A cold reset can be triggered because of DMA stop issues, and this leads
to TSF being cleared on all chipsets. To properly deal with this, always
save the TSF.
Additionally, account for the time it takes to do the actual chip reset,
which can be quite significant. On AR9344 it takes around 4.5 ms.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of checking the queues in a loop with hardcoded sleep times
inbetween, use a wait queue to trigger queue checks after the tx
processing tasklet has run.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the software has processed all packets, checking the hardware queue
is unnecessary.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When operating in client mode, the short period of time between scanning
and associating is often enough to put the hardware through several
FULL-SLEEP <-> AWAKE transitions, each wakeup requiring a reset to fully
recover the hardware.
This is completely unnecessary and can easily be avoided by deferring
the switch to full sleep.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since calibration data reuse is not enabled in
SoC chips, simplify the IQ calibration code.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CL calibration is applicable for all chips and the
enable/disable knob comes via the INI file. For PCOEM
chips, the calibration data is reused when Fast Channel Change
is used. Caldata reuse is not enabled for SoC chips, so remove
the CL post processing code.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TX IQ calibration is always enabled for SoC chips.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RTT is enabled only for AR9462 and MCI for AR9462/AR9565.
Also, manual peak calibration is not done for any of the
SoC chips.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Though there is some overlap between the calibration mechanisms
of PC-OEM cards and SoC chip families, dumping both of them
into a single function makes things hard to understand.
ar9003_hw_init_cal() is unreadable with chip-specific segments
scattered around. To make the logic understandable, use
different functions for client cards and SoC chips. Some
code is duplicated, but in the long run, it makes the code
more maintanable.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SC_OP_INVALID is zero so the test is always false. We're supposed to be
testing the lowest bit instead.
Fixes: 89f927af7f ('ath9k: add TX99 support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CUS227, which is an AR9340 based card used in Qualcomm's
Allplay platforms requires a custom TX gain array, based
on the index 7. Add suport for this.
Cc: Michael Larson <mlarson@qce.qualcomm.com>
Cc: Stephen Collmeyer <scollmey@qce.qualcomm.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This HW config option is always set to true and is not needed.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the WoW code to wow.c and compile it conditionally
based on CONFIG_ATH9K_WOW.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW routines to set various WoW registers are present
in wow.c. For some reason, it has been compiled as part
of the main ath9k.ko module all this time, when it should
really be part of ath9k_hw.ko. This patch renames the file to
ar9003_wow.ko and adds it to ath9k_hw.ko.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use CONFIG_ATH9K_TX99 to properly enclose the tx99 code
and make sure that it is not compiled as part of the driver
when it is not selected. Move the tx99 code to a new file tx99.c
and also add ATH9K_DEBUGFS as a dependency in Kconfig.
This reduces the module size on platforms like OpenWrt where
ATH9K_DEBUGFS is selected, but TX99 might be disabled.
Cc: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull networking fixes from David Miller:
"Mostly these are fixes for fallout due to merge window changes, as
well as cures for problems that have been with us for a much longer
period of time"
1) Johannes Berg noticed two major deficiencies in our genetlink
registration. Some genetlink protocols we passing in constant
counts for their ops array rather than something like
ARRAY_SIZE(ops) or similar. Also, some genetlink protocols were
using fixed IDs for their multicast groups.
We have to retain these fixed IDs to keep existing userland tools
working, but reserve them so that other multicast groups used by
other protocols can not possibly conflict.
In dealing with these two problems, we actually now use less state
management for genetlink operations and multicast groups.
2) When configuring interface hardware timestamping, fix several
drivers that simply do not validate that the hwtstamp_config value
is one the driver actually supports. From Ben Hutchings.
3) Invalid memory references in mwifiex driver, from Amitkumar Karwar.
4) In dev_forward_skb(), set the skb->protocol in the right order
relative to skb_scrub_packet(). From Alexei Starovoitov.
5) Bridge erroneously fails to use the proper wrapper functions to make
calls to netdev_ops->ndo_vlan_rx_{add,kill}_vid. Fix from Toshiaki
Makita.
6) When detaching a bridge port, make sure to flush all VLAN IDs to
prevent them from leaking, also from Toshiaki Makita.
7) Put in a compromise for TCP Small Queues so that deep queued devices
that delay TX reclaim non-trivially don't have such a performance
decrease. One particularly problematic area is 802.11 AMPDU in
wireless. From Eric Dumazet.
8) Fix crashes in tcp_fastopen_cache_get(), we can see NULL socket dsts
here. Fix from Eric Dumzaet, reported by Dave Jones.
9) Fix use after free in ipv6 SIT driver, from Willem de Bruijn.
10) When computing mergeable buffer sizes, virtio-net fails to take the
virtio-net header into account. From Michael Dalton.
