Make the PFVF send function device specific.
This is in preparation for the introduction of PFVF support in the
qat_4xxx driver since the send logic differs between QAT GEN2 and
QAT GEN4 devices.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add the function get_vf2pf_offset() to adf_pfvf_ops to differentiate the
CSRs used for pf2vf and vf2pf.
Offsets may or may not be direction specific depending on QAT
generation. Since in QAT GEN2 the CSR is not direction specific, i.e.
there is a single mailbox register shared for pf2vf and vf2pf, both
get_vf2pf_offset() and get_vf2pf_offset() will return the same offset.
This change is to make the direction explicit, so it is easier to
understand and debug and also in preparation for the introduction of
PFVF support in the qat_4xxx driver since QAT GEN4 devices have a
separate CSR for pf2vf and vf2pf communications.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add pfvf_ops structure to isolate PFVF related functions inside the
adf_hw_device_data structure.
For GEN2, the structure is populated using one of the two helper
functions, adf_gen2_init_pf_pfvf_ops() or adf_gen2_init_vf_pfvf_ops(),
for the PF and VF driver respectively.
For the DH895XCC PF driver, the structure is populated using
adf_gen2_init_pf_pfvf_ops() but some of the functions are then
overwritten.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move the function pfvf_comms_disabled() from the qat_4xxx module to
intel_qat as it will be used by other components to keep the PFVF
feature disabled.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move device specific PFVF logic related to the VF to the newly created
adf_gen2_pfvf.c.
This refactory is done to isolate the GEN2 PFVF code into its own file
in preparation for the introduction of support for PFVF for GEN4
devices.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Reviewed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move device specific PFVF logic related to the PF to the newly created
adf_gen2_pfvf.c.
This refactory is done to isolate the GEN2 PFVF code into its own file
in preparation for the introduction of support for PFVF for GEN4
devices.
In addition the PFVF PF logic for dh895xcc has been isolated to
adf_dh895xcc_hw_data.c.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Rework __adf_iov_putmsg() to handle retries due to collisions
internally, removing the need for an external retry loop.
The functions __adf_iov_putmsg() and adf_iov_putmsg() have been merged
together maintaining the adf_iov_putmsg() name.
This will allow to use this function only for GEN2 devices, since
collision are peculiar of this generation and therefore should be
confined to the actual implementation of the transport/medium access.
Note that now adf_iov_putmsg() will retry to send a message only in case
of collisions and will now fail if an ACK is not received from the
remote function.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Refactor the receive and handle logic to separate the parsing and
handling of the PFVF message from the initial retrieval and ACK.
This is to allow the intoduction of the recv function in a subsequent
patch.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If a PFVF message with MSGORIGIN_SYSTEM not set is received, re-enable
interrupts allowing the processing of new messages.
This is to simplify the refactoring of the recv function in a subsequent
patch.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Change the PFVF receipt flow on the VF side to read, ack and handle the
message instead of read, handle and ack.
This is done for (1) consistency with the PF side, see the function
adf_recv_and_handle_vf2pf_msg() in adf_pf2vf_msg.c, and (2) performance
reasons, to avoid keeping the CSR busy while parsing the message.
In addition, do not ACK PFVF legacy messages, as this driver is not
capable of handling PFVF legacy messages.
If a PFVF message with MSGORIGIN not set is received, do nothing.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move the interrupt handling call from the PF specific protocol file,
adf_pf2vf_msg.c, to adf_sriov.c to maintain the PFVF files focused on
the protocol handling.
The function adf_vf2pf_req_hndl() has been renamed as
adf_recv_and_handle_vf2pf_msg() to reflect its actual purpose and
maintain consistency with the VF side. This function now returns a
boolean indicating to the caller if interrupts need to be re-enabled or
not.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move the reading and parsing of a PF2VF message from the bottom half
function in adf_vf_isr.c, adf_pf2vf_bh_handler(), to the PFVF protocol
file adf_vf2pf_msg.c, for better code organization.
The receive and handle logic has been moved to a new function called
adf_recv_and_handle_pf2vf_msg() which returns a boolean indicating if
interrupts need to be re-enabled or not.
A slight refactoring has been done to avoid calculating the PF2VF CSR
offset twice and repeating the clearing of the PF2VFINT bit.
The "PF restarting" logic, now defined in the function
adf_pf2vf_handle_pf_restaring(), has been kept in adf_vf_isr.c due to
the dependencies with the adf_vf_stop_wq workqueue.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move vf2pf interrupt enable and disable functions from adf_pf2vf_msg.c
to adf_isr.c
This it to separate the interrupt related code from the PFVF protocol
logic.
With this change, the function adf_disable_vf2pf_interrupts_irq() is
only called from adf_isr.c and it has been marked as static.
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Reviewed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Move logic associated to handling VF2PF interrupt to its own function.
This will simplify the handling of multiple interrupt sources in the
function adf_msix_isr_ae() in the future.
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Co-developed-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If the remote function did not ACK the reception of a message, the
function __adf_iov_putmsg() could detect it as a collision.
This was due to the fact that the collision and the timeout checks after
the ACK loop were in the wrong order. The timeout must be checked at the
end of the loop, so fix by swapping the order of the two checks.
Fixes: 9b768e8a39 ("crypto: qat - detect PFVF collision after ACK")
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Co-developed-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Marco Chiappero <marco.chiappero@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The QAT driver does not have support for PFVF interrupts for GEN4
devices, therefore report the vf2pf sources as 0.
This prevents a NULL pointer dereference in the function
adf_msix_isr_ae() if the device triggers a spurious interrupt.
Fixes: 993161d36a ("crypto: qat - fix handling of VF to PF interrupts")
Reported-by: Adam Guerin <adam.guerin@intel.com>
Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In contrast to the fully prediction resistant 'pr' DRBGs, the 'nopr'
variants get seeded once at boot and reseeded only rarely thereafter,
namely only after 2^20 requests have been served each. AFAICT, this
reseeding based on the number of requests served is primarily motivated
by information theoretic considerations, c.f. NIST SP800-90Ar1,
sec. 8.6.8 ("Reseeding").
However, given the relatively large seed lifetime of 2^20 requests, the
'nopr' DRBGs can hardly be considered to provide any prediction resistance
whatsoever, i.e. to protect against threats like side channel leaks of the
internal DRBG state (think e.g. leaked VM snapshots). This is expected and
completely in line with the 'nopr' naming, but as e.g. the
"drbg_nopr_hmac_sha512" implementation is potentially being used for
providing the "stdrng" and thus, the crypto_default_rng serving the
in-kernel crypto, it would certainly be desirable to achieve at least the
same level of prediction resistance as get_random_bytes() does.
Note that the chacha20 rngs underlying get_random_bytes() get reseeded
every CRNG_RESEED_INTERVAL == 5min: the secondary, per-NUMA node rngs from
the primary one and the primary rng in turn from the entropy pool, provided
sufficient entropy is available.
The 'nopr' DRBGs do draw randomness from get_random_bytes() for their
initial seed already, so making them to reseed themselves periodically from
get_random_bytes() in order to let them benefit from the latter's
prediction resistance is not such a big change conceptually.
In principle, it would have been also possible to make the 'nopr' DRBGs to
periodically invoke a full reseeding operation, i.e. to also consider the
jitterentropy source (if enabled) in addition to get_random_bytes() for the
seed value. However, get_random_bytes() is relatively lightweight as
compared to the jitterentropy generation process and thus, even though the
'nopr' reseeding is supposed to get invoked infrequently, it's IMO still
worthwhile to avoid occasional latency spikes for drbg_generate() and
stick to get_random_bytes() only. As an additional remark, note that
drawing randomness from the non-SP800-90B-conforming get_random_bytes()
only won't adversely affect SP800-90A conformance either: the very same is
being done during boot via drbg_seed_from_random() already once
rng_is_initialized() flips to true and it follows that if the DRBG
implementation does conform to SP800-90A now, it will continue to do so.
Make the 'nopr' DRBGs to reseed themselves periodically from
get_random_bytes() every CRNG_RESEED_INTERVAL == 5min.
More specifically, introduce a new member ->last_seed_time to struct
drbg_state for recording in units of jiffies when the last seeding
operation had taken place. Make __drbg_seed() maintain it and let
drbg_generate() invoke a reseed from get_random_bytes() via
drbg_seed_from_random() if more than 5min have passed by since the last
seeding operation. Be careful to not to reseed if in testing mode though,
or otherwise the drbg related tests in crypto/testmgr.c would fail to
reproduce the expected output.
In order to keep the formatting clean in drbg_generate() wrap the logic
for deciding whether or not a reseed is due in a new helper,
drbg_nopr_reseed_interval_elapsed().
Signed-off-by: Nicolai Stange <nstange@suse.de>
Reviewed-by: Stephan Müller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Now that drbg_prepare_hrng() doesn't do anything but to instantiate a
jitterentropy crypto_rng instance, it looks a little odd to have the
related error handling at its only caller, drbg_instantiate().
Move the handling of jitterentropy allocation failures from
drbg_instantiate() close to the allocation itself in drbg_prepare_hrng().
There is no change in behaviour.
Signed-off-by: Nicolai Stange <nstange@suse.de>
Reviewed-by: Stephan Müller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
get_random_bytes() usually hasn't full entropy available by the time DRBG
instances are first getting seeded from it during boot. Thus, the DRBG
implementation registers random_ready_callbacks which would in turn
schedule some work for reseeding the DRBGs once get_random_bytes() has
sufficient entropy available.
For reference, the relevant history around handling DRBG (re)seeding in
the context of a not yet fully seeded get_random_bytes() is:
commit 16b369a91d ("random: Blocking API for accessing
nonblocking_pool")
commit 4c7879907e ("crypto: drbg - add async seeding operation")
commit 205a525c33 ("random: Add callback API for random pool
readiness")
commit 57225e6797 ("crypto: drbg - Use callback API for random
readiness")
commit c2719503f5 ("random: Remove kernel blocking API")
However, some time later, the initialization state of get_random_bytes()
has been made queryable via rng_is_initialized() introduced with commit
9a47249d44 ("random: Make crng state queryable"). This primitive now
allows for streamlining the DRBG reseeding from get_random_bytes() by
replacing that aforementioned asynchronous work scheduling from
random_ready_callbacks with some simpler, synchronous code in
drbg_generate() next to the related logic already present therein. Apart
from improving overall code readability, this change will also enable DRBG
users to rely on wait_for_random_bytes() for ensuring that the initial
seeding has completed, if desired.
