The pm_request_idle() in pm_generic_complete() is pointless as it is
called with the runtime PM usage counter different from zero (bumped
up by the core during the prepare phase of system suspend) and the
core calls pm_runtime_put() for all devices after executing their
complete callbacks, so drop it.
This allows the PCI PM layer to use pm_generic_complete() too.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
As we continue to push of_node towards the outskirts of irq domains,
let's start tackling the case of msi_create_irq_domain and its little
friends.
This has limited impact in both PCI/MSI, platform MSI, and a few
drivers.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Graeme Gregory <graeme@xora.org.uk>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Link: http://lkml.kernel.org/r/1444737105-31573-17-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit bac2a909a0 (PCI / PM: Avoid resuming PCI devices during
system suspend) introduced a mechanism by which some PCI devices that
were runtime-suspended at the system suspend time might be left in
that state for the duration of the system suspend-resume cycle.
However, it overlooked devices that were marked as capable of waking
up the system just because PME support was detected in their PCI
config space.
Namely, in that case, device_can_wakeup(dev) returns 'true' for the
device and if the device is not configured for system wakeup,
device_may_wakeup(dev) returns 'false' and it will be resumed during
system suspend even though configuring it for system wakeup may not
really make sense at all.
To avoid this problem, simply disable PME for PCI devices that have
not been configured for system wakeup and are runtime-suspended at
the system suspend time for the duration of the suspend-resume cycle.
If the device is in D3cold, its config space is not available and it
shouldn't be written to, but that's only possible if the device
has platform PM support and the platform code is responsible for
checking whether or not the device's configuration is suitable for
system suspend in that case.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make the offset from the beginning of the "reg" property be from the
starting bus number, rather than zero. Hoist the invariant size
calculation out of the mapping for loop.
Update host-generic-pci.txt to clarify the semantics of the "reg" property
with respect to non-zero starting bus numbers.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Now that we advertise a PCIe capability, the Linux PCI layer will not scan
the bus for devices other than in slot 0. This makes the work-around to
trap accesses to devices other than slot 0 unnecessary.
Tested-by: Willy Tarreau <w@1wt.eu> (Iomega iConnect Kirkwood, MiraBox Armada 370)
Tested-by: Andrew Lunn <andrew@lunn.ch> (D-Link DIR664 Kirkwood)
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add a PCI Express root complex capability block so the PCI layer identifies
the bridge as a PCI Express device.
We expose this as a version 1 PCIe capability block, with slot support. We
disable the clock power management capability as this depends on boards
wiring the CLKREQ# signal.
Tested-by: Willy Tarreau <w@1wt.eu> (Iomega iConnect Kirkwood, MiraBox Armada 370)
Tested-by: Andrew Lunn <andrew@lunn.ch> (D-Link DIR664 Kirkwood)
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add an implementation to handle clock and reset handling that is compliant
with the PCIe specification. The clock should be running and stable for
100us prior to reset being released, and we should re-assert reset prior to
stopping the clock.
Tested-by: Willy Tarreau <w@1wt.eu> (Iomega iConnect Kirkwood, MiraBox Armada 370)
Tested-by: Andrew Lunn <andrew@lunn.ch> (D-Link DIR664 Kirkwood)
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Use a gpio_desc to carry around the gpio, so we can then make use of the
GPIOF_ACTIVE_LOW property rather than carrying that around as well. This
also avoids needing to use gpio_is_valid() to check whether we have a GPIO;
checking for a non-NULL descriptor is simpler.
Tested-by: Willy Tarreau <w@1wt.eu> (Iomega iConnect Kirkwood, MiraBox Armada 370)
Tested-by: Andrew Lunn <andrew@lunn.ch> (D-Link DIR664 Kirkwood)
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Rather than using devm_kzalloc() and multiplying the element and number,
use the provided devm_kcalloc() helper for this.
Tested-by: Willy Tarreau <w@1wt.eu> (Iomega iConnect Kirkwood, MiraBox Armada 370)
Tested-by: Andrew Lunn <andrew@lunn.ch> (D-Link DIR664 Kirkwood)
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
We are in a context where we can sleep, and the PCIe reset gpio may be on
an I2C expander. Use the cansleep() variant when setting the GPIO value.
Tested-by: Willy Tarreau <w@1wt.eu> (Iomega iConnect Kirkwood, MiraBox Armada 370)
Tested-by: Andrew Lunn <andrew@lunn.ch> (D-Link DIR664 Kirkwood)
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Split the PCIe port DT parsing and resource claiming from setting up the
actual ports. This allows us to gather all the resources first, before
touching the hardware. This is important as some of these resources (such
as the GPIO for the PCIe reset) may defer probing.
Tested-by: Willy Tarreau <w@1wt.eu> (Iomega iConnect Kirkwood, MiraBox Armada 370)
Tested-by: Andrew Lunn <andrew@lunn.ch> (D-Link DIR664 Kirkwood)
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The mvebu PCI port parsing is weak due to:
1) allocations via kasprintf() were not cleaned up when we encounter an
error or decide to skip the port.
2) kasprintf() wasn't checked for failure.
3) of_get_named_gpio_flags() returns EPROBE_DEFER if the GPIO is not
present, not devm_gpio_request_one().
4) the of_node was not being put when terminating the loop.
Fix these oversights.
Tested-by: Willy Tarreau <w@1wt.eu> (Iomega iConnect Kirkwood, MiraBox Armada 370)
Tested-by: Andrew Lunn <andrew@lunn.ch> (D-Link DIR664 Kirkwood)
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Move the PCIe port parsing and resource claiming to a separate function in
preparation to add proper cleanup of claimed resources.
Tested-by: Willy Tarreau <w@1wt.eu> (Iomega iConnect Kirkwood, MiraBox Armada 370)
Tested-by: Andrew Lunn <andrew@lunn.ch> (D-Link DIR664 Kirkwood)
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Use the port->name string which we previously formatted when referring to
the name of a port, rather than manually creating the port name each time.
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP)
Tested-by: Andrew Lunn <andrew@lunn.ch> (Kirkwood DIR665)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
If we have a missing required property, report the full node name rather
than a vague "PCIe DT node" statement. This allows the exact node in error
to be identified immediately.
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP)
Tested-by: Andrew Lunn <andrew@lunn.ch> (Kirkwood DIR665)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Rather than using for_each_child_of_node() and testing each child's
availability, use the for_each_available_child_of_node() helper instead.
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP)
Tested-by: Andrew Lunn <andrew@lunn.ch> (Kirkwood DIR665)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Rather than open-coding of_get_available_child_count(), use the provided
helper instead.
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP)
Tested-by: Andrew Lunn <andrew@lunn.ch> (Kirkwood DIR665)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The idea that you can arbitarily read 32-bits from PCI configuration space,
modify a sub-field (like the command register) and write it back without
consequence is deeply flawed.
Status registers (such as the status register, PCIe device status register,
etc) contain status bits which are read, write-one-to-clear.
What this means is that reading 32-bits from the command register,
modifying the command register, and then writing it back has the effect of
clearing any status bits that were indicating at that time. Same for the
PCIe device control register clearing bits in the PCIe device status
register.
Since the Armada chips support byte, 16-bit and 32-bit accesses to the
registers (unless otherwise stated) and the PCI configuration data register
does not specify otherwise, it seems logical that the chip can indeed
generate the proper configuration access cycles down to byte level.
Testing with an ASM1062 PCIe to SATA mini-PCIe card on Armada 388. PCIe
capability at 0x80, DevCtl at 0x88, DevSta at 0x8a.
Before:
/# setpci -s 1:0.0 0x88.l - DevSta: CorrErr+
00012810
/# setpci -s 1:0.0 0x88.w=0x2810 - Write DevCtl only
/# setpci -s 1:0.0 0x88.l - CorrErr cleared - FAIL
00002810
After:
/# setpci -s 1:0.0 0x88.l - DevSta: CorrErr+
00012810
/# setpci -s 1:0.0 0x88.w=0x2810 - check DevCtl only write
/# setpci -s 1:0.0 0x88.l - CorErr remains set
00012810
/# setpci -s 1:0.0 0x88.w=0x281f - check DevCtl write works
/# setpci -s 1:0.0 0x88.l - devctl field updated
0001281f
/# setpci -s 1:0.0 0x8a.w=0xffff - clear DevSta
/# setpci -s 1:0.0 0x88.l - CorrErr now cleared
0000281f
/# setpci -s 1:0.0 0x88.w=0x2810 - restore DevCtl
/# setpci -s 1:0.0 0x88.l - check
00002810
[bhelgaas: changelog]
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP)
Tested-by: Andrew Lunn <andrew@lunn.ch> (Kirkwood DIR665)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
PCI requires reads to reserved or unimplemented configuration space to
return zero and complete normally (see PCI r3.0, sec 6.1). However, the
root port software implementation was returning 0xfffffff and
PCIBIOS_BAD_REGISTER_NUMBER.
Return zero when reading reserved or unimplemented config space.
[bhelgaas: changelog]
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> (Armada XP GP)
Tested-by: Andrew Lunn <andrew@lunn.ch> (Kirkwood DIR665)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
If the bus is being configured with a bus-range that does not start at
zero, pass that starting bus number to pci_scan_root_bus(). Passing the
incorrect value of zero causes attempted config accesses outside of the
supported range, which cascades to an OOPs spew and eventual kernel panic.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Will Deacon <will.deacon@arm.com>
The generic driver kept a global struct pci_ops ("gen_pci_ops") which it
patched with the .map_bus() method appropriate for the bus device. This is
a problem when we have two different types of bus devices: the .map_bus()
method for the last device probed clobbers the method for previous devices.
The result is that only the last bus device probed has the correct
.map_bus(), and the others fail.
Move the struct pci_ops into the bus-specific structure and initialize a
pointer to it when the bus device is probed.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Will Deacon <will.deacon@arm.com>
63692df103 ("PCI: Allow numa_node override via sysfs") didn't check that
the numa node provided by userspace is valid. Passing a node number too
high would attempt to access invalid memory and trigger a kernel panic.
Fixes: 63692df103 ("PCI: Allow numa_node override via sysfs")
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.19+
After 8d63bc7bea ("PCI/MSI: pci-xgene-msi: Get rid of struct
msi_controller"), it is no longer required to assign msi_controller for
X-Gene PCIe host bridge to support MSI.
Remove this unnecessary code. This also avoids a warning message ("failed
to enable MSI") during boot.
[bhelgaas: changelog]
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Tanmay Inamdar <tinamdar@apm.com>
Improve the link detection logic by explicitly querying the link status
register to ensure link is active.
Also force class to PCI_CLASS_BRIDGE_PCI (0x0604) through the host
configuration space register.
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Anup Patel <anup.patel@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
The current reset logic does not always properly reset the device. For
example, in the case when the perst_b signal is already de-asserted in the
bootloader, the current reset logic fails to trigger a proper assert ->
de-assert reset sequence.
Fix the issue by always triggering the proper reset sequence.
Also explicitly select the desired reset source, i.e., perst_b, and reduce
the wait time after the device comes out of reset from 250 ms to 100 ms,
based on recommendation from the ASIC team.
Tested-by: Vladimir Dreizin <vdreizin@broadcom.com>
Tested-by: Darren Edamura <dedamura@broadcom.com>
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vladimir Dreizin <vdreizin@broadcom.com>
Reviewed-by: Trac Hoang <trhoang@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
After 459a07721c ("PCI: Build setup-irq.o for arm64"), we build
setup-irq.o for arm64, so we can use pci_fixup_irqs() on both arm and
arm64.
Remove the "#ifdef CONFIG_ARM" around the call to pci_fixup_irqs().
[bhelgaas: changelog]
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Resource management
- Revert pci_read_bridge_bases() unification (Bjorn Helgaas)
- Clear IORESOURCE_UNSET when clipping a bridge window (Bjorn Helgaas)
MSI
- Fix MSI IRQ domains for VFs on virtual buses (Alex Williamson)
Renesas R-Car host bridge driver
- Add R8A7794 support (Sergei Shtylyov)
Miscellaneous
- Fix devfn for VPD access through function 0 (Alex Williamson)
- Use function 0 VPD only for identical functions (Alex Williamson)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=f4c3
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.3-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for things we merged for v4.3 (VPD, MSI, and bridge
window management), and a new Renesas R8A7794 SoC device ID.
Details:
Resource management:
- Revert pci_read_bridge_bases() unification (Bjorn Helgaas)
- Clear IORESOURCE_UNSET when clipping a bridge window (Bjorn
Helgaas)
MSI:
- Fix MSI IRQ domains for VFs on virtual buses (Alex Williamson)
Renesas R-Car host bridge driver:
- Add R8A7794 support (Sergei Shtylyov)
Miscellaneous:
- Fix devfn for VPD access through function 0 (Alex Williamson)
- Use function 0 VPD only for identical functions (Alex Williamson)"
* tag 'pci-v4.3-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: rcar: Add R8A7794 support
PCI: Use function 0 VPD for identical functions, regular VPD for others
PCI: Fix devfn for VPD access through function 0
PCI/MSI: Fix MSI IRQ domains for VFs on virtual buses
PCI: Clear IORESOURCE_UNSET when clipping a bridge window
PCI: Revert "PCI: Call pci_read_bridge_bases() from core instead of arch code"
Section 3.2 "Device Runtime Power Management" of pci.txt has become
outdated, so update it to correctly reflect the current code flow.
Also update the comment in local_pci_probe() to document the fact
that pm_runtime_put_noidle() is not the only runtime PM helper
function that can be used to decrement the device's runtime PM
usage counter in .probe().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Add a #define for PCIE_PHY_RX_ASIC_OUT_VALID and use it instead of a
hardcoded value.
[bhelgaas: drop PCIE_PHY_DEBUG_R0_LTSSM_MASK; updated in future patch]
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
When devm_request_irq() fails, imx6_add_pcie_port() should return the real
error code instead of always returning -ENODEV.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Add Renesas R8A7794 SoC support to the Renesas R-Car gen2 PCI driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
932c435cab ("PCI: Add dev_flags bit to access VPD through function 0")
added PCI_DEV_FLAGS_VPD_REF_F0. Previously, we set the flag on every
non-zero function of quirked devices. If a function turned out to be
different from function 0, i.e., it had a different class, vendor ID, or
device ID, the flag remained set but we didn't make VPD accessible at all.
Flip this around so we only set PCI_DEV_FLAGS_VPD_REF_F0 for functions that
are identical to function 0, and allow regular VPD access for any other
functions.
[bhelgaas: changelog, stable tag]
Fixes: 932c435cab ("PCI: Add dev_flags bit to access VPD through function 0")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Myron Stowe <myron.stowe@redhat.com>
Acked-by: Mark Rustad <mark.d.rustad@intel.com>
CC: stable@vger.kernel.org
Commit 932c435cab ("PCI: Add dev_flags bit to access VPD through function
0") passes PCI_SLOT(devfn) for the devfn parameter of pci_get_slot().
Generally this works because we're fairly well guaranteed that a PCIe
device is at slot address 0, but for the general case, including
conventional PCI, it's incorrect. We need to get the slot and then convert
it back into a devfn.
Fixes: 932c435cab ("PCI: Add dev_flags bit to access VPD through function 0")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Myron Stowe <myron.stowe@redhat.com>
Acked-by: Mark Rustad <mark.d.rustad@intel.com>
CC: stable@vger.kernel.org
SR-IOV creates a virtual bus where bus->self is NULL. When we add VFs and
scan for an MSI domain, pci_set_bus_msi_domain() dereferences bus->self,
which causes a kernel NULL pointer dereference oops.
Scan up to the parent bus until we find a real bridge where we can get the
MSI domain.
[bhelgaas: changelog]
Fixes: 44aa0c657e ("PCI/MSI: Add hooks to populate the msi_domain field")
Tested-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
MSI is broken on SiS 761 chipset at least on PC Chips A31G board. No
interrupts are delivered once MSI is enabled for a device. This causes
hang on X11 start with a nVidia card installed (with nouveau driver).
Disable MSI completely for this chipset.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
If pci_assign_resource() fails to assign space for a BAR, we may restore
the BAR to whatever firmware left there at boot-time (this depends on
whether the arch implements pcibios_retrieve_fw_addr()). The messages we
print are not as useful as they could be:
pci 0000:00:01.0: BAR 15: assigned [mem 0xc0000000-0xc01fffff 64bit pref]
pci 0000:01:00.0: BAR 0: no space for [mem size 0x10000000 pref]
pci 0000:01:00.0: BAR 0: trying firmware assignment [mem size 0x10000000 pref]
pci 0000:01:00.0: BAR 0: [mem size 0x10000000 pref] conflicts with PCI Bus 0000:00 [mem 0xc0000000-0xffffffff window]
The last two lines should contain the actual BAR address, not the size.
Clear IORESOURCE_UNSET so we print the address. If requesting the
firmware-assigned resource fails, mark it IORESOURCE_UNSET again.
This is a cosmetic change to clarify the message: previously, if
pci_revert_fw_address() succeeded, pci_assign_resource() cleared
IORESOURCE_UNSET anyway, so this isn't really a functional change.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491#c50
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
c770cb4cb5 ("PCI: Mark invalid BARs as unassigned") sets IORESOURCE_UNSET
if we fail to claim a resource. If we tried to claim a bridge window,
failed, clipped the window, and tried to claim the clipped window, we
failed again because of IORESOURCE_UNSET:
pci_bus 0000:00: root bus resource [mem 0xc0000000-0xffffffff window]
pci 0000:00:01.0: can't claim BAR 15 [mem 0xbdf00000-0xddefffff 64bit pref]: no compatible bridge window
pci 0000:00:01.0: [mem size 0x20000000 64bit pref] clipped to [mem size 0x1df00000 64bit pref]
pci 0000:00:01.0: bridge window [mem size 0x1df00000 64bit pref]
pci 0000:00:01.0: can't claim BAR 15 [mem size 0x1df00000 64bit pref]: no address assigned
The 00:01.0 window started as [mem 0xbdf00000-0xddefffff 64bit pref]. That
starts before the host bridge window [mem 0xc0000000-0xffffffff window], so
we clipped the 00:01.0 window to [mem 0xc0000000-0xddefffff 64bit pref].
But we left it marked IORESOURCE_UNSET, so the second claim failed when it
should have succeeded.
This means downstream devices will also fail for lack of resources, e.g.,
in the bugzilla below,
radeon 0000:01:00.0: Fatal error during GPU init
Clear IORESOURCE_UNSET when we clip a bridge window. Also clear
IORESOURCE_UNSET in our copy of the unclipped window so we can see exactly
what the original window was and how it now fits inside the upstream
window.
Fixes: c770cb4cb5 ("PCI: Mark invalid BARs as unassigned")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491#c47
Based-on-patch-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Based-on-patch-by: Yinghai Lu <yinghai@kernel.org>
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
CC: stable@vger.kernel.org # v4.1+
In store_remove_id(), set the default return value to -ENODEV, and
overwrite it with the input buffer size if we find a matching list entry.
Then we don't need to test whether to return an error or the count.
No functional change.
[bhelgaas: changelog]
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Make get_msi_addr() return phys_addr_t, not u32. This allows the MSI
target address to be above 4GB for 64bit or PAE systems.
No functional change for the current 32bit platform users as phys_addr_t
maps to u32 for them.
[bhelgaas: changelog]
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Implement multivector MSI IRQ setup. This allows to set up and use multiple
MSI IRQs per device.
[bhelgaas: changelog, use -EINVAL instead of -ENOSYS]
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Factor out the PCI MSI message setup from the single MSI setup function.
This will be reused by the multivector MSI setup.
No functional change yet.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
Add a msi_controller setup_irqs() method so MSI chip providers can
implement their own multivector MSI setup.
[bhelgaas: changelog]
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pratyush Anand <pratyush.anand@gmail.com>
The value under PORT_LOGIC_LINK_WIDTH_MASK is 0x1, 0x2, 0x4, 0x8. In IP
v4.2, bits [16:8] are defined for NUM_OF_LANES. But in IP v4.4, bits[12:8]
are defined for NUM_OF_LANES, bits [16:13] are for other usages (bit 16 is
AUTO_LANE_FLIP_CTRL_EN, bits [15:13] are PRE_DET_LANE).
As there is no conflict about NUM_OF_LANES between v4.2 and v4.4, change
the mask value to avoid future problems.
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
When pci-host-generic looks for the probe-only property, it seems to trust
the DT to be correctly written, and assumes that there is a parameter to
the property.
Unfortunately, this is not always the case, and some firmware expose this
property naked. The driver ends up making a decision based on whatever the
property pointer points to, which is likely to be junk.
Switch to the common of_pci.c implementation that doesn't suffer from this
problem.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Will Deacon <will.deacon@arm.com>
AER errors might be recorded when powering-on devices. These errors can be
ignored, so firmware usually clears them before the OS enumerates devices.
However, firmware is not involved when devices are added via hotplug, so
the OS may discover power-up errors that should be ignored. The same may
happen when powering up devices when resuming after suspend.
Clear the AER error status registers during enumeration and resume.
[bhelgaas: changelog, remove repetitive comments]
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Revert dff22d2054 ("PCI: Call pci_read_bridge_bases() from core instead
of arch code").
Reading PCI bridge windows is not arch-specific in itself, but there is PCI
core code that doesn't work correctly if we read them too early. For
example, Hannes found this case on an ARM Freescale i.mx6 board:
pci_bus 0000:00: root bus resource [mem 0x01000000-0x01efffff]
pci 0000:00:00.0: PCI bridge to [bus 01-ff]
pci 0000:00:00.0: BAR 8: no space for [mem size 0x01000000] (mem window)
pci 0000:01:00.0: BAR 2: failed to assign [mem size 0x00200000]
pci 0000:01:00.0: BAR 1: failed to assign [mem size 0x00004000]
pci 0000:01:00.0: BAR 0: failed to assign [mem size 0x00000100]
The 00:00.0 mem window needs to be at least 3MB: the 01:00.0 device needs
0x204100 of space, and mem windows are megabyte-aligned.
Bus sizing can increase a bridge window size, but never *decrease* it (see
d65245c329 ("PCI: don't shrink bridge resources")). Prior to
dff22d2054, ARM didn't read bridge windows at all, so the "original size"
was zero, and we assigned a 3MB window.
After dff22d2054, we read the bridge windows before sizing the bus. The
firmware programmed a 16MB window (size 0x01000000) in 00:00.0, and since
we never decrease the size, we kept 16MB even though we only needed 3MB.
But 16MB doesn't fit in the host bridge aperture, so we failed to assign
space for the window and the downstream devices.
I think this is a defect in the PCI core: we shouldn't rely on the firmware
to assign sensible windows.
Ray reported a similar problem, also on ARM, with Broadcom iProc.
Issues like this are too hard to fix right now, so revert dff22d2054.
Reported-by: Hannes <oe5hpm@gmail.com>
Reported-by: Ray Jui <rjui@broadcom.com>
Link: http://lkml.kernel.org/r/CAAa04yFQEUJm7Jj1qMT57-LG7ZGtnhNDBe=PpSRa70Mj+XhW-A@mail.gmail.com
Link: http://lkml.kernel.org/r/55F75BB8.4070405@broadcom.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
VF BARs are read-only zero, so updating VF BARs will not have any effect.
See the SR-IOV spec r1.1, sec 3.4.1.11.
Don't update VF BARs in pci_restore_bars().
This avoids spurious "BAR %d: error updating" messages that we see when
doing vfio pass-through after 6eb7018705 ("vfio-pci: Move idle devices to
D3hot power state").
[bhelgaas: changelog, fix whitespace]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
There are two kexec load syscalls, kexec_load another and kexec_file_load.
kexec_file_load has been splited as kernel/kexec_file.c. In this patch I
split kexec_load syscall code to kernel/kexec.c.
And add a new kconfig option KEXEC_CORE, so we can disable kexec_load and
use kexec_file_load only, or vice verse.
The original requirement is from Ted Ts'o, he want kexec kernel signature
being checked with CONFIG_KEXEC_VERIFY_SIG enabled. But kexec-tools use
kexec_load syscall can bypass the checking.
Vivek Goyal proposed to create a common kconfig option so user can compile
in only one syscall for loading kexec kernel. KEXEC/KEXEC_FILE selects
KEXEC_CORE so that old config files still work.
Because there's general code need CONFIG_KEXEC_CORE, so I updated all the
architecture Kconfig with a new option KEXEC_CORE, and let KEXEC selects
KEXEC_CORE in arch Kconfig. Also updated general kernel code with to
kexec_load syscall.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Dave Young <dyoung@redhat.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Petr Tesarik <ptesarik@suse.cz>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Josh Boyer <jwboyer@fedoraproject.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull parisc updates from Helge Deller:
"The most important changes in this patchset are:
- re-enable 64bit PCI bus addresses which were temporarily disabled
for PA-RISC in kernel 4.2
- fix the 64bit CAS operation in the LWS path which now enables us to
enable the 64bit gcc atomic builtins even on 32bit userspace with
64bit kernel
- fix a long-standing bug which sometimes crashed kernel at bootup
while serial interrupt wasn't registered yet"
* 'parisc-4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Use platform_device_register_simple("rtc-generic")
parisc: Drop CONFIG_SMP around update_cr16_clocksource()
parisc: Use double word condition in 64bit CAS operation
parisc: Filter out spurious interrupts in PA-RISC irq handler
parisc: Additionally check for in_atomic() in page fault handler
PCI,parisc: Enable 64-bit bus addresses on PA-RISC
parisc: Define ioremap_uc and ioremap_wc
1/ Introduce ZONE_DEVICE and devm_memremap_pages() as a generic
mechanism for adding device-driver-discovered memory regions to the
kernel's direct map. This facility is used by the pmem driver to
enable pfn_to_page() operations on the page frames returned by DAX
('direct_access' in 'struct block_device_operations'). For now, the
'memmap' allocation for these "device" pages comes from "System
RAM". Support for allocating the memmap from device memory will
arrive in a later kernel.
2/ Introduce memremap() to replace usages of ioremap_cache() and
ioremap_wt(). memremap() drops the __iomem annotation for these
mappings to memory that do not have i/o side effects. The
replacement of ioremap_cache() with memremap() is limited to the
pmem driver to ease merging the api change in v4.3. Completion of
the conversion is targeted for v4.4.
3/ Similar to the usage of memcpy_to_pmem() + wmb_pmem() in the pmem
driver, update the VFS DAX implementation and PMEM api to provide
persistence guarantees for kernel operations on a DAX mapping.
4/ Convert the ACPI NFIT 'BLK' driver to map the block apertures as
cacheable to improve performance.
5/ Miscellaneous updates and fixes to libnvdimm including support
for issuing "address range scrub" commands, clarifying the optimal
'sector size' of pmem devices, a clarification of the usage of the
ACPI '_STA' (status) property for DIMM devices, and other minor
fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=o57/
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"This update has successfully completed a 0day-kbuild run and has
appeared in a linux-next release. The changes outside of the typical
drivers/nvdimm/ and drivers/acpi/nfit.[ch] paths are related to the
removal of IORESOURCE_CACHEABLE, the introduction of memremap(), and
the introduction of ZONE_DEVICE + devm_memremap_pages().
Summary:
- Introduce ZONE_DEVICE and devm_memremap_pages() as a generic
mechanism for adding device-driver-discovered memory regions to the
kernel's direct map.
This facility is used by the pmem driver to enable pfn_to_page()
operations on the page frames returned by DAX ('direct_access' in
'struct block_device_operations').
For now, the 'memmap' allocation for these "device" pages comes
from "System RAM". Support for allocating the memmap from device
memory will arrive in a later kernel.
- Introduce memremap() to replace usages of ioremap_cache() and
ioremap_wt(). memremap() drops the __iomem annotation for these
mappings to memory that do not have i/o side effects. The
replacement of ioremap_cache() with memremap() is limited to the
pmem driver to ease merging the api change in v4.3.
Completion of the conversion is targeted for v4.4.
- Similar to the usage of memcpy_to_pmem() + wmb_pmem() in the pmem
driver, update the VFS DAX implementation and PMEM api to provide
persistence guarantees for kernel operations on a DAX mapping.
- Convert the ACPI NFIT 'BLK' driver to map the block apertures as
cacheable to improve performance.
- Miscellaneous updates and fixes to libnvdimm including support for
issuing "address range scrub" commands, clarifying the optimal
'sector size' of pmem devices, a clarification of the usage of the
ACPI '_STA' (status) property for DIMM devices, and other minor
fixes"
* tag 'libnvdimm-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (34 commits)
libnvdimm, pmem: direct map legacy pmem by default
libnvdimm, pmem: 'struct page' for pmem
libnvdimm, pfn: 'struct page' provider infrastructure
x86, pmem: clarify that ARCH_HAS_PMEM_API implies PMEM mapped WB
add devm_memremap_pages
mm: ZONE_DEVICE for "device memory"
mm: move __phys_to_pfn and __pfn_to_phys to asm/generic/memory_model.h
dax: drop size parameter to ->direct_access()
nd_blk: change aperture mapping from WC to WB
nvdimm: change to use generic kvfree()
pmem, dax: have direct_access use __pmem annotation
dax: update I/O path to do proper PMEM flushing
pmem: add copy_from_iter_pmem() and clear_pmem()
pmem, x86: clean up conditional pmem includes
pmem: remove layer when calling arch_has_wmb_pmem()
pmem, x86: move x86 PMEM API to new pmem.h header
libnvdimm, e820: make CONFIG_X86_PMEM_LEGACY a tristate option
pmem: switch to devm_ allocations
devres: add devm_memremap
libnvdimm, btt: write and validate parent_uuid
...
Commit 3a9ad0b ("PCI: Add pci_bus_addr_t") unconditionally introduced usage of
64-bit PCI bus addresses on all 64-bit platforms which broke PA-RISC.
It turned out that due to enabling the 64-bit addresses, the PCI logic decided
to use the GMMIO instead of the LMMIO region. This commit simply disables
registering the GMMIO and thus we fall back to use the LMMIO region as before.
Reverts commit 45ea2a5fed
("PCI: Don't use 64-bit bus addresses on PA-RISC")
To: linux-parisc@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Meelis Roos <mroos@linux.ee>
Cc: stable@vger.kernel.org # v3.19+
Signed-off-by: Helge Deller <deller@gmx.de>
Pull irq updates from Thomas Gleixner:
"This updated pull request does not contain the last few GIC related
patches which were reported to cause a regression. There is a fix
available, but I let it breed for a couple of days first.
The irq departement provides:
- new infrastructure to support non PCI based MSI interrupts
- a couple of new irq chip drivers
- the usual pile of fixlets and updates to irq chip drivers
- preparatory changes for removal of the irq argument from interrupt
flow handlers
- preparatory changes to remove IRQF_VALID"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (129 commits)
irqchip/imx-gpcv2: IMX GPCv2 driver for wakeup sources
irqchip: Add bcm2836 interrupt controller for Raspberry Pi 2
irqchip: Add documentation for the bcm2836 interrupt controller
irqchip/bcm2835: Add support for being used as a second level controller
irqchip/bcm2835: Refactor handle_IRQ() calls out of MAKE_HWIRQ
PCI: xilinx: Fix typo in function name
irqchip/gic: Ensure gic_cpu_if_up/down() programs correct GIC instance
irqchip/gic: Only allow the primary GIC to set the CPU map
PCI/MSI: pci-xgene-msi: Consolidate chained IRQ handler install/remove
unicore32/irq: Prepare puv3_gpio_handler for irq argument removal
tile/pci_gx: Prepare trio_handle_level_irq for irq argument removal
m68k/irq: Prepare irq handlers for irq argument removal
C6X/megamode-pic: Prepare megamod_irq_cascade for irq argument removal
blackfin: Prepare irq handlers for irq argument removal
arc/irq: Prepare idu_cascade_isr for irq argument removal
sparc/irq: Use access helper irq_data_get_affinity_mask()
sparc/irq: Use helper irq_data_get_irq_handler_data()
parisc/irq: Use access helper irq_data_get_affinity_mask()
mn10300/irq: Use access helper irq_data_get_affinity_mask()
irqchip/i8259: Prepare i8259_irq_dispatch for irq argument removal
...
Here's our branch of ARM64 contents for this merge window.
Most of this is DT contents for new SoCs (or those who have seen new
device support added). Maybe we should stop separating out the arm64
contents here to avoid the kind of internal conflicts as we got this
time around, where 32- and 64-bit contents conflicted.
Anyhow, on the actual contents:
New SoCs:
- Broadcom North Star 2 (ns2)
- Marvell Berlin4CT
- Mediatek MT6795
- Rockchip RK3368
In addition, there are enhancements for the following platforms:
- Mediatek MT8173: cpuidle-dt updates, misc other additions
- ZyncMP: A bunch of devices added to the existing DTSI
- Qualcomm MSM8916 and APQ8016 updates for USB, etc.
+ A handful of other updates for various platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJV5N8IAAoJEIwa5zzehBx3qt0P/ju6RvgS2vUDk6QxjBvzp2oN
daXOj73Nefe4Qef7GT5k5K1hLFVflKmesIDqG/eTfGTDSjMjQaJufZTKGh+5arLQ
28XAm897gsjt+NVzEgdkG1QD8GIlfth+S3ylh/nLx+zOMTz353dMgpNY0o3eWVFr
TYq+x6u4UFEmBFvkYm7P9ONfqKKiaO2pqjsA41SfKao0c8+kwrB5jWO2m4DaYqhC
Mj6ug8HoQLJk+ZpbhcsUDD4tAMIL0VJWl446LLCsd/tk81J05K95vPCTEdyGRu0U
dwe0W0PgODPMqyYTXteVdOuT1n7CYFlySAKfJUx4yW4w9Y5hHbB6sHYRHHt6unny
Ynn5u2xIUHKaqiOeShDHV433ssCB+1tgBefoAVPqY2kYC8eCP46zrieVwZip4/KA
rEldc1c+tCUYROe39F4ljg3I4wFNtBhfn3JCoocvbljmMSro5MD3zf1n8p21C6GV
vCidRbIXHVd89FALFL/1r1vuMAlaF6TD/FyxYVrJXgr8LTj5gak93/O5WpsYam6c
GwiTnykz+3eHvDi7xrhsohCHptvE7TnBSNhfkxsngFoJr3evAbU3B4qJKLzrZCvf
KHVIoSylEl+4+M6VISowid6NL4ADc8mNeHXfGxFHVBEfnK/tH3VySM4hV0reAh4m
NR+TX15zqfF4uudoAqlC
=SZR9
-----END PGP SIGNATURE-----
Merge tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC 64-bit changes from Olof Johansson:
"Here's our branch of ARM64 contents for this merge window.
Most of this is DT contents for new SoCs (or those who have seen new
device support added). Maybe we should stop separating out the arm64
contents here to avoid the kind of internal conflicts as we got this
time around, where 32- and 64-bit contents conflicted.
Anyhow, on the actual contents:
New SoCs:
- Broadcom North Star 2 (ns2)
- Marvell Berlin4CT
- Mediatek MT6795
- Rockchip RK3368
In addition, there are enhancements for the following platforms:
- Mediatek MT8173: cpuidle-dt updates, misc other additions
- ZyncMP: A bunch of devices added to the existing DTSI
- Qualcomm MSM8916 and APQ8016 updates for USB, etc.
+ a handful of other updates for various platforms"
* tag 'armsoc-arm64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (47 commits)
ARM64: dts: vexpress: Use assigned-clock-parents for sp810
ARM64: dts: mt6795: enable basic SMP bringup for MT6795
arm64: Enable Marvell Berlin SoC family in defconfig
arm64: Enable Marvell Berlin SoC family in Kconfig
arm64: dts: Add dts files for Marvell Berlin4CT SoC
ARM64: zynqmp: Move SPI nodes to the right location
ARM64: zynqmp: Move uart and ttcs to the right location
ARM64: zynqmp: Enable spi flashes on ep108
ARM64: zynqmp: Add eeprom memories on i2c bus
ARM64: zynqmp: Enable sdhci on ep108
ARM64: zynqmp: Enable watchdog on ep108
ARM64: zynqmp: Add DWC3 usb support
ARM64: zynqmp: Add SMMU support
ARM64: zynqmp: Add CANs node for platform
ARM64: zynqmp: Use zynqmp specific compatible string for gpio
devicetree: xilinx: zynqmp: add sata node
PCI: iproc: Fix BCMA dependency in Kconfig
arm64: dts: Add Broadcom North Star 2 support
arm64: Add Broadcom iProc family support
PCI: iproc: Fix ARM64 dependency in Kconfig
...
Pull x86 mm updates from Ingo Molnar:
"The dominant change in this cycle was the continued work to isolate
kernel drivers from MTRR legacies: this tree gets rid of all kernel
internal driver interfaces to MTRRs (mostly by rewriting it to proper
PAT interfaces), the only access left is the /proc/mtrr ABI.
This work was done by Luis R Rodriguez.
There's also some related PCI interface additions for which I've
Cc:-ed Bjorn"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
x86/mm/mtrr: Remove kernel internal MTRR interfaces: unexport mtrr_add() and mtrr_del()
s390/io: Add pci_iomap_wc() and pci_iomap_wc_range()
drivers/dma/iop-adma: Use dma_alloc_writecombine() kernel-style
drivers/video/fbdev/vt8623fb: Use arch_phys_wc_add() and pci_iomap_wc()
drivers/video/fbdev/s3fb: Use arch_phys_wc_add() and pci_iomap_wc()
drivers/video/fbdev/arkfb.c: Use arch_phys_wc_add() and pci_iomap_wc()
PCI: Add pci_iomap_wc() variants
drivers/video/fbdev/gxt4500: Use pci_ioremap_wc_bar() to map framebuffer
drivers/video/fbdev/kyrofb: Use arch_phys_wc_add() and pci_ioremap_wc_bar()
drivers/video/fbdev/i740fb: Use arch_phys_wc_add() and pci_ioremap_wc_bar()
PCI: Add pci_ioremap_wc_bar()
x86/mm: Make kernel/check.c explicitly non-modular
x86/mm/pat: Make mm/pageattr[-test].c explicitly non-modular
x86/mm/pat: Add comments to cachemode translation tables
arch/*/io.h: Add ioremap_uc() to all architectures
drivers/video/fbdev/atyfb: Use arch_phys_wc_add() and ioremap_wc()
drivers/video/fbdev/atyfb: Replace MTRR UC hole with strong UC
drivers/video/fbdev/atyfb: Clarify ioremap() base and length used
drivers/video/fbdev/atyfb: Carve out framebuffer length fudging into a helper
x86/mm, asm-generic: Add IOMMU ioremap_uc() variant default
...
Commit 1851617cd2 ("PCI/MSI: Disable MSI at enumeration even if kernel
doesn't support MSI") changed the location of the code that initialises
dev->msi_cap/msix_cap and then disables MSI/MSI-X interrupts at PCI
probe time in devices that have this flag set. It moved the code from
pci_msi_init_pci_dev() to a new function named pci_msi_setup_pci_dev(),
called by pci_setup_device().
The pseries PCI probing code does not call pci_setup_device(), so since
the aforementioned commit the function pci_msi_setup_pci_dev() is not
called and MSI/MSI-X interrupts are left enabled. Additionally because
dev->msi_cap/msix_cap are not initialised no driver can ever enable
MSI/MSI-X.
To fix this, the pseries PCI probe should manually call
pci_msi_setup_pci_dev(), so this patch makes it non-static.
Fixes: 1851617cd2 ("PCI/MSI: Disable MSI at enumeration even if kernel doesn't support MSI")
[mpe: Update change log to mention dev->msi_cap/msix_cap]
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This lets drivers take advantage of PAT when available. It
should help with the transition of converting video drivers over
to ioremap_wc() to help with the goal of eventually using
_PAGE_CACHE_UC over _PAGE_CACHE_UC_MINUS on x86 on
ioremap_nocache(), see:
de33c442ed ("x86 PAT: fix performance drop for glx, use UC minus for ioremap(), ioremap_nocache() and pci_mmap_page_range()")
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: <syrjala@sci.fi>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Antonino Daplas <adaplas@gmail.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Davidlohr Bueso <dbueso@suse.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Suresh Siddha <sbsiddha@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Ville Syrjälä <syrjala@sci.fi>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: airlied@linux.ie
Cc: benh@kernel.crashing.org
Cc: dan.j.williams@intel.com
Cc: konrad.wilk@oracle.com
Cc: linux-fbdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Cc: mst@redhat.com
Cc: vinod.koul@intel.com
Cc: xen-devel@lists.xensource.com
Link: http://lkml.kernel.org/r/1440443613-13696-2-git-send-email-mcgrof@do-not-panic.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On multi-function JMicron SATA/PATA/AHCI devices, the PATA controller at
function 1 doesn't work if it is powered on before the SATA controller at
function 0. The result is that PATA doesn't work after resume, and we
print messages like this:
pata_jmicron 0000:02:00.1: Refused to change power state, currently in D3
irq 17: nobody cared (try booting with the "irqpoll" option)
Async resume was introduced in v3.15 by 76569faa62 ("PM / sleep:
Asynchronous threads for resume_noirq"). Prior to that, we powered on
the functions in order, so this problem shouldn't happen.
e6b7e41cdd ("ata: Disabling the async PM for JMicron chip 363/361")
solved the problem for JMicron 361 and 363 devices. With async suspend
disabled, we always power on function 0 before function 1.
Barto then reported the same problem with a JMicron 368 (see comment #57 in
the bugzilla).
Rather than extending the blacklist piecemeal, disable async suspend for
all JMicron multi-function SATA/PATA/AHCI devices.
This quirk could stay in the ahci and pata_jmicron drivers, but it's likely
the problem will occur even if pata_jmicron isn't loaded until after the
suspend/resume. Making it a PCI quirk ensures that we'll preserve the
power-on order even if the drivers aren't loaded.
[bhelgaas: changelog, limit to multi-function, limit to IDE/ATA]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=81551
Reported-and-tested-by: Barto <mister.freeman@laposte.net>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.15+
* pci/host-dra7xx:
PCI: dra7xx: Remove unneeded use of IS_ERR_VALUE()
* pci/host-imx6:
PCI: imx6: Simplify a trivial if-return sequence
* pci/host-spear:
PCI: spear: Use BUG_ON() instead of condition followed by BUG()
Firmware typically configures the PCIe fabric with a consistent Max Payload
Size setting based on the devices present at boot. A hot-added device
typically has the power-on default MPS setting (128 bytes), which may not
match the fabric.
The previous Linux default, in the absence of any "pci=pcie_bus_*" options,
was PCIE_BUS_TUNE_OFF, in which we never touch MPS, even for hot-added
devices.
Add a new default setting, PCIE_BUS_DEFAULT, in which we make sure every
device's MPS setting matches the upstream bridge. This makes it more
likely that a hot-added device will work in a system with optimized MPS
configuration.
Note that if we hot-add a device that only supports 128-byte MPS, it still
likely won't work because we don't reconfigure the rest of the fabric.
Booting with "pci=pcie_bus_peer2peer" is a workaround for this because it
sets MPS to 128 for everything.
[bhelgaas: changelog, new default, rework for pci_configure_device() path]
Tested-by: Keith Busch <keith.busch@intel.com>
Tested-by: Jordan Hargrave <jharg93@gmail.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Meelis and Helge reported that 3a9ad0b4fd ("PCI: Add pci_bus_addr_t")
caused HPMCs on A500 and hangs on rp5470.
PA-RISC does not set ARCH_DMA_ADDR_T_64BIT, even for 64-bit kernels, so
prior to 3a9ad0b4fd, we always used 32-bit PCI addresses. After
3a9ad0b4fd, we do use 64-bit PCI addresses in 64-bit kernels, and
apparently there's some PA-RISC problem related to them.
Fixes: 3a9ad0b4fd ("PCI: Add pci_bus_addr_t")
Link: http://lkml.kernel.org/r/alpine.LRH.2.11.1507260929000.30065@math.ut.ee
Reported-by: Meelis Roos <mroos@linux.ee>
Reported-by: Helge Deller <deller@gmx.de>
Tested-by: Helge Deller <deller@gmx.de>
Based-on-idea-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
CC: stable@vger.kernel.org # v3.19+
Previously we checked for invalid MPS settings, i.e., a device with MPS
different than its upstream bridge, in pcie_bus_detect_mps(). We only did
this if the arch or hotplug driver called pcie_bus_configure_settings(),
and then only if PCIe bus tuning was disabled (PCIE_BUS_TUNE_OFF).
Move the MPS checking code to pci_configure_device(), so we do it in the
pci_device_add() path for every device.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
of_parse_phandle() returns a device_node pointer with the refcount
incremented. We should dispose of this reference when we're finished.
Drop the reference acquired by of_parse_phandle().
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The pcibios_msi_controller() hook was only implemented by ARM, and it sets
pci_bus->msi now, so it doesn't need this hook anymore.
Remove the unused pcibios_msi_controller() hook.
[bhelgaas: changelog, split into separate patch]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ARM previously stored the msi_controller pointer in its sysdata, struct
pci_sys_data, and implemented pcibios_msi_controller() to retrieve it.
That made PCI host controller drivers specific to ARM because they had to
put the msi_controller pointer in the ARM-specific pci_sys_data.
There is now a generic mechanism, pci_scan_root_bus_msi(), for giving the
msi_controller pointer to the PCI core. Use this for all ARM systems and
for the DesignWare and Xilinx PCI host controller drivers.
This removes an ARM dependency from the DesignWare, DRA7xx, EXYNOS, i.MX6,
Keystone, Layerscape, SPEAr13xx, and Xilinx drivers.
[bhelgaas: changelog, split into separate patch]
Suggested-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
CC: Pratyush Anand <pratyush.anand@gmail.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Simon Horman <horms@verge.net.au>
CC: Russell King <linux@arm.linux.org.uk>
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Michal Simek <michal.simek@xilinx.com>
CC: Marc Zyngier <marc.zyngier@arm.com>
Add a pci_scan_root_bus_msi() interface so an arch can specify the MSI
controller up front. This removes the need for a pcibios callback to set
the MSI controller later.
This is not exported because I'd like to replace the variety of "scan root
bus" interfaces with a single, more extensible interface that can handle
the MSI controller, domain, pci_ops, resources, etc. I hope this interface
is temporary.
[bhelgaas: changelog, split into separate patch]
Suggested-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jingoohan1@gmail.com>
Make pci-host-generic driver (kernel option PCI_HOST_GENERIC) available on
arm64.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ARM64 requires setup-irq.o to provide pci_fixup_irqs() implementation. We
are adding this now to support the pci-host-generic host controller, but we
enable it for ARM64 PCI so that other host controllers can use this as
well.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The generic OF-based host controller driver uses pci_common_init_dev(),
which is ARM-specific and requires the ARM struct hw_pci. The part of
pci_common_init_dev() that is needed is limited and can be done here
without using hw_pci.
Note that the ARM pcibios functions expect the PCI sysdata to be a pointer
to a struct pci_sys_data. Add a struct pci_sys_data as the first element
in struct gen_pci so that when we use a gen_pci pointer as sysdata, it is
also a pointer to a struct pci_sys_data.
Create and scan the root bus directly without using the ARM
pci_common_init_dev() interface.
[bhelgaas: changelog, move pcie_bus_configure_settings() before
pci_bus_add_devices(), combine !PCI_PROBE_ONLY blocks]
Tested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Tested-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Simplify a trivial if-return sequence by combining it with a preceding
function call.
The semantic patch that makes this change is available in
scripts/coccinelle/misc/simple_return.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Lucas Stach <l.stach@pengutronix.de>
Use BUG_ON() instead of an if condition followed by BUG().
The semantic patch that makes this change is available in
scripts/coccinelle/misc/bugon.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Pratyush Anand <pratyush.anand@gmail.com>
There is no need to use the IS_ERR_VALUE() macro for checking the return
value from pm_runtime_* functions.
Test for a negative pm_runtime_get_sync() return value instead of using
IS_ERR_VALUE().
The semantic patch that makes this change is available in
scripts/coccinelle/api/pm_runtime.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Kishon Vijay Abraham I <kishon@ti.com>
We should not assume any particular hardware topology. Commit d0751b98df
("PCI: Add dev->has_secondary_link to track downstream PCIe links") relied
on the assumption that every PCIe hierarchy is rooted at a Root Port. But
we can't rely on any assumption about what hardware we will find; we just
have to deal with the world as it is.
On some platforms, PCIe devices (endpoints, switch upstream ports, etc.)
appear directly on the root bus, and there is no Root Port in the PCI bus
hierarchy. For example, Meelis observed these top-level devices on a
Sparc V245:
0000:02:00.0 PCI bridge to [bus 03-0d] Switch Upstream Port
0001:02:00.0 PCI bridge to [bus 03] PCIe to PCI/PCI-X Bridge
These devices *look* like they have links going upstream, but there really
are no upstream devices.
In set_pcie_port_type(), we used the parent device to figure out which side
of a switch port has a link, so if the parent device did not exist, we
dereferenced a NULL parent pointer.
Check whether the parent device exists before dereferencing it.
Meelis observed this oops on Sparc V245 and T2000. Ben Herrenschmidt says
this is also possible on IBM PowerVM guests on PowerPC.
[bhelgaas: changelog, comment]
Link: http://lkml.kernel.org/r/alpine.LRH.2.20.1508122118210.18637@math.ut.ee
Reported-by: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
There's a typo in commit e39758e0ea in linux-next, which incorrectly
spells "msi_desc_to_pci_sysdata()" as "msi_desc_to_pci_sys_data()" and
causes build failure:
> ../drivers/pci/host/pcie-xilinx.c:235:3: error: implicit declaration
of function 'msi_desc_to_pci_sys_data' [-Werror=implicit-function-declaration]
Fixes: e39758e0ea "PCI: Use helper functions to access fields in struct msi_desc"
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Mark Brown <broonie@kernel.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
Cc: Srikanth Thokala <sthokal@xilinx.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Link: http://lkml.kernel.org/r/1439912763-10645-1-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* pci/host-dra7xx:
ARM: dts: am57xx-evm: Add 'gpios' property with gpio2_8
PCI: dra7xx: Add support to make GPIO drive PERST# line
PCI: dra7xx: Clear MSE bit during suspend so clocks will idle
PCI: dra7xx: Add PM support
PCI: dra7xx: Disable pm_runtime on get_sync failure
* pci/host-iproc:
PCI: iproc: Allow BCMA bus driver to be built as module
PCI: iproc: Add arm64 support
PCI: iproc: Delete unnecessary checks before phy calls
* pci/hotplug:
PCI: pciehp: Remove ignored MRL sensor interrupt events
PCI: pciehp: Remove unused interrupt events
PCI: pciehp: Handle invalid data when reading from non-existent devices
PCI: Hold pci_slot_mutex while searching bus->slots list
PCI: Protect pci_bus->slots with pci_slot_mutex, not pci_bus_sem
PCI: pciehp: Simplify pcie_poll_cmd()
PCI: Use "slot" and "pci_slot" for struct hotplug_slot and struct pci_slot
* pci/iommu:
PCI: Remove pci_ats_enabled()
PCI: Stop caching ATS Invalidate Queue Depth
PCI: Move ATS declarations to linux/pci.h so they're all together
PCI: Clean up ATS error handling
PCI: Use pci_physfn() rather than looking up physfn by hand
PCI: Inline the ATS setup code into pci_ats_init()
PCI: Rationalize pci_ats_queue_depth() error checking
PCI: Reduce size of ATS structure elements
PCI: Embed ATS info directly into struct pci_dev
PCI: Allocate ATS struct during enumeration
iommu/vt-d: Cache PCI ATS state and Invalidate Queue Depth
* pci/irq:
PCI: Kill off set_irq_flags() usage
* pci/virtualization:
PCI: Add ACS quirks for Intel I219-LM/V
Remove pci_ats_enabled(). There are no callers outside the ATS code
itself. We don't need to check ats_cap, because if we don't find an ATS
capability, we'll never set ats_enabled.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Stop caching the Invalidate Queue Depth in struct pci_dev.
pci_ats_queue_depth() is typically called only once per device, and it
returns a fixed value per-device, so callers who need the value frequently
can cache it themselves.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
There's no need to BUG() if we enable ATS when it's already enabled. We
don't need to BUG() when disabling ATS on a device that doesn't support ATS
or if it's already disabled. If ATS is enabled, certainly we found an ATS
capability in the past, so it should still be there now.
Clean up these error paths.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Use the pci_physfn() helper rather than looking up physfn by hand.
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
The ATS setup code in ats_alloc_one() is only used by pci_ats_init(), so
inline it there. No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
We previously returned -ENODEV for devices that don't support ATS (except
that we always returned 0 for VFs, whether or not they support ATS).
For consistency, always return -EINVAL (not -ENODEV) if the device doesn't
support ATS. Return zero for VFs that support ATS.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
The pci_ats struct is small and will get smaller, so I don't think it's
worth allocating it separately from the pci_dev struct.
Embed the ATS fields directly into struct pci_dev.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Previously, we allocated pci_ats structures when an IOMMU driver called
pci_enable_ats(). An SR-IOV VF shares the STU setting with its PF, so when
enabling ATS on the VF, we allocated a pci_ats struct for the PF if it
didn't already have one. We held the sriov->lock to serialize threads
concurrently enabling ATS on several VFS so only one would allocate the PF
pci_ats.
Gregor reported a deadlock here:
pci_enable_sriov
sriov_enable
virtfn_add
mutex_lock(dev->sriov->lock) # acquire sriov->lock
pci_device_add
device_add
BUS_NOTIFY_ADD_DEVICE notifier chain
iommu_bus_notifier
amd_iommu_add_device # iommu_ops.add_device
init_iommu_group
iommu_group_get_for_dev
iommu_group_add_device
__iommu_attach_device
amd_iommu_attach_device # iommu_ops.attach_device
attach_device
pci_enable_ats
mutex_lock(dev->sriov->lock) # deadlock
There's no reason to delay allocating the pci_ats struct, and if we
allocate it for each device at enumeration-time, there's no need for
locking in pci_enable_ats().
Allocate pci_ats struct during enumeration, when we initialize other
capabilities.
Note that this implementation requires ATS to be enabled on the PF first,
before on any of the VFs because the PF controls the STU for all the VFs.
Link: http://permalink.gmane.org/gmane.linux.kernel.iommu/9433
Reported-by: Gregor Dick <gdick@solarflare.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
The PERST# line in am57x-evm is connected to a GPIO line and PERST# should
be driven high to indicate the clocks are stable (As per Figure 2-10: Power
Up of the PCIe CEM spec 3.0).
Add support to make GPIO drive PERST# line.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
DRA7xx requires the MSE bit to be cleared to set the master in standby
mode. (In DRA7xx TRM_vE, section 24.9.4.5.2.2.1 PCIe Controller Master
Standby Behavior advises to use the clearing of the local MSE bit to set
the master in standby. Without this some of the clocks do not idle).
Clear the MSE bit on suspend and enable it on resume. Clearing MSE bit is
required to get clocks to be idled after suspend.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jingoohan1@gmail.com>
Add PM support to pci-dra7xx so PCI clocks can be disabled during suspend
and enabled during resume without affecting PCI functionality.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jingoohan1@gmail.com>
Fix the error handling when pm_runtime_get_sync() fails.
If pm_runtime_get_sync() fails, call pm_runtime_disable() so there are no
unbalanced pm_runtime_enable() calls.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jingoohan1@gmail.com>
Change CONFIG_PCIE_IPROC_BCMA to tristate to make it possible to build this
driver as a module.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ray Jui <rjui@broadcom.com>
The Intel 100-series chipset now includes the integrated Ethernet as part
of a multifunction package. The Ethernet function does not include native
ACS support, but Intel confirms that the device is not capable of peer-to-
peer within the package. We can therefore quirk it to expose the
isolation.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: John Ronciak <john.ronciak@gmail.com>
set_irq_flags is ARM-specific with custom flags which have genirq
equivalents. Convert drivers to use the genirq interfaces directly, so we
can kill off set_irq_flags. The translation of flags is as follows:
IRQF_VALID -> !IRQ_NOREQUEST
IRQF_PROBE -> !IRQ_NOPROBE
IRQF_NOAUTOEN -> IRQ_NOAUTOEN
For IRQs managed by an irqdomain, the irqdomain core code handles clearing
and setting IRQ_NOREQUEST already, so there is no need to do this in .map()
functions, and we can simply remove the set_irq_flags calls. Some users
also modify IRQ_NOPROBE, and this has been maintained although it is not
clear that is really needed. There appears to be a great deal of blind
copy and paste of this code.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
CC: Kishon Vijay Abraham I <kishon@ti.com>
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Alexandre Courbot <gnurou@gmail.com>
CC: Jingoo Han <jingoohan1@gmail.com>
CC: Pratyush Anand <pratyush.anand@gmail.com>
CC: Simon Horman <horms@verge.net.au>
CC: Michal Simek <michal.simek@xilinx.com>
CC: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Quoting Arnd:
I was thinking the opposite approach and basically removing all uses
of IORESOURCE_CACHEABLE from the kernel. There are only a handful of
them.and we can probably replace them all with hardcoded
ioremap_cached() calls in the cases they are actually useful.
All existing usages of IORESOURCE_CACHEABLE call ioremap() instead of
ioremap_nocache() if the resource is cacheable, however ioremap() is
uncached by default. Clearly none of the existing usages care about the
cacheability. Particularly devm_ioremap_resource() never worked as
advertised since it always fell back to plain ioremap().
Clean this up as the new direction we want is to convert
ioremap_<type>() usages to memremap(..., flags).
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We queued interrupt events for the MRL being opened or closed, but the code
in interrupt_event_handler() that handles these events ignored them.
Stop enabling MRL interrupts and remove the ignored events.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The list of interrupt events (INT_BUTTON_IGNORE, INT_PRESENCE_ON, etc.) was
copied from other hotplug drivers, but pciehp doesn't use them all.
Remove the interrupt events that aren't used by pciehp.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
It's platform-dependent, but an MMIO read to a non-existent PCI device
generally returns data with all bits set. This happens when the host
bridge or Root Complex times out waiting for a response from the device and
fabricates return data to complete the CPU's read.
One example, reported in the bugzilla below, involved this hierarchy:
pci 0000:00:1c.0: PCI bridge to [bus 02-3a] Root Port
pci 0000:02:00.0: PCI bridge to [bus 03-0a] Upstream Port
pci 0000:03:03.0: PCI bridge to [bus 05-07] Downstream Port
pci 0000:05:00.0: PCI bridge to [bus 06-07] Thunderbolt Upstream Port
pci 0000:06:00.0: PCI bridge to [bus 07] Thunderbolt Downstream Port
pci 0000:07:00.0: BCM57762 NIC
Unplugging the Thunderbolt switch and the NIC below it resulted in this:
pciehp 0000:03:03.0: Surprise Removal
tg3 0000:07:00.0: tg3_abort_hw timed out, TX_MODE_ENABLE will not clear MAC_TX_MODE=ffffffff
pciehp 0000:06:00.0: unloading service driver pciehp
pciehp 0000:06:00.0: pcie_isr: intr_loc 11f
pciehp 0000:06:00.0: Switch interrupt received
pciehp 0000:06:00.0: Latch open on Slot
pciehp 0000:06:00.0: Attention button interrupt received
pciehp 0000:06:00.0: Button pressed on Slot
pciehp 0000:06:00.0: Presence/Notify input change
pciehp 0000:06:00.0: Card present on Slot
pciehp 0000:06:00.0: Power fault interrupt received
pciehp 0000:06:00.0: Data Link Layer State change
pciehp 0000:06:00.0: Link Up event
The pciehp driver correctly noticed that the Thunderbolt switch (05:00.0
and 06:00.0) and NIC (07:00.0) had been removed, and it called their driver
remove methods.
Since the NIC was already gone, tg3 received 0xffffffff when it tried to
read from the device. The resulting timeout is a tg3 issue and not of
interest here.
Similarly, since the 06:00.0 Thunderbolt switch was already gone,
pcie_isr() received 0xffff when it tried to read PCI_EXP_SLTSTA, and pciehp
thought that was valid status showing that many events had happened: the
latch had been opened, the attention button had been pressed, a card was
now present, and the link was now up. These are all wrong, of course, but
pciehp went on to try to power up and enumerate devices below the
non-existent bridge:
pciehp 0000:06:00.0: PCI slot - powering on due to button press
pciehp 0000:06:00.0: Surprise Insertion
pci 0000:07:00.0 id reading try 50 times with interval 20 ms to get ffffffff
[bhelgaas: changelog, also check in pcie_poll_cmd() & pcie_do_write_cmd()]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=99841
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI capabilities list for Intel DH895xCC VFs (device id 0x0443) with
QuickAssist Technology is prematurely terminated in hardware.
Workaround the issue by hard-coding the known expected next capability
pointer and saving the PCIE cap into internal buffer.
Patch generated against cryptodev-2.6
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* pci/irq:
PCI/MSI: Free legacy IRQ when enabling MSI/MSI-X
PCI: Add helpers to manage pci_dev->irq and pci_dev->irq_managed
PCI, x86: Implement pcibios_alloc_irq() and pcibios_free_irq()
PCI: Add pcibios_alloc_irq() and pcibios_free_irq()
* pci/misc:
PCI: Remove unused "pci_probe" flags
PCI: Add VPD function 0 quirk for Intel Ethernet devices
PCI: Add dev_flags bit to access VPD through function 0
PCI / ACPI: Fix pci_acpi_optimize_delay() comment
PCI: Remove a broken link in quirks.c
PCI: Remove useless redundant code
PCI: Simplify pci_find_(ext_)capability() return value checks
PCI: Move PCI_FIND_CAP_TTL to pci.h and use it in quirks
PCI: Add pcie_downstream_port() (true for Root and Switch Downstream Ports)
PCI: Fix pcie_port_device_resume() comment
PCI: Shift PCI_CLASS_NOT_DEFINED consistently with other classes
PCI: Revert aeb30016fe ("PCI: add Intel USB specific reset method")
PCI: Fix TI816X class code quirk
PCI: Fix generic NCR 53c810 class code quirk
PCI: Use PCI_CLASS_SERIAL_USB instead of bare number
PCI: Add quirk for Intersil/Techwell TW686[4589] AV capture cards
PCI: Remove Intel Cherrytrail D3 delays
* pci/resource:
PCI: Call pci_read_bridge_bases() from core instead of arch code
* pci/virtualization:
PCI: Restore ACS configuration as part of pci_restore_state()
* pci/host-designware:
PCI: designware: Don't complain missing *config* reg space if va_cfg0 is set
* pci/host-xgene:
PCI: xgene: Add support for a 64-bit prefetchable memory window
arm64: dts: Add APM X-Gene PCIe 64-bit prefetchable window
PCI: xgene: Drop owner assignment from platform_driver
* pci/host-xilinx:
PCI: xilinx: Check for MSI interrupt flag before handling as INTx
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Duc Dang <dhdang@apm.com>
Previously, pci_setup_device() and similar functions searched the
pci_bus->slots list without any locking. It was possible for another
thread to update the list while we searched it.
Add pci_dev_assign_slot() to search the list while holding pci_slot_mutex.
[bhelgaas: changelog, fold in CONFIG_SYSFS fix]
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rajat Jain reported a deadlock when PCIe hot-add and AER recovery happen at
the same time:
thread 1:
pciehp_enable_slot
pciehp_configure_device
pci_bus_add_devices
pci_bus_add_device
device_attach
device_lock(dev) # acquire device lock
...
pciehp_probe
init_slot
pci_hp_register
pci_create_slot
down_write(pci_bus_sem) # deadlock here
thread 2:
aer_isr_one_error
aer_process_err_device
do_recovery
broadcast_error_message(..., report_error_detected)
pci_walk_bus(..., cb=report_error_detected, ...)
down_read(&pci_bus_sem) # acquire pci_bus_sem
report_error_detected(dev) # cb()
device_lock(dev) # deadlock here
Previously, the bus->devices and bus->slots list were protected by
pci_bus_sem. In pci_create_slot(), we held it for writing so we could
add to the bus->slots list.
Add a new local pci_slot_mutex to protect bus->slots. Hold pci_bus_sem for
reading while searching the bus->devices list.
[bhelgaas: changelog]
Link: http://lkml.kernel.org/r/CAA93t1qpPqbih+UB0McA_d_+2rVaNkXsinAUxYzK9+JXSS+L-g@mail.gmail.com
Reported-by: Rajat Jain <rajatja@google.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Once MSI/MSI-X is enabled by the device driver, a PCI device won't use
legacy IRQs again until MSI/MSI-X is disabled.
Call pcibios_free_irq() when enabling MSI/MSI-X and pcibios_alloc_irq()
when disabling MSI/MSI-X. This allows arch code to manage resources
associated with the legacy IRQ.
[bhelgaas: changelog]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Add pcibios_alloc_irq() and pcibios_free_irq(), which are called when
binding/unbinding PCI device drivers.
PCI arch code may implement these to manage IRQ resources for hotplugged
devices.
[bhelgaas: changelog]
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
The only three users of that field are not using the msi_controller
structure anymore, so drop it altogether.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Ma Jun <majun258@huawei.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Duc Dang <dhdang@apm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1438091186-10244-20-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The X-Gene MSI driver only uses the msi_controller structure as
a way to match the host bridge with its MSI HW, and thus the
msi_domain.
But now that we can directly associate an msi_domain with a device,
there is no use keeping this msi_controller around.
Just remove all traces of msi_controller from the driver.
Tested-by: Duc Dang <dhdang@apm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Ma Jun <majun258@huawei.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1438091186-10244-19-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Now that we can easily find which MSI domain a PCI device is
using, use dev_get_msi_domain as a way to retrieve the information.
The original code is still used as a fallback.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Ma Jun <majun258@huawei.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Duc Dang <dhdang@apm.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1438091186-10244-8-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
A number of platforms do not need to use the msi-parent property,
as the host bridge itself provides the MSI controller.
Allow this configuration by performing an irq domain lookup based
on the host bridge node if it doesn't have a valid msi-parent property.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Ma Jun <majun258@huawei.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Duc Dang <dhdang@apm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1438091186-10244-7-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In order to populate the PCI host bridge msi_domain, use the
"msi-parent" attribute to lookup a corresponding irq domain.
If found, this is our MSI domain.
This gets plugged into the core PCI code.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Ma Jun <majun258@huawei.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Duc Dang <dhdang@apm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1438091186-10244-6-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In order to be able to populate the device msi_domain field,
add the necessary hooks to propagate the host bridge msi_domain
across secondary busses to devices.
So far, nobody populates the initial msi_domain.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Ma Jun <majun258@huawei.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Duc Dang <dhdang@apm.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1438091186-10244-5-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When creating a PCI/MSI domain, tag it with DOMAIN_BUS_PCI_MSI so
that it can be looked-up using irq_find_matching_host().
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: Yijing Wang <wangyijing@huawei.com>
Cc: Ma Jun <majun258@huawei.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Duc Dang <dhdang@apm.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1438091186-10244-3-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The current iProc BCMA front-end driver can only work on ARM32 based
platforms; therefore its config option in Kconfig should be changed to
reflect that. This fixes arm64 allmodconfig build failure when compiling
the the iProc BCMA driver that contains struct pci_sys_data that is
arm32 specific
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
PCI: iproc: Add arm64 support
Add arm64 support to the iProc PCIe driver.
Note that on arm32, bus->sysdata points to the arm32-specific
pci_sys_data struct, and pci_sys_data.private_data contains the
iproc_pcie pointer. For arm64, there's nothing corresponding to
pci_sys_data, so we keep the iproc_pcie pointer directly in
bus->sysdata.
In addition, arm64 does IRQ mapping in pcibios_add_device(), so it
doesn't need pci_fixup_irqs() as arm32 does.
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
When we scan a PCI bus, we read PCI-PCI bridge window registers with
pci_read_bridge_bases() so we can validate the resource hierarchy. Most
architectures call pci_read_bridge_bases() from pcibios_fixup_bus(), but
PCI-PCI bridges are not arch-specific, so this doesn't need to be in
arch-specific code.
Call pci_read_bridge_bases() directly from the PCI core instead of from
arch code.
For alpha and mips, we now call pci_read_bridge_bases() always; previously
we only called it if PCI_PROBE_ONLY was set.
[bhelgaas: changelog]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: James E.J. Bottomley <jejb@parisc-linux.org>
CC: Michael Ellerman <mpe@ellerman.id.au>
CC: Bjorn Helgaas <bhelgaas@google.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: David Howells <dhowells@redhat.com>
CC: Russell King <linux@arm.linux.org.uk>
CC: Tony Luck <tony.luck@intel.com>
CC: David S. Miller <davem@davemloft.net>
CC: Ingo Molnar <mingo@redhat.com>
CC: Guenter Roeck <linux@roeck-us.net>
CC: Michal Simek <monstr@monstr.eu>
CC: Chris Zankel <chris@zankel.net>
Currently on Keystone SoCs, we always complain:
keystone-pcie 21021000.pcie: missing *config* reg space
Keystone uses an older version of DesignWare hardware that doesn't have
ATU support. So va_cfg0_base and va_cfg1_base are already set up in
ks_dw_pcie_host_init() before calling dw_pcie_host_init(), and they point
to the remote config space address va (both same for Keystone). Add a
check to avoid this boot noise on Keystone.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add arm64 support to the iProc PCIe driver.
Note that on arm32, bus->sysdata points to the arm32-specific pci_sys_data
struct, and pci_sys_data.private_data contains the iproc_pcie pointer.
For arm64, there's nothing corresponding to pci_sys_data, so we keep the
iproc_pcie pointer directly in bus->sysdata.
In addition, arm64 does IRQ mapping in pcibios_add_device(), so it doesn't
need pci_fixup_irqs() as arm32 does.
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Move alloc_msi_entry() from PCI MSI code into generic MSI code, so it
can be reused by other generic MSI drivers. Also introduce
free_msi_entry() for completeness.
Suggested-by: Stuart Yoder <stuart.yoder@freescale.com>.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Yijing Wang <wangyijing@huawei.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Alexander Gordeev <agordeev@redhat.com>
Link: http://lkml.kernel.org/r/1436428847-8886-13-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Store 'struct device *' instead of 'struct pci_dev *' in struct msi_desc,
so struct msi_desc can be reused by non PCI based MSI drivers.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Reviewed-by: Yijing Wang <wangyijing@huawei.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Stuart Yoder <stuart.yoder@freescale.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Alexander Gordeev <agordeev@redhat.com>
Link: http://lkml.kernel.org/r/1436428847-8886-11-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move msi_list from struct pci_dev into struct device, so we can
support non-PCI-device based generic MSI interrupts.
msi_list is now conditional under CONFIG_GENERIC_MSI_IRQ, which is
selected from CONFIG_PCI_MSI, so no functional change for PCI MSI
users.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Reviewed-by: Yijing Wang <wangyijing@huawei.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Stuart Yoder <stuart.yoder@freescale.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Joe Perches <joe@perches.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Alexander Gordeev <agordeev@redhat.com>
Link: http://lkml.kernel.org/r/1436428847-8886-10-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use accessor for_each_pci_msi_entry() to access MSI device list, so we
could easily move msi_list from struct pci_dev into struct device
later.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Reviewed-by: Yijing Wang <wangyijing@huawei.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: xen-devel@lists.xenproject.org
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Stuart Yoder <stuart.yoder@freescale.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Link: http://lkml.kernel.org/r/1436428847-8886-7-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add helper function msi_desc_to_pci_sysdata() to retrieve sysdata from
an MSI descriptor. To avoid pulling include/linux/pci.h into
include/linux/msi.h, msi_desc_to_pci_sysdata() is implemented as a normal
function instead of an inline function.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Reviewed-by: Yijing Wang <wangyijing@huawei.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Stuart Yoder <stuart.yoder@freescale.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Alexander Gordeev <agordeev@redhat.com>
Link: http://lkml.kernel.org/r/1436428847-8886-2-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Set the PCI_DEV_FLAGS_VPD_REF_F0 flag on all Intel Ethernet device
functions other than function 0, so that on multi-function devices, we will
always read VPD from function 0 instead of from the other functions.
[bhelgaas: changelog]
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
CC: stable@vger.kernel.org
Add a dev_flags bit, PCI_DEV_FLAGS_VPD_REF_F0, to access VPD through
function 0 to provide VPD access on other functions. This is for hardware
devices that provide copies of the same VPD capability registers in
multiple functions. Because the kernel expects that each function has its
own registers, both the locking and the state tracking are affected by VPD
accesses to different functions.
On such devices for example, if a VPD write is performed on function 0,
*any* later attempt to read VPD from any other function of that device will
hang. This has to do with how the kernel tracks the expected value of the
F bit per function.
Concurrent accesses to different functions of the same device can not only
hang but also corrupt both read and write VPD data.
When hangs occur, typically the error message:
vpd r/w failed. This is likely a firmware bug on this device.
will be seen.
Never set this bit on function 0 or there will be an infinite recursion.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
CC: stable@vger.kernel.org
Previously we did not restore ACS state after a PCIe reset. This meant
that we could not reassign interfaces after a system suspend because the
D0->D3 transition disabled ACS, and we didn't restore it when going back to
D0.
Restore ACS configuration in pci_restore_state().
[bhelgaas: changelog]
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Allen Kay <allen.m.kay@intel.com>
CC: Chris Wright <chris@sous-sol.org>
CC: Alex Williamson <alex.williamson@redhat.com>
Occasionally both MSI and INTx bits in the interrupt decode register are
set at once by the Xilinx AXI PCIe Bridge, so the MSI flag in the interrupt
message should be checked to ensure that the correct handler is used.
If this check is not in place and the interrupt message type is MSI, the
INTx handler will be used erroneously when both type bits are set. This
will also be followed by a second read of the message FIFO, which can
result in the function returning early and the interrupt decode register
not being cleared if the FIFO is now empty.
Signed-off-by: Russell Joyce <russell.joyce@york.ac.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Use irq_data_get_msi_desc() to avoid redundant lookup of irq_data while we
already have a pointer to corresponding irq_data.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: linux-pci@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use irq_data access helper to access irq_data->msi_desc, so we can
move msi_desc from struct irq_data into struct irq_common_data later.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Rename irq_data_get_msi() as irq_data_get_msi_desc() to keep consistency
with other irq_data access helpers.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move first slot status read into while to simplify code.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Now in pci_hotplug_core.c, we randomly name a struct hotplug_slot and a
struct pci_slot. It's easy to confuse them, so let us use "slot" for a
struct hotplug_slot and "pci_slot" for a struct pci_slot.
No functional change.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The function takes ACPI handle, not the device itself. Fix the
comment
Signed-off-by: Srinidhi Kasagar <srinidhi.kasagar@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The return value of the pci_find_(ext_)capability() is either zero or the
position of a capability. It is never negative.
This patch consolidates the form of check from (pos <= 0) to (!pos).
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some quirks search for a HyperTransport capability and use a hard-coded TTL
value of 48 to avoid an infinite loop.
Move the definition of PCI_FIND_CAP_TTL to pci.h and use it instead of the
hard-coded TTL values.
[bhelgaas: changelog]
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
platform_driver_register() automatically supplies THIS_MODULE, so we don't
need to set it in the platform_driver struct.
Remove the xgene_msi_driver.owner assignment.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
As used in the PCIe spec, "Downstream Port" includes both Root Ports and
Switch Downstream Ports. We sometimes checked for PCI_EXP_TYPE_DOWNSTREAM
when we should have checked for PCI_EXP_TYPE_ROOT_PORT or
PCI_EXP_TYPE_DOWNSTREAM.
For a Root Port without a slot, the effect of this was that using
pcie_capability_read_word() to read PCI_EXP_SLTSTA returned zero instead of
showing the Presence Detect State bit hardwired to one as the PCIe Spec,
r3.0, sec 7.8, requires. (This read is completed in software because
previous PCIe spec versions didn't require PCI_EXP_SLTSTA to exist at all.)
Nothing in the kernel currently depends on this (pciehp only reads
PCI_EXP_SLTSTA on ports with slots), so this is a cleanup and not a
functional change.
Add a pcie_downstream_port() helper function and use it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The functions phy_exit() and phy_power_off() test whether their argument is
NULL and then return immediately. Thus the test around the calls is not
needed.
This issue was detected by using the Coccinelle software.
[bhelgaas: also phy_init() and phy_power_on(), as Ray Jui suggested]
[bhelgaas: also remove tests in iproc_pcie_remove()]
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
The function comment claimed this was pcie_port_device_suspend(), but it's
really pcie_port_device_resume(). Perils of cut and paste.
Use the correct function name in the comment.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The PCI class in dev->class is a three-byte value comprising a base class,
sub-class, and interface type. PCI_CLASS_NOT_DEFINED includes the base
class and sub-class, but not the interface type, so it should be shifted to
make space for the interface. It happens that PCI_CLASS_NOT_DEFINED is
zero, so it doesn't matter in the end, but we should still use it
consistently with other class definitions.
Treat PCI_CLASS_NOT_DEFINED as a base class/sub-class value that should
appear in bits 8-23 of dev->class.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Revert aeb30016fe ("PCI: add Intel USB specific reset method").
We checked for "dev->class == PCI_CLASS_SERIAL_USB", but dev->class
contains the entire three-byte base class/sub-class/interface, while
PCI_CLASS_SERIAL_USB is only the two-byte base class/sub-class.
This error meant that we used the Intel device-specific reset on devices
with class code 0x000c03 instead of those with class code 0x0c03xx.
0x000c03 is a reserved value in the 0x00 backwards compatibility base
class and shouldn't match any devices, so I think reset_intel_generic_dev()
always failed.
I considered adding a shift, but I can't test it, so it's as likely to
break something as to fix something.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Yu Zhao <yu.zhao@intel.com>
CC: Mathias Nyman <mathias.nyman@intel.com>
In fixup_ti816x_class(), we assigned "class = PCI_CLASS_MULTIMEDIA_VIDEO".
But PCI_CLASS_MULTIMEDIA_VIDEO is only the two-byte base class/sub-class
and needs to be shifted to make space for the low-order interface byte.
Shift PCI_CLASS_MULTIMEDIA_VIDEO to set the correct class code.
Fixes: 63c4408074 ("PCI: Add quirk for setting valid class for TI816X Endpoint")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Hemant Pedanekar <hemantp@ti.com>
In the generic quirk fixup_rev1_53c810(), added by a5312e28c1 ("[PATCH]
PCI: NCR 53c810 quirk"), we assigned "class = PCI_CLASS_STORAGE_SCSI". But
PCI_CLASS_STORAGE_SCSI is only the two-byte base class/sub-class and needs
to be shifted to make space for the low-order interface byte.
Furthermore, we had a similar quirk, pci_fixup_ncr53c810(), for arch/x86,
which assigned class correctly. The arch code is linked before the PCI
core, so arch quirks run before generic quirks. Therefore, on x86, the x86
arch quirk ran first, and the generic quirk did nothing because it saw that
dev->class was already set. But on other arches, the generic quirk set the
wrong class code.
Fix the generic quirk to set the correct class code and remove the
now-unnecessary x86-specific quirk.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Matthew Wilcox <matthew@wil.cx>
be6646bfba ("PCI: Prevent xHCI driver from claiming AMD Nolan USB3 DRD
device") added a quirk to override the PCI class code of the AMD Nolan
device.
Use PCI_CLASS_SERIAL_USB instead of a bare number to improve greppability.
Also add a log message about what we're doing.
No functional change except the new message.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Huang Rui <ray.huang@amd.com>
CC: Jason Chang <jason.chang@amd.com>
CC: Felipe Balbi <balbi@ti.com>
Intersil/Techwell TW686[4589]-based video capture cards have an empty
(zero) class code. Fix it.
Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Just like Haswell, Intel Atom Cherrytrail does not need the default 10ms
d3_delay imposed by the PCI specification.
Expand quirk_remove_d3_delay() to apply to Cherrytrail devices, so we can
ignore the 10ms delay before entering or exiting D3 suspend.
[bhelgaas: changelog, comment]
Signed-off-by: Srinidhi Kasagar <srinidhi.kasagar@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull irq fixes from Thomas Gleixner:
"This contains:
- a series of fixes for interrupt drivers to prevent a potential race
when installing a chained interrupt handler
- a fix for cpumask pointer misuse
- a fix for using the wrong interrupt number from struct irq_data
- removal of unused code and outdated comments
- a few new helper functions which allow us to cleanup the interrupt
handling code further in 4.3
I decided against doing the cleanup at the end of this merge window
and rather do the preparatory steps for 4.3, so we can run the final
ABI change at the end of the 4.3 merge window with less risk"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (26 commits)
ARM/LPC32xx: Use irq not hwirq for __irq_set_handler_locked()
genirq: Implement irq_set_handler_locked()/irq_set_chip_handler_name_locked()
genirq: Introduce helper irq_desc_get_irq()
genirq: Remove irq_node()
genirq: Clean up outdated comments related to include/linux/irqdesc.h
mn10300: Fix incorrect use of irq_data->affinity
MIPS/ralink: Fix race in installing chained IRQ handler
MIPS/pci: Fix race in installing chained IRQ handler
MIPS/ath25: Fix race in installing chained IRQ handler
MIPS/ath25: Fix race in installing chained IRQ handler
m68k/psc: Fix race in installing chained IRQ handler
avr32/at32ap: Fix race in installing chained IRQ handler
sh/intc: Fix race in installing chained IRQ handler
sh/intc: Fix potential race in installing chained IRQ handler
pinctrl/sun4i: Fix race in installing chained IRQ handler
pinctrl/samsung: Fix race in installing chained IRQ handler
pinctrl/samsung: Fix race in installing chained IRQ handler
pinctrl/exynos: Fix race in installing chained IRQ handler
pinctrl/st: Fix race in installing chained IRQ handler
pinctrl/adi2: Fix race in installing chained IRQ handler
...
- Add "make xenconfig" to assist in generating configs for Xen guests.
- Preparatory cleanups necessary for supporting 64 KiB pages in ARM
guests.
- Automatically use hvc0 as the default console in ARM guests.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJVkpoqAAoJEFxbo/MsZsTRu3IH/2AMPx2i65hoSqfHtGf3sz/z
XNfcidVmOElFVXGaW83m0tBWMemT5LpOGRfiq5sIo8xt/8xD2vozEkl/3kkf3RrX
EmZDw3E8vmstBdBTjWdovVhNenRc0m0pB5daS7wUdo9cETq1ag1L3BHTB3fEBApO
74V6qAfnhnq+snqWhRD3XAk3LKI0nWuWaV+5HsmxDtnunGhuRLGVs7mwxZGg56sM
mILA0eApGPdwyVVpuDe0SwV52V8E/iuVOWTcomGEN2+cRWffG5+QpHxQA8bOtF6O
KfqldiNXOY/idM+5+oSm9hespmdWbyzsFqmTYz0LvQvxE8eEZtHHB3gIcHkE8QU=
=danz
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.2-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from David Vrabel:
"Xen features and cleanups for 4.2-rc0:
- add "make xenconfig" to assist in generating configs for Xen guests
- preparatory cleanups necessary for supporting 64 KiB pages in ARM
guests
- automatically use hvc0 as the default console in ARM guests"
* tag 'for-linus-4.2-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
block/xen-blkback: s/nr_pages/nr_segs/
block/xen-blkfront: Remove invalid comment
block/xen-blkfront: Remove unused macro MAXIMUM_OUTSTANDING_BLOCK_REQS
arm/xen: Drop duplicate define mfn_to_virt
xen/grant-table: Remove unused macro SPP
xen/xenbus: client: Fix call of virt_to_mfn in xenbus_grant_ring
xen: Include xen/page.h rather than asm/xen/page.h
kconfig: add xenconfig defconfig helper
kconfig: clarify kvmconfig is for kvm
xen/pcifront: Remove usage of struct timeval
xen/tmem: use BUILD_BUG_ON() in favor of BUG_ON()
hvc_xen: avoid uninitialized variable warning
xenbus: avoid uninitialized variable warning
xen/arm: allow console=hvc0 to be omitted for guests
arm,arm64/xen: move Xen initialization earlier
arm/xen: Correctly check if the event channel interrupt is present
Mohit's email-id doesn't exist anymore as he has left the company.
Replace ST's id with mohit.kumar.dhaka@gmail.com.
Signed-off-by: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Mohit Kumar <mohit.kumar.dhaka@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pratyush.anand@st.com email-id doesn't exist anymore as I have left the
company. Replace ST's id with pratyush.anand@gmail.com.
Signed-off-by: Pratyush Anand <pratyush.anand@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a race where a pending interrupt could be received and the handler
called before the handler's data has been setup, by converting to
irq_set_chained_handler_and_data().
Search and conversion was done with coccinelle:
@@
expression E1, E2, E3;
@@
(
-if (irq_set_chained_handler(E1, E3) != 0)
- BUG();
|
-irq_set_chained_handler(E1, E3);
)
-irq_set_handler_data(E1, E2);
+irq_set_chained_handler_and_data(E1, E3, E2);
@@
expression E1, E2, E3;
@@
(
-if (irq_set_chained_handler(E1, E3) != 0)
- BUG();
...
|
-irq_set_chained_handler(E1, E3);
...
)
-irq_set_handler_data(E1, E2);
+irq_set_chained_handler_and_data(E1, E3, E2);
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
- ACPICA update to upstream revision 20150515 including basic
support for ACPI 6 features: new ACPI tables introduced by
ACPI 6 (STAO, XENV, WPBT, NFIT, IORT), changes related to the
other tables (DTRM, FADT, LPIT, MADT), new predefined names
(_BTH, _CR3, _DSD, _LPI, _MTL, _PRR, _RDI, _RST, _TFP, _TSN),
fixes and cleanups (Bob Moore, Lv Zheng).
- ACPI device power management core code update to follow ACPI 6
which reflects the ACPI device power management implementation
in Windows (Rafael J Wysocki).
- Rework of the backlight interface selection logic to reduce the
number of kernel command line options and improve the handling
of DMI quirks that may be involved in that and to make the
code generally more straightforward (Hans de Goede).
- Fixes for the ACPI Embedded Controller (EC) driver related to
the handling of EC transactions (Lv Zheng).
- Fix for a regression related to the ACPI resources management
and resulting from a recent change of ACPI initialization code
ordering (Rafael J Wysocki).
- Fix for a system initialization regression related to ACPI
introduced during the 3.14 cycle and caused by running the
code that switches the platform over to the ACPI mode too
early in the initialization sequence (Rafael J Wysocki).
- Support for the ACPI _CCA device configuration object related
to DMA cache coherence (Suravee Suthikulpanit).
- ACPI/APEI fixes and cleanups (Jiri Kosina, Borislav Petkov).
- ACPI battery driver cleanups (Luis Henriques, Mathias Krause).
- ACPI processor driver cleanups (Hanjun Guo).
- Cleanups and documentation update related to the ACPI device
properties interface based on _DSD (Rafael J Wysocki).
- ACPI device power management fixes (Rafael J Wysocki).
- Assorted cleanups related to ACPI (Dominik Brodowski. Fabian
Frederick, Lorenzo Pieralisi, Mathias Krause, Rafael J Wysocki).
- Fix for a long-standing issue causing General Protection Faults
to be generated occasionally on return to user space after resume
from ACPI-based suspend-to-RAM on 32-bit x86 (Ingo Molnar).
- Fix to make the suspend core code return -EBUSY consistently in
all cases when system suspend is aborted due to wakeup detection
(Ruchi Kandoi).
- Support for automated device wakeup IRQ handling allowing drivers
to make their PM support more starightforward (Tony Lindgren).
- New tracepoints for suspend-to-idle tracing and rework of the
prepare/complete callbacks tracing in the PM core (Todd E Brandt,
Rafael J Wysocki).
- Wakeup sources framework enhancements (Jin Qian).
- New macro for noirq system PM callbacks (Grygorii Strashko).
- Assorted cleanups related to system suspend (Rafael J Wysocki).
- cpuidle core cleanups to make the code more efficient (Rafael J
Wysocki).
- powernv/pseries cpuidle driver update (Shilpasri G Bhat).
- cpufreq core fixes related to CPU online/offline that should
reduce the overhead of these operations quite a bit, unless the
CPU in question is physically going away (Viresh Kumar, Saravana
Kannan).
- Serialization of cpufreq governor callbacks to avoid race
conditions in some cases (Viresh Kumar).
- intel_pstate driver fixes and cleanups (Doug Smythies, Prarit
Bhargava, Joe Konno).
- cpufreq driver (arm_big_little, cpufreq-dt, qoriq) updates (Sudeep
Holla, Felipe Balbi, Tang Yuantian).
- Assorted cleanups in cpufreq drivers and core (Shailendra Verma,
Fabian Frederick, Wang Long).
- New Device Tree bindings for representing Operating Performance
Points (Viresh Kumar).
- Updates for the common clock operations support code in the PM
core (Rajendra Nayak, Geert Uytterhoeven).
- PM domains core code update (Geert Uytterhoeven).
- Intel Knights Landing support for the RAPL (Running Average Power
Limit) power capping driver (Dasaratharaman Chandramouli).
- Fixes related to the floor frequency setting on Atom SoCs in the
RAPL power capping driver (Ajay Thomas).
- Runtime PM framework documentation update (Ben Dooks).
- cpupower tool fix (Herton R Krzesinski).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=7jTj
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"The rework of backlight interface selection API from Hans de Goede
stands out from the number of commits and the number of affected
places perspective. The cpufreq core fixes from Viresh Kumar are
quite significant too as far as the number of commits goes and because
they should reduce CPU online/offline overhead quite a bit in the
majority of cases.
From the new featues point of view, the ACPICA update (to upstream
revision 20150515) adding support for new ACPI 6 material to ACPICA is
the one that matters the most as some new significant features will be
based on it going forward. Also included is an update of the ACPI
device power management core to follow ACPI 6 (which in turn reflects
the Windows' device PM implementation), a PM core extension to support
wakeup interrupts in a more generic way and support for the ACPI _CCA
device configuration object.
The rest is mostly fixes and cleanups all over and some documentation
updates, including new DT bindings for Operating Performance Points.
There is one fix for a regression introduced in the 4.1 cycle, but it
adds quite a number of lines of code, it wasn't really ready before
Thursday and you were on vacation, so I refrained from pushing it on
the last minute for 4.1.
Specifics:
- ACPICA update to upstream revision 20150515 including basic support
for ACPI 6 features: new ACPI tables introduced by ACPI 6 (STAO,
XENV, WPBT, NFIT, IORT), changes related to the other tables (DTRM,
FADT, LPIT, MADT), new predefined names (_BTH, _CR3, _DSD, _LPI,
_MTL, _PRR, _RDI, _RST, _TFP, _TSN), fixes and cleanups (Bob Moore,
Lv Zheng).
- ACPI device power management core code update to follow ACPI 6
which reflects the ACPI device power management implementation in
Windows (Rafael J Wysocki).
- rework of the backlight interface selection logic to reduce the
number of kernel command line options and improve the handling of
DMI quirks that may be involved in that and to make the code
generally more straightforward (Hans de Goede).
- fixes for the ACPI Embedded Controller (EC) driver related to the
handling of EC transactions (Lv Zheng).
- fix for a regression related to the ACPI resources management and
resulting from a recent change of ACPI initialization code ordering
(Rafael J Wysocki).
- fix for a system initialization regression related to ACPI
introduced during the 3.14 cycle and caused by running the code
that switches the platform over to the ACPI mode too early in the
initialization sequence (Rafael J Wysocki).
- support for the ACPI _CCA device configuration object related to
DMA cache coherence (Suravee Suthikulpanit).
- ACPI/APEI fixes and cleanups (Jiri Kosina, Borislav Petkov).
- ACPI battery driver cleanups (Luis Henriques, Mathias Krause).
- ACPI processor driver cleanups (Hanjun Guo).
- cleanups and documentation update related to the ACPI device
properties interface based on _DSD (Rafael J Wysocki).
- ACPI device power management fixes (Rafael J Wysocki).
- assorted cleanups related to ACPI (Dominik Brodowski, Fabian
Frederick, Lorenzo Pieralisi, Mathias Krause, Rafael J Wysocki).
- fix for a long-standing issue causing General Protection Faults to
be generated occasionally on return to user space after resume from
ACPI-based suspend-to-RAM on 32-bit x86 (Ingo Molnar).
- fix to make the suspend core code return -EBUSY consistently in all
cases when system suspend is aborted due to wakeup detection (Ruchi
Kandoi).
- support for automated device wakeup IRQ handling allowing drivers
to make their PM support more starightforward (Tony Lindgren).
- new tracepoints for suspend-to-idle tracing and rework of the
prepare/complete callbacks tracing in the PM core (Todd E Brandt,
Rafael J Wysocki).
- wakeup sources framework enhancements (Jin Qian).
- new macro for noirq system PM callbacks (Grygorii Strashko).
- assorted cleanups related to system suspend (Rafael J Wysocki).
- cpuidle core cleanups to make the code more efficient (Rafael J
Wysocki).
- powernv/pseries cpuidle driver update (Shilpasri G Bhat).
- cpufreq core fixes related to CPU online/offline that should reduce
the overhead of these operations quite a bit, unless the CPU in
question is physically going away (Viresh Kumar, Saravana Kannan).
- serialization of cpufreq governor callbacks to avoid race
conditions in some cases (Viresh Kumar).
- intel_pstate driver fixes and cleanups (Doug Smythies, Prarit
Bhargava, Joe Konno).
- cpufreq driver (arm_big_little, cpufreq-dt, qoriq) updates (Sudeep
Holla, Felipe Balbi, Tang Yuantian).
- assorted cleanups in cpufreq drivers and core (Shailendra Verma,
Fabian Frederick, Wang Long).
- new Device Tree bindings for representing Operating Performance
Points (Viresh Kumar).
- updates for the common clock operations support code in the PM core
(Rajendra Nayak, Geert Uytterhoeven).
- PM domains core code update (Geert Uytterhoeven).
- Intel Knights Landing support for the RAPL (Running Average Power
Limit) power capping driver (Dasaratharaman Chandramouli).
- fixes related to the floor frequency setting on Atom SoCs in the
RAPL power capping driver (Ajay Thomas).
- runtime PM framework documentation update (Ben Dooks).
- cpupower tool fix (Herton R Krzesinski)"
* tag 'pm+acpi-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (194 commits)
cpuidle: powernv/pseries: Auto-promotion of snooze to deeper idle state
x86: Load __USER_DS into DS/ES after resume
PM / OPP: Add binding for 'opp-suspend'
PM / OPP: Allow multiple OPP tables to be passed via DT
PM / OPP: Add new bindings to address shortcomings of existing bindings
ACPI: Constify ACPI device IDs in documentation
ACPI / enumeration: Document the rules regarding the PRP0001 device ID
ACPI / video: Make acpi_video_unregister_backlight() private
acpi-video-detect: Remove old API
toshiba-acpi: Port to new backlight interface selection API
thinkpad-acpi: Port to new backlight interface selection API
sony-laptop: Port to new backlight interface selection API
samsung-laptop: Port to new backlight interface selection API
msi-wmi: Port to new backlight interface selection API
msi-laptop: Port to new backlight interface selection API
intel-oaktrail: Port to new backlight interface selection API
ideapad-laptop: Port to new backlight interface selection API
fujitsu-laptop: Port to new backlight interface selection API
eeepc-laptop: Port to new backlight interface selection API
dell-wmi: Port to new backlight interface selection API
...
Pull x86 core updates from Ingo Molnar:
"There were so many changes in the x86/asm, x86/apic and x86/mm topics
in this cycle that the topical separation of -tip broke down somewhat -
so the result is a more traditional architecture pull request,
collected into the 'x86/core' topic.
The topics were still maintained separately as far as possible, so
bisectability and conceptual separation should still be pretty good -
but there were a handful of merge points to avoid excessive
dependencies (and conflicts) that would have been poorly tested in the
end.
The next cycle will hopefully be much more quiet (or at least will
have fewer dependencies).
The main changes in this cycle were:
* x86/apic changes, with related IRQ core changes: (Jiang Liu, Thomas
Gleixner)
- This is the second and most intrusive part of changes to the x86
interrupt handling - full conversion to hierarchical interrupt
domains:
[IOAPIC domain] -----
|
[MSI domain] --------[Remapping domain] ----- [ Vector domain ]
| (optional) |
[HPET MSI domain] ----- |
|
[DMAR domain] -----------------------------
|
[Legacy domain] -----------------------------
This now reflects the actual hardware and allowed us to distangle
the domain specific code from the underlying parent domain, which
can be optional in the case of interrupt remapping. It's a clear
separation of functionality and removes quite some duct tape
constructs which plugged the remap code between ioapic/msi/hpet
and the vector management.
- Intel IOMMU IRQ remapping enhancements, to allow direct interrupt
injection into guests (Feng Wu)
* x86/asm changes:
- Tons of cleanups and small speedups, micro-optimizations. This
is in preparation to move a good chunk of the low level entry
code from assembly to C code (Denys Vlasenko, Andy Lutomirski,
Brian Gerst)
- Moved all system entry related code to a new home under
arch/x86/entry/ (Ingo Molnar)
- Removal of the fragile and ugly CFI dwarf debuginfo annotations.
Conversion to C will reintroduce many of them - but meanwhile
they are only getting in the way, and the upstream kernel does
not rely on them (Ingo Molnar)
- NOP handling refinements. (Borislav Petkov)
* x86/mm changes:
- Big PAT and MTRR rework: making the code more robust and
preparing to phase out exposing direct MTRR interfaces to drivers -
in favor of using PAT driven interfaces (Toshi Kani, Luis R
Rodriguez, Borislav Petkov)
- New ioremap_wt()/set_memory_wt() interfaces to support
Write-Through cached memory mappings. This is especially
important for good performance on NVDIMM hardware (Toshi Kani)
* x86/ras changes:
- Add support for deferred errors on AMD (Aravind Gopalakrishnan)
This is an important RAS feature which adds hardware support for
poisoned data. That means roughly that the hardware marks data
which it has detected as corrupted but wasn't able to correct, as
poisoned data and raises an APIC interrupt to signal that in the
form of a deferred error. It is the OS's responsibility then to
take proper recovery action and thus prolonge system lifetime as
far as possible.
- Add support for Intel "Local MCE"s: upcoming CPUs will support
CPU-local MCE interrupts, as opposed to the traditional system-
wide broadcasted MCE interrupts (Ashok Raj)
- Misc cleanups (Borislav Petkov)
* x86/platform changes:
- Intel Atom SoC updates
... and lots of other cleanups, fixlets and other changes - see the
shortlog and the Git log for details"
* 'x86-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (222 commits)
x86/hpet: Use proper hpet device number for MSI allocation
x86/hpet: Check for irq==0 when allocating hpet MSI interrupts
x86/mm/pat, drivers/infiniband/ipath: Use arch_phys_wc_add() and require PAT disabled
x86/mm/pat, drivers/media/ivtv: Use arch_phys_wc_add() and require PAT disabled
x86/platform/intel/baytrail: Add comments about why we disabled HPET on Baytrail
genirq: Prevent crash in irq_move_irq()
genirq: Enhance irq_data_to_desc() to support hierarchy irqdomain
iommu, x86: Properly handle posted interrupts for IOMMU hotplug
iommu, x86: Provide irq_remapping_cap() interface
iommu, x86: Setup Posted-Interrupts capability for Intel iommu
iommu, x86: Add cap_pi_support() to detect VT-d PI capability
iommu, x86: Avoid migrating VT-d posted interrupts
iommu, x86: Save the mode (posted or remapped) of an IRTE
iommu, x86: Implement irq_set_vcpu_affinity for intel_ir_chip
iommu: dmar: Provide helper to copy shared irte fields
iommu: dmar: Extend struct irte for VT-d Posted-Interrupts
iommu: Add new member capability to struct irq_remap_ops
x86/asm/entry/64: Disentangle error_entry/exit gsbase/ebx/usermode code
x86/asm/entry/32: Shorten __audit_syscall_entry() args preparation
x86/asm/entry/32: Explain reloading of registers after __audit_syscall_entry()
...
* acpi-pm:
ACPI / PM: Add missing pm_generic_complete() invocation
ACPI / PM: Turn power resources on and off in the right order during resume
ACPI / PM: Rework device power management to follow ACPI 6
ACPI / PM: Drop stale comment from acpi_power_transition()
* acpi-apei:
GHES: Make NMI handler have a single reader
GHES: Elliminate double-loop in the NMI handler
GHES: Panic right after detection
GHES: Carve out the panic functionality
GHES: Carve out error queueing in a separate function
* acpi-osl:
ACPI / osl: use same type for acpi_predefined_names values as in definition
* acpi-pci:
ACPI / PCI: remove stale list_head in struct acpi_prt_entry
* pci/host-xgene:
PCI: xgene: Allow config access to Root Port even when link is down
PCI: xgene: Disable Configuration Request Retry Status for v1 silicon
* pci/hotplug:
PCI: pciehp: Inline the "handle event" functions into the ISR
PCI: pciehp: Rename queue_interrupt_event() to pciehp_queue_interrupt_event()
PCI: pciehp: Make queue_interrupt_event() void
PCI: pciehp: Clean up debug logging
The pciehp_handle_*() functions (pciehp_handle_attention_button(), etc.)
only contain a line or two of useful code, so it's clumsy to put
them in separate functions. All they so is add an event to a work queue,
and it's clearer to see that directly in the ISR.
Inline them directly into pcie_isr(). No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rajat Jain <rajatja@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Rename queue_interrupt_event() to pciehp_queue_interrupt_event() so we can
make it extern and call it from pcie_isr().
No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rajat Jain <rajatja@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Nobody looks at the return value from queue_interrupt_event(), so errors
were silently ignored. Convert it to a "void" function and note the error
in the dmesg log.
No functional change except the new message.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rajat Jain <rajatja@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Previously, when a Root Port's link was down, we didn't allow config access
to the Root Port, which meant that if the Root Port led to an empty slot,
"lspci" didn't even show the Root Port.
Allow config access to Root Port even when link is down.
[bhelgaas: changelog, fold in unused var fix]
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Tanmay Inamdar <tinamdar@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When a CPU reads the Vendor and Device ID of a non-existent device, the
controller should fabricate return data of 0xFFFFFFFF. Configuration
Request Retry Status (CRS) is not applicable in this case because the
device doesn't exist at all.
The X-Gene v1 PCIe controller has a bug in the CRS logic such that when CRS
is enabled, it fabricates return data of 0xFFFF0001 for this case, which
means "the device exists but is not ready." That causes the PCI core to
retry the read until it times out after 60 seconds.
Disable CRS capability advertisement by clearing the CRS Software
Visibility bit in the Root Capabilities Register.
[bhelgaas: changelog and comment]
Tested-by: Ian Campbell <ian.campbell@citrix.com>
Tested-by: Marcin Juszkiewicz <mjuszkiewicz@redhat.com>
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tanmay Inamdar <tinamdar@apm.com>
The pciehp debug logging is overly verbose and often redundant. Almost all
of the information printed by dbg_ctrl() is also printed by the normal PCI
core enumeration code and by pcie_init().
Remove the redundant debug info.
When claiming a pciehp bridge, we print the slot characteristics, e.g.,
Slot #6 AttnBtn- AttnInd- PwrInd- PwrCtrl- MRL- Interlock- NoCompl+ LLActRep+
Add the Hot-Plug Capable and Hot-Plug Surprise bits to this information,
and print it all in the same order as lspci does.
No functional change except the message text changes.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rajat Jain <rajatja@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Use "u32", not "uint32_t", for consistency. Use "tmp", not "temp", for
consistency within the driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Richard Zhu <Richard.Zhu@freescale.com>
No one uses pci_scan_bus_parented() any more, remove it.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Currently, the timeout is never detected as count has a value of -1 if a
timeout happens, but the code is checking for 0. Also, this patch removes
the unneeded final wait if a timeout occurs.
[bhelgaas: reworked starting from http://lkml.kernel.org/r/1433543864-7252-1-git-send-email-troy.kisky@boundarydevices.com]
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Update the Link Control Enable Clock Power Management bit the same
way we update the ASPM Control bits, with a single call of
pcie_capability_clear_and_set_word().
No functional change; this just makes both paths use the same style.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
All the DesignWare-based host drivers loop waiting for the link to come up,
but they do it several ways that are needlessly different.
Wait for the link to come up in a consistent style across all the
DesignWare drivers. No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
All other DesignWare-based drivers have a *_establish_link() function.
This functionality is trivial for Layerscape, but factor out a
ls_pcie_establish_link() for consistency with the other drivers. No
functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
All the other DesignWare-based drivers use dw_pcie_link_up(), so use it in
this driver, too, for consistency. No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
We already use dw_pcie_link_up() once in dra7xx_pcie_establish_link(), but
we duplicate its code later. Use dw_pcie_link_up() for consistency. No
functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
The commit referenced below deferred waiting for command completion until
the start of the next command, allowing hardware to do the latching
asynchronously. Unfortunately, being ready to accept a new command is the
only indication we have that the previous command is completed. In cases
where we need that state change to be enabled, we must still wait for
completion. For instance, pciehp_reset_slot() attempts to disable anything
that might generate a surprise hotplug on slots that support presence
detection. If we don't wait for those settings to latch before the
secondary bus reset, we negate any value in attempting to prevent the
spurious hotplug.
Create a base function with optional wait and helper functions so that
pcie_write_cmd() turns back into the "safe" interface which waits before
and after issuing a command and add pcie_write_cmd_nowait(), which
eliminates the trailing wait for asynchronous completion. The following
functions are returned to their previous behavior:
pciehp_power_on_slot
pciehp_power_off_slot
pcie_disable_notification
pciehp_reset_slot
The rationale is that pciehp_power_on_slot() enables the link and therefore
relies on completion of power-on. pciehp_power_off_slot() and
pcie_disable_notification() need a wait because data structures may be
freed after these calls and continued signaling from the device would be
unexpected. And, of course, pciehp_reset_slot() needs to wait for the
scenario outlined above.
Fixes: 3461a06866 ("PCI: pciehp: Wait for hotplug command completion lazily")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v3.17+
struct timeval uses a 32-bit field for representing seconds, which
will overflow in the year 2038 and beyond. Replace struct timeval with
64-bit ktime_t which is 2038 safe. This is part of a larger effort to
remove instances of 32-bit timekeeping variables (timeval, time_t and
timespec) from the kernel.
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
APM X-Gene v1 SoC supports its own implementation of MSI, which is not
compliant to GIC V2M specification for MSI Termination.
There is a single MSI block in X-Gene v1 SOC which serves all 5 PCIe ports.
This MSI block supports 2048 MSI termination ports coalesced into 16
physical HW IRQ lines and shared across all 5 PCIe ports.
As there are only 16 HW IRQs to serve 2048 MSI vectors, to support
set_affinity correctly for each MSI vectors, the 16 HW IRQs are statically
allocated to 8 X-Gene v1 cores (2 HW IRQs for each cores). To steer MSI
interrupt to target CPU, MSI vector is moved around these HW IRQs lines.
With this approach, the total MSI vectors this driver supports is reduced
to 256.
[bhelgaas: squash doc, driver, maintainer update]
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Tanmay Inamdar <tinamdar@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Rename imx6_pcie_start_link() to imx6_pcie_establish_link() to follow the
convention of other DesignWare-based host drivers. No functional change.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Pratyush Anand <pratyush.anand@gmail.com>
In d74b9027a4 ("PCI: Consider additional PF's IOV BAR alignment in sizing
and assigning"), we store additional alignment in realloc_head and take
this into consideration for assignment.
In __assign_resources_sorted(), we changed dev_res->res->start, then used
resource_start() (which depends on res->start), so the recomputed res->end
was completely bogus. Even if we'd had the correct size, the end would
have been off by one.
Preserve the resource size when we adjust its alignment.
[bhelgaas: changelog]
Fixes: d74b9027a4 ("PCI: Consider additional PF's IOV BAR alignment in sizing and assigning")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Wei Yang <weiyang@linux.vnet.ibm.com>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
David Ahern reported that d63e2e1f3d ("sparc/PCI: Clip bridge windows
to fit in upstream windows") fails to boot on sparc/T5-8:
pci 0000:06:00.0: reg 0x184: can't handle BAR above 4GB (bus address 0x110204000)
The problem is that sparc64 assumed that dma_addr_t only needed to hold DMA
addresses, i.e., bus addresses returned via the DMA API (dma_map_single(),
etc.), while the PCI core assumed dma_addr_t could hold *any* bus address,
including raw BAR values. On sparc64, all DMA addresses fit in 32 bits, so
dma_addr_t is a 32-bit type. However, BAR values can be 64 bits wide, so
they don't fit in a dma_addr_t. d63e2e1f3d added new checking that
tripped over this mismatch.
Add pci_bus_addr_t, which is wide enough to hold any PCI bus address,
including both raw BAR values and DMA addresses. This will be 64 bits
on 64-bit platforms and on platforms with a 64-bit dma_addr_t. Then
dma_addr_t only needs to be wide enough to hold addresses from the DMA API.
[bhelgaas: changelog, bugzilla, Kconfig to ensure pci_bus_addr_t is at
least as wide as dma_addr_t, documentation]
Fixes: d63e2e1f3d ("sparc/PCI: Clip bridge windows to fit in upstream windows")
Fixes: 23b13bc76f ("PCI: Fail safely if we can't handle BARs larger than 4GB")
Link: http://lkml.kernel.org/r/CAE9FiQU1gJY1LYrxs+ma5LCTEEe4xmtjRG0aXJ9K_Tsu+m9Wuw@mail.gmail.com
Link: http://lkml.kernel.org/r/1427857069-6789-1-git-send-email-yinghai@kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=96231
Reported-by: David Ahern <david.ahern@oracle.com>
Tested-by: David Ahern <david.ahern@oracle.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
CC: stable@vger.kernel.org # v3.19+
pci_ari_enabled() is useful outside of drivers/pci, particularly for
deriving INTx routing via ACPI _PRT, so move it to the global header.
Also convert to bool return.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Don Dutile <ddutile@redhat.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Previously we assumed that PCIe Root Ports and Downstream Ports had Links
on their secondary side. That is true in most systems, but it is possible
to connect a switch with either an Upstream or a Downstream Port leading
downstream.
Instead of relying on the component type to identify devices that have
links leading downstream, use the "dev->has_secondary_link" field.
[bhelgaas: changelog]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The resource list is only used in the setup process and was never freed.
pci_add_resource() allocates a memory area to store the list item.
Fix the memory leak.
Tested-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
The struct iproc_pcie.resources member was pointing to a stack variable and
is invalid after the registration function returned.
Remove this pointer and add a parameter to the function.
Tested-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
In d74b9027a4 ("PCI: Consider additional PF's IOV BAR alignment in sizing
and assigning"), it stores additional alignment in realloc_head and takes
this into consideration for assignment.
After getting the additional alignment, it reorders the head list so
resources with bigger alignment are ahead of resources with smaller
alignment. It does this by iterating over the head list and inserting
ahead of any resource with smaller alignment. This should be done for the
first occurrence, but the code currently iterates over the whole list.
Fix this by terminating the loop when we find the first smaller resource in
the head list.
[bhelgaas: changelog]
Fixes: d74b9027a4 ("PCI: Consider additional PF's IOV BAR alignment in sizing and assigning")
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
After b97ea289cf ("PCI: Assign resources before drivers claim devices
(pci_scan_root_bus())"), pci_scan_root_bus() no longer adds the devices, so
it is equivalent to:
pci_create_root_bus()
pci_scan_child_bus()
Use pci_scan_root_bus() to simplify the code.
[bhelgaas: changelog]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
CC: Mohit Kumar <mohit.kumar@st.com>
After b97ea289cf ("PCI: Assign resources before drivers claim devices
(pci_scan_root_bus())"), pci_scan_root_bus() no longer adds the devices, so
it is equivalent to tegra_pcie_scan_bus().
Remove tegra_pcie_scan_bus() (the hw.scan method), so we use the generic
pci_scan_root_bus() path.
[bhelgaas: changelog]
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thierry Reding <treding@nvidia.com>
After b97ea289cf ("PCI: Assign resources before drivers claim devices
(pci_scan_root_bus())"), pci_scan_root_bus() no longer adds the devices, so
it is equivalent to mvebu_pcie_scan_bus().
Remove mvebu_pcie_scan_bus() (the hw.scan method), so we use the generic
pci_scan_root_bus() path. We also need to use pci_common_init_dev()
instead of pci_common_init() so we can supply the host bridge device
pointer.
[bhelgaas: changelog]
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: Jason Cooper <jason@lakedaemon.net>
We allocate pcie_link_state for the component at the upstream end of a
Link. Previously we did this by allocating pcie_link_state for Root Ports
and Downstream Ports. This works fine for the typical topology:
00:1c.0 Root Port [bridge to bus 02]
02:00.0 Upstream Port [bridge to bus 03]
03:00.0 Downstream Port [bridge to bus 04]
04:00.0 Endpoint or Switch Port
However, it is possible to have a Root Port connected to a Downstream Port
instead of an Upstream Port, as in Robert White's ATCA system:
00:1c.0 Root Port [bridge to bus 02]
02:00.0 Downstream Port [bridge to bus 03]
03:01.0 Downstream Port [bridge to bus 04]
04:00.0 Endpoint or Switch Port
In this topology, we wrongly allocated pcie_link_state for the 02:00.0
Downstream Port, which is actually the *downstream* end of a link. This
led to the following NULL pointer dereference when we tried to connect this
link into the tree of links starting at the 00:1c.0 Root Port:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000088
IP: [<ffffffff81550324>] pcie_aspm_init_link_state+0x744/0x850
Hardware name: Kontron B3001/B3001, BIOS 4.6.3 08/07/2012
Call Trace:
[<ffffffff8153b865>] pci_scan_slot+0xd5/0x120
[<ffffffff8153ca1d>] pci_scan_child_bus+0x2d/0xd0
...
Instead of relying on the component type to identify the upstream end of a
link, use the "dev->has_secondary_link" field.
This means it's now possible for an Upstream Port to have a link on its
secondary side, so alloc_pcie_link_state() needs to connect links
originating from both Upstream and Downstream Ports into the tree.
[bhelgaas: changelog, add comment]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=94361
Link: http://lkml.kernel.org/r/54EB81B2.4050904@pobox.com
Reported-by: Robert White <rwhite@pobox.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Rafael J. Wysocki