More stuff for http://bugzilla.kernel.org/show_bug.cgi?id=9512
Some 8168 are unable to WoL when receiving is not enabled (plain
old 8169 do not seem to care).
It is not exactly pretty to leave the receiver enabled but we
should now enable DMA late enough for it to be safe. Some late
stage boot failure due to pxe and friends may benefit from the
delayed enabling of bus-mastering as well.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Jaromír Cápík <tavvva@volny.cz>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
all references got removed by 865c652d6b
(r8169: remove non-napi code).
Signed-off-by: Florian Westphal <fwestphal@astaro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stopping all activity through ChipCmd and blindly acking the irqs
is neither nice nor completely needed: the transition to low-power
mode does enough work and it apparently keeps the device in a sane
state.
Patch suggested by a fix for http://bugzilla.kernel.org/show_bug.cgi?id=9512
The rtl_shutdown path is kept unchanged so far.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Anders Eriksson <aeriksson@fastmail.fm>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8169_tx_interrupt() is used from NAPI context, it can
directly free skbs. dev_kfree_skb_irq() is a leftover from
pre-NAPI times of this driver.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Tokarev reported receiving a large packet could crash
a machine with RTL8169 NIC.
( original thread at http://lkml.org/lkml/2009/6/8/192 )
Problem is this driver tells that NIC frames up to 16383 bytes
can be received but provides skb to rx ring allocated with
smaller sizes (1536 bytes in case standard 1500 bytes MTU is used)
When a frame larger than what was allocated by driver is received,
dma transfert can occurs past the end of buffer and corrupt
kernel memory.
Fix is to tell to NIC what is the maximum size a frame can be.
This bug is very old, (before git introduction, linux-2.6.10), and
should be backported to stable versions.
Reported-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Second round of drivers for Gb cards (and NIU one I forgot in the 10GB round)
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.
Exceptions are NETIF_F_LLTX drivers
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The r8169 driver supports 3 different families of network chips
(RTL8169, RTL8168 and RTL8101). When an unknown version is found, the
driver currently always defaults to the RTL8169 variant. This has very
little chance to ever work for chips of the other families. So better
define a per-family default.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 8169 chip only generates MSI interrupts when all enabled event
sources are quiescent and one or more sources transition to active. If
not all of the active events are acknowledged, or a new event becomes
active while the existing ones are cleared in the handler, we will not
see a new interrupt.
The current interrupt handler masks off the Rx and Tx events once the
NAPI handler has been scheduled, which opens a race window in which we
can get another Rx or Tx event and never ACK'ing it, stopping all
activity until the link is reset (ifconfig down/up). Fix this by always
ACK'ing all event sources, and loop in the handler until we have all
sources quiescent.
Signed-off-by: David Dillow <dave@thedillows.org>
Tested-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to mostly historic reasons, including a lack of reliability
of the link handling (especially with the older 8169), the
current r8169 driver emulates forced mode setting by limiting
the advertised modes.
With this change the driver allows real 10/100 forced mode
settings on the 8169 and 8101/8102.
Original idea by Vincent Steenhoute. The RTL_GIGA_MAC_VER_03
tweak was extracted from Realtek's r8169 v6.010.00 driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Jean Delvare <jdelvare@suse.de>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent changes of the PCI PM core allow us to simplify the
suspend and resume handling in a number of device drivers, since they
don't need to carry out the general PCI PM operations, such as
changing the power state of the device, during suspend and resume any
more.
Simplify the suspend and resume callbacks of r8169 using the
observation that the PCI PM core can take care of some operations
carried out by the driver.
Additionally, make the shutdown callback of r8169 only put the device
into a low power state if the system is going to be powered off
(kexec is known to have problems with network adapters that are put
into low power states on shutdown).
This patch has been tested on MSI Wind U100.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Original comment (Karsten):
On a MSI MS-6702E mainboard, when in rtl8169_init_one() for the first time
after BIOS has run, IntrStatus reads 5 after chip has been reset.
