Just a few new device ids, omap serial driver regression fixes, and a
build fix for the 8250 driver movement.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk80KZgACgkQMUfUDdst+yk0HgCeIdU3VTWqdxZDXp3G1sFIXZ1b
47YAnRAMAar+/aLaNhqGrcz7aa5y2cUU
=8sr8
-----END PGP SIGNATURE-----
Merge tag 'tty-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Serial/TTY fixes for the 3.3-rc3 tree
Just a few new device ids, omap serial driver regression fixes, and a
build fix for the 8250 driver movement.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'tty-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: omap-serial: wakeup latency constraint is in microseconds, not milliseconds
tty: serial: OMAP: block idle while the UART is transferring data in PIO mode
tty: serial: OMAP: use a 1-byte RX FIFO threshold in PIO mode
m32r: relocate drivers back out of 8250 dir
tty: fix a build failure on sparc
serial: samsung: Add support for EXYNOS5250
serial: samsung: Add support for EXYNOS4212 and EXYNOS4412
drivers/tty/vt/vt_ioctl.c: fix KDFONTOP 32bit compatibility layer
Big things here is the deletion of the Android pmem driver, as it's
obsolete and no one uses it, the gma500 driver as it's already in the
drm portion of the kernel tree, and the pohmelfs filesystem as it's
obsolete and a rewritten version is being proposed for the fs/ section
of the kernel.
Other than that, a smattering of different bugfixes and regressions, and
some omap drm api merge fixups that were needed due to api changes in
the main portion of the drm tree, allowing this code to build properly
again.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk80KLYACgkQMUfUDdst+ykhiwCg2ctSu4umygA1ErAedAA+sJkv
psYAn20OZQDyuBcBAIzL2L+Y/BUz8bXt
=xvyx
-----END PGP SIGNATURE-----
Merge tag 'staging-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Staging tree patches for 3.3-rc3
Big things here is the deletion of the Android pmem driver, as it's
obsolete and no one uses it, the gma500 driver as it's already in the
drm portion of the kernel tree, and the pohmelfs filesystem as it's
obsolete and a rewritten version is being proposed for the fs/ section
of the kernel.
Other than that, a smattering of different bugfixes and regressions, and
some omap drm api merge fixups that were needed due to api changes in
the main portion of the drm tree, allowing this code to build properly
again.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'staging-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (28 commits)
staging: pohmelfs: remove drivers/staging/pohmelfs
staging: android/ram_console: Don't build on arches w/o ioremap
staging: r8712u: Use asynchronous firmware loading
staging: usbip: fix to prevent potentially using uninitialized spinlock
staging: r8712u: Fix problem when CONFIG_R8712_AP is set
staging: tidspbridge: fix incorrect free to drv_datap
staging: tidspbridge: fix bridge_open memory leaks
staging: android: lowmemorykiller: Don't wait more than one second for a process to die
MAINTAINERS: staging: iio: add iio information
staging: zcache: fix serialization bug in zv stats
staging: fix go7007-usb license
Staging: android: binder: Fix crashes when sharing a binder file between processes
Staging: android: Remove pmem driver
Staging: asus_oled: fix NULL-ptr crash on unloading
Staging: asus_oled: fix image processing
Staging: android: binder: Don't call dump_stack in binder_vma_open
staging: r8712u: Add new Sitecom UsB ID
zcache: Set SWIZ_BITS to 8 to reduce tmem bucket lock contention.
zcache: fix deadlock condition
staging: drm/omap: fix locking issue
...
A few fixes for kobject warnings that have popped up in the cpu hotplug path,
and a regression fix for the speed of the hotplug memory code.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk80J1cACgkQMUfUDdst+ylYfgCcClIeUw4njh3Tup9BpRrdBprr
fBsAoLKKhaZDsnma85PJRDAvtM2guoi7
=0TZ9
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Driver core fixes for the 3.3-rc3 tree.