11) Fix seqlock deadlock in ip4_datagram_connect() wrt. statistic
bumping, this one has been with us for a while. From Eric Dumazet.
12) Fix NULL deref in the new TIPC fragmentation handling, from Erik
Hugne.
13) 6lowpan bit used for traffic classification was wrong, from Jukka
Rissanen.
14) macvlan has the same issue as normal vlans did wrt. propagating LRO
disabling down to the real device, fix it the same way. From Michal
Kubecek.
15) CPSW driver needs to soft reset all slaves during suspend, from
Daniel Mack.
16) Fix small frame pacing in FQ packet scheduler, from Eric Dumazet.
17) The xen-netfront RX buffer refill timer isn't properly scheduled on
partial RX allocation success, from Ma JieYue.
18) When ipv6 ping protocol support was added, the AF_INET6 protocol
initialization cleanup path on failure was borked a little. Fix
from Vlad Yasevich.
19) If a socket disconnects during a read/recvmsg/recvfrom/etc that
blocks we can do the wrong thing with the msg_name we write back to
userspace. From Hannes Frederic Sowa. There is another fix in the
works from Hannes which will prevent future problems of this nature.
20) Fix route leak in VTI tunnel transmit, from Fan Du.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (106 commits)
genetlink: make multicast groups const, prevent abuse
genetlink: pass family to functions using groups
genetlink: add and use genl_set_err()
genetlink: remove family pointer from genl_multicast_group
genetlink: remove genl_unregister_mc_group()
hsr: don't call genl_unregister_mc_group()
quota/genetlink: use proper genetlink multicast APIs
drop_monitor/genetlink: use proper genetlink multicast APIs
genetlink: only pass array to genl_register_family_with_ops()
tcp: don't update snd_nxt, when a socket is switched from repair mode
atm: idt77252: fix dev refcnt leak
xfrm: Release dst if this dst is improper for vti tunnel
netlink: fix documentation typo in netlink_set_err()
be2net: Delete secondary unicast MAC addresses during be_close
be2net: Fix unconditional enabling of Rx interface options
net, virtio_net: replace the magic value
ping: prevent NULL pointer dereference on write to msg_name
bnx2x: Prevent "timeout waiting for state X"
bnx2x: prevent CFC attention
bnx2x: Prevent panic during DMAE timeout
...
As suggested by David Miller, make genl_register_family_with_ops()
a macro and pass only the array, evaluating ARRAY_SIZE() in the
macro, this is a little safer.
The openvswitch has some indirection, assing ops/n_ops directly in
that code. This might ultimately just assign the pointers in the
family initializations, saving the struct genl_family_and_ops and
code (once mcast groups are handled differently.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free temporary 'chanspecs' avoiding leakage.
Signed-off-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
This driver uses a number of macros to get and set various fields in the
RX and TX descriptors. To work correctly, a u8 pointer to the descriptor
must be used; however, in some cases a descriptor structure pointer is used
instead. In addition, a duplicated statement is removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) After driver load failure, clear 'card->adapter' instead of
card pointer so that card specific cleanup is performed later
when user unloads the driver.
2) Clear usb_card pointer in disconnect handler to avoid invalid
memory access when user unloads the driver after removing the
card.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When driver is failed to load, card pointer doesn't get
freed. We will free it in cleanup handler which is called
in failure as well as unload path.
Also, update drvdata in init/cleanup handlers instead of
register/unregister handlers.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) Currently we freeing wdev for each interface in driver unload
path. We may leak memory if user have already deleted an interface.
mwifiex_add_virtual_intf() allocates wdev structure. So it should
be freed in mwifiex_del_virtual_intf().
This will make sure that wdev will be freed when user deletes an
interface and also in unload path.
2) "priv->netdev->ieee80211_ptr" should also be cleared in
mwifiex_del_virtual_intf.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't need to free/unregister wiphy when
mwifiex_register_cfg80211() fails. The routine internally takes
care of it. This redundant code can cause NULL pointer dereference,
for adapter->wiphy.
Reported-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) If register_netdevice() is failed, we are freeing netdev
pointer, but priv->netdev is not cleared. This gives kernel
paging request error when driver is unloaded or interface is
deleted. Fix the problem by clearing the pointer.
2) Fix memory leak issue by freeing 'wdev' in failure paths.
Also, clear priv->wdev pointer.
As mwifiex_add_virtual_intf() successfully handles the
failure conditions, redundant code under err_add_intf label
is removed in this patch.
Reported-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mwifiex_add_virtual_intf() returns ERR_PTR values. So use IS_ERR()
macro instead of checking for NULL pointer.