IntrStatus should equal 0 there, so patch changes IntrStatus reset to happen
after chip reset instead of before.
Remark (Francois):
Assuming that the loglevel of the driver is increased above NETIF_MSG_INTR,
the bug reveals itself with a typical "interrupt 0025 in poll" message
at startup. In retrospect, the message should had been read as an hint of
an unexpected hardware state several months ago :o(
Fixes (at least part of) https://bugzilla.redhat.com/show_bug.cgi?id=460747
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Josep <josep.puigdemont@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It fails on the following systems:
- RTL8169sc/8110sc (XID 18000000)
reported by Tim Durack <tdurack@gmail.com> (x86)
- RTL8169sb/8110sb (XID 10000000)
reported by Mikael Pettersson <mikpe@it.uu.se> (ARM)
The patch appeared to work on x86 for the following systems:
RTL8169sb/8110sb 10000000 PCI (EXT)
RTL8110s 04000000 PCI (EXT)
RTL8102e 24a00000 PCI-E (LOM)
RTL8168c/8111c 3c2000c0 PCI-E (LOM)
RTL8168b/8111b 38000000 PCI-E (LOM)
RTL8168b/8111b 38000000 PCI-E (EXT)
The patch exposes two problems:
1) while not completely wrong, mac addresses are not read correctly
from the EEPROM
2) the MAC address registers are not correctly set
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
It shortens the code and fixes the current pci_unmap leak with
padded skb reported by Dave Jones.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is 2nd attempt to implement the initialization/reading of MAC address
from EEPROM. The first used PCI's VPD and there were some problems, some
devices are not able to read EEPROM content by VPD. The 2nd one uses direct
access to EEPROM through bit-banging interface and my testing results seem
to be much better.
I tested 5 systems each with different Realtek NICs and I didn't find any
problem. AFAIK Francois's NICs also works fine.
Original description:
This fixes the problem when MAC address is set by ifconfig or by
ip link commands and this address is stored in the device after
reboot. The power-off is needed to get right MAC address.
This is problem when Xen daemon is running because it renames the device
name from ethX to pethX and sets its MAC address to FE:FF:FF:FF:FF:FF.
After reboot the device is still using FE:FF:FF:FF:FF:FF.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Realtek chips (RTL8169sb/8110sb in my case) are unable to retrieve
ethtool statistics when the interface is down. The process stays in
endless loop in rtl8169_get_ethtool_stats. This is because these chips
need to have receiver enabled (CmdRxEnb bit in ChipCmd register) that is
cleared when the interface is going down. It's better to update statistics
only when the interface is up and otherwise return copy of statistics
grabbed when the interface was up (in rtl8169_close).
It is interesting that PCI-E NICs (like 8168b/8111b...) are not affected.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the removal of the unused struct net_device * parameter from
the NAPI functions named *netif_rx_* in commit 908a7a1, they are
exactly equivalent to the corresponding *napi_* functions and are
therefore redundant.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the napi api was changed to separate its 1:1 binding to the net_device
struct, the netif_rx_[prep|schedule|complete] api failed to remove the now
vestigual net_device structure parameter. This patch cleans up that api by
properly removing it..
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves neigh_setup and hard_start_xmit into the network device ops
structure. For bisection, fix all the previously converted drivers as well.
Bonding driver took the biggest hit on this.
Added a prefetch of the hard_start_xmit in the fast path to try and reduce
any impact this would have.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Drivers need not do it any more.
Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 7bf6bf4803.
The code has both a short existence and an increasing track of failures
despite some work to amend it for -rc1. It is not just a matter of
reading the eeprom: sometimes the eeprom is read correctly, then the mac
address is not written correctly back into the mac registers.
Some chipsets seem to work reliably but it is not clear at this point if
the code can simply be made to work on a per-chipset basis and post -rc1
is not the place where I want to experiment these things.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Checking the signature of the eeprom and the validity of the
MAC address should be enough to filter out the bad addresses
observed so far.