The previous patches already laid the grounds by making drbg_seed() to
record at each DRBG instance whether it was being seeded at a time when
rng_is_initialized() still had been false as indicated by
->seeded == DRBG_SEED_STATE_PARTIAL.
All that remains to be done now is to make drbg_generate() check for this
condition, determine whether rng_is_initialized() has flipped to true in
the meanwhile and invoke a reseed from get_random_bytes() if so.
Make this move:
- rename the former drbg_async_seed() work handler, i.e. the one in charge
of reseeding a DRBG instance from get_random_bytes(), to
"drbg_seed_from_random()",
- change its signature as appropriate, i.e. make it take a struct
drbg_state rather than a work_struct and change its return type from
"void" to "int" in order to allow for passing error information from
e.g. its __drbg_seed() invocation onwards to callers,
- make drbg_generate() invoke this drbg_seed_from_random() once it
encounters a DRBG instance with ->seeded == DRBG_SEED_STATE_PARTIAL by
the time rng_is_initialized() has flipped to true and
- prune everything related to the former, random_ready_callback based
mechanism.
As drbg_seed_from_random() is now getting invoked from drbg_generate() with
the ->drbg_mutex being held, it must not attempt to recursively grab it
once again. Remove the corresponding mutex operations from what is now
drbg_seed_from_random(). Furthermore, as drbg_seed_from_random() can now
report errors directly to its caller, there's no need for it to temporarily
switch the DRBG's ->seeded state to DRBG_SEED_STATE_UNSEEDED so that a
failure of the subsequently invoked __drbg_seed() will get signaled to
drbg_generate(). Don't do it then.
Signed-off-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Since commit 42ea507fae ("crypto: drbg - reseed often if seedsource is
degraded"), the maximum seed lifetime represented by ->reseed_threshold
gets temporarily lowered if the get_random_bytes() source cannot provide
sufficient entropy yet, as is common during boot, and restored back to
the original value again once that has changed.
More specifically, if the add_random_ready_callback() invoked from
drbg_prepare_hrng() in the course of DRBG instantiation does not return
-EALREADY, that is, if get_random_bytes() has not been fully initialized
at this point yet, drbg_prepare_hrng() will lower ->reseed_threshold
to a value of 50. The drbg_async_seed() scheduled from said
random_ready_callback will eventually restore the original value.
A future patch will replace the random_ready_callback based notification
mechanism and thus, there will be no add_random_ready_callback() return
value anymore which could get compared to -EALREADY.
However, there's __drbg_seed() which gets invoked in the course of both,
the DRBG instantiation as well as the eventual reseeding from
get_random_bytes() in aforementioned drbg_async_seed(), if any. Moreover,
it knows about the get_random_bytes() initialization state by the time the
seed data had been obtained from it: the new_seed_state argument introduced
with the previous patch would get set to DRBG_SEED_STATE_PARTIAL in case
get_random_bytes() had not been fully initialized yet and to
DRBG_SEED_STATE_FULL otherwise. Thus, __drbg_seed() provides a convenient
alternative for managing that ->reseed_threshold lowering and restoring at
a central place.
Move all ->reseed_threshold adjustment code from drbg_prepare_hrng() and
drbg_async_seed() respectively to __drbg_seed(). Make __drbg_seed()
lower the ->reseed_threshold to 50 in case its new_seed_state argument
equals DRBG_SEED_STATE_PARTIAL and let it restore the original value
otherwise.
There is no change in behaviour.
Signed-off-by: Nicolai Stange <nstange@suse.de>
Reviewed-by: Stephan Müller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Currently, the DRBG implementation schedules asynchronous works from
random_ready_callbacks for reseeding the DRBG instances with output from
get_random_bytes() once the latter has sufficient entropy available.
However, as the get_random_bytes() initialization state can get queried by
means of rng_is_initialized() now, there is no real need for this
asynchronous reseeding logic anymore and it's better to keep things simple
by doing it synchronously when needed instead, i.e. from drbg_generate()
once rng_is_initialized() has flipped to true.
Of course, for this to work, drbg_generate() would need some means by which
it can tell whether or not rng_is_initialized() has flipped to true since
the last seeding from get_random_bytes(). Or equivalently, whether or not
the last seed from get_random_bytes() has happened when
rng_is_initialized() was still evaluating to false.
As it currently stands, enum drbg_seed_state allows for the representation
of two different DRBG seeding states: DRBG_SEED_STATE_UNSEEDED and
DRBG_SEED_STATE_FULL. The former makes drbg_generate() to invoke a full
reseeding operation involving both, the rather expensive jitterentropy as
well as the get_random_bytes() randomness sources. The DRBG_SEED_STATE_FULL
state on the other hand implies that no reseeding at all is required for a
!->pr DRBG variant.
Introduce the new DRBG_SEED_STATE_PARTIAL state to enum drbg_seed_state for
representing the condition that a DRBG was being seeded when
rng_is_initialized() had still been false. In particular, this new state
implies that
- the given DRBG instance has been fully seeded from the jitterentropy
source (if enabled)
- and drbg_generate() is supposed to reseed from get_random_bytes()
*only* once rng_is_initialized() turns to true.