A few fixes for kobject warnings that have popped up in the cpu hotplug path,
and a regression fix for the speed of the hotplug memory code.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'driver-core-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver-core: cpu: fix kobject warning when hotplugging a cpu
ACPI: remove duplicated lines of merging problems with acpi_processor_add
docbook: fix fatal errors in device-drivers docbook and add DMA Management section
drivers/base/memory.c: fix memory_dev_init() long delay
driver core: cpu: remove kernel warning when removing a cpu
Nothing big here, some Kconfig fixes for the MISC_DEVICES config option
that was being used incorrectly, and some other minor bug fixes.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk80HSAACgkQMUfUDdst+ymFsQCghwKbV9B9z5fgUXYwFQJ/pD2j
GhsAn3J2mhhHN/vtSPQAN9Vu59Xb/tCi
=VZaE
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Minor char-misc fixes for 3.3-rc3
Nothing big here, some Kconfig fixes for the MISC_DEVICES config option
that was being used incorrectly, and some other minor bug fixes.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'char-misc-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mmc: cb710 core: Add missing spin_lock_init for irq_lock of struct cb710_chip
cs5535-mfgpt: don't call __init function from __devinit
vmw_balloon: fix for a -Wuninitialized warning
drivers: misc: Remove MISC_DEVICES config option
c2port: fix build error for duramar2150 due to missing header.
Here are a few minor USB fixes and a bunch of device id updates for the
USB drivers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk80Ki4ACgkQMUfUDdst+ymp3wCfUG2LtQOC2qpzpnl1bcivSA18
11gAn09DbcldfH4k12HyCr7PuBnjILQh
=vfEv
-----END PGP SIGNATURE-----
Merge tag 'usb-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
USB fixes for 3.3-rc3
Here are a few minor USB fixes and a bunch of device id updates for the
USB drivers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'usb-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: usbserial: add new PID number (0xa951) to the ftdi driver
usb: ch9.h: usb_endpoint_maxp() uses __le16_to_cpu()
usb: musb: fix a build error on mips
uwb & wusb & usb wireless controllers: fix kconfig error & build errors
usb: Skip PCI USB quirk handling for Netlogic XLP
powerpc/usb: fix issue of CPU halt when missing USB PHY clock
usb: otg: mv_otg: Add dependence
usb: host: Distinguish Kconfig text for Freescale controllers
USB: add new zte 3g-dongle's pid to option.c
usb: ch9.h: usb_endpoint_maxp() uses __le16_to_cpu()
USB: qcserial: don't enable autosuspend
USB: qcserial: add several new serial devices
usb: otg: mv_otg: Add dependence
usb: gadget: zero: fix bug in loopback autoresume handling
The receive FIFO wakeup latency estimate in the omap-serial driver is
three orders of magnitude too small. This effectively prevents the
MPU from going to a low-power state when CONFIG_CPU_IDLE=y. This is a
major power management regression and masks some other FIFO-related
bugs in the driver.
Fix by correcting the most egregious problem in the RX wakeup latency
estimate. There are several other flaws in the estimator; these will
be fixed by a separate patch series intended for 3.4.
The difference in low-power states with this patch can be observed via
debugfs in pm_debug/count.
This estimate does not have any effect when CONFIG_CPU_IDLE=n.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prevent OMAP UARTs from going idle while they are still transferring
data in PIO mode. This works around an oversight in the OMAP UART
hardware present in OMAP34xx and earlier: an idle UART won't send a
wakeup when the TX FIFO threshold is reached. This causes long delays
during data transmission when the MPU powerdomain enters a low-power
mode. The MPU interrupt controller is not able to respond to
interrupts when it's in a low-power state, so the TX buffer is not
refilled until another wakeup event occurs.
This fix changes the erratum i291 DMA idle workaround. Rather than
toggling between force-idle and no-idle, it will toggle between
smart-idle and no-idle. The important part of the workaround is the
no-idle part, so this shouldn't result in any change in behavior.
This fix should work on all OMAP UARTs. Future patches intended for
the 3.4 merge window will make this workaround conditional on a
"feature" flag, and will use the OMAP36xx+ TX event wakeup support.
