Commit 3ce6c9e261 ("spi: add of_device_uevent_modalias support") is
incomplete, as it didn't update the modalias_show function to generate the
of: modalias string if available.
Fixes: 3ce6c9e261 ("spi: add of_device_uevent_modalias support")
Signed-off-by: Andreas Schwab <schwab@suse.de>
Link: https://lore.kernel.org/r/mvmwnpi4fya.fsf@suse.de
Signed-off-by: Mark Brown <broonie@kernel.org>
In meson_spicc_probe, the error handling code needs to clean up master
by calling spi_master_put, but the remove function does not have this
function call. This will lead to memory leak of spicc->master.
Reported-by: Dongliang Mu <mudongliangabcd@gmail.com>
Fixes: 454fa271bc4e("spi: Add Meson SPICC driver")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20210720100116.1438974-1-mudongliangabcd@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In some cases reset_sccr1() can be called when no message available.
This means that there is no associated chip to receive that message
and hence no threshold needs to be set. Adapt the function to such
cases.
Fixes: 3bbdc08326 ("spi: pxa2xx: Reuse int_stop_and_reset() in couple of places")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210721121520.62605-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A collection of driver specific fixes, there was a bit of a kerfuffle
with some last minute review on hte spi-cadence-quadspi division by zero
change but otherwise nothing terribly remarkable here - important fixes
if you have the hardware but nothing with too wide an impact.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmD4WjwACgkQJNaLcl1U
h9CofQf/exao6MVAh2aMFv4A0UjQ4jI/wOWzhDY84ooxtTpcSlmAcPNR/yXt7yvc
2s7OcDOSRL8uO9agrnLINDzRrB/+Z8N7ra3sUwzzkNEe6YoOcLYW+GvFSYbyqqPQ
w8Ij6xn05RINQ63WuwwNHNwxlNBcXAT/bkKUkuzAinQi91hehwVQrAgoaNmbDzvI
B0NhSwVEYvlEsfvmVwOJN4VUDbFor31oE3hNvK685ATRvPEQssbQarloK4OsPajv
hOKqDNY/UKggSEFSaeN8gExrylhqEsXk1r+p0S8kKfZnyoNkemPa9xK2QD5YjulE
V9rDs90qjWoA1Rw90e61HvDbtDBgdQ==
=74y9
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A collection of driver specific fixes, there was a bit of a kerfuffle
with some last minute review on hte spi-cadence-quadspi division by
zero change but otherwise nothing terribly remarkable here - important
fixes if you have the hardware but nothing with too wide an impact"
* tag 'spi-fix-v5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-bcm2835: Fix deadlock
spi: cadence: Correct initialisation of runtime PM again
spi: cadence-quadspi: Disable Auto-HW polling
spi: spi-cadence-quadspi: Fix division by zero warning
spi: spi-cadence-quadspi: Revert "Fix division by zero warning"
spi: spi-cadence-quadspi: Fix division by zero warning
spi: mediatek: move devm_spi_register_master position
spi: mediatek: fix fifo rx mode
spi: atmel: Fix CS and initialization bug
spi: stm32: fixes pm_runtime calls in probe/remove
spi: imx: mx51-ecspi: Reinstate low-speed CONFIGREG delay
spi: stm32h7: fix full duplex irq handler handling
The driver core ignores the return value of this callback because there
is only little it can do when a device disappears.
This is the final bit of a long lasting cleanup quest where several
buses were converted to also return void from their remove callback.
Additionally some resource leaks were fixed that were caused by drivers
returning an error code in the expectation that the driver won't go
away.
With struct bus_type::remove returning void it's prevented that newly
implemented buses return an ignored error code and so don't anticipate
wrong expectations for driver authors.
Reviewed-by: Tom Rix <trix@redhat.com> (For fpga)
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com> (For drivers/s390 and drivers/vfio)
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> (For ARM, Amba and related parts)
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org> (for sunxi-rsb)
Acked-by: Pali Rohár <pali@kernel.org>
Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org> (for media)
Acked-by: Hans de Goede <hdegoede@redhat.com> (For drivers/platform)
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Juergen Gross <jgross@suse.com> (For xen)
Acked-by: Lee Jones <lee.jones@linaro.org> (For mfd)
Acked-by: Johannes Thumshirn <jth@kernel.org> (For mcb)
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> (For slimbus)
Acked-by: Kirti Wankhede <kwankhede@nvidia.com> (For vfio)
Acked-by: Maximilian Luz <luzmaximilian@gmail.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> (For ulpi and typec)
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com> (For ipack)
Acked-by: Geoff Levand <geoff@infradead.org> (For ps3)
Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com> (For thunderbolt)
Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> (For intel_th)
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net> (For pcmcia)
Acked-by: Rafael J. Wysocki <rafael@kernel.org> (For ACPI)
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> (rpmsg and apr)
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> (For intel-ish-hid)
Acked-by: Dan Williams <dan.j.williams@intel.com> (For CXL, DAX, and NVDIMM)
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com> (For isa)
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (For firewire)
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> (For hid)
Acked-by: Thorsten Scherer <t.scherer@eckelmann.de> (For siox)
Acked-by: Sven Van Asbroeck <TheSven73@gmail.com> (For anybuss)
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> (For MMC)
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Finn Thain <fthain@linux-m68k.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20210713193522.1770306-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bcm2835_spi_transfer_one function can create a deadlock
if it is called while another thread already has the
CCF lock.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Fixes: f8043872e7 ("spi: add driver for BCM2835")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210716210245.13240-2-alexandru.tachici@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The security restrictions on the FSI-attached SPI controllers have
been applied universally to all controllers, so the controller can no
longer transfer more than 8 bytes for one transfer. Refactor the driver
to remove the looping and support for larger transfers, and remove the
"restricted" compatible string, as all the controllers are now
considered restricted.
Eddie James (2):
spi: fsi: Reduce max transfer size to 8 bytes
dt-bindings: fsi: Remove ibm,fsi2spi-restricted compatible
.../devicetree/bindings/fsi/ibm,fsi2spi.yaml | 1 -
drivers/spi/spi-fsi.c | 125 +++---------------
2 files changed, 22 insertions(+), 104 deletions(-)
--
2.27.0
For each usage of fifo_words it is clear if ->dynamic_burst is true or
not. This can be used to simplify the function a bit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210716173927.2050620-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Reuse int_stop_and_reset() in couple of places.
While at it, change the order of the int_stop_and_reset() and pxa2xx_spi_off()
to be in align with the similar flow in int_error_stop().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210719074842.36060-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The original implementation of RPM handling in probe() was mostly
correct, except it failed to call pm_runtime_get_*() to activate the
hardware. The subsequent fix, 734882a8bf ("spi: cadence: Correct
initialisation of runtime PM"), breaks the implementation further,
to the point where the system using this hard IP on ZynqMP hangs on
boot, because it accesses hardware which is gated off.
Undo 734882a8bf ("spi: cadence: Correct initialisation of runtime
PM") and instead add missing pm_runtime_get_noresume() and move the
RPM disabling all the way to the end of probe(). That makes ZynqMP
not hang on boot yet again.
Fixes: 734882a8bf ("spi: cadence: Correct initialisation of runtime PM")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210716182133.218640-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
cadence-quadspi has a builtin Auto-HW polling funtionality using which
it keep tracks of completion of write operations. When Auto-HW polling
is enabled, it automatically initiates status register read operation,
until the flash clears its busy bit.
cadence-quadspi controller doesn't allow an address phase when
auto-polling the busy bit on the status register. Unlike SPI NOR
flashes, SPI NAND flashes do require the address of status register
when polling the busy bit using the read register operation. As
Auto-HW polling is enabled by default, cadence-quadspi returns a
timeout for every write operation after an indefinite amount of
polling on SPI NAND flashes.