Contributed by Ivan Vecera and Martin Capitanio.
Tested on 8102el, 8168b and 8169 for a start.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
I prefer the debug information to be displayed until
the issue is properly handled.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
mmio_addr in r8169 needs to be initialized before use
Maybe that all tp-> initialization should be moved before rtl_init_mac_address call,
but this is enough to get rid of crash in rtl_rar_set due to mmio_addr being uninitialized.
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taken from Realtek's 8.007.00 r8168 driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Fixed-by: Ivan Vecera <ivecera@redhat.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Taken from Realtek's 8.007.00 r8168 driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Fixed-by: Ivan Vecera <ivecera@redhat.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
The addition of a new device has so far implied a specialization of
these masks. While they identify 8168c devices, they can be expected
to be further refined as they have been by Realtek so far.
The change should bring the driver closer to the version 8.006.00 of
Realtek's 8168 driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Taken from Realtek's 8.006.00 r8168 driver.
I have left some bits related to jumbo frame aside for now.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Taken from Realtek's 8.006.00 r8168 driver.
I have left some bits related to jumbo frame aside for now.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
This part of the driver should be reasonably in line with Realtek's
8.006.00 driver.
I have left some bits related to jumbo frame and optional features
aside for now.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Broadly speaking the 8168c* share some common code which will
be factored in __rtl_hw_start_8168cp. The 8168b* share some
code too but it will be a bit different.
Any change of behavior should be confined to the currently
unidentified 8168 chipsets. They will not be applied the Tx
performance tweak and will emit a warning instead.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
I can not argue strongly for (or against) a specific ordering
on a purely technical ground but the patch avoids to swallow
Realtek's changes in one big, hard-to-read gulp.
Let aside the way the RxConfig register is written (see
rtl_set_rx_tx_config_registers / RxConfig / rtl_set_rx_mode),
this change brings the registers write ordering closer with
Realtek's driver one (version 8.006.00) for the 8168 chipsets.
More 8168 specific code which touches the Configx registers will
be added in the section covered by Cfg9346_UnLock / Cfg9346_Lock.
This code should not be the cause of regression for 810x and
8110 users.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
The new parameters are synced with Realtek's driver
version 8.006.00.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
The modified parameters are synced with Realtek's driver
version 8.006.00.
The change should only be noticeable with some 8168c.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
This is typically needed when some other OS puts the PHY
to sleep due to the disabling of WOL options in the BIOS
of the system.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Chiaki Ishikawa <chiaki.ishikawa@ubin.jp>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Cc: RyanKao <ryankao@realtek.com.tw>
Since recent kernel (2.6.26 or 2.6.27) the PCI wakeup functions are
influenced by generic device ability and configuration when enabling
PCI-device triggered wake-up.
This patch causes WoL setting to enable/disable device's wish to
be permitted to wake-up the host when changing WoL options and
also during device probing.
Without this patch one has write 'enabled' to
/sys/bus/pci/devices/0000:02:08.0/power/wakeup
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
When probing the chip and handling it's power management settings
also remember wether WoL feature is enabled.
Without this patch one has to call ethtool to change WoL settings
for this flag to be set and any WoL being enabled on suspend to
RAM.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
- the register is defined for the 8169 chipset only and there is
no 8169 beyond RTL_GIGA_MAC_VER_06.
- only the lower 3 bytes of the register are valid
Fixes:
1. http://bugzilla.kernel.org/show_bug.cgi?id=10180
2. http://bugzilla.kernel.org/show_bug.cgi?id=11062 (bits of)
Tested by Hermann Gausterer and Adam Huffman.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The leak hurts with swiotlb and jumbo frames.
Fix http://bugzilla.kernel.org/show_bug.cgi?id=9468.
Heavily hinted by Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Alistair John Strachan <alistair@devzero.co.uk>
Tested-by: Timothy J Fontaine <tjfontaine@atxconsulting.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This commit triggers three 'defined but not used' warnings but
I prefer avoiding to tie these helpers to a specific change in
the hw start sequences of the 8168 or of the 8101.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
It avoids to report unsupported link capabilities with
the fast-ethernet only 8101/8102.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Martin Capitanio <martin@capitanio.org>
Fixed-by: Ivan Vecera <ivecera@redhat.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
The magic write to register 0x82 will often cause PCI config space on
my 8168 (PCI ID 10ec:8168, revision 2. mounted in an LG P300 laptop)
to be filled with ones during driver load, and thus breaking NIC
operation until reboot. If it does not happen on first driver load it
can easily be reproduced by unloading and loading the driver a few
times.
The magic write was added long ago by this commit:
Author: François Romieu <romieu@fr.zoreil.com>
Date: Sat Jan 10 06:00:46 2004 -0500
[netdrvr r8169] Merge of changes done by Realtek to rtl8169_init_one():
- phy capability settings allows lower or equal capability as suggested
in Realtek's changes;
- I/O voodoo;
- no need to s/mdio_write/RTL8169_WRITE_GMII_REG/;
- s/rtl8169_hw_PHY_config/rtl8169_hw_phy_config/;
- rtl8169_hw_phy_config(): ad-hoc struct "phy_magic" to limit duplication
of code (yep, the u16 -> int conversions should work as expected);
- variable renames and whitepace changes ignored.
As the 8168 wasn't supported by that version this patch simply removes
the bogus write from mac versions <= RTL_GIGA_MAC_VER_06.
[The change above makes sense for the 8101/8102 too -- Ueimor]
Signed-off-by: Marcus Sundberg <marcus@ingate.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
The layout of the 8101 series is identical to that of the 8168 one,
thus allowing to pack everything not 8169 related above MAC_VER_06.
New 810x and 8168 chipsets should automagically behave correctly.
It matches code in Realtek's 1.008.00 8101 and 8.007.00 8168 drivers.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
It will almost unavoidably cause some breakage but it
is long overdue.
The driver identification string has been updated, a
lost tabulation and some unused code have been removed.
Otherwise the code paths should stay the same.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
The layout of the 8168 serie is different from that of the 8110 one.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
r8169_get_mac_version crashes when it meets an unknown MAC
due to tp->pci_dev not being set. Initialize it early.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
When we add the generic napi_disable_pending() breakout
logic to net_rx_action() it means that napi_disable()
can cause NAPI poll interrupt events to be disabled.
And this is exactly what we want. If a napi_disable()
is pending, and we are looping in the ->poll(), we want
->poll() event interrupts to stay disabled and we want
to complete the NAPI poll ASAP.
When ->poll() break out during device down was being handled on a
per-driver basis, often these drivers would turn interrupts back on
when '!netif_running()' was detected.
And this would just cause a reschedule of the NAPI ->poll() in the
interrupt handler before the napi_disable() could get in there and
grab the NAPI_STATE_SCHED bit.
The vast majority of drivers don't care if napi_disable() might have
the side effect of disabling NAPI ->poll() event interrupts. In all
such cases, when a napi_disable() is performed, the driver just
disabled interrupts or is about to.
However there were three exceptions to this in PCNET32, R8169, and
SKY2. To fix those cases, at the subsequent napi_enable() points, I
added code to ensure that the ->poll() interrupt events are enabled in
the hardware.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Don Fry <pcnet32@verizon.net>
Oops.
The current code does not like being given an u16 with the highest
bit set as an argument to mdio_write. Let's enforce a correct range of
values for both the register address and value (resp. 5 and 16 bits).
