The kerneldoc for irq_set_irq_wake() says:
Enable/disable power management wakeup mode, which is
disabled by default.
regmap_irq_set_wake() clears bits to enable wake for an interrupt,
and sets bits to disable wake. Hence, we should set all bits in
wake_buf initially, to mirror the expected disabled state.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If a regmap-irq chip has no wake base:
* There's no point calling .irq_set_wake, hence IRQCHIP_SKIP_SET_WAKE.
* If some IRQs in the chip are enabled for wake and some aren't, we
should mask those interrupts that are not wake enabled, so that if
they occur during suspend, the system is not awoken. Hence,
IRQCHIP_MASK_ON_SUSPEND.
Note that IRQCHIP_MASK_ON_SUSPEND is handled by check_wakeup_irqs(),
which always iterates over every single interrupt in the system,
irrespective of whether an interrupt is a child of a controller whose
output interrupt has no wake-enabled inputs and hence is presumably
masked itself. Hence this change might cause interrupt unnecessary
masking operations and associated register I/O.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is intended to give each irq_chip a useful name, rather than hard-
coding them all as "regmap".
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This will allow later patches to adjust portions of the irq_chip
individually for each regmap_irq_chip that is created.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Don't write the full register, it's possible there's bits other than the
masks in the same register which we shouldn't be changing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
A number of places in the code were printing error messages that included
the address of a register, but were not calculating the register address
in the same way as the access to the register. Use a temporary to solve
this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When bus->fast_io is set, the locking here is done with spinlocks.
This is currently true for the regmap-mmio bus implementation.
While holding a spinlock we can't go to sleep, various operations
like removing the debugfs entries or re-initializing the cache will
sleep, therefore, shift the locking up to the user.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pull second vfs pile from Al Viro:
"The stuff in there: fsfreeze deadlock fixes by Jan (essentially, the
deadlock reproduced by xfstests 068), symlink and hardlink restriction
patches, plus assorted cleanups and fixes.
Note that another fsfreeze deadlock (emergency thaw one) is *not*
dealt with - the series by Fernando conflicts a lot with Jan's, breaks
userland ABI (FIFREEZE semantics gets changed) and trades the deadlock
for massive vfsmount leak; this is going to be handled next cycle.
There probably will be another pull request, but that stuff won't be
in it."
Fix up trivial conflicts due to unrelated changes next to each other in
drivers/{staging/gdm72xx/usb_boot.c, usb/gadget/storage_common.c}
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (54 commits)
delousing target_core_file a bit
Documentation: Correct s_umount state for freeze_fs/unfreeze_fs
fs: Remove old freezing mechanism
ext2: Implement freezing
btrfs: Convert to new freezing mechanism
nilfs2: Convert to new freezing mechanism
ntfs: Convert to new freezing mechanism
fuse: Convert to new freezing mechanism
gfs2: Convert to new freezing mechanism
ocfs2: Convert to new freezing mechanism
xfs: Convert to new freezing code
ext4: Convert to new freezing mechanism
fs: Protect write paths by sb_start_write - sb_end_write
fs: Skip atime update on frozen filesystem
fs: Add freezing handling to mnt_want_write() / mnt_drop_write()
fs: Improve filesystem freezing handling
switch the protection of percpu_counter list to spinlock
nfsd: Push mnt_want_write() outside of i_mutex
btrfs: Push mnt_want_write() outside of i_mutex
fat: Push mnt_want_write() outside of i_mutex
...
mm/page_alloc.c has some memory isolation functions but they are used only
when we enable CONFIG_{CMA|MEMORY_HOTPLUG|MEMORY_FAILURE}. So let's make
it configurable by new CONFIG_MEMORY_ISOLATION so that it can reduce
binary size and we can check it simple by CONFIG_MEMORY_ISOLATION, not if
defined CONFIG_{CMA|MEMORY_HOTPLUG|MEMORY_FAILURE}.
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull DMA-mapping updates from Marek Szyprowski:
"Those patches are continuation of my earlier work.
They contains extensions to DMA-mapping framework to remove limitation
of the current ARM implementation (like limited total size of DMA
coherent/write combine buffers), improve performance of buffer sharing
between devices (attributes to skip cpu cache operations or creation
of additional kernel mapping for some specific use cases) as well as
some unification of the common code for dma_mmap_attrs() and
dma_mmap_coherent() functions. All extensions have been implemented
and tested for ARM architecture."
* 'for-linus-for-3.6-rc1' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: dma-mapping: add support for DMA_ATTR_SKIP_CPU_SYNC attribute
common: DMA-mapping: add DMA_ATTR_SKIP_CPU_SYNC attribute
ARM: dma-mapping: add support for dma_get_sgtable()
common: dma-mapping: introduce dma_get_sgtable() function
ARM: dma-mapping: add support for DMA_ATTR_NO_KERNEL_MAPPING attribute
common: DMA-mapping: add DMA_ATTR_NO_KERNEL_MAPPING attribute
common: dma-mapping: add support for generic dma_mmap_* calls
ARM: dma-mapping: fix error path for memory allocation failure
ARM: dma-mapping: add more sanity checks in arm_dma_mmap()
ARM: dma-mapping: remove custom consistent dma region
mm: vmalloc: use const void * for caller argument
scatterlist: add sg_alloc_table_from_pages function
This patch adds dma_get_sgtable() function which is required to let
drivers to share the buffers allocated by DMA-mapping subsystem. Right
now the driver gets a dma address of the allocated buffer and the kernel
virtual mapping for it. If it wants to share it with other device (= map
into its dma address space) it usually hacks around kernel virtual
addresses to get pointers to pages or assumes that both devices share
the DMA address space. Both solutions are just hacks for the special
cases, which should be avoided in the final version of buffer sharing.
To solve this issue in a generic way, a new call to DMA mapping has been
introduced - dma_get_sgtable(). It allocates a scatter-list which
describes the allocated buffer and lets the driver(s) to use it with
other device(s) by calling dma_map_sg() on it.
This patch provides a generic implementation based on virt_to_page()
call. Architectures which require more sophisticated translation might
provide their own get_sgtable() methods.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Commit 9adc5374 ('common: dma-mapping: introduce mmap method') added a
generic method for implementing mmap user call to dma_map_ops structure.
This patch converts ARM and PowerPC architectures (the only providers of
dma_mmap_coherent/dma_mmap_writecombine calls) to use this generic
dma_map_ops based call and adds a generic cross architecture
definition for dma_mmap_attrs, dma_mmap_coherent, dma_mmap_writecombine
functions.
The generic mmap virt_to_page-based fallback implementation is provided for
architectures which don't provide their own implementation for mmap method.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Here's the big driver core pull request for 3.6-rc1.
Unlike 3.5, this kernel should be a lot tamer, with the printk changes now
settled down. All we have here is some extcon driver updates, w1 driver
updates, a few printk cleanups that weren't needed for 3.5, but are good to
have now, and some other minor fixes/changes in the driver core.
All of these have been in the linux-next releases for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAlARgIUACgkQMUfUDdst+ynDHgCfRNwIB9L+zZvjcKE5e1BhDbUl
wVUAn398DFgbJ1+PjGkd1EMR2uVTh7Ou
=MIFu
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core changes from Greg Kroah-Hartman:
"Here's the big driver core pull request for 3.6-rc1.
Unlike 3.5, this kernel should be a lot tamer, with the printk changes
now settled down. All we have here is some extcon driver updates, w1
driver updates, a few printk cleanups that weren't needed for 3.5, but
are good to have now, and some other minor fixes/changes in the driver
core.
All of these have been in the linux-next releases for a while now.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (38 commits)
printk: Export struct log size and member offsets through vmcoreinfo
Drivers: hv: Change the hex constant to a decimal constant
driver core: don't trigger uevent after failure
extcon: MAX77693: Add extcon-max77693 driver to support Maxim MAX77693 MUIC device
sysfs: fail dentry revalidation after namespace change fix
sysfs: fail dentry revalidation after namespace change
extcon: spelling of detach in function doc
extcon: arizona: Stop microphone detection if we give up on it
extcon: arizona: Update cable reporting calls and split headset
PM / Runtime: Do not increment device usage counts before probing
kmsg - do not flush partial lines when the console is busy
kmsg - export "continuation record" flag to /dev/kmsg
kmsg - avoid warning for CONFIG_PRINTK=n compilations
kmsg - properly print over-long continuation lines
driver-core: Use kobj_to_dev instead of re-implementing it
driver-core: Move kobj_to_dev from genhd.h to device.h
driver core: Move deferred devices to the end of dpm_list before probing
driver core: move uevent call to driver_register
driver core: fix shutdown races with probe/remove(v3)
Extcon: Arizona: Add driver for Wolfson Arizona class devices
...
The most important feature of this patch set is the new async infrastructure
that makes sure async_synchronize_full() synchronizes all domains and allows
us to remove all the hacks (like having scsi_complete_async_scans() in the
device base code) and means that the async infrastructure will "just work" in
future. The rest is assorted driver updates (aacraid, bnx2fc, virto-scsi,
megaraid, bfa, lpfc, qla2xxx, qla4xxx) plus a lot of infrastructure work in
sas and FC.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQDjDCAAoJEDeqqVYsXL0M/sMH/jVgBfF1mjR+DQuTscKyD21w
0BQLn5OmvDZDqo44iqQzNRObw7CxkBkUtHoozsknLijw+KggER653ZOAtUdIHfI/
/uo7iJQ3J3D/Ezm99HYSpZiF2juZwsBRtFBoKkGqOpMlzFUx5o4hUbH5OcINxnHR
VmvJU5K1kg8D77Q6zK+Atl14/Rfibc2IoufFmbYdplUAM/tV0BpBSSHJAJvqua76
NGMl4KJcPZnXe/4LXcxZia5A2efdFFEzaQ2mM9rUVEAgHDAxc0Zg9IoDhGd08FX4
G55NK+6+bKb9s7bgyva0T/iy817TRCzjteeYNFrb8nBRe7aQbAivaBHQFXIyvdQ=
=y2sh
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"The most important feature of this patch set is the new async
infrastructure that makes sure async_synchronize_full() synchronizes
all domains and allows us to remove all the hacks (like having
scsi_complete_async_scans() in the device base code) and means that
the async infrastructure will "just work" in future.
The rest is assorted driver updates (aacraid, bnx2fc, virto-scsi,
megaraid, bfa, lpfc, qla2xxx, qla4xxx) plus a lot of infrastructure
work in sas and FC.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (97 commits)
[SCSI] Revert "[SCSI] fix async probe regression"
[SCSI] cleanup usages of scsi_complete_async_scans
[SCSI] queue async scan work to an async_schedule domain
[SCSI] async: make async_synchronize_full() flush all work regardless of domain
[SCSI] async: introduce 'async_domain' type
[SCSI] bfa: Fix to set correct return error codes and misc cleanup.
[SCSI] aacraid: Series 7 Async. (performance) mode support
[SCSI] aha152x: Allow use on 64bit systems
[SCSI] virtio-scsi: Add vdrv->scan for post VIRTIO_CONFIG_S_DRIVER_OK LUN scanning
[SCSI] bfa: squelch lockdep complaint with a spin_lock_init
[SCSI] qla2xxx: remove unnecessary reads of PCI_CAP_ID_EXP
[SCSI] qla4xxx: remove unnecessary read of PCI_CAP_ID_EXP
[SCSI] ufs: fix incorrect return value about SUCCESS and FAILED
[SCSI] ufs: reverse the ufshcd_is_device_present logic
[SCSI] ufs: use module_pci_driver
[SCSI] usb-storage: update usb devices for write cache quirk in quirk list.
[SCSI] usb-storage: add support for write cache quirk
[SCSI] set to WCE if usb cache quirk is present.
[SCSI] virtio-scsi: hotplug support for virtio-scsi
[SCSI] virtio-scsi: split scatterlist per target
...
Pull the big VFS changes from Al Viro:
"This one is *big* and changes quite a few things around VFS. What's in there:
- the first of two really major architecture changes - death to open
intents.
The former is finally there; it was very long in making, but with
Miklos getting through really hard and messy final push in
fs/namei.c, we finally have it. Unlike his variant, this one
doesn't introduce struct opendata; what we have instead is
->atomic_open() taking preallocated struct file * and passing
everything via its fields.
Instead of returning struct file *, it returns -E... on error, 0
on success and 1 in "deal with it yourself" case (e.g. symlink
found on server, etc.).
See comments before fs/namei.c:atomic_open(). That made a lot of
goodies finally possible and quite a few are in that pile:
->lookup(), ->d_revalidate() and ->create() do not get struct
nameidata * anymore; ->lookup() and ->d_revalidate() get lookup
flags instead, ->create() gets "do we want it exclusive" flag.
With the introduction of new helper (kern_path_locked()) we are rid
of all struct nameidata instances outside of fs/namei.c; it's still
visible in namei.h, but not for long. Come the next cycle,
declaration will move either to fs/internal.h or to fs/namei.c
itself. [me, miklos, hch]
- The second major change: behaviour of final fput(). Now we have
__fput() done without any locks held by caller *and* not from deep
in call stack.
That obviously lifts a lot of constraints on the locking in there.
Moreover, it's legal now to call fput() from atomic contexts (which
has immediately simplified life for aio.c). We also don't need
anti-recursion logics in __scm_destroy() anymore.
There is a price, though - the damn thing has become partially
asynchronous. For fput() from normal process we are guaranteed
that pending __fput() will be done before the caller returns to
userland, exits or gets stopped for ptrace.
For kernel threads and atomic contexts it's done via
schedule_work(), so theoretically we might need a way to make sure
it's finished; so far only one such place had been found, but there
might be more.
There's flush_delayed_fput() (do all pending __fput()) and there's
__fput_sync() (fput() analog doing __fput() immediately). I hope
we won't need them often; see warnings in fs/file_table.c for
details. [me, based on task_work series from Oleg merged last
cycle]
- sync series from Jan
- large part of "death to sync_supers()" work from Artem; the only
bits missing here are exofs and ext4 ones. As far as I understand,
those are going via the exofs and ext4 trees resp.; once they are
in, we can put ->write_super() to the rest, along with the thread
calling it.
- preparatory bits from unionmount series (from dhowells).
- assorted cleanups and fixes all over the place, as usual.
This is not the last pile for this cycle; there's at least jlayton's
ESTALE work and fsfreeze series (the latter - in dire need of fixes,
so I'm not sure it'll make the cut this cycle). I'll probably throw
symlink/hardlink restrictions stuff from Kees into the next pile, too.
Plus there's a lot of misc patches I hadn't thrown into that one -
it's large enough as it is..."
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (127 commits)
ext4: switch EXT4_IOC_RESIZE_FS to mnt_want_write_file()
btrfs: switch btrfs_ioctl_balance() to mnt_want_write_file()
switch dentry_open() to struct path, make it grab references itself
spufs: shift dget/mntget towards dentry_open()
zoran: don't bother with struct file * in zoran_map
ecryptfs: don't reinvent the wheels, please - use struct completion
don't expose I_NEW inodes via dentry->d_inode
tidy up namei.c a bit
unobfuscate follow_up() a bit
ext3: pass custom EOF to generic_file_llseek_size()
ext4: use core vfs llseek code for dir seeks
vfs: allow custom EOF in generic_file_llseek code
vfs: Avoid unnecessary WB_SYNC_NONE writeback during sys_sync and reorder sync passes
vfs: Remove unnecessary flushing of block devices
vfs: Make sys_sync writeout also block device inodes
vfs: Create function for iterating over block devices
vfs: Reorder operations during sys_sync
quota: Move quota syncing to ->sync_fs method
quota: Split dquot_quota_sync() to writeback and cache flushing part
vfs: Move noop_backing_dev_info check from sync into writeback
...
* ACPI conversion to PM handling based on struct dev_pm_ops.
* Conversion of a number of platform drivers to PM handling based on struct
dev_pm_ops and removal of empty legacy PM callbacks from a couple of PCI
drivers.
* Suspend-to-both for in-kernel hibernation from Bojan Smojver.
* cpuidle fixes and cleanups from ShuoX Liu, Daniel Lezcano and Preeti U Murthy.
* cpufreq bug fixes from Jonghwa Lee and Stephen Boyd.
* Suspend and hibernate fixes from Srivatsa S. Bhat and Colin Cross.
* Generic PM domains framework updates.
* RTC CMOS wakeup signaling update from Paul Fox.
* sparse warnings fixes from Sachin Kamat.
* Build warnings fixes for the generic PM domains framework and PM sysfs code.
* sysfs switch for printing device suspend times from Sameer Nanda.
* Documentation fix from Oskar Schirmer.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=vC4/
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
- ACPI conversion to PM handling based on struct dev_pm_ops.
- Conversion of a number of platform drivers to PM handling based on
struct dev_pm_ops and removal of empty legacy PM callbacks from a
couple of PCI drivers.
- Suspend-to-both for in-kernel hibernation from Bojan Smojver.
- cpuidle fixes and cleanups from ShuoX Liu, Daniel Lezcano and Preeti
Murthy.
- cpufreq bug fixes from Jonghwa Lee and Stephen Boyd.
- Suspend and hibernate fixes from Srivatsa Bhat and Colin Cross.
- Generic PM domains framework updates.
- RTC CMOS wakeup signaling update from Paul Fox.
- sparse warnings fixes from Sachin Kamat.
- Build warnings fixes for the generic PM domains framework and PM
sysfs code.
- sysfs switch for printing device suspend times from Sameer Nanda.
- Documentation fix from Oskar Schirmer.
* tag 'pm-for-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (70 commits)
cpufreq: Fix sysfs deadlock with concurrent hotplug/frequency switch
EXYNOS: bugfix on retrieving old_index from freqs.old
PM / Sleep: call early resume handlers when suspend_noirq fails
PM / QoS: Use NULL pointer instead of plain integer in qos.c
PM / QoS: Use NULL pointer instead of plain integer in pm_qos.h
PM / Sleep: Require CAP_BLOCK_SUSPEND to use wake_lock/wake_unlock
PM / Sleep: Add missing static storage class specifiers in main.c
cpuilde / ACPI: remove time from acpi_processor_cx structure
cpuidle / ACPI: remove usage from acpi_processor_cx structure
cpuidle / ACPI : remove latency_ticks from acpi_processor_cx structure
rtc-cmos: report wakeups from interrupt handler
PM / Sleep: Fix build warning in sysfs.c for CONFIG_PM_SLEEP unset
PM / Domains: Fix build warning for CONFIG_PM_RUNTIME unset
olpc-xo15-sci: Use struct dev_pm_ops for power management
PM / Domains: Replace plain integer with NULL pointer in domain.c file
PM / Domains: Add missing static storage class specifier in domain.c file
PM / crypto / ux500: Use struct dev_pm_ops for power management
PM / IPMI: Remove empty legacy PCI PM callbacks
tpm_nsc: Use struct dev_pm_ops for power management
tpm_tis: Use struct dev_pm_ops for power management
...
A few fixes plus a few features, the most generally useful thing being
the register paging support which can be used by quite a few devices:
- Support for wake IRQs in regmap-irq
- Support for register paging
- Support for explicitly specified endianness, mostly for MMIO.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=uSSe
-----END PGP SIGNATURE-----
Merge tag 'regmap-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"A few fixes plus a few features, the most generally useful thing being
the register paging support which can be used by quite a few devices:
- Support for wake IRQs in regmap-irq
- Support for register paging
- Support for explicitly specified endianness, mostly for MMIO."
* tag 'regmap-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Fix incorrect arguments to kzalloc() call
regmap: Add hook for printk logging for debugging during early init
regmap: Fix work_buf switching for page update during virtual range access.
regmap: Add support for register indirect addressing.
regmap: Move lock out from internal function _regmap_update_bits().
regmap: mmio: Staticize regmap_mmio_gen_context()
regmap: Remove warning on stubbed dev_get_regmap()
regmap: Implement support for wake IRQs
regmap: Don't try to map non-existant IRQs
regmap: Constify regmap_irq_chip
regmap: mmio: request native endian formatting
regmap: allow busses to request formatting with specific endianness
Now that scsi registers its async scan work with the async subsystem,
wait_for_device_probe() is sufficient for ensuring all scanning is
complete.
[jejb: fix merge problems with eea03c20ae Make wait_for_device_probe() also do scsi_complete_async_scans()]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Commit cf579dfb82 (PM / Sleep: Introduce
"late suspend" and "early resume" of devices) introduced a bug where
suspend_late handlers would be called, but if dpm_suspend_noirq returned
an error the early_resume handlers would never be called. All devices
would end up on the dpm_late_early_list, and would never be resumed
again.
Fix it by calling dpm_resume_early when dpm_suspend_noirq returns
an error.
Signed-off-by: Colin Cross <ccross@android.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Commit a7a20d1039 ("sd: limit the scope of the async probe domain")
make the SCSI device probing run device discovery in it's own async
domain.
However, as a result, the partition detection was no longer synchronized
by async_synchronize_full() (which, despite the name, only synchronizes
the global async space, not all of them). Which in turn meant that
"wait_for_device_probe()" would not wait for the SCSI partitions to be
parsed.
And "wait_for_device_probe()" was what the boot time init code relied on
for mounting the root filesystem.
Now, most people never noticed this, because not only is it
timing-dependent, but modern distributions all use initrd. So the root
filesystem isn't actually on a disk at all. And then before they
actually mount the final disk filesystem, they will have loaded the
scsi-wait-scan module, which not only does the expected
wait_for_device_probe(), but also does scsi_complete_async_scans().
[ Side note: scsi_complete_async_scans() had also been partially broken,
but that was fixed in commit 43a8d39d01 ("fix async probe
regression"), so that same commit a7a20d1039 had actually broken
setups even if you used scsi-wait-scan explicitly ]
Solve this problem by just moving the scsi_complete_async_scans() call
into wait_for_device_probe(). Everybody who wants to wait for device
probing to finish really wants the SCSI probing to complete, so there's
no reason not to do this.
So now "wait_for_device_probe()" really does what the name implies, and
properly waits for device probing to finish. This also removes the now
unnecessary extra calls to scsi_complete_async_scans().
Reported-and-tested-by: Artem S. Tashkinov <t.artem@mailcity.com>
Cc: Dan Williams <dan.j.williams@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <jbottomley@parallels.com>
Cc: Borislav Petkov <bp@amd64.org>
Cc: linux-scsi <linux-scsi@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* pm-sleep:
PM / Sleep: Require CAP_BLOCK_SUSPEND to use wake_lock/wake_unlock
PM / Sleep: Add missing static storage class specifiers in main.c
PM / Sleep: Fix build warning in sysfs.c for CONFIG_PM_SLEEP unset
PM / Hibernate: Print hibernation/thaw progress indicator one line at a time.
PM / Sleep: Separate printing suspend times from initcall_debug
PM / Sleep: add knob for printing device resume times
ftrace: Disable function tracing during suspend/resume and hibernation, again
PM / Hibernate: Enable suspend to both for in-kernel hibernation.
* pm-domains:
PM / Domains: Fix build warning for CONFIG_PM_RUNTIME unset
PM / Domains: Replace plain integer with NULL pointer in domain.c file
PM / Domains: Add missing static storage class specifier in domain.c file
PM / Domains: Allow device callbacks to be added at any time
PM / Domains: Add device domain data reference counter
PM / Domains: Add preliminary support for cpuidle, v2
PM / Domains: Do not stop devices after restoring their states
PM / Domains: Use subsystem runtime suspend/resume callbacks by default
Fix the following sparse warning:
drivers/base/power/qos.c:465:29: warning: Using plain integer as NULL pointer
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Fix the following sparse warnings:
drivers/base/power/main.c:48:1: warning: symbol 'dpm_prepared_list' was not declared. Should it be static?
drivers/base/power/main.c:49:1: warning: symbol 'dpm_suspended_list' was not declared. Should it be static?
drivers/base/power/main.c:50:1: warning: symbol 'dpm_late_early_list' was not declared. Should it be static?
drivers/base/power/main.c:51:1: warning: symbol 'dpm_noirq_list' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Do not send the uevent if driver_add_groups failed.
Reported-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pm_runtime_get_noresume() calls before really_probe() and
before executing __device_attach() for each driver on the
device's bus cause problems to happen if probing fails and if the
driver has enabled runtime PM for the device in its .probe()
callback. Namely, in that case, if the device has been resumed
by the driver after enabling its runtime PM and if it turns out that
.probe() should return an error, the driver is supposed to suspend
the device and disable its runtime PM before exiting .probe().
However, because the device's runtime PM usage counter was
incremented by the core before calling .probe(), the driver's attempt
to suspend the device will not succeed and the device will remain in
the full-power state after the failing .probe() has returned.
To fix this issue, remove the pm_runtime_get_noresume() calls from
driver_probe_device() and from device_attach() and replace the
corresponding pm_runtime_put_sync() calls with pm_runtime_idle()
to preserve the existing behavior (which is to check if the device
is idle and to suspend it eventually in that case after probing).
Reported-and-tested-by: Kevin Hilman <khilman@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When deferred probe was originally added the idea was that devices which
defer their probes would move themselves to the end of dpm_list in order
to try to keep the assumptions that we're making about the list being in
roughly the order things should be suspended correct. However this hasn't
been what's been happening and doing it requires a lot of duplicated code
to do the moves.
Instead take a simple, brute force solution and have the deferred probe
code push devices to the end of dpm_list before it retries the probe. This
does mean we lock the dpm_list a bit more often but it's very simple and
the code shouldn't be a fast path. We do the move with the deferred mutex
dropped since doing things with fewer locks held simultaneously seems like
a good idea.
This approach was most recently suggested by Grant Likely.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Grant Likely <grant.likely@secretlab.ca>,
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device driver attribute groups are created after userspace is notified
via an add event. Fix this by moving the kobject_uevent call to
driver_register after the attribute groups are added.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Firstly, .shutdown callback may touch a uninitialized hardware
if dev->driver is set and .probe is not completed.
Secondly, device_shutdown() may dereference a null pointer to cause
oops when dev->driver is cleared after it has been checked in
device_shutdown().
So just hold device lock and its parent lock(if it has) to
fix the races.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
all callers want the same thing, actually - a kinda-sorta analog of
kern_path_create(). I.e. they want parent vfsmount/dentry (with
->i_mutex held, to make sure the child dentry is still their child)
+ the child dentry.
Signed-off-by Al Viro <viro@zeniv.linux.org.uk>
The power/async device sysfs attribute is only used if both
CONFIG_PM_ADVANCED_DEBUG and CONFIG_PM_SLEEP are set, but the code
implementing it doesn't depend on CONFIG_PM_SLEEP. As a result, a
build warning appears if CONFIG_PM_ADVANCED_DEBUG is set and
CONFIG_PM_SLEEP is not set.
Fix it by adding a #ifdef CONFIG_PM_SLEEP around the code in
question.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The functions genpd_save_dev() and genpd_restore_dev() are not used
for CONFIG_PM_RUNTIME unset, so move them under an appropriate
#ifdef.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Fixes the following sparse warning:
drivers/base/power/domain.c:1679:55: warning: Using plain integer as NULL pointer
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Fixes the folloiwng sparse warning:
drivers/base/power/domain.c:149:5:
warning: symbol '__pm_genpd_poweron' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
On certain bios, resume hangs if cpus are allowed to enter idle states
during suspend [1].
This was fixed in apci idle driver [2].But intel_idle driver does not
have this fix. Thus instead of replicating the fix in both the idle
drivers, or in more platform specific idle drivers if needed, the
more general cpuidle infrastructure could handle this.
A suspend callback in cpuidle_driver could handle this fix. But
a cpuidle_driver provides only basic functionalities like platform idle
state detection capability and mechanisms to support entry and exit
into CPU idle states. All other cpuidle functions are found in the
cpuidle generic infrastructure for good reason that all cpuidle
drivers, irrepective of their platforms will support these functions.
One option therefore would be to register a suspend callback in cpuidle
which handles this fix. This could be called through a PM_SUSPEND_PREPARE
notifier. But this is too generic a notfier for a driver to handle.
Also, ideally the job of cpuidle is not to handle side effects of suspend.
It should expose the interfaces which "handle cpuidle 'during' suspend"
or any other operation, which the subsystems call during that respective
operation.
The fix demands that during suspend, no cpus should be allowed to enter
deep C-states. The interface cpuidle_uninstall_idle_handler() in cpuidle
ensures that. Not just that it also kicks all the cpus which are already
in idle out of their idle states which was being done during cpu hotplug
through a CPU_DYING_FROZEN callbacks.
Now the question arises about when during suspend should
cpuidle_uninstall_idle_handler() be called. Since we are dealing with
drivers it seems best to call this function during dpm_suspend().
Delaying the call till dpm_suspend_noirq() does no harm, as long as it is
before cpu_hotplug_begin() to avoid race conditions with cpu hotpulg
operations. In dpm_suspend_noirq(), it would be wise to place this call
before suspend_device_irqs() to avoid ugly interactions with the same.
Ananlogously, during resume.
References:
[1] https://bugs.launchpad.net/ubuntu/+source/linux/+bug/674075.
[2] http://marc.info/?l=linux-pm&m=133958534231884&w=2
Reported-and-tested-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Sometimes for failures during very early init the trace infrastructure
isn't available early enough to be used. For this sort of problem
defining LOG_DEVICE will add printks for basic register I/O on a specific
device, allowing trace to be extracted when the trace system doesn't come
up early enough to work with.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make it possible to modify device callbacks used by the generic PM
domains core code at any time, not only after the device has been
added to a domain. This will allow device drivers to provide their
own device PM domain callbacks even if they are registered before
adding the devices to PM domains.
For this purpose, use the observation that the struct
generic_pm_domain_data object containing the relevant callback
pointers may be allocated by pm_genpd_add_callbacks() and the
callbacks may be set before __pm_genpd_add_device() is run for
the given device. This object will then be used by
__pm_genpd_add_device(), but it has to be protected from
premature removal by reference counting.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add a mechanism for counting references to the
struct generic_pm_domain_data object pointed to by
dev->power.subsys_data->domain_data if the device in question
belongs to a generic PM domain.
This change is necessary for a subsequent patch making it possible to
allocate that object from within pm_genpd_add_callbacks(), so that
drivers can attach their PM domain device callbacks to devices before
those devices are added to PM domains.
This patch has been tested on the SH7372 Mackerel board.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This picks up the big printk fixes, and resolves a merge issue with:
drivers/extcon/extcon_gpio.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some systems there are CPU cores located in the same power
domains as I/O devices. Then, power can only be removed from the
domain if all I/O devices in it are not in use and the CPU core
is idle. Add preliminary support for that to the generic PM domains
framework.
First, the platform is expected to provide a cpuidle driver with one
extra state designated for use with the generic PM domains code.
This state should be initially disabled and its exit_latency value
should be set to whatever time is needed to bring up the CPU core
itself after restoring power to it, not including the domain's
power on latency. Its .enter() callback should point to a procedure
that will remove power from the domain containing the CPU core at
the end of the CPU power transition.
The remaining characteristics of the extra cpuidle state, referred to
as the "domain" cpuidle state below, (e.g. power usage, target
residency) should be populated in accordance with the properties of
the hardware.
Next, the platform should execute genpd_attach_cpuidle() on the PM
domain containing the CPU core. That will cause the generic PM
domains framework to treat that domain in a special way such that:
* When all devices in the domain have been suspended and it is about
to be turned off, the states of the devices will be saved, but
power will not be removed from the domain. Instead, the "domain"
cpuidle state will be enabled so that power can be removed from
the domain when the CPU core is idle and the state has been chosen
as the target by the cpuidle governor.
* When the first I/O device in the domain is resumed and
__pm_genpd_poweron(() is called for the first time after
power has been removed from the domain, the "domain" cpuidle
state will be disabled to avoid subsequent surprise power removals
via cpuidle.
The effective exit_latency value of the "domain" cpuidle state
depends on the time needed to bring up the CPU core itself after
restoring power to it as well as on the power on latency of the
domain containing the CPU core. Thus the "domain" cpuidle state's
exit_latency has to be recomputed every time the domain's power on
latency is updated, which may happen every time power is restored
to the domain, if the measured power on latency is greater than
the latency stored in the corresponding generic_pm_domain structure.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Kevin Hilman <khilman@ti.com>
While resuming a device belonging to a PM domain,
pm_genpd_runtime_resume() calls __pm_genpd_restore_device() to
restore its state, if necessary. The latter starts the device,
using genpd_start_dev(), restores its state, using
genpd_restore_dev(), and then stops it, using genpd_stop_dev().
However, this last operation is not necessary, because the
device is supposed to be operational after pm_genpd_runtime_resume()
has returned and because of it pm_genpd_runtime_resume() has to
call genpd_start_dev() once again for the "restored" device, which
is inefficient.
To make things more efficient, remove the call to genpd_stop_dev()
from __pm_genpd_restore_device() and the direct call to
genpd_start_dev() from pm_genpd_runtime_resume(). [Of course,
genpd_start_dev() still has to be called by it for devices with the
power.irq_safe flag set, because __pm_genpd_restore_device() is not
executed for them.]
This change has been tested on the SH7372 Mackerel board.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Currently, the default "save state" and "restore state" routines
for generic PM domains, pm_genpd_default_save_state() and
pm_genpd_default_restore_state(), respectively, only use runtime PM
callbacks provided by device drivers, but in general those callbacks
need not provide the entire necessary functionality. Namely, in
general it may be necessary to execute subsystem (i.e. device type,
device class or bus type) callbacks that will carry out all of the
necessary operations.
For this reason, modify pm_genpd_default_save_state() and
pm_genpd_default_restore_state() to execute subsystem callbacks,
if they are provided, and fall back to driver callbacks otherwise.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Change the behavior of the newly introduced
/sys/power/pm_print_times attribute so that its initial value
depends on initcall_debug, but setting it to 0 will cause device
suspend/resume times not to be printed, even if initcall_debug has
been set. This way, the people who use initcall_debug for reasons
other than PM debugging will be able to switch the suspend/resume
times printing off, if need be.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added a new knob called /sys/power/pm_print_times. Setting it to 1
enables printing of time taken by devices to suspend and resume.