Disable Auto-HW polling completely as the spi-nor core, spinand core,
etc. take care of polling the busy bit on their own.
Signed-off-by: Apurva Nandan <a-nandan@ti.com>
Link: https://lore.kernel.org/r/20210713125743.1540-2-a-nandan@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix below division by zero warning:
- The reason for dividing by zero is because the dummy bus width is zero,
but if the dummy n bytes is zero, it indicates that there is no data transfer,
so we can just return zero without doing any calculations.
[ 0.795337] Division by zero in kernel.
:
[ 0.834051] [<807fd40c>] (__div0) from [<804e1acc>] (Ldiv0+0x8/0x10)
[ 0.839097] [<805f0710>] (cqspi_exec_mem_op) from [<805edb4c>] (spi_mem_exec_op+0x3b0/0x3f8)
Fixes: 7512eaf541 ("spi: cadence-quadspi: Fix dummy cycle calculation when buswidth > 1")
Signed-off-by: Yoshitaka Ikeda <ikeda@nskint.co.jp>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/92eea403-9b21-2488-9cc1-664bee760c5e@nskint.co.jp
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix below division by zero warning:
- Added an if statement because buswidth can be zero, resulting in division by zero.
- The modified code was based on another driver (atmel-quadspi).
[ 0.795337] Division by zero in kernel.
:
[ 0.834051] [<807fd40c>] (__div0) from [<804e1acc>] (Ldiv0+0x8/0x10)
[ 0.839097] [<805f0710>] (cqspi_exec_mem_op) from [<805edb4c>] (spi_mem_exec_op+0x3b0/0x3f8)
Fixes: 7512eaf541 ("spi: cadence-quadspi: Fix dummy cycle calculation when buswidth > 1")
Signed-off-by: Yoshitaka Ikeda <ikeda@nskint.co.jp>
Link: https://lore.kernel.org/r/ed989af6-da88-4e0b-9ed8-126db6cad2e4@nskint.co.jp
Signed-off-by: Mark Brown <broonie@kernel.org>
The comment in setup_fifo_xfer() about setting the watermark wasn't
quite proper grammar and also stopped making sense around commit
6d66507d9b ("spi: spi-geni-qcom: Don't wait to start 1st transfer if
transmitting"). After that commit we actually start the transfer
_before_ the watermark interrupt comes.
I don't think the comment really has any value anymore. We've already
got a comment when we grab the spinlock saying that our interrupt can
come any time as a result of the things in the locked section. Let's
just remove it.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210712085010.1.Ie3bb9f9d30d6475bb75251d32635194c1c72b9ee@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch support tick_delay setting, some users need use
high-speed spi speed, which can use tick_delay to tuning spi clk timing.
Signed-off-by: Mason Zhang <Mason.Zhang@mediatek.com>
Link: https://lore.kernel.org/r/20210713114048.29509-1-mason.zhang@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch move devm_spi_register_master to the end of mtk_spi_probe.
If slaves call spi_sync in there probe function, master should have probe done.
Signed-off-by: Mason Zhang <Mason.Zhang@mediatek.com>
Link: https://lore.kernel.org/r/20210713114247.1536-1-mason.zhang@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This series contains fixes & cleanup mainly regarding fifo
and the way end of transfer triggered, when used with or
without DMA.
An additional patch cleans up the pm_runtime calls and another
one enables the autosuspend.
v2: - split pm_runtime fix patch into two
- correct revert commit subject line
Alain Volmat (6):
spi: stm32: fixes pm_runtime calls in probe/remove
spi: stm32: enable pm_runtime autosuspend
spi: stm32h7: fix full duplex irq handler handling
spi: stm32: Revert "properly handle 0 byte transfer"
spi: stm32h7: don't wait for EOT and flush fifo on disable
spi: stm32: finalize message either on dma callback or EOT
Amelie Delaunay (1):
spi: stm32h7: rework rx fifo read function
drivers/spi/spi-stm32.c | 146 +++++++++++++++++-----------------------
1 file changed, 61 insertions(+), 85 deletions(-)
--
2.25.1
This patch add no_need_unprepare support for spi, if spi src clk is
MAIN PLL, it can keep the clk_prepare and will not cause low power
issue. So we no need do clk_prepare/clk_unprepare in runtime pm,
and it will get better performance, because clk_prepare has called
mutex lock.
In the same way,
clk_get_rate also has called mutex lock, so we moved it to spi_probe.
Signed-off-by: Mason Zhang <Mason.Zhang@mediatek.com>
Link: https://lore.kernel.org/r/20210629100814.21402-1-mason.zhang@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Depending on the usage, it is necessary to perform the finalize
message operation either upon receiving the EOT interruption,
eiher upon receiving the DMA callback. Indeed, when relying
on DMA, even if the SPI EOT IT has been received, it is
necessary to wait for the end of the DMA RX transaction before
accessing to the data.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://lore.kernel.org/r/1625646426-5826-8-git-send-email-alain.volmat@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In nominal cases, disable is called as part of the unprepare_message,
after receiving a EOT and after receiving all data so it doesn't
make sense to check for EOT and empty the FIFO.
Moreover, at the end of the disable, the SPI is disable (SPE) leading
to clear of all internal FIFO, leaving the IP in a known status.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://lore.kernel.org/r/1625646426-5826-7-git-send-email-alain.volmat@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove flush parameter and check RXWNE or RXPLVL when end of transfer
flag is set.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://lore.kernel.org/r/1625646426-5826-6-git-send-email-alain.volmat@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
0 byte transfer handling is now done within the core in code added
by commit b306320322 ("spi: Skip zero-length transfers in spi_transfer_one_message()")
This reverts commit 2269f5a8b1 ("spi: stm32: properly handle 0 byte transfer")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://lore.kernel.org/r/1625646426-5826-5-git-send-email-alain.volmat@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In FIFO mode were two problems:
- RX mode was never handled and
- in this case the tx_buf pointer was NULL and caused an exception
fix this by handling RX mode in mtk_spi_fifo_transfer
Fixes: a568231f46 ("spi: mediatek: Add spi bus for Mediatek MT8173")
Signed-off-by: Peter Hess <peter.hess@ph-home.de>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20210706121609.680534-1-linux@fw-web.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 5fa5e6dec7 ("spi: atmel: Switch to transfer_one transfer
method") switched to using transfer_one and set_cs. The
core doesn't call set_cs when the chip select lines are gpios. Add the
SPI_MASTER_GPIO_SS flag to the driver to ensure the calls to set_cs
happen since the driver programs configuration registers there.
Fixes: 5fa5e6dec7 ("spi: atmel: Switch to transfer_one transfer method")
Signed-off-by: Dan Sneddon <dan.sneddon@microchip.com>
Link: https://lore.kernel.org/r/20210629192218.32125-1-dan.sneddon@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add pm_runtime calls in probe/probe error path and remove
in order to be consistent in all places in ordering and
ensure that pm_runtime is disabled prior to resources used
by the SPI controller.
This patch also fixes the 2 following warnings on driver remove:
WARNING: CPU: 0 PID: 743 at drivers/clk/clk.c:594 clk_core_disable_lock+0x18/0x24
WARNING: CPU: 0 PID: 743 at drivers/clk/clk.c:476 clk_unprepare+0x24/0x2c
Fixes: 038ac869c9 ("spi: stm32: add runtime PM support")
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Link: https://lore.kernel.org/r/1625646426-5826-2-git-send-email-alain.volmat@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since 00b80ac935 ("spi: imx: mx51-ecspi: Move some initialisation to
prepare_message hook."), the MX51_ECSPI_CONFIG write no longer happens
in prepare_transfer hook, but rather in prepare_message hook, however
the MX51_ECSPI_CONFIG delay is still left in prepare_transfer hook and
thus has no effect. This leads to low bus frequency operation problems
described in 6fd8b8503a ("spi: spi-imx: Fix out-of-order CS/SCLK
operation at low speeds") again.