The callers are currently left as-is.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
RTL_GIGA_MAC_VER_17 breaks as well.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Various symptoms depending on the .config options:
- the card stops working after some (short) time
- the card does not work at all
- the card disappears (nothing in lspci/dmesg)
A real power-off is needed to recover the card.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
The 8168c and the 8100e choke on it. I have not seen an indication
nor received a report that the TBI is being actively used on the
remaining 8168b and 8110. Let's disable it for now until someone
complains.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Matthias Winkler <m.winkler@unicon-ka.de>
Cc: Maarten Vanraes <maarten.vanraes@gmail.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Disabling napi polling early is well enough.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Don't call napi_disable if not configured and make sure that any
misuse of napi_xxx in future fails with a compile error.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Realtek's r8168 driver version 8.003.00 adds new init sequences
(they do not appear in version 8.002.00).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
The values have been updated between version 8.002.00 and version
8.003.00 of Realtek's r8168 driver. This modification syncs the
8168C with version 8.003.00.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Consistent use of hexadecimal. No change of behavior otherwise.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
The values have been extracted from Realtek's r8168 driver
version 8.002.00.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
The code is reworked to easily add phy-dependant init changes.
No change of behavior should be noticed.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
The identifiers have been extracted from Realtek's drivers:
- version 8.002.00 of the r8168 driver
- version 6.002.00 of the r8169 driver
- version 1.002.00 of the r8101 driver
1. RTL_GIGA_MAC_VER_17 (8168Bf) is isolated from RTL_GIGA_MAC_VER_12 (8168Be)
Both are still handled the same in rtl8169_set_speed_xmii and in
rtl_set_rx_mode to avoid changes of behavior in this patch.
2. RTL_GIGA_MAC_VER_16 (8101Ec) is isolated from RTL_GIGA_MAC_VER_13 (8101Eb)
Same thing as above with relation to rtl8169_set_speed_xmii,
rtl_set_rx_mode and rtl_hw_start_8101.
3. The remaining new identifiers should not hurt.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
It is currently limited to the tested 0x8136 and 0x8168. 8169sb/8110sb ought
to handle it as well where they support MSI.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Tester-Cc: Rolf Eike Beer <eike-kernel@sf-tec.de>
- prefix dprintk with KERN_DEBUG
- fix a bug with existing use of dprintk (PFX KERN_INFO PFX)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
These have been superceded by the new ->get_sset_count() hook.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the operations
get-tx-csum
get-sg
get-tso
get-ufo
the default ethtool_op_xxx behavior is fine for all drivers, so we
permit op==NULL to imply the default behavior.
This provides a more uniform behavior across all drivers, eliminating
ethtool(8) "ioctl not supported" errors on older drivers that had
not been updated for the latest sub-ioctls.
The ethtool_op_xxx() functions are left exported, in case anyone
wishes to call them directly from a driver-private implementation --
a not-uncommon case. Should an ethtool_op_xxx() helper remain unused
for a while, except by net/core/ethtool.c, we can un-export it at a
later date.
[ Resolved conflicts with set/get value ethtool patch... -DaveM ]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several devices have multiple independant RX queues per net
device, and some have a single interrupt doorbell for several
queues.
In either case, it's easier to support layouts like that if the
structure representing the poll is independant from the net
device itself.
The signature of the ->poll() call back goes from:
int foo_poll(struct net_device *dev, int *budget)
to
int foo_poll(struct napi_struct *napi, int budget)
The caller is returned the number of RX packets processed (or
the number of "NAPI credits" consumed if you want to get
abstract). The callee no longer messes around bumping
dev->quota, *budget, etc. because that is all handled in the
caller upon return.
The napi_struct is to be embedded in the device driver private data
structures.
Furthermore, it is the driver's responsibility to disable all NAPI
instances in it's ->stop() device close handler. Since the
napi_struct is privatized into the driver's private data structures,
only the driver knows how to get at all of the napi_struct instances
it may have per-device.
With lots of help and suggestions from Rusty Russell, Roland Dreier,
Michael Chan, Jeff Garzik, and Jamal Hadi Salim.
Bug fixes from Thomas Graf, Roland Dreier, Peter Zijlstra,
Joseph Fannin, Scott Wood, Hans J. Koch, and Michael Chan.
[ Ported to current tree and all drivers converted. Integrated
Stephen's follow-on kerneldoc additions, and restored poll_list
handling to the old style to fix mutual exclusion issues. -DaveM ]
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 8169/8110SC currently announces itself as:
[...]
eth0: RTL8169sc/8110sc at 0x........, ..:..:..:..:..:.., XID 18000000 IRQ ..
^^^^^^^^
It uses RTL_GIGA_MAC_VER_05 and this part of the changeset can cut
its performance by a factor of 2~2.5 as reported by Timo.
(the driver includes code just before the hunk to write the ChipCmd
register when mac_version == RTL_GIGA_MAC_VER_0[1-4])
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Timo Jantunen <jeti@welho.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The 8168 ignores the requests to fetch the Tx descriptors when
the relevant TxPoll bit is already set. It easily kills the
performances of the 8168. David Gundersen has noticed that it
is enough to wait for the completion of the DMA transfer (NPQ
bit is cleared) before writing the TxPoll register again.
The extra IO traffic added by the proposed workaround could be
minimalized but it is not a high-priority task.
Fix for:
http://bugzilla.kernel.org/show_bug.cgi?id=7924http://bugzilla.kernel.org/show_bug.cgi?id=8688
(http://bugzilla.kernel.org/show_bug.cgi?id=7555 ?)
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: David Gundersen <gundy@iinet.net.au>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
The phys of the 8110SC (RTL_GIGA_MAC_VER_{05/06}) act abnormally in
gigabit mode if they are applied the parameters in rtl8169_hw_phy_config
which actually aim the 8110S/SB.
It is ok to return early from rtl8169_hw_phy_config as it does not
apply to the 8101 and 8168 families.
Signed-off-by: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Theory : though needless, it should not have hurt.
Practice: it does not play nice with DEBUG_SHIRQ + LOCKDEP + UP
(see https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=242572).
The patch makes sense in itself but I should dig why it has an effect
on #242572 (assuming that NAPI do not change in a near future).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Fix extracted from Realtek's driver (8.002.00/20070713) for the PHY
attached to 8111/8168b chipsets.
The check against mac_version is just usual paranoia during the bugfix
period of the kernel cycle. -- FR
Tested on Asus M2A-VM motherboard by Roger So.
No regression on my Asrock 945G DVI either (built-in 8168 + 2x8169).
Signed-off-by: Roger So <roger.so@gmail.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
All drivers implement ethtool get_perm_addr the same way -- by calling
the generic function. So we can inline the generic function into the
caller and avoid going through the drivers.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mark variables in drivers/* with uninitialized_var() if such a warning
appears, and analysis proves that the var is initialized properly on all
paths it is used.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It does not really make sense to update the RX config register
before the mac filtering registers.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Merged from Realtek's r8169-6.001 driver.
I have added some locking to protect against the arp monitoring
timer in the bonding driver. Accessing the configuration registers
is otherwise performed under RTNL locking.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
It does not cost much and it will ease the identification of (so far)
unknown devices.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Align the IP header when the chipset can DMA at any location (plain 0x8169).
Otherwise (0x8136/0x8168) obey the constraint imposed by the hardware.
This patch complements the previous alignment rework done for copybreak.
Original idea from Philip Craig <philipc@snapgear.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Philip Craig <philipc@snapgear.com>
Cc: Mike Isely <isely@pobox.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
No functionnal change:
- trim the old history log
- whitespace/indent/case police
- unsigned int where signedness does not matter
- removal of obsolete assert
- needless cast from void * (dev_instance)
- remove dead code once related to power management
- use netdev_alloc_skb.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
It has been documented as deprecated:
- in MODULE_PARM_DESC since may 2005 ;
- at the top of the source file and in printk since june 2004.
Good bye.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
The rx copybreak part is straightforward.
