Define get_guest_storage_key which can be used to get the value of a guest
storage key. This compliments the functionality provided by the helper function
set_guest_storage_key. Both functions are needed for live migration of s390
guests that use storage keys.
Signed-off-by: Jason J. Herne <jjherne@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
When injecting a floating interrupt and no CPU is idle we
kick one CPU to do an external exit. In case of I/O we
should trigger an I/O exit instead. This does not matter
for Linux guests as external and I/O interrupts are
enabled/disabled at the same time, but play safe anyway.
The same holds true for machine checks. Since there is no
special exit, just reuse the generic stop exit. The injection
code inside the VCPU loop will recheck anyway and rearm the
proper exits (e.g. control registers) if necessary.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
A couple of our interception handlers rewind the PSW to the beginning
of the instruction to run the intercepted instruction again during the
next SIE entry. This normally works fine, but there is also the
possibility that the instruction did not get run directly but via an
EXECUTE instruction.
In this case, the PSW does not point to the instruction that caused the
interception, but to the EXECUTE instruction! So we've got to rewind the
PSW to the beginning of the EXECUTE instruction instead.
This is now accomplished with a new helper function kvm_s390_rewind_psw().
Signed-off-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
This patch includes two small fixes for the PFMF handler: First, the
start address for PFMF has to be masked according to the current
addressing mode, which is now done with kvm_s390_logical_to_effective().
Second, the protection exceptions have a lower priority than the
specification exceptions, so the check for low-address protection
has to be moved after the last spot where we inject a specification
exception.
Signed-off-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Simplify cpu_relax() to a simple barrier(). Performance wise this doesn't
seem to make any big difference anymore, since nearly all lock variants
have directed yield semantics in the meantime.
Also this makes s390 behave like all other architectures.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The debug_unregister() function performs also input parameter validation.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The common code ftrace_return_address(n), which is just a wrapper for
__builtin_return_address(n), will only work for n > 0 if CONFIG_FRAME_POINTER
is set to 'y'. Otherwise it will return 0.
Since on s390 we will never have that config option set to 'y'
ftrace_return_address() won't work at all for n > 0.
Luckily we always compile the kernel with -mkernel-backchain which
in turn means that __builtin_return_address(n) will always work.
So let ftrace_return_address(n) map to __builtin_return_address(n).
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This prefixes all crypto module loading with "crypto-" so we never run
the risk of exposing module auto-loading to userspace via a crypto API,
as demonstrated by Mathias Krause:
https://lkml.org/lkml/2013/3/4/70
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The PCI/MSI irq chip callbacks mask/unmask_msi_irq have been renamed
to pci_msi_mask/unmask_irq to mark them PCI specific. Rename all usage
sites. The conversion helper functions are kept around to avoid
conflicts in next and will be removed after merging into mainline.
Coccinelle assisted conversion. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: x86@kernel.org
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Mohit Kumar <mohit.kumar@st.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Yijing Wang <wangyijing@huawei.com>
mask/unmask_msi_irq and __mask_msi/msix_irq are PCI/MSI specific
functions and should be named accordingly. This is a preparatory patch
to support MSI on non PCI devices.
Rename mask/unmask_msi_irq to pci_msi_mask/unmask_irq and document the
functions. Provide conversion helpers.
Rename __mask_msi/msix_irq to __pci_msi/msix_desc_mask so its clear
that they operated on msi_desc. Fixup the only user outside of
pci/msi.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Rename write_msi_msg() to pci_write_msi_msg() to mark it as PCI
specific.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Translation exceptions should never happen, since that implies that
either we screwed up the page tables or missed to properly flush the TLB.
In both cases we should not just simply kill user space or walk the kernel
exception tables. Instead an oops or a panic (panic_on_oops) is the better
answer.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
It always confuses me to see the mixed instruction length code and
interruption code on user space faults, while the message clearly
says it is the interruption code.
So split the value and print both values separately. Also add the ILC
output to the die() message, so thar user and kernel space faults
contain the same information.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The x86 MPX patch set calls arch_unmap() and arch_bprm_mm_init()
from fs/exec.c, so we need at least a stub for them in all
architectures. They are only called under an #ifdef for
CONFIG_MMU=y, so we can at least restict this to architectures
with MMU support.
blackfin/c6x have no MMU support, so do not call arch_unmap().
They also do not include mm_hooks.h or mmu_context.h at all and
do not need to be touched.
s390, um and unicore32 do not use asm-generic/mm_hooks.h, so got
their own arch_unmap() versions. (I also moved um's
arch_dup_mmap() to be closer to the other mm_hooks.h functions).
xtensa only includes mm_hooks when MMU=y, which should be fine
since arch_unmap() is called only from MMU=y code.
For the rest, we use the stub copies of these functions in
asm-generic/mm_hook.h.
I cross compiled defconfigs for cris (to check NOMMU) and s390
to make sure that this works. I also checked a 64-bit build
of UML and all my normal x86 builds including PARAVIRT on and
off.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: linux-arch@vger.kernel.org
Cc: x86@kernel.org
Link: http://lkml.kernel.org/r/20141118182350.8B4AA2C2@viggo.jf.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add the new __NR_s390_pci_mmio_write and __NR_s390_pci_mmio_read
system calls to allow user space applications to access device PCI I/O
memory pages on s390x platform.
[ Martin Schwidefsky: some code beautification ]
Signed-off-by: Alexey Ishchuk <aishchuk@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The floating point registers of a process that uses vector instruction are
not store into task->thread.fp_regs anymore but in the upper halves of the
first 16 vector registers.