Move the MX51_ECSPI_CONFIG write delay into the prepare_message hook
as well, thus reinstating the low bus frequency fix.
Fixes: 00b80ac935 ("spi: imx: mx51-ecspi: Move some initialisation to prepare_message hook.")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210703022300.296114-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of Full-Duplex mode, DXP flag is set when RXP and TXP flags are
set. But to avoid 2 different handlings, just add TXP and RXP flag in
the mask instead of DXP, and then keep the initial handling of TXP and
RXP events.
Also rephrase comment about EOTIE which is one of the interrupt enable
bits. It is not triggered by any event.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/1625042723-661-3-git-send-email-alain.volmat@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some controllers like qcom geni need the parent device to be used for
dma mapping, so add a dma_map_dev field and let drivers fill this to be
used as mapping device
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210625052213.32260-4-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
There is an assignment of ancillary->mode to itself which looks
dubious since the proceeding comment states that the speed and
mode is taken over from the SPI main device, indicating that
ancillary->mode should assigned using the value spi->mode.
Fix this.
Addresses-Coverity: ("Self assignment")
Fixes: 0c79378c01 ("spi: add ancillary device support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210623172300.161484-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Changes in v10:
- The internal CS inactive function is only supported after VER 0x00110002
Changes in v9:
- Conver to use CS GPIO description
Changes in v8:
- There is a problem with the version 7 mail format. resend it
Changes in v7:
- Fall back "rockchip,rv1126-spi" to "rockchip,rk3066-spi"
Changes in v6:
- Consider to compatibility, the "rockchip,rk3568-spi" is removed in
Series-changes v5, so the commit massage should also remove the
corresponding information
Changes in v5:
- Change to leave one compatible id rv1126, and rk3568 is compatible
with rv1126
Changes in v4:
- Adjust the order patches
- Simply commit massage like redundancy "application" content
Changes in v3:
- Fix compile error which is find by Sascha in [v2,2/8]
Jon Lin (6):
dt-bindings: spi: spi-rockchip: add description for rv1126
spi: rockchip: add compatible string for rv1126
spi: rockchip: Set rx_fifo interrupt waterline base on transfer item
spi: rockchip: Wait for STB status in slave mode tx_xfer
spi: rockchip: Support cs-gpio
spi: rockchip: Support SPI_CS_HIGH
.../devicetree/bindings/spi/spi-rockchip.yaml | 1 +
drivers/spi/spi-rockchip.c | 55 ++++++++++++++-----
2 files changed, 41 insertions(+), 15 deletions(-)
--
2.17.1
dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210623095843.3228-3-wsa+renesas@sang-engineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210623095843.3228-2-wsa+renesas@sang-engineering.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The current sun6i SPI implementation initializes the transfer too early,
resulting in SCK going high before the transfer. When using an additional
(gpio) chipselect with sun6i, the chipselect is asserted at a time when
clock is high, making the SPI transfer fail.
This is due to SUN6I_GBL_CTL_BUS_ENABLE being written into
SUN6I_GBL_CTL_REG at an early stage. Moving that to the transfer
function, hence, right before the transfer starts, mitigates that
problem.
Fixes: 3558fe900e (spi: sunxi: Add Allwinner A31 SPI controller driver)
Signed-off-by: Mirko Vogt <mirko-dev|linux@nanl.de>
Signed-off-by: Ralf Schlatterbeck <rsc@runtux.com>
Link: https://lore.kernel.org/r/20210614144507.y3udezjfbko7eavv@runtux.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Introduce support for ancillary devices, similar to existing
implementation for I2C. This is useful for devices having
multiple chip-selects, for example some microcontrollers
provide a normal SPI interface and a flashing SPI interface.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20210621175359.126729-2-sebastian.reichel@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add OF support as already done for ACPI to take driver
MODULE_DEVICE_TABLE(of, ..) into account.
For example with this change a spi nor device MODALIAS changes from:
MODALIAS=spi:spi-nor
to
MODALIAS=of:Nspi-flashT(null)Cjedec,spi-nor
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20210525091003.18228-1-m.felsch@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
In meson_spifc_probe function, when enable the device pclk clock is
error, it should use clk_disable_unprepare to release the core clock.
Signed-off-by: zpershuai <zpershuai@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/1623562172-22056-1-git-send-email-zpershuai@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following make W=1 warning:
drivers/spi/spi-mem.c:819: warning: expecting prototype for spi_mem_driver_unregister_with_owner(). Prototype was for spi_mem_driver_unregister() instead
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210601120721.3198488-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the register operation after the clock enable, otherwise system
will stuck when this driver probe.
Fixes: 71d80563b0 ("spi: spi-nxp-fspi: fix fspi panic by unexpected interrupts")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/1623317073-25158-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
No one seems to be using this global and exported function, so remove it
as it is no longer needed.
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210609071918.2852069-1-gregkh@linuxfoundation.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 4782c0a5dd ("clk: tegra: Don't deassert reset on enabling
clocks") removed some legacy code for handling resets on Tegra from
within the Tegra clock code. This exposed an issue in the Tegra20 slink
driver where the SPI controller reset was not being deasserted as needed
during probe. This is causing the Tegra30 Cardhu platform to hang on
boot. Fix this by ensuring the SPI controller reset is deasserted during
probe.
Fixes: 4782c0a5dd ("clk: tegra: Don't deassert reset on enabling clocks")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20210608071518.93037-1-jonathanh@nvidia.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch uses debugfs_regset32 interface to create the registers dump
file. Use it instead of creating a generic debugfs file with manually
written read callback function.
With these entries, users can check all the SPI controller registers
during run time.
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1622789718-13977-1-git-send-email-f.fangjian@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following compilation warning using W=1 build:
arm-linux-gnueabi-ld: drivers/spi/spi-stm32-qspi.o: in function `stm32_qspi_poll_status':
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20210604075009.25914-1-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Patrice Chotard <patrice.chotard@foss.st.com>:
From: Patrice Chotard <patrice.chotard@foss.st.com>
This series adds support for the spi_mem_poll_status() spinand
interface.
Some QSPI controllers allows to poll automatically memory
status during operations (erase, read or write). This allows to
offload the CPU for this task.
STM32 QSPI is supporting this feature, driver update are also
part of this series.
Changes in v5:
- Update spi_mem_read_status() description.
- Update poll_status() description API by indicating that data buffer is
filled with last status value.
- Update timeout parameter by timeout_ms in spi_mem_poll_status() prototype.
- Remove parenthesys arount -EINVAL in spi_mem_poll_status().
- Add missing spi_mem_supports_op() call in stm32_qspi_poll_status().
- Add Boris Reviewed-by for patch 1 and 2.
Changes in v4:
- Remove init_completion() from spi_mem_probe() added in v2.
- Add missing static for spi_mem_read_status().
- Check if operation in spi_mem_poll_status() is a READ.
- Update patch 2 commit message.
- Add comment which explains how delays has been calculated.
- Rename SPINAND_STATUS_TIMEOUT_MS to SPINAND_WAITRDY_TIMEOUT_MS.
Chnages in v3:
- Add spi_mem_read_status() which allows to read 8 or 16 bits status.
- Add initial_delay_us and polling_delay_us parameters to spi_mem_poll_status().
and also to poll_status() callback.
- Move spi_mem_supports_op() in SW-based polling case.
- Add delay before invoquing read_poll_timeout().
- Remove the reinit/wait_for_completion() added in v2.
- Add initial_delay_us and polling_delay_us parameters to spinand_wait().
- Add SPINAND_READ/WRITE/ERASE/RESET_INITIAL_DELAY_US and
SPINAND_READ/WRITE/ERASE/RESET_POLL_DELAY_US defines.
- Remove spi_mem_finalize_op() API added in v2.
Changes in v2:
- Indicates the spi_mem_poll_status() timeout unit
- Use 2-byte wide status register
- Add spi_mem_supports_op() call in spi_mem_poll_status()
- Add completion management in spi_mem_poll_status()
- Add offload/non-offload case management in spi_mem_poll_status()
- Optimize the non-offload case by using read_poll_timeout()
- mask and match stm32_qspi_poll_status()'s parameters are 2-byte wide
- Make usage of new spi_mem_finalize_op() API in
stm32_qspi_wait_poll_status()
Patrice Chotard (3):
spi: spi-mem: add automatic poll status functions
mtd: spinand: use the spi-mem poll status APIs
spi: stm32-qspi: add automatic poll status feature
drivers/mtd/nand/spi/core.c | 45 +++++++++++++------
drivers/spi/spi-mem.c | 86 ++++++++++++++++++++++++++++++++++++
drivers/spi/spi-stm32-qspi.c | 86 ++++++++++++++++++++++++++++++++----
include/linux/mtd/spinand.h | 22 +++++++++
include/linux/spi/spi-mem.h | 16 +++++++
5 files changed, 234 insertions(+), 21 deletions(-)
base-commit: 6efb943b86
--
2.17.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
The current implementation of the driver holds a spin lock for the
duration of the transfer, releasing it only to enable interrupts for
short periods of time. As this would prevent any interrupt from
happening, this could cause system performance issues every time a SPI
message is sent. Since the spi core now handles message syncronization
we can reduce the amount of time the spin-lock is held to the regions
where both the calling thread and the interrupt might interract.
Signed-off-by: Dan Sneddon <dan.sneddon@microchip.com>
Link: https://lore.kernel.org/r/20210602160816.4890-2-dan.sneddon@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
STM32 QSPI is able to automatically poll a specified register inside the
memory and relieve the CPU from this task.
As example, when erasing a large memory area, we got cpu load
equal to 50%. This patch allows to perform the same operation
with a cpu load around 2%.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20210518162754.15940-4-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With STM32 QSPI, it is possible to poll the status register of the device.
This could be done to offload the CPU during an operation (erase or
program a SPI NAND for example).
spi_mem_poll_status API has been added to handle this feature.
This new function take care of the offload/non-offload cases.
For the non-offload case, use read_poll_timeout() to poll the status in
order to release CPU during this phase.
For example, previously, when erasing large area, in non-offload case,
CPU load can reach ~50%, now it decrease to ~35%.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/r/20210518162754.15940-2-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In U-boot side, an issue has been encountered when QSPI source clock is
running at low frequency (24 MHz for example), waiting for TCF bit to be
set didn't ensure that all data has been send out the FIFO, we should also
wait that BUSY bit is cleared.
To prevent similar issue in kernel driver, we implement similar behavior
by always waiting BUSY bit to be cleared.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20210603073421.8441-1-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit 571e31fa60 ("spi: bcm2835: Cache CS register value for
->prepare_message()"), the number of slaves has been limited by a
compile-time constant. This was necessitated by statically-sized
arrays in the driver private data which contain per-slave register
values.
As suggested by Mark, move those register values to a per-slave
controller_state which is allocated on ->setup and freed on ->cleanup.
The limitation on the number of slaves is thus lifted.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Joe Burmeister <joe.burmeister@devtank.co.uk>
Cc: Phil Elwell <phil@raspberrypi.com>
Link: https://lore.kernel.org/r/a847c01f09400801e74e0630bf5a0197591554da.1622150204.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
In zynq_qspi_probe function, when enable the device clock is done,
the return of all the functions should goto the clk_dis_all label.
If num_cs is not right then this should return a negative error
code but currently it returns success.
Signed-off-by: zpershuai <zpershuai@gmail.com>
Link: https://lore.kernel.org/r/1622110857-21812-1-git-send-email-zpershuai@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit c7299fea67 ("spi: Fix spi device unregister flow") changed the
SPI core's behavior if the ->setup() hook returns an error upon adding
an spi_device: Before, the ->cleanup() hook was invoked to free any
allocations that were made by ->setup(). With the commit, that's no
longer the case, so the ->setup() hook is expected to free the
allocations itself.
I've identified 5 drivers which depend on the old behavior and am fixing
them up hereinafter: spi-bitbang.c spi-fsl-spi.c spi-omap-uwire.c
spi-omap2-mcspi.c spi-pxa2xx.c
Importantly, ->setup() is not only invoked on spi_device *addition*:
It may subsequently be called to *change* SPI parameters. If changing
these SPI parameters fails, freeing memory allocations would be wrong.
That should only be done if the spi_device is finally destroyed.
I am therefore using a bool "initial_setup" in 4 of the affected drivers
to differentiate between the invocation on *adding* the spi_device and
any subsequent invocations: spi-bitbang.c spi-fsl-spi.c spi-omap-uwire.c
spi-omap2-mcspi.c
In spi-pxa2xx.c, it seems the ->setup() hook can only fail on spi_device
addition, not any subsequent calls. It therefore doesn't need the bool.
It's worth noting that 5 other drivers already perform a cleanup if the
->setup() hook fails. Before c7299fea67, they caused a double-free
if ->setup() failed on spi_device addition. Since the commit, they're
fine. These drivers are: spi-mpc512x-psc.c spi-pl022.c spi-s3c64xx.c
spi-st-ssc4.c spi-tegra114.c
(spi-pxa2xx.c also already performs a cleanup, but only in one of
several error paths.)
Fixes: c7299fea67 ("spi: Fix spi device unregister flow")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Saravana Kannan <saravanak@google.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # pxa2xx
Link: https://lore.kernel.org/r/f76a0599469f265b69c371538794101fa37b5536.1622149321.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
It is helpful to see what state of CS signal was during one
or another SPI operation. All the same for SPI setup.
Enable tracing of the SPI setup and CS selection.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Message-Id: <20210526195655.75691-1-andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All chipsets from AR7100 up to QCA9563 have three dedicated chipselect
lines for the integrated SPI controller. Set the number of chipselect
lines available on the controller to this value.
Signed-off-by: David Bauer <mail@david-bauer.net>
Link: https://lore.kernel.org/r/20210522074453.39299-2-mail@david-bauer.net
Signed-off-by: Mark Brown <broonie@kernel.org>
The ath79 platform has been converted to pure OF. The platform data is
not needed anymore because of this.
Signed-off-by: David Bauer <mail@david-bauer.net>
Link: https://lore.kernel.org/r/20210522074453.39299-1-mail@david-bauer.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 571e31fa60 ("spi: bcm2835: Cache CS register value for
->prepare_message()") limited the number of slaves to 3 at compile-time.
The limitation was necessitated by a statically-sized array prepare_cs[]
in the driver private data which contains a per-slave register value.
The commit sought to enforce the limitation at run-time by setting the
controller's num_chipselect to 3: Slaves with a higher chipselect are
rejected by spi_add_device().
However the commit neglected that num_chipselect only limits the number
of *native* chipselects. If GPIO chipselects are specified in the
device tree for more than 3 slaves, num_chipselect is silently raised by
of_spi_get_gpio_numbers() and the result are out-of-bounds accesses to
the statically-sized array prepare_cs[].
As a bandaid fix which is backportable to stable, raise the number of
allowed slaves to 24 (which "ought to be enough for anybody"), enforce
the limitation on slave ->setup and revert num_chipselect to 3 (which is
the number of native chipselects supported by the controller).
An upcoming for-next commit will allow an arbitrary number of slaves.
Fixes: 571e31fa60 ("spi: bcm2835: Cache CS register value for ->prepare_message()")
Reported-by: Joe Burmeister <joe.burmeister@devtank.co.uk>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v5.4+
Cc: Phil Elwell <phil@raspberrypi.com>
Link: https://lore.kernel.org/r/75854affc1923309fde05e47494263bde73e5592.1621703210.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow SPI peripherals attached to this controller to know what is the
maximum transfer size and message size, so they can limit their transfer
lengths properly in case they are otherwise capable of larger transfer
sizes. For the sc18is602, this is 200 bytes in both cases, since as far
as I understand, it isn't possible to tell the controller to keep the
chip select asserted after the STOP command is sent.
The controller can support SPI messages larger than 200 bytes if
cs_change is set for individual transfers such that the portions with
chip select asserted are never longer than 200 bytes. What is not
supported is just SPI messages with a continuous chip select larger than
200. I don't think it is possible to express this using the current API,
so drivers which do send SPI messages with cs_change can safely just
look at the max_transfer_size limit.
An example of user for this is sja1105_xfer() in
drivers/net/dsa/sja1105/sja1105_spi.c which sends by default 64 * 4 =
256 byte transfers.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20210520131238.2903024-3-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For each spi_message, the sc18is602 I2C-to-SPI bridge driver checks the
length of each spi_transfer against 200 (the size of the chip's internal
buffer) minus hw->tlen (the number of bytes transferred so far).
The first byte of the transferred data is the Function ID (the SPI
slave's chip select) and as per the documentation of the chip:
https://www.nxp.com/docs/en/data-sheet/SC18IS602B.pdf
the data buffer is up to 200 bytes deep _without_ accounting for the
Function ID byte.
However, in sc18is602_txrx(), the driver keeps the Function ID as part
of the buffer, and increments hw->tlen from 0 to 1. Combined with the
check in sc18is602_check_transfer, this prevents us from issuing a
transfer that has exactly 200 bytes in size, but only 199.
Adjust the check function to reflect that the Function ID is not part of
the 200 byte deep data buffer.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20210520131238.2903024-2-olteanv@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix missing parenthesis of sizeof reported by checkpatch.pl:
WARNING: sizeof *pp should be sizeof(*pp).
The kernel coding style suggests thinking of sizeof as a function
and add parenthesis.
Signed-off-by: Zhiqi Song <songzhiqi1@huawei.com>
Link: https://lore.kernel.org/r/1621301902-64158-8-git-send-email-songzhiqi1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix missing parenthesis of sizeof reported by checkpatch.pl:
WARNING: sizeof *pp should be sizeof(*pp).
The kernel coding style suggests thinking of sizeof as a function
and add parenthesis.
Signed-off-by: Zhiqi Song <songzhiqi1@huawei.com>
Link: https://lore.kernel.org/r/1621301902-64158-7-git-send-email-songzhiqi1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix missing parenthesis of sizeof reported by checkpatch.pl:
WARNING: sizeof *pp should be sizeof(*pp).
The kernel coding style suggests thinking of sizeof as a function
and add parenthesis.
Signed-off-by: Zhiqi Song <songzhiqi1@huawei.com>
Link: https://lore.kernel.org/r/1621301902-64158-6-git-send-email-songzhiqi1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix missing parenthesis of sizeof reported by checkpatch.pl:
WARNING: sizeof *pp should be sizeof(*pp).
The kernel coding style suggests thinking of sizeof as a function
and add parenthesis.
Signed-off-by: Zhiqi Song <songzhiqi1@huawei.com>
Link: https://lore.kernel.org/r/1621301902-64158-5-git-send-email-songzhiqi1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix missing parenthesis of sizeof reported by checkpatch.pl:
WARNING: sizeof *pp should be sizeof(*pp).
The kernel coding style suggests thinking of sizeof as a function
and add parenthesis.
Signed-off-by: Zhiqi Song <songzhiqi1@huawei.com>
Link: https://lore.kernel.org/r/1621301902-64158-4-git-send-email-songzhiqi1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix missing parenthesis of sizeof reported by checkpatch.pl:
WARNING: sizeof *pp should be sizeof(*pp).
The kernel coding style suggests thinking of sizeof as a function
and add parenthesis.
Signed-off-by: Zhiqi Song <songzhiqi1@huawei.com>
Link: https://lore.kernel.org/r/1621301902-64158-3-git-send-email-songzhiqi1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix missing parenthesis of sizeof reported by checkpatch.pl:
WARNING: sizeof *pp should be sizeof(*pp).
The kernel coding style suggests thinking of sizeof as a function
and add parenthesis.
Cc: Kaiwan N Billimoria <kaiwan@designergraphix.com>
Signed-off-by: Zhiqi Song <songzhiqi1@huawei.com>
Link: https://lore.kernel.org/r/1621301902-64158-2-git-send-email-songzhiqi1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
One of the author names got an invalid char, probably due to
a bad charset conversion, being replaced by the
REPLACEMENT CHARACTER U+fffd ('�').
Use the author's e-mail has the characters without accents,
as also used at the .mailmap file.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/ff8d296e1fdcc4f1c6df94434a5720bcedcd0ecf.1621412009.git.mchehab+huawei@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The predefined mask for threshold modification can be used
in case of Intel Merrifield SPI. Replace open-coded value
with predefined mask when programming FIFO thresholds.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210517140351.901-10-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The struct chip_data had been introduced in order to keep the parameters
that may be provided on stack during device allocation. There is no need
to duplicate parameters there, which are carried on by SPI device itself.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210517140351.901-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI core may utilize properties and resources provided by the parent device.
Propagate firmware node to the child SPI controller device for that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210517140351.901-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When a spi device is unregistered and triggers a driver unbind, the
driver might need to access the spi device. So, don't have the
controller clean up the spi device before the driver is unbound. Clean
up the spi device after the driver is unbound.
Fixes: c7299fea67 ("spi: Fix spi device unregister flow")
Reported-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210505164734.175546-1-saravanak@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently GPIO CS handling, when descriptors are in use, doesn't
take into consideration that in ACPI case the default polarity
is Active High and can't be altered. Instead we have to use the
per-chip definition provided by SPISerialBus() resource.
Fixes: 766c6b63aa ("spi: fix client driver breakages when using GPIO descriptors")
Cc: Liguang Zhang <zhangliguang@linux.alibaba.com>
Cc: Jay Fang <f.fangjian@huawei.com>
Cc: Sven Van Asbroeck <thesven73@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Xin Hao <xhao@linux.alibaba.com>
Link: https://lore.kernel.org/r/20210511140912.30757-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
MODULE_DEVICE_TABLE is used to extract the device information out of the
driver and builds a table when being compiled. If using this macro,
kernel can find the driver if available when the device is plugged in,
and then loads that driver and initializes the device.
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20210512093534.243040-1-zhang.lyra@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Set of cleanups here and there related to the SPI PXA2xx driver.
On top of them, adding the special type for Intel Merrifield.
In v3:
- rebased on top of v5.13-rc1 and/or spi/for-5,14
In v2:
- cover letter (Mark)
- drop moving the header in patch 5 (Mark)
Andy Shevchenko (14):
spi: pxa2xx: Use one point of return when ->probe() fails
spi: pxa2xx: Utilize MMIO and physical base from struct ssp_device
spi: pxa2xx: Utilize struct device from struct ssp_device
spi: pxa2xx: Replace header inclusions by forward declarations
spi: pxa2xx: Unify ifdeffery used in the headers
spi: pxa2xx: Group Intel Quark specific definitions
spi: pxa2xx: Introduce int_stop_and_reset() helper
spi: pxa2xx: Reuse int_error_stop() in pxa2xx_spi_slave_abort()
spi: pxa2xx: Use pxa_ssp_enable()/pxa_ssp_disable() in the driver
spi: pxa2xx: Extract pxa2xx_spi_update() helper
spi: pxa2xx: Extract clear_SSCR1_bits() helper
spi: pxa2xx: Extract read_SSSR_bits() helper
spi: pxa2xx: Constify struct driver_data parameter
spi: pxa2xx: Introduce special type for Merrifield SPIs
drivers/spi/spi-pxa2xx-dma.c | 37 +++----
drivers/spi/spi-pxa2xx-pci.c | 4 +-
drivers/spi/spi-pxa2xx.c | 190 +++++++++++++++++----------------
drivers/spi/spi-pxa2xx.h | 52 ++++-----
include/linux/pxa2xx_ssp.h | 42 +++++++-
include/linux/spi/pxa2xx_spi.h | 9 +-
sound/soc/pxa/pxa-ssp.c | 16 ---
7 files changed, 185 insertions(+), 165 deletions(-)
--
2.30.2
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1620716922-108572-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We have a lot of hard coded values in nanoseconds or other units.
Use predefined constants to make it more clear.
While at it, add or amend comments in the corresponding functions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210510131120.49253-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel Merrifield SPI is actually more closer to PXA3xx. It has extended FIFO
(32 bytes) and additional registers to get or set FIFO thresholds.
Introduce new type for Intel Merrifield SPI host controllers and handle bigger
FIFO size.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210510124134.24638-15-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In a couple of functions the contents of struct driver_data are not altered,
hence we may constify the respective function parameter.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210510124134.24638-14-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There are few places that repeat the logic of "clear some bits in SSCR1".
Extract clear_SSCR1_bits() helper to deduplicate that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210510124134.24638-12-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
It appears that pxa2xx_spi_slave_abort()almost repeats the functionality
of the int_error_stop(). Reuse int_error_stop() in pxa2xx_spi_slave_abort().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210510124134.24638-9-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently we have three times the same few lines repeated in the code.
Deduplicate them by newly introduced int_stop_and_reset() helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210510124134.24638-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some cleanups of SPI drivers. No functional change.
Thanks,
Jay
Jay Fang (4):
spi: ppc4xx: include <linux/io.h> instead of <asm/io.h>
spi: omap-100k: Clean the value of 'status' is not used
spi: delete repeated words in comments
spi: spi-loopback-test: Fix 'tx_buf' might be 'rx_buf'
drivers/spi/spi-bcm2835aux.c | 2 +-
drivers/spi/spi-dw-mmio.c | 2 +-
drivers/spi/spi-geni-qcom.c | 4 ++--
drivers/spi/spi-loopback-test.c | 2 +-
drivers/spi/spi-omap-100k.c | 2 --
drivers/spi/spi-pl022.c | 4 ++--
drivers/spi/spi-ppc4xx.c | 4 ++--
7 files changed, 9 insertions(+), 11 deletions(-)
--
2.7.4
Set of cleanups here and there related to the SPI PXA2xx driver.
On top of them, adding the special type for Intel Merrifield.
In v2:
- cover letter (Mark)
- drop moving the header in patch 5 (Mark)
Andy Shevchenko (14):
spi: pxa2xx: Use one point of return when ->probe() fails
spi: pxa2xx: Utilize MMIO and physical base from struct ssp_device
spi: pxa2xx: Utilize struct device from struct ssp_device
spi: pxa2xx: Replace header inclusions by forward declarations
spi: pxa2xx: Unify ifdeffery used in the headers
spi: pxa2xx: Group Intel Quark specific definitions
spi: pxa2xx: Introduce int_stop_and_reset() helper
spi: pxa2xx: Reuse int_error_stop() in pxa2xx_spi_slave_abort()
spi: pxa2xx: Use pxa_ssp_enable()/pxa_ssp_disable() in the driver
spi: pxa2xx: Extract pxa2xx_spi_update() helper
spi: pxa2xx: Extract clear_SSCR1_bits() helper
spi: pxa2xx: Extract read_SSSR_bits() helper
spi: pxa2xx: Constify struct driver_data parameter
spi: pxa2xx: Introduce special type for Merrifield SPIs
drivers/spi/spi-pxa2xx-dma.c | 37 +++----
drivers/spi/spi-pxa2xx-pci.c | 4 +-
drivers/spi/spi-pxa2xx.c | 190 +++++++++++++++++----------------
drivers/spi/spi-pxa2xx.h | 52 ++++-----
include/linux/pxa2xx_ssp.h | 42 +++++++-
include/linux/spi/pxa2xx_spi.h | 9 +-
sound/soc/pxa/pxa-ssp.c | 16 ---
7 files changed, 185 insertions(+), 165 deletions(-)
--
2.30.2
pch_spi_set_tx() frees data->pkt_tx_buff on failure of kzalloc() for
data->pkt_rx_buff, but its caller, pch_spi_process_messages(), will
free data->pkt_tx_buff again. Set data->pkt_tx_buff to NULL after
kfree() to avoid double free.
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1620284888-65215-1-git-send-email-f.fangjian@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When the data structure is only referred by pointer, compiler may not need
to see the contents of the data type. Thus, we may replace header inclusions
by respective forward declarations. Due to above add missed headers as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210423182441.50272-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We have a duplication of struct device in the struct driver_data,
get rid of it and reuse member from struct ssp_device instead.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210423182441.50272-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We have a duplication of MMIO and physical base addresses in
the struct driver_data, get rid of it and reuse members from
struct ssp_device instead.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210423182441.50272-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop repeated words in spi-bcm2835aux.c
{are}
Drop repeated words in spi-dw-mmio.c
{the}
Drop repeated words in spi-geni-qcom.c
{our}
Drop repeated words in spi-pl022.c
{on}
Drop repeated words in spi-ppc4xx.c
{the}
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1620629903-15493-4-git-send-email-f.fangjian@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
An error code is set to 'status' before exiting list_for_each_entry()
loop, but the value of 'status' is not used as below:
list_for_each_entry(t, &m->transfers, transfer_list) {
if (t->tx_buf == NULL && t->rx_buf == NULL && t->len) {
status = -EINVAL;
break;
}
...
}
status = omap1_spi100k_setup_transfer(spi, NULL);
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1620629903-15493-3-git-send-email-f.fangjian@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
this patch takes the io_mutex to prevent an unprotected HW
register modification in the set_cs_timing callback.
Fixes: 4cea6b8cc3 ("spi: add power control when set_cs_timing")
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Link: https://lore.kernel.org/r/20210508060214.1485-1-leilk.liu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
'dspi_request_dma()' should be undone by a 'dspi_release_dma()' call in the
error handling path of the probe function, as already done in the remove
function
Fixes: 90ba37033c ("spi: spi-fsl-dspi: Add DMA support for Vybrid")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/d51caaac747277a1099ba8dea07acd85435b857e.1620587472.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
No surprises in this development cycle, and most of works are about
the fixes and the improvements of the existing code, while a new LED
control layer and a few new drivers have been introduced.
Here are some highlights:
Core:
- A common mute-LED framework was introduced;
used by HD-audio for now, more adaption will follow later.
The former "Mic Mute-LED Mode" mixer control has been replaced with
the corresponding sysfs now.
- User-control management was changed to count consumed bytes instead
of capping by number of elements;
this will allow more controls in the normal usage pattern while
avoiding the possible memory exhaustion DoS
ASoC:
- Continued refactoring and cleanups in ASoC core and generic card
drivers
- Wide range of small cppcheck and warning fixes
- New drivers for Freescale i.MX DMA over rpmsg, Mediatek MT6358
accessory detection, and Realtek RT1019, RT1316, RT711 and RT715
USB-audio:
- Continued improvements and fixes of the implicit feedback mode,
including better support for Pioneer and Roland/BOSS devices
HD-audio:
- Default back to non-buffer preallocation on x86
- Cirrus codec improvements, more quirks for Realtek codecs
Others:
- New virtio sound driver
- FireWire Bebob updates
Note that this PR includes a couple of changes in reset and SPI
drivers, too, and some merge conflicts might happen.
-----BEGIN PGP SIGNATURE-----
iQJCBAABCAAsFiEEIXTw5fNLNI7mMiVaLtJE4w1nLE8FAmCMJaAOHHRpd2FpQHN1
c2UuZGUACgkQLtJE4w1nLE/T6A//Ti0SAWYnAr5l/7ccuwS4zljHcuHngwvIxRPY
BokU1ZUlagi+Ro2HLUq13G8T4AlUAQ8r2ecz7EJQHHl9tkrIg7Cc0+fiBPHju1Yu
0F3Vjc78/JsJHvAR2DPll2rwhsdD3usSQXFo181k38J098X02iNcrzsj3kW5Bpzb
DBvXzOBIAg/PPfPa4edSYsSurqYeZTkhshedTohlwOCnVbW9NN5b5T9yoXP+t5na
rvK1Vhu0He8nVMBPDrzjKgE5rjm7Kn0FNXZ6CMDekU9sRVzm/PbgAqqmRnn6bUKa
GDpcQzlaiDrw8a7/uTVgUZy85F9kMXMMnfYpBy4bBXOt6RWOplXY1yMxy1RXV+op
3qC9k5R+IsjSWFQZ2z5bIHtGBNCG0698z9fQcvpsWTv+R68rUyfj+jeO/G9zzvpi
qpQTloBfI28NoP+iGis7wtrlQ15ut47YMCQS8QiOEvLmd5/3xKXRut4Ac/VmvDpS
q7fLivL8MZ/SMoXY74q/kByMBkXNpryQCAN+xAslaJ5P0aefNYJJdBt/sJlsDd9J
Ya2VIxHoP+Sb1MG6OLq1Y8c53Di9lwY80pOtF3plcz/ZWgzipirf6BhFj0OttiKP
a6+VewXA7zZcWEdw+Ik4dWP2dybWL+CuNl7Bwug8SyG9iWqg8Ph7FgoCTWAi93Fx
KKUJxsc=
=YT3U
-----END PGP SIGNATURE-----
Merge tag 'sound-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"No surprises in this development cycle, and most of work is about the
fixes and the improvements of the existing code, while a new LED
control layer and a few new drivers have been introduced.
Here are some highlights:
Core:
- A common mute-LED framework was introduced. It is used by HD-audio
for now, more adaption will follow later. The former "Mic Mute-LED
Mode" mixer control has been replaced with the corresponding sysfs
now.
- User-control management was changed to count consumed bytes instead
of capping by number of elements; this will allow more controls in
the normal usage pattern while avoiding the possible memory
exhaustion DoS
ASoC:
- Continued refactoring and cleanups in ASoC core and generic card
drivers
- Wide range of small cppcheck and warning fixes
- New drivers for Freescale i.MX DMA over rpmsg, Mediatek MT6358
accessory detection, and Realtek RT1019, RT1316, RT711 and RT715
USB-audio:
- Continued improvements and fixes of the implicit feedback mode,
including better support for Pioneer and Roland/BOSS devices
HD-audio:
- Default back to non-buffer preallocation on x86
- Cirrus codec improvements, more quirks for Realtek codecs
Others:
- New virtio sound driver
- FireWire Bebob updates"
* tag 'sound-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (587 commits)
ALSA: hda/conexant: Re-order CX5066 quirk table entries
ALSA: hda/realtek: Remove redundant entry for ALC861 Haier/Uniwill devices
ALSA: hda/realtek: Re-order ALC662 quirk table entries
ALSA: hda/realtek: Re-order remaining ALC269 quirk table entries
ALSA: hda/realtek: Re-order ALC269 Lenovo quirk table entries
ALSA: hda/realtek: Re-order ALC269 Sony quirk table entries
ALSA: hda/realtek: Re-order ALC269 ASUS quirk table entries
ALSA: hda/realtek: Re-order ALC269 Dell quirk table entries
ALSA: hda/realtek: Re-order ALC269 Acer quirk table entries
ALSA: hda/realtek: Re-order ALC269 HP quirk table entries
ALSA: hda/realtek: Re-order ALC882 Clevo quirk table entries
ALSA: hda/realtek: Re-order ALC882 Sony quirk table entries
ALSA: hda/realtek: Re-order ALC882 Acer quirk table entries
ALSA: usb-audio: Remove redundant assignment to len
ALSA: hda/realtek: Add quirk for Intel Clevo PCx0Dx
ALSA: virtio: fix kernel-doc
ALSA: hda/cirrus: Use CS8409 filter to fix abnormal sounds on Bullseye
ALSA: hda/cirrus: Set Initial DMIC volume for Bullseye to -26 dB
ALSA: sb: Fix two use after free in snd_sb_qsound_build
ALSA: emu8000: Fix a use after free in snd_emu8000_create_mixer
...
When the number of bytes for the op is greater than one, the read could
run off the end of the function stack and cause a crash.
This patch restores the behaviour of safely reading out of the original
opcode location.
Signed-off-by: Karen Dombroski <karen.dombroski@marsbioimaging.com>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20210429053802.17650-3-amit.kumar-mahapatra@xilinx.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI_ALTERA_CORE config symbol controls compilation of the Altera SPI
Controller core code. It is already selected by all of its users, so
there is no reason to make it visible, unless compile-testing.
Fixes: b0c3d9354d ("spi: altera: separate core code from platform code")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/f0cb8e66baba4506db6f42fca74dc51b76883507.1619534253.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
When an SPI device is unregistered, the spi->controller->cleanup() is
called in the device's release callback. That's wrong for a couple of
reasons:
1. spi_dev_put() can be called before spi_add_device() is called. And
it's spi_add_device() that calls spi_setup(). This will cause clean()
to get called without the spi device ever being setup.
2. There's no guarantee that the controller's driver would be present by
the time the spi device's release function gets called.
3. It also causes "sleeping in atomic context" stack dump[1] when device
link deletion code does a put_device() on the spi device.
Fix these issues by simply moving the cleanup from the device release
callback to the actual spi_unregister_device() function.
[1] - https://lore.kernel.org/lkml/CAHp75Vc=FCGcUyS0v6fnxme2YJ+qD+Y-hQDQLa2JhWNON9VmsQ@mail.gmail.com/
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20210426235638.1285530-1-saravanak@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
- Clean up list_sort prototypes (Sami Tolvanen)
- Introduce CONFIG_CFI_CLANG for arm64 (Sami Tolvanen)
-----BEGIN PGP SIGNATURE-----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=wU6U
-----END PGP SIGNATURE-----
Merge tag 'cfi-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull CFI on arm64 support from Kees Cook:
"This builds on last cycle's LTO work, and allows the arm64 kernels to
be built with Clang's Control Flow Integrity feature. This feature has
happily lived in Android kernels for almost 3 years[1], so I'm excited
to have it ready for upstream.
The wide diffstat is mainly due to the treewide fixing of mismatched
list_sort prototypes. Other things in core kernel are to address
various CFI corner cases. The largest code portion is the CFI runtime
implementation itself (which will be shared by all architectures
implementing support for CFI). The arm64 pieces are Acked by arm64
maintainers rather than coming through the arm64 tree since carrying
this tree over there was going to be awkward.
CFI support for x86 is still under development, but is pretty close.
There are a handful of corner cases on x86 that need some improvements
to Clang and objtool, but otherwise works well.
Summary:
- Clean up list_sort prototypes (Sami Tolvanen)
- Introduce CONFIG_CFI_CLANG for arm64 (Sami Tolvanen)"
* tag 'cfi-v5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
arm64: allow CONFIG_CFI_CLANG to be selected
KVM: arm64: Disable CFI for nVHE
arm64: ftrace: use function_nocfi for ftrace_call
arm64: add __nocfi to __apply_alternatives
arm64: add __nocfi to functions that jump to a physical address
arm64: use function_nocfi with __pa_symbol
arm64: implement function_nocfi
psci: use function_nocfi for cpu_resume
lkdtm: use function_nocfi
treewide: Change list_sort to use const pointers
bpf: disable CFI in dispatcher functions
kallsyms: strip ThinLTO hashes from static functions
kthread: use WARN_ON_FUNCTION_MISMATCH
workqueue: use WARN_ON_FUNCTION_MISMATCH
module: ensure __cfi_check alignment
mm: add generic function_nocfi macro
cfi: add __cficanonical
add support for Clang CFI
The only core work for SPI this time around is the completion of the
conversion to the new style method for specifying transfer delays,
meaning we can cope with what most controllers support more directly
using conversions in the core rather than open coding in drivers.
Otherwise it's a good stack of cleanups and fixes plus a few new
drivers.
The conversion to new style transfer delay will cause an issue with a
newly added staging driver which has a straightforward resolution in
-next.
- Completion of the conversion to new style transfer delay
configuration.
- Introduction and use of module_parport_driver() helper, merged here
as there's no parport tree.
- Support for Altera SoCs on DFL buses, NXP i.MX8DL, HiSilicon Kunpeng,
MediaTek MT8195,
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmCG0FYACgkQJNaLcl1U
h9BXlAf/ZQaU8Nq4NY2jgjzjUoplF4qSFvCZ05CXqfYftaAOp06AmoOwNuNTz2gU
Fkxouuw3D0hNmaeVusF1PaRjIvJCu+RO68EDrzTJlcFytyC8CxWSDE4Yw6ytOBUM
OWZdVXsuw0CUk3VRJl2ycCooeTyKaCksfkVucocZAoyexcfQrFpxkOCUbA8hVM43
Hghzb8HWAZUerrfwreSwfvyVMralR3rqqbZFKgSgT/sRM3zpaR4sctIkNgKKEbFE
eRPRfBIWWZdJtjQ+uifFAc3jJHeZlmNXuQq3C+ETd2vQDFlymTxj+U3u74ieZxrm
c6V4u4R3+Qx9qONV/q0LV6E4sBSvdw==
=cBUy
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The only core work for SPI this time around is the completion of the
conversion to the new style method for specifying transfer delays,
meaning we can cope with what most controllers support more directly
using conversions in the core rather than open coding in drivers.
Otherwise it's a good stack of cleanups and fixes plus a few new
drivers.
Summary:
- Completion of the conversion to new style transfer delay
configuration
- Introduction and use of module_parport_driver() helper, merged here
as there's no parport tree
- Support for Altera SoCs on DFL buses, NXP i.MX8DL, HiSilicon
Kunpeng, MediaTek MT8195"
* tag 'spi-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (113 commits)
spi: Rename enable1 to activate in spi_set_cs()
spi: Convert Freescale QSPI binding to json schema
spi: stm32-qspi: fix debug format string
spi: tools: make a symbolic link to the header file spi.h
spi: fsi: add a missing of_node_put
spi: Make error handling of gpiod_count() call cleaner
spidev: Add Micron SPI NOR Authenta device compatible
spi: brcm,spi-bcm-qspi: convert to the json-schema
spi: altera: Add DFL bus driver for Altera API Controller
spi: altera: separate core code from platform code
spi: stm32-qspi: Fix compilation warning in ARM64
spi: Handle SPI device setup callback failure.
spi: sync up initial chipselect state
spi: stm32-qspi: Add dirmap support
spi: stm32-qspi: Trigger DMA only if more than 4 bytes to transfer
spi: stm32-qspi: fix pm_runtime usage_count counter
spi: spi-zynqmp-gqspi: return -ENOMEM if dma_map_single fails
spi: spi-zynqmp-gqspi: fix use-after-free in zynqmp_qspi_exec_op
spi: spi-zynqmp-gqspi: Resolved slab-out-of-bounds bug
spi: spi-zynqmp-gqspi: fix hang issue when suspend/resume
...
The enable1 is confusing name. Change it to clearly show what is
the intention behind it. No functional changes.
Fixes: 25093bdeb6 ("spi: implement SW control for CS times")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210420131846.75983-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Printing size_t needs a special %zx format modifier to avoid a
warning like:
drivers/spi/spi-stm32-qspi.c:481:41: note: format string is defined here
481 | dev_dbg(qspi->dev, "%s len = 0x%x offs = 0x%llx buf = 0x%p\n", __func__, len, offs, buf);
Patrice already tried to fix this, but picked %lx instead of %zx,
which fixed some architectures but broke others in the same way.
Using %zx works everywhere.
Fixes: 18674dee3c ("spi: stm32-qspi: Add dirmap support")
Fixes: 1b8a7d4282 ("spi: stm32-qspi: Fix compilation warning in ARM64")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210422134955.1988316-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Each time we call spi_get_gpio_descs() the num_chipselect is overwritten
either by new value or by the old one. This is an extra operation in case
gpiod_count() returns an error. Besides that it slashes the error handling
of gpiod_count().
Refactor the code to make error handling of gpiod_count() call cleaner.
Note, that gpiod_count() never returns 0, take this into account as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210420164040.40055-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ffz(), that has been used to count unused native CSs,
might cause undefined behaviour when called against ~0U.
To fix that, open code it with ffs(~value) - 1.
Fixes: 7d93aecdb5 ("spi: Add generic support for unused native cs with cs-gpios")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210420164425.40287-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The commit 7d93aecdb5 ("spi: Add generic support for unused native cs
with cs-gpios") excludes the valid case for the controllers that doesn't
need to switch native CS in order to perform the transfer, i.e. when
0 native
... ...
<n> - 1 native
<n> GPIO
<n> + 1 GPIO
... ...
where <n> defines maximum of native CSs supported by the controller.
To allow this, bail out from spi_get_gpio_descs() conditionally for
the controllers which explicitly marked with SPI_MASTER_GPIO_SS.
Fixes: 7d93aecdb5 ("spi: Add generic support for unused native cs with cs-gpios")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210420164425.40287-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, the SPI core doesn't set the struct device fwnode pointer
when it creates a new SPI device. This means when the device is
registered the fwnode is NULL and the check in device_add which sets
the fwnode->dev pointer is skipped. This wasn't previously an issue,
however these two patches:
commit 4731210c09 ("gpiolib: Bind gpio_device to a driver to enable
fw_devlink=on by default")
commit ced2af4195 ("gpiolib: Don't probe gpio_device if it's not the
primary device")
Added some code to the GPIO core which relies on using that
fwnode->dev pointer to determine if a driver is bound to the fwnode
and if not bind a stub GPIO driver. This means the GPIO providers
behind SPI will get both the expected driver and this stub driver
causing the stub driver to fail if it attempts to request any pin
configuration. For example on my system:
madera-pinctrl madera-pinctrl: pin gpio5 already requested by madera-pinctrl; cannot claim for gpiochip3
madera-pinctrl madera-pinctrl: pin-4 (gpiochip3) status -22
madera-pinctrl madera-pinctrl: could not request pin 4 (gpio5) from group aif1 on device madera-pinctrl
gpio_stub_drv gpiochip3: Error applying setting, reverse things back
gpio_stub_drv: probe of gpiochip3 failed with error -22
The firmware node on the device created by the GPIO framework is set
through the of_node pointer hence things generally actually work,
however that fwnode->dev is never set, as the check was skipped at
device_add time. This fix appears to match how the I2C subsystem
handles the same situation.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20210421101402.8468-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds a Device Feature List (DFL) bus driver for the
Altera SPI Master controller. The SPI master is connected to an
Intel SPI Slave to Avalon Bridge inside an Intel MAX10
BMC Chip.
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Link: https://lore.kernel.org/r/20210416165720.554144-3-matthew.gerlach@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Andreas Schwab