The align field in struct rtl_cfg_info is related to the alignment
requirements of the DMA operation. Its value is set at 2 to limit the
scale of possible regression but my old v1.21 8169 datasheet claims a
8 bytes requirements (which never appeared in the driver, of course)
and the 8101/8168 go with a plain 8 bytes alignment.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
This one includes:
- more tweaks to rtl_hw_start_8168
- a work around for a Rx FiFO overflow issue on the 8168Bb
- rtl8169_{intr_mask/napi_event} are replaced with per-device fields,
namely tp->{intr/napi}_event
- rtl_cfg_info is converted to C99 for readability but the values are
not changed for the 8169/8110 and the 8101
Includes ChipCmd fix from Bernhard Walle <bwalle@suse.de> (2007/02/24).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
- new identifier for the 8110SCe
- the PCI latency timer is set unconditionally. This part is identical
in Realtek's r8168 (8.001.00) and r8101 (1.001.00)
- initialization of the cache line size register is for the 8169s only
- more magic in rtl_hw_start_8169
- it is not possible to factor out the setting of the the irq event mask
with the 8168 and the 8101 any more. Pushed it into the hw_start handler.
- rtl_set_rx_tx_config_registers() and write to the ChipCmd register are
issued identically for the whole 8169/8110 family: the 8110SCd/8110SCe
are handled the same way
- work around for AMD platform.
Some registers definitions in Realtek's driver are let aside for later.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Same thing as the previous change for rtl_hw_start_8168.
The 8101 related code in rtl_hw_start_8169 (see RTL_GIGA_MAC_VER_13)
goes away.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
rtl_hw_start_8168 inherits the content of rtl_hw_start_8169 minus
the code which depends on RTL_GIGA_MAC_VER_XY (XY != {11/12}).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
They aim to limit the amount of moved code when the hw_start
handler gets more specialized.
No functional change.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Rationale: rtl8169_hw_start will not help maintaining an unified
driver for different chipsets but people at Realtek are probably
too polite to say it distinctly.
Let's add the hook and keep hw_start handler unchanged.
As can be seen from the content of rtl8169_pci_tbl, the RTL_CFG_1
entry in rtl_cfg_info was unused. I recycled it for the 0x8168.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
- pci_dma_sync_single_for_cpu is not needed for a single large packet
- remove the function pointer to help gcc optimizing the inline
pci_dma functions.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
It hasn't "summed" anything in over 7 years, and it's
just a straight mempcy ala skb_copy_to_linear_data()
so just get rid of it.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
The former style suggests a modulo arithmetic misuse but
the expression should never be < 0. Even if it does, the
driver will simply loop longer than expected (not that
the remaining parts of the system will necessarily
appreciate it...).
Let's warn the user when something goes wrong and try
to go over it.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Use netdev_alloc_skb and remove the useless sk_buff * argument of
rtl8169_alloc_rx_skb.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Many drivers had code that did kill_vid, but they weren't doing vlan
filtering. With new API the stub is unneeded unless device sets
NETIF_F_HW_VLAN_FILTER.
Bad habit: I couldn't resist fixing a couple of nearby style things
in acenic, and forcedeth.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
One less thing for drivers writers to worry about.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PM hooks are no-op if the r8169 interface is down (i.e. !IFF_UP).
However, as the chipset is enabled, the device will not work after a
suspend/resume cycle. The patch always issue the required PCI suspend
sequence and removes the module unload/reload workaround.
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The irq handler schedules a NAPI poll request unconditionally as soon as
the status register is not clean. It has been there - and wrong - for
ages but a recent timing change made it apparently easier to trigger.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Initialize the timer with the rest of the private-struct.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Added during bf793295e1
The current code requests a reset but prohibits autoneg, 1000 Mb/s,
100 Mb/s and full duplex. The 8168 does not like it at all.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch splits the vlan_group struct into a multi-allocated struct. On
x86_64, the size of the original struct is a little more than 32KB, causing
a 4-order allocation, which is prune to problems caused by buddy-system
external fragmentation conditions.