Up to now, the __drbg_seed() helper used to set the given DRBG instance's
->seeded state to constant DRBG_SEED_STATE_FULL. Introduce a new argument
allowing for the specification of the to be written ->seeded value instead.
Make the first of its two callers, drbg_seed(), determine the appropriate
value based on rng_is_initialized(). The remaining caller,
drbg_async_seed(), is known to get invoked only once rng_is_initialized()
is true, hence let it pass constant DRBG_SEED_STATE_FULL for the new
argument to __drbg_seed().
There is no change in behaviour, except for that the pr_devel() in
drbg_generate() would now report "unseeded" for ->pr DRBG instances which
had last been seeded when rng_is_initialized() was still evaluating to
false.
Signed-off-by: Nicolai Stange <nstange@suse.de>
Reviewed-by: Stephan Müller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There are two different randomness sources the DRBGs are getting seeded
from, namely the jitterentropy source (if enabled) and get_random_bytes().
At initial DRBG seeding time during boot, the latter might not have
collected sufficient entropy for seeding itself yet and thus, the DRBG
implementation schedules a reseed work from a random_ready_callback once
that has happened. This is particularly important for the !->pr DRBG
instances, for which (almost) no further reseeds are getting triggered
during their lifetime.
Because collecting data from the jitterentropy source is a rather expensive
operation, the aforementioned asynchronously scheduled reseed work
restricts itself to get_random_bytes() only. That is, it in some sense
amends the initial DRBG seed derived from jitterentropy output at full
(estimated) entropy with fresh randomness obtained from get_random_bytes()
once that has been seeded with sufficient entropy itself.
With the advent of rng_is_initialized(), there is no real need for doing
the reseed operation from an asynchronously scheduled work anymore and a
subsequent patch will make it synchronous by moving it next to related
logic already present in drbg_generate().
However, for tracking whether a full reseed including the jitterentropy
source is required or a "partial" reseed involving only get_random_bytes()
would be sufficient already, the boolean struct drbg_state's ->seeded
member must become a tristate value.
Prepare for this by introducing the new enum drbg_seed_state and change
struct drbg_state's ->seeded member's type from bool to that type.
For facilitating review, enum drbg_seed_state is made to only contain
two members corresponding to the former ->seeded values of false and true
resp. at this point: DRBG_SEED_STATE_UNSEEDED and DRBG_SEED_STATE_FULL. A
third one for tracking the intermediate state of "seeded from jitterentropy
only" will be introduced with a subsequent patch.
There is no change in behaviour at this point.
Signed-off-by: Nicolai Stange <nstange@suse.de>
Reviewed-by: Stephan Müller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Static variables do not need to be initialized to 0.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
'destroy_workqueue()' already drains the queue before destroying it, so
there is no need to flush it explicitly.
Remove the redundant 'flush_workqueue()' calls.
This was generated with coccinelle:
@@
expression E;
@@
- flush_workqueue(E);
destroy_workqueue(E);
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Acked-by: Gilad Ben-Yossef <gilad@benyossef.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix the following coccicheck REVIEW:
./drivers/crypto/marvell/octeontx2/otx2_cptvf_algs.c:1688:16-17 use swap() to make code cleaner
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: chiminghao <chi.minghao@zte.com.cn>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
According to the BER encoding rules, integer value should be encoded
as two's complement, and if the highest bit of a positive integer
is 1, should add a leading zero-octet.
The kernel's built-in RSA algorithm cannot recognize negative numbers
when parsing keys, so it can pass this test case.
Export the key to file and run the following command to verify the
fix result:
openssl asn1parse -inform DER -in /path/to/key/file
Signed-off-by: Lei He <helei.sig11@bytedance.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pointer alg points to sub field of tmpl, it
is dereferenced after tmpl is freed. Fix
this by accessing alg before free tmpl.
Fixes: ec8f5d8f ("crypto: qce - Qualcomm crypto engine driver")
Signed-off-by: Chengfeng Ye <cyeaa@connect.ust.hk>
Acked-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pointer base points to sub field of tmpl, it
is dereferenced after tmpl is freed. Fix
this by accessing base before free tmpl.
Fixes: ec8f5d8f ("crypto: qce - Qualcomm crypto engine driver")
Signed-off-by: Chengfeng Ye <cyeaa@connect.ust.hk>
Acked-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pointer alg points to sub field of tmpl, it
is dereferenced after tmpl is freed. Fix
this by accessing alg before free tmpl.
Fixes: 9363efb4 ("crypto: qce - Add support for AEAD algorithms")
Signed-off-by: Chengfeng Ye <cyeaa@connect.ust.hk>
Acked-by: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use the macro 'swap()' defined in 'include/linux/minmax.h' to avoid
opencoding it.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Yang Guang <yang.guang5@zte.com.cn>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit c9f608c380 ("crypto: keembay-ocs-ecc - Add Keem Bay OCS ECC
Driver") only adds drivers/crypto/keembay/keembay-ocs-ecc.c, but adds a
file entry drivers/crypto/keembay/ocs-ecc-curve-defs.h in MAINTAINERS.