Thanks to Kevin Hilman <khilman@ti.com> for mentioning the erratum i291
workaround, which led to the development of this approach.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the (default) PIO mode, use a one-byte RX FIFO threshold. The OMAP
UART IP blocks do not appear to be capable of waking the system under
an RX timeout condition. Since the previous RX FIFO threshold was 16
bytes, this meant that omap-serial.c did not become aware of any
received data until all those bytes arrived or until another UART
interrupt occurred. This made the serial console and presumably other
serial applications (GPS, serial Bluetooth) unusable or extremely
slow. A 1-byte RX FIFO threshold also allows the MPU to enter a
low-power consumption state while waiting for the FIFO to fill.
This can be verified using the serial console by comparing the
behavior when "0123456789abcde" is pasted in from another window, with
the behavior when "0123456789abcdef" is pasted in. Since the former
string is less than sixteen bytes long, the string is not echoed for
some time, while the latter string is echoed immediately.
DMA operation is unaffected by this patch.
Thanks to Russell King - ARM Linux <linux@arm.linux.org.uk> for some
additional information on the standard behavior of the RX timeout
event, which was used to improve this commit description.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Govindraj Raja <govindraj.r@ti.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
_parse_integer() does one or two division instructions (which are slow)
per digit parsed to perform the overflow check.
Furthermore, these are particularly expensive examples of division
instruction as the number of clock cycles required to complete them may
go up with the position of the most significant set bit in the dividend:
if (*res > div_u64(ULLONG_MAX - val, base))
which is as maximal as possible.
Worse, on 32-bit arches, more than one of these division instructions
may be required per digit.
So, assuming we don't support a base of more than 16, skip the check if the
top nibble of the result is not set at this point.
Signed-off-by: David Howells <dhowells@redhat.com>
[ Changed it to not dereference the pointer all the time - even if the
compiler can and does optimize it away, the code just looks cleaner.
And edited the top nybble test slightly to make the code generated on
x86-64 better in the loop - test against a hoisted constant instead of
shifting and testing the result ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows altera_uart to be used for KGDB debugging over serial line.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function has no users inside the tree and the nios2
(out-of-mainline) port doesn't use it either (anymore).
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a real possibility of killing kernel threads that might
have issued use_mm(), so kthread's mm might become non-NULL.
This patch fixes the issue by checking for PF_KTHREAD (just as
get_task_mm()).
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sysrq should grab the tasklist lock, otherwise calling force_sig() is
not safe, as it might race with exiting task, which ->sighand might be
set to NULL already.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pch_uart_hal_request() has parameters which it never uses, also
it is very short, so merge it with its caller to make code cleaner.
No functional changes at all.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The short get_msr() has some unnecessary code and only used once,
so merge it with its caller to make code cleaner. No functional
change at all.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver will be use as interfaces for multiple kinds of
devices like Bluetooth/GPS etc, this debug hook will make driver
debugging much easier.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One patch fixes an bug in the ARM/MSM IOMMU code which returned sucess
in the unmap function even when an error occured and the other patch
adds a workaround into the AMD IOMMU driver to better handle broken IVRS
ACPI tables (this patch fixes the case when a device is not listed in
the table but actually translated by the iommu).
* 'iommu/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/msm: Fix error handling in msm_iommu_unmap()
iommu/amd: Work around broken IVRS tables
This series contains pending target bug-fixes and cleanups for v3.3-rc3
that have been addressed the past weeks in lio-core.git.
