This reverts commit 842067940a.
For some solutions e.g. sound/soc/intel/catpt, DW DMA is part of a
compound device (in that very example, domains: ADSP, SSP0, SSP1, DMA0
and DMA1 are part of a single entity) rather than being a standalone
one. Driver for said device may enlist DMA to transfer data during
suspend or resume sequences.
Manipulating RPM explicitly in dw's DMA request and release channel
functions causes suspend() to also invoke resume() for the exact same
device. Similar situation occurs for resume() sequence. Effectively
renders device dysfunctional after first suspend() attempt. Revert the
change to address the problem.
Fixes: 842067940a ("dmaengine: dw: Enable runtime PM")
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210203191924.15706-1-cezary.rojewski@intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add device state check before executing command. Without the check the
command can be issued while device is in halt state and causes the driver to
block while waiting for the completion of the command.
Reported-by: Sanjay Kumar <sanjay.k.kumar@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Tested-by: Sanjay Kumar <sanjay.k.kumar@intel.com>
Fixes: 0d5c10b4c8 ("dmaengine: idxd: add work queue drain support")
Link: https://lore.kernel.org/r/161219313921.2976211.12222625226450097465.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In 'dma_pool_create()', we return -ENOMEM, but don't release the resources
already allocated, as in all the other error handling paths.
Go to 'err_res_free' instead of returning directly.
Fixes: 0177947397 ("dmaengine: ti: k3-udma: Initial support for K3 BCDMA")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Link: https://lore.kernel.org/r/20210124070923.724479-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Nikhil reported the misc interrupt handler can sometimes miss handling
the command interrupt when an error interrupt happens near the same time.
Have the irq handling thread continue to process the misc interrupts until
all interrupts are processed. This is a low usage interrupt and is not
expected to handle high volume traffic. Therefore there is no concern of
this thread running for a long time.
Fixes: 0d5c10b4c8 ("dmaengine: idxd: add work queue drain support")
Reported-by: Nikhil Rao <nikhil.rao@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/161074755329.2183844.13295528344116907983.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In xilinx_dma_child_probe function, the nr_channels variable is
passed to of_property_read_u32() which expects an u32 return value
pointer. Modify the nr_channels variable type from int to u32 to
fix the incompatible parameter coverity warning.
Addresses-Coverity: Event incompatible_param.
Fixes: 1a9e7a03c7 ("dmaengine: vdma: Add support for mulit-channel dma mode")
Signed-off-by: Shravya Kumbham <shravya.kumbham@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/1608722462-29519-3-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
gcc points out an incorrect error handling loop:
drivers/dma/qcom/gpi.c: In function 'gpi_ch_init':
drivers/dma/qcom/gpi.c:1254:15: error: iteration 2 invokes undefined behavior [-Werror=aggressive-loop-optimizations]
1254 | struct gpii *gpii = gchan->gpii;
| ^~~~
drivers/dma/qcom/gpi.c:1951:2: note: within this loop
1951 | for (i = i - 1; i >= 0; i++) {
| ^~~
Change the loop to correctly walk backwards through the
initialized fields rather than off into the woods.
Fixes: 5d0c3533a1 ("dmaengine: qcom: Add GPI dma driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210103135738.3741123-1-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The parameter of kfree function is NULL, so kfree code is useless, delete it.
Therefore, goto expression is no longer needed, so simplify it.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201216130649.13979-1-zhengyongjun3@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If the dw_edma_alloc_burst() function fails then we free "chunk" but
it's still on the "desc->chunk->list" list so it will lead to a use
after free. Also the "->chunks_alloc" count is incremented when it
shouldn't be.
In current kernels small allocations are guaranteed to succeed and
dw_edma_alloc_burst() can't fail so this will not actually affect
runtime.
Fixes: e63d79d1ff ("dmaengine: Add Synopsys eDMA IP core driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Link: https://lore.kernel.org/r/X9dTBFrUPEvvW7qc@mwanda
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'disable_xdmac()' should be called in the error handling path of the
probe function to undo a previous 'enable_xdmac()' call, as already
done in the remove function.
Fixes: a6e9be055d ("dmaengine: milbeaut-xdmac: Add XDMAC driver for Milbeaut platforms")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201219132800.183254-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
'mtk_hsdma_hw_deinit()' should be called in the error handling path of the
probe function to undo a previous 'mtk_hsdma_hw_init()' call, as already
done in the remove function.
Fixes: 548c4597e9 ("dmaengine: mediatek: Add MediaTek High-Speed DMA controller for MT7622 and MT7623 SoC")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201219124718.182664-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Vinod Koul <vkoul@kernel.org>
drivers/dma/qcom/gpi.c:1419:3: warning: format '%lu' expects argument of
type 'long unsigned int', but argument 8 has type 'size_t {aka unsigned
int}' [-Wformat=]
drivers/dma/qcom/gpi.c:1427:31: warning: format '%lu' expects argument of
type 'long unsigned int', but argument 3 has type 'size_t {aka unsigned
int}' [-Wformat=]
drivers/dma/qcom/gpi.c:1447:3: warning: format '%llx' expects argument of
type 'long long unsigned int', but argument 4 has type 'dma_addr_t {aka
unsigned int}' [-Wformat=]
drivers/dma/qcom/gpi.c:1447:3: warning: format '%llx' expects argument of
type 'long long unsigned int', but argument 5 has type 'phys_addr_t {aka
unsigned int}' [-Wformat=]
Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201218104137.59200-1-nixiaoming@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The clean up is off by one so this will start at "i" and it should start
with "i - 1" and then it doesn't unregister the zeroeth elements in the
array.
Fixes: c52ca47823 ("dmaengine: idxd: add configuration component of driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/X9nFeojulsNqUSnG@mwanda
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Instead of initializing the rchan_tpl the initial commit re-initialized
the tchan_tpl.
Fixes: d2abc98233 ("dmaengine: ti: k3-udma: Initial support for K3 PKTDMA")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201216154833.20821-1-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
New drivers/devices
- Qualcomm ADM driver
- Qualcomm GPI driver
- Allwinner A100 DMA support
- Microchip Sama7g5 support
- Mediatek MT8516 apdma
- Updates:
- more updates to idxd driver and support for IAX config
- runtime PM support for dw driver
- TI keystone drivers for 5.11 included here due to dependency for TI
drivers
-----BEGIN PGP SIGNATURE-----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=uNBn
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"The last dmaengine updates for this year :)
This contains couple of new drivers, new device support and updates to
bunch of drivers.
New drivers/devices:
- Qualcomm ADM driver
- Qualcomm GPI driver
- Allwinner A100 DMA support
- Microchip Sama7g5 support
- Mediatek MT8516 apdma
Updates:
- more updates to idxd driver and support for IAX config
- runtime PM support for dw driver
- TI drivers"
* tag 'dmaengine-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (75 commits)
soc: ti: k3-ringacc: Use correct error casting in k3_ringacc_dmarings_init
dmaengine: ti: k3-udma-glue: Add support for K3 PKTDMA
dmaengine: ti: k3-udma: Initial support for K3 PKTDMA
dmaengine: ti: k3-udma: Add support for BCDMA channel TPL handling
dmaengine: ti: k3-udma: Initial support for K3 BCDMA
soc: ti: k3-ringacc: add AM64 DMA rings support.
dmaengine: ti: Add support for k3 event routers
dmaengine: ti: k3-psil: Add initial map for AM64
dmaengine: ti: k3-psil: Extend psil_endpoint_config for K3 PKTDMA
dt-bindings: dma: ti: Add document for K3 PKTDMA
dt-bindings: dma: ti: Add document for K3 BCDMA
dmaengine: dmatest: Use dmaengine_get_dma_device
dmaengine: doc: client: Update for dmaengine_get_dma_device() usage
dmaengine: Add support for per channel coherency handling
dmaengine: of-dma: Add support for optional router configuration callback
dmaengine: ti: k3-udma-glue: Configure the dma_dev for rings
dmaengine: ti: k3-udma-glue: Get the ringacc from udma_dev
dmaengine: ti: k3-udma-glue: Add function to get device pointer for DMA API
dmaengine: ti: k3-udma: Add support for second resource range from sysfw
dmaengine: ti: k3-udma: Wait for peer teardown completion if supported
...
This commit adds support for PKTDMA in k3-udma glue driver. Use new
psil_endpoint_config struct to get static data for a given channel or a
flow during setup. Make sure that the RX flows being mapped to a RX
channel is within the range of flows that is been allocated to that RX
channel.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-21-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
One of the DMAs introduced with AM64 is the Packet DMA (PKTDMA).
It serves similar purpose as K3 UDMAP channels in packet mode, but with
notable differences, like tflow support and channels being allocated to
service specific peripherals.
The rings for the PKTDMA is integrated within the DMA itself instead of
using rings from the general purpose ringacc.
PKTDMA can be used to service PSI-L peripherals, similarly to
K3 UDMA channels.
Most of the driver code can be reused for PKTDMA tchan/rchan support but
new setup and allocation functions are needed to handle the differences
between the DMAs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-20-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Unlike UDMAP the BCDMA defines the channel TPL levels per channel type.
In UDMAP the number of high and ultra-high channels applies to both tchan
and rchan.
BCDMA defines the TPL per channel types: bchan, tchan and rchan can have
different number of high and ultra-high channels.
In order to support BCDMA channel TPL we need to move the tpl information
as per channel type property for the DMAs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-19-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
One of the DMAs introduced with AM64 is the Block Copy DMA (BCDMA).
It serves similar purpose as K3 UDMAP channels in TR mode.
The rings for the BCDMA is integrated within the DMA itself instead of
using rings from the general purpose ringacc.
A BCDMA have two different type of channels:
- Block Copy Channels (bchan)
- Split Channels (tchan and rchan)
tchan and rchan can be used to service PSI-L peripherals, similarly to
K3 UDMA channels.
bchan can be only used for block copy operation (TR type15) like the
paired K3 UDMA tchan/rchan configured in block copy mode.
bchans can be also used to service peripherals directly if an external
trigger is selected for the channel.
Most of the driver code can be reused for BCDMA bchan/tchan/rchan support
but new setup and allocation functions are needed to handle the
differences between the DMAs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-18-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
By using the dmaengine_get_dma_device() to get the device for
dma_api use, the dmatest can support per channel coherency if it is
supported by the DMA controller.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-11-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Additional configuration for the DMA event router might be needed for a
channel which can not be done during device_alloc_chan_resources callback
since the router information is not yet present for the drivers.
If there is a need for additional configuration for the channel if DMA
router is in use, then the driver can implement the device_router_config
callback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-8-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Rings in RING mode should be using the DMA device for DMA API as in this
mode the ringacc will not access the ring memory in any ways, but the DMA
is.
Fix up the ring configuration and set the dma_dev unconditionally and let
the ringacc driver to select the correct device to use for DMA API.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-7-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If of_xudma_dev_get() returns with the valid udma_dev then the driver
already got the ringacc, there is no need to execute
of_k3_ringacc_get_by_phandle() for each channel via the glue layer.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-6-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Glue layer users should use the device of the DMA for DMA mapping and
allocations as it is the DMA which accesses to descriptors and buffers,
not the clients
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-5-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Resource allocation via sysfw can use up to two ranges per resource subtype
to support more complex resource assignment, mainly for DMA channels.
Take the second range also into consideration when setting up the maps for
available resources.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-4-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Set the TDTYPE if it is supported on the platform (j721e) which will cause
UDMAP to wait for the remote peer to finish the teardown before returning
the teardown completed message.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-3-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
According to different sections of the TRM, the hchan_cnt of CAP3 includes
the number of uchan in UDMA, thus the start offset of the normal channels
are hchan_cnt.
Fixes: daf4ad0499 ("dmaengine: ti: k3-udma: Query throughput level information from hardware")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20201208090440.31792-2-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To avoid multiple entries in MDMA interrupt handler for each flag&interrupt
enable, manage all flags set at once.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20201120143320.30367-5-amelie.delaunay@st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
DMA_SxPAR or DMA_SxM0AR/M1AR registers have to be aligned on PSIZE or MSIZE
respectively. This means that bus width needs to be forced to 1 byte when
computed width is not aligned with address.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20201120143320.30367-4-amelie.delaunay@st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When dma_channel_release is called, it means that the channel won't be used
anymore with the configuration it had. To ensure a future client can safely
use the channel after it has been released, clean the configuration done
when channel was requested.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20201120143320.30367-3-amelie.delaunay@st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
To better understand error that can be detected by the DMA controller,
manage the error flags before the transfer flags.
This way, it is possible to know if the FIFO error flag is set for an
over/underrun condition or a FIFO level error.
When a FIFO over/underrun condition occurs, the data is not lost because
peripheral request is not acknowledged by the stream until the over/
underrun condition is cleared. If this acknowledge takes too much time,
the peripheral itself may detect an over/underrun condition of its internal
buffer and data might be lost.
That's why in case the FIFO error flag is set, we check if the channel is
disabled or not, and if a Transfer Complete flag is set, which means that
the channel is disabled because of the end of transfer.
Because channel is disabled by hardware either by a FIFO level error, or by
an end of transfer.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20201120143320.30367-2-amelie.delaunay@st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
While performing suspend/resume, we were getting below kernel crash.
[ 54.541672] [FTS][Info]gesture suspend...
[ 54.605256] [FTS][Error][GESTURE]Enter into gesture(suspend) failed!
[ 54.605256]
[ 58.345850] irq event 10: bogus return value fffffff3
......
[ 58.345966] [<ffff0000080830f0>] el1_irq+0xb0/0x124
[ 58.345971] [<ffff000008085360>] arch_cpu_idle+0x10/0x18
[ 58.345975] [<ffff0000081077f4>] do_idle+0x1ac/0x1e0
[ 58.345979] [<ffff0000081079c8>] cpu_startup_entry+0x20/0x28
[ 58.345983] [<ffff000008a80ed0>] rest_init+0xd0/0xdc
[ 58.345988] [<ffff0000091c0b48>] start_kernel+0x390/0x3a4
[ 58.345990] handlers:
[ 58.345994] [<ffff0000085120d0>] bam_dma_irq
The reason for the crash we found is, bam_dma_irq() was returning
negative value when the device resumes in some conditions.
In addition, the irq handler should have one of the below return values.
IRQ_NONE interrupt was not from this device or was not handled
IRQ_HANDLED interrupt was handled by this device
IRQ_WAKE_THREAD handler requests to wake the handler thread
Therefore, to resolve this crash, we have changed the return value to
IRQ_NONE.
Signed-off-by: Parth Y Shah <sparth1292@gmail.com>
Link: https://lore.kernel.org/r/1607322820-7450-1-git-send-email-sparth1292@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support to allow configuration of Intel Analytics Accelerator (IAX) in
addition to the Intel Data Streaming Accelerator (DSA). The IAX hardware
has the same configuration interface as DSA. The main difference
is the type of operations it performs. We can support the DSA and
IAX devices on the same driver with some tweaks.
IAX has a 64B completion record that needs to be 64B aligned, as opposed to
a 32B completion record that is 32B aligned for DSA. IAX also does not
support token management.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/160564555488.1834439.4261958859935360473.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Update the kerneldoc function headers to fix build warnings:
drivers/dma/qcom/qcom_adm.c:180: warning: Function parameter or member 'chan' not described in 'adm_free_chan'
drivers/dma/qcom/qcom_adm.c:190: warning: Function parameter or member 'burst' not described in 'adm_get_blksize'
drivers/dma/qcom/qcom_adm.c:466: warning: Function parameter or member 'chan' not described in 'adm_terminate_all'
drivers/dma/qcom/qcom_adm.c:466: warning: Excess function parameter 'achan' description in 'adm_terminate_all'
drivers/dma/qcom/qcom_adm.c:503: warning: Function parameter or member 'achan' not described in 'adm_start_dma'
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Link: https://lore.kernel.org/r/20201126184602.GA1008@earth.li
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver can match only via the DT table so the main table should be
always used and the of_match_ptr does not have any sense (this also
allows ACPI matching via PRP0001, even though it is not relevant here).
The secondary match of_device_id tables (passed to of_match_node) should
be marked as maybe unused to fix compile testing (!CONFIG_OF on x86_64)
warnings:
drivers/dma/ti/dma-crossbar.c:125:34: warning:
‘ti_am335x_master_match’ defined but not used [-Wunused-const-variable=]
drivers/dma/ti/dma-crossbar.c:22:34: warning:
‘ti_dma_xbar_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201120162303.482126-6-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver uses a second of_device_id table in the probe()
function by passing it to of_match_node(). This code will be a no-op
for compile testing (!CONFIG_OF on x86_64):
drivers/dma/stm32-dmamux.c:171:34: warning:
‘stm32_stm32dma_master_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201120162303.482126-5-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/dma/sf-pdma/sf-pdma.c:576:34: warning:
‘sf_pdma_dt_ids’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201120162303.482126-4-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/dma/mv_xor.c:1281:34: warning:
‘mv_xor_dt_ids’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201120162303.482126-3-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/dma/dw-axi-dmac/dw-axi-dmac-platform.c:984:34: warning:
‘dw_dma_of_id_table’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201120162303.482126-2-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/dma/dma-jz4780.c:1031:34: warning:
‘jz4780_dma_dt_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201120162303.482126-1-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The mxs-dma driver is only used by DT platforms and the .id_table
is unused.
Get rid of it to simplify the code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201123193051.17285-1-festevam@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Since 5.10-rc1 i.MX is a devicetree-only platform, so simplify the code
by removing the unused non-DT support.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201124143405.2764-1-festevam@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This controller provides DMAengine capabilities for a variety of peripheral
buses such as I2C, UART, and SPI. By using GPI dmaengine driver, bus
drivers can use a standardize interface that is protocol independent to
transfer data between memory and peripheral.
Link: https://lore.kernel.org/r/20201109085450.24843-4-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Cezary Rojewski