Hence, ./scripts/get_maintainer.pl --self-test=patterns warns:
warning: no file matches F: drivers/crypto/keembay/ocs-ecc-curve-defs.h
Assuming that this header is obsolete and will not be included in the
repository, remove the unneeded file entry from MAINTAINERS.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix to return negative error code -ENOMEM from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: c9f608c380 ("crypto: keembay-ocs-ecc - Add Keem Bay OCS ECC Driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When enable the kernel debug config, there is below calltrace detected:
BUG: using smp_processor_id() in preemptible [00000000] code: cryptomgr_test/339
caller is debug_smp_processor_id+0x20/0x30
CPU: 9 PID: 339 Comm: cryptomgr_test Not tainted 5.10.63-yocto-standard #1
Hardware name: NXP Layerscape LX2160ARDB (DT)
Call trace:
dump_backtrace+0x0/0x1a0
show_stack+0x24/0x30
dump_stack+0xf0/0x13c
check_preemption_disabled+0x100/0x110
debug_smp_processor_id+0x20/0x30
dpaa2_caam_enqueue+0x10c/0x25c
......
cryptomgr_test+0x38/0x60
kthread+0x158/0x164
ret_from_fork+0x10/0x38
According to the comment in commit ac5d15b4519f("crypto: caam/qi2
- use affine DPIOs "), because preemption is no longer disabled
while trying to enqueue an FQID, it might be possible to run the
enqueue on a different CPU(due to migration, when in process context),
however this wouldn't be a functionality issue. But there will be
above calltrace when enable kernel debug config. So, replace this_cpu_ptr
with raw_cpu_ptr to avoid above call trace.
Fixes: ac5d15b451 ("crypto: caam/qi2 - use affine DPIOs")
Cc: stable@vger.kernel.org
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This RNG device is present on Marvell OcteonTx2 silicons as well and
also provides entropy health status.
HW continuously checks health condition of entropy and reports
faults. Fault is in terms of co-processor cycles since last fault
detected. This doesn't get cleared and only updated when new fault
is detected. Also there are chances of detecting false positives.
So to detect a entropy failure SW has to check if failures are
persistent ie cycles elapsed is frequently updated by HW.
This patch adds support to detect health failures using below algo.
1. Consider any fault detected before 10ms as a false positive and ignore.
10ms is chosen randomly, no significance.
2. Upon first failure detection make a note of cycles elapsed and when this
error happened in realtime (cntvct).
3. Upon subsequent failure, check if this is new or a old one by comparing
current cycles with the ones since last failure. cycles or time since
last failure is calculated using cycles and time info captured at (2).
HEALTH_CHECK status register is not available to VF, hence had to map
PF registers. Also since cycles are in terms of co-processor cycles,
had to retrieve co-processor clock rate from RST device.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In case there were more requests from different tfms in the crypto
queue, only the context of the last initialized tfm was considered.
Fixes: ec2088b66f ("crypto: atmel-aes - Allocate aes dev at tfm init time")
Reported-by: Wolfgang Ocker <weo@reccoware.de>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add Kconfig support for -Wimplicit-fallthrough for both GCC and Clang.
The compiler option is under configuration CC_IMPLICIT_FALLTHROUGH,
which is enabled by default.
Special thanks to Nathan Chancellor who fixed the Clang bug[1][2]. This
bugfix only appears in Clang 14.0.0, so older versions still contain
the bug and -Wimplicit-fallthrough won't be enabled for them, for now.
This concludes a long journey and now we are finally getting rid
of the unintentional fallthrough bug-class in the kernel, entirely. :)
Link: 9ed4a94d64 [1]
Link: https://bugs.llvm.org/show_bug.cgi?id=51094 [2]
Link: https://github.com/KSPP/linux/issues/115
Link: https://github.com/ClangBuiltLinux/linux/issues/236
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Co-developed-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Clean up open-coded swap() calls.
* A little bit of #ifdef golf to complete the reunification of the
kernel and userspace libxfs source code.
-----BEGIN PGP SIGNATURE-----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=wsFu
-----END PGP SIGNATURE-----
Merge tag 'xfs-5.16-merge-5' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs cleanups from Darrick Wong:
"The most 'exciting' aspect of this branch is that the xfsprogs
maintainer and I have worked through the last of the code
discrepancies between kernel and userspace libxfs such that there are
no code differences between the two except for #includes.
IOWs, diff suffices to demonstrate that the userspace tools behave the
same as the kernel, and kernel-only bits are clearly marked in the
/kernel/ source code instead of just the userspace source.
Summary:
- Clean up open-coded swap() calls.
- A little bit of #ifdef golf to complete the reunification of the
kernel and userspace libxfs source code"
* tag 'xfs-5.16-merge-5' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: sync xfs_btree_split macros with userspace libxfs
xfs: #ifdef out perag code for userspace
xfs: use swap() to make dabtree code cleaner
Fix a build error in stracktrace.c, fix resolving of addresses to
function names in backtraces, fix single-stepping in assembly code
and flush userspace pte's when using set_pte_at().