I couldn't just use vmalloc() because vfree() cannot be called in the
softirq context of the RCU callback.
Signed-off-by: Dan Aloni <da-x@monatomic.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
flush_scheduled_work() in net_device->close has a slight tendency
to deadlock with tasks on the workqueue that hold RTNL.
rtl8169_close/down simply need the recovery tasks to not meddle
with the hardware while the device is going down.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Checked in Realtek's driver, this one has no business being there.
The driver still works but there is a noticeable performance drop.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
The former option is removed and platform code can now specify the
expected behavior.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Conflicts:
drivers/infiniband/core/iwcm.c
drivers/net/chelsio/cxgb2.c
drivers/net/wireless/bcm43xx/bcm43xx_main.c
drivers/net/wireless/prism54/islpci_eth.c
drivers/usb/core/hub.h
drivers/usb/input/hid-core.c
net/core/netpoll.c
Fix up merge failures with Linus's head and fix new compilation failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
Two thirds of packets are lost because of misalignment. Users of
Asus laptop did apparently not notice it.
Reported on Gigabyte GA-945GM-S2.
Fix for http://bugzilla.kernel.org/show_bug.cgi?id=7517
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
The 8110SB based n2100 board signals a lot of what ought to be
PCI data parity errors durint operation of the 8169 as target.
Experiment proved that the driver can ignore the error and
process the packet as if nothing had happened.
Let's add an ad-hoc knob to enable users to fix their system while
avoiding the risks of a wholesale change.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Mostly taken from Realtek's driver.
It's a bit yucky but the original is even worse.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Realtek's 8139/810x (0x8136) PCI-E comes with a touchy PHY.
A big heavy reset seems to calm it down.
Fix for http://bugzilla.kernel.org/show_bug.cgi?id=7378.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
This changes the type of variable "i" in rtl8169_init_one()
from "unsigned int" to "int". "i" is checked for < 0 later,
which can never happen for "unsigned". This results in broken
error handling.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This reverts commit a2b98a697f.
As per Guennadi Liakhovetski, the mac address change support code breaks
some normal uses (_without_ any address changes), and until it's all
sorted out, we're better off without it.
Says Francois:
"Go revert it.
Despite what I claimed, I can not find a third-party confirmation by
email that it works elsewhere.
It would probably be enough to remove the call to
__rtl8169_set_mac_addr() in rtl8169_hw_start() though."
See also
http://bugzilla.kernel.org/show_bug.cgi?id=6032
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (217 commits)
net/ieee80211: fix more crypto-related build breakage
[PATCH] Spidernet: add ethtool -S (show statistics)
[NET] GT96100: Delete bitrotting ethernet driver
[PATCH] mv643xx_eth: restrict to 32-bit PPC_MULTIPLATFORM
[PATCH] Cirrus Logic ep93xx ethernet driver
r8169: the MMIO region of the 8167 stands behin BAR#1
e1000, ixgb: Remove pointless wrappers
[PATCH] Remove powerpc specific parts of 3c509 driver
[PATCH] s2io: Switch to pci_get_device
[PATCH] gt96100: move to pci_get_device API
[PATCH] ehea: bugfix for register access functions
[PATCH] e1000 disable device on PCI error
drivers/net/phy/fixed: #if 0 some incomplete code
drivers/net: const-ify ethtool_ops declarations
[PATCH] ethtool: allow const ethtool_ops
[PATCH] sky2: big endian
[PATCH] sky2: fiber support
[PATCH] sky2: tx pause bug fix
drivers/net: Trim trailing whitespace
[PATCH] ehea: IBM eHEA Ethernet Device Driver
...
Manually resolved conflicts in drivers/net/ixgb/ixgb_main.c and
drivers/net/sky2.c related to CHECKSUM_HW/CHECKSUM_PARTIAL changes by
commit 84fa7933a3 that just happened to be
next to unrelated changes in this update.
françois romieu