Reported-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "rt2x00: fix HT TX descriptor settings regression"
assumes that the control parameter to rt2x00mac_tx is always non-NULL.
There is an internal call in rt2x00lib_bc_buffer_iter where NULL is
passed. Fix the resulting crash by adding an initialized dummy on-stack
ieee80211_tx_control struct.
Cc: stable@vger.kernel.org # 3.7+
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some boards which are based on AR9300, AR9580 or
AR9550, MCS15 usage is problematic.
This is because these boards use a "frequency doubler",
which doubles the refclk to get better EVM, but causes
spurs. Handle this properly in the driver to recover
throughput.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A world regulatory domain check was in place that
prevents user dynamic regulatory hints from being
processed. This was there for historical reasons
as this was only possible previously for world
roaming cards and dynamic regulatory settings was
only possible for country IEs. Fix this by enforcing
the world regulatory domain check only for when the
initiator is a country IE. Support for dynamic user
regulatory support is already checked.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enhances the type safety for the kfifo API. It is now safe
to put const data into a non const FIFO and the API will now generate a
compiler warning when reading from the fifo where the destination
address is pointing to a const variable.
As a side effect the kfifo_put() does now expect the value of an element
instead a pointer to the element. This was suggested Russell King. It
make the handling of the kfifo_put easier since there is no need to
create a helper variable for getting the address of a pointer or to pass
integers of different sizes.
IMHO the API break is okay, since there are currently only six users of
kfifo_put().
The code is also cleaner by kicking out the "if (0)" expressions.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
John W. Linville says:
====================
pull request: wireless 2013-11-14
Please pull this batch of fixes intended for the 3.13 stream!
Amitkumar Karwar offers a quartet of mwifiex fixes, including an
endian fix and three fixes for invalid memory access.
Avinash Patil trims the packet length value for packets received from
an SDIO interface.
Colin Ian King fixes a NULL pointer dereference in the rtlwifi
efuse code.
Dan Carpenter cleans-up an mwifiex integer underflow, a potential
libertas oops, a memory corrupion bug in wcn36xx, and a locking issue
also in wcn36xx.
Dan Williams helps prism54 devices to avoid being misclassified as
Ethernet devices.
Felipe Pena fixes a couple of typo errors, one in rt2x00 and the
other in rtlwifi.
Janusz Dziedzic corrects a pair of DFS-related problems in ath9k.
Larry Finger patches three rtlwifi drivers to correctly report signal
strength even for an unassociated AP.
Mark Cave-Ayland rewrites some endian-illiterate packet type extraction
code in rtlwifi.
Stanislaw Gruszka addresses an rt2x00 regression related to setting
HT station WCID and AMPDU density parameters.
Sujith Manoharan corrects the initvals settings for AR9485.
Ujjal Roy patches an obscure bit of code in mwifiex that was using
the wrong definition of eth_hdr when briding patches in AP mode.
Wei Yongjun fixes a couple of bugs: one is a return code handling
bug in libertas; and, the other is a locking issue in wcn36xx.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that genl_ops are no longer modified in place when
registering, they can be made const. This patch was done
mostly with spatch:
@@
identifier ops;
@@
+const
struct genl_ops ops[] = {
...
};
(except the struct thing in net/openvswitch/datapath.c)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
Userspace uses the netdev devtype for stuff like device naming and type
detection. Be nice and set it. Remove the pointless #if/#endif around
SET_NETDEV_DEV too.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are several places which are missing unlocks.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the missing unlock before return from function
wcn36xx_smd_update_proberesp_tmpl() in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, the PLL is turned off for AR9485 when
switching to a low power state, but AR9485 has an issue
where the card will become unresponsive if left idle
for a long time without any traffic. To fix this,
force the PLL to always be on using a different initval
array, ar9485_1_1_pll_on_cdr_on_clkreq_disable_L1.
This is done for most of the AR9485 based cards
like HB125, WB225 etc. but certain models require the
feature to be turned off. Identify such cards and use
default values for them.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On 64 bit systems we write past the end of the arg[] array.
Fixes: 8e84c25821 ('wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The eth_hdr is never defined in this driver but it gets compiled
without any warning/error because kernel has defined eth_hdr.
Fix it by defining our own p_ethhdr and use it instead of eth_hdr.
Cc: <stable@vger.kernel.org> # 3.7+
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While receiving a packet on SDIO interface, we allocate skb with
size multiple of SDIO block size. We need to resize this skb
after RX using packet length from RX header.
Cc: <stable@vger.kernel.org>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The routine that processes received frames was returning the RSSI value for the
signal strength; however, that value is available only for associated APs. As
a result, the strength was the absurd value of 10 dBm. As a result, scans
return incorrect values for the strength, which causes unwanted attempts to roam.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.1+]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau