If something went wrong during the TPM firmware upgrade, like power
failure or the firmware image file get corrupted, the TPM might end
up in Upgrade or Failure mode upon the next start. The state is
persistent between the TPM power cycle/restart.
According to TPM specification:
* If the TPM is in Upgrade mode, it will answer with TPM2_RC_UPGRADE
to all commands except TPM2_FieldUpgradeData(). It may also accept
other commands if it is able to complete them using the previously
installed firmware.
* If the TPM is in Failure mode, it will allow performing TPM
initialization but will not provide any crypto operations.
Will happily respond to Field Upgrade calls.
Change the behavior of the tpm2_auto_startup(), so it detects the active
running mode of the TPM by adding the following checks. If
tpm2_do_selftest() call returns TPM2_RC_UPGRADE, the TPM is in Upgrade
mode.
If the TPM is in Failure mode, it will successfully respond to both
tpm2_do_selftest() and tpm2_startup() calls. Although, will fail to
answer to tpm2_get_cc_attrs_tbl(). Use this fact to conclude that TPM is
in Failure mode.
If detected that the TPM is in the Upgrade or Failure mode, the function
sets TPM_CHIP_FLAG_FIRMWARE_UPGRADE_MODE flag.
The TPM_CHIP_FLAG_FIRMWARE_UPGRADE_MODE flag is used later during driver
initialization/deinitialization to disable functionality which makes no
sense or will fail in the current TPM state. Following functionality is
affected:
* Do not register TPM as a hwrng
* Do not register sysfs entries which provide information impossible to
obtain in limited mode
* Do not register resource managed character device
Signed-off-by: axelj <axelj@axis.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
The Atmel TPM 1.2 chips crash with error
`tpm_try_transmit: send(): error -62` since kernel 4.14.
It is observed from the kernel log after running `tpm_sealdata -z`.
The error thrown from the command is as follows
```
$ tpm_sealdata -z
Tspi_Key_LoadKey failed: 0x00001087 - layer=tddl,
code=0087 (135), I/O error
```
The issue was reproduced with the following Atmel TPM chip:
```
$ tpm_version
T0 TPM 1.2 Version Info:
Chip Version: 1.2.66.1
Spec Level: 2
Errata Revision: 3
TPM Vendor ID: ATML
TPM Version: 01010000
Manufacturer Info: 41544d4c
```
The root cause of the issue is due to the TPM calls to msleep()
were replaced with usleep_range() [1], which reduces
the actual timeout. Via experiments, it is observed that
the original msleep(5) actually sleeps for 15ms.
Because of a known timeout issue in Atmel TPM 1.2 chip,
the shorter timeout than 15ms can cause the error described above.
A few further changes in kernel 4.16 [2] and 4.18 [3, 4] further
reduced the timeout to less than 1ms. With experiments,
the problematic timeout in the latest kernel is the one
for `wait_for_tpm_stat`.
To fix it, the patch reverts the timeout of `wait_for_tpm_stat`
to 15ms for all Atmel TPM 1.2 chips, but leave it untouched
for Ateml TPM 2.0 chip, and chips from other vendors.
As explained above, the chosen 15ms timeout is
the actual timeout before this issue introduced,
thus the old value is used here.
Particularly, TPM_ATML_TIMEOUT_WAIT_STAT_MIN is set to 14700us,
TPM_ATML_TIMEOUT_WAIT_STAT_MIN is set to 15000us according to
the existing TPM_TIMEOUT_RANGE_US (300us).
The fixed has been tested in the system with the affected Atmel chip
with no issues observed after boot up.
References:
[1] 9f3fc7bcdd tpm: replace msleep() with usleep_range() in TPM
1.2/2.0 generic drivers
[2] cf151a9a44 tpm: reduce tpm polling delay in tpm_tis_core
[3] 59f5a6b07f tpm: reduce poll sleep time in tpm_transmit()
[4] 424eaf910c tpm: reduce polling time to usecs for even finer
granularity
Fixes: 9f3fc7bcdd ("tpm: replace msleep() with usleep_range() in TPM 1.2/2.0 generic drivers")
Link: https://patchwork.kernel.org/project/linux-integrity/patch/20200926223150.109645-1-hao.wu@rubrik.com/
Signed-off-by: Hao Wu <hao.wu@rubrik.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
The current implementation appends a migratable flag to the end of a
key, meaning the format isn't exactly interoperable because the using
party needs to know to strip this extra byte. However, all other
consumers of TPM sealed blobs expect the unseal to return exactly the
key. Since TPM2 keys have a key property flag that corresponds to
migratable, use that flag instead and make the actual key the only
sealed quantity. This is secure because the key properties are bound
to a hash in the private part, so if they're altered the key won't
load.
Backwards compatibility is implemented by detecting whether we're
loading a new format key or not and correctly setting migratable from
the last byte of old format keys.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
When TPM 2.0 trusted keys code was moved to the trusted keys subsystem,
the operations were unwrapped from tpm_try_get_ops() and tpm_put_ops(),
which are used to take temporarily the ownership of the TPM chip. The
ownership is only taken inside tpm_send(), but this is not sufficient,
as in the key load TPM2_CC_LOAD, TPM2_CC_UNSEAL and TPM2_FLUSH_CONTEXT
need to be done as a one single atom.
Take the TPM chip ownership before sending anything with
tpm_try_get_ops() and tpm_put_ops(), and use tpm_transmit_cmd() to send
TPM commands instead of tpm_send(), reverting back to the old behaviour.
Fixes: 2e19e10131 ("KEYS: trusted: Move TPM2 trusted keys code")
Reported-by: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: stable@vger.kernel.org
Cc: David Howells <dhowells@redhat.com>
Cc: Mimi Zohar <zohar@linux.ibm.com>
Cc: Sumit Garg <sumit.garg@linaro.org>
Acked-by Sumit Garg <sumit.garg@linaro.org>
Tested-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Create sysfs per hash groups with 24 PCR files in them one group,
named pcr-<hash>, for each agile hash of the TPM. The files are
plugged in to a PCR read function which is TPM version agnostic, so
this works also for TPM 1.2 but the hash is only sha1 in that case.
Note: the macros used to create the hashes emit spurious checkpatch
warnings. Do not try to "fix" them as checkpatch recommends, otherwise
they'll break.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Tested-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Tested-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
The size of the buffers for storing context's and sessions can vary from
arch to arch as PAGE_SIZE can be anything between 4 kB and 256 kB (the
maximum for PPC64). Define a fixed buffer size set to 16 kB. This should be
enough for most use with three handles (that is how many we allow at the
moment). Parametrize the buffer size while doing this, so that it is easier
to revisit this later on if required.
Cc: stable@vger.kernel.org
Reported-by: Stefan Berger <stefanb@linux.ibm.com>
Fixes: 745b361e98 ("tpm: infrastructure for TPM spaces")
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The original code, before it was moved into security/keys/trusted-keys
had a flush after the blob unseal. Without that flush, the volatile
handles increase in the TPM until it becomes unusable and the system
either has to be rebooted or the TPM volatile area manually flushed.
Fix by adding back the lost flush, which we now have to export because
of the relocation of the trusted key code may cause the consumer to be
modular.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fixes: 2e19e10131 ("KEYS: trusted: Move TPM2 trusted keys code")
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Move TPM2 trusted keys code to trusted keys subsystem. The reason
being it's better to consolidate all the trusted keys code to a single
location so that it can be maintained sanely.
Also, utilize existing tpm_send() exported API which wraps the internal
tpm_transmit_cmd() API.
Suggested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Move tpm_buf code to common include/linux/tpm.h header so that it can
be reused via other subsystems like trusted keys etc.
Also rename trusted keys and asymmetric keys usage of TPM 1.x buffer
implementation to tpm1_buf to avoid any compilation errors.
Suggested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Patch adds method ->update_durations to override returned
durations in case TPM chip misbehaves for TPM 1.2 drivers.
Cc: Peter Huewe <peterhuewe@gmx.de>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Signed-off-by: Alexey Klimov <aklimov@redhat.com>
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> (!update_durations path)
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 315 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.503150771@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, tpm_pcr_extend() accepts as an input only a SHA1 digest.
This patch replaces the hash parameter of tpm_pcr_extend() with an array of
tpm_digest structures, so that the caller can provide a digest for each PCR
bank currently allocated in the TPM.
tpm_pcr_extend() will not extend banks for which no digest was provided,
as it happened before this patch, but instead it requires that callers
provide the full set of digests. Since the number of digests will always be
chip->nr_allocated_banks, the count parameter has been removed.
Due to the API change, ima_pcr_extend() and pcrlock() have been modified.
Since the number of allocated banks is not known in advance, the memory for
the digests must be dynamically allocated. To avoid performance degradation
and to avoid that a PCR extend is not done due to lack of memory, the array
of tpm_digest structures is allocated by the users of the TPM driver at
initialization time.
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Mimi Zohar <zohar@linux.ibm.com> (on x86 for TPM 1.2 & PTT TPM 2.0)
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The tpm_chip structure contains the list of PCR banks currently allocated
in the TPM. When support for crypto agility will be added to the TPM
driver, users of the driver have to provide a digest for each allocated
bank to tpm_pcr_extend(). With this patch, they can obtain the PCR bank
algorithms directly from chip->allocated_banks.
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Currently, the TPM driver retrieves the digest size from a table mapping
TPM algorithms identifiers to identifiers defined by the crypto subsystem.
If the algorithm is not defined by the latter, the digest size can be
retrieved from the output of the PCR read command.
The patch modifies the definition of tpm_pcr_read() and tpm2_pcr_read() to
pass the desired hash algorithm and obtain the digest size at TPM startup.
Algorithms and corresponding digest sizes are stored in the new structure
tpm_bank_info, member of tpm_chip, so that the information can be used by
other kernel subsystems.
tpm_bank_info contains: the TPM algorithm identifier, necessary to generate
the event log as defined by Trusted Computing Group (TCG); the digest size,
to pad/truncate a digest calculated with a different algorithm; the crypto
subsystem identifier, to calculate the digest of event data.
This patch also protects against data corruption that could happen in the
bus, by checking that the digest size returned by the TPM during a PCR read
matches the size of the algorithm passed to tpm2_pcr_read().
For the initial PCR read, when digest sizes are not yet available, this
patch ensures that the amount of data copied from the output returned by
the TPM does not exceed the size of the array data are copied to.
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Rename tpm2_* to tpm_* and move the definitions to include/linux/tpm.h so
that these can be used by other kernel subsystems (e.g. IMA).
Also, set the length of the digest array in tpm_digest to a new constant
named TPM_MAX_DIGEST_SIZE, equal to SHA512_DIGEST_SIZE.
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Acked-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Set tpm_chip->timeouts_adjusted directly in the update_timeouts
code instead of returning bool. In case of tpm read failing
print warning that the read failed and continue on.
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The TPM specs defines PCR index as a positive number, and there is
no reason to use a signed number. It is also a possible security
issue as currently no functions check for a negative index,
which may become a large number when converted to u32.
Adjust the API to use u32 instead of int in all PCR related
functions.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Implement tpm_default_chip() to find the first TPM chip and return it to
the caller while increasing the reference count on its device. This
function can be used by other subsystems, such as IMA, to find the system's
default TPM chip and use it for all subsequent TPM operations.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Fix tpm ptt initialization error:
tpm tpm0: A TPM error (378) occurred get tpm pcr allocation.
We cannot use go_idle cmd_ready commands via runtime_pm handles
as with the introduction of localities this is no longer an optional
feature, while runtime pm can be not enabled.
Though cmd_ready/go_idle provides a power saving, it's also a part of
TPM2 protocol and should be called explicitly.
This patch exposes cmd_read/go_idle via tpm class ops and removes
runtime pm support as it is not used by any driver.
When calling from nested context always use both flags:
TPM_TRANSMIT_UNLOCKED and TPM_TRANSMIT_RAW. Both are needed to resolve
tpm spaces and locality request recursive calls to tpm_transmit().
TPM_TRANSMIT_RAW should never be used standalone as it will fail
on double locking. While TPM_TRANSMIT_UNLOCKED standalone should be
called from non-recursive locked contexts.
New wrappers are added tpm_cmd_ready() and tpm_go_idle() to
streamline tpm_try_transmit code.
tpm_crb no longer needs own power saving functions and can drop using
tpm_pm_suspend/resume.
This patch cannot be really separated from the locality fix.
Fixes: 888d867df4 (tpm: cmd_ready command can be issued only after granting locality)
Cc: stable@vger.kernel.org
Fixes: 888d867df4 (tpm: cmd_ready command can be issued only after granting locality)
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
The correct sequence is to first request locality and only after
that perform cmd_ready handshake, otherwise the hardware will drop
the subsequent message as from the device point of view the cmd_ready
handshake wasn't performed. Symmetrically locality has to be relinquished
only after going idle handshake has completed, this requires that
go_idle has to poll for the completion and as well locality
relinquish has to poll for completion so it is not overridden
in back to back commands flow.
Two wrapper functions are added (request_locality relinquish_locality)
to simplify the error handling.
The issue is only visible on devices that support multiple localities.
Fixes: 877c57d0d0 ("tpm_crb: request and relinquish locality 0")
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkine@linux.intel.com>
Commit 5e572cab92 ("tpm: Enable CLKRUN protocol for Braswell
systems") disabled CLKRUN protocol during TPM transactions and re-enabled
once the transaction is completed. But there were still some corner cases
observed where, reading of TPM header failed for savestate command
while going to suspend, which resulted in suspend failure.
To fix this issue keep the CLKRUN protocol disabled for the entire
duration of a single TPM command and not disabling and re-enabling
again for every TPM transaction. For the other TPM accesses outside
TPM command flow, add a higher level of disabling and re-enabling
the CLKRUN protocol, instead of doing for every TPM transaction.
Fixes: 5e572cab92 ("tpm: Enable CLKRUN protocol for Braswell systems")
Signed-off-by: Azhar Shaikh <azhar.shaikh@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Device number (the character device index) is not a stable identifier
for a TPM chip. That is the reason why every call site passes
TPM_ANY_NUM to tpm_chip_find_get().
This commit changes the API in a way that instead a struct tpm_chip
instance is given and NULL means the default chip. In addition, this
commit refines the documentation to be up to date with the
implementation.
Suggested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com> (@chip_num -> @chip part)
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jason Gunthorpe <jgg@ziepe.ca>
Tested-by: PrasannaKumar Muralidharan <prasannatsmkumar@gmail.com>
This commit adds support for requesting and relinquishing locality 0 in
tpm_crb for the course of command transmission.
In order to achieve this, two new callbacks are added to struct
tpm_class_ops:
- request_locality
- relinquish_locality
With CRB interface you first set either requestAccess or relinquish bit
from TPM_LOC_CTRL_x register and then wait for locAssigned and
tpmRegValidSts bits to be set in the TPM_LOC_STATE_x register.
The reason why were are doing this is to make sure that the driver
will work properly with Intel TXT that uses locality 2. There's no
explicit guarantee that it would relinquish this locality. In more
general sense this commit enables tpm_crb to be a well behaving
citizen in a multi locality environment.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Tested-by: Jerry Snitselaar <jsnitsel@redhat.com>
The TCG standard startup sequence (get timeouts, tpm startup, etc) for
TPM and TPM2 chips is being open coded in many drivers, move it into
the core code.
tpm_tis and tpm_crb are used as the basis for the core code
implementation and the easy drivers are converted. In the process
several small drivers bugs relating to error handling this flow
are fixed.
For now the flag TPM_OPS_AUTO_STARTUP is optional to allow a staged
driver roll out, but ultimately all drivers should use this flow and
the flag removed. Some drivers still do not implement the startup
sequence at all and will need to be tested with it enabled.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Andrew Zamansky <andrew.zamansky@nuvoton.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Added tpm_trusted_seal() and tpm_trusted_unseal() API for sealing
trusted keys.
This patch implements basic sealing and unsealing functionality for
TPM 2.0:
* Seal with a parent key using a 20 byte auth value.
* Unseal with a parent key using a 20 byte auth value.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Some Atmel TPMs provide completely wrong timeouts from their
TPM_CAP_PROP_TIS_TIMEOUT query. This patch detects that and returns
new correct values via a DID/VID table in the TIS driver.
Tested on ARM using an AT97SC3204T FW version 37.16
Cc: <stable@vger.kernel.org>
[PHuewe: without this fix these 'broken' Atmel TPMs won't function on
older kernels]
Signed-off-by: "Berg, Christopher" <Christopher.Berg@atmel.com>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
This replaces the static initialization of a tpm_vendor_specific
structure in the drivers with the standard Linux idiom of providing
a const structure of function pointers.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Reviewed-by: Ashley Lai <adlai@linux.vnet.ibm.com>
[phuewe: did apply manually due to commit
191ffc6bde3 tpm/tpm_i2c_atmel: fix coccinelle warnings]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
IMA requires access to TPM_DIGEST_SIZE definition. This patch
moves the definition to <linux/tpm.h>.
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Move the tpm_get_random api from the trusted keys code into the TPM
device driver itself so that other callers can make use of it. Also,
change the api slightly so that the number of bytes read is returned in
the call, since the TPM command can potentially return fewer bytes than
requested.
Acked-by: David Safford <safford@linux.vnet.ibm.com>
Reviewed-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Add internal kernel tpm_send() command used to seal/unseal keys.
Changelog:
- replaced module_put in tpm_send() with new tpm_chip_put() wrapper
(suggested by David Howells)
- Make tpm_send() cmd argument a 'void *' (suggested by David Howells)
Signed-off-by: David Safford <safford@watson.ibm.com>
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Signed-off-by: James Morris <jmorris@namei.org>
Fix build for TCG_TPM=m. Header file doesn't handle this
and incorrectly builds stubs.
drivers/char/tpm/tpm.c:720: error: redefinition of 'tpm_pcr_read'
include/linux/tpm.h:35: error:previous definition of 'tpm_pcr_read' was here
drivers/char/tpm/tpm.c:752: error: redefinition of 'tpm_pcr_extend'
include/linux/tpm.h:38: error:previous definition of 'tpm_pcr_extend' was here
Repairs linux-next's
commit d6ba452128
Author: Mimi Zohar <zohar@linux.vnet.ibm.com>
Date: Mon Oct 26 09:26:18 2009 -0400
tpm add default function definitions
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Cc: Mimi Zohar <zohar@us.ibm.com>
Cc: James Morris <jmorris@namei.org>
Cc: Eric Paris <eparis@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Morris <jmorris@namei.org>
Add default tpm_pcr_read/extend function definitions required
by IMA/Kconfig changes.
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Reviewed-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
This patch adds internal kernel support for:
- reading/extending a pcr value
- looking up the tpm_chip for a given chip number
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
axelj