEqdSNuvh+5sbR0iUimdE/1HsDBdPiocXf/r8iwK
NY9nGeZPRrXmFgdpoZfm
=wLMr
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- remove most of_platform_populate() calls in arch code. Now the DT
core code calls it in the default case and platforms only need to
call it if they have special needs
- use pr_fmt on all the DT core print statements
- CoreSight binding doc improvements to block name descriptions
- add dt_to_config script which can parse dts files and list
corresponding kernel config options
- fix memory leak hit with a PowerMac DT
- correct a bunch of STMicro compatible strings to use the correct
vendor prefix
- fix DA9052 PMIC binding doc to match what is actually used in dts
files
* tag 'devicetree-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (35 commits)
documentation: da9052: Update regulator bindings names to match DA9052/53 DTS expectations
xtensa: Partially Revert "xtensa: Remove unnecessary of_platform_populate with default match table"
xtensa: Fix build error due to missing include file
MIPS: ath79: Add missing include file
Fix spelling errors in Documentation/devicetree
ARM: dts: fix STMicroelectronics compatible strings
powerpc/dts: fix STMicroelectronics compatible strings
Documentation: dt: i2c: use correct STMicroelectronics vendor prefix
scripts/dtc: dt_to_config - kernel config options for a devicetree
of: fdt: mark unflattened tree as detached
of: overlay: add resolver error prints
coresight: document binding acronyms
Documentation/devicetree: document cavium-pip rx-delay/tx-delay properties
of: use pr_fmt prefix for all console printing
of/irq: Mark initialised interrupt controllers as populated
of: fix memory leak related to safe_name()
Revert "of/platform: export of_default_bus_match_table"
of: unittest: use of_platform_default_populate() to populate default bus
memory: omap-gpmc: use of_platform_default_populate() to populate default bus
bus: uniphier-system-bus: use of_platform_default_populate() to populate default bus
...
drivers, along with a pretty standard number of new drivers. The core
recieved a small number of updates as well.
Core changes of note:
* Removed CLK_IS_ROOT flag
New clk provider drivers:
* Renesas r8a7796 Clock Pulse Generator / Module Standby and Software
Reset
* Allwinner sun8i H3 Clock Controller Unit
* AmLogic meson8b clock controller (rewritten)
* AmLogic gxbb clock controller
* Support for some new ICs was added by simple changes to static data
tables for chips sharing the same family
Driver updates of note:
* the Allwinner sunxi clock driver infrastucture was rewritten to
comform to the state of the art at drivers/clk/sunxi-ng. The old
implementation is still supported for backwards compatibility with the
DT ABI
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJXm9LNAAoJEKI6nJvDJaTUHYcP/1oKTHA4uSPux2+5l9vApEJc
eSV0oSEP/zDDwYfV4xRt1byAOtzHe3R4p5zDGShnk3+CCwXbQSLGmFJFmZDoSs5E
ulftXA8uRV4ac0SEh86BOlstdJHGOVo7Q38XtdPvgKRTv58+ZqHuFcvB726bWY/I
GMzVTkpugbn5U7e3MLM58gkBoqa8BS9uIdsf5q/JIxdpe+VgUtjmioH9Rz6G5U5Y
T6ObeU6HNusDaz6kUJIiAEkl4UNHk+aebnY7FTbwd9JGGySp5nEknVY7tSMeC6iU
hG/knzdMiasa5yv0xdW3/OxnKCQtEeuPPHnJDSXWc9yb20vNs2QhRtd8uckMGHOH
X7fXq9xoLxDH81AggW188g7+xfhx7J+ASpjHmHs74itUIoqhhy61PM3I95yQ8m6s
QDkInqSszFd2C7OiYsy6m5XS0K8g0jyA2tzWhxlIZNVAl7yP71+HVLJ45NNKCPkb
oYbMx4ho538Tl6+c6HHJG0vC3XWSdHbvwMOKyE9k/GyrIJ7FxLZS3BLOYPm6u9t4
9n041MbtBb/UrWVi8kMSdmBjIIs6VSGjq5gwRFAqoPQt3VkPuy0IfnwIpjdE1aFz
PbDJQF4ze7D3JgH2rWtivXbCTRthTANmoar299xjSwwb99TSlP2IABY3cNnJrhPr
9/PGShM3hqRpBEUnEmt+
=1dpY
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Michael Turquette:
"The bulk of the changes are updates and fixes to existing clk provider
drivers, along with a pretty standard number of new drivers. The core
recieved a small number of updates as well.
Core changes of note:
- removed CLK_IS_ROOT flag
New clk provider drivers:
- Renesas r8a7796 clock pulse generator / module standby and
software reset
- Allwinner sun8i H3 clock controller unit
- AmLogic meson8b clock controller (rewritten)
- AmLogic gxbb clock controller
- support for some new ICs was added by simple changes to static
data tables for chips sharing the same family
Driver updates of note:
- the Allwinner sunxi clock driver infrastucture was rewritten to
comform to the state of the art at drivers/clk/sunxi-ng. The old
implementation is still supported for backwards compatibility with
the DT ABI"
* tag 'clk-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (162 commits)
clk: Makefile: re-sort and clean up
Revert "clk: gxbb: expose CLKID_MMC_PCLK"
clk: samsung: Allow modular build of the Audio Subsystem CLKCON driver
clk: samsung: make clk-s5pv210-audss explicitly non-modular
clk: exynos5433: remove CLK_IGNORE_UNUSED flag from SPI clocks
clk: oxnas: Add hardware dependencies
clk: imx7d: do not set parent of ethernet time/ref clocks
ARM: dt: sun8i: switch the H3 to the new CCU driver
clk: sunxi-ng: h3: Fix Kconfig symbol typo
clk: sunxi-ng: h3: Fix audio clock divider offset
clk: sunxi-ng: Add H3 clocks
clk: sunxi-ng: Add N-K-M-P factor clock
clk: sunxi-ng: Add N-K-M Factor clock
clk: sunxi-ng: Add N-M-factor clock support
clk: sunxi-ng: Add N-K-factor clock support
clk: sunxi-ng: Add M-P factor clock support
clk: sunxi-ng: Add divider
clk: sunxi-ng: Add phase clock support
clk: sunxi-ng: Add mux clock support
clk: sunxi-ng: Add gate clock support
...
Pull security subsystem updates from James Morris:
"Highlights:
- TPM core and driver updates/fixes
- IPv6 security labeling (CALIPSO)
- Lots of Apparmor fixes
- Seccomp: remove 2-phase API, close hole where ptrace can change
syscall #"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (156 commits)
apparmor: fix SECURITY_APPARMOR_HASH_DEFAULT parameter handling
tpm: Add TPM 2.0 support to the Nuvoton i2c driver (NPCT6xx family)
tpm: Factor out common startup code
tpm: use devm_add_action_or_reset
tpm2_i2c_nuvoton: add irq validity check
tpm: read burstcount from TPM_STS in one 32-bit transaction
tpm: fix byte-order for the value read by tpm2_get_tpm_pt
tpm_tis_core: convert max timeouts from msec to jiffies
apparmor: fix arg_size computation for when setprocattr is null terminated
apparmor: fix oops, validate buffer size in apparmor_setprocattr()
apparmor: do not expose kernel stack
apparmor: fix module parameters can be changed after policy is locked
apparmor: fix oops in profile_unpack() when policy_db is not present
apparmor: don't check for vmalloc_addr if kvzalloc() failed
apparmor: add missing id bounds check on dfa verification
apparmor: allow SYS_CAP_RESOURCE to be sufficient to prlimit another task
apparmor: use list_next_entry instead of list_entry_next
apparmor: fix refcount race when finding a child profile
apparmor: fix ref count leak when profile sha1 hash is read
apparmor: check that xindex is in trans_table bounds
...
Buck and LDO binding name changes.
The binding names for the regulators have been changed to match the current
expectation from existing device tree source files.
This fix rectifies the disparity between what currently exists in some
.dts[i] board files and what is listed in this binding document. This
change re-aligns those differences and also brings the binding document
in-line with the expectations of the product datasheet from Dialog
Semiconductor.
Bucks and LDOs now follow the expected notation:
{ buck1, buck2, buck3, buck4 }
{ ldo1, ldo2, ldo3, ldo4, ldo5, ldo6, ldo7, ldo8, ldo9, ldo10 }
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Rob Herring <robh@kernel.org>
changes are:
. The function pid code uses the event pid filtering logic
. [ku]probe events have access to current->comm
. trace_printk now has sample code
. PCI devices now trace physical addresses
. stack tracing has less unnessary functions traced
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXl+d2AAoJEKKk/i67LK/83QEH/RDJ0mcfFVsuEeOnZZrZXABm
4Rxk4FE5UAD+TSrVycwwzcbQab1iPK63mMdYvIBvaOiIC6/OJaEVM7jzZxnNGqmr
pj0H8bxwOr58pe5pfnP92ow5qTLLzsXraWNl5sRXhSSHON7CXpGVzkErB58GmMYd
8p6d9ziifQjo8X2O6XC9rGAvYLY5kEkVvyfuE1hI7muNTeOjyOT4EqpkNzxdBk+I
QkGZGsk3Xhc8II9nu8FPWkaD26TatGJoZtZmVWHOzfsb3HNzG4RXla+WVOQ5u1HV
noVyB1CJHhkO5CEBPdYIqwBWPQU4B9HfG4gVcUpDDVRxfzMpnEcKi1uwe+uDjfs=
=XFcv
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"This is mostly clean ups and small fixes. Some of the more visible
changes are:
- The function pid code uses the event pid filtering logic
- [ku]probe events have access to current->comm
- trace_printk now has sample code
- PCI devices now trace physical addresses
- stack tracing has less unnessary functions traced"
* tag 'trace-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
printk, tracing: Avoiding unneeded blank lines
tracing: Use __get_str() when manipulating strings
tracing, RAS: Cleanup on __get_str() usage
tracing: Use outer () on __get_str() definition
ftrace: Reduce size of function graph entries
tracing: Have HIST_TRIGGERS select TRACING
tracing: Using for_each_set_bit() to simplify trace_pid_write()
ftrace: Move toplevel init out of ftrace_init_tracefs()
tracing/function_graph: Fix filters for function_graph threshold
tracing: Skip more functions when doing stack tracing of events
tracing: Expose CPU physical addresses (resource values) for PCI devices
tracing: Show the preempt count of when the event was called
tracing: Add trace_printk sample code
tracing: Choose static tp_printk buffer by explicit nesting count
tracing: expose current->comm to [ku]probe events
ftrace: Have set_ftrace_pid use the bitmap like events do
tracing: Move pid_list write processing into its own function
tracing: Move the pid_list seq_file functions to be global
tracing: Move filtered_pid helper functions into trace.c
tracing: Make the pid filtering helper functions global
1/ Replace pcommit with ADR / directed-flushing:
The pcommit instruction, which has not shipped on any product, is
deprecated. Instead, the requirement is that platforms implement either
ADR, or provide one or more flush addresses per nvdimm. ADR
(Asynchronous DRAM Refresh) flushes data in posted write buffers to the
memory controller on a power-fail event. Flush addresses are defined in
ACPI 6.x as an NVDIMM Firmware Interface Table (NFIT) sub-structure:
"Flush Hint Address Structure". A flush hint is an mmio address that
when written and fenced assures that all previous posted writes
targeting a given dimm have been flushed to media.
2/ On-demand ARS (address range scrub):
Linux uses the results of the ACPI ARS commands to track bad blocks
in pmem devices. When latent errors are detected we re-scrub the media
to refresh the bad block list, userspace can also request a re-scrub at
any time.
3/ Support for the Microsoft DSM (device specific method) command format.
4/ Support for EDK2/OVMF virtual disk device memory ranges.
5/ Various fixes and cleanups across the subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xCBG
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
- Replace pcommit with ADR / directed-flushing.
The pcommit instruction, which has not shipped on any product, is
deprecated. Instead, the requirement is that platforms implement
either ADR, or provide one or more flush addresses per nvdimm.
ADR (Asynchronous DRAM Refresh) flushes data in posted write buffers
to the memory controller on a power-fail event.
Flush addresses are defined in ACPI 6.x as an NVDIMM Firmware
Interface Table (NFIT) sub-structure: "Flush Hint Address Structure".
A flush hint is an mmio address that when written and fenced assures
that all previous posted writes targeting a given dimm have been
flushed to media.