The ptrace interface for the peeks and pokes to the user area fails to take
this into account. Fix __peek_user[_compat] and __poke_user[_compat]
to use the vector array for the floating pointer register if the process
has one.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Irq 0 is currently unused on s390. Since there is no reason to
do this start counting at the beginning and gain an additional
irq. Also correctly report the smallest usable irq number for
dynamic allocation.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
add ioport_map stubs to make vfio build on s390.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Conflicts:
drivers/net/ethernet/chelsio/cxgb4vf/sge.c
drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
sge.c was overlapping two changes, one to use the new
__dev_alloc_page() in net-next, and one to use s->fl_pg_order in net.
ixgbe_phy.c was a set of overlapping whitespace changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Now only s390/MSI use default_msi_mask_irq() and default_msix_mask_irq(),
replace them with the common MSI mask IRQ functions __msi_mask_irq() and
__msix_mask_irq(). Remove default_msi_mask_irq() and
default_msix_mask_irq().
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
CC: linux-s390@vger.kernel.org
Alternative to RPS/RFS is to use hardware support for multiple
queues.
Then split a set of million of sockets into worker threads, each
one using epoll() to manage events on its own socket pool.
Ideally, we want one thread per RX/TX queue/cpu, but we have no way to
know after accept() or connect() on which queue/cpu a socket is managed.
We normally use one cpu per RX queue (IRQ smp_affinity being properly
set), so remembering on socket structure which cpu delivered last packet
is enough to solve the problem.
After accept(), connect(), or even file descriptor passing around
processes, applications can use :
int cpu;
socklen_t len = sizeof(cpu);
getsockopt(fd, SOL_SOCKET, SO_INCOMING_CPU, &cpu, &len);
And use this information to put the socket into the right silo
for optimal performance, as all networking stack should run
on the appropriate cpu, without need to send IPI (RPS/RFS).
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xlate_dev_{kmem,mem}_ptr() functions take either a physical address
or a kernel virtual address, so data types should be phys_addr_t and
void *. They both return a kernel virtual address which is only ever
used in calls to copy_{from,to}_user(), so make variables that store it
void * rather than char * for consistency.
Also only define a weak unxlate_dev_mem_ptr() function if architectures
haven't overridden them in the asm/io.h header file.
Signed-off-by: Thierry Reding <treding@nvidia.com>
1. We should flush TLBs for load control instruction emulation (stable)
2. A workaround for a compiler bug that renders ACCESS_ONCE broken (stable)
3. Fix program check handling for load control
4. Documentation Fix
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=kFKq
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-next-20141107' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD
KVM: s390: Fixes for kvm/next (3.19) and stable
1. We should flush TLBs for load control instruction emulation (stable)
2. A workaround for a compiler bug that renders ACCESS_ONCE broken (stable)
3. Fix program check handling for load control
4. Documentation Fix
According to the architecture all instructions are suppressing if memory
access is prohibited due to DAT protection, unless stated otherwise for
an instruction.
The lctl[g]/stctl[g] implementations handled this incorrectly since
control register handling was done piecemeal, which means they had
terminating instead of suppressing semantics.
This patch fixes this.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
some control register changes will flush some aspects of the CPU, e.g.
POP explicitely mentions that for CR9-CR11 "TLBs may be cleared".
Instead of trying to be clever and only flush on specific CRs, let
play safe and flush on all lctl(g) as future machines might define
new bits in CRs. Load control intercept should not happen that often.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
ipte_unlock_siif uses cmpxchg to replace the in-memory data of the ipte
lock together with ACCESS_ONCE for the intial read.
union ipte_control {
unsigned long val;
struct {
unsigned long k : 1;
unsigned long kh : 31;
unsigned long kg : 32;
};
};
[...]
static void ipte_unlock_siif(struct kvm_vcpu *vcpu)
{
union ipte_control old, new, *ic;
ic = &vcpu->kvm->arch.sca->ipte_control;
do {
new = old = ACCESS_ONCE(*ic);
new.kh--;
if (!new.kh)
new.k = 0;
} while (cmpxchg(&ic->val, old.val, new.val) != old.val);
if (!new.kh)
wake_up(&vcpu->kvm->arch.ipte_wq);
}
The new value, is loaded twice from memory with gcc 4.7.2 of
fedora 18, despite the ACCESS_ONCE:
--->
l %r4,0(%r3) <--- load first 32 bit of lock (k and kh) in r4
alfi %r4,2147483647 <--- add -1 to r4
llgtr %r4,%r4 <--- zero out the sign bit of r4
lg %r1,0(%r3) <--- load all 64 bit of lock into new
lgr %r2,%r1 <--- load the same into old
risbg %r1,%r4,1,31,32 <--- shift and insert r4 into the bits 1-31 of
new
llihf %r4,2147483647
ngrk %r4,%r1,%r4
jne aa0 <ipte_unlock+0xf8>
nihh %r1,32767
lgr %r4,%r2
csg %r4,%r1,0(%r3)
cgr %r2,%r4
jne a70 <ipte_unlock+0xc8>
If the memory value changes between the first load (l) and the second
load (lg) we are broken. If that happens VCPU threads will hang
(unkillable) in handle_ipte_interlock.
Andreas Krebbel analyzed this and tracked it down to a compiler bug in
that version:
"while it is not that obvious the C99 standard basically forbids
duplicating the memory access also in that case. For an argumentation of
a similiar case please see:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=22278#c43
For the implementation-defined cases regarding volatile there are some
GCC-specific clarifications which can be found here:
https://gcc.gnu.org/onlinedocs/gcc/Volatiles.html#Volatiles
I've tracked down the problem with a reduced testcase. The problem was
that during a tree level optimization (SRA - scalar replacement of
aggregates) the volatile marker is lost. And an RTL level optimizer (CSE
- common subexpression elimination) then propagated the memory read into
its second use introducing another access to the memory location. So
indeed Christian's suspicion that the union access has something to do
with it is correct (since it triggered the SRA optimization).
This issue has been reported and fixed in the GCC 4.8 development cycle:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=58145"
This patch replaces the ACCESS_ONCE scheme with a barrier() based scheme
that should work for all supported compilers.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: stable@vger.kernel.org # v3.16+
Pull s390 update from Martin Schwidefsky:
"One small improvement for the cputime accounting, two bug fixes and an
update for the default configuration files"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/ftrace: add ftrace_graph_is_dead() check
s390: update default configuration
s390/vdso: fix stack corruption
s390/time: use stck clock fast for do_account_vtime
The git commit c719f56092
"perf: Fix and clean up initialization of pmu::event_idx" removed
the PMU event index callback for all architectures but x86,
remove the initialization of the event index as well.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix the following warnings from the sparse code checker:
arch/s390/kernel/signal.c:374:38: warning: cast removes address space of expression
arch/s390/kernel/signal.c:374:65: warning: incorrect type in initializer (different address spaces)
arch/s390/kernel/signal.c:374:65: expected unsigned short [noderef] [usertype] <asn:1>*svc
arch/s390/kernel/signal.c:374:65: got void *
arch/s390/kernel/compat_signal.c:437:38: warning: cast removes address space of expression
arch/s390/kernel/compat_signal.c:437:65: warning: incorrect type in initializer (different address spaces)
arch/s390/kernel/compat_signal.c:437:65: expected unsigned short [noderef] [usertype] <asn:1>*svc
arch/s390/kernel/compat_signal.c:437:65: got void *
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The page table lock is acquired with a call to get_locked_pte,
replace the plain spin_unlock with the correct unlock function
pte_unmap_unlock.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix the following warnings from the sparse code checker:
arch/s390/include/asm/pci_io.h:165:49: warning: cast removes address space of expression
arch/s390/pci/pci.c:476:44: warning: cast removes address space of expression
arch/s390/pci/pci.c:491:36: warning: incorrect type in argument 2 (different address spaces)
arch/s390/pci/pci.c:491:36: expected void [noderef] <asn:2>*addr
arch/s390/pci/pci.c:491:36: got void *<noident>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
s390s arch_setup_msi_irqs function ensures that we don't return with
more irqs than the PCI architecture allows and that a single PCI
function doesn't consume more irqs than the kernel is configured for.
At least the last check doesn't help much and should take the sum of
all irqs into account. Since that's already done by irq_alloc_desc
we can remove this check.
As for the first check we should use the value provided by the
firmware which can be less than what the PCI architecture allows.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The kernel build for s390 fails for gcc compilers with version 3.x,
set the minimum required version of gcc to version 4.3.
As the atomic builtins are available with all gcc 4.x compilers,
use the __sync_val_compare_and_swap and __sync_bool_compare_and_swap
functions to replace the complex macro and inline assembler magic
in include/asm/cmpxchg.h. The compiler can just-do-it and generates
better code with the builtins.
While we are at it use __sync_bool_compare_and_swap for the
_raw_compare_and_swap function in the spinlock code as well.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, plus on the kernel side:
- a revert for a newly introduced PMU driver which isn't complete yet
and where we ran out of time with fixes (to be tried again in
v3.19) - this makes up for a large chunk of the diffstat.
- compilation warning fixes
- a printk message fix
- event_idx usage fixes/cleanups"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf probe: Trivial typo fix for --demangle
perf tools: Fix report -F dso_from for data without branch info
perf tools: Fix report -F dso_to for data without branch info
perf tools: Fix report -F symbol_from for data without branch info
perf tools: Fix report -F symbol_to for data without branch info
perf tools: Fix report -F mispredict for data without branch info
perf tools: Fix report -F in_tx for data without branch info
perf tools: Fix report -F abort for data without branch info
perf tools: Make CPUINFO_PROC an array to support different kernel versions
perf callchain: Use global caching provided by libunwind
perf/x86/intel: Revert incomplete and undocumented Broadwell client support
perf/x86: Fix compile warnings for intel_uncore
perf: Fix typos in sample code in the perf_event.h header
perf: Fix and clean up initialization of pmu::event_idx
perf: Fix bogus kernel printk
perf diff: Add missing hists__init() call at tool start
In preparation for further code changes (e.g. getting rid of action_flags),
this patch splits the handling of the two sigp orders SIGP STOP and SIGP STOP
AND STORE STATUS by introducing a separate handler function for SIGP STOP AND
STORE STATUS.
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
In preparation for further code changes, this patch moves the injection of
emergency calls into a separate function and uses it for the processing of
SIGP EMERGENCY CALL and SIGP CONDITIONAL EMERGENCY CALL.
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
This patch introduces instruction counters for all known sigp orders and also a
separate one for unknown orders that are passed to user space.
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
This patch introduces in preparation for further code changes separate handler
functions for:
- SIGP (RE)START - will not be allowed to terminate pending orders
- SIGP (INITIAL) CPU RESET - will be allowed to terminate certain pending orders
- unknown sigp orders
All sigp orders that require user space intervention are logged.
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
All sigp orders targeting one VCPU have to verify that the target is valid and
available.
Let's move the check from the single functions to the dispatcher. The
destination VCPU is directly passed as a pointer - instead of the cpu address of
the target.
Please note that all SIGP orders except SIGP SET ARCHITECTURE - even unknown
ones - will now check for the availability of the target VCPU. This is what the
architecture documentation specifies.
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
All sigp orders except SIGP SET ARCHITECTURE target exactly one vcpu.
Let's move the dispatch code for these orders into a separate function to
prepare for cleaner target availability checks.
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The monitor-class number field is only 16 bits, so we have to use
a u16 pointer to access it.
Signed-off-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
CC: stable@vger.kernel.org # v3.16+
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
In set_guest_storage_key, we really want to reference the mm struct given as
a parameter to the function. So replace the current->mm reference with the
mm struct passed in by the caller.
Signed-off-by: Jason J. Herne <jjherne@us.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
The ipte-locking should be done for each VM seperately, not globally.
This way we avoid possible congestions when the simple ipte-lock is used
and multiple VMs are running.
Suggested-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Andy reported that the current state of event_idx is rather confused.
So remove all but the x86_pmu implementation and change the default to
return 0 (the safe option).
Reported-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Cody P Schafer <cody@linux.vnet.ibm.com>
Cc: Cody P Schafer <dev@codyps.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Himangi Saraogi <himangi774@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: sukadev@linux.vnet.ibm.com <sukadev@linux.vnet.ibm.com>
Cc: Thomas Huth <thuth@linux.vnet.ibm.com>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: linux390@de.ibm.com
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-s390@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add an ftrace_graph_is_dead() check to prepare_ftrace_return() in order to
detect an internal ftrace graph error. This allows to prevent further ftrace
graph handling and hopefully keeps the kernel alive.
This patch is the same like for all other architectures.
For unkown reasons s390 was left out.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Analog to ptep_get_and_clear_full define a variant of the
pmpd_get_and_clear primitive which gets the full hint from the
mmu_gather struct. This allows s390 to avoid a costly instruction
when destroying an address space.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After fixup_user_fault does not fail we have a writeable pte.
That pte might transform but it should not vanish.
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use NOKPROBE_SYMBOL() instead of __kprobes annotation.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the function tracer is enabled, allow to set kprobes on the first
instruction of a function (which is the function trace caller):
If no kprobe is set handling of enabling and disabling function tracing
of a function simply patches the first instruction. Either it is a nop
(right now it's an unconditional branch, which skips the mcount block),
or it's a branch to the ftrace_caller() function.
If a kprobe is being placed on a function tracer calling instruction
we encode if we actually have a nop or branch in the remaining bytes
after the breakpoint instruction (illegal opcode).
This is possible, since the size of the instruction used for the nop
and branch is six bytes, while the size of the breakpoint is only
two bytes.
Therefore the first two bytes contain the illegal opcode and the last
four bytes contain either "0" for nop or "1" for branch. The kprobes
code will then execute/simulate the correct instruction.
Instruction patching for kprobes and function tracer is always done
with stop_machine(). Therefore we don't have any races where an
instruction is patched concurrently on a different cpu.
Besides that also the program check handler which executes the function
trace caller instruction won't be executed concurrently to any
stop_machine() execution.
This allows to keep full fault based kprobes handling which generates
correct pt_regs contents automatically.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When storage keys are enabled unmerge already merged pages and prevent
new pages from being merged.
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
As soon as storage keys are enabled we need to stop working on zero page
mappings to prevent inconsistencies between storage keys and pgste.
Otherwise following data corruption could happen:
1) guest enables storage key
2) guest sets storage key for not mapped page X
-> change goes to PGSTE
3) guest reads from page X
-> as X was not dirty before, the page will be zero page backed,
storage key from PGSTE for X will go to storage key for zero page
4) guest sets storage key for not mapped page Y (same logic as above
5) guest reads from page Y
-> as Y was not dirty before, the page will be zero page backed,
storage key from PGSTE for Y will got to storage key for zero page
overwriting storage key for X
While holding the mmap sem, we are safe against changes on entries we
already fixed, as every fault would need to take the mmap_sem (read).
Other vCPUs executing storage key instructions will get a one time interception
and be serialized also with mmap_sem.
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Replace the s390 specific page table walker for the pgste updates
with a call to the common code walk_page_range function.
There are now two pte modification functions, one for the reset
of the CMMA state and another one for the initialization of the
storage keys.
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The kernel provided vdso functions do not get a stack frame from the
calling function and therefore may not change the stack contents, unless
they allocate space on their own.
This problem was exposed with 070b7be633 "s390/vdso: replace stck with
stcke" which writes 16 bytes instead of 8 bytes into the stack frame. These
additional 8 bytes however were indeed used by the caller (glibc) to save
data and therefore this data was corrupted by the vdso code.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The last high frequency call site of the STCK instruction is
do_account_vtime. Replace it with the faster STCKF instruction.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull s390 updates from Martin Schwidefsky:
"One patch to enable the BPF system call and three more bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/uprobes: fix kprobes dependency
s390: wire up bpf syscall
s390/mm: fixing calls of pte_unmap_unlock
s390/hmcdrv: Restrict s390 HMC driver to S390 arch
These are now defined by asm-generic/io.h, so we don't need the private
definitions anymore.
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Pull audit updates from Eric Paris:
"So this change across a whole bunch of arches really solves one basic
problem. We want to audit when seccomp is killing a process. seccomp
hooks in before the audit syscall entry code. audit_syscall_entry
took as an argument the arch of the given syscall. Since the arch is
part of what makes a syscall number meaningful it's an important part
of the record, but it isn't available when seccomp shoots the
syscall...
For most arch's we have a better way to get the arch (syscall_get_arch)
So the solution was two fold: Implement syscall_get_arch() everywhere
there is audit which didn't have it. Use syscall_get_arch() in the
seccomp audit code. Having syscall_get_arch() everywhere meant it was
a useless flag on the stack and we could get rid of it for the typical
syscall entry.
The other changes inside the audit system aren't grand, fixed some
records that had invalid spaces. Better locking around the task comm
field. Removing some dead functions and structs. Make some things
static. Really minor stuff"
* git://git.infradead.org/users/eparis/audit: (31 commits)
audit: rename audit_log_remove_rule to disambiguate for trees
audit: cull redundancy in audit_rule_change
audit: WARN if audit_rule_change called illegally
audit: put rule existence check in canonical order
next: openrisc: Fix build
audit: get comm using lock to avoid race in string printing
audit: remove open_arg() function that is never used
audit: correct AUDIT_GET_FEATURE return message type
audit: set nlmsg_len for multicast messages.
audit: use union for audit_field values since they are mutually exclusive
audit: invalid op= values for rules
audit: use atomic_t to simplify audit_serial()
kernel/audit.c: use ARRAY_SIZE instead of sizeof/sizeof[0]
audit: reduce scope of audit_log_fcaps
audit: reduce scope of audit_net_id
audit: arm64: Remove the audit arch argument to audit_syscall_entry
arm64: audit: Add audit hook in syscall_trace_enter/exit()
audit: x86: drop arch from __audit_syscall_entry() interface
sparc: implement is_32bit_task
sparc: properly conditionalize use of TIF_32BIT
...
If kprobes is disabled uprobes will not compile.
Fix this by including the correct header files.
Signed-off-by: Jan Willeke <willeke@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
pte_unmap works on page table entry pointers, derefencing should be avoided.
As on s390 pte_unmap is a NOP, this is more a cleanup if we want to supply
later such function.
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Reviewed-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull percpu consistent-ops changes from Tejun Heo:
"Way back, before the current percpu allocator was implemented, static
and dynamic percpu memory areas were allocated and handled separately
and had their own accessors. The distinction has been gone for many
years now; however, the now duplicate two sets of accessors remained
with the pointer based ones - this_cpu_*() - evolving various other
operations over time. During the process, we also accumulated other
inconsistent operations.
This pull request contains Christoph's patches to clean up the
duplicate accessor situation. __get_cpu_var() uses are replaced with
with this_cpu_ptr() and __this_cpu_ptr() with raw_cpu_ptr().
Unfortunately, the former sometimes is tricky thanks to C being a bit
messy with the distinction between lvalues and pointers, which led to
a rather ugly solution for cpumask_var_t involving the introduction of
this_cpu_cpumask_var_ptr().
This converts most of the uses but not all. Christoph will follow up
with the remaining conversions in this merge window and hopefully
remove the obsolete accessors"
* 'for-3.18-consistent-ops' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (38 commits)
irqchip: Properly fetch the per cpu offset
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t -fix
ia64: sn_nodepda cannot be assigned to after this_cpu conversion. Use __this_cpu_write.
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t
Revert "powerpc: Replace __get_cpu_var uses"
percpu: Remove __this_cpu_ptr
clocksource: Replace __this_cpu_ptr with raw_cpu_ptr
sparc: Replace __get_cpu_var uses
avr32: Replace __get_cpu_var with __this_cpu_write
blackfin: Replace __get_cpu_var uses
tile: Use this_cpu_ptr() for hardware counters
tile: Replace __get_cpu_var uses
powerpc: Replace __get_cpu_var uses
alpha: Replace __get_cpu_var
ia64: Replace __get_cpu_var uses
s390: cio driver &__get_cpu_var replacements
s390: Replace __get_cpu_var uses
mips: Replace __get_cpu_var uses
MIPS: Replace __get_cpu_var uses in FPU emulator.
arm: Replace __this_cpu_ptr with raw_cpu_ptr
...
Pull s390 updates from Martin Schwidefsky:
"This patch set contains the main portion of the changes for 3.18 in
regard to the s390 architecture. It is a bit bigger than usual,
mainly because of a new driver and the vector extension patches.
The interesting bits are:
- Quite a bit of work on the tracing front. Uprobes is enabled and
the ftrace code is reworked to get some of the lost performance
back if CONFIG_FTRACE is enabled.
- To improve boot time with CONFIG_DEBIG_PAGEALLOC, support for the
IPTE range facility is added.
- The rwlock code is re-factored to improve writer fairness and to be
able to use the interlocked-access instructions.
- The kernel part for the support of the vector extension is added.
- The device driver to access the CD/DVD on the HMC is added, this
will hopefully come in handy to improve the installation process.
- Add support for control-unit initiated reconfiguration.
- The crypto device driver is enhanced to enable the additional AP
domains and to allow the new crypto hardware to be used.
- Bug fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (39 commits)
s390/ftrace: simplify enabling/disabling of ftrace_graph_caller
s390/ftrace: remove 31 bit ftrace support
s390/kdump: add support for vector extension
s390/disassembler: add vector instructions
s390: add support for vector extension
s390/zcrypt: Toleration of new crypto hardware
s390/idle: consolidate idle functions and definitions
s390/nohz: use a per-cpu flag for arch_needs_cpu
s390/vtime: do not reset idle data on CPU hotplug
s390/dasd: add support for control unit initiated reconfiguration
s390/dasd: fix infinite loop during format
s390/mm: make use of ipte range facility
s390/setup: correct 4-level kernel page table detection
s390/topology: call set_sched_topology early
s390/uprobes: architecture backend for uprobes
s390/uprobes: common library for kprobes and uprobes
s390/rwlock: use the interlocked-access facility 1 instructions
s390/rwlock: improve writer fairness
s390/rwlock: remove interrupt-enabling rwlock variant.
s390/mm: remove change bit override support
...
Pull x86 seccomp changes from Ingo Molnar:
"This tree includes x86 seccomp filter speedups and related preparatory
work, which touches core seccomp facilities as well.
The main idea is to split seccomp into two phases, to be able to enter
a simple fast path for syscalls with ptrace side effects.
There's no substantial user-visible (and ABI) effects expected from
this, except a change in how we emit a better audit record for
SECCOMP_RET_TRACE events"
* 'x86-seccomp-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86_64, entry: Use split-phase syscall_trace_enter for 64-bit syscalls
x86_64, entry: Treat regs->ax the same in fastpath and slowpath syscalls
x86: Split syscall_trace_enter into two phases
x86, entry: Only call user_exit if TIF_NOHZ
x86, x32, audit: Fix x32's AUDIT_ARCH wrt audit
seccomp: Document two-phase seccomp and arch-provided seccomp_data
seccomp: Allow arch code to provide seccomp_data
seccomp: Refactor the filter callback and the API
seccomp,x86,arm,mips,s390: Remove nr parameter from secure_computing
Pull scheduler updates from Ingo Molnar:
"The main changes in this cycle were:
- Optimized support for Intel "Cluster-on-Die" (CoD) topologies (Dave
Hansen)
- Various sched/idle refinements for better idle handling (Nicolas
Pitre, Daniel Lezcano, Chuansheng Liu, Vincent Guittot)
- sched/numa updates and optimizations (Rik van Riel)
- sysbench speedup (Vincent Guittot)
- capacity calculation cleanups/refactoring (Vincent Guittot)
- Various cleanups to thread group iteration (Oleg Nesterov)
- Double-rq-lock removal optimization and various refactorings
(Kirill Tkhai)
- various sched/deadline fixes
... and lots of other changes"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (72 commits)
sched/dl: Use dl_bw_of() under rcu_read_lock_sched()
sched/fair: Delete resched_cpu() from idle_balance()
sched, time: Fix build error with 64 bit cputime_t on 32 bit systems
sched: Improve sysbench performance by fixing spurious active migration
sched/x86: Fix up typo in topology detection
x86, sched: Add new topology for multi-NUMA-node CPUs
sched/rt: Use resched_curr() in task_tick_rt()
sched: Use rq->rd in sched_setaffinity() under RCU read lock
sched: cleanup: Rename 'out_unlock' to 'out_free_new_mask'
sched: Use dl_bw_of() under RCU read lock
sched/fair: Remove duplicate code from can_migrate_task()
sched, mips, ia64: Remove __ARCH_WANT_UNLOCKED_CTXSW
sched: print_rq(): Don't use tasklist_lock
sched: normalize_rt_tasks(): Don't use _irqsave for tasklist_lock, use task_rq_lock()
sched: Fix the task-group check in tg_has_rt_tasks()
sched/fair: Leverage the idle state info when choosing the "idlest" cpu
sched: Let the scheduler see CPU idle states
sched/deadline: Fix inter- exclusive cpusets migrations
sched/deadline: Clear dl_entity params when setscheduling to different class
sched/numa: Kill the wrong/dead TASK_DEAD check in task_numa_fault()
...
Pull dma-mapping update from Marek Szyprowski:
"Provide the dma write coherent api (available previously on ARM
architecture) for all other architectures, which use dma_ops-based dma
mapping implementation.
This lets one to use the same code in the device drivers regardless of
the selected architecture"
* 'for-v3.18' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
dma-mapping: Provide write-combine allocations
s390: Implement dma_{alloc,free}_attrs()
The different architectures used their own (and different) declarations:
extern __visible const void __nosave_begin, __nosave_end;
extern const void __nosave_begin, __nosave_end;
extern long __nosave_begin, __nosave_end;
Consolidate them using the first variant in <asm/sections.h>.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull timer fixes from Ingo Molnar:
"Main changes:
- Fix the deadlock reported by Dave Jones et al
- Clean up and fix nohz_full interaction with arch abilities
- nohz init code consolidation/cleanup"
* 'timers-nohz-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
nohz: nohz full depends on irq work self IPI support
nohz: Consolidate nohz full init code
arm64: Tell irq work about self IPI support
arm: Tell irq work about self IPI support
x86: Tell irq work about self IPI support
irq_work: Force raised irq work to run on irq work interrupt
irq_work: Introduce arch_irq_work_has_interrupt()
nohz: Move nohz full init call to tick init
We can simply patch the mask field within the branch relative on
condition instruction at the beginning of the ftrace_graph_caller
code block.
This makes the logic even simpler and we get rid of the displacement
calculation.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
31 bit and 64 bit diverge more and more and it is rather painful
to keep both parts running.
To make things simpler just remove the 31 bit support which nobody
uses anyway.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
With this patch for kdump the s390 vector registers are stored into the
prepared save areas in the old kernel and into the REGSET_VX_LOW and
REGSET_VX_HIGH ELF notes for /proc/vmcore in the new kernel.
The NT_S390_VXRS_LOW note contains the lower halves of the first 16 vector
registers 0-15. The higher halves are stored in the floating point register
ELF note. The NT_S390_VXRS_HIGH contains the full vector registers 16-31.
The kernel provides a save area for storing vector register in case of
machine checks. A pointer to this save are is stored in the CPU lowcore
at offset 0x11b0. This save area is also used to save the registers for
kdump. In case of a dumped crashed kdump those areas are used to extract
the registers of the production system.
The vector registers for remote CPUs are stored using the "store additional
status at address" SIGP. For the dump CPU the vector registers are stored
with the VSTM instruction.
With this patch also zfcpdump stores the vector registers.
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The vector extension introduces 32 128-bit vector registers and a set of
instruction to operate on the vector registers.
The kernel can control the use of vector registers for the problem state
program with a bit in control register 0. Once enabled for a process the
kernel needs to retain the content of the vector registers on context
switch. The signal frame is extended to include the vector registers.
Two new register sets NT_S390_VXRS_LOW and NT_S390_VXRS_HIGH are added
to the regset interface for the debugger and core dumps.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move the C functions and definitions related to the idle state handling
to arch/s390/include/asm/idle.h and arch/s390/kernel/idle.c. The function
s390_get_idle_time is renamed to arch_cpu_idle_time and vtime_stop_cpu to
enabled_wait.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move the nohz_delay bit from the s390_idle data structure to the
per-cpu flags. Clear the nohz delay flag in __cpu_disable and
remove the cpu hotplug notifier that used to do this.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The sysfs attributes /sys/devices/system/cpu/cpu0/idle_count and
/sys/devices/system/cpu/cpu0/idle_time_us are reset to zero every
time a CPU is set online. The idle and iowait fields in /proc/stat
corresponding to idle_time_us are not reset. To make things
consistent do not reset the data for the sys attributes.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull networking updates from David Miller:
"Most notable changes in here:
1) By far the biggest accomplishment, thanks to a large range of
contributors, is the addition of multi-send for transmit. This is
the result of discussions back in Chicago, and the hard work of
several individuals.
Now, when the ->ndo_start_xmit() method of a driver sees
skb->xmit_more as true, it can choose to defer the doorbell
telling the driver to start processing the new TX queue entires.
skb->xmit_more means that the generic networking is guaranteed to
call the driver immediately with another SKB to send.
There is logic added to the qdisc layer to dequeue multiple
packets at a time, and the handling mis-predicted offloads in
software is now done with no locks held.
Finally, pktgen is extended to have a "burst" parameter that can
be used to test a multi-send implementation.
Several drivers have xmit_more support: i40e, igb, ixgbe, mlx4,
virtio_net
Adding support is almost trivial, so export more drivers to
support this optimization soon.
I want to thank, in no particular or implied order, Jesper
Dangaard Brouer, Eric Dumazet, Alexander Duyck, Tom Herbert, Jamal
Hadi Salim, John Fastabend, Florian Westphal, Daniel Borkmann,
David Tat, Hannes Frederic Sowa, and Rusty Russell.
2) PTP and timestamping support in bnx2x, from Michal Kalderon.
3) Allow adjusting the rx_copybreak threshold for a driver via
ethtool, and add rx_copybreak support to enic driver. From
Govindarajulu Varadarajan.
4) Significant enhancements to the generic PHY layer and the bcm7xxx
driver in particular (EEE support, auto power down, etc.) from
Florian Fainelli.
5) Allow raw buffers to be used for flow dissection, allowing drivers
to determine the optimal "linear pull" size for devices that DMA
into pools of pages. The objective is to get exactly the
necessary amount of headers into the linear SKB area pre-pulled,
but no more. The new interface drivers use is eth_get_headlen().
From WANG Cong, with driver conversions (several had their own
by-hand duplicated implementations) by Alexander Duyck and Eric
Dumazet.
6) Support checksumming more smoothly and efficiently for
encapsulations, and add "foo over UDP" facility. From Tom
Herbert.
7) Add Broadcom SF2 switch driver to DSA layer, from Florian
Fainelli.
8) eBPF now can load programs via a system call and has an extensive
testsuite. Alexei Starovoitov and Daniel Borkmann.
9) Major overhaul of the packet scheduler to use RCU in several major
areas such as the classifiers and rate estimators. From John
Fastabend.
10) Add driver for Intel FM10000 Ethernet Switch, from Alexander
Duyck.
11) Rearrange TCP_SKB_CB() to reduce cache line misses, from Eric
Dumazet.
12) Add Datacenter TCP congestion control algorithm support, From
Florian Westphal.
13) Reorganize sk_buff so that __copy_skb_header() is significantly
faster. From Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1558 commits)
netlabel: directly return netlbl_unlabel_genl_init()
net: add netdev_txq_bql_{enqueue, complete}_prefetchw() helpers
net: description of dma_cookie cause make xmldocs warning
cxgb4: clean up a type issue
cxgb4: potential shift wrapping bug
i40e: skb->xmit_more support
net: fs_enet: Add NAPI TX
net: fs_enet: Remove non NAPI RX
r8169:add support for RTL8168EP
net_sched: copy exts->type in tcf_exts_change()
wimax: convert printk to pr_foo()
af_unix: remove 0 assignment on static
ipv6: Do not warn for informational ICMP messages, regardless of type.
Update Intel Ethernet Driver maintainers list
bridge: Save frag_max_size between PRE_ROUTING and POST_ROUTING
tipc: fix bug in multicast congestion handling
net: better IFF_XMIT_DST_RELEASE support
net/mlx4_en: remove NETDEV_TX_BUSY
3c59x: fix bad split of cpu_to_le32(pci_map_single())
net: bcmgenet: fix Tx ring priority programming
...
Apart from the usual cleanups, here is the summary of new features:
- s390 moves closer towards host large page support
- PowerPC has improved support for debugging (both inside the guest and
via gdbstub) and support for e6500 processors
- ARM/ARM64 support read-only memory (which is necessary to put firmware
in emulated NOR flash)
- x86 has the usual emulator fixes and nested virtualization improvements
(including improved Windows support on Intel and Jailhouse hypervisor
support on AMD), adaptive PLE which helps overcommitting of huge guests.
Also included are some patches that make KVM more friendly to memory
hot-unplug, and fixes for rare caching bugs.
Two patches have trivial mm/ parts that were acked by Rik and Andrew.
Note: I will soon switch to a subkey for signing purposes. To verify
future signed pull requests from me, please update my key with
"gpg --recv-keys 9B4D86F2". You should see 3 new subkeys---the
one for signing will be a 2048-bit RSA key, 4E6B09D7.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=iEVi
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"Fixes and features for 3.18.
Apart from the usual cleanups, here is the summary of new features:
- s390 moves closer towards host large page support
- PowerPC has improved support for debugging (both inside the guest
and via gdbstub) and support for e6500 processors
- ARM/ARM64 support read-only memory (which is necessary to put
firmware in emulated NOR flash)
- x86 has the usual emulator fixes and nested virtualization
improvements (including improved Windows support on Intel and
Jailhouse hypervisor support on AMD), adaptive PLE which helps
overcommitting of huge guests. Also included are some patches that
make KVM more friendly to memory hot-unplug, and fixes for rare
caching bugs.
Two patches have trivial mm/ parts that were acked by Rik and Andrew.
Note: I will soon switch to a subkey for signing purposes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (157 commits)
kvm: do not handle APIC access page if in-kernel irqchip is not in use
KVM: s390: count vcpu wakeups in stat.halt_wakeup
KVM: s390/facilities: allow TOD-CLOCK steering facility bit
KVM: PPC: BOOK3S: HV: CMA: Reserve cma region only in hypervisor mode
arm/arm64: KVM: Report correct FSC for unsupported fault types
arm/arm64: KVM: Fix VTTBR_BADDR_MASK and pgd alloc
kvm: Fix kvm_get_page_retry_io __gup retval check
arm/arm64: KVM: Fix set_clear_sgi_pend_reg offset
kvm: x86: Unpin and remove kvm_arch->apic_access_page
kvm: vmx: Implement set_apic_access_page_addr
kvm: x86: Add request bit to reload APIC access page address
kvm: Add arch specific mmu notifier for page invalidation
kvm: Rename make_all_cpus_request() to kvm_make_all_cpus_request() and make it non-static
kvm: Fix page ageing bugs
kvm/x86/mmu: Pass gfn and level to rmapp callback.
x86: kvm: use alternatives for VMCALL vs. VMMCALL if kernel text is read-only
kvm: x86: use macros to compute bank MSRs
KVM: x86: Remove debug assertion of non-PAE reserved bits
kvm: don't take vcpu mutex for obviously invalid vcpu ioctls
kvm: Faults which trigger IO release the mmap_sem
...
On 32 bit systems cmpxchg cannot handle 64 bit values, so
some additional magic is required to allow a 32 bit system
with CONFIG_VIRT_CPU_ACCOUNTING_GEN=y enabled to build.
Make sure the correct cmpxchg function is used when doing
an atomic swap of a cputime_t.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rik van Riel <riel@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: umgwanakikbuti@gmail.com
Cc: fweisbec@gmail.com
Cc: srao@redhat.com
Cc: lwoodman@redhat.com
Cc: atheurer@redhat.com
Cc: oleg@redhat.com
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linux390@de.ibm.com
Cc: linux-arch@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-s390@vger.kernel.org
Link: http://lkml.kernel.org/r/20140930155947.070cdb1f@annuminas.surriel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch introduces the halt_wakeup counter used by common code and uses it to
count vcpu wakeups done in s390 arch specific code.
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
There is nothing to do for KVM to support TOD-CLOCK steering.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Invalidate several pte entries at once if the ipte range facility
is available. Currently this works only for DEBUG_PAGE_ALLOC where
several up to 2 ^ MAX_ORDER may be invalidated at once.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix calculation to decide if a 4-level kernel page table is required.
Git commit c972cc60c2 "s390/vmalloc: have separate modules area"
added the separate module area which reduces the size of the vmalloc
area but fails to take it into account for the 3 vs 4 level page table
decision.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The call to topology_init is too late for the set_sched_topology call.
The initial scheduling domain structure has already been established
with default topology array. Use the smp_cpus_done() call to get the
s390 specific topology array registered early enough.
Cc: stable@vger.kernel.org # v3.16+
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch moves common functions from kprobes.c to probes.c.
Thus its possible for uprobes to use them without enabling kprobes.
Signed-off-by: Jan Willeke <willeke@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make use of the load-and-add, load-and-or and load-and-and instructions
to atomically update the read-write lock without a compare-and-swap loop.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Set the write-lock bit in the out-of-line rwlock code to indicate that
a writer is waiting. Additional readers will no be able to get the lock
until at least one writer got the lock. Additional writers have to wait
for the first writer to release the lock again.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the vmemmap array gets filled with large pages we allocate those
pages with vmemmap_alloc_block(), which returns cleared pages.
Only for single 4k pages we call our own vmem_alloc_pages() which does
not return cleared pages. However we can also call vmemmap_alloc_block()
to allocate the 4k pages.
This way we can also make sure the vmemmap array is cleared after its
population.
Therefore we can remove the memset at the end of the function which
would clear the vmmemmap array a second time on machines which do
support EDAT1.
On very large configurations this can save us several seconds.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The architecture suggests to use address 0 as parameter for stfl,
to allow for future extensions. Using __LC_STFL_FAC_LIST (0x200)
shows which address is used, but might be not future proof.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add an owner field to the arch_rwlock_t to be able to pass the timeslice
of a virtual CPU with diagnose 0x9c to the lock owner in case the rwlock
is write-locked. The undirected yield in case the rwlock is acquired
writable but the lock is read-locked is removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This device driver allows accessing a HMC drive CD/DVD-ROM.
It can be used in a LPAR and z/VM environment.
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reviewed-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Ralf Hoppe <rhoppe@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Jason J. Herne