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCYZAyIAAKCRD3ErUQojoP
X8zUAQCV4fijXlUEOnZorH42QsSvs1SowHXu2YdHU8CmauWVawEAt14Zj3fmMBcS
+uSacieZROU9maQtGgJAYHZVJwgPyQY=
=OQRw
-----END PGP SIGNATURE-----
Merge tag 'for-5.16/parisc-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull more parisc fixes from Helge Deller:
"Fix a build error in stracktrace.c, fix resolving of addresses to
function names in backtraces, fix single-stepping in assembly code and
flush userspace pte's when using set_pte_at()"
* tag 'for-5.16/parisc-3' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc/entry: fix trace test in syscall exit path
parisc: Flush kernel data mapping in set_pte_at() when installing pte for user page
parisc: Fix implicit declaration of function '__kernel_text_address'
parisc: Fix backtrace to always include init funtion names
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJhkUvoAAoJELcQ+SIFb8HaQG8H/1pF/zhT+xYAK7dMOYfdyl9R
UGgnNGR2kjPDhsAkMHIYWVopP2KFV4kA4TCe8UcEt4GPeWZgGjV8lIaHJa/kdUsH
5tyRYtC8ZtVhJMVJQ8jZYZcTwOqYFFGtCksPq6/j0dHE0Gf+nQStSXNZqi8/XxE9
c3jDg+l7PVwdl7LWFedPVXcflhD5JLrRhyA/17V0INWrqP/MboXGRyq/Yluksw7x
C89ZXrgRE+5tN9icfRT4pl/XBpezWQkjuvsyHM9DWOjqICXfng8yeB5MZ/+R2uyF
qbXRSGqICOFhRRV9m/L0kypCYYiaZ8bBiYvLeGNggmpUJVMosIDFpS7kiYQavuA=
=dnw0
-----END PGP SIGNATURE-----
Merge tag 'sh-for-5.16' of git://git.libc.org/linux-sh
Pull arch/sh updates from Rich Felker.
* tag 'sh-for-5.16' of git://git.libc.org/linux-sh:
sh: pgtable-3level: Fix cast to pointer from integer of different size
sh: fix READ/WRITE redefinition warnings
sh: define __BIG_ENDIAN for math-emu
sh: math-emu: drop unused functions
sh: fix kconfig unmet dependency warning for FRAME_POINTER
sh: Cleanup about SPARSE_IRQ
sh: kdump: add some attribute to function
maple: fix wrong return value of maple_bus_init().
sh: boot: avoid unneeded rebuilds under arch/sh/boot/compressed/
sh: boot: add intermediate vmlinux.bin* to targets instead of extra-y
sh: boards: Fix the cacography in irq.c
sh: check return code of request_irq
sh: fix trivial misannotations
- Fix early_iounmap
- Drop cc-option fallbacks for architecture selection
-----BEGIN PGP SIGNATURE-----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=Ksk/
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
- Fix early_iounmap
- Drop cc-option fallbacks for architecture selection
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9156/1: drop cc-option fallbacks for architecture selection
ARM: 9155/1: fix early early_iounmap()
- 2 fixes due to DT node name changes on Arm, Ltd. boards
- Treewide rename of Ingenic CGU headers
- Update ST email addresses
- Remove Netlogic DT bindings
- Dropping few more cases of redundant 'maxItems' in schemas
- Convert toshiba,tc358767 bridge binding to schema
-----BEGIN PGP SIGNATURE-----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=ukBC
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Two fixes due to DT node name changes on Arm, Ltd. boards
- Treewide rename of Ingenic CGU headers
- Update ST email addresses
- Remove Netlogic DT bindings
- Dropping few more cases of redundant 'maxItems' in schemas
- Convert toshiba,tc358767 bridge binding to schema
* tag 'devicetree-fixes-for-5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: watchdog: sunxi: fix error in schema
bindings: media: venus: Drop redundant maxItems for power-domain-names
dt-bindings: Remove Netlogic bindings
clk: versatile: clk-icst: Ensure clock names are unique
of: Support using 'mask' in making device bus id
dt-bindings: treewide: Update @st.com email address to @foss.st.com
dt-bindings: media: Update maintainers for st,stm32-hwspinlock.yaml
dt-bindings: media: Update maintainers for st,stm32-cec.yaml
dt-bindings: mfd: timers: Update maintainers for st,stm32-timers
dt-bindings: timer: Update maintainers for st,stm32-timer
dt-bindings: i2c: imx: hardware do not restrict clock-frequency to only 100 and 400 kHz
dt-bindings: display: bridge: Convert toshiba,tc358767.txt to yaml
dt-bindings: Rename Ingenic CGU headers to ingenic,*.h
timer delivery stops working for a new child task because copy_process()
copies state information which is only valid for the parent task.
-----BEGIN PGP SIGNATURE-----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=EBbc
-----END PGP SIGNATURE-----
Merge tag 'timers-urgent-2021-11-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Thomas Gleixner:
"A single fix for POSIX CPU timers to address a problem where POSIX CPU
timer delivery stops working for a new child task because
copy_process() copies state information which is only valid for the
parent task"
* tag 'timers-urgent-2021-11-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
posix-cpu-timers: Clear task::posix_cputimers_work in copy_process()
- Core code:
A regression fix for the Open Firmware interrupt mapping code where a
interrupt controller property in a node caused a map property in the
same node to be ignored.
- Interrupt chip drivers:
- Workaround a limitation in SiFive PLIC interrupt chip which silently
ignores an EOI when the interrupt line is masked.
- Provide the missing mask/unmask implementation for the CSKY MP
interrupt controller.
- PCI/MSI:
- Prevent a use after free when PCI/MSI interrupts are released by
destroying the sysfs entries before freeing the memory which is
accessed in the sysfs show() function.
- Implement a mask quirk for the Nvidia ION AHCI chip which does not
advertise masking capability despite implementing it. Even worse the
chip comes out of reset with all MSI entries masked, which due to the
missing masking capability never get unmasked.
- Move the check which prevents accessing the MSI[X] masking for XEN
back into the low level accessors. The recent consolidation missed
that these accessors can be invoked from places which do not have
that check which broke XEN. Move them back to he original place
instead of sprinkling tons of these checks all over the code.
-----BEGIN PGP SIGNATURE-----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=LBQL
-----END PGP SIGNATURE-----
Merge tag 'irq-urgent-2021-11-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A set of fixes for the interrupt subsystem
Core code:
- A regression fix for the Open Firmware interrupt mapping code where
a interrupt controller property in a node caused a map property in
the same node to be ignored.
Interrupt chip drivers:
- Workaround a limitation in SiFive PLIC interrupt chip which
silently ignores an EOI when the interrupt line is masked.
- Provide the missing mask/unmask implementation for the CSKY MP
interrupt controller.
PCI/MSI:
- Prevent a use after free when PCI/MSI interrupts are released by
destroying the sysfs entries before freeing the memory which is
accessed in the sysfs show() function.
- Implement a mask quirk for the Nvidia ION AHCI chip which does not
advertise masking capability despite implementing it. Even worse
the chip comes out of reset with all MSI entries masked, which due
to the missing masking capability never get unmasked.
- Move the check which prevents accessing the MSI[X] masking for XEN
back into the low level accessors. The recent consolidation missed
that these accessors can be invoked from places which do not have
that check which broke XEN. Move them back to he original place
instead of sprinkling tons of these checks all over the code"
* tag 'irq-urgent-2021-11-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
of/irq: Don't ignore interrupt-controller when interrupt-map failed
irqchip/sifive-plic: Fixup EOI failed when masked
irqchip/csky-mpintc: Fixup mask/unmask implementation
PCI/MSI: Destroy sysfs before freeing entries
PCI: Add MSI masking quirk for Nvidia ION AHCI
PCI/MSI: Deal with devices lying about their MSI mask capability
PCI/MSI: Move non-mask check back into low level accessors
by placing explicit signature bytes after the call trampoline to prevent
patching random other jumps like the CFI jump table entries.
-----BEGIN PGP SIGNATURE-----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=dgiF
-----END PGP SIGNATURE-----
Merge tag 'locking-urgent-2021-11-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 static call update from Thomas Gleixner:
"A single fix for static calls to make the trampoline patching more
robust by placing explicit signature bytes after the call trampoline
to prevent patching random other jumps like the CFI jump table
entries"
* tag 'locking-urgent-2021-11-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
static_call,x86: Robustify trampoline patching
the preemption model
- clear cluster CPU masks too, on the CPU unplug path
- prevent use-after-free in cfs
- Prevent a race condition when updating CPU cache domains
- Factor out common shared part of smp_prepare_cpus() into a common
helper which can be called by both baremetal and Xen, in order to fix a
booting of Xen PV guests
-----BEGIN PGP SIGNATURE-----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=s2MX
-----END PGP SIGNATURE-----
Merge tag 'sched_urgent_for_v5.16_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Borislav Petkov:
- Avoid touching ~100 config files in order to be able to select the
preemption model
- clear cluster CPU masks too, on the CPU unplug path
- prevent use-after-free in cfs
- Prevent a race condition when updating CPU cache domains
- Factor out common shared part of smp_prepare_cpus() into a common
helper which can be called by both baremetal and Xen, in order to fix
a booting of Xen PV guests
* tag 'sched_urgent_for_v5.16_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
preempt: Restore preemption model selection configs
arch_topology: Fix missing clear cluster_cpumask in remove_cpu_topology()
sched/fair: Prevent dead task groups from regaining cfs_rq's
sched/core: Mitigate race cpus_share_cache()/update_top_cache_domain()
x86/smp: Factor out parts of native_smp_prepare_cpus()
reference to a PMU samples page has been acquired properly before that
- Make sure the LBR_SELECT MSR is saved/restored too
- Reset the LBR_SELECT MSR when resetting the LBR PMU to clear any
residual data left
-----BEGIN PGP SIGNATURE-----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=Ciqw
-----END PGP SIGNATURE-----
Merge tag 'perf_urgent_for_v5.16_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Borislav Petkov:
- Prevent unintentional page sharing by checking whether a page
reference to a PMU samples page has been acquired properly before
that
- Make sure the LBR_SELECT MSR is saved/restored too
- Reset the LBR_SELECT MSR when resetting the LBR PMU to clear any
residual data left
* tag 'perf_urgent_for_v5.16_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Avoid put_page() when GUP fails
perf/x86/vlbr: Add c->flags to vlbr event constraints
perf/x86/lbr: Reset LBR_SELECT during vlbr reset
- Do not log spurious corrected MCEs on SKL too, due to an erratum
- Clarify the path of paravirt ops patches upstream
- Add an optimization to avoid writing out AMX components to sigframes
when former are in init state
-----BEGIN PGP SIGNATURE-----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=Ge2T
-----END PGP SIGNATURE-----
Merge tag 'x86_urgent_for_v5.16_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Add the model number of a new, Raptor Lake CPU, to intel-family.h
- Do not log spurious corrected MCEs on SKL too, due to an erratum
- Clarify the path of paravirt ops patches upstream
- Add an optimization to avoid writing out AMX components to sigframes
when former are in init state
* tag 'x86_urgent_for_v5.16_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Add Raptor Lake to Intel family
x86/mce: Add errata workaround for Skylake SKX37
MAINTAINERS: Add some information to PARAVIRT_OPS entry
x86/fpu: Optimize out sigframe xfeatures when in init state
Hardware tracing:
ARM:
- Print the size of the buffer size consistently in hexadecimal in ARM Coresight.
- Add Coresight snapshot mode support.
- Update --switch-events docs in 'perf record'.
- Support hardware-based PID tracing.
- Track task context switch for cpu-mode events.
Vendor events:
- Add metric events JSON file for power10 platform
perf test:
- Get 'perf test' unit tests closer to kunit.
- Topology tests improvements.
- Remove bashisms from some tests.
perf bench:
- Fix memory leak of perf_cpu_map__new() in the futex benchmarks.
libbpf:
- Add some more weak libbpf functions o allow building with the libbpf versions, old ones,
present in distros.
libbeauty:
- Translate [gs]setsockopt 'level' argument integer values to strings.
tools headers UAPI:
- Sync futex_waitv, arch prctl, sound, i195_drm and msr-index files with the kernel sources.
Documentation:
- Add documentation to 'struct symbol'.
- Synchronize the definition of enum perf_hw_id with code in tools/perf/design.txt.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCYZAxDwAKCRCyPKLppCJ+
J6mlAQD9Oz+atprlAikeneljy3xTquBcHl0Wg2Ta6shR5JjuogEA4hPQXUDFz6/4
C1tsmSDp/UOYFumkX1VW8KOi1TAMCQ4=
=Ib8h
-----END PGP SIGNATURE-----
Merge tag 'perf-tools-for-v5.16-2021-11-13' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull more perf tools updates from Arnaldo Carvalho de Melo:
"Hardware tracing:
- ARM:
* Print the size of the buffer size consistently in hexadecimal in
ARM Coresight.
* Add Coresight snapshot mode support.
* Update --switch-events docs in 'perf record'.
* Support hardware-based PID tracing.
* Track task context switch for cpu-mode events.
- Vendor events:
* Add metric events JSON file for power10 platform
perf test:
- Get 'perf test' unit tests closer to kunit.
- Topology tests improvements.
- Remove bashisms from some tests.
perf bench:
- Fix memory leak of perf_cpu_map__new() in the futex benchmarks.
libbpf:
- Add some more weak libbpf functions o allow building with the
libbpf versions, old ones, present in distros.
libbeauty:
- Translate [gs]setsockopt 'level' argument integer values to
strings.
tools headers UAPI:
- Sync futex_waitv, arch prctl, sound, i195_drm and msr-index files
with the kernel sources.
Documentation:
- Add documentation to 'struct symbol'.
- Synchronize the definition of enum perf_hw_id with code in
tools/perf/design.txt"
* tag 'perf-tools-for-v5.16-2021-11-13' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (67 commits)
perf tests: Remove bash constructs from stat_all_pmu.sh
perf tests: Remove bash construct from record+zstd_comp_decomp.sh
perf test: Remove bash construct from stat_bpf_counters.sh test
perf bench futex: Fix memory leak of perf_cpu_map__new()
tools arch x86: Sync the msr-index.h copy with the kernel sources
tools headers UAPI: Sync drm/i915_drm.h with the kernel sources
tools headers UAPI: Sync sound/asound.h with the kernel sources
tools headers UAPI: Sync linux/prctl.h with the kernel sources
tools headers UAPI: Sync arch prctl headers with the kernel sources
perf tools: Add more weak libbpf functions
perf bpf: Avoid memory leak from perf_env__insert_btf()
perf symbols: Factor out annotation init/exit
perf symbols: Bit pack to save a byte
perf symbols: Add documentation to 'struct symbol'
tools headers UAPI: Sync files changed by new futex_waitv syscall
perf test bpf: Use ARRAY_CHECK() instead of ad-hoc equivalent, addressing array_size.cocci warning
perf arm-spe: Support hardware-based PID tracing
perf arm-spe: Save context ID in record
perf arm-spe: Update --switch-events docs in 'perf record'
perf arm-spe: Track task context switch for cpu-mode events
...
- Address an issue with the SiFive PLIC being unable to EOI
a masked interrupt
- Move the disable/enable methods in the CSky mpintc to
mask/unmask
- Fix a regression in the OF irq code where an interrupt-controller
property in the same node as an interrupt-map property would get
ignored
-----BEGIN PGP SIGNATURE-----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=27Fe
-----END PGP SIGNATURE-----
Merge tag 'irqchip-fixes-5.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent
Pull irqchip fixes from Marc Zyngier:
- Address an issue with the SiFive PLIC being unable to EOI
a masked interrupt
- Move the disable/enable methods in the CSky mpintc to
mask/unmask
- Fix a regression in the OF irq code where an interrupt-controller
property in the same node as an interrupt-map property would get
ignored
Link: https://lore.kernel.org/all/20211112173459.4015233-1-maz@kernel.org
Marco Chiappero