- On-demand ARS (address range scrub).
Linux uses the results of the ACPI ARS commands to track bad blocks
in pmem devices. When latent errors are detected we re-scrub the
media to refresh the bad block list, userspace can also request a
re-scrub at any time.
- Support for the Microsoft DSM (device specific method) command
format.
- Support for EDK2/OVMF virtual disk device memory ranges.
- Various fixes and cleanups across the subsystem.
* tag 'libnvdimm-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (41 commits)
libnvdimm-btt: Delete an unnecessary check before the function call "__nd_device_register"
nfit: do an ARS scrub on hitting a latent media error
nfit: move to nfit/ sub-directory
nfit, libnvdimm: allow an ARS scrub to be triggered on demand
libnvdimm: register nvdimm_bus devices with an nd_bus driver
pmem: clarify a debug print in pmem_clear_poison
x86/insn: remove pcommit
Revert "KVM: x86: add pcommit support"
nfit, tools/testing/nvdimm/: unify shutdown paths
libnvdimm: move ->module to struct nvdimm_bus_descriptor
nfit: cleanup acpi_nfit_init calling convention
nfit: fix _FIT evaluation memory leak + use after free
tools/testing/nvdimm: add manufacturing_{date|location} dimm properties
tools/testing/nvdimm: add virtual ramdisk range
acpi, nfit: treat virtual ramdisk SPA as pmem region
pmem: kill __pmem address space
pmem: kill wmb_pmem()
libnvdimm, pmem: use nvdimm_flush() for namespace I/O writes
fs/dax: remove wmb_pmem()
libnvdimm, pmem: flush posted-write queues on shutdown
...
New drivers:
- New driver for Oxnas pin control and GPIO. This ARM-based chipset
is used in a few storage (NAS) type devices.
- New driver for the MAX77620/MAX20024 pin controller portions.
- New driver for the Intel Merrifield pin controller.
New subdrivers:
- New subdriver for the Qualcomm MDM9615
- New subdriver for the STM32F746 MCU
- New subdriver for the Broadcom NSP SoC.
Cleanups:
- Demodularization of bool compiled-in drivers.
Apart from this there is just regular incremental improvements to
a lot of drivers, especially Uniphier and PFC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXmcthAAoJEEEQszewGV1z2ukP/1T34tgMllEzBcnyTM28pnPl
80anOiCi/jkLuW1hYTLc4Rx0tZT2oWw9hrZdKGNMuzNCaJSmFaRhUrbzxhZ8E+6O
3AHYSopAYUTKVYJsuY+fs3HbNajKBsSWYdmxin4e953BPudLjhZ2WliDXxupsbwZ
/KI6s8J2pDZcPurrlozT5Avp3BTwwCq+fo12NIMkkmuhURb69OsDAVjPlwjocq73
BKcdH8AdgO7w5Ss5/IQbvrhyuFc2kCQ/wH1tiuE2a4iYWhp+QkMOEqWUSdYs33bx
Sbn3KTK6IYYS1eb4xharh7H/zoBs20aCQ2kS8qbYmG+Fv7rB7qboI0qM7m7+25O8
7F6Tf4F0HUg6IjcABcI5lFuTxACBG8p5ZlmQAp/36EaeIblLALBCvd1ArmZ6fdG+
Pzu5vLaZBAmxQn6EseHLAJkH4FEzV7II/Sk7U23TINHUpl/L2GJO+6irz7eelKAk
XED6mrNU8rRnZMka02ZnIgIbABG7ELNJsRxEnf8k9CX7cfi4p568eZeR1nfKcy4+
uldJLipNv3NfwuRY5JEEa7pFW4azYmnzS1GcoVYPy7snYc4Rr8cbBD6YvcxyMhVz
RXHc21mj45JnboldAYU59t5BbVZNwZqF8hmg935ngoaZjYfhhnfGoNQF7hy6/1fS
bwojoQtBqGcriKZYGs0o
=po0g
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.8 kernel cycle.
Nothing stands out as especially exiting: new drivers, new subdrivers,
lots of cleanups and incremental features.
Business as usual.
New drivers:
- New driver for Oxnas pin control and GPIO. This ARM-based chipset
is used in a few storage (NAS) type devices.
- New driver for the MAX77620/MAX20024 pin controller portions.
- New driver for the Intel Merrifield pin controller.
New subdrivers:
- New subdriver for the Qualcomm MDM9615
- New subdriver for the STM32F746 MCU
- New subdriver for the Broadcom NSP SoC.
Cleanups:
- Demodularization of bool compiled-in drivers.
Apart from this there is just regular incremental improvements to a
lot of drivers, especially Uniphier and PFC"
* tag 'pinctrl-v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (131 commits)
pinctrl: fix pincontrol definition for marvell
pinctrl: xway: fix typo
Revert "pinctrl: amd: make it explicitly non-modular"
pinctrl: iproc: Add NSP and Stingray GPIO support
pinctrl: Update iProc GPIO DT bindings
pinctrl: bcm: add OF dependencies
pinctrl: ns2: remove redundant dev_err call in ns2_pinmux_probe()
pinctrl: Add STM32F746 MCU support
pinctrl: intel: Protect set wake flow by spin lock
pinctrl: nsp: remove redundant dev_err call in nsp_pinmux_probe()
pinctrl: uniphier: add Ethernet pin-mux settings
sh-pfc: Use PTR_ERR_OR_ZERO() to simplify the code
pinctrl: ns2: fix return value check in ns2_pinmux_probe()
pinctrl: qcom: update DT bindings with ebi2 groups
pinctrl: qcom: establish proper EBI2 pin groups
pinctrl: imx21: Remove the MODULE_DEVICE_TABLE() macro
Documentation: dt: Add new compatible to STM32 pinctrl driver bindings
includes: dt-bindings: Add STM32F746 pinctrl DT bindings
pinctrl: sunxi: fix nand0 function name for sun8i
pinctrl: uniphier: remove pointless pin-mux settings for PH1-LD11
...
Merge more updates from Andrew Morton:
"The rest of MM"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (101 commits)
mm, compaction: simplify contended compaction handling
mm, compaction: introduce direct compaction priority
mm, thp: remove __GFP_NORETRY from khugepaged and madvised allocations
mm, page_alloc: make THP-specific decisions more generic
mm, page_alloc: restructure direct compaction handling in slowpath
mm, page_alloc: don't retry initial attempt in slowpath
mm, page_alloc: set alloc_flags only once in slowpath
lib/stackdepot.c: use __GFP_NOWARN for stack allocations
mm, kasan: switch SLUB to stackdepot, enable memory quarantine for SLUB
mm, kasan: account for object redzone in SLUB's nearest_obj()
mm: fix use-after-free if memory allocation failed in vma_adjust()
zsmalloc: Delete an unnecessary check before the function call "iput"
mm/memblock.c: fix index adjustment error in __next_mem_range_rev()
mem-hotplug: alloc new page from a nearest neighbor node when mem-offline
mm: optimize copy_page_to/from_iter_iovec
mm: add cond_resched() to generic_swapfile_activate()
Revert "mm, mempool: only set __GFP_NOMEMALLOC if there are free elements"
mm, compaction: don't isolate PageWriteback pages in MIGRATE_SYNC_LIGHT mode
mm: hwpoison: remove incorrect comments
make __section_nr() more efficient
...
Node-based reclaim requires node-based LRUs and locking. This is a
preparation patch that just moves the lru_lock to the node so later
patches are easier to review. It is a mechanical change but note this
patch makes contention worse because the LRU lock is hotter and direct
reclaim and kswapd can contend on the same lock even when reclaiming
from different zones.
Link: http://lkml.kernel.org/r/1467970510-21195-3-git-send-email-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Reviewed-by: Minchan Kim <minchan@kernel.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This time we have bit of largish changes:
New drivers:
- Xilinx zynqmp dma engine driver.
- Marvell xor2 driver.
Updates:
- dmatest sg support.
- updates and enhancements to Xilinx drivers, adding of cyclic mode.
- clock handling fixes across drivers.
- removal of OOM messages on kzalloc across subsystem.
- interleaved transfers support in omap driver.
- runtime pm support in qcom bam dma.
- tasklet kill freeup across drivers.
- irq cleanup on remove across drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tYp0
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-4.8-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
"This time we have bit of largish changes: two new drivers, bunch of
updates and cleanups to existing set. Nothing super exciting though.
New drivers:
- Xilinx zynqmp dma engine driver
- Marvell xor2 driver
Updates:
- dmatest sg support
- updates and enhancements to Xilinx drivers, adding of cyclic mode
- clock handling fixes across drivers
- removal of OOM messages on kzalloc across subsystem
- interleaved transfers support in omap driver
- runtime pm support in qcom bam dma
- tasklet kill freeup across drivers
- irq cleanup on remove across drivers"
* tag 'dmaengine-4.8-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (94 commits)
dmaengine: k3dma: add missing clk_disable_unprepare() on error in k3_dma_probe()
dmaengine: zynqmp_dma: add missing MODULE_LICENSE
dmaengine: qcom_hidma: use for_each_matching_node() macro
dmaengine: zynqmp_dma: Fix static checker warning
dmaengine: omap-dma: Support for interleaved transfer
dmaengine: ioat: statify symbol
dmaengine: pxa_dma: implement device_synchronize
dmaengine: imx-sdma: remove assignment never used
dmaengine: imx-sdma: remove dummy assignment
dmaengine: cppi: remove unused and bogus check
dmaengine: qcom_hidma_lli: kill the tasklets upon exit
dmaengine: pxa_dma: remove owner assignment
dmaengine: fsl_raid: remove owner assignment
dmaengine: coh901318: remove owner assignment
dmaengine: qcom_hidma: kill the tasklets upon exit
dmaengine: txx9dmac: explicitly freeup irq
dmaengine: sirf-dma: kill the tasklets upon exit
dmaengine: s3c24xx: kill the tasklets upon exit
dmaengine: s3c24xx: explicitly freeup irq
dmaengine: pl330: explicitly freeup irq
...
Introduce remoteproc driver for controlling the modem/DSP Hexagon CPU
found in a multitude of Qualcomm platform. Also cleans up a race
condition/potential leak during registration of remoteprocs and includes
devicetree bindings in the MAINTAINERS entry.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XlWX
-----END PGP SIGNATURE-----
Merge tag 'rproc-v4.8' of git://github.com/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
"Introduce remoteproc driver for controlling the modem/DSP Hexagon CPU
found in a multitude of Qualcomm platform.
Also cleans up a race condition/potential leak during registration of
remoteprocs and includes devicetree bindings in the MAINTAINERS entry"
* tag 'rproc-v4.8' of git://github.com/andersson/remoteproc:
remoteproc: qcom: hexagon: Clean up mpss validation
remoteproc: qcom: remove redundant dev_err call in q6v5_init_mem()
remoteproc: qcom: Driver for the self-authenticating Hexagon v5
dt-binding: remoteproc: Introduce Hexagon loader binding
remoteproc: Fix potential race condition in rproc_add
MAINTAINERS: Add file patterns for remoteproc device tree bindings
Pull HID updates from Jiri Kosina:
- new hid-alps driver for ALPS Touchpad-Stick device, from Masaki Ota
- much improved and generalized HID led handling, and merge of
specialized hid-thingm driver into this generic hid-led one, from
Heiner Kallweit
- i2c-hid power management improvements from Fu Zhonghui and Guohua
Zhong
- uhid initialization race fix from Roderick Colenbrander
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (21 commits)
HID: add usb device id for Apple Magic Keyboard
HID: hid-led: fix Delcom support on big endian systems
HID: hid-led: add support for Greynut Luxafor
HID: hid-led: add support for Delcom Visual Signal Indicator G2
HID: hid-led: remove report id from struct hidled_config
HID: alps: a few cleanups
HID: remove ThingM blink(1) driver
HID: hid-led: add support for ThingM blink(1)
HID: hid-led: add support for reading from LED devices
HID: hid-led: add support for devices with multiple independent LEDs
HID: i2c-hid: set power sleep before shutdown
HID: alps: match alps devices in core
HID: thingm: simplify debug output code
HID: alps: pass correct sizes to hid_hw_raw_request()
HID: alps: struct u1_dev *priv is internal to the driver
HID: add Alps I2C HID Touchpad-Stick support
HID: led: fix config
usb: misc: remove outdated USB LED driver
HID: migrate USB LED driver from usb misc to hid
HID: i2c_hid: enable i2c-hid devices to suspend/resume asynchronously
...
Pull vfs updates from Al Viro:
"Assorted cleanups and fixes.
Probably the most interesting part long-term is ->d_init() - that will
have a bunch of followups in (at least) ceph and lustre, but we'll
need to sort the barrier-related rules before it can get used for
really non-trivial stuff.
Another fun thing is the merge of ->d_iput() callers (dentry_iput()
and dentry_unlink_inode()) and a bunch of ->d_compare() ones (all
except the one in __d_lookup_lru())"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (26 commits)
fs/dcache.c: avoid soft-lockup in dput()
vfs: new d_init method
vfs: Update lookup_dcache() comment
bdev: get rid of ->bd_inodes
Remove last traces of ->sync_page
new helper: d_same_name()
dentry_cmp(): use lockless_dereference() instead of smp_read_barrier_depends()
vfs: clean up documentation
vfs: document ->d_real()
vfs: merge .d_select_inode() into .d_real()
unify dentry_iput() and dentry_unlink_inode()
binfmt_misc: ->s_root is not going anywhere
drop redundant ->owner initializations
ufs: get rid of redundant checks
orangefs: constify inode_operations
missed comment updates from ->direct_IO() prototype change
file_inode(f)->i_mapping is f->f_mapping
trim fsnotify hooks a bit
9p: new helper - v9fs_parent_fid()
debugfs: ->d_parent is never NULL or negative
...
* proper runtime pm support for omap-ssi and ssi-protocol
* misc. fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WPyp
-----END PGP SIGNATURE-----
Merge tag 'hsi-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi
Pull HSI updates from Sebastian Reichel:
- proper runtime pm support for omap-ssi and ssi-protocol
- misc fixes
* tag 'hsi-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-hsi: (24 commits)
HSI: omap_ssi: drop pm_runtime_irq_safe
HSI: omap_ssi_port: use rpm autosuspend API
HSI: omap_ssi: call msg->complete() from process context
HSI: omap_ssi_port: ensure clocks are kept enabled during transfer
HSI: omap_ssi_port: replace pm_runtime_put_sync with non-sync variant
HSI: omap_ssi_port: avoid calling runtime_pm_*_sync inside spinlock
HSI: omap_ssi_port: avoid pm_runtime_get_sync in ssi_start_dma and ssi_start_pio
HSI: omap_ssi_port: switch to threaded pio irq
HSI: omap_ssi_core: remove pm_runtime_get_sync call from tasklet
HSI: omap_ssi_core: use pm_runtime_put instead of pm_runtime_put_sync
HSI: omap_ssi_port: prepare start_tx/stop_tx for blocking pm_runtime calls
HSI: core: switch port event notifier from atomic to blocking
HSI: omap_ssi_port: replace wkin_cken with atomic bitmap operations
HSI: omap_ssi: convert cawake irq handler to thread
HSI: ssi_protocol: fix ssip_xmit invocation
HSI: ssi_protocol: replace spin_lock with spin_lock_bh
HSI: ssi_protocol: avoid ssi_waketest call with held spinlock
HSI: omap_ssi: do not reset module
HSI: omap_ssi_port: remove useless newline
hsi: Only descend into hsi directory when CONFIG_HSI is set
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=CN+v
-----END PGP SIGNATURE-----
Merge tag 'media/v4.8-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media documentation updates from Mauro Carvalho Chehab:
"This patch series does the conversion of all media documentation stuff
to Restrutured Text markup format and add them to the
Documentation/index.rst file.
The media documentation was grouped into 4 books:
- media uAPI
- media kAPI
- V4L driver-specific documentation
- DVB driver-specific documentation
It also contains several documentation improvements and one fixup
patch for a core issue with cropcap.
PS. After this patch series, the media DocBook is deprecated and
should be removed. I'll add such patch on a future pull request"
* tag 'media/v4.8-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (322 commits)
[media] cx23885-cardlist.rst: add a new card
[media] doc-rst: add some needed escape codes
[media] doc-rst: kapi: use :c:func: instead of :cpp:func
doc-rst: kernel-doc: fix a change introduced by mistake
[media] v4l2-ioctl.h add debug info for struct v4l2_ioctl_ops
[media] dvb_ringbuffer.h: some documentation improvements
[media] v4l2-ctrls.h: fully document the header file
[media] doc-rst: Fix some typedef ugly warnings
[media] doc-rst: reorganize the kAPI v4l2 chapters
[media] rename v4l2-framework.rst to v4l2-intro.rst
[media] move V4L2 clocks to a separate .rst file
[media] v4l2-fh.rst: add cross references and markups
[media] v4l2-fh.rst: add fh contents from v4l2-framework.rst
[media] v4l2-fh.h: add documentation for it
[media] v4l2-event.rst: add cross-references and markups
[media] v4l2-event.h: document all functions
[media] v4l2-event.rst: add text from v4l2-framework.rst
[media] v4l2-framework.rst: remove videobuf quick chapter
[media] v4l2-dev: add cross-references and improve markup
[media] doc-rst: move v4l2-dev doc to a separate file
...
This update includes the usual round of driver updates (fcoe, lpfc,
ufs, qla2xxx, hisi_sas). The most important other change is removing
the flag to allow non-blk_mq on a per host basis (it's unused); there
is still a global module parameter for all of SCSI just in case. The
rest are an assortment of minor fixes and typo updates.
Signed-off-by: James Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=vRgI
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This update includes the usual round of driver updates (fcoe, lpfc,
ufs, qla2xxx, hisi_sas). The most important other change is removing
the flag to allow non-blk_mq on a per host basis (it's unused); there
is still a global module parameter for all of SCSI just in case.
The rest are an assortment of minor fixes and typo updates"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (101 commits)
scsi:libsas: fix oops caused by assigning a freed task to ->lldd_task
fnic: pci_dma_mapping_error() doesn't return an error code
scsi: lpfc: avoid harmless comparison warning
fcoe: implement FIP VLAN responder
fcoe: Rename 'fip_frame' to 'fip_vn2vn_notify_frame'
lpfc: call lpfc_sli_validate_fcp_iocb() with the hbalock held
scsi: ufs: remove unnecessary goto label
hpsa: change hpsa_passthru_ioctl timeout
hpsa: correct skipping masked peripherals
qla2xxx: Update driver version to 8.07.00.38-k
qla2xxx: Fix BBCR offset
qla2xxx: Fix duplicate message id.
qla2xxx: Disable the adapter and skip error recovery in case of register disconnect.
qla2xxx: Separate ISP type bits out from device type.
qla2xxx: Correction to function qla26xx_dport_diagnostics().
qla2xxx: Add support to handle Loop Init error Asynchronus event.
qla2xxx: Let DPORT be enabled purely by nvram.
qla2xxx: Add bsg interface to support statistics counter reset.
qla2xxx: Add bsg interface to support D_Port Diagnostics.
qla2xxx: Check for device state before unloading the driver.
...
Pull input updates from Dmitry Torokhov:
"Updates for the input subsystem. This contains the following new
drivers promised in the last merge window:
- driver for touchscreen controller found in Surface 3
- driver for Pegasus Notetaker tablet
- driver for Atmel Captouch Buttons
- driver for Raydium I2C touchscreen controllers
- powerkey driver for HISI 65xx SoC
plus a few fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (40 commits)
Input: tty/vt/keyboard - use memdup_user()
Input: pegasus_notetaker - set device mode in reset_resume() if in use
Input: pegasus_notetaker - cancel workqueue's work in suspend()
Input: pegasus_notetaker - fix usb_autopm calls to be balanced
Input: pegasus_notetaker - handle usb control msg errors
Input: wacom_w8001 - handle errors from input_mt_init_slots()
Input: wacom_w8001 - resolution wasn't set for ABS_MT_POSITION_X/Y
Input: pixcir_ts - add support for axis inversion / swapping
Input: icn8318 - use of_touchscreen helpers for inverting / swapping axes
Input: edt-ft5x06 - add support for inverting / swapping axes
Input: of_touchscreen - add support for inverted / swapped axes
Input: synaptics-rmi4 - use the RMI_F11_REL_BYTES define in rmi_f11_rel_pos_report
Input: synaptics-rmi4 - remove unneeded variable
Input: synaptics-rmi4 - remove pointer to rmi_function in f12_data
Input: synaptics-rmi4 - support regulator supplies
Input: raydium_i2c_ts - check CRC of incoming packets
Input: xen-kbdfront - prefer xenbus_write() over xenbus_printf() where possible
Input: fix a double word "is is" in include/linux/input.h
Input: add powerkey driver for HISI 65xx SoC
Input: apanel - spelling mistake - "skiping" -> "skipping"
...
Pull i2c updates from Wolfram Sang:
"Here is the I2C pull request for 4.8:
- the core and i801 driver gained support for SMBus Host Notify
- core support for more than one address in DT
- i2c_add_adapter() has now better error messages. We can remove all
error messages from drivers calling it as a next step.
- bigger updates to rk3x driver to support rk3399 SoC
- the at24 eeprom driver got refactored and can now read special
variants with unique serials or fixed MAC addresses.
The rest is regular driver updates and bugfixes"
* 'i2c/for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (66 commits)
i2c: i801: use IS_ENABLED() instead of checking for built-in or module
Documentation: i2c: slave: give proper example for pm usage
Documentation: i2c: slave: describe buffer problems a bit better
i2c: bcm2835: Don't complain on -EPROBE_DEFER from getting our clock
i2c: i2c-smbus: drop useless stubs
i2c: efm32: fix a failure path in efm32_i2c_probe()
Revert "i2c: core: Cleanup I2C ACPI namespace"
Revert "i2c: core: Add function for finding the bus speed from ACPI"
i2c: Update the description of I2C_SMBUS
i2c: i2c-smbus: fix i2c_handle_smbus_host_notify documentation
eeprom: at24: tweak the loop_until_timeout() macro
eeprom: at24: add support for at24mac series
eeprom: at24: support reading the serial number for 24csxx
eeprom: at24: platform_data: use BIT() macro
eeprom: at24: split at24_eeprom_write() into specialized functions
eeprom: at24: split at24_eeprom_read() into specialized functions
eeprom: at24: hide the read/write loop behind a macro
eeprom: at24: call read/write functions via function pointers
eeprom: at24: coding style fixes
eeprom: at24: move at24_read() below at24_eeprom_write()
...
Quite a lot of cleanup and maintainence work going on this release in
various drivers, and also a fix for a nasty locking issue in the core:
- A fix for locking issues when external drivers explicitly locked the
bus with spi_bus_lock() - we were using the same lock to both control
access to the physical bus in multi-threaded I/O operations and
exclude multiple callers. Confusion between these two caused us to
have scenarios where we were dropping locks. These are fixed by
splitting into two separate locks like should have been done
originally, making everything much clearer and correct.
- Support for DMA in spi_flash_read().
- Support for instantiating spidev on ACPI systems, including some test
devices used in Windows validation.
- Use of the core DMA mapping functionality in the McSPI driver.
- Start of support for ThunderX SPI controllers, involving a very big
set of changes to the Cavium driver.
- Support for Braswell, Exynos 5433, Kaby Lake, Merrifield, RK3036,
RK3228, RK3368 controllers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXmPFBAAoJECTWi3JdVIfQbisH/355nT/cyqc08l9iC+a1zRDw
/Bf5kN8pqmu6+y3sMjAIdptZQTlXhgR4q1ZH+oNSfowCVgvJYWF6RVCEXDBh6XHs
YBQAFlYeSOO5cLTPQSDnn06oFucV/HZJppC6hM0SNclbVboeMBBS6S6aljXqMbj+
mFvtq6/iEsG6kgQcmcl3fm/SMOYF2OFDJyr66NimBXQGzjx84xJcG0eGk8kCIwEw
xyiE/WmB9WT2scFSgAsfaOEE27ozaq9iANNUA/ceUibQgQYpQveBgy4XVXFjEzFo
3BVvPYGGzjebzaXbMwDV6OvSgMwnTsMxjtZGsraxIEOcMdeeMEpn1/Ze4ksWi4c=
=R4Zx
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of cleanup and maintainence work going on this release in
various drivers, and also a fix for a nasty locking issue in the core:
- A fix for locking issues when external drivers explicitly locked
the bus with spi_bus_lock() - we were using the same lock to both
control access to the physical bus in multi-threaded I/O operations
and exclude multiple callers.
