For VLAN-unaware bridging, tag_8021q uses something perhaps a bit too
tied with the sja1105 switch: each port uses the same pvid which is also
used for standalone operation (a unique one from which the source port
and device ID can be retrieved when packets from that port are forwarded
to the CPU). Since each port has a unique pvid when performing
autonomous forwarding, the switch must be configured for Shared VLAN
Learning (SVL) such that the VLAN ID itself is ignored when performing
FDB lookups. Without SVL, packets would always be flooded, since FDB
lookup in the source port's VLAN would never find any entry.
First of all, to make tag_8021q more palatable to switches which might
not support Shared VLAN Learning, let's just use a common VLAN for all
ports that are under the same bridge.
Secondly, using Shared VLAN Learning means that FDB isolation can never
be enforced. But if all ports under the same VLAN-unaware bridge share
the same VLAN ID, it can.
The disadvantage is that the CPU port can no longer perform precise
source port identification for these packets. But at least we have a
mechanism which has proven to be adequate for that situation: imprecise
RX (dsa_find_designated_bridge_port_by_vid), which is what we use for
termination on VLAN-aware bridges.
The VLAN ID that VLAN-unaware bridges will use with tag_8021q is the
same one as we were previously using for imprecise TX (bridge TX
forwarding offload). It is already allocated, it is just a matter of
using it.
Note that because now all ports under the same bridge share the same
VLAN, the complexity of performing a tag_8021q bridge join decreases
dramatically. We no longer have to install the RX VLAN of a newly
joining port into the port membership of the existing bridge ports.
The newly joining port just becomes a member of the VLAN corresponding
to that bridge, and the other ports are already members of it from when
they joined the bridge themselves. So forwarding works properly.
This means that we can unhook dsa_tag_8021q_bridge_{join,leave} from the
cross-chip notifier level dsa_switch_bridge_{join,leave}. We can put
these calls directly into the sja1105 driver.
With this new mode of operation, a port controlled by tag_8021q can have
two pvids whereas before it could only have one. The pvid for standalone
operation is different from the pvid used for VLAN-unaware bridging.
This is done, again, so that FDB isolation can be enforced.
Let tag_8021q manage this by deleting the standalone pvid when a port
joins a bridge, and restoring it when it leaves it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a single argument to dsa_8021q_rx_vid and dsa_8021q_tx_vid that
contains the necessary information from the two arguments that are
currently provided: the switch and the port number.
Also rename those functions so that they have a dsa_port_* prefix, since
they operate on a struct dsa_port *.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/mptcp/protocol.c
977d293e23 ("mptcp: ensure tx skbs always have the MPTCP ext")
efe686ffce ("mptcp: ensure tx skbs always have the MPTCP ext")
same patch merged in both trees, keep net-next.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Now that the sja1105 driver is finally sane enough again to stop having
a ternary VLAN awareness state, we can remove priv->vlan_aware and query
DSA for the ds->vlan_filtering value (for SJA1105, VLAN filtering is a
global property).
Also drop the paranoid checking that DSA calls ->port_vlan_filtering
multiple times without the VLAN awareness state changing. It doesn't,
the same check is present inside dsa_port_vlan_filtering too.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NXP Legal insists that the following are not fine:
- Saying "NXP Semiconductors" instead of "NXP", since the company's
registered name is "NXP"
- Putting a "(c)" sign in the copyright string
- Putting a comma in the copyright string
The only accepted copyright string format is "Copyright <year-range> NXP".
This patch changes the copyright headers in the networking files that
were sent by me, or derived from code sent by me.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simply put, the best-effort VLAN filtering mode relied on VLAN retagging
from a bridge VLAN towards a tag_8021q sub-VLAN in order to be able to
decode the source port in the tagger, but the VLAN retagging
implementation inside the sja1105 chips is not the best and we were
relying on marginal operating conditions.
The most notable limitation of the best-effort VLAN filtering mode is
its incapacity to treat this case properly:
ip link add br0 type bridge vlan_filtering 1
ip link set swp2 master br0
ip link set swp4 master br0
bridge vlan del dev swp4 vid 1
bridge vlan add dev swp4 vid 1 pvid
When sending an untagged packet through swp2, the expectation is for it
to be forwarded to swp4 as egress-tagged (so it will contain VLAN ID 1
on egress). But the switch will send it as egress-untagged.
There was an attempt to fix this here:
https://patchwork.kernel.org/project/netdevbpf/patch/20210407201452.1703261-2-olteanv@gmail.com/
but it failed miserably because it broke PTP RX timestamping, in a way
that cannot be corrected due to hardware issues related to VLAN
retagging.
So with either PTP broken or pushing VLAN headers on egress for untagged
packets being broken, the sad reality is that the best-effort VLAN
filtering code is broken. Delete it.
Note that this means there will be a temporary loss of functionality in
this driver until it is replaced with something better (network stack
RX/TX capability for "mode 2" as described in
Documentation/networking/dsa/sja1105.rst, the "port under VLAN-aware
bridge" case). We simply cannot keep this code until that driver rework
is done, it is super bloated and tangled with tag_8021q.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a SJA1105_MAX_NUM_PORTS macro which at the moment is equal to
SJA1105_NUM_PORTS (5). With the introduction of SJA1110, these
structures will need to hold information for up to 11 ports.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes in xfrm_device.c, between the double
ESP trailing bug fix setting the XFRM_INIT flag and the changes
in net-next preparing for bonding encryption support.
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105_gating_cfg_time_to_interval function does this, as per the
comments:
/* The gate entries contain absolute times in their e->interval field. Convert
* that to proper intervals (i.e. "0, 5, 10, 15" to "5, 5, 5, 5").
*/
To perform that task, it iterates over gating_cfg->entries, at each step
updating the interval of the _previous_ entry. So one interval remains
to be updated at the end of the loop: the last one (since it isn't
"prev" for anyone else).
But there was an erroneous check, that the last element's interval
should not be updated if it's also the only element. I'm not quite sure
why that check was there, but it's clearly incorrect, as a tc-gate
schedule with a single element would get an e->interval of zero,
regardless of the duration requested by the user. The switch wouldn't
even consider this configuration as valid: it will just drop all traffic
that matches the rule.
Fixes: 834f8933d5 ("net: dsa: sja1105: implement tc-gate using time-triggered virtual links")
Reported-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, tas_data->enabled would remain true even after deleting all
tc-gate rules from the switch ports, which would cause the
sja1105_tas_state_machine to get unnecessarily scheduled.
Also, if there were any errors which would prevent the hardware from
enabling the gating schedule, the sja1105_tas_state_machine would
continuously detect and print that, spamming the kernel log, even if the
rules were subsequently deleted.
The rules themselves are _not_ active, because sja1105_init_scheduling
does enough of a job to not install the gating schedule in the static
config. But the virtual link rules themselves are still present.
So call the functions that remove the tc-gate configuration from
priv->tas_data.gating_cfg, so that tas_data->enabled can be set to
false, and sja1105_tas_state_machine will stop from being scheduled.
Fixes: 834f8933d5 ("net: dsa: sja1105: implement tc-gate using time-triggered virtual links")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently sja1105_compose_gating_subschedule is not prepared to be
called for the case where we want to recompute the global tc-gate
configuration after we've deleted those actions on a port.
After deleting the tc-gate actions on the last port, max_cycle_time
would become zero, and that would incorrectly prevent
sja1105_free_gating_config from getting called.
So move the freeing function above the check for the need to apply a new
configuration.
Fixes: 834f8933d5 ("net: dsa: sja1105: implement tc-gate using time-triggered virtual links")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It turns out that sja1105_compose_gating_subschedule must also be called
from sja1105_vl_delete, to recalculate the overall tc-gate
configuration. Currently this is not possible without introducing a
forward declaration. So move the function at the top of the file, along
with its dependencies.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a drop frames counter to tc flower offloading.
Reporting h/w dropped frames is necessary for some actions.
Some actions like police action and the coming introduced stream gate
action would produce dropped frames which is necessary for user. Status
update shows how many filtered packets increasing and how many dropped
in those packets.
v2: Changes
- Update commit comments suggest by Jiri Pirko.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This action requires the VLAN awareness state of the switch to be of the
same type as the key that's being added:
- If the switch is unaware of VLAN, then the tc filter key must only
contain the destination MAC address.
- If the switch is VLAN-aware, the key must also contain the VLAN ID and
PCP.
But this check doesn't work unless we verify the VLAN awareness state on
both the "if" and the "else" branches.
Fixes: 834f8933d5 ("net: dsa: sja1105: implement tc-gate using time-triggered virtual links")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This action requires the VLAN awareness state of the switch to be of the
same type as the key that's being added:
- If the switch is unaware of VLAN, then the tc filter key must only
contain the destination MAC address.
- If the switch is VLAN-aware, the key must also contain the VLAN ID and
PCP.
But this check doesn't work unless we verify the VLAN awareness state on
both the "if" and the "else" branches.
Fixes: dfacc5a23e ("net: dsa: sja1105: support flow-based redirection via virtual links")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This shouldn't be there.
Fixes: 834f8933d5 ("net: dsa: sja1105: implement tc-gate using time-triggered virtual links")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer C compilers are complaining about the fact that there are no
function prototypes in sja1105_vl.c for the non-static functions.
Give them what they want.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 different features that require some reserved frame memory
space: VLAN retagging and virtual links. Create a central function that
modifies the static config and ensures frame memory is never
overcommitted.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Soon we'll add a third operating mode to the driver. Introduce a
vlan_state to make things more easy to manage, and use it where
applicable.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/dsa/sja1105/sja1105_vl.c:468:6: warning: variable ‘prev_time’ set but not used [-Wunused-but-set-variable]
u32 prev_time = 0;
^~~~~~~~~
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Samuel Zou <zou_wei@huawei.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Restrict the TTEthernet hardware support on this switch to operate as
closely as possible to IEEE 802.1Qci as possible. This means that it can
perform PTP-time-based ingress admission control on streams identified
by {DMAC, VID, PCP}, which is useful when trying to ensure the
determinism of traffic scheduled via IEEE 802.1Qbv.
