This patch adds support of hardware rx-vlan-offload to VF driver.
VF uses mailbox to convey PF to configure the hardware.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset Asserting message is forwarded by PF to inform VF about
the hardware reset which is about to happen. This might be due
to the earlier VF reset request received by the PF or because PF
for any reason decides to undergo reset. This message results in
VF to go in pending state in which it polls the hardware to
complete the reset and then further resets/tears its own stack.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current mailbox CRQ could consists of both synchronous and async
responses from the PF. Synchronous responses are time critical
and should be handed over to the waiting tasks/context as quickly
as possible otherwise timeout occurs.
Above problem gets accentuated if CRQ consists of even single
async message. Hence, it is important to have quick handling of
synchronous messages and maybe deferred handling of async messages
This patch introduces separate ARQ(async receive queues) for the
async messages. These messages are processed later with repsect
to mailbox task while synchronous messages still gets processed
in context to mailbox interrupt.
ARQ is important as VF reset introduces some new async messages
like MBX_ASSERTING_RESET which adds up to the presssure on the
responses for synchronousmessages and they timeout even more
quickly.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the hardware reset we should re-fetch the configuration from
PF like queue info and tc info. This might have impact on allocations
made like that of TQPs. Hence, we should release all such allocations
and re-allocate fresh according to new fetched configuration after
reset.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After VF driver knows that hardware reset has been performed
successfully, it should proceed ahead and reset the enet layer.
This primarily consists of bringing down interface, clearing
TX/RX rings, disassociating vectors from ring etc.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF driver depends upon PF to eventually reset the hardware. This
request is made using the mailbox command. This patch adds the
required function to acheive above.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces the hclge device reset states of "requested" and
"pending" and also its handling in context to Reset Service Task.
Device gets into requested state because of any VF reset request
asserted from upper layers, for example due to watchdog timeout
expiration. Requested state would result in eventually forwarding
the VF reset request to PF which would actually reset the VF.
Device will get into pending state if:
1. VF receives the acknowledgement from PF for the VF reset
request it originally sent to PF.
2. Reset Service Task detects that after asserting VF reset for
certain times the data-path is not working and device then
decides to assert full VF reset(this means also resetting the
PCIe interface).
3. PF intimates the VF that it has undergone reset.
Pending state would result in VF to poll for hardware reset
completion status and then resetting the stack/enet layer, which
in turn means reinitializing the ring management/enet layer.
Note: we would be adding support of 3. later as a separate patch.
This decision should not affect VF reset as its event handling
is generic in nature.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF reset would involve handling of different reset related events
from the stack, physical function, mailbox etc. Reset service task
would be used in servicing such reset event requests and later
handling the hardware completions waits and initiating the stack
resets.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS3 drivers enet layer, used for the ring management and stack
interaction, is common to both VF and PF. PF already supports reset
functionality to handle the network stack watchdog timeout trigger
but the existing code is not generic enough to be used to support VF
reset as well.
This patch does following:
1. Makes the existing watchdog timeout handler in enet layer generic
i.e. suitable for both VF and PF and
2. Introduces the new reset event handler for the VF code.
3. Changes existing reset event handler of PF code to initialize the
reset level
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for querying speed and duplex by ethtool ethX
to VF.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds ethtool_ops.get_link support to VF.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It may need more time for IMP handle some command, such as reset.
This patch enlarges the max time for cmd timeout.
Driver will check the IMP result every us, it may break through the
loop when get the right result. So not all command need the max time.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no module that is dependent on hclge or hclgevf's symbol,
but hns_enet need them to provide ops for it to run. When there is
a need to auto load the hns3 driver, the auto load will fail because
hclge or hclgevf is not loaded.
Hns_enet has already exported the pci table, so this patch exports
the pci table for hclge and hclgevf module too.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF queue reset flow is different from PF queue reset flow.
VF driver should stop VF queue first, then send message to PF
and PF do the reset. PF should send a response to VF after
PF complete the queue reset, VF can initialize the queue hw
after get the response.
This patch fixes the VF queue reset flow as the correct step.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF changes unicast mac address by sending mailbox msg to PF, then PF
completes the mac address modification. It may fail when the target
uc mac address is already in the mac_vlan table. VF should be aware
of it by reading the message result.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the buffer overflow warning by refactoring
hclgevf_bind_ring_to_vector and hclge_get_ring_chain_from_mbx.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Fixes: dde1a86e93 ("net: hns3: Add mailbox support to PF driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link status update function is called by timer every second. But
net_stop and net_open may be called with very short intervals. The link
status update function can not detect the link state has changed. It
causes the netdev not running problem.
This patch fixes it by updating the link state in ae_stop function.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When driver is in initial state, the mac_vlan table table is empty.
So the delete operation for mac address must fail. Existence check
is needed here. Otherwise, the error message will make user confused.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a get_vector function, which allocate the vectors
for a client, but there is not a put_vector to free the
vector.
This patch introduces the put_vector function in order to
fix the coalesce configuration lost problem during reset
process.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for VF driver inner interface
hclgevf_ops.get_tqps_and_rss_info. This interface will be
used in the initialization process.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver check the out_vld bit when get a new cmdq BD, if the bit is 1,
the BD is valid. driver Should set the bit 0 after used and hw will
set the bit 1 if get a valid BD.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just like PF, if the int_gl_idx of VF does not be set, the default
interrupt coalesce index of VF is 0. But it should be GL1 for TX
queues and GL0 for RX queues.
This patch adds the int_gl_idx setup for VF.
Fixes: 200ecda42598 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only main PF can config TSO MSS length according to hardware.
This patch removes TSO config command from VF driver.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch supports the ethtool's get_channels() for VF.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a redundant semicolon, this patch removes it.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The result of tqp statistics query was read with an
error position, fix it according to the user manual.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some members of packet statistics are named in different styles.
This patch unifies them with new internal name rules, the main
modification are below:
trans --> tx
rcv --> rx
rcb_q%d_tx --> txq#%d
rcb_q%d_rx --> rxq#%d
sw_err_cnt(tx side) --> tx_dropped
sw_err_cnt(rx side) --> rx_dropped
pkts --> packets
tx_err_cnt --> errors
rx_err_cnt --> errors
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the NAPI handling interface, skb buffer management,
management of the RX/TX descriptors, ethool interface etc.
has quite a bit of code which is common to VF and PF driver.
This patch makes the exisitng PF's HNS3 ENET driver as the
common ENET driver for both Virtual & Physical Function. This
will help in reduction of redundancy and better management of
code.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the new Makefiles and updates existing
Makefiles required to build the HNS3 Virtual Function driver.
This also updates the Kconfig for introduction of new menuconfig
entries related to VF driver.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of hardware compatibiltiy layer to the
HNS3 VF Driver. This layer implements various {set|get} operations
over MAC address for a virtual port, RSS related configuration,
fetches the link status info from PF, does various VLAN related
configuration over the virtual port, queries the statistics from
the hardware etc.
This layer can directly interact with hardware through the
IMP(Integrated Mangement Processor) interface or can use mailbox
to interact with the PF driver.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of the mailbox to the VF driver. The
mailbox shall be used as an interface to communicate with the
PF driver for various purposes like {set|get} MAC related
operations, reset, link status etc. The mailbox supports both
synchronous and asynchronous command send to PF driver.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support of command interface for communication with
the IMP(Integrated Management Processor) for HNS3 Virtual Function
Driver.
Each VF has support of CQP(Command Queue Pair) ring interface.
Each CQP consis of send queue CSQ and receive queue CRQ.
There are various commands a VF may support, like to query frimware
version, TQP management, statistics, interrupt related, mailbox etc.
This also contains code to initialize the command queue, manage the
command queue descriptors and Rx/Tx protocol with the command processor
in the form of various commands/results and acknowledgements.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yunsheng Lin