Confusion between these two caused us to have scenarios where we
were dropping locks. These are fixed by splitting into two
separate locks like should have been done originally, making
everything much clearer and correct.
- Support for DMA in spi_flash_read().
- Support for instantiating spidev on ACPI systems, including some
test devices used in Windows validation.
- Use of the core DMA mapping functionality in the McSPI driver.
- Start of support for ThunderX SPI controllers, involving a very big
set of changes to the Cavium driver.
- Support for Braswell, Exynos 5433, Kaby Lake, Merrifield, RK3036,
RK3228, RK3368 controllers"
* tag 'spi-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (64 commits)
spi: Split bus and I/O locking
spi: octeon: Split driver into Octeon specific and common parts
spi: octeon: Move include file from arch/mips to drivers/spi
spi: octeon: Put register offsets into a struct
spi: octeon: Store system clock freqency in struct octeon_spi
spi: octeon: Convert driver to use readq()/writeq() functions
spi: pic32-sqi: fixup wait_for_completion_timeout return handling
spi: pic32: fixup wait_for_completion_timeout return handling
spi: rockchip: limit transfers to (64K - 1) bytes
spi: xilinx: Return IRQ_NONE if no interrupts were detected
spi: xilinx: Handle errors from platform_get_irq()
spi: s3c64xx: restore removed comments
spi: s3c64xx: add Exynos5433 compatible for ioclk handling
spi: s3c64xx: use error code from clk_prepare_enable()
spi: s3c64xx: rename goto labels to meaningful names
spi: s3c64xx: document the clocks and the clock-name property
spi: s3c64xx: add exynos5433 spi compatible
spi: s3c64xx: fix reference leak to master in s3c64xx_spi_remove()
spi: spi-sh: Remove deprecated create_singlethread_workqueue
spi: spi-topcliff-pch: Remove deprecated create_singlethread_workqueue
...
- LED driver for TI LP3952 6-Channel Color LED
LED core improvements:
- Only descend into leds directory when CONFIG_NEW_LEDS is set
- Add no-op gpio_led_register_device when LED subsystem is disabled
- MAINTAINERS: Add file patterns for led device tree bindings
LED Trigger core improvements:
- return error if invalid trigger name is provided via sysfs
LED class drivers improvements
- is31fl32xx: define complete i2c_device_id table
- is31fl32xx: fix typo in id and match table names
- leds-gpio: Set of_node for created LED devices
- pca9532: Add device tree support
Conversion of IDE trigger to common disk trigger:
- leds: convert IDE trigger to common disk trigger
- leds: documentation: 'ide-disk' to 'disk-activity'
- unicore32: use the new LED disk activity trigger
- parisc: use the new LED disk activity trigger
- mips: use the new LED disk activity trigger
- arm: use the new LED disk activity trigger
- powerpc: use the new LED disk activity trigger
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.17 (GNU/Linux)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=8lmX
-----END PGP SIGNATURE-----
Merge tag 'leds_for_4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"New LED class driver:
- LED driver for TI LP3952 6-Channel Color LED
LED core improvements:
- Only descend into leds directory when CONFIG_NEW_LEDS is set
- Add no-op gpio_led_register_device when LED subsystem is disabled
- MAINTAINERS: Add file patterns for led device tree bindings
LED Trigger core improvements:
- return error if invalid trigger name is provided via sysfs
LED class drivers improvements
- is31fl32xx: define complete i2c_device_id table
- is31fl32xx: fix typo in id and match table names
- leds-gpio: Set of_node for created LED devices
- pca9532: Add device tree support
Conversion of IDE trigger to common disk trigger:
- leds: convert IDE trigger to common disk trigger
- leds: documentation: 'ide-disk' to 'disk-activity'
- unicore32: use the new LED disk activity trigger
- parisc: use the new LED disk activity trigger
- mips: use the new LED disk activity trigger
- arm: use the new LED disk activity trigger
- powerpc: use the new LED disk activity trigger"
* tag 'leds_for_4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: is31fl32xx: define complete i2c_device_id table
leds: is31fl32xx: fix typo in id and match table names
leds: LED driver for TI LP3952 6-Channel Color LED
leds: leds-gpio: Set of_node for created LED devices
leds: triggers: return error if invalid trigger name is provided via sysfs
leds: Only descend into leds directory when CONFIG_NEW_LEDS is set
leds: Add no-op gpio_led_register_device when LED subsystem is disabled
unicore32: use the new LED disk activity trigger
parisc: use the new LED disk activity trigger
mips: use the new LED disk activity trigger
arm: use the new LED disk activity trigger
powerpc: use the new LED disk activity trigger
leds: documentation: 'ide-disk' to 'disk-activity'
leds: convert IDE trigger to common disk trigger
leds: pca9532: Add device tree support
MAINTAINERS: Add file patterns for led device tree bindings
* Minor cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXlbvGAAoJEBLB8Bhh3lVK9g0P/16Z5/WIqrrLjJegcZ3qKb4m
u2b5FBwbTDQyj/smZmfZfhZUleO7HDayL188fHPKO11my+Mvjyws8IZCvHshy7+3
b6Krno8NXZuNYtm32srSQQoLE4eN5pookOPMe2KJcRFghwnDqOo0ZfMZ8Lt6RVGg
YtqiVZ3DwaqoHUbvxkHvdJuMbtVEZIEC6SzK9t4URmdncAx+3/BTLqDSYc4LaL+B
tI6REgMy+QT1IUMImuUbOA5ktd78K+D26YKF9NuTSWNQvwzjSYy4y6WmDsjYpZF6
h6YWgGwERIy6gws5IdvkBMKX0s1RV7/sY6xFBsEQrX+IFywyY5OcI1gPRttD6VAn
ORJ4j7WNH8Phqld9YxjEX8yTwGxlxge88J/lb0i9s5jXPMX7ioxAqAjdpsJj6PlA
sNDP0fTyCECqME73cWaAS9bdrzB2dgOxEDfcWKWR24vZeHfnh72owD1k+J0iWu9c
0R2usPB1Yjbo6ODGpqG1R+u09LR+RpNe38oT5GcsFrj6/EaGz0kn2QulaNtylsDo
J5qkm02X1h3+F8/UHrzKavOGk82IQzLCbcW7eHPmyzkH8PTe1semLk9jHnXN5sK3
uL2nirZQVIF6QLbYxf0Uf2oSVs05xc7u9ZT+QOl6hqh/6/K7DWC45SoABwMXDaHH
jXr+y4vtr5IR8GQfZ/nd
=mdxx
-----END PGP SIGNATURE-----
Merge tag 'edac_for_4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC updates from Borislav Petkov:
"This last cycle, Thor was busy adding Arria10 eth FIFO support to the
altera_edac driver along with other improvements. We have two
cleanups/fixes too.
Summary:
- Altera Arria10 ethernet FIFO buffer support (Thor Thayer)
- Minor cleanups"
* tag 'edac_for_4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
ARM: dts: Add Arria10 Ethernet EDAC devicetree entry
EDAC, altera: Add Arria10 Ethernet EDAC support
EDAC, altera: Add Arria10 ECC memory init functions
Documentation: dt: socfpga: Add Arria10 Ethernet binding
EDAC, altera: Drop some ifdeffery
EDAC, altera: Add panic flag check to A10 IRQ
EDAC, altera: Check parent status for Arria10 EDAC block
EDAC, altera: Make all private data structures static
EDAC: Correct channel count limit
EDAC, amd64_edac: Init opstate at the proper time during init
EDAC, altera: Handle Arria10 SDRAM child node
EDAC, altera: Add ECC Manager IRQ controller support
Documentation: dt: socfpga: Add interrupt-controller to ecc-manager
Pull networking updates from David Miller:
1) Unified UDP encapsulation offload methods for drivers, from
Alexander Duyck.
2) Make DSA binding more sane, from Andrew Lunn.
3) Support QCA9888 chips in ath10k, from Anilkumar Kolli.
4) Several workqueue usage cleanups, from Bhaktipriya Shridhar.
5) Add XDP (eXpress Data Path), essentially running BPF programs on RX
packets as soon as the device sees them, with the option to mirror
the packet on TX via the same interface. From Brenden Blanco and
others.
6) Allow qdisc/class stats dumps to run lockless, from Eric Dumazet.
7) Add VLAN support to b53 and bcm_sf2, from Florian Fainelli.
8) Simplify netlink conntrack entry layout, from Florian Westphal.
9) Add ipv4 forwarding support to mlxsw spectrum driver, from Ido
Schimmel, Yotam Gigi, and Jiri Pirko.
10) Add SKB array infrastructure and convert tun and macvtap over to it.
From Michael S Tsirkin and Jason Wang.
11) Support qdisc packet injection in pktgen, from John Fastabend.
12) Add neighbour monitoring framework to TIPC, from Jon Paul Maloy.
13) Add NV congestion control support to TCP, from Lawrence Brakmo.
14) Add GSO support to SCTP, from Marcelo Ricardo Leitner.
15) Allow GRO and RPS to function on macsec devices, from Paolo Abeni.
16) Support MPLS over IPV4, from Simon Horman.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
xgene: Fix build warning with ACPI disabled.
be2net: perform temperature query in adapter regardless of its interface state
l2tp: Correctly return -EBADF from pppol2tp_getname.
net/mlx5_core/health: Remove deprecated create_singlethread_workqueue
net: ipmr/ip6mr: update lastuse on entry change
macsec: ensure rx_sa is set when validation is disabled
tipc: dump monitor attributes
tipc: add a function to get the bearer name
tipc: get monitor threshold for the cluster
tipc: make cluster size threshold for monitoring configurable
tipc: introduce constants for tipc address validation
net: neigh: disallow transition to NUD_STALE if lladdr is unchanged in neigh_update()
MAINTAINERS: xgene: Add driver and documentation path
Documentation: dtb: xgene: Add MDIO node
dtb: xgene: Add MDIO node
drivers: net: xgene: ethtool: Use phy_ethtool_gset and sset
drivers: net: xgene: Use exported functions
drivers: net: xgene: Enable MDIO driver
drivers: net: xgene: Add backward compatibility
drivers: net: phy: xgene: Add MDIO driver
...
- ACPI support for guests on ARM platforms.
- Generic steal time support for arm and x86.
- Support cases where kernel cpu is not Xen VCPU number (e.g., if
in-guest kexec is used).
- Use the system workqueue instead of a custom workqueue in various
places.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXmLlrAAoJEFxbo/MsZsTRvRQH/1wOMF8BmlbZfR7H3qwDfjst
ApNifCiZE08xDtWBlwUaBFAQxyflQS9BBiNZDVK0sysIdXeOdpWV7V0ZjRoLL+xr
czsaaGXDcmXxJxApoMDVuT7FeP6rEk6LVAYRoHpVjJjMZGW3BbX1vZaMW4DXl2WM
9YNaF2Lj+rpc1f8iG31nUxwkpmcXFog6ct4tu7HiyCFT3hDkHt/a4ghuBdQItCkd
vqBa1pTpcGtQBhSmWzlylN/PV2+NKcRd+kGiwd09/O/rNzogTMCTTWeHKAtMpPYb
Cu6oSqJtlK5o0vtr0qyLSWEGIoyjE2gE92s0wN3iCzFY1PldqdsxUO622nIj+6o=
=G6q3
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.8-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from David Vrabel:
"Features and fixes for 4.8-rc0:
- ACPI support for guests on ARM platforms.
- Generic steal time support for arm and x86.
- Support cases where kernel cpu is not Xen VCPU number (e.g., if
in-guest kexec is used).
- Use the system workqueue instead of a custom workqueue in various
places"
* tag 'for-linus-4.8-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (47 commits)
xen: add static initialization of steal_clock op to xen_time_ops
xen/pvhvm: run xen_vcpu_setup() for the boot CPU
xen/evtchn: use xen_vcpu_id mapping
xen/events: fifo: use xen_vcpu_id mapping
xen/events: use xen_vcpu_id mapping in events_base
x86/xen: use xen_vcpu_id mapping when pointing vcpu_info to shared_info
x86/xen: use xen_vcpu_id mapping for HYPERVISOR_vcpu_op
xen: introduce xen_vcpu_id mapping
x86/acpi: store ACPI ids from MADT for future usage
x86/xen: update cpuid.h from Xen-4.7
xen/evtchn: add IOCTL_EVTCHN_RESTRICT
xen-blkback: really don't leak mode property
xen-blkback: constify instance of "struct attribute_group"
xen-blkfront: prefer xenbus_scanf() over xenbus_gather()
xen-blkback: prefer xenbus_scanf() over xenbus_gather()
xen: support runqueue steal time on xen
arm/xen: add support for vm_assist hypercall
xen: update xen headers
xen-pciback: drop superfluous variables
xen-pciback: short-circuit read path used for merging write values
...
- Kexec support for arm64
- Kprobes support
- Expose MIDR_EL1 and REVIDR_EL1 CPU identification registers to sysfs
- Trapping of user space cache maintenance operations and emulation in
the kernel (CPU errata workaround)
- Clean-up of the early page tables creation (kernel linear mapping, EFI
run-time maps) to avoid splitting larger blocks (e.g. pmds) into
smaller ones (e.g. ptes)
- VDSO support for CLOCK_MONOTONIC_RAW in clock_gettime()
- ARCH_HAS_KCOV enabled for arm64
- Optimise IP checksum helpers
- SWIOTLB optimisation to only allocate/initialise the buffer if the
available RAM is beyond the 32-bit mask
- Properly handle the "nosmp" command line argument
- Fix for the initialisation of the CPU debug state during early boot
- vdso-offsets.h build dependency workaround
- Build fix when RANDOMIZE_BASE is enabled with MODULES off
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iJOY
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- Kexec support for arm64
- Kprobes support
- Expose MIDR_EL1 and REVIDR_EL1 CPU identification registers to sysfs
- Trapping of user space cache maintenance operations and emulation in
the kernel (CPU errata workaround)
- Clean-up of the early page tables creation (kernel linear mapping,
EFI run-time maps) to avoid splitting larger blocks (e.g. pmds) into
smaller ones (e.g. ptes)
- VDSO support for CLOCK_MONOTONIC_RAW in clock_gettime()
- ARCH_HAS_KCOV enabled for arm64
- Optimise IP checksum helpers
- SWIOTLB optimisation to only allocate/initialise the buffer if the
available RAM is beyond the 32-bit mask
- Properly handle the "nosmp" command line argument
- Fix for the initialisation of the CPU debug state during early boot
- vdso-offsets.h build dependency workaround
- Build fix when RANDOMIZE_BASE is enabled with MODULES off
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (64 commits)
arm64: arm: Fix-up the removal of the arm64 regs_query_register_name() prototype
arm64: Only select ARM64_MODULE_PLTS if MODULES=y
arm64: mm: run pgtable_page_ctor() on non-swapper translation table pages
arm64: mm: make create_mapping_late() non-allocating
arm64: Honor nosmp kernel command line option
arm64: Fix incorrect per-cpu usage for boot CPU
arm64: kprobes: Add KASAN instrumentation around stack accesses
arm64: kprobes: Cleanup jprobe_return
arm64: kprobes: Fix overflow when saving stack
arm64: kprobes: WARN if attempting to step with PSTATE.D=1
arm64: debug: remove unused local_dbg_{enable, disable} macros
arm64: debug: remove redundant spsr manipulation
arm64: debug: unmask PSTATE.D earlier
arm64: localise Image objcopy flags
arm64: ptrace: remove extra define for CPSR's E bit
kprobes: Add arm64 case in kprobe example module
arm64: Add kernel return probes support (kretprobes)
arm64: Add trampoline code for kretprobes
arm64: kprobes instruction simulation support
arm64: Treat all entry code as non-kprobe-able
...
replacing redundant inode page updates with mark_inode_dirty calls. And we tried
to reduce lock contentions as well to improve filesystem scalability.
Other feature is setting F2FS automatically when detecting host-managed SMR.
= Enhancement =
- ioctl to move a range of data between files
- inject orphan inode errors
- avoid flush commands congestion
- support lazytime
= Bug fixes =
- return proper results for some dentry operations
- fix deadlock in add_link failure
- disable extent_cache for fcollapse/finsert
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tKTR
-----END PGP SIGNATURE-----
Merge tag 'for-f2fs-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs updates from Jaegeuk Kim:
"The major change in this version is mitigating cpu overheads on write
paths by replacing redundant inode page updates with mark_inode_dirty
calls. And we tried to reduce lock contentions as well to improve
filesystem scalability. Other feature is setting F2FS automatically
when detecting host-managed SMR.
Enhancements:
- ioctl to move a range of data between files
- inject orphan inode errors
- avoid flush commands congestion
- support lazytime
Bug fixes:
- return proper results for some dentry operations
- fix deadlock in add_link failure
- disable extent_cache for fcollapse/finsert"
* tag 'for-f2fs-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (68 commits)
f2fs: clean up coding style and redundancy
f2fs: get victim segment again after new cp
f2fs: handle error case with f2fs_bug_on
f2fs: avoid data race when deciding checkpoin in f2fs_sync_file
f2fs: support an ioctl to move a range of data blocks
f2fs: fix to report error number of f2fs_find_entry
f2fs: avoid memory allocation failure due to a long length
f2fs: reset default idle interval value
f2fs: use blk_plug in all the possible paths
f2fs: fix to avoid data update racing between GC and DIO
f2fs: add maximum prefree segments
f2fs: disable extent_cache for fcollapse/finsert inodes
f2fs: refactor __exchange_data_block for speed up
f2fs: fix ERR_PTR returned by bio
f2fs: avoid mark_inode_dirty
f2fs: move i_size_write in f2fs_write_end
f2fs: fix to avoid redundant discard during fstrim
f2fs: avoid mismatching block range for discard
f2fs: fix incorrect f_bfree calculation in ->statfs
f2fs: use percpu_rw_semaphore
...
* topic/docs-next: (322 commits)
[media] cx23885-cardlist.rst: add a new card
[media] doc-rst: add some needed escape codes
[media] doc-rst: kapi: use :c:func: instead of :cpp:func
doc-rst: kernel-doc: fix a change introduced by mistake
[media] v4l2-ioctl.h add debug info for struct v4l2_ioctl_ops
[media] dvb_ringbuffer.h: some documentation improvements
[media] v4l2-ctrls.h: fully document the header file
[media] doc-rst: Fix some typedef ugly warnings
[media] doc-rst: reorganize the kAPI v4l2 chapters
[media] rename v4l2-framework.rst to v4l2-intro.rst
[media] move V4L2 clocks to a separate .rst file
[media] v4l2-fh.rst: add cross references and markups
[media] v4l2-fh.rst: add fh contents from v4l2-framework.rst
[media] v4l2-fh.h: add documentation for it
[media] v4l2-event.rst: add cross-references and markups
[media] v4l2-event.h: document all functions
[media] v4l2-event.rst: add text from v4l2-framework.rst
[media] v4l2-framework.rst: remove videobuf quick chapter
[media] v4l2-dev: add cross-references and improve markup
[media] doc-rst: move v4l2-dev doc to a separate file
...
Merge updates from Andrew Morton:
- a few misc bits
- ocfs2
- most(?) of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (125 commits)
thp: fix comments of __pmd_trans_huge_lock()
cgroup: remove unnecessary 0 check from css_from_id()
cgroup: fix idr leak for the first cgroup root
mm: memcontrol: fix documentation for compound parameter
mm: memcontrol: remove BUG_ON in uncharge_list
mm: fix build warnings in <linux/compaction.h>
mm, thp: convert from optimistic swapin collapsing to conservative
mm, thp: fix comment inconsistency for swapin readahead functions
thp: update Documentation/{vm/transhuge,filesystems/proc}.txt
shmem: split huge pages beyond i_size under memory pressure
thp: introduce CONFIG_TRANSPARENT_HUGE_PAGECACHE
khugepaged: add support of collapse for tmpfs/shmem pages
shmem: make shmem_inode_info::lock irq-safe
khugepaged: move up_read(mmap_sem) out of khugepaged_alloc_page()
thp: extract khugepaged from mm/huge_memory.c
shmem, thp: respect MADV_{NO,}HUGEPAGE for file mappings
shmem: add huge pages support
shmem: get_unmapped_area align huge page
shmem: prepare huge= mount option and sysfs knob
mm, rmap: account shmem thp pages
...
* introduce reboot mode driver
* add DT support to max8903
* add power supply support for axp221
* misc. fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bMvA
-----END PGP SIGNATURE-----
Merge tag 'for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
- introduce reboot mode driver
- add DT support to max8903
- add power supply support for axp221
- misc fixes
* tag 'for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
power: reset: add reboot mode driver
dt-bindings: power: reset: add document for reboot-mode driver
power_supply: fix return value of get_property
power: qcom_smbb: Make an extcon for usb cable detection
max8903: adds support for initiation via device tree
max8903: adds documentation for device tree bindings.
max8903: remove unnecessary 'out of memory' error message.
max8903: removes non zero validity checks on gpios.
max8903: adds requesting of gpios.
max8903: cleans up confusing relationship between dc_valid, dok and dcm.
max8903: store pointer to pdata instead of copying it.
power_supply: bq27xxx_battery: Group register mappings into one table
docs: Move brcm,bcm21664-resetmgr.txt
power/reset: make syscon_poweroff() static
power: axp20x_usb: Add support for usb power-supply on axp22x pmics
power_supply: bq27xxx_battery: Index register numbers by enum
power_supply: bq27xxx_battery: Fix copy/paste error in header comment
MAINTAINERS: Add file patterns for power supply device tree bindings
power: reset: keystone: Enable COMPILE_TEST
A quiet regulator API release, a few new drivers and some fixes but
nothing too notable. There will also be some updates for the PWM
regulator coming through the PWM tree which provide much smoother
operation when taking over an already running PWM regulator after boot
using some new PWM APIs.
- Support for configuration of the initial suspend state from DT.
- New drivers for Mediatek MT6323, Ricoh RN5T567 and X-Powers AXP809.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXlk49AAoJECTWi3JdVIfQM4QH/jg2BGgdQSiuQspidmyN9tpL
hZgvUzrKm0eXEvzvTaL4cPymqpDHgQgaWEFo3Kv2WiU+34XIzfKPTt8m0WI37HY9
t4rTMlN8vL4WEMtAlB0i4DH1/jcEOJG2c88+tnSBGb5R8AXXIvx+F9xjWxOoJKJY
ccf5QcupDfCJw99rs3Li5eIbHOW2RAcZgurGGUyV01kH+G/9LliNpIKa9uCxK4dw
72aMH6QX+Hjid4UAqwL13C5W3sBDSebYYTwtTW61HosydLv818BfZC8IoezgjBRE
unjh6kdxOpcZk0ftciNiNQFLTUhobdYAuQFjUZywNqijpqK28lbFypweP8yhoxg=
=rDhl
-----END PGP SIGNATURE-----
Merge tag 'regulator-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"A quiet regulator API release, a few new drivers and some fixes but
nothing too notable. There will also be some updates for the PWM
regulator coming through the PWM tree which provide much smoother
operation when taking over an already running PWM regulator after boot
using some new PWM APIs.
Summary:
- Support for configuration of the initial suspend state from DT.
- New drivers for Mediatek MT6323, Ricoh RN5T567 and X-Powers AXP809"
* tag 'regulator-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (38 commits)
regulator: da9053/52: Fix incorrectly stated minimum and maximum voltage limits
regulator: mt6323: Constify struct regulator_ops
regulator: mt6323: Fix module description
regulator: mt6323: Add support for MT6323 regulator
regulator: Add document for MT6323 regulator
regulator: da9210: addition of device tree support
regulator: act8865: Fix missing of_node_put() in act8865_pdata_from_dt()
regulator: qcom_smd: Avoid overlapping linear voltage ranges
regulator: s2mps11: Fix the voltage linear range for s2mps15
regulator: pwm: Fix regulator ramp delay for continuous mode
regulator: da9211: add descriptions for da9212/da9214
mfd: rn5t618: Register restart handler
mfd: rn5t618: Register power off callback optionally
regulator: rn5t618: Add RN5T567 PMIC support
mfd: rn5t618: Add Ricoh RN5T567 PMIC support
ARM: dts: meson: minix-neo-x8: define PMIC as power controller
regulator: tps65218: force set power-up/down strobe to 3 for dcdc3
regulator: tps65218: Enable suspend configuration
regulator: tps65217: Enable suspend configuration
regulator: qcom_spmi: Add support for get_mode/set_mode on switches
...
Core changes:
- The big item is of course the completion of the character
device ABI. It has now replaced and surpassed the former
unmaintainable sysfs ABI: we can now hammer (bitbang)
individual lines or sets of lines and read individual lines
or sets of lines from userspace, and we can also register
to listen to GPIO events from userspace. As a tie-in we
have two new tools in tools/gpio: gpio-hammer and
gpio-event-mon that illustrate the proper use of the new
ABI. As someone said: the wild west days of GPIO are now
over.
- Continued to remove the pointless
ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB Kconfig symbols.
I'm patching hexagon, openrisc, powerpc, sh, unicore,
ia64 and microblaze. These are either ACKed by their
maintainers or patched anyways after a grace period and
no response from maintainers. Some archs (ARM) come in from
their trees, and others (x86) are still not fixed, so I
might send a second pull request to root it out later in
this merge window, or just defer to v4.9.
- The GPIO tools are moved to the tools build system.
New drivers:
- New driver for the MAX77620/MAX20024.
- New driver for the Intel Merrifield.
- Enabled PCA953x for the TI PCA9536.
- Enabled PCA953x for the Intel Edison.
- Enabled R8A7792 in the RCAR driver.
Driver improvements:
- The STMPE and F7188x now supports the .get_direction()
callback.
- The Xilinx driver supports setting multiple lines at
once.
- ACPI support for the Vulcan GPIO controller.
- The MMIO GPIO driver supports device tree probing.
- The Acer One 10 is supported through the _DEP ACPI
attribute.
Cleanups:
- A major cleanup of the OF/DT support code. It is way
easier to read and understand now, probably this improves
performance too.
- Drop a few redundant .owner assignments.
- Remove CLPS711x boardfile support: we are 100% DT.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NwcK
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.8 kernel cycle. The big
news is the completion of the chardev ABI which I'm very happy about
and apart from that it's an ordinary, quite busy cycle. The details
are below.
The patches are tested in linux-next for some time, patches to other
subsystem mostly have ACKs.
I got overly ambitious with configureing lines as input for IRQ lines
but it turns out that some controllers have their interrupt-enable and
input-enabling in orthogonal settings so the assumption that all IRQ
lines are input lines does not hold. Oh well, revert and back to the
drawing board with that.
Core changes:
- The big item is of course the completion of the character device
ABI. It has now replaced and surpassed the former unmaintainable
sysfs ABI: we can now hammer (bitbang) individual lines or sets of
lines and read individual lines or sets of lines from userspace,
and we can also register to listen to GPIO events from userspace.
As a tie-in we have two new tools in tools/gpio: gpio-hammer and
gpio-event-mon that illustrate the proper use of the new ABI. As
someone said: the wild west days of GPIO are now over.
- Continued to remove the pointless ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
Kconfig symbols. I'm patching hexagon, openrisc, powerpc, sh,
unicore, ia64 and microblaze. These are either ACKed by their
maintainers or patched anyways after a grace period and no response
from maintainers.
Some archs (ARM) come in from their trees, and others (x86) are
still not fixed, so I might send a second pull request to root it
out later in this merge window, or just defer to v4.9.
- The GPIO tools are moved to the tools build system.
New drivers:
- New driver for the MAX77620/MAX20024.
- New driver for the Intel Merrifield.
- Enabled PCA953x for the TI PCA9536.
- Enabled PCA953x for the Intel Edison.
- Enabled R8A7792 in the RCAR driver.
Driver improvements:
- The STMPE and F7188x now supports the .get_direction() callback.
- The Xilinx driver supports setting multiple lines at once.
- ACPI support for the Vulcan GPIO controller.
- The MMIO GPIO driver supports device tree probing.
- The Acer One 10 is supported through the _DEP ACPI attribute.
Cleanups:
- A major cleanup of the OF/DT support code. It is way easier to
read and understand now, probably this improves performance too.
- Drop a few redundant .owner assignments.
- Remove CLPS711x boardfile support: we are 100% DT"
* tag 'gpio-v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (67 commits)
MAINTAINERS: Add INTEL MERRIFIELD GPIO entry
gpio: dwapb: add missing fwnode_handle_put() in dwapb_gpio_get_pdata()
gpio: merrifield: Protect irq_ack() and gpio_set() by lock
gpio: merrifield: Introduce GPIO driver to support Merrifield
gpio: intel-mid: Make it depend to X86_INTEL_MID
gpio: intel-mid: Sort header block alphabetically
gpio: intel-mid: Remove potentially harmful code
gpio: rcar: add R8A7792 support
gpiolib: remove duplicated include from gpiolib.c
Revert "gpio: convince line to become input in irq helper"
gpiolib: of_find_gpio(): Don't discard errors
gpio: of: Allow overriding the device node
gpio: free handles in fringe cases
gpio: tps65218: Add platform_device_id table
gpio: max77620: get gpio value based on direction
gpio: lynxpoint: avoid potential warning on error path
tools/gpio: add install section
tools/gpio: move to tools buildsystem
gpio: intel-mid: switch to devm_gpiochip_add_data()
gpio: 74x164: Use spi_write() helper instead of open coding
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXlfJvAAoJEAhfPr2O5OEVtLUP/RpCQ+W3YVryIdmLkdmYXoY7
m2rXtUh7GmzBjaBkFzbRCGZtgROF7zl0e1R3nm4tLbCV4Becw8HO7YiMjqFJm9xr
b6IngIyshsHf60Eii3RpLqUFvYrc/DDIMeYf8miwj/PvFAfI2BV9apraexJlpUuI
wdyi28cfBHq4WYhubaXKoAyBQ8YRA/t8KNRAkDlifaOaMbSAxWHlmqoSmJWeQx73
KHkSvbRPu4Hjo3R6q/ab8VhqmXeSnbqnQB9lgnxz7AmAZGhOlMYeAhV/K2ZwbBH8
swv36RmJVO59Ov+vNR4p7GGGDL3+qk8JLj4LNVVfOcW0A+t7WrPQEmrL6VsyaZAy
/+r4NEOcQN6Z5nFwbr3E0tYJ2Y5jFHOvsBfKd3EEGwty+hCl634akgb0vqtg06cg
E2KG+XW983RBadVwEBnEudxJb0fWPWHGhXEqRrwOD+718FNmTqYM6dEvTEyxRup8
EtCLj+eQQ4LmAyZxWyE8A+keKoMFQlHqk9LN9vQ7t7Wxq9mQ+V2l12T/lN4VhdTq
4QZ4mrCMCGEvNcNzgSg6R/9lVb6RHDtMXZ3htbB/w+5xET/IKIANYyg1Hr7ahtdh
rTW/4q6n3jtsu6tp5poteFvPzZKAblbrj2EptVzZYkonQ5BeAUisFTtneUL10Jmj
EUf/sH0fqoOA0VvV6Tu+
=mrOW
-----END PGP SIGNATURE-----
Merge tag 'media/v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new framework support for HDMI CEC and remote control support
- new encoding codec driver for Mediatek SoC
- new frontend driver: helene tuner
- added support for NetUp almost universal devices, with supports
DVB-C/S/S2/T/T2 and ISDB-T
- the mn88472 frontend driver got promoted from staging
- a new driver for RCar video input
- some soc_camera legacy drivers got removed: timb, omap1, mx2, mx3
- lots of driver cleanups, improvements and fixups
* tag 'media/v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (377 commits)
[media] cec: always check all_device_types and features
[media] cec: poll should check if there is room in the tx queue
[media] vivid: support monitor all mode
[media] cec: fix test for unconfigured adapter in main message loop
[media] cec: limit the size of the transmit queue
[media] cec: zero unused msg part after msg->len
[media] cec: don't set fh to NULL in CEC_TRANSMIT
[media] cec: clear all status fields before transmit and always fill in sequence
[media] cec: CEC_RECEIVE overwrote the timeout field
[media] cxd2841er: Reading SNR for DVB-C added
[media] cxd2841er: Reading BER and UCB for DVB-C added
[media] cxd2841er: fix switch-case for DVB-C
[media] cxd2841er: fix signal strength scale for ISDB-T
[media] cxd2841er: adjust the dB scale for DVB-C
[media] cxd2841er: provide signal strength for DVB-C
[media] cxd2841er: fix BER report via DVBv5 stats API
[media] mb86a20s: apply mask to val after checking for read failure
[media] airspy: fix error logic during device register
[media] s5p-cec/TODO: add TODO item
[media] cec/TODO: drop comment about sphinx documentation
...
- Support for ACPI SSDT overlays allowing Secondary System
Description Tables (SSDTs) to be loaded at any time from EFI
variables or via configfs (Octavian Purdila, Mika Westerberg).
- Support for the ACPI LPI (Low-Power Idle) feature introduced in
ACPI 6.0 and allowing processor idle states to be represented in
ACPI tables in a hierarchical way (with the help of Processor
Container objects) and support for ACPI idle states management
on ARM64, based on LPI (Sudeep Holla).
- General improvements of ACPI support for NUMA and ARM64 support
for ACPI-based NUMA (Hanjun Guo, David Daney, Robert Richter).
- General improvements of the ACPI table upgrade mechanism and
ARM64 support for that feature (Aleksey Makarov, Jon Masters).
- Support for the Boot Error Record Table (BERT) in APEI and
improvements of kernel messages printed by the error injection
code (Huang Ying, Borislav Petkov).
- New driver for the Intel Broxton WhiskeyCove PMIC operation
region and support for the REGS operation region on Broxton,
PMIC code cleanups (Bin Gao, Felipe Balbi, Paul Gortmaker).
- New driver for the power participant device which is part of the
Dynamic Power and Thermal Framework (DPTF) and DPTF-related code
reorganization (Srinivas Pandruvada).
- Support for the platform-initiated graceful shutdown feature
introduced in ACPI 6.1 (Prashanth Prakash).
- ACPI button driver update related to lid input events generated
automatically on initialization and system resume that have been
problematic for some time (Lv Zheng).
- ACPI EC driver cleanups (Lv Zheng).
- Documentation of the ACPICA release automation process and the
in-kernel ACPI AML debugger (Lv Zheng).
- New blacklist entry and two fixes for the ACPI backlight driver
(Alex Hung, Arvind Yadav, Ralf Gerbig).
- Cleanups of the ACPI pci_slot driver (Joe Perches, Paul Gortmaker).
- ACPI CPPC code changes to make it more robust against possible
defects in ACPI tables and new symbol definitions for PCC (Hoan
Tran).
- System reboot code modification to execute the ACPI _PTS (Prepare
To Sleep) method in addition to _TTS (Ocean He).
- ACPICA-related change to carry out lock ordering checks in ACPICA
if ACPICA debug is enabled in the kernel (Lv Zheng).
- Assorted minor fixes and cleanups (Andy Shevchenko, Baoquan He,
Bhaktipriya Shridhar, Paul Gortmaker, Rafael Wysocki).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=YwbM
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"The new feaures here are the support for ACPI overlays (allowing ACPI
tables to be loaded at any time from EFI variables or via configfs)
and the LPI (Low-Power Idle) support. Also notable is the ACPI-based
NUMA support for ARM64.
Apart from that we have two new drivers, for the DPTF (Dynamic Power
and Thermal Framework) power participant device and for the Intel
Broxton WhiskeyCove PMIC, some more PMIC-related changes, support for
the Boot Error Record Table (BERT) in APEI and support for
platform-initiated graceful shutdown.
Plus two new pieces of documentation and usual assorted fixes and
cleanups in quite a few places.
Specifics:
- Support for ACPI SSDT overlays allowing Secondary System
Description Tables (SSDTs) to be loaded at any time from EFI
variables or via configfs (Octavian Purdila, Mika Westerberg).
- Support for the ACPI LPI (Low-Power Idle) feature introduced in
ACPI 6.0 and allowing processor idle states to be represented in
ACPI tables in a hierarchical way (with the help of Processor
Container objects) and support for ACPI idle states management on
ARM64, based on LPI (Sudeep Holla).
- General improvements of ACPI support for NUMA and ARM64 support for
ACPI-based NUMA (Hanjun Guo, David Daney, Robert Richter).
- General improvements of the ACPI table upgrade mechanism and ARM64
support for that feature (Aleksey Makarov, Jon Masters).
- Support for the Boot Error Record Table (BERT) in APEI and
improvements of kernel messages printed by the error injection code
(Huang Ying, Borislav Petkov).
- New driver for the Intel Broxton WhiskeyCove PMIC operation region
and support for the REGS operation region on Broxton, PMIC code
cleanups (Bin Gao, Felipe Balbi, Paul Gortmaker).
- New driver for the power participant device which is part of the
Dynamic Power and Thermal Framework (DPTF) and DPTF-related code
reorganization (Srinivas Pandruvada).
- Support for the platform-initiated graceful shutdown feature
introduced in ACPI 6.1 (Prashanth Prakash).
- ACPI button driver update related to lid input events generated
automatically on initialization and system resume that have been
problematic for some time (Lv Zheng).
- ACPI EC driver cleanups (Lv Zheng).
- Documentation of the ACPICA release automation process and the
in-kernel ACPI AML debugger (Lv Zheng).
- New blacklist entry and two fixes for the ACPI backlight driver
(Alex Hung, Arvind Yadav, Ralf Gerbig).
- Cleanups of the ACPI pci_slot driver (Joe Perches, Paul Gortmaker).
- ACPI CPPC code changes to make it more robust against possible
defects in ACPI tables and new symbol definitions for PCC (Hoan
Tran).
- System reboot code modification to execute the ACPI _PTS (Prepare
To Sleep) method in addition to _TTS (Ocean He).
- ACPICA-related change to carry out lock ordering checks in ACPICA
if ACPICA debug is enabled in the kernel (Lv Zheng).
- Assorted minor fixes and cleanups (Andy Shevchenko, Baoquan He,
Bhaktipriya Shridhar, Paul Gortmaker, Rafael Wysocki)"
* tag 'acpi-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (71 commits)
ACPI: enable ACPI_PROCESSOR_IDLE on ARM64
arm64: add support for ACPI Low Power Idle(LPI)
drivers: firmware: psci: initialise idle states using ACPI LPI
cpuidle: introduce CPU_PM_CPU_IDLE_ENTER macro for ARM{32, 64}
arm64: cpuidle: drop __init section marker to arm_cpuidle_init
ACPI / processor_idle: Add support for Low Power Idle(LPI) states
ACPI / processor_idle: introduce ACPI_PROCESSOR_CSTATE
ACPI / DPTF: move int340x_thermal.c to the DPTF folder
ACPI / DPTF: Add DPTF power participant driver
ACPI / lpat: make it explicitly non-modular
ACPI / dock: make dock explicitly non-modular
ACPI / PCI: make pci_slot explicitly non-modular
ACPI / PMIC: remove modular references from non-modular code
ACPICA: Linux: Enable ACPI_MUTEX_DEBUG for Linux kernel
ACPI: Rename configfs.c to acpi_configfs.c to prevent link error
ACPI / debugger: Add AML debugger documentation
ACPI: Add documentation describing ACPICA release automation
ACPI: add support for loading SSDTs via configfs
ACPI: add support for configfs
efi / ACPI: load SSTDs from EFI variables
...
- Rework the cpufreq governor interface to make it more straightforward
and modify the conservative governor to avoid using transition
notifications (Rafael Wysocki).
- Rework the handling of frequency tables by the cpufreq core to make
it more efficient (Viresh Kumar).
- Modify the schedutil governor to reduce the number of wakeups it
causes to occur in cases when the CPU frequency doesn't need to be
changed (Steve Muckle, Viresh Kumar).
- Fix some minor issues and clean up code in the cpufreq core and
governors (Rafael Wysocki, Viresh Kumar).
- Add Intel Broxton support to the intel_pstate driver (Srinivas
Pandruvada).
- Fix problems related to the config TDP feature and to the validity
of the MSR_HWP_INTERRUPT register in intel_pstate (Jan Kiszka,
Srinivas Pandruvada).
- Make intel_pstate update the cpu_frequency tracepoint even if
the frequency doesn't change to avoid confusing powertop (Rafael
Wysocki).
- Clean up the usage of __init/__initdata in intel_pstate, mark some
of its internal variables as __read_mostly and drop an unused
structure element from it (Jisheng Zhang, Carsten Emde).
- Clean up the usage of some duplicate MSR symbols in intel_pstate
and turbostat (Srinivas Pandruvada).
- Update/fix the powernv, s3c24xx and mvebu cpufreq drivers (Akshay
Adiga, Viresh Kumar, Ben Dooks).
- Fix a regression (introduced during the 4.5 cycle) in the
pcc-cpufreq driver by reverting the problematic commit (Andreas
Herrmann).
- Add support for Intel Denverton to intel_idle, clean up Broxton
support in it and make it explicitly non-modular (Jacob Pan,
Jan Beulich, Paul Gortmaker).
- Add support for Denverton and Ivy Bridge server to the Intel RAPL
power capping driver and make it more careful about the handing
of MSRs that may not be present (Jacob Pan, Xiaolong Wang).
- Fix resume from hibernation on x86-64 by making the CPU offline
during resume avoid using MONITOR/MWAIT in the "play dead" loop
which may lead to an inadvertent "revival" of a "dead" CPU and
a page fault leading to a kernel crash from it (Rafael Wysocki).
- Make memory management during resume from hibernation more
straightforward (Rafael Wysocki).
- Add debug features that should help to detect problems related
to hibernation and resume from it (Rafael Wysocki, Chen Yu).
- Clean up hibernation core somewhat (Rafael Wysocki).
- Prevent KASAN from instrumenting the hibernation core which leads
to large numbers of false-positives from it (James Morse).
- Prevent PM (hibernate and suspend) notifiers from being called
during the cleanup phase if they have not been called during the
corresponding preparation phase which is possible if one of the
other notifiers returns an error at that time (Lianwei Wang).
- Improve suspend-related debug printout in the tasks freezer and
clean up suspend-related console handling (Roger Lu, Borislav
Petkov).
- Update the AnalyzeSuspend script in the kernel sources to
version 4.2 (Todd Brandt).
- Modify the generic power domains framework to make it handle
system suspend/resume better (Ulf Hansson).
- Make the runtime PM framework avoid resuming devices synchronously
when user space changes the runtime PM settings for them and
improve its error reporting (Rafael Wysocki, Linus Walleij).
- Fix error paths in devfreq drivers (exynos, exynos-ppmu, exynos-bus)
and in the core, make some devfreq code explicitly non-modular and
change some of it into tristate (Bartlomiej Zolnierkiewicz,
Peter Chen, Paul Gortmaker).
- Add DT support to the generic PM clocks management code and make
it export some more symbols (Jon Hunter, Paul Gortmaker).
- Make the PCI PM core code slightly more robust against possible
driver errors (Andy Shevchenko).
- Make it possible to change DESTDIR and PREFIX in turbostat
(Andy Shevchenko).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=uVGz
-----END PGP SIGNATURE-----
Merge tag 'pm-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"Again, the majority of changes go into the cpufreq subsystem, but
there are no big features this time. The cpufreq changes that stand
out somewhat are the governor interface rework and improvements
related to the handling of frequency tables. Apart from those, there
are fixes and new device/CPU IDs in drivers, cleanups and an
improvement of the new schedutil governor.
Next, there are some changes in the hibernation core, including a fix
for a nasty problem related to the MONITOR/MWAIT usage by CPU offline
during resume from hibernation, a few core improvements related to
memory management during resume, a couple of additional debug features
and cleanups.
Finally, we have some fixes and cleanups in the devfreq subsystem,
generic power domains framework improvements related to system
suspend/resume, support for some new chips in intel_idle and in the
power capping RAPL driver, a new version of the AnalyzeSuspend utility
and some assorted fixes and cleanups.
Specifics:
- Rework the cpufreq governor interface to make it more
straightforward and modify the conservative governor to avoid using
transition notifications (Rafael Wysocki).
- Rework the handling of frequency tables by the cpufreq core to make
it more efficient (Viresh Kumar).
- Modify the schedutil governor to reduce the number of wakeups it
causes to occur in cases when the CPU frequency doesn't need to be
changed (Steve Muckle, Viresh Kumar).
- Fix some minor issues and clean up code in the cpufreq core and
governors (Rafael Wysocki, Viresh Kumar).
- Add Intel Broxton support to the intel_pstate driver (Srinivas
Pandruvada).
- Fix problems related to the config TDP feature and to the validity
of the MSR_HWP_INTERRUPT register in intel_pstate (Jan Kiszka,
Srinivas Pandruvada).
- Make intel_pstate update the cpu_frequency tracepoint even if the
frequency doesn't change to avoid confusing powertop (Rafael
Wysocki).
- Clean up the usage of __init/__initdata in intel_pstate, mark some
of its internal variables as __read_mostly and drop an unused
structure element from it (Jisheng Zhang, Carsten Emde).
- Clean up the usage of some duplicate MSR symbols in intel_pstate
and turbostat (Srinivas Pandruvada).
- Update/fix the powernv, s3c24xx and mvebu cpufreq drivers (Akshay
Adiga, Viresh Kumar, Ben Dooks).
- Fix a regression (introduced during the 4.5 cycle) in the
pcc-cpufreq driver by reverting the problematic commit (Andreas
Herrmann).
- Add support for Intel Denverton to intel_idle, clean up Broxton
support in it and make it explicitly non-modular (Jacob Pan, Jan
Beulich, Paul Gortmaker).
- Add support for Denverton and Ivy Bridge server to the Intel RAPL
power capping driver and make it more careful about the handing of
MSRs that may not be present (Jacob Pan, Xiaolong Wang).
- Fix resume from hibernation on x86-64 by making the CPU offline
during resume avoid using MONITOR/MWAIT in the "play dead" loop
which may lead to an inadvertent "revival" of a "dead" CPU and a
page fault leading to a kernel crash from it (Rafael Wysocki).
- Make memory management during resume from hibernation more
straightforward (Rafael Wysocki).
- Add debug features that should help to detect problems related to
hibernation and resume from it (Rafael Wysocki, Chen Yu).
- Clean up hibernation core somewhat (Rafael Wysocki).
- Prevent KASAN from instrumenting the hibernation core which leads
to large numbers of false-positives from it (James Morse).
- Prevent PM (hibernate and suspend) notifiers from being called
during the cleanup phase if they have not been called during the
corresponding preparation phase which is possible if one of the
other notifiers returns an error at that time (Lianwei Wang).
- Improve suspend-related debug printout in the tasks freezer and
clean up suspend-related console handling (Roger Lu, Borislav
Petkov).
- Update the AnalyzeSuspend script in the kernel sources to version
4.2 (Todd Brandt).
- Modify the generic power domains framework to make it handle system
suspend/resume better (Ulf Hansson).
- Make the runtime PM framework avoid resuming devices synchronously
when user space changes the runtime PM settings for them and
improve its error reporting (Rafael Wysocki, Linus Walleij).
- Fix error paths in devfreq drivers (exynos, exynos-ppmu,
exynos-bus) and in the core, make some devfreq code explicitly
non-modular and change some of it into tristate (Bartlomiej
Zolnierkiewicz, Peter Chen, Paul Gortmaker).
- Add DT support to the generic PM clocks management code and make it
export some more symbols (Jon Hunter, Paul Gortmaker).
- Make the PCI PM core code slightly more robust against possible
driver errors (Andy Shevchenko).
- Make it possible to change DESTDIR and PREFIX in turbostat (Andy
Shevchenko)"
* tag 'pm-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (89 commits)
Revert "cpufreq: pcc-cpufreq: update default value of cpuinfo_transition_latency"
PM / hibernate: Introduce test_resume mode for hibernation
cpufreq: export cpufreq_driver_resolve_freq()
cpufreq: Disallow ->resolve_freq() for drivers providing ->target_index()
PCI / PM: check all fields in pci_set_platform_pm()
cpufreq: acpi-cpufreq: use cached frequency mapping when possible
cpufreq: schedutil: map raw required frequency to driver frequency
cpufreq: add cpufreq_driver_resolve_freq()
cpufreq: intel_pstate: Check cpuid for MSR_HWP_INTERRUPT
intel_pstate: Update cpu_frequency tracepoint every time
cpufreq: intel_pstate: clean remnant struct element
PM / tools: scripts: AnalyzeSuspend v4.2
x86 / hibernate: Use hlt_play_dead() when resuming from hibernation
cpufreq: powernv: Replacing pstate_id with frequency table index
intel_pstate: Fix MSR_CONFIG_TDP_x addressing in core_get_max_pstate()
PM / hibernate: Image data protection during restoration
PM / hibernate: Add missing braces in __register_nosave_region()
PM / hibernate: Clean up comments in snapshot.c
PM / hibernate: Clean up function headers in snapshot.c
PM / hibernate: Add missing braces in hibernate_setup()
...
later merged with 'for-4.8/core' to pickup the QUEUE_FLAG_DAX commits
that DM depends on to provide its DAX support
- clean up the bio-based vs request-based DM core code by moving the
request-based DM core code out to dm-rq.[hc]
- reinstate bio-based support in the DM multipath target (done with the
idea that fast storage like NVMe over Fabrics could benefit) -- while
preserving support for request_fn and blk-mq request-based DM mpath
- SCSI and DM multipath persistent reservation fixes that were
coordinated with Martin Petersen.