The oddity comes from the fact that in hardware (and in TTEthernet at
large), virtual links always need a full-blown action, including not
only the type of policing, but also the list of destination ports. So in
practice, a single tc-gate action will result in all packets getting
dropped. Additional actions (either "trap" or "redirect") need to be
specified in the same filter rule such that the conforming packets are
actually forwarded somewhere.
Apart from the VL Lookup, Policing and Forwarding tables which need to
be programmed for each flow (virtual link), the Schedule engine also
needs to be told to open/close the admission gates for each individual
virtual link. A fairly accurate (and detailed) description of how that
works is already present in sja1105_tas.c, since it is already used to
trigger the egress gates for the tc-taprio offload (IEEE 802.1Qbv). Key
point here, we remember that the schedule engine supports 8
"subschedules" (execution threads that iterate through the global
schedule in parallel, and that no 2 hardware threads must execute a
schedule entry at the same time). For tc-taprio, each egress port used
one of these 8 subschedules, leaving a total of 4 subschedules unused.
In principle we could have allocated 1 subschedule for the tc-gate
offload of each ingress port, but actually the schedules of all virtual
links installed on each ingress port would have needed to be merged
together, before they could have been programmed to hardware. So
simplify our life and just merge the entire tc-gate configuration, for
all virtual links on all ingress ports, into a single subschedule. Be
sure to check that against the usual hardware scheduling conflicts, and
program it to hardware alongside any tc-taprio subschedule that may be
present.
The following scenarios were tested:
1. Quantitative testing:
tc qdisc add dev swp2 clsact
tc filter add dev swp2 ingress flower skip_sw \
dst_mac 42:be:24:9b:76:20 \
action gate index 1 base-time 0 \
sched-entry OPEN 1200 -1 -1 \
sched-entry CLOSE 1200 -1 -1 \
action trap
ping 192.168.1.2 -f
PING 192.168.1.2 (192.168.1.2) 56(84) bytes of data.
.............................
--- 192.168.1.2 ping statistics ---
948 packets transmitted, 467 received, 50.7384% packet loss, time 9671ms
2. Qualitative testing (with a phase-aligned schedule - the clocks are
synchronized by ptp4l, not shown here):
Receiver (sja1105):
tc qdisc add dev swp2 clsact
now=$(phc_ctl /dev/ptp1 get | awk '/clock time is/ {print $5}') && \
sec=$(echo $now | awk -F. '{print $1}') && \
base_time="$(((sec + 2) * 1000000000))" && \
echo "base time ${base_time}"
tc filter add dev swp2 ingress flower skip_sw \
dst_mac 42:be:24:9b:76:20 \
action gate base-time ${base_time} \
sched-entry OPEN 60000 -1 -1 \
sched-entry CLOSE 40000 -1 -1 \
action trap
Sender (enetc):
now=$(phc_ctl /dev/ptp0 get | awk '/clock time is/ {print $5}') && \
sec=$(echo $now | awk -F. '{print $1}') && \
base_time="$(((sec + 2) * 1000000000))" && \
echo "base time ${base_time}"
tc qdisc add dev eno0 parent root taprio \
num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
base-time ${base_time} \
sched-entry S 01 50000 \
sched-entry S 00 50000 \
flags 2
ping -A 192.168.1.1
PING 192.168.1.1 (192.168.1.1): 56 data bytes
...
^C
--- 192.168.1.1 ping statistics ---
1425 packets transmitted, 1424 packets received, 0% packet loss
round-trip min/avg/max = 0.322/0.361/0.990 ms
And just for comparison, with the tc-taprio schedule deleted:
ping -A 192.168.1.1
PING 192.168.1.1 (192.168.1.1): 56 data bytes
...
^C
--- 192.168.1.1 ping statistics ---
33 packets transmitted, 19 packets received, 42% packet loss
round-trip min/avg/max = 0.336/0.464/0.597 ms
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement tc-flower offloads for redirect, trap and drop using
non-critical virtual links.
Commands which were tested to work are:
# Send frames received on swp2 with a DA of 42:be:24:9b:76:20 to the
# CPU and to swp3. This type of key (DA only) when the port's VLAN
# awareness state is off.
tc qdisc add dev swp2 clsact
tc filter add dev swp2 ingress flower skip_sw dst_mac 42:be:24:9b:76:20 \
action mirred egress redirect dev swp3 \
action trap
# Drop frames received on swp2 with a DA of 42:be:24:9b:76:20, a VID
# of 100 and a PCP of 0.
tc filter add dev swp2 ingress protocol 802.1Q flower skip_sw \
dst_mac 42:be:24:9b:76:20 vlan_id 100 vlan_prio 0 action drop
Under the hood, all rules match on DMAC, VID and PCP, but when VLAN
filtering is disabled, those are set internally by the driver to the
port-based defaults. Because we would be put in an awkward situation if
the user were to change the VLAN filtering state while there are active
rules (packets would no longer match on the specified keys), we simply
deny changing vlan_filtering unless the list of flows offloaded via
virtual links is empty. Then the user can re-add new rules.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean