This is the last traces of pausing I/O that we had back some
twenty years ago. Probably was only required for 8MHz ISA
cards running "on the edge" at 12MHz. Anyway it hasn't been
in use for years, so lets just bury it for good.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rather than hardcode 9600, use the existing default_baud parameter (which
also defaults to 9600).
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
CC: Tomoya MORINAGA <tomoya.rohm@gmail.com>
CC: Feng Tang <feng.tang@intel.com>
CC: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For cases where boards with non-default clocks are not yet added to the kernel
or when the clock varies across hardware revisions, it is useful to be
able to specify the UART clock on the kernel command line.
Add the user_uartclk parameter and prefer it, if set, to the default and
board specific UART clock settings. Specify user_uartclock on the command-line
with "pch_uart.user_uartclk=48000000".
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
CC: Tomoya MORINAGA <tomoya.rohm@gmail.com>
CC: Feng Tang <feng.tang@intel.com>
CC: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the Fish River Island II (FRI2) UART clock following the CM-iTC
quirk handling mechanism. Depending on the firmware installed on the device, the
FRI2 uses a 48MHz or a 64MHz UART clock. This is detected with DMI strings.
Add similar UART clock quirk handling to the pch_console_setup() function to
enable kernel messages on boards with non-standard UART clocks.
Per Alan's suggestion, abstract out UART clock selection into
pch_uart_get_uartclk() to avoid code duplication.
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
CC: Tomoya MORINAGA <tomoya.rohm@gmail.com>
CC: Feng Tang <feng.tang@intel.com>
CC: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The term "base baud" refers to the fastest baud rate the device can communicate
at. This is clock/16. pch_uart is using base_baud as the clock itself. Rename
the variables to be semantically correct.
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
CC: Tomoya MORINAGA <tomoya.rohm@gmail.com>
CC: Feng Tang <feng.tang@intel.com>
CC: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In addition to the /32 prescaler, the MPC5200B supports a second
baudrate prescaler /4 to reach higher baudrates.
The current calculation (introduced with commit 0d1f22e4) in the kernel
preferes this low prescaler as often as possible, but with some
imprecise counterparts the communication on low baudrates fails.
According a support-mail from freescale the low prescaler (/4) allows
just 1% tolerance in bittiming in contrast to 4% of the high prescaler
(/32). The prescaler not only affects the baudrate-calculation, but
also the sampling of the bits on the wire.
With this patch, we use the slightly less precise, but higher tolerant
prescaler calculation on low baudrates up to (and including) 115200 baud
and the more precise calculation above.
Tested on a custom MPC5200B board with "fsl,mpc5200b-psc-uart".
Calculation Examples with prescaler (PS) 4 and 32 and divisor (DIV) on
various baudrates. Real stands for the real baudrate generated and Diff
for the differences between:
50 Baud PS 32 DIV 0xa122 Real 50 Diff 0.00%
75 Baud PS 32 DIV 0x6b6c Real 75 Diff 0.00%
110 Baud PS 32 DIV 0x493e Real 110 Diff 0.00%
134 Baud PS 32 DIV 0x3c20 Real 133 Diff 0.75%
150 Baud PS 32 DIV 0x35b6 Real 150 Diff 0.00%
200 Baud PS 32 DIV 0x2849 Real 199 Diff 0.50%
300 Baud PS 4 DIV 0xd6d8 Real 300 Diff 0.00%
PS 32 DIV 0x1adb Real 300 Diff 0.00%
600 Baud PS 4 DIV 0x6b6c Real 600 Diff 0.00%
PS 32 DIV 0x0d6e Real 599 Diff 0.17%
1200 Baud PS 4 DIV 0x35b6 Real 1200 Diff 0.00%
PS 32 DIV 0x06b7 Real 1199 Diff 0.08%
1800 Baud PS 4 DIV 0x23cf Real 1799 Diff 0.06%
PS 32 DIV 0x047a Real 1799 Diff 0.06%
2400 Baud PS 4 DIV 0x1adb Real 2400 Diff 0.00%
PS 32 DIV 0x035b Real 2401 Diff - 0.04%
4800 Baud PS 4 DIV 0x0d6e Real 4799 Diff 0.02%
PS 32 DIV 0x01ae Real 4796 Diff 0.08%
9600 Baud PS 4 DIV 0x06b7 Real 9598 Diff 0.02%
PS 32 DIV 0x00d7 Real 9593 Diff 0.07%
19200 Baud PS 4 DIV 0x035b Real 19208 Diff - 0.04%
PS 32 DIV 0x006b Real 19275 Diff - 0.39%
38400 Baud PS 4 DIV 0x01ae Real 38372 Diff 0.07%
PS 32 DIV 0x0036 Real 38194 Diff 0.54%
57600 Baud PS 4 DIV 0x011e Real 57692 Diff - 0.16%
PS 32 DIV 0x0024 Real 57291 Diff 0.54%
76800 Baud PS 4 DIV 0x00d7 Real 76744 Diff 0.07%
PS 32 DIV 0x001b Real 76388 Diff 0.54%
115200 Baud PS 4 DIV 0x008f Real 115384 Diff - 0.16%
PS 32 DIV 0x0012 Real 114583 Diff 0.54%
153600 Baud PS 4 DIV 0x006b Real 154205 Diff - 0.39%
PS 32 DIV 0x000d Real 158653 Diff - 3.29%
230400 Baud PS 4 DIV 0x0048 Real 229166 Diff 0.54%
PS 32 DIV 0x0009 Real 229166 Diff 0.54%
307200 Baud PS 4 DIV 0x0036 Real 305555 Diff 0.54%
PS 32 DIV 0x0007 Real 294642 Diff 4.09%
460800 Baud PS 4 DIV 0x0024 Real 458333 Diff 0.54%
PS 32 DIV 0x0005 Real 412500 Diff 10.48%
500000 Baud PS 4 DIV 0x0021 Real 500000 Diff 0.00%
PS 32 DIV 0x0004 Real 515625 Diff - 3.13%
576000 Baud PS 4 DIV 0x001d Real 568965 Diff 1.22%
PS 32 DIV 0x0004 Real 515625 Diff 10.48%
614400 Baud PS 4 DIV 0x001b Real 611111 Diff 0.54%
PS 32 DIV 0x0003 Real 687500 Diff -11.90%
921600 Baud PS 4 DIV 0x0012 Real 916666 Diff 0.54%
PS 32 DIV 0x0002 Real 1031250 Diff -11.90%
1000000 Baud PS 4 DIV 0x0011 Real 970588 Diff 2.94%
PS 32 DIV 0x0002 Real 1031250 Diff - 3.13%
1152000 Baud PS 4 DIV 0x000e Real 1178571 Diff - 2.31%
PS 32 DIV 0x0002 Real 1031250 Diff 10.48%
1500000 Baud PS 4 DIV 0x000b Real 1500000 Diff 0.00%
PS 32 DIV 0x0001 Real 2062500 Diff -37.50%
2000000 Baud PS 4 DIV 0x0008 Real 2062500 Diff - 3.13%
PS 32 DIV 0x0001 Real 2062500 Diff - 3.13%
2500000 Baud PS 4 DIV 0x0007 Real 2357142 Diff 5.71%
PS 32 DIV 0x0001 Real 2062500 Diff 17.50%
3000000 Baud PS 4 DIV 0x0006 Real 2750000 Diff 8.33%
PS 32 DIV 0x0001 Real 2062500 Diff 31.25%
3500000 Baud PS 4 DIV 0x0005 Real 3300000 Diff 5.71%
PS 32 DIV 0x0001 Real 2062500 Diff 41.07%
4000000 Baud PS 4 DIV 0x0004 Real 4125000 Diff - 3.13%
PS 32 DIV 0x0001 Real 2062500 Diff 48.44%
Signed-off-by: Frank Benkert <frank.benkert@avat.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is supposed to be doing a shift before the comparison instead of
just doing a bitwise AND directly. The current code means the start()
just returns without doing anything.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let us port the code to use tty_port. We now use open_count and tty
from there. This allows us also to use tty_port_tty_set with tty
refcounting instead of hand-written locking and logic.
Note that tty and open_count are no longer protected by cs->lock. It is
protected by tty_port->lock. But since all the places where they were
used are now switched to the helpers, we are fine.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Cc: <gigaset307x-common@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Close the window in open where driver_data is reset to NULL on each
open. It could cause other processes to get invalid retval from the
tty->ops operations because of the checks all over the code.
With this change we may do other cleanups. Now, the only valid check
for tty->driver_data != NULL is in close. This can happen only if open
fails at gigaset_get_cs_by_tty or try_module_get. The rest of checks
in various tty->ops->* are invalid as driver_data cannot be NULL
there. The same holds for cs->open_count. So remove them.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: gigaset307x-common@lists.sourceforge.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of digging a tty out of the tty_driver struct, which is not
defined to work, use tty_port properly. This includes proper tty
refcounting even though there is no possible race currently. But we
will need tty_port for tty buffers in the future anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The timer is initialized too late. tty->open may fire an invalid
timer. So initialize the timer earlier using DEFINE_TIMER.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty->count test in the timer was racy. Let's remove the test and
properly delete the timer and wait for the body to finish using _sync
version of del_timer.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Again, no need to duplicate the code. Let's use the helper.
Amiserial changes are only free of compilation errors. I have no
access to the hardware.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hmm, the code was sleeping with interrupts disabled. This was not
good. Fix this by turning interrupts at an appropriate place. (The
race is protected by CLOSING flag.)
After the move, the code is identical to tty_port_close_end, so use
it!
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a preparation for a switch to tty_port_block_til_ready. We
need amiga_carrier_raised and amiga_dtr_rts. The implementation is
taken from startup, shutdown and current block_til_ready.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amiserial is the last user of serialP.h. Let's move struct
serial_state directly to amiserial and remove serialP crap from
includes. Finally, remove the header from the tree completely.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* instead of line, use tty->index or iterator...
* irq and type are left unset. So get rid of them.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
And use it to make the code more readable.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* remove pointless checks (tty cannot be NULL at that points)
* fix some printks (use __func__, print text directly w/o using global
strings)
* remove some empty lines
This is the last patch for simserial. Overall, the driver is 400 lines
shorter. Being now at 560 lines.
It was tested using ski with a busybox userspace.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the code to conform to the standard. Also make it readable.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Or the obsolete ones like:
"Let's have a little bit of fun"
I have never had fun with software. For fun, one needs hard-ware.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert shutdown to be tty_port_operations->shutdown. Then we can use
tty_port_hangup. (And we have to use tty_port_close.)
This means we no longer touch ASYNC_INITIALIZED, TTY_IO_ERROR. Also we
do not need to do any peculiar TTY logic in the file now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So now we convert startup to be ->activate of tty_port. This means we
no longer care about INITIALIZED and TTY_IO_ERROR flags.
After we have ->activate much of the code may go as it duplicates what
tty_port_open does. In this case tty_port_open adds block_til_ready to
the path. But we do not define carrier hooks, so it is a noop.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So that we will not be surprised in the ISR anymore.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I.e. remove more copied bloat.
The only change is that we wait_until_sent now. Which is what we
really should do.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code is identical except locking. But added locks to protect
counts do not hurt here. Rather the contrary.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All ->start, ->stop and ->wait_until_sent are empty and need not be
defined. The time to remove them is now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
And use it to make the code more readable.
Since tport doesn't conflict with port anymore and there are not many
tport accessors left, do also s/\<tport\>/port/g.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's do a spin-off of serial_state structure with only needed
elements.
And remove serialP crap from includes.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* instead of line, use tty->index or an iterator
* icount is not made public, only the tx path increments it
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We do not use any of the preinitialized rs_state members for something
real. So there is no need to initialize them. At the places we used
them for printing, just print the values.
And since only one port is supported, get rid of the loop. This
simplifies simrs_init a heap. Thus we can handle fail paths in a
standard way without panicing.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This changes flags' type to ulong which is appropriate for all the
set/clear_bits performed in the drivers..
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nothing special. Just remove count from serial_state and change all
users to use tty_port.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Note that previously simserial set the delay to 0. So we preserve
that. BUT, is it correct?
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add tty_port to serial_state and start using common tty port members
from tty_port in amiserial and simserial. The rest will follow one by
one.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This avoids pain with tty refcounting and touching tty_port in the
future. It allows us to remove some state->tty tests because the tty
passed down to them can never be NULL.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This avoids pain with tty refcounting and touching tty_port in the
future. It allows us to remove some info->tty tests because the tty
passed down to them can never be NULL.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not copy whole serial_state. We only need to know whether the speed
is to be changed. Hence store the info in advance and use it later.
A simple bool is enough.
Also remove reduntant assignments and move the tests directly to the
'if'.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the final step to get rid of the one of the structures. A
further cleanup will follow. And I struct serial_state deserves cease
to exist after a switch to tty_port too.
While changing the lines, it removes also pointless tty->driver_data
casts.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
They used to work as a storage for 'info' pointer used in ISRs. They
are not really needed. Just pass the pointer through request_irq to
the handlers.
It was set to NULL and tested in the ISRs, but we do not need the
tests as we disable all the interrupts at the same places where NULL
sets were.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We do not set ASYNC_SHARE_IRQ anywhere. And since IRQF_DISABLED is a
noop, pass zero to request_irq directly instead of this ugly macro.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It never worked there. The ISR was never written for that kind of
stuff. So remove all that crap with a hash of linked lists and pass
the pointer directly to the ISR.
BTW this answers the question there:
* I don't know exactly why they don't use the dev_id opaque data
* pointer instead of this extra lookup table
-> Because they thought they will support more devices bound to a
single interrupt w/o IRQF_SHARED. They would need exactly the hash
there.
What I don't understand is rebinding of the interrupt in the shutdown
path. They perhaps meant to do just synchronize_irq? In any case, this
is all gone and free_irq there properly.
By removing the hash we save some bits (exactly NR_IRQS * 8 bytes of
.bss and over a kilo of .text):
before:
text data bss dec hex filename
19600 320 8227 28147 6df3 ../a/ia64/arch/ia64/hp/sim/simserial.o
after:
text data bss dec hex filename
18568 320 28 18916 49e4 ../a/ia64/arch/ia64/hp/sim/simserial.o
Note that a shared interrupt could not work too. request_irq requires
data parameter to be non-NULL. So the whole IRQ_T exercise was
pointless.
Finally, this helps us remove another two members of async_struct :).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This means:
* close_delay
* closing_wait
* line
* port
* xmit_fifo_size
This actually fixes a bug in amiserial. It initializes one and uses
the other of the close delays. Yes, duplicating structure members is
evil.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The same as for amiserial. Use only one instance of the flags.
Also remove them from async_struct now. Nobody else uses them.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without this, the code succeeds when the port is opened by root and we
get unwanted interrupts storm on the first key stroke.
Instead of that, tell the user we failed and that we won't continue. I
suppose, the code was copied from the serial layer where we may want
to change the irq number, so we must allow open even of the failing
port. This is not the case for this driver at all.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul Gortmaker