Some of the highlights include:
- Fix handling for control CDBs with data greater than PAGE_SIZE (andy)
- Use IP_FREEBIND for iscsi-target to address network portal creation
issues with systemd (dax)
- Allow PERSISTENT RESERVE IN for non-reservation holder (marco)
- Fix iblock se_dev_attrib.unmap_granularity (marco)
- Fix unsupported WRITE_SAME sense payload handling (martin)
- Add workaround for zero-length control CDB handling (nab)
- Fix discovery with INADDR_ANY and IN6ADDR_ANY_INIT (nab)
- Fix target_submit_cmd() exception handling (nab)
- Return correct ASC for unimplemented VPD pages (roland)
- Don't zero pages used for data buffers (roland)
- Fix return code of core_tpg_.*_lun (sebastian)
* '3.3-rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (26 commits)
target: Fix unsupported WRITE_SAME sense payload
iscsi: use IP_FREEBIND socket option
iblock: fix handling of large requests
target: handle empty string writes in sysfs
iscsi_target: in_aton needs linux/inet.h
target: Fix iblock se_dev_attrib.unmap_granularity
target: Fix target_submit_cmd() exception handling
target: Change target_submit_cmd() to return void
target: accept REQUEST_SENSE with 18bytes
target: Fail INQUIRY commands with EVPD==0 but PAGE CODE!=0
target: Return correct ASC for unimplemented VPD pages
iscsi-target: Fix discovery with INADDR_ANY and IN6ADDR_ANY_INIT
target: Allow control CDBs with data > 1 page
iscsi-target: Fix up a few assignments
iscsi-target: make one-bit bitfields unsigned
iscsi-target: Fix double list_add with iscsit_alloc_buffs reject
iscsi-target: Fix reject release handling in iscsit_free_cmd()
target: fix return code of core_tpg_.*_lun
target: use save/restore lock primitive in core_dec_lacl_count()
target: avoid multiple outputs in scsi_dump_inquiry()
...
1/ two small fixes to ensure we handle an interrupted resync properly.
2/ avoid loading the bitmap multiple times in dm-raid
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=k0Xz
-----END PGP SIGNATURE-----
Merge tag 'md-3.3-fixes' of git://neil.brown.name/md
Some simple md-related fixes.
1/ two small fixes to ensure we handle an interrupted resync properly.
2/ avoid loading the bitmap multiple times in dm-raid
* tag 'md-3.3-fixes' of git://neil.brown.name/md:
md: two small fixes to handling interrupt resync.
Prevent DM RAID from loading bitmap twice.
Minor SPI device driver changes. A rename of the pch_spi_pcidev symbol
that merely eliminates a modpost warning, and a Kconfig change to allow
the Samsung spi driver to build on EXYNOS.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=0yQc
-----END PGP SIGNATURE-----
Merge tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6
SPI bug fixes for v3.3-rc2
Minor SPI device driver changes. A rename of the pch_spi_pcidev symbol
that merely eliminates a modpost warning, and a Kconfig change to allow
the Samsung spi driver to build on EXYNOS.
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6:
spi-topcliff-pch: rename pch_spi_pcidev to pch_spi_pcidev_driver
spi: Add spi-s3c64xx driver dependency on ARCH_EXYNOS4
Five fixes
* branch 'akpm':
pcmcia: fix socket refcount decrementing on each resume
mm: fix UP THP spin_is_locked BUGs
drivers/leds/leds-lm3530.c: fix setting pltfm->als_vmax
mm: compaction: check for overlapping nodes during isolation for migration
nilfs2: avoid overflowing segment numbers in nilfs_ioctl_clean_segments()
This fixes a memory-corrupting bug: not only does it cause the warning,
but as a result of dropping the refcount to zero, it causes the
pcmcia_socket0 device structure to be freed while it still has
references, causing slab caches corruption. A fatal oops quickly
follows this warning - often even just a 'dmesg' following the warning
causes the kernel to oops.
While testing suspend/resume on an ARM device with PCMCIA support, and a
CF card inserted, I found that after five suspend and resumes, the
kernel would complain, and shortly die after with slab corruption.
WARNING: at include/linux/kref.h:41 kobject_get+0x28/0x50()
As the message doesn't give a clue about which kobject, and the built-in
debugging in drivers/base/power/main.c happens too late, this was added
right before each get_device():
printk("%s: %p [%s] %u\n", __func__, dev, kobject_name(&dev->kobj), atomic_read(&dev->kobj.kref.refcount));
and on the 3rd s2ram cycle, the following behaviour observed:
On the 3rd suspend/resume cycle:
dpm_prepare: c1a0d998 [pcmcia_socket0] 3
dpm_suspend: c1a0d998 [pcmcia_socket0] 3
dpm_suspend_noirq: c1a0d998 [pcmcia_socket0] 3
dpm_resume_noirq: c1a0d998 [pcmcia_socket0] 3
dpm_resume: c1a0d998 [pcmcia_socket0] 3
dpm_complete: c1a0d998 [pcmcia_socket0] 2
4th:
dpm_prepare: c1a0d998 [pcmcia_socket0] 2
dpm_suspend: c1a0d998 [pcmcia_socket0] 2
dpm_suspend_noirq: c1a0d998 [pcmcia_socket0] 2
dpm_resume_noirq: c1a0d998 [pcmcia_socket0] 2
dpm_resume: c1a0d998 [pcmcia_socket0] 2
dpm_complete: c1a0d998 [pcmcia_socket0] 1
5th:
dpm_prepare: c1a0d998 [pcmcia_socket0] 1
dpm_suspend: c1a0d998 [pcmcia_socket0] 1
dpm_suspend_noirq: c1a0d998 [pcmcia_socket0] 1
dpm_resume_noirq: c1a0d998 [pcmcia_socket0] 1
dpm_resume: c1a0d998 [pcmcia_socket0] 1
dpm_complete: c1a0d998 [pcmcia_socket0] 0
------------[ cut here ]------------
WARNING: at include/linux/kref.h:41 kobject_get+0x28/0x50()
Modules linked in: ucb1x00_core
Backtrace:
[<c0212090>] (dump_backtrace+0x0/0x110) from [<c04799dc>] (dump_stack+0x18/0x1c)
[<c04799c4>] (dump_stack+0x0/0x1c) from [<c021cba0>] (warn_slowpath_common+0x50/0x68)
[<c021cb50>] (warn_slowpath_common+0x0/0x68) from [<c021cbdc>] (warn_slowpath_null+0x24/0x28)
[<c021cbb8>] (warn_slowpath_null+0x0/0x28) from [<c0335374>] (kobject_get+0x28/0x50)
[<c033534c>] (kobject_get+0x0/0x50) from [<c03804f4>] (get_device+0x1c/0x24)
[<c0388c90>] (dpm_complete+0x0/0x1a0) from [<c0389cc0>] (dpm_resume_end+0x1c/0x20)
...
Looking at commit 7b24e79882 ("pcmcia: split up central event handler"),
the following change was made to cs.c:
return 0;
}
#endif
-
- send_event(skt, CS_EVENT_PM_RESUME, CS_EVENT_PRI_LOW);
+ if (!(skt->state & SOCKET_CARDBUS) && (skt->callback))
+ skt->callback->early_resume(skt);
return 0;
}
And the corresponding change in ds.c is from:
-static int ds_event(struct pcmcia_socket *skt, event_t event, int priority)
-{
- struct pcmcia_socket *s = pcmcia_get_socket(skt);
...
- switch (event) {
...
- case CS_EVENT_PM_RESUME:
- if (verify_cis_cache(skt) != 0) {
- dev_dbg(&skt->dev, "cis mismatch - different card\n");
- /* first, remove the card */
- ds_event(skt, CS_EVENT_CARD_REMOVAL, CS_EVENT_PRI_HIGH);
- mutex_lock(&s->ops_mutex);
- destroy_cis_cache(skt);
- kfree(skt->fake_cis);
- skt->fake_cis = NULL;
- s->functions = 0;
- mutex_unlock(&s->ops_mutex);
- /* now, add the new card */
- ds_event(skt, CS_EVENT_CARD_INSERTION,
- CS_EVENT_PRI_LOW);
- }
- break;
...
- }
- pcmcia_put_socket(s);
- return 0;
-} /* ds_event */
to:
+static int pcmcia_bus_early_resume(struct pcmcia_socket *skt)
+{
+ if (!verify_cis_cache(skt)) {
+ pcmcia_put_socket(skt);
+ return 0;
+ }
+ dev_dbg(&skt->dev, "cis mismatch - different card\n");
+ /* first, remove the card */
+ pcmcia_bus_remove(skt);
+ mutex_lock(&skt->ops_mutex);
+ destroy_cis_cache(skt);
+ kfree(skt->fake_cis);
+ skt->fake_cis = NULL;
+ skt->functions = 0;
+ mutex_unlock(&skt->ops_mutex);
+ /* now, add the new card */
+ pcmcia_bus_add(skt);
+ return 0;
+}
As can be seen, the original function called pcmcia_get_socket() and
pcmcia_put_socket() around the guts, whereas the replacement code
calls pcmcia_put_socket() only in one path. This creates an imbalance
in the refcounting.
Testing with pcmcia_put_socket() put removed shows that the bug is gone:
dpm_suspend: c1a10998 [pcmcia_socket0] 5
dpm_suspend_noirq: c1a10998 [pcmcia_socket0] 5
dpm_resume_noirq: c1a10998 [pcmcia_socket0] 5
dpm_resume: c1a10998 [pcmcia_socket0] 5
dpm_complete: c1a10998 [pcmcia_socket0] 5
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix CONFIG_TRANSPARENT_HUGEPAGE=y CONFIG_SMP=n CONFIG_DEBUG_VM=y
CONFIG_DEBUG_SPINLOCK=n kernel: spin_is_locked() is then always false,
and so triggers some BUGs in Transparent HugePage codepaths.
asm-generic/bug.h mentions this problem, and provides a WARN_ON_SMP(x);
but being too lazy to add VM_BUG_ON_SMP, BUG_ON_SMP, WARN_ON_SMP_ONCE,
VM_WARN_ON_SMP_ONCE, just test NR_CPUS != 1 in the existing VM_BUG_ONs.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In current code, pltfm->als_vmin is set to LM3530_ALS_WINDOW_mV and
pltfm->als_vmax is 0. This does not make sense. I think what we want
here is setting pltfm->als_vmax to LM3530_ALS_WINDOW_mV.
Both als_vmin and als_vmax local variables will be set to
pltfm->als_vmin and pltfm->als_vmax by a few lines latter. Thus also
remove a redundant assignment for als_vmin and als_vmax in this patch.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Acked-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Tested-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When isolating pages for migration, migration starts at the start of a
zone while the free scanner starts at the end of the zone. Migration
avoids entering a new zone by never going beyond the free scanned.
Unfortunately, in very rare cases nodes can overlap. When this happens,
migration isolates pages without the LRU lock held, corrupting lists
which will trigger errors in reclaim or during page free such as in the
following oops
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
IP: [<ffffffff810f795c>] free_pcppages_bulk+0xcc/0x450
PGD 1dda554067 PUD 1e1cb58067 PMD 0
Oops: 0000 [#1] SMP
CPU 37
Pid: 17088, comm: memcg_process_s Tainted: G X
RIP: free_pcppages_bulk+0xcc/0x450
Process memcg_process_s (pid: 17088, threadinfo ffff881c2926e000, task ffff881c2926c0c0)
Call Trace:
free_hot_cold_page+0x17e/0x1f0
__pagevec_free+0x90/0xb0
release_pages+0x22a/0x260
pagevec_lru_move_fn+0xf3/0x110
putback_lru_page+0x66/0xe0
unmap_and_move+0x156/0x180
migrate_pages+0x9e/0x1b0
compact_zone+0x1f3/0x2f0
compact_zone_order+0xa2/0xe0
try_to_compact_pages+0xdf/0x110
__alloc_pages_direct_compact+0xee/0x1c0
__alloc_pages_slowpath+0x370/0x830
__alloc_pages_nodemask+0x1b1/0x1c0
alloc_pages_vma+0x9b/0x160
do_huge_pmd_anonymous_page+0x160/0x270
do_page_fault+0x207/0x4c0
page_fault+0x25/0x30
The "X" in the taint flag means that external modules were loaded but but
is unrelated to the bug triggering. The real problem was because the PFN
layout looks like this
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
DMA32 0x00001000 -> 0x00100000
Normal 0x00100000 -> 0x01e80000
Movable zone start PFN for each node
early_node_map[14] active PFN ranges
0: 0x00000010 -> 0x0000009b
0: 0x00000100 -> 0x0007a1ec
0: 0x0007a354 -> 0x0007a379
0: 0x0007f7ff -> 0x0007f800
0: 0x00100000 -> 0x00680000
1: 0x00680000 -> 0x00e80000
0: 0x00e80000 -> 0x01080000
1: 0x01080000 -> 0x01280000
0: 0x01280000 -> 0x01480000
1: 0x01480000 -> 0x01680000
0: 0x01680000 -> 0x01880000
1: 0x01880000 -> 0x01a80000
0: 0x01a80000 -> 0x01c80000
1: 0x01c80000 -> 0x01e80000
The fix is straight-forward. isolate_migratepages() has to make a
similar check to isolate_freepage to ensure that it never isolates pages
from a zone it does not hold the LRU lock for.
This was discovered in a 3.0-based kernel but it affects 3.1.x, 3.2.x
and current mainline.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
nsegs is read from userspace. Limit its value and avoid overflowing nsegs
* sizeof(__u64) in the subsequent call to memdup_user().
This patch complements 481fe17e97 ("nilfs2: potential integer overflow
in nilfs_ioctl_clean_segments()").
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Cc: Haogang Chen <haogangchen@gmail.com>
Acked-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
New pohmelfs is coming, and it is time to remove deadly old design
https://lkml.org/lkml/2012/2/8/293
Signed-off-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to the sysdev conversion to struct device, the cpu objects get
reused when adding a cpu after offlining it, which causes a big warning
that the kobject portion is not properly initialized.
So clear out the object before we register it again, so all is quiet.
Reported-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Those lines have two copies.
Not sure how it could happen, looks like git problem.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9bef3d4197
"serial: group all the 8250 related code together"
inadvertently swept up the m32r driver in the move, because
it had comments mentioning 8250 registers within it. However
these are only there by nature of the driver being based off
the 8250 source code -- the hardware itself does not actually
have any relation to the original 8250 style UARTs.
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A collection of small fixes, mostly for regressions.
In addition, a few ASoC wm8994 updates are included, too.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=87qU
-----END PGP SIGNATURE-----
Merge tag 'sound-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
sound fixes#2 for 3.3-rc3
A collection of small fixes, mostly for regressions.
In addition, a few ASoC wm8994 updates are included, too.
* tag 'sound-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: wm8994: Disable line output discharge prior to ramping VMID
ASoC: wm8994: Fix typo in VMID ramp setting
ALSA: oxygen, virtuoso: fix exchanged L/R volumes of aux and CD inputs
ALSA: usb-audio: add Edirol UM-3G support
ALSA: hda - add support for Uniwill ECS M31EI notebook
ALSA: hda - Fix error handling in patch_ca0132.c
ASoC: wm8994: Enabling VMID should take a runtime PM reference
ALSA: hda/realtek - Fix a wrong condition
ALSA: emu8000: Remove duplicate linux/moduleparam.h include from emu8000_patch.c
ALSA: hda/realtek - Add missing Bass and CLFE as vmaster slaves
ASoC: wm_hubs: Correct line input to line output 2 paths
ASoC: cs42l73: Fix Output [X|A|V]SP_SCLK Sourcing Mode setting for master mode
ASoC: wm8962: Fix word length configuration
ASoC: core: Better support for idle_bias_off suspend ignores
ASoC: wm8994: Remove ASoC level register cache sync
ASoC: wm_hubs: Fix routing of input PGAs to line output mixer
This patch fixes UML build:
CC drivers/staging/android/ram_console.o
drivers/staging/android/ram_console.c: In function
'ram_console_driver_probe':
drivers/staging/android/ram_console.c:358:2: error: implicit declaration
of function 'ioremap' [-Werror=implicit-function-declaration]
cc1: some warnings being treated as errors
make[3]: *** [drivers/staging/android/ram_console.o] Error 1
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In https://bugs.archlinux.org/task/27996, failure of driver r8712u is
reported, with a timeout during module loading due to synchronous loading
of the firmware. The code now uses request_firmware_nowait().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stub_probe function can be called as soon as the stub_driver is
registered. This can lead to the busid_table_lock being used before it
is initialized. Moved calling the init_busid_table function (which
initalizes this spinlock) to be called earlier in the init function to
prevent this from happening.