- the DM raid target saw the most extensive change this cycle; it now
provides reshape and takeover support (by layering ontop of the
corresponding MD capabilities)
- DAX support for DM core and the linear, stripe and error targets
- A DM thin-provisioning block discard vs allocation race fix that
addresses potential for corruption
- A stable fix for DM verity-fec's block calculation during decode
- A few cleanups and fixes to DM core and various targets
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXkRZmAAoJEMUj8QotnQNat2wH/i4LpkoGI5tI6UhyKWxRkzJp
vKaJ0zuZ2Ez73DucJujNuvaiyHq1IjHD5pfr8JQO3E8ygDkRC2KjF2O8EXp0Has6
U1uLahQej72MAs0ZJTpvfE+JiY6qyIl4K+xxuPmYm2f2S5TWTIgOetYjJQmcMlQo
Y8zFfcDYn4Dv5rMdvDT4+1ePETxq74wcBwTxyW3OAbHE1f0JjsUGdMKzXB1iTWcM
VjLjWI//ETfFdIlDO0w2Qbd90aLUjmTR2k67RGnbPj5kNUNikv/X6iiY32KERR/0
vMiiJ7JS+a44P7FJqCMoAVM/oBYFiSNpS4LYevOgHb0G0ikF8kaSeqBPC6sMYvg=
=uYt9
-----END PGP SIGNATURE-----
Merge tag 'dm-4.8-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
- initially based on Jens' 'for-4.8/core' (given all the flag churn)
and later merged with 'for-4.8/core' to pickup the QUEUE_FLAG_DAX
commits that DM depends on to provide its DAX support
- clean up the bio-based vs request-based DM core code by moving the
request-based DM core code out to dm-rq.[hc]
- reinstate bio-based support in the DM multipath target (done with the
idea that fast storage like NVMe over Fabrics could benefit) -- while
preserving support for request_fn and blk-mq request-based DM mpath
- SCSI and DM multipath persistent reservation fixes that were
coordinated with Martin Petersen.
- the DM raid target saw the most extensive change this cycle; it now
provides reshape and takeover support (by layering ontop of the
corresponding MD capabilities)
- DAX support for DM core and the linear, stripe and error targets
- a DM thin-provisioning block discard vs allocation race fix that
addresses potential for corruption
- a stable fix for DM verity-fec's block calculation during decode
- a few cleanups and fixes to DM core and various targets
* tag 'dm-4.8-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (73 commits)
dm: allow bio-based table to be upgraded to bio-based with DAX support
dm snap: add fake origin_direct_access
dm stripe: add DAX support
dm error: add DAX support
dm linear: add DAX support
dm: add infrastructure for DAX support
dm thin: fix a race condition between discarding and provisioning a block
dm btree: fix a bug in dm_btree_find_next_single()
dm raid: fix random optimal_io_size for raid0
dm raid: address checkpatch.pl complaints
dm: call PR reserve/unreserve on each underlying device
sd: don't use the ALL_TG_PT bit for reservations
dm: fix second blk_delay_queue() parameter to be in msec units not jiffies
dm raid: change logical functions to actually return bool
dm raid: use rdev_for_each in status
dm raid: use rs->raid_disks to avoid memory leaks on free
dm raid: support delta_disks for raid1, fix table output
dm raid: enhance reshape check and factor out reshape setup
dm raid: allow resize during recovery
dm raid: fix rs_is_recovering() to allow for lvextend
...
Randy reported below build error.
> In file included from ../include/linux/balloon_compaction.h:48:0,
> from ../mm/balloon_compaction.c:11:
> ../include/linux/compaction.h:237:51: warning: 'struct node' declared inside parameter list [enabled by default]
> static inline int compaction_register_node(struct node *node)
> ../include/linux/compaction.h:237:51: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
> ../include/linux/compaction.h:242:54: warning: 'struct node' declared inside parameter list [enabled by default]
> static inline void compaction_unregister_node(struct node *node)
>
It was caused by non-lru page migration which needs compaction.h but
compaction.h doesn't include any header to be standalone.
I think proper header for non-lru page migration is migrate.h rather
than compaction.h because migrate.h has already headers needed to work
non-lru page migration indirectly like isolate_mode_t, migrate_mode
MIGRATEPAGE_SUCCESS.
[akpm@linux-foundation.org: revert mm-balloon-use-general-non-lru-movable-page-feature-fix.patch temp fix]
Link: http://lkml.kernel.org/r/20160610003304.GE29779@bbox
Signed-off-by: Minchan Kim <minchan@kernel.org>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Gioh Kim <gi-oh.kim@profitbricks.com>
Cc: Rafael Aquini <aquini@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The idea borrowed from Peter's patch from patchset on speculative page
faults[1]:
Instead of passing around the endless list of function arguments,
replace the lot with a single structure so we can change context without
endless function signature changes.
The changes are mostly mechanical with exception of faultaround code:
filemap_map_pages() got reworked a bit.
This patch is preparation for the next one.
[1] http://lkml.kernel.org/r/20141020222841.302891540@infradead.org
Link: http://lkml.kernel.org/r/1466021202-61880-9-git-send-email-kirill.shutemov@linux.intel.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have allowed migration for only LRU pages until now and it was enough
to make high-order pages. But recently, embedded system(e.g., webOS,
android) uses lots of non-movable pages(e.g., zram, GPU memory) so we
have seen several reports about troubles of small high-order allocation.
For fixing the problem, there were several efforts (e,g,. enhance
compaction algorithm, SLUB fallback to 0-order page, reserved memory,
vmalloc and so on) but if there are lots of non-movable pages in system,
their solutions are void in the long run.
So, this patch is to support facility to change non-movable pages with
movable. For the feature, this patch introduces functions related to
migration to address_space_operations as well as some page flags.
If a driver want to make own pages movable, it should define three
functions which are function pointers of struct
address_space_operations.
1. bool (*isolate_page) (struct page *page, isolate_mode_t mode);
What VM expects on isolate_page function of driver is to return *true*
if driver isolates page successfully. On returing true, VM marks the
page as PG_isolated so concurrent isolation in several CPUs skip the
page for isolation. If a driver cannot isolate the page, it should
return *false*.
Once page is successfully isolated, VM uses page.lru fields so driver
shouldn't expect to preserve values in that fields.
2. int (*migratepage) (struct address_space *mapping,
struct page *newpage, struct page *oldpage, enum migrate_mode);
After isolation, VM calls migratepage of driver with isolated page. The
function of migratepage is to move content of the old page to new page
and set up fields of struct page newpage. Keep in mind that you should
indicate to the VM the oldpage is no longer movable via
__ClearPageMovable() under page_lock if you migrated the oldpage
successfully and returns 0. If driver cannot migrate the page at the
moment, driver can return -EAGAIN. On -EAGAIN, VM will retry page
migration in a short time because VM interprets -EAGAIN as "temporal
migration failure". On returning any error except -EAGAIN, VM will give
up the page migration without retrying in this time.
Driver shouldn't touch page.lru field VM using in the functions.
3. void (*putback_page)(struct page *);
If migration fails on isolated page, VM should return the isolated page
to the driver so VM calls driver's putback_page with migration failed
page. In this function, driver should put the isolated page back to the
own data structure.
4. non-lru movable page flags
There are two page flags for supporting non-lru movable page.
* PG_movable
Driver should use the below function to make page movable under
page_lock.
void __SetPageMovable(struct page *page, struct address_space *mapping)
It needs argument of address_space for registering migration family
functions which will be called by VM. Exactly speaking, PG_movable is
not a real flag of struct page. Rather than, VM reuses page->mapping's
lower bits to represent it.
#define PAGE_MAPPING_MOVABLE 0x2
page->mapping = page->mapping | PAGE_MAPPING_MOVABLE;
so driver shouldn't access page->mapping directly. Instead, driver
should use page_mapping which mask off the low two bits of page->mapping
so it can get right struct address_space.
For testing of non-lru movable page, VM supports __PageMovable function.
However, it doesn't guarantee to identify non-lru movable page because
page->mapping field is unified with other variables in struct page. As
well, if driver releases the page after isolation by VM, page->mapping
doesn't have stable value although it has PAGE_MAPPING_MOVABLE (Look at
__ClearPageMovable). But __PageMovable is cheap to catch whether page
is LRU or non-lru movable once the page has been isolated. Because LRU
pages never can have PAGE_MAPPING_MOVABLE in page->mapping. It is also
good for just peeking to test non-lru movable pages before more
expensive checking with lock_page in pfn scanning to select victim.
For guaranteeing non-lru movable page, VM provides PageMovable function.
Unlike __PageMovable, PageMovable functions validates page->mapping and
mapping->a_ops->isolate_page under lock_page. The lock_page prevents
sudden destroying of page->mapping.
Driver using __SetPageMovable should clear the flag via
__ClearMovablePage under page_lock before the releasing the page.
* PG_isolated
To prevent concurrent isolation among several CPUs, VM marks isolated
page as PG_isolated under lock_page. So if a CPU encounters PG_isolated
non-lru movable page, it can skip it. Driver doesn't need to manipulate
the flag because VM will set/clear it automatically. Keep in mind that
if driver sees PG_isolated page, it means the page have been isolated by
VM so it shouldn't touch page.lru field. PG_isolated is alias with
PG_reclaim flag so driver shouldn't use the flag for own purpose.
[opensource.ganesh@gmail.com: mm/compaction: remove local variable is_lru]
Link: http://lkml.kernel.org/r/20160618014841.GA7422@leo-test
Link: http://lkml.kernel.org/r/1464736881-24886-3-git-send-email-minchan@kernel.org
Signed-off-by: Gioh Kim <gi-oh.kim@profitbricks.com>
Signed-off-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Ganesh Mahendran <opensource.ganesh@gmail.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rafael Aquini <aquini@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: John Einar Reitan <john.reitan@foss.arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
zram documentation is a mix of different styles: spaces, tabs, tabs +
spaces, etc. Clean it up.
Link: http://lkml.kernel.org/r/20160531122017.2878-6-sergey.senozhatsky@gmail.com
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no way to get a string with all the crypto comp algorithms
supported by the crypto comp engine, so we need to maintain our own
backends list. At the same time we additionally need to use
crypto_has_comp() to make sure that the user has requested a compression
algorithm that is recognized by the crypto comp engine. Relying on
/proc/crypto is not an options here, because it does not show
not-yet-inserted compression modules.
Example:
modprobe zram
cat /proc/crypto | grep -i lz4
modprobe lz4
cat /proc/crypto | grep -i lz4
name : lz4
driver : lz4-generic
module : lz4
So the user can't tell exactly if the lz4 is really supported from
/proc/crypto output, unless someone or something has loaded it.
This patch also adds crypto_has_comp() to zcomp_available_show(). We
store all the compression algorithms names in zcomp's `backends' array,
regardless the CONFIG_CRYPTO_FOO configuration, but show only those that
are also supported by crypto engine. This helps user to know the exact
list of compression algorithms that can be used.
Example:
module lz4 is not loaded yet, but is supported by the crypto
engine. /proc/crypto has no information on this module, while
zram's `comp_algorithm' lists it:
cat /proc/crypto | grep -i lz4
cat /sys/block/zram0/comp_algorithm
[lzo] lz4 deflate lz4hc 842
We still use the `backends' array to determine if the requested
compression backend is known to crypto api. This array, however, may not
contain some entries, therefore as the last step we call crypto_has_comp()
function which attempts to insmod the requested compression algorithm to
determine if crypto api supports it. The advantage of this method is that
now we permit the usage of out-of-tree crypto compression modules
(implementing S/W or H/W compression).
[sergey.senozhatsky@gmail.com: zram-use-crypto-api-to-check-alg-availability-v3]
Link: http://lkml.kernel.org/r/20160604024902.11778-4-sergey.senozhatsky@gmail.com
Link: http://lkml.kernel.org/r/20160531122017.2878-5-sergey.senozhatsky@gmail.com
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>