Extend the DSI PHY/PLL drivers to support the DSI 14nm PHY/PLL
found on 8x96.
These are picked up from the downstream driver. The PHY part is similar
to the other DSI PHYs. The PLL driver requires some trickery so that
one DSI PLL can drive both the DSIs (i.e, dual DSI mode).
In the case of dual DSI mode. One DSI instance becomes the clock master,
and other the clock slave. The master PLL's output (Byte and Pixel clock)
is fed to both the DSI hosts/PHYs.
When the DSIs are configured in dual DSI mode, the PHY driver communicates
to the PLL driver using msm_dsi_pll_set_usecase() which instance is the
master and which one is the slave. When setting rate, the master PLL also
configures some of the slave PLL/PHY registers which need to be identical
to the master's for correct dual DSI behaviour.
There are 2 PLL post dividers that should have ideally been modelled as
generic clk_divider clocks, but require some customization for dual DSI.
In particular, when the master PLL's post-diviers are set, the slave PLL's
post-dividers need to be set too. The clk_ops for these use clk_divider's
helper ops and flags internally to prevent redundant code.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Many DRM drivers only work with an MMU, and after the patch to enable
core DRM support without MMU, we already had one fixup for many of them.
The etnaviv, armada and msm drivers were missed and have the same problem:
warning: (DRM_ETNAVIV) selects IOMMU_SUPPORT which has unmet direct dependencies (MMU)
warning: (DRM_I915 && DRM_MSM && DRM_ETNAVIV) selects SHMEM which has unmet direct dependencies (MMU)
drivers/gpu/drm/armada/armada_gem.o: In function `armada_gem_vm_fault':
armada_gem.c:(.text.armada_gem_vm_fault+0x14): undefined reference to `vm_insert_pfn'
arch/arm/mm/dma-mapping.c: In function '__iommu_alloc_remap':
arch/arm/mm/dma-mapping.c:1390:4: error: 'VM_ARM_DMA_CONSISTENT' undeclared (first use in this function)
arch/arm/mm/dma-mapping.c:1456:31: error: 'atomic_pool' undeclared (first use in this function); did you mean 'atomic_xor'?
Fixes: 011cda5899 ("drm: fix compilations issues introduced by "drm: allow to use mmuless SoC"")
Fixes: 62a0d98a18 ("drm: allow to use mmuless SoC")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170111133357.3664191-2-arnd@arndb.de
This patch adds support to generic audio codec via
ASoC hdmi-codec infrastucture which is merged recently.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
[rebased on efc9194]
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI PHY on MSM8960 and APQ8064 is a 28nm PHY that's different from the
supported 28nm LP PHY found in newer chips.
Add support for the new PHY.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DRM_MSM_FBDEV config is used to enable/disable fbdev emulation for the
msm kms driver.
Replace this with the top level DRM_FBDEV_EMULATION config option where
applicable. This also prevents build breaks caused by undefined
drm_fb_helper_* functions when legacy fbdev support was disabled.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
On a certain platform, only one type of DSI PHY is used.
This change allows the user to only compile the PHY type
which is being used.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add HDMI HDCP support including HDCP PartI/II/III authentication.
V1: Initial Change
V2: Address Bjorn&Rob's comments
Refactor the authentication process to use single work instead
of multiple work for different authentication stages.
V3: Update to align with qcom SCM api.
Signed-off-by: Jilai Wang <jilaiw@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI byte clock and pixel clocks are sourced from DSI PLL.
This change adds the DSI PLL source clock driver under
common clock framework.
This change handles DSI 28nm PLL only.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Wentao Xu <wentaox@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change adds the DSI connector support in msm drm driver.
v1: Initial change
v2:
- Address comments from Archit + minor clean-ups
- Rebase to not depend on msm_drm_sub_dev change [Rob's comment]
v3: Fix issues when initialization is failed
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The msm gpu drivers depend on both the DT mechanism and the
common clk handling code, if they are not enabled, we get
a number of build errors:
In file included from drivers/gpu/drm/msm/hdmi/hdmi.h:27:0,
from drivers/gpu/drm/msm/hdmi/hdmi_bridge.c:18:
drivers/gpu/drm/msm/msm_drv.h:45:24: fatal error: mach/board.h: No such file or directory
#include <mach/board.h>
^
drivers/gpu/drm/msm/hdmi/hdmi_phy_8960.c:503:2: error: implicit declaration of function 'devm_clk_register' [-Werror=implicit-function-declaration]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Fixes a potential error, spotted by Felipe with randconfig:
-----
drivers/gpu/drm/msm/mdp/mdp4/mdp4_kms.c: In function ‘mdp4_kms_init’:
drivers/gpu/drm/msm/mdp/mdp4/mdp4_kms.c:384:2: error: implicit declaration \
of function ‘devm_regulator_get_exclusive’ [-Werror=implicit-function-declaration]
mdp4_kms->vdd = devm_regulator_get_exclusive(&pdev->dev, "vdd");
^
drivers/gpu/drm/msm/mdp/mdp4/mdp4_kms.c:384:16: error: assignment makes \
pointer from integer without a cast [-Werror]
mdp4_kms->vdd = devm_regulator_get_exclusive(&pdev->dev, "vdd");
^
-----
Also add a brief comment explaining the use of _get_exclusive()
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
LVDS panel support uses the LCDC (parallel) encoder. Unlike with HDMI,
there is not a separate LVDS block, so no need to split things into a
bridge+connector. Nor is there is anything re-used with mdp5.