Signed-off-by: Bart Westgeest <bart@elbrys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When this driver was upgraded to the vendor 20100831 version in
commit 93c55dda09 et al,, one listhead initialization was missed.
This broke complete operation of the driver whenever AP mode was
enabled.
This patch fixes https://bugs.archlinux.org/task/27996.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.stable.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This structure is still used after it has been freed, since it
is being allocated in probe, calls to free it have been moved to
module's remove routine.
This should fix the follwoing messages when attempting to remove the
module:
drv_get_first_dev_extension: Failed to retrieve the object handle
drv_get_first_dev_extension: Failed to retrieve the object handle
drv_destroy: Failed to store DRV object
mgr_destroy: Failed to store MGR object
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two members of pr_ctxt allocated during bridge_open that
are never freed resulting in memory leaks, these are stream_id and
node_id, they are now freed on release of the handle (bridge_release)
right before freeing pr_ctxt.
Error path for bridge_open was also fixed since the same variables
could result in memory leaking due to missing handling of failure
scenarios. While at it, the indentation changes were introduced to
avoid interleaved goto statements inside big if blocks.
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a process forked and the child process was killed by the
lowmemorykiller, the lowmemory killer would be disabled until
the parent process reaped the child or it died itself.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a multithreaded workload, the zv_curr_dist_counts
and zv_cumul_dist_counts statistics are being corrupted
because the increments and decrements in zv_create
and zv_free are not atomic.
This patch converts these statistics and their corresponding
increments/decrements/reads to atomic operations.
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Acked-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add MODULE_LICENSE() for this source module to fix build warning:
WARNING: modpost: missing MODULE_LICENSE() in drivers/staging/media/go7007/go7007-usb.o
see include/linux/module.h for more information
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Ross Cohen <rcohen@snurgle.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Opening the binder driver and sharing the file returned with
other processes (e.g. by calling fork) can crash the kernel.
Prevent these crashes with the following changes:
- Add a mutex to protect against two processes mmapping the
same binder_proc.
- After locking mmap_sem, check that the vma we want to access
(still) points to the same mm_struct.
- Use proc->tsk instead of current to get the files struct since
this is where we get the rlimit from.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Addroid pmem driver is no longer used in any of the Android products.
This patch removes pmem driver from Android staging area
Reference: https://lkml.org/lkml/2012/1/23/183
Signed-off-by: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Programming an image was broken, because odev->buf_offs was not advanced
for val == 0 in append_values(). This regression was introduced in:
commit 1ff12a4aa3
Author: Kevin A. Granade <kevin.granade@gmail.com>
Date: Sat Sep 5 01:03:39 2009 -0500
Staging: asus_oled: Cleaned up checkpatch issues.
Fix the image processing by special-casing val == 0.
I have tested this change on an Asus G50V laptop only.
Cc: Jakub Schmidtke <sjakub@gmail.com>
Cc: Kevin A. Granade <kevin.granade@gmail.com>
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If user-space partially unmaps the driver, binder_vma_open
would dump the kernel stack. This is not a kernel bug however
and will be treated as if the whole area was unmapped once
binder_vma_close gets called.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SWIZ_BITS > 8 results in a much larger number of "tmem_obj"
allocations, likely one per page-placed-in-frontswap. The
tmem_obj is not huge (roughly 100 bytes), but it is large
enough to add a not-insignificant memory overhead to zcache.
The SWIZ_BITS=8 will get roughly the same lock contention
without the space wastage.
The effect of SWIZ_BITS can be thought of as "2^SWIZ_BITS is
the number of unique oids that be generated" (This concept is
limited to frontswap's use of tmem).
Acked-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman