Commit Graph

24609 Commits

Author SHA1 Message Date
Wey-Yi Guy aa833c4b1a iwlwifi: split the drivers for agn and legacy devices 3945/4965
Intel WiFi devices 3945 and 4965 now have their own driver in the folder

	drivers/net/wireless/iwlegacy

Add support to build these drivers independently of the driver for
AGN devices. Selecting the 3945 builds iwl3945.ko and iwl_legacy.ko,
and selecting the 4965 builds iwl4965.ko and iwl_legacy.ko. iwl-legacy.ko
contains code shared between both devices.

The 3945 is an ABG/BG device, with no support for 802.11n. The 4965 is a 2x3
ABGN device.

Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Acked-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-02-21 10:57:10 -08:00
Wey-Yi Guy 73b78a2272 iwlwifi: enable 2-wire bt coex support for non-combo device
For non-combo devices, 2-wire BT coex is needed to make sure BT coex
still function with external BT devices

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-02-21 10:09:16 -08:00
Wey-Yi Guy 46d0637a12 iwlwifi: Loading correct uCode again when fail to load
During uCode loading, if the reply_alive come back with "failure",
try to load the same uCode again.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-02-21 10:08:38 -08:00
Wey-Yi Guy 491bc29276 iwlwifi: Limit number of firmware reload
If device has serious problem and cause firmware can not recover itself.
Keep reloading firmware will not help, it can only fill up the syslog and
lock up the system because busy reloading.

Introduce the limit reload counter, if the reload reach the maximum within
the pre-defined duration;stop the reload operation.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-02-21 10:08:15 -08:00
John W. Linville b67afe7f43 Merge ssh://master.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
Conflicts:
	drivers/bluetooth/ath3k.c
	drivers/bluetooth/btusb.c
2011-02-18 17:03:41 -05:00
Vivek Natarajan 1a63e2ce4e ath9k_hw: Updates for AR9485 1.1 chipsets.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-18 16:54:57 -05:00
Vivek Natarajan 8354dd3ebc ath9k_htc: Fix a compilation warning.
Initialize caldata to avoid compilation warning.

CC [M]  drivers/net/wireless/ath/ath9k/htc_drv_main.o
drivers/net/wireless/ath/ath9k/htc_drv_main.c: In function ‘ath9k_htc_config’:
drivers/net/wireless/ath/ath9k/htc_drv_main.c:172: warning: ‘caldata’ may be used uninitialized in this function
drivers/net/wireless/ath/ath9k/htc_drv_main.c:172: note: ‘caldata’ was declared here

Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-18 16:54:56 -05:00
Christian Lamparter 0d4171e215 p54: implement flush callback
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-18 16:54:54 -05:00
Larry Finger fe0b7c616e p54: Fix compile warning
If any of the p54-based drivers are built with CONFIG_P54_LEDS not
defined, the following warning is generated:

  CC [M]  drivers/net/wireless/p54/main.o
drivers/net/wireless/p54/main.c: In function ‘p54_register_common’:
drivers/net/wireless/p54/main.c:614:21: warning: unused variable ‘priv’

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-18 16:53:20 -05:00
Bob Copeland 12873372fe ath5k: move external function definitions to a header file
Johannes pointed out the mess of external function prototypes in the
mac80211-ops.c file.  Woe to anyone who changes these functions...

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-18 16:53:20 -05:00
Nikolay Ledovskikh 28bec7b845 ath5k: Correct channel setting for AR2317 chip
Correct channel setting function must be used for AR2317.
When I tested ahb patch on bullet2 all seemed to work fine,
but it couldn't connect another host (using ibss for example).
During an analysis I observed that it's transmitting on another
channel. I looked into madwifi code and understood that
the problem is in channel setting function. So atheros RF2317 not
fully handled in the current ath5k version and must be patched.

Signed-off-by: Nikolay Ledovskikh <nledovskikh@gmail.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-18 16:47:37 -05:00
Xose Vazquez Perez 00781a74ee wireless: rt2x00: rt2800pci.c: add two ids
taken two RT35XX EDIMAX from DPO_RT3562_3592_3062_LinuxSTA_V2.4.1.1_20101217

Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-18 16:47:37 -05:00
Mohammed Shafi Shajakhan 0f5cd45960 ath9k: Fix ath9k prevents CPU to enter C3 states
The DMA latency issue is observed only in Intel pinetrail platforms
but in the driver we had a default PM-QOS value of 55. This caused
unnecessary power consumption and battery drain in other platforms.

Remove the pm-qos thing in the driver code and address the throughput
issue in Intel pinetrail platfroms in user space using any one of
the scripts in below links:

http://www.kernel.org/pub/linux/kernel/people/mcgrof/scripts/cpudmalatency.c
http://johannes.sipsolutions.net/files/netlatency.c.txt

More details can be found in the following bugzilla link:

https://bugzilla.kernel.org/show_bug.cgi?id=27532

This reverts the following commits:

	98c316e348
	4dc3530df7
	10598c124e

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-15 11:16:00 -05:00
Christian Lamparter 05e051d8ae p54spi: update sample eeprom
Commit: "p54: enhance rssi->dBm database import"
changed the way how the driver deals with the
rssical data. A new data format was necessary
and hence this patch.

NOTE: (for users with a custom eeprom binary)
I spent some time updating p54tools to support
the new format too: => (git available from)
http://git.kernel.org/?p=linux/kernel/git/chr/p54tools.git

It now comes with a simplistic script "n800_rssi2v2.sh"
which can be used to automate the conversion.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-14 15:52:10 -05:00
Christian Lamparter 7a047f4f2f p54: enhance rssi->dBm database import
This patch fixes several shortcomings of the
previous implementation. Features of the
rewrite include:

 * handles undocumented "0x0000" word at the
   start of the frequency table.
   (Affected some early? DELL 1450 USB devices
    and my Symbol 5GHz miniPCI card.)

 * supports more than just one reference point
   per band. (Also needed for the Symbol card.)

 * ships with default values in case the eeprom
   data is damaged, absent or unsupported.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-14 15:52:10 -05:00
Christian Lamparter a3162eed04 p54: p54_generate_band cleanup
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-14 15:51:21 -05:00
Christian Lamparter 192abece75 p54: sort channel list by frequency instead of channel index
Some channel indices of the low 5GHz band clash with
those of the 2.4GHz band. Therefore we should go
with the channel's center frequency.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-14 15:51:21 -05:00
Jussi Kivilinna 91f71fa5da zd1211rw: add unlikely to ZD_ASSERT
Case assert is violated should be quite unlikely.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-14 15:51:21 -05:00
Jussi Kivilinna 8662b2518f zd1211rw: move async iowrite16v up to callers
Writing beacon to device happen through multiple write command calls.
zd_usb_iowrite16v uses synchronous urb call and with multiple write
commands in row causes high CPU usage.

Make asynchronous zd_usb_iowrite16v_async available outside zd_usb.c
and use where possible.

This lower CPU usage from ~10% to ~2% on Intel Atom when running
AP-mode with 100 TU beacon interval.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-14 15:51:21 -05:00
Jussi Kivilinna eefdbec1ea zd1211rw: use async urb for write command
Writing beacon to device happen through multiple write command calls.
zd_usb_iowrite16v uses synchronous urb call and with multiple write
commands in row causes high CPU usage.

This patch makes zd_usb_iowrite16v use asynchronous urb submit within
zd_usb.c. zd_usb_iowrite16v_async_start is used to initiate writing
multiple commands to device using zd_usb_iowrite16v_async. Each URB
is delayed and submitted to device by next zd_usb_iowrite16v_async
call or by call to zd_usb_iowrite16v_async_end. URBs submitted by
zd_usb_iowrite16v_async have URB_NO_INTERRUPT set and last URB
send by zd_usb_iowrite16v_async_end does not. This lower CPU
usage when doing writes that require multiple URBs.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-14 15:51:21 -05:00
Jussi Kivilinna 37939810b9 zd1211rw: correct use of usb_bulk_msg on interrupt endpoints
zd1211rw is using usb_bulk_msg() with usb_sndbulkpipe() on interrupt endpoint.
However usb_bulk_msg() internally corrects this and makes interrupt URB.

It's better to change usb_bulk_msgs in zd1211rw to usb_interrupt_msg for less
confusion.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-14 15:51:21 -05:00
Rajkumar Manoharan 014cf3bb1e ath9k: disable beaconing before stopping beacon queue
Beaconing should be disabled before stopping beacon queue.
Not doing so could queue up beacons in hw that causes
failure to stop Tx DMA, due to pending frames in hw
and also unnecessary beacon tasklet schedule.

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-14 15:51:20 -05:00
Seth Forshee d76dfc612b rt2x00: Check for errors from skb_pad() calls
Commit 739fd94 ("rt2x00: Pad beacon to multiple of 32 bits")
added calls to skb_pad() without checking the return value,
which could cause problems if any of those calls does happen
to fail. Add checks to prevent this from happening.

Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-14 15:50:17 -05:00
Larry Finger a3dc5e881a rtlwifi: rtl8192ce: Rework rtl8192ce/phy.c
Make the phy.c codes for rtl8192ce and rtl8192cu be as alike as possible.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-11 16:16:38 -05:00
Larry Finger 25b2bc3086 rtlwifi: rtl8192ce: Refactor rtl8192ce/fw
Make rtlwifi/rtl8192ce/fw.{h,c} match what will be needed for
rtlwifi/rtl8192cu.{h,c}.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-11 16:16:38 -05:00
Larry Finger 8c96fcf721 rtlwifi: rtl8192ce: Refactor rtl8192ce/dm
To reuse as much code as possible when adding additional drivers to the
rtlwifi tree, the common parts of various routines are moved to
drivers/net/wireless/rtlwifi. This patch does that for the version of
dm.{h,c} used by rtl8192ce.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-11 16:16:38 -05:00
George 2ca20f79e0 rtlwifi: Add usb driver
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: George <george0505@realtek.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-11 16:16:37 -05:00
Larry Finger 62e63975f4 rtlwifi: Modify core routines
The rtlwifi core needs some changes before inclusion of a driver
for the RTL8192CU USB device.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: <chaoming_li@realsil.com.cn>
Signed-off-by: <george0505@realtek.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-11 16:16:37 -05:00
Wey-Yi Guy caebbb7a4a iwlagn: handle bt defer work in 2000 series
For 2000 series, need to handle bt traffic changes when
receive notification from uCode

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-02-11 11:51:57 -08:00
Wey-Yi Guy c4197c6298 iwlagn: donot process bt update when bt coex disable
If bt coex is disabled, do not process any bt related information
from uCode even received.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-02-11 11:51:49 -08:00
Stanislaw Gruszka 67acad5fe5 iwlwifi: fix ack health for WiFi/BT combo devices
Combo devices have TX statistics on different place, because
struct statistics_rx_bt and struct statistics_rx have different
size. User proper values on combo devices instead of random data.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-09 16:09:50 -05:00
Stanislaw Gruszka f266526da4 iwlwifi: cleanup iwl_good_ack_health
Make ack health code easies to read. Compared to previous
code, we do not print debug messages when expected_ack_cnt_delta == 0
and also do check against negative deltas.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-09 16:09:49 -05:00
Stanislaw Gruszka ca3d938964 iwlwifi: cleanup iwl_recover_from_statistics
No functional change, make recover from statistics code
easies to read.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-09 16:09:49 -05:00
Steve Brown 9814f6b34b ath9k: Remove redundant beacon_interval
The variable appears in both ath_softc and ath_beacon_config.
The struct ath_beacon_config is embedded in ath_softc. The redundant
variable was added by commit id 57c4d7b4c4.

Signed-off-by: Steve Brown <sbrown@cortland.com>
Reviewed-by: Mohammed Shafi <shafi.ath9k@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-09 16:09:48 -05:00
Ben Greear 603b3eefb9 ath9k: Add debug info for configuring power level.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-09 16:09:47 -05:00
Ben Greear 8c79a61095 ath9k: Print channel-type in chan-change dbg message.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-09 16:09:44 -05:00
Stanislaw Gruszka c91d01556f iwl3945: remove plcp check
Patch fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=654599

Many users report very low speed problem on 3945 devices,
this patch fixes problem, but only for some of them.

For unknown reason, sometimes after hw scanning, device is not able
to receive frames at high rate. Since plcp health check may request
hw scan to "reset radio", performance problem start to be observable
after update kernel to .35, where plcp check was introduced.

Bug reporter confirmed that removing plcp check fixed problem for him.

Reported-and-tested-by: SilvioTO <silviotoya@yahoo.it>
Cc: stable@kernel.org  # 2.6.35+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-09 15:35:12 -05:00
Eliad Peller 72c2d9e511 wl12xx: set supported_rates after association
Instead of looking for supported_rates change on every tx packet,
just extract the supported_rates after association completes (station only).

Remove wl1271.sta_rate_set and WL1271_FLAG_STA_RATES_CHANGED which are
not used anymore.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-02-08 22:51:42 -02:00
Eliad Peller fe5ef09066 wl12xx: use the conf struct instead of macros for memory configuration
make the configuration management more flexible by using the
conf struct, rather than predefined macros.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-02-08 22:51:42 -02:00
Eliad Peller c8bde24342 wl12xx: move to new firmware (6.1.3.50.49)
This patch adds support for the new wl12xx firmware (Rev 6.1.3.50.49)

Since this fw is not backward compatible with previous fw versions,
a new fw (with different name) is being fetched.

(the patch is big because it contains all the required fw api changes.
splitting it into multiple patches will result in corrupted intermediate
commits)

Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-02-08 22:51:42 -02:00
Eliad Peller ee60833a4f wl12xx: mcp2.5 - add config_ps acx
mcp2.5 uses this acx to configure the fw only once, rather than
passing the params in every enter psm command.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-02-08 22:51:42 -02:00
Mohammed Shafi Shajakhan 3a2329f268 ath9k: Update comments for not parsing DTIM period
Add few comments for not parsing DTIM period from mac80211

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-07 16:18:28 -05:00
Nick Kossifidis c210de8f88 ath5k: Fix fast channel switching
Fast channel change fixes:

a) Always set OFDM timings
b) Don't re-activate PHY
c) Enable only NF calibration, not AGC

Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-07 16:18:27 -05:00
Don Fry 3dd823e6b8 iwlagn: Re-enable RF_KILL interrupt when down
With commit 554d1d027b only one RF_KILL
interrupt will be seen by the driver when the interface is down.

Re-enable the interrupt when it occurs to see all transitions.

Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-07 16:02:14 -05:00
Wey-Yi Guy 80b38fffab iwlwifi: fix compiling error with different configuration
When .config has different configuration, it might fail to compile
iwlwifi. fix it

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-02-06 09:31:00 -08:00
Johannes Berg 2f115cf24e iwlwifi: remove unnecessary locking
This code, and the places that set the variable
is_internal_short_scan and the vif pointers are
all protected by the mutex, there's no point in
locking the spinlock here as well (any more).

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-02-06 09:30:54 -08:00
Felix Fietkau cb8d61de2d ath9k: add additional checks for the baseband hang detection
Since even with the latest changes the false positive issue of the baseband
hang check is not fully solved yet, additional checks are needed.
If the baseband hang occurs, the rx_clear signal will be stuck to high, so
we can use the cycle counters to confirm it.
With this patch, a hardware reset is only triggered if the baseband hang
check returned true three times in a row, with a beacon interval between
each check and if the busy time was also 99% or more during the check
intervals.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:52 -05:00
Jouni Malinen 8e5461041f ath: Fix clearing of secondary key cache entry for TKIP
All register writes to the key cache have to be done in pairs. However,
the clearing of a separate MIC entry with hardware revisions that use
combined MIC key layout did not do that with one of the registers. Add
the matching register write to the following register to make the KEY4
register write actually complete.

This is mostly a fix for a theoretical issue since the incorrect entry
that could potentially be left behind in the key cache would not match
with received frames. Anyway, better make this code clean the entry
correctly using paired register writes.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:52 -05:00
Jussi Kivilinna 24d24c627c zd1211rw: add useful debug output
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:51 -05:00
Jussi Kivilinna ab419e9bda zd1211rw: enable NL80211_IFTYPE_AP
It should be safe to enable AP-mode now.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:51 -05:00
Jussi Kivilinna 1f6cccccea zd1211rw: reset rx urbs after idle period of 30 seconds
RX appears to freeze while idle. Resetting rx-urbs appears to be enough to fix
this. Do reset 30 seconds after last rx.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:51 -05:00
Jussi Kivilinna 3985a46543 zd1211rw: reset device when CR_BCN_FIFO_SEMAPHORE freezes in beacon setup
When driver fails to acquire device semaphore lock, device usually
freezes soon afterwards. So failing to acquire lock indicates us that
not everything is going right in device/fw. So reset device when
this happens.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:51 -05:00
Jussi Kivilinna a0fd751f09 zd1211rw: add TX watchdog and device resetting
When doing transfers at high speed for long time, tx queue can freeze. So add
tx watchdog. TX-watchdog checks for locked tx-urbs and reset hardware when
such is detected. Merely unlinking urb was not enough, device have to be
reseted. Hw settings are restored so that any open link will stay on after
reset.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:51 -05:00
Jussi Kivilinna 212e1a5b9d zd1211rw: collect driver settings and add function to restore theim
We need HW hard reset later in patchset to reset device after TX-stall.
Collect all settings that we have set to driver for later reset and
add restore function.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:50 -05:00
Jussi Kivilinna 8f2d8f869a zd1211rw: lower hw command timeouts
Device command timeouts are set up very high (1 sec) and this causes
AP beacon to lock up for long for example. Checking timeouts on device
it's easy to see that 1 sec timeout is not needed, when device fails
to response longer timeout doesn't help:

[  473.074419] zd1211rw 1-1:1.0: print_times() Read times:
[  473.175163] zd1211rw 1-1:1.0: print_time()     0 - 10 msec: 1506
[  473.176429] zd1211rw 1-1:1.0: print_time()    11 - 50 msec: 0
[  473.177955] zd1211rw 1-1:1.0: print_time()   51 - 100 msec: 0
[  473.180703] zd1211rw 1-1:1.0: print_time()  101 - 250 msec: 0
[  473.182101] zd1211rw 1-1:1.0: print_time()  251 - 500 msec: 0
[  473.183221] zd1211rw 1-1:1.0: print_time() 500 - 1000 msec: 20
[  473.184381] zd1211rw 1-1:1.0: print_time() 1000 - ... msec: 18

Also vendor driver doesn't use this long timeout. Therefore change
timeout to 50msec.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:50 -05:00
Jussi Kivilinna 4a3b0874a4 zd1211rw: change interrupt URB buffer to DMA buffer
As might lower beacon update CPU usage.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:50 -05:00
Jussi Kivilinna 9bca0c3b54 zd1211rw: use stack and preallocated memory for small cmd-buffers
Use stack for allocing small < 64 byte arrays in zd_chip.c and preallocated
buffer in zd_usb.c. This might lower CPU usage for beacon setup.

v2:
 - Do not use stack buffers in zd_usb.c as they would be used for urb
   transfer_buffer.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:50 -05:00
Jussi Kivilinna 5127229292 zd1211rw: batch beacon config commands together
Beacon config function writes beacon to hw one write per byte. This is very
slow (usually taking more than 100ms to finish) and causes high CPU usage
when in AP-mode (kworker at ~50% on Intel Atom N270). By batching commands
together zd_mac_config_beacon() runtime can be lowered to 1/5th and lower
CPU usage to saner levels (<10% on Atom).

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:50 -05:00
Jussi Kivilinna 9be2325636 zd1211rw: add beacon watchdog and setting HW beacon more failsafe
When doing tx/rx at high packet rate (for example simply using ping -f),
device starts to fail to respond to control messages. On non-AP modes
this only causes problems for LED updating code but when we are running
in AP-mode we are writing new beacon to HW usually every 100ms. Now if
control message fails in HW beacon setup, device lock is kept locked
and beacon data partially written. This can and usually does cause:

 1. HW beacon setup fail now on, as driver cannot acquire device lock.
 2. Beacon-done interrupt stop working as device has incomplete beacon.

Therefore make zd_mac_config_beacon() always try to release device lock
and add beacon watchdog to restart beaconing when stall is detected.

Also fix zd_mac_config_beacon() try acquiring device lock for max 500ms,
as what old code appeared to be trying to do using loop and msleep(1).

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:50 -05:00
Jussi Kivilinna 4099e2f440 zd1211rw: implement beacon fetching and handling ieee80211_get_buffered_bc()
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:49 -05:00
Jussi Kivilinna b91a515dbb zd1211rw: let zd_set_beacon_interval() set dtim_period and add AP-beacon flag
Add support for AP-mode beacon. Also disable beacon when interface is set
down as otherwise hw will keep flooding NEXT_BCN interrupts.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:49 -05:00
Jussi Kivilinna f773e409b9 zd1211rw: fix ack_pending in filter_ack causing tx-packet ordering problem on monitor
For reasons not very clear yet to me, filter_ack leaves matching tx-packet
pending with 'ack_pending'. This causes tx-packet to be passed back to upper
layer after next packet has been transfered and tx-packets might end up
coming come out of monitor interface in wrong order vs. rx.

Because of this when enable AP-mode, hostapd monitor interface would get
packets in wrong order causing problems in WPA association.

So don't use mac->ack_pending when in AP-mode.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:49 -05:00
Jussi Kivilinna c2fadcb3b1 zd1211rw: support setting BSSID for AP mode
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:49 -05:00
Jussi Kivilinna 5cf6cf819b zd1211rw: move set_rts_cts_work to bss_info_changed
As bss_info_changed may sleep, we can as well set RTS_CTS register right away.
Keep mac->short_preamble for later use (hw reset).

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:49 -05:00
Jussi Kivilinna a6fb071bbf zd1211rw: move set_multicast_hash and set_rx_filter from workers to configure_filter
Workers not needed anymore since configure_filter may sleep. Keep
mac->multicast_hash for later use (hw reset).

Signed-off-by: Jussi Kivilinna <jussi.kivilina@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:49 -05:00
Jussi Kivilinna 88a1159a37 zd1211rw: fix beacon interval setup
Vendor driver uses CR_BNC_INTERVAL at various places, one is HW_EnableBeacon()
that combinies beacon interval with BSS-type flag and DTIM value in upper 16bit
of u32. The other one is HW_UpdateBcnInterval() that set_aw_pt_bi()
appears to be based on. HW_UpdateBcnInterval() takes interval argument as u16
and uses that for calculations, set_aw_pt_bi() uses u32 value that has flags
and dtim in upper part. This clearly seems wrong. Also HW_UpdateBcnInterval()
updates only lower 16bit part of CR_BNC_INTERVAL. So make set_aw_pt_bi() do
calculations on only lower u16 part of s->beacon_interval.

Also set 32bit beacon interval register before reading values from device,
as HW_EnableBeacon() on vendor driver does. This is required to make beacon
work on AP-mode, simply reading and then writing updated values is not enough
at least with zd1211b.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:48 -05:00
Jussi Kivilinna 8b17f75ced zd1211rw: add locking for mac->process_intr
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:48 -05:00
Jussi Kivilinna d741900d40 zd1211rw: cancel process_intr work on zd_chip_disable_int()
OOPS if worker is running and disconnect() is called (triggered
by unpluging device). Much harder to trigger at this stage but
later when we have AP beacon work in process_intr it happens very
easy.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:48 -05:00
Jussi Kivilinna 78fc800f06 zd1211rw: use urb anchors for tx and fix tx-queue disabling
When stress testing AP-mode I hit OOPS when unpluging or rmmodding
driver.

It appears that when tx-queue is disabled, tx-urbs might be left pending.
These can cause ehci to call non-existing tx_urb_complete() (after rmmod)
or uninitialized/reseted private structure (after disconnect()). Add skb
queue for submitted packets and unlink pending urbs on zd_usb_disable_tx().

Part of the problem seems to be usb->free_urb_list that isn't always
working as it should, causing machine freeze when trying to free the list
in zd_usb_disable_tx(). Caching free urbs isn't what other drivers seem
to be doing (usbnet for example) so strip free_usb_list.

Patch makes tx-urb handling saner with use of urb anchors.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:48 -05:00
Mohammed Shafi Shajakhan 9cf04dcc9c ath9k: Fix possible double free of PAPRD skb's
This patch reverts the following commit
ath9k: remove bfs_paprd_timestamp from struct ath_buf_state

Under high interference/noisy environment conditions where PAPRD frames
fails heavily introduces a possibility of double freeing skb's and causes
kernel panic after some time.This patch reverts back to the original approach
of using paprd_timestamp before freeing the PAPRD frame skb's

[  194.193705] Pid: 0, comm: swapper Tainted: G      D WC
2.6.35-22-generic #33-Ubuntu
[  194.193712] Call Trace:
[  194.193722]  [<c05c6468>] ? printk+0x2d/0x35
[  194.193732]  [<c05c63c3>] panic+0x5a/0xd2
[  194.193741]  [<c05ca3ed>] oops_end+0xcd/0xd0
[  194.193750]  [<c0105f74>] die+0x54/0x80
[  194.193758]  [<c05c9a16>] do_trap+0x96/0xc0
[  194.193837]  [<c0103fb0>] ? do_invalid_op+0x0/0xa0
[  194.193846]  [<c010403b>] do_invalid_op+0x8b/0xa0
[  194.193856]  [<c020bd4c>] ? kfree+0xec/0xf0
[  194.193866]  [<c012ce18>] ? default_spin_lock_flags+0x8/0x10
[  194.193877]  [<c01de47a>] ? free_one_page+0x12a/0x2d0
[  194.193888]  [<c01e04dc>] ? __free_pages+0x1c/0x40
[  194.193897]  [<c05c97a7>] error_code+0x73/0x78
[  194.193906]  [<c020bd4c>] ? kfree+0xec/0xf0
[  194.193915]  [<c04ecdd0>] ? skb_release_data+0x70/0xa0
[  194.193924]  [<c04ecdd0>] skb_release_data+0x70/0xa0
[  194.193933]  [<c04ec997>] __kfree_skb+0x17/0x90
[  194.193941]  [<c04eca31>] consume_skb+0x21/0x40
[  194.193964]  [<f85e0b70>] ieee80211_tx_status+0x760/0x860 [mac80211]
[  194.193979]  [<f85caddf>] ath_tx_complete_buf+0x1bf/0x2c0 [ath9k]
[  194.193988]  [<c05c8b9f>] ? _raw_spin_lock_irqsave+0x2f/0x50
[  194.193997]  [<c04ec40e>] ? skb_queue_tail+0x3e/0x50
[  194.194010]  [<f85cc803>] ath_tx_complete_aggr+0x823/0x940 [ath9k]
[  194.194021]  [<c0108a28>] ? sched_clock+0x8/0x10
[  194.194030]  [<c016bf14>] ? sched_clock_local+0xa4/0x180
[  194.194040]  [<c0139f57>] ? enqueue_sleeper+0x1e7/0x2b0
[  194.194051]  [<c013a194>] ? enqueue_entity+0x174/0x200
[  194.194064]  [<f85ce83d>] ath_tx_edma_tasklet+0x2bd/0x3b0 [ath9k]
[  194.194074]  [<c05c8b9f>] ? _raw_spin_lock_irqsave+0x2f/0x50
[  194.194088]  [<f85c7b9f>] ath9k_tasklet+0x9f/0x190 [ath9k]
[  194.194097]  [<c01505d7>] tasklet_action+0xa7/0xb0
[  194.194107]  [<c015127c>] __do_softirq+0x9c/0x1b0
[  194.194117]  [<c01a7f64>] ? irq_to_desc+0x14/0x20
[  194.194126]  [<c0124fc4>] ? ack_apic_level+0x64/0x1f0
[  194.194136]  [<c01513d5>] do_softirq+0x45/0x50
[  194.194145]  [<c0151545>] irq_exit+0x65/0x70
[  194.194153]  [<c05cf665>] do_IRQ+0x55/0xc0
[  194.194162]  [<c016a6c7>] ? hrtimer_start+0x27/0x30
[  194.194171]  [<c0103630>] common_interrupt+0x30/0x38
[  194.194181]  [<c012c21a>] ? native_safe_halt+0xa/0x10
[  194.194268]  [<c010a2f9>] default_idle+0x49/0xb0
[  194.194277]  [<c0101fcc>] cpu_idle+0x8c/0xd0
[  194.194286]  [<c05b2431>] rest_init+0x71/0x80
[  194.194295]  [<c081981a>] start_kernel+0x36e/0x374
[  194.194305]  [<c08199dd>] ? pass_all_bootoptions+0x0/0xa
[  194.194314]  [<c08190d7>] i386_start_kernel+0xd7/0xdf
[  194.194364] panic occurred, switching back to text console

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:11:39 -05:00
Christian Lamparter 5820de5303 carl9170: fix typo in PS code
This patch fixes a off-by-one bug which bugged
the driver's PS-POLL capability.

Cc: <stable@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:11:39 -05:00
Justin P. Mattock 942a84901b drivers:net:ipw2100.c change a typo comamnd to command
The below patch fixes a typo comamnd to command.

Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:45:29 -05:00
Rajkumar Manoharan 391bd1c443 ath9k: reserve a beacon slot on beaconing vif addition
The beaconing vif addition is based on max beacon slot
available. So it is better to reserve a beacon slot
on interface addition and let it be configured properly
on bss_info change.

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:45:29 -05:00
Ben Greear 4e6975f7b8 ath9k: Show channel type and frequency in debugfs.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:44:43 -05:00
Rajkumar Manoharan 4c89fe954d ath9k: do not access hw registers in FULL SLEEP
The opmode recalculation is accessing hw registers.
When it is called from remove interface callback and
if there are no vifs present then hw is moved to FULL SLEEP
by radio disable. So use power save wrappers before
accessing hw registers in calculating opmode state.

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:44:43 -05:00
Rajkumar Manoharan b2a5c3dfec ath9k_htc: make use common of function to update txpower
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:44:43 -05:00
Rajkumar Manoharan 5048e8c378 ath9k: move update tx power to common
move ath_update_txpow to common to remove code duplication
in both ath9k & ath9k_htc.

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:44:43 -05:00
Rajkumar Manoharan c344c9cb01 ath9k: use common get current channel function
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:44:43 -05:00
Rajkumar Manoharan 45655baa42 ath9k_htc: cancel ani work in ath9k_htc_stop
ani work is cancelled in dissaoctiation. But in some cases
during suspend, deauthention never be called. So we failed
to stop ani work which was identified by the following
warning.

Call Trace:
 [<ffffffffa0454a1d>] ieee80211_can_queue_work.clone.17+0x2d/0x40 [mac80211]
 [<ffffffffa0454a60>] ieee80211_queue_delayed_work+0x30/0x60 [mac80211]
 [<ffffffffa0567f82>] ath9k_ani_work+0x142/0x250 [ath9k_htc]
 [<ffffffff81073c70>] async_run_entry_fn+0x0/0x180
 [<ffffffffa0567e40>] ath9k_ani_work+0x0/0x250 [ath9k_htc]

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:44:42 -05:00
David Gnedt 73b30dfe4f wl1251: set rate index and preamble flag on received packets
Set the rate index rate_idx and preamble flag RX_FLAG_SHORTPRE on received
packets.

Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:44:42 -05:00
David Gnedt 43d136442a wl1251: enable adhoc mode
Enable adhoc support in wl1251 driver.

Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:44:42 -05:00
David Gnedt 8964e492b5 wl1251: implement connection quality monitoring
Implement connection quality monitoring similar to the wl1271 driver.
It triggers ieee80211_cqm_rssi_notify with the corresponding event when
RSSI drops blow RSSI threshold or rises again above the RSSI threshold.
It should be noted that wl1251 doesn't support RSSI hysteresis, instead it
uses RSSI averageing and delays events until a certain count of frames
proved RSSI change.

Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:44:42 -05:00
David Gnedt c3e334d294 wl1251: enable beacon early termination while in power-saving mode
Port the beacon early termination feature from wl1251 driver version
included in the Maemo Fremantle kernel.
It is enabled when going to power-saving mode and disabled when leaving
power-saving mode.

Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:42:44 -05:00
David Gnedt bb4793b3c6 wl1251: fix 4-byte TX buffer alignment
This implements TX buffer alignment for cloned or too small skb by
copying and replacing the original skb.
Recent changes in wireless-testing seems to make this really necessary.

Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:42:44 -05:00
David Gnedt e7332a4144 wl1251: fix queue stopping/waking for TX path
The queue stopping/waking functionality was broken in a way that could
cause the TX to stall if the right circumstances are met.

The problem was caused by tx_work, which is scheduled on each TX operation.
If the firmware buffer is full, tx_work does nothing. In combinition with
stopped queues or non-continues transfers, tx_work is never scheduled again.
Moreover the low watermark introduced by
9df86e2e70 never takes effect because of some
old code.

Solve this by scheduling tx_work every time tx_queue is non-empty and
firmware buffer is freed on tx_complete.

This also solves a possible but unlikely case: If less frames than the high
watermark are queued, but more than firmware buffer can hold. This results
in queues staying awake but the only scheduled tx_work doesn't transfer all
frames, so the remaining frames are stuck in the queue until more frames
get queued and tx_work is scheduled again.

Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:42:44 -05:00
Vasily Khoruzhick 75abde4d19 libertas: Prepare stuff for if_spi.c pm support
To support suspend/resume in if_spi we need two things:
- re-setup fw in lbs_resume(), because if_spi powercycles card;
- don't touch hwaddr on second lbs_update_hw_spec() call for same
  reason;

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:38:26 -05:00
Vasily Khoruzhick 16f775befc libertas_spi: Use workqueue in hw_host_to_card
Use workqueue to perform SPI xfers, it's necessary to fix
nasty "BUG: scheduling while atomic", because
spu_write() calls spi_sync() and spi_sync() may sleep, but
hw_host_to_card() callback can be called from atomic context.
Remove kthread completely, workqueue now does its job.
Restore intermediate buffers which were removed in commit
86c34fe89e that introduced
mentioned bug.

Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 16:38:25 -05:00
Jesper Juhl 4d048aac99 wireless, wl1251: Fix potential NULL pointer dereference in wl1251_op_bss_info_changed()
In drivers/net/wireless/wl1251/main.c:wl1251_op_bss_info_changed() we make
a call to ieee80211_beacon_get() which may return NULL, but we do not
check the return value before dereferencing the pointer.

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-03 15:23:53 -05:00
Wey-Yi Guy ff458edc0c iwlagn: overwrite EEPROM chain setting for 6250 devices
6250 2x2 devices have 2 tx chain and 2 rx chain. For some reason,
the EEPROM contain incorrect information and indicate it only has single
tx chain. overwrite it with .cfg parameter to make sure both chain 'A' and
chain 'B' can be used for transmit and receive

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-02 16:38:58 -05:00
Mohammed Shafi Shajakhan 479600777b ath9k: Fix memory leak due to failed PAPRD frames
free the skb's when the Tx of PAPRD frames fails and also add a debug
message indicating that.

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-01 11:06:00 -05:00
Wey-Yi Guy c52bf9b73a iiwlagn: remove unused parameter
sco_cmd is not being used, remove it

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-01-31 13:22:35 -08:00
Wey-Yi Guy 187bc4f6b2 iwlagn: remove unsupported BT SCO command
During the period of BT coex changes, REPLY_BT_COEX_SCO host command
is no longer needed to support SCO/eSCO type of traffic. delete it.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-01-31 13:22:25 -08:00
Wey-Yi Guy 96234cc84e iwlagn: use 2030 macro for 2030 devices
For 2030 series of devices, 2030 macro need to be used.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-01-31 13:22:13 -08:00
Johannes Berg 241887a2d3 iwlwifi: fix beacon notification parsing
The beacon notification changed between 4965 and
agn because the embedded TX response changed, but
iwlwifi was never updated to know about this.
Update it now so the IBSS manager status will be
tracked correctly.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-01-31 13:19:39 -08:00
Johannes Berg 7b09068721 iwlwifi: use maximum aggregation size
Use the values from the peer to set up the ucode
for the right maximum number of subframes in an
aggregate. Since the ucode only tracks this per
station, use the minimum across all aggregation
sessions with this peer.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-01-31 13:19:32 -08:00
Johannes Berg 9b76883284 iwlwifi: advertise max aggregate size
Allow peers to size their reorder buffer more
accurately by advertising that we'll never send
aggregates longer than the default (31).

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-01-31 13:19:24 -08:00
Johannes Berg 274102a8a2 iwlwifi: support RSN IBSS
In order to support RSN IBSS, we need to
(ok actually maybe it's just easiest to)
disable group key programming so that any
group-addressed frames will be decrypted
in software which handles the per-station
keys for this easily. We could keep the
encryption in the device, but that takes
more work and seems unnecessary.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-01-31 13:19:14 -08:00
Wey-Yi Guy 9dc2153315 iwlwifi: always support idle mode for agn devices
For agn devices, always support idle mode which help power
consumption in idle unassociated state.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-01-31 13:19:02 -08:00
Wey-Yi Guy 52e6b85fe0 iwlagn: add IQ inversion support for 2000 series devices
The I/Q swapping is extremely important and should be dealt with extra care.
It will affects OFDM and CCK differently.

For 6000/6005/6030 series devices, the I/Q were swapped, and for 2000 series
devices, it is in non-swapped status (but its swapped with respected to 6000/6005/6030).
so the CSR_GP_DRIVER_REG_BIT_RADIO_IQ_INVER register need to be set to support
the correct behavior.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-01-31 13:17:53 -08:00
Wey-Yi Guy 7fc11e9bbe iwlagn: adjust rate table
Minor adjustment for rate scale table

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-01-31 13:17:43 -08:00
Wey-Yi Guy 10480b0566 iwlwifi: check ucode loading error and restart
Driver check alive message from ucode, if it is not ok, then need
to restart the loading process. instead of checking multiple places
for failure, only need to check in once place when receive alive
message from uCode.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2011-01-31 13:17:28 -08:00
John W. Linville 78d12c237c Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
Conflicts:
	drivers/net/wireless/wl12xx/spi.c
2011-01-31 15:24:31 -05:00
Luciano Coelho 7c3ee9e3fd wl12xx: fix warning due to missing arg in ampdu_action
Commit 0b01f030d3 added a new argument
to the ampdu_action operation.  The ampdu_action operation in the
wl12xx driver currently doesn't have that argument and this generates
a warning.  This happened during merging of the latest mac80211
patches with the wl12xx BA patches.

  CC [M]  drivers/net/wireless/wl12xx/main.o
drivers/net/wireless/wl12xx/main.c:3035: warning: initialization from incompatible pointer type

The wl12xx driver doesn't need to do anything about the buf_size
argument since the AMPDU TX is fully handled by the firmware.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-31 15:11:38 -05:00
Stanislaw Gruszka 5a3a0352f3 iwlwifi: correct frequency settings
After commit 59eb21a650
"cfg80211: Extend channel to frequency mapping for 802.11j"
we use uninitialized sband->band when assign channel frequencies, what
results that 5GHz channels have erroneous (zero) center_freq value.

Patch fixes problem and simplifies code a bit.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-31 15:06:25 -05:00
Ivo van Doorn 0439f5367c rt2x00: Move TX/RX work into dedicated workqueue
The TX/RX work structures must be able to run independently
of other workqueues. This is because mac80211 might use
the flush() callback function from various context, which depends
on the TX/RX work to complete while the main thread is blocked
(until the the TX queues are empty).

This should reduce the number of  'Queue %d failed to flush' warnings.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-31 15:06:25 -05:00
Ivo van Doorn e1f4e808bb rt2x00: Kill all tasklets during device removal
During device removal all pending work and tasklets must
be guaranteed to be halted. So far only the txstatus_tasklet
was killed.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-31 15:06:25 -05:00
Gertjan van Wingerde a0aff623ca rt2x00: Fix FIXME comments in rt61pci and rt73usb on Michael MIC.
Both rt61pci and rt73usb check the Michael MIC in hardware and strip the
Michael MIC from received frames. This is perfectly allowed by mac80211 as
long as this is properly reported to mac80211.
Both these drivers reported the Michael MIC handling properly to mac80211, but
still contained a FIXME comment on this, which is not needed to be handled, since
mac80211 doesn't really need the Michael MIC in this case.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-31 15:06:25 -05:00
Gertjan van Wingerde 10026f77b3 rt2x00: Copy the MAC address to the WCID entry properly.
Use the specific mac field of the wcid_entry structure to copy the MAC
address to, instead of just overwriting the structure.
Previous code resulted in the same, but this form is cleaner.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-31 15:06:25 -05:00
Gertjan van Wingerde a45f369d47 rt2x00: Fix WPA TKIP Michael MIC failures.
As reported and found by Johannes Stezenbach:
rt2800{pci,usb} do not report the Michael MIC in RXed frames, but do check
the Michael MIC in hardware. Therefore we have to report to mac80211 that the
received frame does not include the Michael MIC.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-31 15:06:24 -05:00
Johannes Stezenbach 21957c31f6 rt2x00: trivial: add \n to WARNING message
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-31 15:06:24 -05:00
Mark Einon f5a9987dfb Trivial typo fix in comment
Fixing a trivial comment typo.

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-31 15:06:24 -05:00
RA-Jay Hung c6fcc0e5f7 rt2x00: Correct initial value of US_CYC_CNT register for pcie interface
CLOCK CYCLE: Clock cycle count in 1us
PCI:0x21, PCIE:0x7d, USB:0x1e

Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-31 15:06:24 -05:00
Helmut Schaa b550911abc rt2x00: Remove STATE_RADIO_IRQ_OFF_ISR and STATE_RADIO_IRQ_ON_ISR
Remove STATE_RADIO_IRQ_OFF_ISR and STATE_RADIO_IRQ_ON_ISR as they are
not used anymore.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-31 15:06:24 -05:00
Helmut Schaa e88399bcdb rt2x00: Remove interrupt thread registration
No driver uses interrupt threads anymore. Remove the remaining interrupt
thread artifacts.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-31 15:06:23 -05:00
Helmut Schaa bcf3cfd047 rt2x00: Convert rt2400pci interrupt handling to use tasklets
Fix interrupt processing on slow machines by using individual tasklets
for each different device interrupt. This ensures that while a RX or TX
status tasklet is scheduled only the according device interrupt is
masked and other interrupts such as TBTT can still be processed.

Also, this allows us to use tasklet_hi_schedule for TBTT processing
which is required to not send out beacons with a wrong DTIM count (due
to delayed periodic beacon updates). Furthermore, this improves the
latency between the TBTT and sending out buffered multi- and broadcast
traffic.

As a nice bonus, the interrupt handling overhead should be much lower.

Compile-tested only.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-31 15:06:23 -05:00
Helmut Schaa 16222a0d06 rt2x00: Convert rt2500pci interrupt handling to use tasklets
Fix interrupt processing on slow machines by using individual tasklets
for each different device interrupt. This ensures that while a RX or TX
status tasklet is scheduled only the according device interrupt is
masked and other interrupts such as TBTT can still be processed.

Also, this allows us to use tasklet_hi_schedule for TBTT processing
which is required to not send out beacons with a wrong DTIM count (due
to delayed periodic beacon updates). Furthermore, this improves the
latency between the TBTT and sending out buffered multi- and broadcast
traffic.

As a nice bonus, the interrupt handling overhead should be much lower.

Compile-tested only.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-31 15:06:23 -05:00
Helmut Schaa 5846a550b5 rt2x00: Convert rt61pci to use tasklets
Fix interrupt processing on slow machines by using individual tasklets
for each different device interrupt. This ensures that while a RX or TX
status tasklet is scheduled only the according device interrupt is
masked and other interrupts such as TBTT can still be processed.

Also, this allows us to use tasklet_hi_schedule for TBTT processing
which is required to not send out beacons with a wrong DTIM count (due
to delayed periodic beacon updates). Furthermore, this improves the
latency between the TBTT and sending out buffered multi- and broadcast
traffic.

As a nice bonus, the interrupt handling overhead should be much lower.

Compile-tested only.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-31 15:06:23 -05:00
Helmut Schaa a9d61e9e77 rt2x00: Convert rt2800pci to use tasklets
Fix interrupt processing on slow machines by using individual tasklets
for each different device interrupt. This ensures that while a RX or TX
status tasklet is scheduled only the according device interrupt is
masked and other interrupts such as TBTT can still be processed.

Also, this allows us to use tasklet_hi_schedule for TBTT and PRETBTT
processing which is required to not send out beacons with a wrong DTIM
count (due to delayed periodic beacon updates). Furthermore, this
improves the latency between the TBTT and sending out buffered multi-
and broadcast traffic.

As a nice bonus, the interrupt handling overhead is reduced such that
rt2800pci gains around 25% more throuhput on a rt3052 MIPS board.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-31 15:06:23 -05:00
Helmut Schaa c8e15a1e2c rt2x00: Disable txstatus tasklet by default
Enable the txstatus tasklet when interrupts are enabled and disable it
together with the interrupts. Also make the txstatus tasklet useful even
without the tx status FIFO and make use of the generic rt2x00 tasklet
initialization macro.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-31 15:06:23 -05:00
Helmut Schaa c5c6576183 rt2x00: Introduce tasklets for interrupt handling
No functional changes, just preparation for moving interrupt handling to
tasklets. The tasklets are disabled by default. Drivers making use of
them need to enable the tasklets when the device state is set to IRQ_ON.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-31 15:06:22 -05:00
Helmut Schaa 8d59c4e993 rt2x00: Make periodic beacon updates for PCI devices atomic
Allow the beacondone and pretbtt functions to update the beacon from
atomic context by using the beacon update functions with caller locking.

This is a preparation for moving the periodic beacon handling into
tasklets that require atomic context.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-31 15:06:22 -05:00
Helmut Schaa 1dae8d342e rt2x00: Limit beacon updates in bss_info_changed to USB devices
Currently there are two places that trigger a beacon update on PCI
devices. The bss_info_changed callback and the periodic update
triggered by the TBTT or PRETBTT interrupt.

Since the next TBTT or PRETBTT interrupt will periodically fetch an
updated beacon remove the update_beacon call in the bss_info_changed
callback for PCI devices.

In the worst case it will take one beacon interval longer to fetch
the new beacon then before. For devices that have a PRETBTT interrupt
there should be no change at all.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-31 15:06:22 -05:00
Helmut Schaa 8414ff07ac rt2x00: Introduce beacon_update_locked that requires caller locking
Introduce a beacon_update_locked function that does not acquire the
according beacon mutex to allow beacon updates from atomic context. The
caller has to take care of synchronization.

No functional changes. Just preparation for beacon updates from tasklet
context.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-31 15:06:22 -05:00
Helmut Schaa 69cf36a452 rt2x00: Refactor beacon code to make use of start- and stop_queue
This patch allows to dynamically remove beaconing interfaces without
shutting beaconing down on all interfaces.

The only place to start and stop beaconing are now the start- and
stop_queue callbacks. Hence, we can remove some register writes during
interface bring up (config_intf) and only write the correct sync mode
to the register there.

When multiple beaconing interfaces are present we should enable
beaconing as soon as mac80211 enables beaconing on at least one of
them. The beacon queue gets stopped when the last beaconing
interface was stopped by mac80211. Therefore, introduce another
interface counter to keep track ot the number of enabled beaconing
interfaces and start or stop the beacon queue accordingly.

To allow single interfaces to stop beaconing, add a new driver
callback clear_beacon to clear a single interface's beacon without
affecting the other interfaces. Don't overload the clear_entry callback
for clearing beacons as that would introduce additional overhead
(check for each TX queue) into the clear_entry callback which is used
on the drivers TX/RX hotpaths.

Furthermore, the write beacon callback doesn't need to enable beaconing
anymore but since beaconing should be disabled while a new beacon is
written or cleared we still disable beacon generation and enable it
afterwards again in the driver specific callbacks. However, beacon
related interrupts should not be disabled/enabled here, that's solely
done from the start- and stop queue callbacks. It would be nice to stop
the beacon queue just before the beacon update and enable it afterwards
in rt2x00queue itself instead of the current implementation that relies
on the driver doing the right thing. However, since start- and
stop_queue are mutex protected we cannot use them for atomic beacon
updates.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-31 15:06:22 -05:00
Stanislaw Gruszka d828cd5a95 iwl3945: do not use agn specific IWL_RATE_COUNT
Only use IWL_RATE_COUNT_3945 in 3945 code.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-31 15:06:21 -05:00
Mathias Krause 9b00b4157f wl12xx: fix use after free
When DEBUG_SPI is included in the debug log level wl1271_spi_reset()
will dump the already freed memory instead of the SPI buffer.

This bug was spotted by the semantic patch tool coccinelle using the
script found at scripts/coccinelle/free/kfree.cocci.

More information about semantic patching is available at
http://coccinelle.lip6.fr/

Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-31 14:48:15 -05:00
Mohammed Shafi Shajakhan b955fba29b ath9k: Fix memory leak due to failed PAPRD frames
free the skb's when the Tx of PAPRD frames fails and also add a debug
message indicating that.

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-31 14:48:15 -05:00
John W. Linville 3e11210d46 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
Conflicts:
	drivers/net/wireless/ath/ath9k/init.c
2011-01-28 16:23:14 -05:00
Felix Fietkau 3bf63e59e5 ath9k: fix compile error in non-debug ath_debug_stat_tx() stub
"ath9k: fix tx queue index confusion in debugfs code" changed the debug
function but not the stub.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:46:25 -05:00
Stanislaw Gruszka 9f60e7ee42 iwlwifi: introduce iwl_bt_statistics
We use priv->cfg->bt_params && priv->cfg->bt_params->bt_statistics
conditional in few places, merge it into one function.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:46:25 -05:00
Stanislaw Gruszka 8c9f514b38 iwlwifi: remove unneeded disable_hw_scan check
We never set STATUS_SCANNING in softwre scanning mode, disable_hw_scan
check is unneeded. Correct debug message while at it.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:46:25 -05:00
Stanislaw Gruszka 88e58fc5d9 iwlwifi: introduce iwl_advanced_bt_coexist()
We use priv->cfg->bt_params && priv->cfg->bt_params->advanced_bt_coexist
conditional in few places, merge it into one function.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:46:24 -05:00
Stanislaw Gruszka a839cf6955 iwlwifi: remove unneeded __packed
struct iwl_queue is not part of firmware interface, so __packed is not
needed. Remove it since is may affect performance.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:46:24 -05:00
Stanislaw Gruszka 5a5289dfa5 iwl3945: set STATUS_READY before commit_rxon
Similar change as we already do for agn, need to avoid
"Error setting Tx power (-5)" message when loading module.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:46:24 -05:00
Stanislaw Gruszka f844a709a7 iwlwifi: do not set tx power when channel is changing
Mac80211 can request for tx power and channel change in one ->config
call. If that happens, *_send_tx_power functions will try to setup tx
power for old channel, what can be not correct because we already change
the band. I.e  error  "Failed to get channel info for channel 140 [0]",
can be printed frequently when operating in software scanning mode.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:46:24 -05:00
Bruno Randolf 76a9f6fd9a ath5k: Fix short and long retry configuration
The register definition for retry configuration on AR5212 was wrong, and simply
copied over from AR5210. Update the register definitions from the documentation.

Let the short and long retries be configured from mac80211 and use the standard
values of 7 and 4 by default. Also we need to make sure we don't export more
retries than we are configured for to mac80211 (and the rate module) in
hw->max_rate_tries.

Also clean up the code by removing unused defines and variables and drop the
different values for "station retries" - if these need to be different it can
be handled tru ah_retry_long/short.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:46:23 -05:00
Rajkumar Manoharan de87f736e3 ath9k: use common API to avoid code duplication
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:46:23 -05:00
Vivek Natarajan ebefce3d13 ath9k_hw: Update PMU setting to improve ripple issue for AR9485.
Change from the systems team to update PMU setting for AR9485
version of chipsets.

Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:44:29 -05:00
Vivek Natarajan bdd62c067d ath9k: Fix a locking related issue.
Spin_lock has been tried to be acquired twice from ath9k_tasklet
to ath_reset which resulted in a machine freeze.

Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:44:29 -05:00
Vivek Natarajan 22983c301f ath9k_hw: DDR_PLL and BB_PLL need correct setting.
Updates from the analog team for AR9485 chipsets to set
DDR_PLL2 and DDR_PLL3. Also program the BB_PLL ki
and kd value.

Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:44:28 -05:00
Vivek Natarajan 181fb18daa ath9k: Fix a PLL hang issue observed with AR9485.
When this PLL hang issue is seen, both Rx and Tx fail to work.
The sqsum_dvc needs to be below 2000 for a good chip. During
this issue the sqsum_dvc value is beyond 80000 and only a
full reset can solve this problem.

Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:44:28 -05:00
Vivek Natarajan b141581923 ath9k_hw: Add a function to read sqsum_dvc.
Add a function to observe the delta VC of BB_PLL.
For a good chip, the sqsum_dvc is below 2000.

Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:44:28 -05:00
Sujith Manoharan 74f7635930 ath9k_hw: Add RX filters
The HW has separate filter masks for compressed/uncompressed
BlockAcks and BlockAckRequests. Add them.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:44:28 -05:00
Felix Fietkau 0d95521ea7 ath9k: use split rx buffers to get rid of order-1 skb allocations
With this change, less CPU time is spent trying to look for consecutive
pages for rx skbs. This also reduces the socket memory required for IP/UDP
reassembly.
Only two buffers per frame are supported. Frames spanning more buffers
will be dropped, but the buffer size is enough to handle the required
AMSDU size.

Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:44:28 -05:00
Sujith Manoharan 4d9067405c ath9k_hw: Fix INI fixup
Commit "ath9k_hw: move AR9280 PCI EEPROM fix to eeprom_def.c"
changed the behavior of INI overriding which is needed only
for PCI cards. Revert to the original check.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:44:27 -05:00
Sujith Manoharan 00e0003e09 ath9k_hw: Fix opmode initialization
Commit "ath9k_hw: Relocate Opmode initialization"
moved the opmode initialization before the STA_ID1 register
was programmed with defaults. This changed the original
behaviour because the re-programming code doesn't take into
account the existing value in the register. Both ath9k and ath9k_htc
were not affected by this change because the opmode is
re-initialized after every reset, when RX is started.

Revert to the original behavior, except keep it outside the
REGWRITE block. This would help remove extraneous opmode calls
in the driver core.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:44:27 -05:00
Bob Copeland 53e3b6e29e ath5k: remove debug_dump_skb() functions
Now that rx and tx dumps go through the tracing infrastructure,
we no longer need to keep these routines around.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:44:27 -05:00
Bob Copeland 0e4722524d ath5k: use tracing for packet tx/rx dump
This adds a few tracepoints to ath5k driver transmit and
receive callbacks in order to record packet traffic.
We record the entire packet in the trace buffer so that
the data can be extracted with trace-cmd and external
plugins.

Compared to the previous debugging calls, this approach
removes an out-of-line function call from the tx and rx
paths in the compiled-in-but-disabled case, while
improving the ability to process the logged data.

A new option, CONFIG_ATH5K_TRACER, is added so that one
may disable the tracepoints completely.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:44:27 -05:00
Bruno Randolf b453175d93 ath9k: Remove unused IEEE80211_WEP_NKID
IEEE80211_WEP_NKID is not used in ath9k any more since the key handling code
has been moved to ath/.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:44:26 -05:00
Bruno Randolf ead3dcff31 ath5k: Enable 802.11j 4.9GHz frequencies
This enables 4.9GHz frequencies in ath5k if they are allowed as indicated by
the regulatory domain code. Currently this is MKK9_MKKC (0xfe).

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:44:26 -05:00
Bruno Randolf 5719efdde1 ath: Add function to check if 4.9GHz channels are allowed
This adds a helper function to ath/regd.c which can be asked if 4.9GHz channels
are allowed for a given regulatory domain code. This keeps the knowledge of
regdomains and defines like MKK9_MKKC in one place. I'm passing the regdomain
code instead of the ath_regulatory structure because this needs to be called
quite early in the driver inititalization where ath_regulatory is not available
yet in ath5k.

I'm using MKK9_MKKC only because this is the regdomain in the 802.11j enabled
sample cards we got from our vendor. I found some hints in HAL code that this
is used by Atheros to indicate 4.9GHz channels support and that there might be
other domain codes as well, but as I don't have any documentation I'm just
putting in what I need right now. It can be extended later.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:44:26 -05:00
Bruno Randolf 20a904904d ath5k: Use local variable for capabilities
Shorten some lines and make code more readable.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:44:26 -05:00
Felix Fietkau 5bec3e5ade ath9k: fix tx queue index confusion in debugfs code
Various places printing tx queue information used various different ways to
get a tx queue index for printing statistics. Most of these ways were wrong.

ATH_TXQ_AC_* cannot be used as an index for sc->tx.txq, because it is only
used internally for queue assignment.

One place used WME_AC_* as a queue index for sc->debug.stats.txstats, however
this array uses the ath9k_hw queue number as well.

Fix all of this by always using the ath9k_hw queue number as an index, and
always looking it up by going through sc->tx.txq_map.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:42:00 -05:00
Felix Fietkau 9ac58615d9 ath9k: fold struct ath_wiphy into struct ath_softc
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:42:00 -05:00
Felix Fietkau 0cdd5c60e4 ath9k: remove the bf->aphy field
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:42:00 -05:00
Felix Fietkau 7545daf498 ath9k: remove support for virtual wiphys
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:41:59 -05:00
Felix Fietkau 34302397e5 ath9k: remove the virtual wiphy debugfs interface
It does not make much sense to keep the current virtual wiphy implementation
any longer - it adds significant complexity, has very few users and is still
very experimental. At some point in time, it will be replaced by a proper
implementation in mac80211.

By making the code easier to read and maintain, removing virtual wiphy support
helps with fixing the remaining driver issues and adding further improvements.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:39:40 -05:00
Felix Fietkau 9246041236 ath9k: clean up the code that wakes the mac80211 queues
Instead of spreading ath_wake_mac80211_queue() calls over multiple places
in the tx path that process the tx queue for completion, call it only
where the pending frames counter gets decremented, eliminating some
redundant checks.
To prevent queue draining from waking the queues prematurely (e.g. during
a hardware reset), reset the queue stop state when draining all queues,
as the caller in main.c will run ieee80211_wake_queues(hw) anyway.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:39:40 -05:00
John W. Linville cbdbc5eb54 Merge branch 'for-linville' of git://git.kernel.org/pub/scm/linux/kernel/git/luca/wl12xx 2011-01-28 15:33:16 -05:00
Rajkumar Manoharan c7c1806098 ath9k: Fix power save usage count imbalance on deinit
While unloading the driver, the ps_usecount is incremented
before configuring gpio registers in deinit_device.
But it is failed to restore the ps_usecount after that.
The problem is that the chip is forcibly moved to FULL SLEEP
by radio_disable when mac80211 is reporting as idle
though ps_usecount is not zero.

This patch retores ps_usecount properly and ensures that
the chip is always moved to full sleep only if ps usage
count is zero which also helps in debugging deadbeef on
multivif case. And also fixes the following warning.

ath: DMA failed to stop in 10 ms AR_CR=0xdeadbeef AR_DIAG_SW=0xdeadbeef
ath: Could not stop RX, we could be confusing the DMA engine when we
start RX up
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/recv.c:536
ath_stoprecv+0xf4/0x100 [ath9k]()

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:27:20 -05:00
Rajkumar Manoharan 5b64aa72ea ath9k_hw: Fix system hang when resuming from S3/S4
The bit 6 & 7 of AR_WA (0x4004) should be enabled only
for the chips that are supporting L0s functionality
while resuming back from S3/S4.

Enabling these bits for AR9280 is causing system hang
within a few S3/S4-resume cycles.

Cc: stable@kernel.org
Cc: Jack Lee <jlee@atheros.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-28 15:27:20 -05:00
Stanislaw Gruszka ea888357ec ath9k_htc: fix race conditions when stop device
We do not kill any scheduled tasklets when stopping device, that may
cause usage of resources after free. Disable interrupts, kill tasklets
and then works in correct order.

Cc: stable@kernel.org
Tested-by: Sujith <m.sujith@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-27 16:41:10 -05:00
Stanislaw Gruszka 203043f579 ath9k: fix race conditions when stop device
We do not kill any scheduled tasklets when stopping device, that may
cause usage of resources after free. Moreover we enable interrupts
in tasklet function, so we could potentially end with interrupts
enabled when driver is not ready to receive them.

I think patch should fix Ben's kernel crash from:
http://marc.info/?l=linux-wireless&m=129438358921501&w=2

Cc: stable@kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-27 16:41:08 -05:00
Bob Copeland c9234a662e ath5k: correct endianness of frame duration
The ath5k version of ieee80211_generic_frame_duration() returns
an __le16 for standard modes but a cpu-endian int for turbo/half/
quarter rates.  Make it always return cpu-endian values.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-27 16:41:07 -05:00
Bob Copeland 15411c27d2 ath5k: fix error handling in ath5k_hw_dma_stop
Review spotted a problem with the error handling in ath5k_hw_dma_stop:
a successful return from ath5k_hw_stop_tx_dma will be treated as
an error, so we always bail out of the loop after processing a single
active queue.  As a result, we may not actually stop some queues during
reset.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-27 16:40:51 -05:00
Chaoming Li bc5892c9ec rtlwifi: Fix firmware upload errors
When the source code from Realtek was prepared for kernel inclusion,
some routines were refactored to reduce the level of indentation. This
patch repairs errors introduced in that process.

Signed-off-by: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-27 16:32:19 -05:00
Felix Fietkau 8d8d3fdc0d ath9k: fix misplaced debug code
The commit 'ath9k: Add more information to debugfs xmit file.' added more
debug counters to ath9k and also added some lines of code to ath9k_hw.

Since ath9k_hw is also used by ath9k_htc, its code must not depend on ath9k
data structures. In this case it was not fatal, but it's still wrong, so
the code needs to be moved back to ath9k.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-27 16:03:59 -05:00
Christian Lamparter aa32452dcf carl9170: utilize fw seq counter for mgmt/non-QoS data frames
"mac80211 will properly assign sequence numbers to QoS-data
frames but cannot do so correctly for non-QoS-data and
management frames because beacons need them from that counter
as well and mac80211 cannot guarantee proper sequencing."

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-27 16:03:56 -05:00
Christian Lamparter c42d6cf25d carl9170: enable wake-on-lan feature testing
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-27 16:03:55 -05:00
Christian Lamparter 9e09b5c96c carl9170: update fw/hw headers
This patch syncs up the header files with
the project's main firmware carl9170fw.git.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-27 16:03:53 -05:00
Mohammed Shafi Shajakhan 436d0d9853 ath9k: clean up enums and unused macros
Remove unused macros and cleanup buffer_type enumeration

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-26 16:21:56 -05:00
John W. Linville 62362dee83 Merge branch 'wireless-next-2.6' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-2.6 2011-01-26 16:12:47 -05:00
Bruno Randolf 97d9c3a354 ath5k: ath5k_setup_channels cleanup and whitespace
Remove useless test_bit - it's not going to happen because of the way this
function is called only when that bit is set.

And fix some whitespace.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-25 16:39:06 -05:00
Senthil Balasubramanian 0a8d7cb0c8 ath9k_hw: read and backup AR_WA register value even before chip reset on.
We need to read and backup AR_WA register value permanently and reading
this after the chip is awakened results in this register being zeroed out.

This seems to fix the ASPM with L1 enabled issue that we have observed.
The laptop becomes very slow and hangs mostly with ASPM L1 enabled without
this fix.

Cc: Stable Kernel <stable@kernel.org>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-25 16:36:07 -05:00
Senthil Balasubramanian ac45c12dfb ath9k_hw: Fix incorrect macversion and macrev checks
There are few places where we are checking for macversion and revsions
before RTC is powered ON. However we are reading the macversion and
revisions only after RTC is powered ON and so both macversion and
revisions are actully zero and this leads to incorrect srev checks

Incorrect srev checks can cause registers to be configured wrongly and can
cause unexpected behavior. Fixing this seems to address the ASPM issue that
we have observed. The laptop becomes very slow and hangs mostly with ASPM L1
enabled without this fix.

fix this by reading the macversion and revisisons even before we start
using them. There is no reason why should we delay reading this info
until RTC is powered on as this is just a register information.

Cc: Stable Kernel <stable@kernel.org>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-25 16:33:27 -05:00
Greg Kroah-Hartman 9c4cf6d94f rt2x00: add device id for windy31 usb device
This patch adds the device id for the windy31 USB device to the rt73usb
driver.

Thanks to Ralf Flaxa for reporting this and providing testing and a
sample device.

Reported-by: Ralf Flaxa <rf@suse.de>
Tested-by: Ralf Flaxa <rf@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-01-25 16:28:56 -05:00
Eliad Peller e5e2f24b3e wl12xx: disable auto-arp
The auto-arp feature sometimes has unexpected side effects (e.g. firmware
crashes, no ARP replies, etc.)
disable it until it will be solved.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-01-24 23:44:27 +02:00
Juuso Oikarinen ea45b2cbf5 wl12xx: Increase scan channel dwell time for passive scans
The passive scan channel dwell time currently used is 30-60TU. A typical
beacon interval for AP's is 100TU. This leads to a ~30% worst-case probability
of finding an AP via passive scanning.

For 5GHz bands for DFS frequencies passive scanning is the only scanning
option. Hence for these, the probability of finding an AP is very low.

To fix this, increase the passive channel scan dwell times (also the early
leave value, as 5GHz channels are still typically very silent.) Use a value
of 100TU, because that covers most typical AP configurations.

Based on testing the probability of finding an AP (100TU beacon interval) on
a single scan round are as follows (based on 100 iterations):

dwell min/max (TU)   | probability
---------------------+------------
30/60                | 35%
60/60                | 56%
80/80                | 77%
100/100              | 100%

Total scan times now and after the change:

Region | Before (s) | After (s)
-------+------------+----------
00     | 0.77       | 1.48
FI     | 0.95       | 2.01
US     | 0.91       | 1.76

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-01-24 23:34:33 +02:00
Eliad Peller 8e2de74e78 wl12xx: wrong values are returned in gpio_power_write()
Return values were assigned to incorrect var / weren't assigned.
fix it, and defer mutex_lock after the sanity checks.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-01-24 23:15:11 +02:00
Levi, Shahar bbba3e6832 wl12xx: BA receiver support
Add new ampdu_action ops to support receiver BA.
The BA initiator session management in FW independently.

Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-01-24 22:58:47 +02:00
Levi, Shahar 4b7fac77b4 wl12xx: BA initiator support
Add 80211n BA initiator session support wl1271 driver.
Include BA supported FW version auto detection mechanism.
BA initiator session management included in FW independently.

Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-01-24 22:58:20 +02:00
Arik Nemtsov 6c89b7b2f8 wl12xx: Add channel 14 to list of supported 2ghz channels
Channel 14 is only supported in Japan (JP country code in regdb).  The
FW limits tranmissions to CCK only on this channel.

Tested in both STA and AP modes to work correctly.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-01-24 22:58:19 +02:00
Arik Nemtsov d75387ca62 wl12xx: add missing MODULE_FIRMWARE statment for AP-mode FW
In wl12xx cards AP-mode requires a separate FW file. Add this file to
the module info.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-01-24 22:58:18 +02:00
Juuso Oikarinen 4ae3fa8785 wl12xx: Cleanup PLT mode when module is removed
PLT mode start/stop is controlled from userspace. When removing module, the
PLT mode state is however not checked, and not cleared. There is the possibility
of some unwanted state to left linger and there is even the possiblity of a
kernel crash if for instance IRQ work is running when the module is removed.

Fix this by stopping PLT mode on module removal, if still running.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-01-24 22:16:09 +02:00
Eliad Peller 1d4801f268 wl12xx: fix some endianess bugs
pointed out by sparse warnings:

  CHECK   drivers/net/wireless/wl12xx/cmd.c
drivers/net/wireless/wl12xx/cmd.c:987:20: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/cmd.c:987:20:    expected restricted __le16 [usertype] aging_period
drivers/net/wireless/wl12xx/cmd.c:987:20:    got int
  CHECK   drivers/net/wireless/wl12xx/tx.c
drivers/net/wireless/wl12xx/tx.c:197:2: warning: cast from restricted __le16
drivers/net/wireless/wl12xx/tx.c:197:2: warning: cast from restricted __le16
drivers/net/wireless/wl12xx/tx.c:197:2: warning: cast from restricted __le16
  CHECK   drivers/net/wireless/wl12xx/acx.c
drivers/net/wireless/wl12xx/acx.c:816:23: warning: incorrect type in assignment (different base types)
drivers/net/wireless/wl12xx/acx.c:816:23:    expected restricted __le32 [usertype] rate_policy_idx
drivers/net/wireless/wl12xx/acx.c:816:23:    got unsigned char [unsigned] [usertype] idx

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-01-24 22:13:55 +02:00
Luciano Coelho 4c9cfa7806 wl12xx: add hw configuration for max supported AMDPU size
The wl12xx chips do the AMDPU aggregation work in the firmware, but it
supports a maximum of 8 frames per block.  Configure the mac80211 hw
structure accordingly.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Tested-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
2011-01-24 22:13:49 +02:00
Guy Eilam 491bbd6bdd wl12xx: change debug_level module param sysfs permissions
changed the visibility of the debug_level module parameter
in the filesystem to be readable and writable to the root user.
It is now accessible under /sys/module/wl12xx/parameters

removed the debug_level debugfs file that was created under
/sys/kernel/debug/...

Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-01-24 22:11:52 +02:00
Luciano Coelho 2d6e4e76d1 wl12xx: lock the RCU when accessing sta via ieee80211_find_sta()
We were calling ieee80211_find_sta() and the sta returned by it
without locking the RCU, which is required by mac80211.

Fix this and reorganize slightly the area of the code where the sta is
used.

Reported-by: Jonathan DE CESCO <jonathanc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-01-24 22:11:52 +02:00
Luciano Coelho a8aaaf53d5 wl12xx: don't modify the global supported band structures
When 11a is not supported, we were modifying the global structure that
contains the bands supported by the driver.  This causes problems when
having more one wl12xx device in the same system because they all use
the same global.  This also causes problems when the wl12xx_sdio
module is removed and the wl12xx module remains.

Fix this problem by copying the band structure into the wl12xx
instance.

Reported-by: Arik Nemtsov <arik@wizery.com>
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-01-24 22:11:52 +02:00
Eliad Peller fa287b8f29 wl12xx: don't join upon disassociation
wl12xx "rejoins" upon every BSS_CHANGED_BSSID notification.
However, there is no need to rejoin after disassociation, so just
filter out the case when the new bssid is 00:00:00:00:00:00.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-01-24 22:11:51 +02:00
Arik Nemtsov 038d925bcf wl12xx: Enable AP-mode
Indicate support for the NL80211_IFTYPE_AP interface mode to enable AP
mode operation.

Disable 11a when operating in AP-mode (unsupported for now).

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-01-24 22:11:51 +02:00
Arik Nemtsov 31d26ec699 wl12xx: Read MAC address from NVS file on HW startup
Try to read the MAC address from the on-disk NVS file.
A non-zero MAC address is required to add an AP interface.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-01-24 22:11:51 +02:00
Arik Nemtsov 166d504eba wl12xx: AP mode - fetch appropriate firmware for AP
AP and STA modes use different firmwares.

Differentiate the firmware files by name and fetch the appropriate one
when add_interface is called by mac80211. The STA firmware is chosen for
PLT mode.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-01-24 22:11:50 +02:00
Arik Nemtsov 7f179b4689 wl12xx: AP mode - encryption support
Encryption key configuration is different for AP/STA modes.

AP encryption keys are recorded when the BSS is not started. On BSS
start they are propagated to the AP (in wl1271_ap_init_hwenc).

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-01-24 22:11:50 +02:00
Arik Nemtsov 488fc54047 wl12xx: AP mode - record TX configuration settings
Record TX configuration settings in the "conf" member of our global
structure (struct wl1271) if conf_tx is called when the firmware is
not loaded.

Later on when the firmware is loaded, we apply the tx conf as part of
the init sequence.

Important for AP mode since conf_tx is called before add_interface
(where the firmware is initialized).

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-01-24 22:11:50 +02:00
Arik Nemtsov c6c8a65de6 wl12xx: AP mode - changes in TX path
When in AP mode set appropriate HLID and rate policy for each skb.
Respond to supported-rates related changes in op_tx only when acting
as STA.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-01-24 22:11:50 +02:00
Arik Nemtsov f84f7d78bb wl12xx: AP mode - add STA add/remove ops
Allocate and free host link IDs (HLIDs) for each link. A per-STA
data structure keeps the HLID of each STA.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-01-24 22:11:49 +02:00
Arik Nemtsov 7d05786931 wl12xx: AP mode - change filter config
Do not configure a group address table in AP mode

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-01-24 22:11:49 +02:00
Arik Nemtsov bee0ffec77 wl12xx: AP mode config in ieee80211_ops.config
Separate configuration according to mode. AP has different rate
set configuration and no handling of idle-state.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-01-24 22:11:49 +02:00
Arik Nemtsov e78a287ab7 wl12xx: Configure AP on BSS info change
Configure AP-specific beacon and probe response templates.
Start the AP when beaconing is enabled.

The wl1271_bss_info_changed() function has been split into AP/STA
specific handlers.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-01-24 22:11:49 +02:00