Setting it to 0 disables this printing (unless overridden by
initcall_debug kernel command line option).
Signed-off-by: Sameer Nanda <snanda@chromium.org>
Acked-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
__device_suspend() must always send a completion. Otherwise, parent
devices will wait forever.
Commit 1e2ef05b, "PM: Limit race conditions between runtime PM and
system sleep (v2)", introduced a regression by short-circuiting the
complete_all() for certain error cases.
This patch fixes the bug by always signalling a completion.
Addresses http://crosbug.com/31972
Tested by injecting an abort.
Signed-off-by: Mandeep Singh Baines <msb@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Here are some fixes for 3.5-rc4 that resolve the kmsg problems that
people have reported showing up after the printk and kmsg changes went
into 3.5-rc1. There are also a smattering of other tiny fixes for the
extcon and hyper-v drivers that people have reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk/iNQcACgkQMUfUDdst+yklTQCfZCXFlhA43bZo/8Joqd2pLIIW
2uoAoMze0SlfJeN6Qu7yY0P+qV/f/pc3
=UNFY
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and printk fixes from Greg Kroah-Hartman:
"Here are some fixes for 3.5-rc4 that resolve the kmsg problems that
people have reported showing up after the printk and kmsg changes went
into 3.5-rc1. There are also a smattering of other tiny fixes for the
extcon and hyper-v drivers that people have reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
extcon: max8997: Add missing kfree for info->edev in max8997_muic_remove()
extcon: Set platform drvdata in gpio_extcon_probe() and fix irq leak
extcon: Fix wrong index in max8997_extcon_cable[]
kmsg - kmsg_dump() fix CONFIG_PRINTK=n compilation
printk: return -EINVAL if the message len is bigger than the buf size
printk: use mutex lock to stop syslog_seq from going wild
kmsg - kmsg_dump() use iterator to receive log buffer content
vme: change maintainer e-mail address
Extcon: Don't try to create duplicate link names
driver core: fixup reversed deferred probe order
printk: Fix alignment of buf causing crash on ARM EABI
Tools: hv: verify origin of netlink connector message
After page update, orginal work_buf has to be restored regardless of
the result.
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Devices with register paging or indirectly accessed registers can configure
register mapping to map those on virtual address range. During access to
virtually mapped register range, indirect addressing is processed
automatically, in following steps:
1. selector for page or indirect register is updated (when needed);
2. register in data window is accessed.
Configuration should provide minimum and maximum register for virtual range,
details of selector field for page selection, minimum and maximum register of
data window for indirect access.
Virtual range registers are managed by cache as well as direct access
registers. In order to make indirect access more efficient, selector register
should be declared as non-volatile, if possible.
struct regmap_config is extended with the following:
struct regmap_range_cfg *ranges;
unsigned int n_ranges;
[Also reordered debugfs init to later on since the cleanup code was
conflicting with the new cleanup code for ranges anyway -- broonie]
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Locks are moved to regmap_update_bits(), which allows to reenter internal
function _regmap_update_bits() from inside of regmap read/write routines.
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix kernel-doc warnings in drivers/base/dma*.c:
Warning(drivers/base/dma-buf.c:498): No description found for parameter 'vaddr'
Warning(drivers/base/dma-coherent.c:199): No description found for parameter 'ret'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1) drvdata is for a driver to store a pointer to driver specific data
2) If no driver is bound, there is no driver specific data associated with
the device
3) Thus logically drvdata should be NULL if no driver is bound.
But many drivers don't clear drvdata on device_release, or set drvdata
early on in probe and leave it set on probe error. Both of which results
in a dangling pointer in drvdata.
This patch enforce for drvdata to be NULL after device_release or on probe
failure.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If driver requests probe deferral,
it will be added to deferred_probe_pending_list
by driver_deferred_probe_add(), but, it used list_add().
Because of that, deferred probe will be run as reversed order.
This patch uses list_add_tail(), and solved this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
regmap_mmio_gen_context() is only used in regmap-mmio.c. Thus make it static.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If !dev->class, device_move() does not respect the dpm_order.
Fix it to do so.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
[Fixed a small dangling label compile warning]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow chips to provide a bank of registers for controlling the wake state
in a similar fashion to the masks and propagate the wake count to the
parent interrupt controller.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the driver supplied an empty entry in the array of IRQs then return
an error rather than trying to do the mapping. This is intended for use
with handling chip variants and similar situations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The word to be transmitted/received via regmap is composed by the following
parts:
config->reg_bits
config->val_bits
config->pad_bits
,so the total size should be calculated by summing up the number of bits of
each element and using a DIV_ROUND_UP to return the number of bytes.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If debugfs isn't cleaned up, stale files will be left in the filesystem
which will cause an OOPS when accessed the first time, and hang the
accessing application when accessed again, presumably due to some lock
being left held.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This will avoid the regmap core converting all addresses and values into
big endian, only for the mmio bus driver to have to convert them back to
native endian.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a field to struct regmap_bus that allows bus drivers to request that
register addresses and values be formatted with a specific endianness.
The default endianness is unchanged from current operation: Big.
Implement native endian formatting/parsing for 16- and 32-bit values.
This will be enough to support regmap-mmio.c.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pull vfs changes from Al Viro.
"A lot of misc stuff. The obvious groups:
* Miklos' atomic_open series; kills the damn abuse of
->d_revalidate() by NFS, which was the major stumbling block for
all work in that area.
* ripping security_file_mmap() and dealing with deadlocks in the
area; sanitizing the neighborhood of vm_mmap()/vm_munmap() in
general.
* ->encode_fh() switched to saner API; insane fake dentry in
mm/cleancache.c gone.
* assorted annotations in fs (endianness, __user)
* parts of Artem's ->s_dirty work (jff2 and reiserfs parts)
* ->update_time() work from Josef.
* other bits and pieces all over the place.
Normally it would've been in two or three pull requests, but
signal.git stuff had eaten a lot of time during this cycle ;-/"
Fix up trivial conflicts in Documentation/filesystems/vfs.txt (the
'truncate_range' inode method was removed by the VM changes, the VFS
update adds an 'update_time()' method), and in fs/btrfs/ulist.[ch] (due
to sparse fix added twice, with other changes nearby).
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (95 commits)
nfs: don't open in ->d_revalidate
vfs: retry last component if opening stale dentry
vfs: nameidata_to_filp(): don't throw away file on error
vfs: nameidata_to_filp(): inline __dentry_open()
vfs: do_dentry_open(): don't put filp
vfs: split __dentry_open()
vfs: do_last() common post lookup
vfs: do_last(): add audit_inode before open
vfs: do_last(): only return EISDIR for O_CREAT
vfs: do_last(): check LOOKUP_DIRECTORY
vfs: do_last(): make ENOENT exit RCU safe
vfs: make follow_link check RCU safe
vfs: do_last(): use inode variable
vfs: do_last(): inline walk_component()
vfs: do_last(): make exit RCU safe
vfs: split do_lookup()
Btrfs: move over to use ->update_time
fs: introduce inode operation ->update_time
reiserfs: get rid of resierfs_sync_super
reiserfs: mark the superblock as dirty a bit later
...
Since there are uses for I2C_M_NOSTART which are much more sensible and
standard than most of the protocol mangling functionality (the main one
being gather writes to devices where something like a register address
needs to be inserted before a block of data) create a new I2C_FUNC_NOSTART
for this feature and update all the users to use it.
Also strengthen the disrecommendation of the protocol mangling while we're
at it.
In the case of regmap-i2c we remove the requirement for mangling as
I2C_M_NOSTART is the only mangling feature which is being used.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
/sys/devices/system/node/{online,possible} outputs a garbage byte
because print_nodes_state() returns content size + 1. To fix the bug,
the patch changes the use of cpuset_sprintf_cpulist to follow the use at
other places, which is clearer and safer.
This bug was introduced in v2.6.24 (commit bde631a51876: "mm: add node
states sysfs class attributeS").
Signed-off-by: Ryota Ozaki <ozaki.ryota@gmail.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPvzQCAAoJEFErWKtxJpJdpNEIAI1sKDywvfuJK0Ik76ICj1Yt
P//4/ZvROmT8w9u/Jw3BAG7K3u7NLtfht6RcrUFqMULjMUUQ/aymlY9uTbwFZ+so
WCsVh5tHCULa1oUnAUv8fGMgvGoufD4ZqI/9qbuYLmBtUwPAatul51cEmQyWVvLa
lJN8PzJ7whfYqNoXpR4SCp8eHY4iJ3DZFDhypdQfZbTgOTrzsoVIJnTdHUXsiRQQ
E3gB2dRvyihzOD/UFac47af5wVUwtvo1N6NdQ5tJxOX9ZhVGdHaxAqF5FTlWpm6F
uK100uqFHPbm/TZGtSrGD1ai8L7Hbl//LuzaODjLH9usCiYe6KzSSwf8Alg59Ws=
=hsWu
-----END PGP SIGNATURE-----
Merge tag 'tag-for-linus-3.5' of git://git.linaro.org/people/sumitsemwal/linux-dma-buf
Pull dma-buf updates from Sumit Semwal:
"Here's the first signed-tag pull request for dma-buf framework. It
includes the following key items:
- mmap support
- vmap support
- related documentation updates
These are needed by various drivers to allow mmap/vmap of dma-buf
shared buffers. Dave Airlie has some prime patches dependent on the
vmap pull as well."
* tag 'tag-for-linus-3.5' of git://git.linaro.org/people/sumitsemwal/linux-dma-buf:
dma-buf: add initial vmap documentation
dma-buf: minor documentation fixes.
dma-buf: add vmap interface
dma-buf: mmap support
Pull CMA and ARM DMA-mapping updates from Marek Szyprowski:
"These patches contain two major updates for DMA mapping subsystem
(mainly for ARM architecture). First one is Contiguous Memory
Allocator (CMA) which makes it possible for device drivers to allocate
big contiguous chunks of memory after the system has booted.
The main difference from the similar frameworks is the fact that CMA
allows to transparently reuse the memory region reserved for the big
chunk allocation as a system memory, so no memory is wasted when no
big chunk is allocated. Once the alloc request is issued, the
framework migrates system pages to create space for the required big
chunk of physically contiguous memory.
For more information one can refer to nice LWN articles:
- 'A reworked contiguous memory allocator':
http://lwn.net/Articles/447405/
- 'CMA and ARM':
http://lwn.net/Articles/450286/
- 'A deep dive into CMA':
http://lwn.net/Articles/486301/
- and the following thread with the patches and links to all previous
versions:
https://lkml.org/lkml/2012/4/3/204
The main client for this new framework is ARM DMA-mapping subsystem.
The second part provides a complete redesign in ARM DMA-mapping
subsystem. The core implementation has been changed to use common
struct dma_map_ops based infrastructure with the recent updates for
new dma attributes merged in v3.4-rc2. This allows to use more than
one implementation of dma-mapping calls and change/select them on the
struct device basis. The first client of this new infractructure is
dmabounce implementation which has been completely cut out of the
core, common code.
The last patch of this redesign update introduces a new, experimental
implementation of dma-mapping calls on top of generic IOMMU framework.
This lets ARM sub-platform to transparently use IOMMU for DMA-mapping
calls if one provides required IOMMU hardware.
For more information please refer to the following thread:
http://www.spinics.net/lists/arm-kernel/msg175729.html
The last patch merges changes from both updates and provides a
resolution for the conflicts which cannot be avoided when patches have
been applied on the same files (mainly arch/arm/mm/dma-mapping.c)."
Acked by Andrew Morton <akpm@linux-foundation.org>:
"Yup, this one please. It's had much work, plenty of review and I
think even Russell is happy with it."
* 'for-linus' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping: (28 commits)
ARM: dma-mapping: use PMD size for section unmap
cma: fix migration mode
ARM: integrate CMA with DMA-mapping subsystem
X86: integrate CMA with DMA-mapping subsystem
drivers: add Contiguous Memory Allocator
mm: trigger page reclaim in alloc_contig_range() to stabilise watermarks
mm: extract reclaim code from __alloc_pages_direct_reclaim()
mm: Serialize access to min_free_kbytes
mm: page_isolation: MIGRATE_CMA isolation functions added
mm: mmzone: MIGRATE_CMA migration type added
mm: page_alloc: change fallbacks array handling
mm: page_alloc: introduce alloc_contig_range()
mm: compaction: export some of the functions
mm: compaction: introduce isolate_freepages_range()
mm: compaction: introduce map_pages()
mm: compaction: introduce isolate_migratepages_range()
mm: page_alloc: remove trailing whitespace
ARM: dma-mapping: add support for IOMMU mapper
ARM: dma-mapping: use alloc, mmap, free from dma_ops
ARM: dma-mapping: remove redundant code and do the cleanup
...
Conflicts:
arch/x86/include/asm/dma-mapping.h
Some minor inline documentation fixes for gaps resulting from new patches.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
The main requirement I have for this interface is for scanning out
using the USB gpu devices. Since these devices have to read the
framebuffer on updates and linearly compress it, using kmaps
is a major overhead for every update.
v2: fix warn issues pointed out by Sylwester Nawrocki.
v3: fix compile !CONFIG_DMA_SHARED_BUFFER and add _GPL for now
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Rob Clark <rob.clark@linaro.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Compared to Rob Clark's RFC I've ditched the prepare/finish hooks
and corresponding ioctls on the dma_buf file. The major reason for
that is that many people seem to be under the impression that this is
also for synchronization with outstanding asynchronous processsing.
I'm pretty massively opposed to this because:
- It boils down reinventing a new rather general-purpose userspace
synchronization interface. If we look at things like futexes, this
is hard to get right.
- Furthermore a lot of kernel code has to interact with this
synchronization primitive. This smells a look like the dri1 hw_lock,
a horror show I prefer not to reinvent.
- Even more fun is that multiple different subsystems would interact
here, so we have plenty of opportunities to create funny deadlock
scenarios.
I think synchronization is a wholesale different problem from data
sharing and should be tackled as an orthogonal problem.
Now we could demand that prepare/finish may only ensure cache
coherency (as Rob intended), but that runs up into the next problem:
We not only need mmap support to facilitate sw-only processing nodes
in a pipeline (without jumping through hoops by importing the dma_buf
into some sw-access only importer), which allows for a nicer
ION->dma-buf upgrade path for existing Android userspace. We also need
mmap support for existing importing subsystems to support existing
userspace libraries. And a loot of these subsystems are expected to
export coherent userspace mappings.
So prepare/finish can only ever be optional and the exporter /needs/
to support coherent mappings. Given that mmap access is always
somewhat fallback-y in nature I've decided to drop this optimization,
instead of just making it optional. If we demonstrate a clear need for
this, supported by benchmark results, we can always add it in again
later as an optional extension.
Other differences compared to Rob's RFC is the above mentioned support
for mapping a dma-buf through facilities provided by the importer.
Which results in mmap support no longer being optional.
Note that this dma-buf mmap patch does _not_ support every possible
insanity an existing subsystem could pull of with mmap: Because it
does not allow to intercept pagefaults and shoot down ptes importing
subsystems can't add some magic of their own at these points (e.g. to
automatically synchronize with outstanding rendering or set up some
special resources). I've done a cursory read through a few mmap
implementions of various subsytems and I'm hopeful that we can avoid
this (and the complexity it'd bring with it).
Additonally I've extended the documentation a bit to explain the hows
and whys of this mmap extension.
In case we ever want to add support for explicitly cache maneged
userspace mmap with a prepare/finish ioctl pair, we could specify that
userspace needs to mmap a different part of the dma_buf, e.g. the
range starting at dma_buf->size up to dma_buf->size*2. This works
because the size of a dma_buf is invariant over it's lifetime. The
exporter would obviously need to fall back to coherent mappings for
both ranges if a legacy clients maps the coherent range and the
architecture cannot suppor conflicting caching policies. Also, this
would obviously be optional and userspace needs to be able to fall
back to coherent mappings.
v2:
- Spelling fixes from Rob Clark.
- Compile fix for !DMA_BUF from Rob Clark.
- Extend commit message to explain how explicitly cache managed mmap
support could be added later.
- Extend the documentation with implementations notes for exporters
that need to manually fake coherency.
v3:
- dma_buf pointer initialization goof-up noticed by Rebecca Schultz
Zavin.
Cc: Rob Clark <rob.clark@linaro.org>
Cc: Rebecca Schultz Zavin <rebecca@android.com>
Acked-by: Rob Clark <rob.clark@linaro.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
* Implementation of opportunistic suspend (autosleep) and user space interface
for manipulating wakeup sources.
* Hibernate updates from Bojan Smojver and Minho Ban.
* Updates of the runtime PM core and generic PM domains framework related to
PM QoS.
* Assorted fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQIcBAABAgAGBQJPu+jwAAoJEKhOf7ml8uNsOw0P/0w1FqXD64a1laE43JIlBe9w
yHEcLHc9MXN+8lS0XQ6jFiL/VC3U5Sj7Ro+DFKcL2MWX//dfDcZcwA9ep/qh4tHV
tJ987IijdWqJV14pde3xQafhp/9i12rArLxns7S5fzkdfVk0iDjhZZaZy4afFJYM
SuCsDhCwWefZh89+oLikByiFPnhW+f2ZC9YQeokBM/XvZLtxmOiVfL6duloT/Cr+
58jkrJ8xz/5kmmN4bXM4Wlpf9ZIYFXbvtbKrq3GZOXc+LpNKlWQyFgg/pIuxBewC
uSgsNXXV0LFDi5JfER/8l9MMLtJwwc4VHzpLvMnRv+GtwO2/FKIIr9Fcv000IL2N
0/Ppr52M7XpRruM/k+YroUQ4F1oBX6HB4e3rwqC+XG6n5bwn/Jc7kdy7aUojqNLG
Nlr5f0vBjLTSF66Jnel71Bn+gbA1ogER7E+esSTMpyX+RgGJAUVt5oX9IjbXl3PI
bk8xW1csSRxBI2NkFOd9EM3vMzdGc5uu+iOoy7iBvcAK0AEfo2Ml9YuSVFQeqAu0
A96MUW155A+GKMC7I/LK8pTgMvYDedWhVW9uyXpMRjwdFC5/ywZU1aM00tL9HMpG
pzHOFJgsYrf/6VCV8BwqgudRYd0K5EPSGeITCg973os/XzJIOCfJuy+Pn5V/F0ew
lTbi8ipQD0Hh8A/Xt0QB
=Q2vo
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
- Implementation of opportunistic suspend (autosleep) and user space
interface for manipulating wakeup sources.
- Hibernate updates from Bojan Smojver and Minho Ban.
- Updates of the runtime PM core and generic PM domains framework
related to PM QoS.
- Assorted fixes.
* tag 'pm-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (25 commits)
epoll: Fix user space breakage related to EPOLLWAKEUP
PM / Domains: Make it possible to add devices to inactive domains
PM / Hibernate: Use get_gendisk to verify partition if resume_file is integer format
PM / Domains: Fix computation of maximum domain off time
PM / Domains: Fix link checking when add subdomain
PM / Sleep: User space wakeup sources garbage collector Kconfig option
PM / Sleep: Make the limit of user space wakeup sources configurable
PM / Documentation: suspend-and-cpuhotplug.txt: Fix typo
PM / Domains: Cache device stop and domain power off governor results, v3
PM / Domains: Make device removal more straightforward
PM / Sleep: Fix a mistake in a conditional in autosleep_store()
epoll: Add a flag, EPOLLWAKEUP, to prevent suspend while epoll events are ready
PM / QoS: Create device constraints objects on notifier registration
PM / Runtime: Remove device fields related to suspend time, v2
PM / Domains: Rework default domain power off governor function, v2
PM / Domains: Rework default device stop governor function, v2
PM / Sleep: Add user space interface for manipulating wakeup sources, v3
PM / Sleep: Add "prevent autosleep time" statistics to wakeup sources
PM / Sleep: Implement opportunistic sleep, v2
PM / Sleep: Add wakeup_source_activate and wakeup_source_deactivate tracepoints
...
Fixes a missing select from the Palmas driver a bit more throoughly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJPvK0PAAoJEBus8iNuMP3d370QAJ4UcCCB0qba+py+4ZC/P2CL
LPTXV0OMv0FJVJtnE2VGVe/QKxxE62unIC1wSRE/g1WamcEsCPBmKRZPdL4P67r1
TEZ4aSiyS71KVezfgXqBvNZxMmYglBtq1y8YR+v6RkZSJ1jdpSBDtbHA0uPj/cpG
S7nzcpJLbmR/R+Qd3AJt2gAGszQgfM8YH+2uLqjnNUUoKpW4mmxoX3V8ddo9D6/O
D4nfk9VTGlGtZBUkHYbF+C+GLCqWDQp3nSUvW01vqQF4pBve5ErXKkQL495srTDr
0p94CMaxq0byQZdiVnxij5e82amDzjphflNwynC+ht09FFCYKgiFgbFsICiQvS+H
xhO6G10cRS+sFpKX0Ex4Y8EofisrzHxT1gHiaCwpCT86jpaKU6IATA0m9cH3xaFA
yiFtgBgRD1KDrfSUfYA9XyvidDah4Y1ZUE5+09G2vYbQyQaa+o+lEYnO3R9pyr5H
3Tn0AH8lGAug8M2V/5l48DtCEs4r03OJ7Wrfvak6tWWXiIsjRo6zaKZKnXTkVpTn
bFDx4tgSA/3nF46SHMBBZclAhmF/c3skLMqwoH84iicIfW6x2boXHGP60o5UDdPc
ED4RYvNDEtvqxsJBlJUxPSJRIaXl9kEMleyIflcoKPv22UohStyNalsT7tjopC49
RW8bbnCOEP8vYE5ORgYu
=kkX0
-----END PGP SIGNATURE-----
Merge tag 'regmap-domain-deps' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull a regmap kconfig dependency fix from Mark Brown:
"Fix the dependency on IRQ_DOMAIN for REGMAP_IRQ in the core
Fixes a missing select from the Palmas driver a bit more throoughly."
* tag 'regmap-domain-deps' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Use select .. if to get IRQ_DOMAIN enabled
Ensure that we can't get randconfig breakage by doing the IRQ_DOMAIN
select automatically. Don't just do the select from REGMAP_IRQ to ensure
that the select actually gets noticed.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Pull scheduler changes from Ingo Molnar:
"The biggest change is the cleanup/simplification of the load-balancer:
instead of the current practice of architectures twiddling scheduler
internal data structures and providing the scheduler domains in
colorfully inconsistent ways, we now have generic scheduler code in
kernel/sched/core.c:sched_init_numa() that looks at the architecture's
node_distance() parameters and (while not fully trusting it) deducts a
NUMA topology from it.
This inevitably changes balancing behavior - hopefully for the better.
There are various smaller optimizations, cleanups and fixlets as well"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Taint kernel with TAINT_WARN after sleep-in-atomic bug
sched: Remove stale power aware scheduling remnants and dysfunctional knobs
sched/debug: Fix printing large integers on 32-bit platforms
sched/fair: Improve the ->group_imb logic
sched/nohz: Fix rq->cpu_load[] calculations
sched/numa: Don't scale the imbalance
sched/fair: Revert sched-domain iteration breakage
sched/x86: Rewrite set_cpu_sibling_map()
sched/numa: Fix the new NUMA topology bits
sched/numa: Rewrite the CONFIG_NUMA sched domain support
sched/fair: Propagate 'struct lb_env' usage into find_busiest_group
sched/fair: Add some serialization to the sched_domain load-balance walk
sched/fair: Let minimally loaded cpu balance the group
sched: Change rq->nr_running to unsigned int
x86/numa: Check for nonsensical topologies on real hw as well
x86/numa: Hard partition cpu topology masks on node boundaries
x86/numa: Allow specifying node_distance() for numa=fake
x86/sched: Make mwait_usable() heed to "idle=" kernel parameters properly
sched: Update documentation and comments
sched_rt: Avoid unnecessary dequeue and enqueue of pushable tasks in set_cpus_allowed_rt()
Here's the driver core, and other driver subsystems, pull request for
the 3.5-rc1 merge window.
Outside of a few minor driver core changes, we ended up with the
following different subsystem and core changes as well, due to
interdependancies on the driver core:
- hyperv driver updates
- drivers/memory being created and some drivers moved into it
- extcon driver subsystem created out of the old Android staging switch
driver code
- dynamic debug updates
- printk rework, and /dev/kmsg changes
All of this has been tested in the linux-next releases for a few weeks
with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+7q28ACgkQMUfUDdst+ykXmwCfcPASzC+/bDkuqdWsqzxlWZ7+
VOQAnAriySv397St36J6Hz5bMQZwB1Yq
=SQc+
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here's the driver core, and other driver subsystems, pull request for
the 3.5-rc1 merge window.
Outside of a few minor driver core changes, we ended up with the
following different subsystem and core changes as well, due to
interdependancies on the driver core:
- hyperv driver updates
- drivers/memory being created and some drivers moved into it
- extcon driver subsystem created out of the old Android staging
switch driver code
- dynamic debug updates
- printk rework, and /dev/kmsg changes
All of this has been tested in the linux-next releases for a few weeks
with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fix up conflicts in drivers/extcon/extcon-max8997.c where git noticed
that a patch to the deleted drivers/misc/max8997-muic.c driver needs to
be applied to this one.
* tag 'driver-core-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (90 commits)
uio_pdrv_genirq: get irq through platform resource if not set otherwise
memory: tegra{20,30}-mc: Remove empty *_remove()
printk() - isolate KERN_CONT users from ordinary complete lines
sysfs: get rid of some lockdep false positives
Drivers: hv: util: Properly handle version negotiations.
Drivers: hv: Get rid of an unnecessary check in vmbus_prep_negotiate_resp()
memory: tegra{20,30}-mc: Use dev_err_ratelimited()
driver core: Add dev_*_ratelimited() family
Driver Core: don't oops with unregistered driver in driver_find_device()
printk() - restore prefix/timestamp printing for multi-newline strings
printk: add stub for prepend_timestamp()
ARM: tegra30: Make MC optional in Kconfig
ARM: tegra20: Make MC optional in Kconfig
ARM: tegra30: MC: Remove unnecessary BUG*()
ARM: tegra20: MC: Remove unnecessary BUG*()
printk: correctly align __log_buf
ARM: tegra30: Add Tegra Memory Controller(MC) driver
ARM: tegra20: Add Tegra Memory Controller(MC) driver
printk() - restore timestamp printing at console output
printk() - do not merge continuation lines of different threads
...
The Contiguous Memory Allocator is a set of helper functions for DMA
mapping framework that improves allocations of contiguous memory chunks.
CMA grabs memory on system boot, marks it with MIGRATE_CMA migrate type
and gives back to the system. Kernel is allowed to allocate only movable
pages within CMA's managed memory so that it can be used for example for
page cache when DMA mapping do not use it. On
dma_alloc_from_contiguous() request such pages are migrated out of CMA
area to free required contiguous block and fulfill the request. This
allows to allocate large contiguous chunks of memory at any time
assuming that there is enough free memory available in the system.
This code is heavily based on earlier works by Michal Nazarewicz.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Rob Clark <rob.clark@linaro.org>
Tested-by: Ohad Ben-Cohen <ohad@wizery.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
Tested-by: Barry Song <Baohua.Song@csr.com>
Add a common helper for dma-mapping core for mapping a coherent buffer
to userspace.
Reported-by: Subash Patel <subashrp@gmail.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-By: Subash Patel <subash.ramaswamy@linaro.org>
The generic PM domains core code currently requires domains to be in
the "power on" state for adding devices to them, but this limitation
turns out to be inconvenient in some situations, so remove it.
For this purpose, make __pm_genpd_add_device() set the device's
need_restore flag if the domain is in the "power off" state, so that
the device's "restore state" (usually .runtime_resume()) callback
is executed when it is resumed after the domain has been turned on.
If the domain is in the "power on" state, the device's need_restore
flag will be cleared by __pm_genpd_add_device(), so that its "save
state" (usually .runtime_suspend()) callback is executed when the
domain is about to be turned off. However, since that default
behavior need not be always desirable, add a helper function
pm_genpd_dev_need_restore() allowing a device's need_restore flag
to be set/unset at any time.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
It's been broken forever (i.e. it's not scheduling in a power
aware fashion), as reported by Suresh and others sending
patches, and nobody cares enough to fix it properly ...
so remove it to make space free for something better.
There's various problems with the code as it stands today, first
and foremost the user interface which is bound to topology
levels and has multiple values per level. This results in a
state explosion which the administrator or distro needs to
master and almost nobody does.
Furthermore large configuration state spaces aren't good, it
means the thing doesn't just work right because it's either
under so many impossibe to meet constraints, or even if
there's an achievable state workloads have to be aware of
it precisely and can never meet it for dynamic workloads.
So pushing this kind of decision to user-space was a bad idea
even with a single knob - it's exponentially worse with knobs
on every node of the topology.
There is a proposal to replace the user interface with a single
3 state knob:
sched_balance_policy := { performance, power, auto }
where 'auto' would be the preferred default which looks at things
like Battery/AC mode and possible cpufreq state or whatever the hw
exposes to show us power use expectations - but there's been no
progress on it in the past many months.
Aside from that, the actual implementation of the various knobs
is known to be broken. There have been sporadic attempts at
fixing things but these always stop short of reaching a mergable
state.
Therefore this wholesale removal with the hopes of spurring
people who care to come forward once again and work on a
coherent replacement.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Cc: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1326104915.2442.53.camel@twins
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In some chips the IRQ status registers are not contiguous in the register
map but spaced at even spaces. This is an easy case to handle with minor
changes. It is assume for this purpose that the stride for status is
equal to the stride for mask/ack registers as well.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
driver_find_device() can be called with an unregistered driver. Need
to check driver_private to see if it's populated or not, especially
under deferrable probe.
In the case that there are 2 drivers, one depends on the other. With
-EPROBE_DEFER, two drivers can use deferred probe to ensure that their
relative probe order doesn't matter. If dependee driver is probed
first, then the dependant's driver_find_device('dependee')
succeeds. If the dependant is probed first, then the dependant's
driver_find_device('dependee') should return NULL, and the dependant
should get -EPROBE_DEFER. driver_find_device() needs to return NULL if
it's not populated.
In [PATCHv5 2/3] ARM: tegra: Add SMMU enabler in AHB:
http://article.gmane.org/gmane.linux.ports.tegra/4658
"tegra_ahb_driver" may not be populated when it's called.
For more SMMU/AHB specific discussion, refer to the following thread:
https://lkml.org/lkml/2012/5/10/21
Signed-off-by: Hiroshi DOYU <hdoyu@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This gets us up to date with the recommended current kernel infrastructure
and should transparently give us device tree interrupt bindings for any
devices using the framework. If an explicit IRQ mapping is passed in then
a legacy interrupt range is created, otherwise a simple linear mapping is
used. Previously a mapping was mandatory so existing drivers should not
be affected.
A function regmap_irq_get_virq() is provided to allow drivers to map
individual IRQs which should be used in preference to the existing
regmap_irq_chip_get_base() which is only valid if a legacy IRQ range is
provided.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is a last minute bug fix that was only just noticed since the code
path that's being exercised here is one that is fairly rarely used. The
changelog for the change itself is extremely clear and the code itself
is obvious to inspection so should be pretty safe.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xcal
-----END PGP SIGNATURE-----
Merge tag 'regmap-3.4' into regmap-stride
regmap: Last minute bug fix for 3.4
This is a last minute bug fix that was only just noticed since the code
path that's being exercised here is one that is fairly rarely used. The
changelog for the change itself is extremely clear and the code itself
is obvious to inspection so should be pretty safe.
Conflicts:
drivers/base/regmap/regmap.c (overlap between the fix and stride code)
* pm-sleep:
PM / Sleep: User space wakeup sources garbage collector Kconfig option
PM / Sleep: Make the limit of user space wakeup sources configurable
PM / Documentation: suspend-and-cpuhotplug.txt: Fix typo
PM / Sleep: Fix a mistake in a conditional in autosleep_store()
epoll: Add a flag, EPOLLWAKEUP, to prevent suspend while epoll events are ready
PM / Sleep: Add user space interface for manipulating wakeup sources, v3
PM / Sleep: Add "prevent autosleep time" statistics to wakeup sources
PM / Sleep: Implement opportunistic sleep, v2
PM / Sleep: Add wakeup_source_activate and wakeup_source_deactivate tracepoints
PM / Sleep: Change wakeup source statistics to follow Android
PM / Sleep: Use wait queue to signal "no wakeup events in progress"
PM / Sleep: Look for wakeup events in later stages of device suspend
PM / Hibernate: Hibernate/thaw fixes/improvements
The default domain power off governor function for generic PM
domains, default_power_down_ok(), may violate subdomain maximum
off time limit by allowing the master domain to be off for too
long. Namely, it only finds the minium of all device maximum
off times over the domain's devices and uses that to compute the
domain's maximum off time, but it should do the same for the
subdomains.
Fix this problem by modifying default_power_down_ok() to compute
the given domain's maximum off time as the difference between the
minimum off time over all devices and subdomains in the domain and
its power on latency.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Current pm_genpd_add_subdomain() will allow duplicated link between
master and slave domain. This patch fixed it.
Because when current pm_genpd_add_subdomain() checks whether the link
between the master and slave generic PM domain already exists,
slave_links instead of master_links of master domain is used.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The function regmap_bulk_read() calls the regmap_read() for
each register if set of register has volatile and cache is
enabled. In this case, last few register read makes the memory
corruption if the register size is not the size of unsigned int.
The regam_read() takes argument as unsigned int for returning
value and it update the value as
*val = map->format.parse_val(map->work_buf);
This causes complete 4 bytes (size of unsigned int) to get written.
Now if client pass the memory pointer for value which is equal to the
required size of register count in regmap_bulk_read() then last few
register read actually update the memory beyond passed pointer size.
Avoid this by using local variable for read and then do memcpy()
for actual byte copy to passed pointer based on register size.
I allocated one pointer ptr and take first 16 bytes dump of that
pointer then call regmap_bulk_read() with pointer which is just
on top of this allocated pointer and register count of 128. Here
register size is 1 byte.
The memory trace of last 5 register read are as follows:
[ 5.438589] regmap_bulk_read after regamp_read() for register 122
[ 5.447421] 0xef993c20 0xef993c00 0x00000000 0x00000001
[ 5.467535] regmap_bulk_read after regamp_read() for register 123
[ 5.476374] 0xef993c20 0xef993c00 0x00000000 0x00000001
[ 5.496425] regmap_bulk_read after regamp_read() for register 124
[ 5.505260] 0xef993c20 0xef993c00 0x00000000 0x00000001
[ 5.525372] regmap_bulk_read after regamp_read() for register 125
[ 5.534205] 0xef993c00 0xef993c00 0x00000000 0x00000001
[ 5.554258] regmap_bulk_read after regamp_read() for register 126
[ 5.563100] 0xef990000 0xef993c00 0x00000000 0x00000001
[ 5.554258] regmap_bulk_read after regamp_read() for register 127
[ 5.587108] 0xef000000 0xef993c00 0x00000000 0x00000001
Here it is observed that the memory content at first word started changing
on last 3 regmap_read() and so corruption happened.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use devres to implement dev_get_regmap(). This should mean that in almost
all cases devices wishing to take advantage of framework features based on
regmap shouldn't need to explicitly pass the regmap into the framework.
This simplifies device setup a bit.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Extends dev_printk() to attach a dictionary with a device identifier
and the driver core subsystem name to logged messages, which makes
dev_prink() reliable machine-readable. In addition to the printed
plain text message, it creates these properties:
SUBSYSTEM= - the driver-core subsytem name
DEVICE=
b12:8 - block dev_t
c127:3 - char dev_t
n8 - netdev ifindex
+sound:card0 - subsystem:devname
Tested-by: William Douglas <william.douglas@intel.com>
Signed-off-by: Kay Sievers <kay@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The results of the default device stop and domain power off governor
functions for generic PM domains, default_stop_ok() and
default_power_down_ok(), depend only on the timing data of devices,
which are static, and on their PM QoS constraints. Thus, in theory,
these functions only need to carry out their computations, which may
be time consuming in general, when it is known that the PM QoS
constraint of at least one of the devices in question has changed.
Use the PM QoS notifiers of devices to implement that. First,
introduce new fields, constraint_changed and max_off_time_changed,
into struct gpd_timing_data and struct generic_pm_domain,
respectively, and register a PM QoS notifier function when adding
a device into a domain that will set those fields to 'true' whenever
the device's PM QoS constraint is modified. Second, make
default_stop_ok() and default_power_down_ok() use those fields to
decide whether or not to carry out their computations from scratch.
The device and PM domain hierarchies are taken into account in that
and the expense is that the changes of PM QoS constraints of
suspended devices will not be taken into account immediately, which
isn't guaranteed anyway in general.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The removal of a device from a PM domain doesn't have to browse
the domain's device list, because it can check directly if the
device belongs to the given domain. Moreover, it should clear
the domain_data pointer in dev->power.subsys_data, because
dev_pm_put_subsys_data(dev) may not remove dev->power.subsys_data
and the stale domain data pointer may cause problems to happen.
Rework pm_genpd_remove_device() taking the above observations into
account.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
APIs using devres frequently want to implement a "remove and free the
resource" operation so it seems sensible that they should be able to
just have devres do the freeing for them since that's a big part of what
devres is all about.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's not massively obvious (at least to me) that removing and freeing a
resource does not involve calling the release function for the resource
but rather only removes the management of it. Make the documentation more
explicit.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was done to resolve a merge issue with the init/main.c file.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current behavior of dev_pm_qos_add_notifier() makes device PM QoS
notifiers less than useful. Namely, it silently returns success when
called before any PM QoS constraints are added for the device, so the
caller will assume that the notifier has been registered, but when
someone actually adds some nontrivial constraints for the device
eventually, the previous callers of dev_pm_qos_add_notifier()
will not know about that and their notifier routines will not be
executed (contrary to their expectations).
To address this problem make dev_pm_qos_add_notifier() create the
constraints object for the device if it is not present when the
routine is called.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by : markgross <markgross@thegnar.org>
After the previous changes in default_stop_ok() and
default_power_down_ok() for PM domains, there are two fields in
struct dev_pm_info that aren't necessary any more, suspend_time
and max_time_suspended_ns.
Remove those fields along with all of the code that accesses them,
which simplifies the runtime PM framework quite a bit.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The existing default domain power down governor function for PM
domains, default_power_down_ok(), is supposed to check whether or not
the PM QoS latency constraints of the devices in the domain will be
violated if the domain is turned off by pm_genpd_poweroff().
However, the computations carried out by it don't reflect the
definition of the PM QoS latency constrait in
Documentation/ABI/testing/sysfs-devices-power.
Make default_power_down_ok() follow the definition of the PM QoS
latency constrait. In particular, make it only take latencies into
account, because it doesn't matter how much time has elapsed since
the domain's devices were suspended for the computation.
Remove the break_even_ns and power_off_time fields from
struct generic_pm_domain, because they are not necessary any more.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The existing default device stop governor function for PM domains,
default_stop_ok(), is supposed to check whether or not the device's
PM QoS latency constraint will be violated if the device is stopped
by pm_genpd_runtime_suspend(). However, the computations carried out
by it don't reflect the definition of the PM QoS latency constrait in
Documentation/ABI/testing/sysfs-devices-power.
Make default_stop_ok() follow the definition of the PM QoS latency
constrait. In particular, make it take the device's start and stop
latencies correctly.
Add a new field, effective_constraint_ns, to struct gpd_timing_data
and use it to store the difference between the device's PM QoS
constraint and its resume latency for use by the device's parent
(the effective_constraint_ns values for the children are used for
computing the parent's one along with its PM QoS constraint).
Remove the break_even_ns field from struct gpd_timing_data, because
it's not used any more.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Android allows user space to manipulate wakelocks using two
sysfs file located in /sys/power/, wake_lock and wake_unlock.
Writing a wakelock name and optionally a timeout to the wake_lock
file causes the wakelock whose name was written to be acquired (it
is created before is necessary), optionally with the given timeout.
Writing the name of a wakelock to wake_unlock causes that wakelock
to be released.
Implement an analogous interface for user space using wakeup sources.
Add the /sys/power/wake_lock and /sys/power/wake_unlock files
allowing user space to create, activate and deactivate wakeup
sources, such that writing a name and optionally a timeout to
wake_lock causes the wakeup source of that name to be activated,
optionally with the given timeout. If that wakeup source doesn't
exist, it will be created and then activated. Writing a name to
wake_unlock causes the wakeup source of that name, if there is one,
to be deactivated. Wakeup sources created with the help of
wake_lock that haven't been used for more than 5 minutes are garbage
collected and destroyed. Moreover, there can be only WL_NUMBER_LIMIT
wakeup sources created with the help of wake_lock present at a time.
The data type used to track wakeup sources created by user space is
called "struct wakelock" to indicate the origins of this feature.
This version of the patch includes an rbtree manipulation fix from John Stultz.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: NeilBrown <neilb@suse.de>
Android uses one wakelock statistics that is only necessary for
opportunistic sleep. Namely, the prevent_suspend_time field
accumulates the total time the given wakelock has been locked
while "automatic suspend" was enabled. Add an analogous field,
prevent_sleep_time, to wakeup sources and make it behave in a similar
way.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce a mechanism by which the kernel can trigger global
transitions to a sleep state chosen by user space if there are no
active wakeup sources.
It consists of a new sysfs attribute, /sys/power/autosleep, that
can be written one of the strings returned by reads from
/sys/power/state, an ordered workqueue and a work item carrying out
the "suspend" operations. If a string representing the system's
sleep state is written to /sys/power/autosleep, the work item
triggering transitions to that state is queued up and it requeues
itself after every execution until user space writes "off" to
/sys/power/autosleep.
That work item enables the detection of wakeup events using the
functions already defined in drivers/base/power/wakeup.c (with one
small modification) and calls either pm_suspend(), or hibernate() to
put the system into a sleep state. If a wakeup event is reported
while the transition is in progress, it will abort the transition and
the "system suspend" work item will be queued up again.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: NeilBrown <neilb@suse.de>
Add tracepoints to wakeup_source_activate and wakeup_source_deactivate.
Useful for checking that specific wakeup sources overlap as expected.
Signed-off-by: Arve Hjønnevåg <arve@android.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Wakeup statistics used by Android are slightly different from what we
have in wakeup sources at the moment and there aren't any known
users of those statistics other than Android, so modify them to make
it easier for Android to switch to wakeup sources.
This removes the struct wakeup_source's hit_cout field, which is very
rough and therefore not very useful, and adds two new fields,
wakeup_count and expire_count. The first one tracks how many times
the wakeup source is activated with events_check_enabled set (which
roughly corresponds to the situations when a system power transition
to a sleep state is in progress and would be aborted by this wakeup
source if it were the only active one at that time) and the second
one is the number of times the wakeup source has been activated with
a timeout that expired.
Additionally, the last_time field is now updated when the wakeup
source is deactivated too (previously it was only updated during
the wakeup source's activation), which seems to be what Android does
with the analogous counter for wakelocks.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current wakeup source deactivation code doesn't do anything when
the counter of wakeup events in progress goes down to zero, which
requires pm_get_wakeup_count() to poll that counter periodically.
Although this reduces the average time it takes to deactivate a
wakeup source, it also may lead to a substantial amount of unnecessary
polling if there are extended periods of wakeup activity. Thus it
seems reasonable to use a wait queue for signaling the "no wakeup
events in progress" condition and remove the polling.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: mark gross <markgross@thegnar.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the device suspend code in drivers/base/power/main.c
only checks if there have been any wakeup events, and therefore the
ongoing system transition to a sleep state should be aborted, during
the first (i.e. "suspend") device suspend phase. However, wakeup
events may be reported later as well, so it's reasonable to look for
them in the in the subsequent (i.e. "late suspend" and "suspend
noirq") phases.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the use_single_rw flag for devices that use format_write() since
format_write() doesn't support any form of block operation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some devices does not support bulk read and write operations, for them
we have series of single write and read operations.
Signed-off-by: Anthony Olech <Anthony.Olech@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
[Fixed coding style, don't check use_single_rw before assign --broonie ]
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we don't have a cached value for a register and we can cache it then
when we do a read a value we should add it to the cache to save rereading
it later on. Do this for single register reads, for block reads the code
would be a little more complex and this covers most practical usage.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This reverts commit a15d49fd30 as that
patch broke the build.
Cc: Hannes Reinecke <hare@suse.de>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
klist_iter_init_node() takes a node as a start argument.
However, this node might not be valid anymore.
This patch updates the klist_iter_init_node() and
dependent functions to return an error if so.
All calling functions have been audited to check
for a return code here.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: Greg Kroah-Hartmann <gregkh@linuxfoundation.org>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Stable Kernel <stable@kernel.org>
Cc: Linux Kernel <linux-kernel@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable 'system_kset' is only referenced in this file and
should be marked static to prevent it from being exposed globally.
This quiets the sparse waring:
warning: symbol 'system_kset' was not declared. Should it be static?
Also, remove the comment since drivers/base/sys.c has now been
deleted.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix kernel-doc warnings in dma-buf.c:
Warning(drivers/base/dma-buf.c:305): No description found for parameter 'dmabuf'
Warning(drivers/base/dma-buf.c:305): Excess function parameter 'dma_buf' description in 'dma_buf_begin_cpu_access'
Warning(drivers/base/dma-buf.c:332): No description found for parameter 'dmabuf'
Warning(drivers/base/dma-buf.c:332): Excess function parameter 'dma_buf' description in 'dma_buf_end_cpu_access'
Warning(drivers/base/dma-buf.c:350): No description found for parameter 'dmabuf'
Warning(drivers/base/dma-buf.c:350): Excess function parameter 'dma_buf' description in 'dma_buf_kmap_atomic'
Warning(drivers/base/dma-buf.c:367): No description found for parameter 'dmabuf'
Warning(drivers/base/dma-buf.c:367): Excess function parameter 'dma_buf' description in 'dma_buf_kunmap_atomic'
Warning(drivers/base/dma-buf.c:385): No description found for parameter 'dmabuf'
Warning(drivers/base/dma-buf.c:385): Excess function parameter 'dma_buf' description in 'dma_buf_kmap'
Warning(drivers/base/dma-buf.c:402): No description found for parameter 'dmabuf'
Warning(drivers/base/dma-buf.c:402): Excess function parameter 'dma_buf' description in 'dma_buf_kunmap'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f01ee60fff ("regmap: implement register striding") caused the
compile errors below. Fix them.
drivers/base/regmap/regmap-irq.c: In function 'regmap_irq_sync_unlock':
drivers/base/regmap/regmap-irq.c:62:12: error: 'map' undeclared (first use in this function)
drivers/base/regmap/regmap-irq.c:62:12: note: each undeclared identifier is reported only once for each function it appears in
drivers/base/regmap/regmap-irq.c: In function 'regmap_irq_enable':
drivers/base/regmap/regmap-irq.c:77:37: error: 'map' undeclared (first use in this function)
drivers/base/regmap/regmap-irq.c: In function 'regmap_irq_disable':
drivers/base/regmap/regmap-irq.c:85:37: error: 'map' undeclared (first use in this function)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
regmap_config.reg_stride is introduced. All extant register addresses
are a multiple of this value. Users of serial-oriented regmap busses will
typically set this to 1. Users of the MMIO regmap bus will typically set
this based on the value size of their registers, in bytes, so 4 for a
32-bit register.
Throughout the regmap code, actual register addresses are used. Wherever
the register address is used to index some array of values, the address
is divided by the stride to determine the index, or vice-versa. Error-
checking is added to all entry-points for register address data to ensure
that register addresses actually satisfy the specified stride. The MMIO
bus ensures that the specified stride is large enough for the register
size.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 79c64d5 "regmap: allow regmap instances to be named" changed the
prototype of regmap_debugfs_init, but didn't update the dummy inline used
when !CONFIG_DEBUGFS. Fix this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some devices have multiple separate register regions. Logically, one
regmap would be created per region. One issue that prevents this is that
each instance will attempt to create the same debugfs files. Avoid this
by allowing regmaps to be named, and use the name to construct the
debugfs directory name.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This fixes:
note: expected ‘struct ida *’ but argument is of type ‘struct idr *’
warning: passing argument 1 of ‘ida_pre_get’ from incompatible pointer type
Reported-by: Arnd Bergman <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
soc_lock is already initialized by DEFINE_SPINLOCK.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two more small fixes:
- Now we have users for it that aren't running Android it turns out that
regcache_sync_region() is much more useful to drivers if it's exported
for use by modules. Who knew?
- Make sure we don't divide by zero when doing debugfs dumps of rbtrees,
not visible up until now because everything was providing at least
some cache on startup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=qm1Q
-----END PGP SIGNATURE-----
Merge tag 'regmap-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull two more small regmap fixes from Mark Brown:
- Now we have users for it that aren't running Android it turns out
that regcache_sync_region() is much more useful to drivers if it's
exported for use by modules. Who knew?
- Make sure we don't divide by zero when doing debugfs dumps of
rbtrees, not visible up until now because everything was providing at
least some cache on startup.
* tag 'regmap-3.4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: prevent division by zero in rbtree_show
regmap: Export regcache_sync_region()
val_len should be a multiple of val_bytes. If it's not, error out early.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
These error checks are implemented in regmap core. Remove the duplicate
code from regmap-mmio.c
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some of the error conditions detected by regmap_mmio_*() are pure internal
errors, rather than user-/client-triggerable conditions. Convert these to
BUG().
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is a basic memory-mapped-IO bus for regmap. It has the following
features and limitations:
* Registers themselves may be 8, 16, 32, or 64-bit. 64-bit is only
supported on 64-bit platforms.
* Register offsets are limited to precisely 32-bit.
* IO is performed using readl/writel, with no provision for using the
__raw_readl or readl_relaxed variants.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some bus types have very fast IO. For these, acquiring a mutex for every
IO operation is a significant overhead. Allow busses to indicate their IO
is fast, and enhance regmap to use a spinlock for those busses.
[Currently limited to native endian registers -- broonie]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The only context needed by I2C and SPI bus definitions is the device
itself; this can be converted to an i2c_client or spi_device in order
to perform IO on the device. However, other bus types may need more
context in order to perform IO. Enable this by having regmap_init accept
a bus_context parameter, and pass this to all bus callbacks. The
existing callbacks simply pass the struct device here. Future bus types
may pass something else.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Merge batch of fixes from Andrew Morton:
"The simple_open() cleanup was held back while I wanted for laggards to
merge things.
I still need to send a few checkpoint/restore patches. I've been
wobbly about merging them because I'm wobbly about the overall
prospects for success of the project. But after speaking with Pavel
at the LSF conference, it sounds like they're further toward
completion than I feared - apparently davem is at the "has stopped
complaining" stage regarding the net changes. So I need to go back
and re-review those patchs and their (lengthy) discussion."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (16 patches)
memcg swap: use mem_cgroup_uncharge_swap fix
backlight: add driver for DA9052/53 PMIC v1
C6X: use set_current_blocked() and block_sigmask()
MAINTAINERS: add entry for sparse checker
MAINTAINERS: fix REMOTEPROC F: typo
alpha: use set_current_blocked() and block_sigmask()
simple_open: automatically convert to simple_open()
scripts/coccinelle/api/simple_open.cocci: semantic patch for simple_open()
libfs: add simple_open()
hugetlbfs: remove unregister_filesystem() when initializing module
drivers/rtc/rtc-88pm860x.c: fix rtc irq enable callback
fs/xattr.c:setxattr(): improve handling of allocation failures
fs/xattr.c:listxattr(): fall back to vmalloc() if kmalloc() failed
fs/xattr.c: suppress page allocation failure warnings from sys_listxattr()
sysrq: use SEND_SIG_FORCED instead of force_sig()
proc: fix mount -t proc -o AAA
Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op. This leads to a
proliferation of the default_open() implementation across the entire
tree.
Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().
This replacement was done with the following semantic patch:
<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}
@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If there are no nodes in the cache, nodes will be 0, so calculating
"registers / nodes" will cause division by zero.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Fixes mostly, including:
* Patch series that hopefully fixes races between the freezer and request_firmware()
and request_firmware_nowait() for good, with two cleanups from Stephen Boyd on top.
* Runtime PM fix from Alan Stern preventing tasks from getting stuck indefinitely
in the runtime PM wait queue.
* Device PM QoS update from MyungJoo Ham introducing a new variant of
pm_qos_update_request() allowing the callers to specify a timeout.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=ligR
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.4-part-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
- Patch series that hopefully fixes races between the freezer and
request_firmware() and request_firmware_nowait() for good, with two
cleanups from Stephen Boyd on top.
- Runtime PM fix from Alan Stern preventing tasks from getting stuck
indefinitely in the runtime PM wait queue.
- Device PM QoS update from MyungJoo Ham introducing a new variant of
pm_qos_update_request() allowing the callers to specify a timeout.
* tag 'pm-for-3.4-part-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / QoS: add pm_qos_update_request_timeout() API
firmware_class: Move request_firmware_nowait() to workqueues
firmware_class: Reorganize fw_create_instance()
PM / Sleep: Mitigate race between the freezer and request_firmware()
PM / Sleep: Move disabling of usermode helpers to the freezer
PM / Hibernate: Disable usermode helpers right before freezing tasks
firmware_class: Do not warn that system is not ready from async loads
firmware_class: Split _request_firmware() into three functions, v2
firmware_class: Rework usermodehelper check
PM / Runtime: don't forget to wake up waitqueue on failure
regcache_sync_region() isn't going to be useful to most drivers if we
don't export it since otherwise they can't use it when built modular.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This change combines any padding bits into the register address bits when
determining register format handlers to use the next byte-divisible
register size.
A reg_shift member is introduced to the regmap struct to enable fixup
of the reg format.
Format handlers now take an extra parameter specifying the number of
bits to shift the value by.
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for devices with 24 data bits.
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The code currently passes the register offset in the current block to
regcache_lookup_reg. This works fine as long as there is only one block and with
base register of 0, but in all other cases it will look-up the default for a
wrong register, which can cause unnecessary register writes. This patch fixes
it by passing the actual register number to regcache_lookup_reg.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: <stable@vger.kernel.org>
Pull dma-buf updates from Sumit Semwal:
"This includes the following key items:
- kernel cpu access support,
- flag-passing to dma_buf_fd,
- relevant Documentation updates, and
- some minor cleanups and fixes.
These changes are needed for the drm prime/dma-buf interface code that
Dave Airlie plans to submit in this merge window."
* 'for-linus-3.4' of git://git.linaro.org/people/sumitsemwal/linux-dma-buf:
dma-buf: correct dummy function declarations.
dma-buf: document fd flags and O_CLOEXEC requirement
dma_buf: Add documentation for the new cpu access support
dma-buf: add support for kernel cpu access
dma-buf: don't hold the mutex around map/unmap calls
dma-buf: add get_dma_buf()
dma-buf: pass flags into dma_buf_fd.
dma-buf: add dma_data_direction to unmap dma_buf_op
dma-buf: Move code out of mutex-protected section in dma_buf_attach()
dma-buf: Return error instead of using a goto statement when possible
dma-buf: Remove unneeded sanity checks
dma-buf: Constify ops argument to dma_buf_export()
Oddly enough a work_struct was already part of the firmware_work
structure but nobody was using it. Instead of creating a new
kthread for each request_firmware_nowait() call just schedule the
work on the system workqueue. This should avoid some overhead
in forking new threads when they're not strictly necessary.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Recent patches to split up the three phases of request_firmware()
lead to a casting away of const in fw_create_instance(). We can
avoid this cast by splitting up fw_create_instance() a bit.
Make _request_firmware_setup() return a struct fw_priv and use
that struct instead of passing struct firmware to
_request_firmware(). Move the uevent and device file creation
bits to the loading phase and rename the function to
_request_firmware_load() to better reflect its purpose.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
If firmware is requested asynchronously, by calling
request_firmware_nowait(), there is no reason to fail the request
(and warn the user) when the system is (presumably temporarily)
unready to handle it (because user space is not available yet or
frozen). For this reason, introduce an alternative routine for
read-locking umhelper_sem, usermodehelper_read_lock_wait(), that
will wait for usermodehelper_disabled to be unset (possibly with
a timeout) and make request_firmware_work_func() use it instead of
usermodehelper_read_trylock().
Accordingly, modify request_firmware() so that it uses
usermodehelper_read_trylock() to acquire umhelper_sem and remove
the code related to that lock from _request_firmware().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
Split _request_firmware() into three functions,
_request_firmware_prepare() doing preparatory work that need not be
done under umhelper_sem, _request_firmware_cleanup() doing the
post-error cleanup and _request_firmware() carrying out the remaining
operations.
This change is requisite for moving the acquisition of umhelper_sem
from _request_firmware() to the callers, which is going to be done
subsequently.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: stable@vger.kernel.org
Instead of two functions, read_lock_usermodehelper() and
usermodehelper_is_disabled(), used in combination, introduce
usermodehelper_read_trylock() that will only return with umhelper_sem
held if usermodehelper_disabled is unset (and will return -EAGAIN
otherwise) and make _request_firmware() use it.
Rename read_unlock_usermodehelper() to
usermodehelper_read_unlock() to follow the naming convention of the
new function.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
This patch (as1535) fixes a bug in the runtime PM core. When a
runtime suspend attempt completes, whether successfully or not, the
device's power.wait_queue is supposed to be signalled. But this
doesn't happen in the failure pathway of rpm_suspend() when another
autosuspend attempt is rescheduled. As a result, a task can get stuck
indefinitely on the wait queue (I have seen this happen in testing).
The patch fixes the problem by moving the wake_up_all() call up near
the start of the failure code.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Big differences to other contenders in the field (like ion) is
that this also supports highmem, so we have to split up the cpu
access from the kernel side into a prepare and a kmap step.
Prepare is allowed to fail and should do everything required so that
the kmap calls can succeed (like swapin/backing storage allocation,
flushing, ...).
More in-depth explanations will follow in the follow-up documentation
patch.
Changes in v2:
- Clear up begin_cpu_access confusion noticed by Sumit Semwal.
- Don't automatically fallback from the _atomic variants to the
non-atomic variants. The _atomic callbacks are not allowed to
sleep, so we want exporters to make this decision explicit. The
function signatures are explicit, so simpler exporters can still
use the same function for both.
- Make the unmap functions optional. Simpler exporters with permanent
mappings don't need to do anything at unmap time.
Changes in v3:
- Adjust the WARN_ON checks for the new ->ops functions as suggested
by Rob Clark and Sumit Semwal.
- Rebased on top of latest dma-buf-next git.
Changes in v4:
- Fixup a missing - in a return -EINVAL; statement.
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
The mutex protects the attachment list and hence needs to be held
around the callbakc to the exporters (optional) attach/detach
functions.
Holding the mutex around the map/unmap calls doesn't protect any
dma_buf state. Exporters need to properly protect any of their own
state anyway (to protect against calls from their own interfaces).
So this only makes the locking messier (and lockdep easier to anger).
Therefore let's just drop this.
v2: Rebased on top of latest dma-buf-next git.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rob Clark <rob.clark@linaro.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
We need to pass the flags into dma_buf_fd at this point,
so the flags end up doing the right thing for O_CLOEXEC.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Some exporters may use DMA map/unmap APIs in dma-buf ops, which require
enum dma_data_direction for both map and unmap operations.
Thus, the unmap dma_buf_op also needs to have enum dma_data_direction as
a parameter.
Reported-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
"[RFC PATCH 0/2] audit of linux/device.h users in include/*"
https://lkml.org/lkml/2012/3/4/159
--
Nearly every subsystem has some kind of header with a proto like:
void foo(struct device *dev);
and yet there is no reason for most of these guys to care about the
sub fields within the device struct. This allows us to significantly
reduce the scope of headers including headers. For this instance, a
reduction of about 40% is achieved by replacing the include with the
simple fact that the device is some kind of a struct.
Unlike the much larger module.h cleanup, this one is simply two
commits. One to fix the implicit <linux/device.h> users, and then
one to delete the device.h includes from the linux/include/ dir
wherever possible.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3j4+
-----END PGP SIGNATURE-----
Merge tag 'device-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull <linux/device.h> avoidance patches from Paul Gortmaker:
"Nearly every subsystem has some kind of header with a proto like:
void foo(struct device *dev);
and yet there is no reason for most of these guys to care about the
sub fields within the device struct. This allows us to significantly
reduce the scope of headers including headers. For this instance, a
reduction of about 40% is achieved by replacing the include with the
simple fact that the device is some kind of a struct.
Unlike the much larger module.h cleanup, this one is simply two
commits. One to fix the implicit <linux/device.h> users, and then one
to delete the device.h includes from the linux/include/ dir wherever
possible."
* tag 'device-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
device.h: audit and cleanup users in main include dir
device.h: cleanup users outside of linux/include (C files)
Remove for_each_set_bit_cont() after confirming that no one uses
for_each_set_bit_cont() anymore.
[sfr@canb.auug.org.au: regmap: cope with bitops API change]
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
seeing a trickle of new features coming in they're getting much smaller
than they were. It's also nice to have some features which support
other subsystems building infrastructure on top of regmap. Highlights
include:
- Support for padding between the register and the value when
interacting with the device, sometimes needed for fast interfaces.
- Support for applying register updates to the device when restoring the
register state. This is intended to be used to apply updates supplied by
manufacturers for tuning the performance of the device (many of which
are to undocumented registers which aren't otherwise covered).
- Support for multi-register operations on cached registers.
- Support for syncing only part of the register cache.
- Stubs and parameter query functions intended to make it easier for other
subsystems to build infrastructure on top of the regmap API.
plus a few driver updates making use of the new features which it was
easier to merge via this tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4Eo9
-----END PGP SIGNATURE-----
Merge tag 'regmap-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"Things are really quieting down with the regmap API, while we're still
seeing a trickle of new features coming in they're getting much
smaller than they were. It's also nice to have some features which
support other subsystems building infrastructure on top of regmap.
Highlights include:
- Support for padding between the register and the value when
interacting with the device, sometimes needed for fast interfaces.
- Support for applying register updates to the device when restoring
the register state. This is intended to be used to apply updates
supplied by manufacturers for tuning the performance of the device
(many of which are to undocumented registers which aren't otherwise
covered).
- Support for multi-register operations on cached registers.
- Support for syncing only part of the register cache.
- Stubs and parameter query functions intended to make it easier for
other subsystems to build infrastructure on top of the regmap API.
plus a few driver updates making use of the new features which it was
easier to merge via this tree."
* tag 'regmap-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap: (41 commits)
regmap: Fix future missing prototype of devres_alloc() and friends
regmap: Rejig struct declarations for stubbed API
regmap: Fix rbtree block base in sync
regcache: Make sure we sync register 0 in an rbtree cache
regmap: delete unused module.h from drivers/base/regmap files
regmap: Add stub for regcache_sync_region()
mfd: Improve performance of later WM1811 revisions
regmap: Fix x86_64 breakage
regmap: Allow drivers to sync only part of the register cache
regmap: Supply ranges to the sync operations
regmap: Add tracepoints for cache only and cache bypass
regmap: Mark the cache as clean after a successful sync
regmap: Remove default cache sync implementation
regmap: Skip hardware defaults for LZO caches
regmap: Expose the driver name in debugfs
mfd: wm8400: Convert to devm_regmap_init_i2c()
mfd: wm831x: Convert to devm_regmap_init()
mfd: wm8994: Convert to devm_regmap_init()
mfd/ASoC: Convert WM8994 driver to use regmap patches
mfd: Add __devinit and __devexit annotations in wm8994
...
Here is the first big update chunk of sound stuff for 3.4-rc1.
In the common sound infrastructure, there are a few changes for
dynamic PCM support (used in ASoC) and a few clean-ups. Majority of
changes are found, as usual, in HD-audio and ASoC.
Some highlights of HD-audio changes:
- All the long-standing static quirk codes for Realtek codec were
finally removed by fixing and extending the Realtek auto-parser.
- The mute-LED control is standardized over all HD-audio codec
drivers using the extended vmaster hook.
- The vmaster slave mixer elements are initialized to 0dB as default
so that the user won't be annoyed by the silent output after
updates, e.g. due to the additions of new elements.
- Other many fix-ups for the misc HD-audio devices.
In the ASoC side, this is a very active release, including a quite a
few framework enhancements. Some highlights:
- Support for widgets not associated with a CODEC, an important part
of the dynamic PCM framework.
- A library factoring out the common code shared by dmaengine based
DMA drivers contributed by Lars-Peter Clausen. This will save a lot
of code and make it much easier to deploy enhancements to
dmaengine.
- Support for binary controls, used for providing runtime
configuration of algorithm coefficients.
- A new DAPM widget type for regulator supplies allowing drivers for
devices that can power down unused supplies while active to do
without any per-driver code.
- DAPM widgets for DAIs, initially giving a speed boost for playback
startup and shutdown and also the basis for CODEC<->CODEC DAI link
support.
- Support for specifying the number of significant bits on audio
interfaces, useful for allowing applications to know how much effort
to put into generating data for a larger sample format.
- Conversion of the FSI driver used on some SH processors to
DMAEngine.
- Conversion of EP93xx drivers to DMAEngine.
- New CODEC drivers for Maxim MAX9768 and Wolfson Microelectronics
WM2200.
- Move audmux driver from arc/arm to sound/soc
- McBSP move from arch/ to sound/ and updates
Also, a few small updates and fixes for other drivers like au88x0,
ymfpci, USB 6fire, USB usx2yaudio are included.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=5FJq
-----END PGP SIGNATURE-----
Merge tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull updates of sound stuff from Takashi Iwai:
"Here is the first big update chunk of sound stuff for 3.4-rc1.
In the common sound infrastructure, there are a few changes for
dynamic PCM support (used in ASoC) and a few clean-ups. Majority of
changes are found, as usual, in HD-audio and ASoC.
Some highlights of HD-audio changes:
- All the long-standing static quirk codes for Realtek codec were
finally removed by fixing and extending the Realtek auto-parser.
- The mute-LED control is standardized over all HD-audio codec
drivers using the extended vmaster hook.
- The vmaster slave mixer elements are initialized to 0dB as default
so that the user won't be annoyed by the silent output after
updates, e.g. due to the additions of new elements.
- Other many fix-ups for the misc HD-audio devices.
In the ASoC side, this is a very active release, including a quite a
few framework enhancements. Some highlights:
- Support for widgets not associated with a CODEC, an important part
of the dynamic PCM framework.
- A library factoring out the common code shared by dmaengine based
DMA drivers contributed by Lars-Peter Clausen. This will save a
lot of code and make it much easier to deploy enhancements to
dmaengine.
- Support for binary controls, used for providing runtime
configuration of algorithm coefficients.
- A new DAPM widget type for regulator supplies allowing drivers for
devices that can power down unused supplies while active to do
without any per-driver code.
- DAPM widgets for DAIs, initially giving a speed boost for playback
startup and shutdown and also the basis for CODEC<->CODEC DAI link
support.
- Support for specifying the number of significant bits on audio
interfaces, useful for allowing applications to know how much
effort to put into generating data for a larger sample format.
- Conversion of the FSI driver used on some SH processors to
DMAEngine.
- Conversion of EP93xx drivers to DMAEngine.
- New CODEC drivers for Maxim MAX9768 and Wolfson Microelectronics
WM2200.
- Move audmux driver from arc/arm to sound/soc
- McBSP move from arch/ to sound/ and updates
Also, a few small updates and fixes for other drivers like au88x0,
ymfpci, USB 6fire, USB usx2yaudio are included."
* tag 'sound-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (446 commits)
ASoC: wm8994: Provide VMID mode control and fix default sequence
ASoC: wm8994: Add missing break in resume
ASoC: wm_hubs: Don't actively manage LINEOUT_VMID_BUF
ASoC: pxa-ssp: atomically set stream active masks
ASoC: fsl: p1022ds: tell the WM8776 codec driver that it's the master
ASoC: Samsung: Added to support mono recording
ALSA: hda - Fix build with CONFIG_PM=n
ALSA: au88x0 - Avoid possible Oops at unbinding
ALSA: usb-audio - Fix build error by consitification of rate list
ASoC: core: Fix obscure leak of runtime array
ALSA: pcm - Avoid GFP_ATOMIC in snd_pcm_link()
ALSA: pcm: Constify the list in snd_pcm_hw_constraint_list
ASoC: wm8996: Add 44.1kHz support
ALSA: hda - Fix build of patch_sigmatel.c without CONFIG_SND_HDA_POWER_SAVE
ASoC: mx27vis-aic32x4: Convert it to platform driver
ALSA: hda - fix printing of high HDMI sample rates
ALSA: ymfpci - Fix legacy registers on S3/S4 resume
ALSA: control - Fixe a trailing white space error
ALSA: hda - Add expose_enum_ctl flag to snd_hda_add_vmaster_hook()
ALSA: hda - Add "Mute-LED Mode" enum control
...
Pull MCE changes from Ingo Molnar.
* 'x86-mce-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Fix return value of mce_chrdev_read() when erst is disabled
x86/mce: Convert static array of pointers to per-cpu variables
x86/mce: Replace hard coded hex constants with symbolic defines
x86/mce: Recognise machine check bank signature for data path error
x86/mce: Handle "action required" errors
x86/mce: Add mechanism to safely save information in MCE handler
x86/mce: Create helper function to save addr/misc when needed
HWPOISON: Add code to handle "action required" errors.
HWPOISON: Clean up memory_failure() vs. __memory_failure()
Pull powerpc merge from Benjamin Herrenschmidt:
"Here's the powerpc batch for this merge window. It is going to be a
bit more nasty than usual as in touching things outside of
arch/powerpc mostly due to the big iSeriesectomy :-) We finally got
rid of the bugger (legacy iSeries support) which was a PITA to
maintain and that nobody really used anymore.
Here are some of the highlights:
- Legacy iSeries is gone. Thanks Stephen ! There's still some bits
and pieces remaining if you do a grep -ir series arch/powerpc but
they are harmless and will be removed in the next few weeks
hopefully.
- The 'fadump' functionality (Firmware Assisted Dump) replaces the
previous (equivalent) "pHyp assisted dump"... it's a rewrite of a
mechanism to get the hypervisor to do crash dumps on pSeries, the
new implementation hopefully being much more reliable. Thanks
Mahesh Salgaonkar.
- The "EEH" code (pSeries PCI error handling & recovery) got a big
spring cleaning, motivated by the need to be able to implement a
new backend for it on top of some new different type of firwmare.
The work isn't complete yet, but a good chunk of the cleanups is
there. Note that this adds a field to struct device_node which is
not very nice and which Grant objects to. I will have a patch soon
that moves that to a powerpc private data structure (hopefully
before rc1) and we'll improve things further later on (hopefully
getting rid of the need for that pointer completely). Thanks Gavin
Shan.
- I dug into our exception & interrupt handling code to improve the
way we do lazy interrupt handling (and make it work properly with
"edge" triggered interrupt sources), and while at it found & fixed
a wagon of issues in those areas, including adding support for page
fault retry & fatal signals on page faults.
- Your usual random batch of small fixes & updates, including a bunch
of new embedded boards, both Freescale and APM based ones, etc..."
I fixed up some conflicts with the generalized irq-domain changes from
Grant Likely, hopefully correctly.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (141 commits)
powerpc/ps3: Do not adjust the wrapper load address
powerpc: Remove the rest of the legacy iSeries include files
powerpc: Remove the remaining CONFIG_PPC_ISERIES pieces
init: Remove CONFIG_PPC_ISERIES
powerpc: Remove FW_FEATURE ISERIES from arch code
tty/hvc_vio: FW_FEATURE_ISERIES is no longer selectable
powerpc/spufs: Fix double unlocks
powerpc/5200: convert mpc5200 to use of_platform_populate()
powerpc/mpc5200: add options to mpc5200_defconfig
powerpc/mpc52xx: add a4m072 board support
powerpc/mpc5200: update mpc5200_defconfig to fit for charon board
Documentation/powerpc/mpc52xx.txt: Checkpatch cleanup
powerpc/44x: Add additional device support for APM821xx SoC and Bluestone board
powerpc/44x: Add support PCI-E for APM821xx SoC and Bluestone board
MAINTAINERS: Update PowerPC 4xx tree
powerpc/44x: The bug fixed support for APM821xx SoC and Bluestone board
powerpc: document the FSL MPIC message register binding
powerpc: add support for MPIC message register API
powerpc/fsl: Added aliased MSIIR register address to MSI node in dts
powerpc/85xx: mpc8548cds - add 36-bit dts
...
This branch contains a minor documentation addition, a utility
function for parsing string properties needed by some of the new ARM
platforms, disables dynamic DT code that isn't used anywhere but on a
few PPC machines, and exports DT node compatible data to userspace via
UEVENT properties. Nothing earth shattering here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=kK/B
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull core device tree changes for Linux v3.4 from Grant Likely:
"This branch contains a minor documentation addition, a utility
function for parsing string properties needed by some of the new ARM
platforms, disables dynamic DT code that isn't used anywhere but on a
few PPC machines, and exports DT node compatible data to userspace via
UEVENT properties. Nothing earth shattering here."
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux-2.6:
of: Only compile OF_DYNAMIC on PowerPC pseries and iseries
arm/dts: OMAP3: Add omap3evm and am335xevm support
drivercore: Output common devicetree information in uevent
of: Add of_property_match_string() to find index into a string list
Assorted extensions and fixes including:
* Introduction of early/late suspend/hibernation device callbacks.
* Generic PM domains extensions and fixes.
* devfreq updates from Axel Lin and MyungJoo Ham.
* Device PM QoS updates.
* Fixes of concurrency problems with wakeup sources.
* System suspend and hibernation fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=IGhc
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates for 3.4 from Rafael Wysocki:
"Assorted extensions and fixes including:
* Introduction of early/late suspend/hibernation device callbacks.
* Generic PM domains extensions and fixes.
* devfreq updates from Axel Lin and MyungJoo Ham.
* Device PM QoS updates.
* Fixes of concurrency problems with wakeup sources.
* System suspend and hibernation fixes."
* tag 'pm-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (43 commits)
PM / Domains: Check domain status during hibernation restore of devices
PM / devfreq: add relation of recommended frequency.
PM / shmobile: Make MTU2 driver use pm_genpd_dev_always_on()
PM / shmobile: Make CMT driver use pm_genpd_dev_always_on()
PM / shmobile: Make TMU driver use pm_genpd_dev_always_on()
PM / Domains: Introduce "always on" device flag
PM / Domains: Fix hibernation restore of devices, v2
PM / Domains: Fix handling of wakeup devices during system resume
sh_mmcif / PM: Use PM QoS latency constraint
tmio_mmc / PM: Use PM QoS latency constraint
PM / QoS: Make it possible to expose PM QoS latency constraints
PM / Sleep: JBD and JBD2 missing set_freezable()
PM / Domains: Fix include for PM_GENERIC_DOMAINS=n case
PM / Freezer: Remove references to TIF_FREEZE in comments
PM / Sleep: Add more wakeup source initialization routines
PM / Hibernate: Enable usermodehelpers in hibernate() error path
PM / Sleep: Make __pm_stay_awake() delete wakeup source timers
PM / Sleep: Fix race conditions related to wakeup source timer function
PM / Sleep: Fix possible infinite loop during wakeup source destruction
PM / Hibernate: print physical addresses consistently with other parts of kernel
...
Some fields can be set without mutex protection. Initialize them before
locking the mutex.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Remove an error label in dma_buf_attach() that just returns an error
code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
ops, ops->map_dma_buf and ops->unmap_dma_buf are guaranteed to be
non-NULL by a check in dma_buf_export(). Remove NULL checks on those
variables in the other API functions.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
This allows drivers to make the dma buf operations structure constant.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Power domains that were off before hibernation shouldn't be turned on
during device restore, so prevent that from happening.
This change fixes up commit 65533bbf63
PM / Domains: Fix hibernation restore of devices, v2
that didn't include it by mistake.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* pm-domains:
PM / shmobile: Make MTU2 driver use pm_genpd_dev_always_on()
PM / shmobile: Make CMT driver use pm_genpd_dev_always_on()
PM / shmobile: Make TMU driver use pm_genpd_dev_always_on()
PM / Domains: Introduce "always on" device flag
PM / Domains: Fix hibernation restore of devices, v2
PM / Domains: Fix handling of wakeup devices during system resume
* pm-qos:
sh_mmcif / PM: Use PM QoS latency constraint
tmio_mmc / PM: Use PM QoS latency constraint
PM / QoS: Make it possible to expose PM QoS latency constraints
The TMU device on the Mackerel board belongs to the A4R power domain
and loses power when the domain is turned off. Unfortunately, the
TMU driver is not prepared to cope with such situations and crashes
the system when that happens. To work around this problem introduce
a new helper function, pm_genpd_dev_always_on(), allowing a device
driver to mark its device as "always on" in case it belongs to a PM
domain, which will make the generic PM domains core code avoid
powering off the domain containing the device, both at run time and
during system suspend.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Simon Horman <horms@verge.net.au>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: stable@vger.kernel.org
During resume from hibernation pm_genpd_restore_noirq() should only
power off domains whose suspend_power_off flags are set once and
not every time it is called for a device in the given domain.
Moreover, it shouldn't decrement genpd->suspended_count, because
that field is not touched during device freezing and therefore it is
always equal to 0 when pm_genpd_restore_noirq() runs for the first
device in the given domain.
This means pm_genpd_restore_noirq() may use genpd->suspended_count
to determine whether or not it it has been called for the domain in
question already in this cycle (it only needs to increment that
field every time it runs for this purpose) and whether or not it
should check if the domain needs to be powered off. For that to
work, though, pm_genpd_prepare() has to clear genpd->suspended_count
when it runs for the first device in the given domain (in which case
that flag need not be cleared during domain initialization).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: stable@vger.kernel.org
During system suspend pm_genpd_suspend_noirq() checks if the given
device is in a wakeup path (i.e. it appears to be needed for one or
more wakeup devices to work or is a wakeup device itself) and if it
needs to be "active" for wakeup to work. If that is the case, the
function returns 0 without incrementing the device domain's counter
of suspended devices and without executing genpd_stop_dev() for the
device. In consequence, the device is not stopped (e.g. its clock
isn't disabled) and power is always supplied to its domain in the
resulting system sleep state.
However, pm_genpd_resume_noirq() doesn't repeat that check and it
runs genpd_start_dev() and decrements the domain's counter of
suspended devices even for the wakeup device that weren't stopped by
pm_genpd_suspend_noirq(). As a result, the start callback may be run
unnecessarily for them and their domains' counters of suspended
devices may become negative. Both outcomes aren't desirable, so fix
pm_genpd_resume_noirq() to look for wakeup devices that might not be
stopped by during system suspend.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Simon Horman <horms@verge.net.au>
Cc: stable@vger.kernel.org
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPW8yUAAoJEHm+PkMAQRiGhFIH/RGUPxGmUkJv8EP5I4HDA4dJ
c6/PrzZCHs8rxzYzvn7ojXqZGXTOAA5ZgS9A6LkJ2sxMFvgMnkpFi6B4CwMzizS3
vLWo/HNxbiTCNGFfQrhQB8O58uNI8wOBa87lrQfkXkDqN0cFhdjtIxeY1BD9LXIo
qbWysGxCcZhJWHapsQ3NZaVJQnIK5vA/+mhyYP4HzbcHI3aWnbIEZ8GQKeY28Ch0
+pct5UQBjZavV5SujaW0Xd65oIiycm8XHAQw6FxQy//DfaabauWgFteR162Q/oew
xxUBDOHF3nO1bdteHHaYqxig0j1MbIHsqxTnE/neR8UryF04//1SFF7DYuY/1pg=
=SV5V
-----END PGP SIGNATURE-----
Merge tag 'v3.3-rc7' into x86/mce
Merge reason: Update from an ancient -rc1 base to an almost-final stable kernel.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
A runtime suspend of a device (e.g. an MMC controller) belonging to
a power domain or, in a more complicated scenario, a runtime suspend
of another device in the same power domain, may cause power to be
removed from the entire domain. In that case, the amount of time
necessary to runtime-resume the given device (e.g. the MMC
controller) is often substantially greater than the time needed to
run its driver's runtime resume callback. That may hurt performance
in some situations, because user data may need to wait for the
device to become operational, so we should make it possible to
prevent that from happening.
For this reason, introduce a new sysfs attribute for devices,
power/pm_qos_resume_latency_us, allowing user space to specify the
upper bound of the time necessary to bring the (runtime-suspended)
device up after the resume of it has been requested. However, make
that attribute appear only for the devices whose drivers declare
support for it by calling the (new) dev_pm_qos_expose_latency_limit()
helper function with the appropriate initial value of the attribute.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
For files that are actively using linux/device.h, make sure
that they call it out. This will allow us to clean up some
of the implicit uses of linux/device.h within include/*
without introducing build regressions.
Yes, this was created by "cheating" -- i.e. the headers were
cleaned up, and then the fallout was found and fixed, and then
the two commits were reordered. This ensures we don't introduce
build regressions into the git history.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
[Fix for breakage which will be introduced during the merge window via
header reworks in another tree, the regmap tree does include device.h
but Paul's tree breaks that. Reworded subject to reflect -- broonie]
regmap.s uses devres_alloc() and others that are prototyped in device.h.
Include that to solve the following:
drivers/base/regmap/regmap.c: In function 'devm_regmap_init':
drivers/base/regmap/regmap.c:331:2: error: implicit declaration of function 'devres_alloc' [-Werror=implicit-function-declaration]
drivers/base/regmap/regmap.c:338:3: error: implicit declaration of function 'devres_add' [-Werror=implicit-function-declaration]
drivers/base/regmap/regmap.c:340:3: error: implicit declaration of function 'devres_free' [-Werror=implicit-function-declaration]
drivers/base/regmap/regmap.c: In function '_regmap_raw_write':
drivers/base/regmap/regmap.c:421:5: error: implicit declaration of function 'dev_err' [-Werror=implicit-function-declaration]
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The PowerPC legacy iSeries plateform is being removed along with the
"one looney iseries driver", so this code can now be removed as well.
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Came in in the deferred probe patch, quick, clean them up before a
kernel janitor finds them and sends me 4 individual patches to fix them
up...
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nothing outside of the driver core needs to get to the deferred probe
pointer, so move it inside the private area of 'struct device' so no one
tries to mess around with it.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow drivers to report at probe time that they cannot get all the resources
required by the device, and should be retried at a later time.
This should completely solve the problem of getting devices
initialized in the right order. Right now this is mostly handled by
mucking about with initcall ordering which is a complete hack, and
doesn't even remotely handle the case where device drivers are in
modules. This approach completely sidesteps the issues by allowing
driver registration to occur in any order, and any driver can request
to be retried after a few more other drivers get probed.
v4: - Integrate Manjunath's addition of a separate workqueue
- Change -EAGAIN to -EPROBE_DEFER for drivers to trigger deferral
- Update comment blocks to reflect how the code really works
v3: - Hold off workqueue scheduling until late_initcall so that the bulk
of driver probes are complete before we start retrying deferred devices.
- Tested with simple use cases. Still needs more testing though.
Using it to get rid of the gpio early_initcall madness, or to replace
the ASoC internal probe deferral code would be ideal.
v2: - added locking so it should no longer be utterly broken in that regard
- remove device from deferred list at device_del time.
- Still completely untested with any real use case, but has been
boot tested.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Dilan Lee <dilee@nvidia.com>
Cc: Manjunath GKondaiah <manjunath.gkondaiah@linaro.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: David Daney <david.daney@cavium.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most of the current users have register 0 as a volatile register or don't
have a register 0 so it's not been apparent that it's not getting synced.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* pm-domains:
PM / Domains: Fix include for PM_GENERIC_DOMAINS=n case
PM / Domains: Provide a dummy dev_gpd_data() when generic domains are not used
PM / Domains: Run late/early device suspend callbacks at the right time
ARM: EXYNOS: Hook up power domains to generic power domain infrastructure
PM / Domains: Add OF support
The existing wakeup source initialization routines are not
particularly useful for wakeup sources that aren't created by
wakeup_source_create(), because their users have to open code
filling the objects with zeros and setting their names. For this
reason, introduce routines that can be used for initializing, for
example, static wakeup source objects.
Requested-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
If __pm_stay_awake() is called after __pm_wakeup_event() for the same
wakep source object before its timer expires, it won't cancel the
timer, so the wakeup source will be deactivated from the timer
function as scheduled by __pm_wakeup_event(). In that case
__pm_stay_awake() doesn't have any effect beyond incrementing
the wakeup source's event_count field, although it should cancel
the timer and make the wakeup source stay active until __pm_relax()
is called for it.
To fix this problem make __pm_stay_awake() delete the wakeup source's
timer and ensure that it won't be deactivated from the timer funtion
afterwards by clearing its timer_expires field.
Reported-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
If __pm_wakeup_event() has been used (with a nonzero timeout) to
report a wakeup event and then __pm_relax() immediately followed by
__pm_stay_awake() is called or __pm_wakeup_event() is called once
again for the same wakeup source object before its timer expires, the
timer function pm_wakeup_timer_fn() may still be run as a result of
the previous __pm_wakeup_event() call. In either of those cases it
may mistakenly deactivate the wakeup source that has just been
activated.
To prevent that from happening, make wakeup_source_deactivate()
clear the wakeup source's timer_expires field and make
pm_wakeup_timer_fn() check if timer_expires is different from zero
and if it's not in future before calling wakeup_source_deactivate()
(if timer_expires is 0, it means that the timer has just been
deleted and if timer_expires is in future, it means that the timer
has just been rescheduled to a different time).
Reported-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
If wakeup_source_destroy() is called for an active wakeup source that
is never deactivated, it will spin forever. To prevent that from
happening, make wakeup_source_destroy() call __pm_relax() for the
wakeup source object it is about to free instead of waiting until
it will be deactivated by someone else. However, for this to work
it also needs to make sure that the timer function will not be
executed after the final __pm_relax(), so make it run
del_timer_sync() on the wakeup source's timer beforehand.
Additionally, update the kerneldoc comment to document the
requirement that __pm_stay_awake() and __pm_wakeup_event() must not
be run in parallel with wakeup_source_destroy().
Reported-by: Arve Hjønnevåg <arve@android.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Remove unused module.h and/or replace with export.h
as required.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Provide a regcache_sync_region() operation which allows drivers to
write only part of the cache back to the hardware. This is intended
for use in cases like power domains or DSP memories where part of the
device register map may be reset without fully resetting the device.
Fully supporting these devices is likely to require additional work to
make specific regions of the register map cache only while they are in
reset, but this is enough for most devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order to allow us to support partial sync operations add minimum and
maximum register arguments to the sync operation and update the rbtree
and lzo caches to use this new information. The LZO implementation is
obviously not good, we could exit the iteration earlier, but there may
be room for more wide reaching optimisation there.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Previously the cache would never be marked clean, meaning syncs would
never be suppressed which isn't the end of the world but could be
inefficient.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's not used as all cache types have sync operations so it's just dead
code which never gets tested.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a file called 'name' containing the name of the driver.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To enable writing to the regmap debugfs registers file users will
need to modify the source directly and #define REGMAP_ALLOW_WRITE_DEBUGFS.
The reason for this is that it is dangerous to expose this
functionality in general where clients could potentially be PMICs.
[A couple of minor style updates -- broonie]
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
regmap, allowing them to build further subsystem specific generic
features on top of the regmap.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPQriPAAoJEBus8iNuMP3d7H8P/0i0E0oGphczp6PiyNludQts
8xLeSSeNIM2tD78+jg16nBswNxp31mF0n1ueLEK3vblxAJaSm4x3FwD7+ssYcQnn
ItFeFhumBP2qISlSLjMLK+D7g7cxJQRoTuq6fjRxwjLQGhC3eHXz+aeNz+U92gLD
QM3hPKckGHkAJAg7jZmRk0BkH9TODoX+6QCXUxY+bEgxWSTC2nrEoFjoVv1dqGgj
1xPBVTEq3w1QLDy+JUuLVXCvv8ieoQ37j+9Qyciln+ive8oC1rm14wl7pSB/qIV+
MeBSjxc/Hv6l+jCEWa5fxf1RqRh3P5utcPQmuMWXHJhJ3HFheCv2d4/ZL3NiVi0I
NNGUATgfIxnSYfeN8ft9v2v7p7tWTQI+UFTfeQal1LhFY74p6JGuGcGtM536pRjG
qyhc2hDKc95TYCOTnaPGqWsczxZ1Lt4XkSAUuW7Nop43qynrlngSfHw8qn/QbyUW
S6xrzk72WQD3i0HwhWgaP0PsH4GGlEgbOqMUhppHbbvSC2VZ3K9HsHLJZLKjX3qC
8YP34oOohwDK3EOCGfdV1w7SPn3NU0DglTPi5Og+h39cN4xh+vAHAZkUKdA35IEM
9EANjeIWmGyZoFVgrj+NWtuz2wvboZrOEhuRSJBcbQF8LUpWYkEkGuhHM6lRSH66
7K37XUEQwjbXTR/rcpaI
=KhUJ
-----END PGP SIGNATURE-----
Merge tag 'topic/introspection' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into HEAD
New interfaces to allow other subsystems to gather information about the
regmap, allowing them to build further subsystem specific generic
features on top of the regmap.
Merged into ASoC in order to allow us to implement SND_SOC_BYTES_MASK()
controls which need to know the word size of the underlying registers.
Fall back to a register by register read to do so; most likely we'll be
cache only so the overhead will be low.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Generic infrastructure based on top of regmap may want to operate on
blocks of data and therefore find it useful to find the size of the
register values. Provide an accessor operation for this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPQDoTAAoJEHm+PkMAQRiGMpYH/ibfyIFBrKMD1v/s9oNvp8rS
c7J7E7mHZOylCHrpIS3lX3ZbOfOe33Ln0Z59f1/TcV4CMMz0NrKYcTC8erj/H/DA
8DRYegiczWKqiXRgktwaZXkJcwXYdOOL1WQYxuzzbZcwRrNBY2QpH7Zu8Bj+TPAy
d4fvJHWdlh4sbWVdQmLRbp04UB9J/Z5/uWmSNvVQjLLdRlD+mEBbt7JjiNY6sUVC
2sJoAs9F3UlHu7VaN+JIhMOGZ3GqOpHGBxN/aWxJ/7GsXdXuAfCrxoPxaAe4xzOa
HndN5ZDyg02Vy5uDeUzj+HJPW3M8L4Q0nwxAYb3ZnQ5tbpu1Q2cHfIBealomWCQ=
=R91X
-----END PGP SIGNATURE-----
Merge tag 'v3.3-rc4' into for-3.4 in order to resolve the conflict
resolved below within the FSI driver and allow the application of the
dmaeengine conversion that depends on this resolution.
Linux 3.3-rc4
Conflicts:
sound/soc/sh/fsi.c
method for register cache initialisation is used. Only affects a fairly
small proportion of users that both don't use explicit register defaults
and do use the cache.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pU4C
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Fixes a bootstrapping issue for some registers when a less commonly used
method for register cache initialisation is used. Only affects a fairly
small proportion of users that both don't use explicit register defaults
and do use the cache.
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Fix cache defaults initialization from raw cache defaults
During regcache_init, if client has not passed the
default data of cached register then it is directly
read from the hw to initialize cache. This hw register
read happens before cache ops are initialized and hence
avoiding register read to check for the data available
on cache or not by enabling flag of cache_bypass.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently registers with a value of 0 are ignored when initializing the register
defaults from raw defaults. This worked in the past, because registers without a
explicit default were assumed to have a default value of 0. This was changed in
commit b03622a8 ("regmap: Ensure rbtree syncs registers set to zero properly").
As a result registers, which have a raw default value of 0 are now assumed to
have no default. This again can result in unnecessary writes when syncing the
cache. It will also result in unnecessary reads for e.g. the first update
operation. In the case where readback is not possible this will even let the
update operation fail, if the register has not been written to before.
So this patch removes the check. Instead it adds a check to ignore raw defaults
for registers which are volatile, since those registers are not cached.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
The bulk_write() supports the data transfer to multi
register which takes the data into cpu_endianness format
and does formatting of data to device format before
sending to device.
The transfer can be completed in single transfer or multiple
transfer based on data formatting.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Initialize wakeup source locks in wakeup_source_add() instead of
wakeup_source_create(), because otherwise the locks of the wakeup
sources that haven't been allocated with wakeup_source_create()
aren't initialized and handled properly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Adding support for caching of data into the
non-volatile register from the call of reg_raw_write().
This will allow the larger block of data write into multiple
register without worrying whether register is cached or not
through reg_raw_write().
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Traditionally, any System-on-Chip based platform creates a flat list
of platform_devices directly under /sys/devices/platform.
In order to give these some better structure, this introduces a new
bus type for soc_devices that are registered with the new
soc_device_register() function. All devices that are on the same
chip should then be registered as child devices of the soc device.
The soc bus also exports a few standardised device attributes which
allow user space to query the specific type of soc.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The first parameter should be "number of elements" and the second parameter
should be "element size".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Due to the sysdev conversion to struct device, the cpu objects get
reused when adding a cpu after offlining it, which causes a big warning
that the kobject portion is not properly initialized.
So clear out the object before we register it again, so all is quiet.
Reported-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was a cut'n'paste from some older code.
Since we're about to add debugfs support don't do the obvious thing and
use bool, use u32 instead (which debugfs has been using since time
immemorial).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This was done to resolve a merge and build problem with the
drivers/acpi/processor_driver.c file.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the movement of the cpu sysdev code to be real stuct devices, now
when we remove a cpu from the system, the driver core rightfully
complains that there is not a release method for this device.
For now, paper over this issue by quieting the driver core, but comment
this in detail. This will be resolved in future kernels to be solved
properly.
Reported-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When userspace needs to find a specific device, it currently isn't easy to
resolve a /sys/devices/ path from a specific device tree node. Nor is it
easy to obtain the compatible list for devices.
This patch generalizes the code that inserts OF_* values into the uevent
device attribute so that any device that is attached to an OF node will
have that information exported to userspace. Without this patch only
platform devices and some powerpc-specific busses have access to this
data.
The original function also creates a MODALIAS property for the compatible
list, but that code has not been generalized into the common case because
it has the potential to break module loading on a lot of bus types. Bus
types are still responsible for their own MODALIAS properties.
Boot tested on ARM and compile tested on PowerPC and SPARC.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Frederic Lambert <frdrc66@gmail.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Mark Brown <broonie@sirena.org.uk>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'v3.4-for-rafael' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Hook up power domains to generic power domain infrastructure
PM / Domains: Add OF support
.. several days delayed. No reason, I just didn't think of it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPKF4KAAoJEHm+PkMAQRiGw/YH+wXg2DpZUuHeBK52zMGlJBPc
DzX11/Uan3Y07gM0JbDzuVxwjX4vdxR2bV6r1qsLP8JEUnE8jyFC32DBGi5WAht7
F4KU/Uov2Ds5/wzvY4Iuo01C+JftQHXuy/Sbhck1d0LI0yjLejRaw+zuJv0x2/eS
7YqV+KTGE1lDuJs/Gyq1Vqr1g9831AuS1tv/g3gaqBuN6TcPBFCocaVxzwrUc+y6
94h26XbbOhQRIz38oqUkiqAGnvYS61ocyBcEiRHf0dXkNSDIINqlgukvd7YTXouA
jj/w/DWpMRcQuYAgqkrurr9+yWC9hVQcsvvQ5sAQnIPcxoR868sg1pO8Oheq+1g=
=kUzV
-----END PGP SIGNATURE-----
Merge tag 'v3.3-rc2' into for-3.4
A reasonable amount of new development is causing fiddly merge conflicts
between different resource management changes (mostly fixing bugs in
resource management due to noticing things while doing enhancements in
the same area).
Linux 3.3-rc2
.. several days delayed. No reason, I just didn't think of it.
regcache_set_val() returns false if cache[idx] != val.
Thus it actually is not unreachable.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Save error handling and unwinding code in drivers by providing managed
versions of the regmap init functions, simplifying usage.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Using .format_write means, we have a custom function to write to the
chip, but not to read back. Also, mark registers as "not precious" and
"not volatile" which is implicit because we cannot read them. Make those
functions use 'regmap_readable' to reuse the checks done there.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For the upcoming 2/6-format, we don't see debugfs output otherwise,
since the current division results in 0. I'd think 10/14 is broken
currently, too.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
After the introduction of the late/early phases of device
suspend/resume during system-wide power transitions it is possible
to make the generic PM domains code execute its default late/early
device suspend/resume callbacks during those phases instead of the
corresponding _noirq phases. The _noirq device suspend/resume
phases were only used for executing those callbacks, because this
was the only way it could be done, but now we can do better.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Introduce generic subsystem callbacks for the new phases of device
suspend/resume during system power transitions: "late suspend",
"early resume", "late freeze", "early thaw", "late poweroff",
"early restore".
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The current device suspend/resume phases during system-wide power
transitions appear to be insufficient for some platforms that want
to use the same callback routines for saving device states and
related operations during runtime suspend/resume as well as during
system suspend/resume. In principle, they could point their
.suspend_noirq() and .resume_noirq() to the same callback routines
as their .runtime_suspend() and .runtime_resume(), respectively,
but at least some of them require device interrupts to be enabled
while the code in those routines is running.
It also makes sense to have device suspend-resume callbacks that will
be executed with runtime PM disabled and with device interrupts
enabled in case someone needs to run some special code in that
context during system-wide power transitions.
Apart from this, .suspend_noirq() and .resume_noirq() were introduced
as a workaround for drivers using shared interrupts and failing to
prevent their interrupt handlers from accessing suspended hardware.
It appears to be better not to use them for other porposes, or we may
have to deal with some serious confusion (which seems to be happening
already).
For the above reasons, introduce new device suspend/resume phases,
"late suspend" and "early resume" (and analogously for hibernation)
whose callback will be executed with runtime PM disabled and with
device interrupts enabled and whose callback pointers generally may
point to runtime suspend/resume routines.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
It contains the removal of the sysdev code, now that all users of it are
gone, as well as some sysfs bugfixes that have been reported by users.
There are also some documentation updates here as well.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk8jKW4ACgkQMUfUDdst+ynAUwCfVWwHJxpb4DSSMVZhGOnHMQrL
ZjIAn00gPeSs5u8y1nPvFrFikbon4FDs
=bzVy
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.3-rc1-bugfixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Here are some patches for the 3.3-rc1 tree.
It contains the removal of the sysdev code, now that all users of it are
gone, as well as some sysfs bugfixes that have been reported by users.
There are also some documentation updates here as well.
* tag 'driver-core-3.3-rc1-bugfixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
sysfs: Complain bitterly about attempts to remove files from nonexistent directories.
stable: update documentation to ask for kernel version
base/core.c:fix typo in comment in function device_add
Documentation: devres: add allocation functions to list of supported calls
Documentation update for the driver model core
kernel-doc: fix new warnings in driver-core
kernel-doc: fix new warnings in debugfs
kernel-doc: fix new warnings in device.h
driver core: remove drivers/base/sys.c and include/linux/sysdev.h
A device node pointer is added to generic pm domain structure to associate
the domain with a node in the device tree. The platform code parses the
device tree to find available nodes representing the generic power domain,
instantiates the available domains and initializes them by calling
pm_genpd_init().
Nodes representing the devices include a phandle of the power domain to
which it belongs. As these devices get instantiated, the driver code
checkes for availability of a power domain phandle, converts the phandle
to a device node and uses the new pm_genpd_of_add_device() api to
associate the device with a power domain.
pm_genpd_of_add_device() runs through its list of registered power domains
and matches the OF node of the domain with the one specified as the
parameter. If a match is found, the device is associated with the matched
domain.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch is based on Andi Kleen's work:
Implement autoprobing/loading of modules serving CPU
specific features (x86cpu autoloading).
And Kay Siever's work to get rid of sysdev cpu structures
and making use of struct device instead.
Before, the cpuid driver had to be loaded to get the x86cpu
autoloading feature. With this patch autoloading works through
the /sys/devices/system/cpu object
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Dave Jones <davej@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Most of the data exposed via debugfs is for or from the cache so reset
all the debugfs configuration to make sure everything is up to date with
the latest configuration, especially if we're changing cache type.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
reset support as a result of some subsequent work. There's only one
mainline user for the code path that's updated right now (wm8994) so
should be low risk.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=N3hl
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
A fairly simple bugfix for a WARN_ON() which was triggered in the cache
reset support as a result of some subsequent work. There's only one
mainline user for the code path that's updated right now (wm8994) so
should be low risk.
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Reset cache status when reinitialsing the cache
Stephen Warren