Note that there can be some regulators shared between HDMI and LVDS (in
particular, on apq8064, ext_3v3p), so we should not use the _exclusive()
variants of devm_regulator_get().
The drm_panel framework is used for panel-specific driver.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Downstream kernel IOMMU had a non-standard way of dealing with multiple
devices and multiple ports/contexts. We don't need that on upstream
kernel, so rip out the crazy.
Note that we have to move the pinning of the ringbuffer to after the
IOMMU is attached. No idea how that managed to work properly on the
downstream kernel.
For now, I am leaving the IOMMU port name stuff in place, to simplify
things for folks trying to backport latest drm/msm to device kernels.
Once we no longer have to care about pre-DT kernels, we can drop this
and instead backport upstream IOMMU driver.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Architecture rename/split.. ARCH_QCOM is for the non-legacy platforms
(ie. device-tree, multiplatform support, etc).
Signed-off-by: Rob Clark <robdclark@gmail.com>
The ARCH_MSM depend is redundant with ARCH_MSM8960, so we can remove it.
Additionally, we are splitting Qualcomm MSM support into legacy (ARCH_MSM)
and multiplatform (ARCH_QCOM). The MSM8960 with be ARCH_QCOM going forward
so dropping ARCH_MSM will work properly for the new ARCH_QCOM multiplatform
build.
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Pull drm updates from Dave Airlie:
"Been a bit busy, first week of kids school, and waiting on other trees
to go in before I could send this, so its a bit later than I'd
normally like.
Highlights:
- core:
timestamp fixes, lots of misc cleanups
- new drivers:
bochs virtual vga
- vmwgfx:
major overhaul for their nextgen virt gpu.
- i915:
runtime D3 on HSW, watermark fixes, power well work, fbc fixes,
bdw is no longer prelim.
- nouveau:
gk110/208 acceleration, more pm groundwork, old overlay support
- radeon:
dpm rework and clockgating for CIK, pci config reset, big endian
fixes
- tegra:
panel support and DSI support, build as module, prime.
- armada, omap, gma500, rcar, exynos, mgag200, cirrus, ast:
fixes
- msm:
hdmi support for mdp5"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (595 commits)
drm/nouveau: resume display if any later suspend bits fail
drm/nouveau: fix lock unbalance in nouveau_crtc_page_flip
drm/nouveau: implement hooks for needed for drm vblank timestamping support
drm/nouveau/disp: add a method to fetch info needed by drm vblank timestamping
drm/nv50: fill in crtc mode struct members from crtc_mode_fixup
drm/radeon/dce8: workaround for atom BlankCrtc table
drm/radeon/DCE4+: clear bios scratch dpms bit (v2)
drm/radeon: set si_notify_smc_display_change properly
drm/radeon: fix DAC interrupt handling on DCE5+
drm/radeon: clean up active vram sizing
drm/radeon: skip async dma init on r6xx
drm/radeon/runpm: don't runtime suspend non-PX cards
drm/radeon: add ring to fence trace functions
drm/radeon: add missing trace point
drm/radeon: fix VMID use tracking
drm: ast,cirrus,mgag200: use drm_can_sleep
drm/gma500: Lock struct_mutex around cursor updates
drm/i915: Fix the offset issue for the stolen GEM objects
DRM: armada: fix missing DRM_KMS_FB_HELPER select
drm/i915: Decouple GPU error reporting from ring initialisation
...
The DRM driver for MSM depends on symbols from the MSM
IOMMU driver. Add this dependency to the Kconfig file.
Fixes this comile error:
Kernel: arch/arm/boot/zImage is ready
ERROR: "msm_iommu_get_ctx" [drivers/gpu/drm/msm/msm.ko]
undefined!
make[2]: *** [__modpost] Error 1
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
For drivers which might want to disable fbdev legacy support.
Select the new option in all drivers for now, so this shouldn't result
in any change. Drivers need some work anyway to make fbdev support
optional (if they have it implemented, that is), so the recommended
way to expose this is by adding per-driver options. At least as long
as most drivers don't support disabling the fbdev support.
v2: Update for new drm drivers msm and rcar-du. Note that Rob's msm
driver can already take advantage of this, which allows us to build
msm without any fbdev depencies in the kernel!
v3: Move the MODULE_* stuff from the fbdev helper file to
drm_crtc_helper.c.
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Acked-by: Dave Airlie <airlied@linux.ie>
Reviewed-by: Chon Ming Lee <chon.ming.lee@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The snapdragon chips have multiple different display controllers,
depending on which chip variant/version. (As far as I can tell, current
devices have either MDP3 or MDP4, and upcoming devices have MDSS.) And
then external to the display controller are HDMI, DSI, etc. blocks which
may be shared across devices which have different display controller
blocks.
To more easily add support for different display controller blocks, the
display controller specific bits are split out into a "kms" module,
which provides the kms plane/crtc/encoder objects.
The external HDMI, DSI, etc. blocks are part encoder, and part connector
currently. But I think I will pull in the drm_bridge patches from
chromeos tree, and split them into a bridge+connector, with the
registers that need to be set in modeset handled by the bridge. This
would remove the 'msm_connector' base class. But some things need to be
double checked to make sure I could get the correct ON/OFF sequencing..
This patch adds support for mdp4 crtc (including hw cursor), dtv encoder
(part of MDP4 block), and hdmi.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja