The commit 85256f611f ("extcon: ptn5150: Check current USB mode when
probing") reused code for checking CC status register in the probe path
to determine what is initially connected. However if nothing is
connected, the CC status register will have 0x0 value and print an error
message:
ptn5150 1-003d: Unknown Port status : 0
This is not an error. Also any other unknown port status values are not
really errors but unhandled cases.
Fixes: 85256f611f ("extcon: ptn5150: Check current USB mode when probing")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The register addresses are not continuous, so use simple defines for
them. This also makes it easier to find the address for register.
No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Set the capability value of property for VBUS and POLARITY.
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
[cw00.choi: Replace the space with tab for the indentation]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
dev_err_probe() is designed to be used like
return dev_err_probe(dev, ret, "Error message\n");
Hence no need to have a separate return statement. Besides that
dev_err_probe() prints already returned error code, no need to repeat
that either.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The 'struct i2c_device_id' argument of probe function is not used, so
convert the driver to simpler 'probe_new' interface.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Vijai Kumar K <vijaikumar.kanagarajan@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Use module_i2c_driver() to simplify driver init boilerplate.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Vijai Kumar K <vijaikumar.kanagarajan@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
There is no point to print deferred probe (and its failures to get
resources) as an error. In case of multiple probe tries this would
pollute the dmesg.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Vijai Kumar K <vijaikumar.kanagarajan@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The PTN5150 chip can be used in hardware designs with only reporting of
USB Type-C connection, without the VBUS control. The driver however
unconditionally expected 'vbus-gpios'.
Since all uses of the VBUS GPIO descriptor are NULL safe, the code can
accept missing GPIO and provide only extcon status reporting.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Vijai Kumar K <vijaikumar.kanagarajan@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
When machine boots up, the USB could be already in OTG mode. In such
case there will be no interrupt coming to ptn5150 device and driver will
report default state of nothing connected. Detection of USB connection
would happen on first unplug of the cable.
Factor out code for checking current connection mode and call it right
after probe so the existing USB mode will be properly reported.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Vijai Kumar K <vijaikumar.kanagarajan@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The ptn5150 driver always prints device type on probe but as raw hex,
without any translation to meaningful description. This is useful only
for board bring up time so lower the verbosity to debug.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Vijai Kumar K <vijaikumar.kanagarajan@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Instead of obtaining GPIO as input and configuring it right after to
output-low, just use proper GPIOD_OUT_LOW flag. Code is smaller and
simpler.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Vijai Kumar K <vijaikumar.kanagarajan@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Interrupts do not have to be always GPIO based so instead of expecting
"int-gpios" property and converting the GPIO to an interrupt, just
accept any interrupt via generic "interrupts" property.
Keep support for old "int-gpios" for backward compatibility.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Vijai Kumar K <vijaikumar.kanagarajan@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The driver uses atomic version of gpiod_set_value() without any real
reason. It is called in a workqueue under mutex so it could sleep
there. Changing it to "can_sleep" flavor allows to use the driver with
all GPIO chips.
Fixes: 4ed754de2d ("extcon: Add support for ptn5150 extcon driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Vijai Kumar K <vijaikumar.kanagarajan@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
In case of error, the function devm_gpiod_get() returns ERR_PTR() and
never returns NULL. The NULL test in the return value check should be
replaced with IS_ERR().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
PTN5150 is a small thin low power CC (Configurationn Channel)
Logic chip supporting the USB Type-C connector application with
CC control logic detection and indication functions.
Signed-off-by: Vijai Kumar K <vijaikumar.kanagarajan@gmail.com>
[cw00.choi: Fix bulid dependency and clean-up code]
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Krzysztof Kozlowski