During my recent work on the rtnl lock deadlock in the IPoIB driver, I
saw that even once I fixed the apparent races for a single device, as
soon as that device had any children, new races popped up. It turns
out that this is because no matter how well we protect against races
on a single device, the fact that all devices use the same workqueue,
and flush_workqueue() flushes *everything* from that workqueue means
that we would also have to prevent all races between different devices
(for instance, ipoib_mcast_restart_task on interface ib0 can race with
ipoib_mcast_flush_dev on interface ib0.8002, resulting in a deadlock on
the rtnl_lock).
There are several possible solutions to this problem:
Make carrier_on_task and mcast_restart_task try to take the rtnl for
some set period of time and if they fail, then bail. This runs the
real risk of dropping work on the floor, which can end up being its
own separate kind of deadlock.
Set some global flag in the driver that says some device is in the
middle of going down, letting all tasks know to bail. Again, this can
drop work on the floor.
Or the method this patch attempts to use, which is when we bring an
interface up, create a workqueue specifically for that interface, so
that when we take it back down, we are flushing only those tasks
associated with our interface. In addition, keep the global
workqueue, but now limit it to only flush tasks. In this way, the
flush tasks can always flush the device specific work queues without
having deadlock issues.
Signed-off-by: Doug Ledford <dledford@redhat.com>
We blindly assume that we can just take the rtnl lock and that will
prevent races with downing this interface. Unfortunately, that's not
the case. In ipoib_mcast_stop_thread() we will call flush_workqueue()
in an attempt to clear out all remaining instances of ipoib_join_task.
But, since this task is put on the same workqueue as the join task,
the flush_workqueue waits on this thread too. But this thread is
deadlocked on the rtnl lock. The better thing here is to use trylock
and loop on that until we either get the lock or we see that
FLAG_OPER_UP has been cleared, in which case we don't need to do
anything anyway and we just return.
While investigating which flag should be used, FLAG_ADMIN_UP or
FLAG_OPER_UP, it was determined that FLAG_OPER_UP was the more
appropriate flag to use. However, there was a mix of these two flags in
use in the existing code. So while we check for that flag here as part
of this race fix, also cleanup the two places that had used the less
appropriate flag for their tests.
Signed-off-by: Doug Ledford <dledford@redhat.com>
The ipoib_mcast_flush_dev routine is called with the rtnl_lock held and
needs to keep it held. It also needs to call flush_workqueue() to flush
out any outstanding work. In the past, we've had to try and make sure
that we didn't flush out any outstanding join completions because they
also wanted to grab rtnl_lock() and that would deadlock. It turns out
that the only thing in the join completion handler that needs this lock
can be safely moved to our carrier_on_task, thereby reducing the
potential for the join completion code and the flush code to deadlock
against each other.
Signed-off-by: Doug Ledford <dledford@redhat.com>
In preparation for using per device work queues, we need to move the
start of the neighbor thread task to after ipoib_ib_dev_init and move
the destruction of the neighbor task to before ipoib_ib_dev_cleanup.
Otherwise we will end up freeing our workqueue with work possibly
still on it.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Create a an ipoib_flush_ah and ipoib_stop_ah routines to use at
appropriate times to flush out all remaining ah entries before we shut
the device down.
Because neighbors and mcast entries can each have a reference on any
given ah, we must make sure to free all of those first before our ah
will actually have a 0 refcount and be able to be reaped.
This factoring is needed in preparation for having per-device work
queues. The original per-device workqueue code resulted in the following
error message:
<ibdev>: ib_dealloc_pd failed
That error was tracked down to this issue. With the changes to which
workqueues were flushed when, there were no flushes of the per device
workqueue after the last ah's were freed, resulting in an attempt to
dealloc the pd with outstanding resources still allocated. This code
puts the explicit flushes in the needed places to avoid that problem.
Signed-off-by: Doug Ledford <dledford@redhat.com>
In a call to ib_umem_get(), if address is 0x0 and size is
already page aligned, check added in commit 8494057ab5
("IB/uverbs: Prevent integer overflow in ib_umem_get address
arithmetic") will refuse to register a memory region that
could otherwise be valid (provided vm.mmap_min_addr sysctl
and mmap_low_allowed SELinux knobs allow userspace to map
something at address 0x0).
This patch allows back such registration: ib_umem_get()
should probably don't care of the base address provided it
can be pinned with get_user_pages().
There's two possible overflows, in (addr + size) and in
PAGE_ALIGN(addr + size), this patch keep ensuring none
of them happen while allowing to pin memory at address
0x0. Anyway, the case of size equal 0 is no more (partially)
handled as 0-length memory region are disallowed by an
earlier check.
Link: http://mid.gmane.org/cover.1428929103.git.ydroneaud@opteya.com
Cc: <stable@vger.kernel.org> # 8494057ab5 ("IB/uverbs: Prevent integer overflow in ib_umem_get address arithmetic")
Cc: Shachar Raindel <raindel@mellanox.com>
Cc: Jack Morgenstein <jackm@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If ib_umem_get() is called with a size equal to 0 and an
non-page aligned address, one page will be pinned and a
0-sized umem will be returned to the caller.
This should not be allowed: it's not expected for a memory
region to have a size equal to 0.
This patch adds a check to explicitly refuse to register
a 0-sized region.
Link: http://mid.gmane.org/cover.1428929103.git.ydroneaud@opteya.com
Cc: <stable@vger.kernel.org>
Cc: Shachar Raindel <raindel@mellanox.com>
Cc: Jack Morgenstein <jackm@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Change the default mode to be HOST assigned instead of SM assigned. This is
the expected operational mode, because it doesn't depend on SM availability.
As PF generates random GUIDs as the initial admin values, this gives
out of the box experience.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Request GIDs from the SM on demand, i.e., when a VF actually needs them,
and release them when the GIDs are no longer in use.
In cloud environments, this is useful for GID migrations, in which a
GID is assigned to a VF on the destination HCA, while the VF on the
source HCA is shutdown (but the GID was not administratively released).
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Change the init flow to ask GUIDs only for active VFs. This is done for
both SM & HOST modes so that there is no need any more to maintain the
ownership record type.
In case SM mode is used, the initial value will be 0, ask the SM to assign,
for the HOST mode the initial value will be the HOST generated GUID.
This will enable out of the box experience for both probed and attached VFs.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Set the admin alias GUID per the administrator's request via the sysfs
mechanism into the core layer.
The "get" request returns the current value. However, if the administrator
requests the SM to assign a new value by requesting 0, the SM assigned
GUID is returned.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If the SM rejects an alias GUID request the PF driver keeps trying to acquire
the specified GUID indefinitely, utilizing an exponential backoff scheme.
Retrying is managed per GUID entry. Each entry that wasn't applied holds its
next retry information. Retry requests to the SM consist of records of 8
consecutive GUIDS. Each record that contains GUIDs requiring retries holds its
next time-to-run based on the retry information of all its GUID entries. The
record having the lowest retry time will run first when that retry time
arrives.
Since the method (SET or DELETE) as sent to the SM applies to all the GUIDs in
the record, we must handle SET requests and DELETE requests in separate SM
messages (one for SETs and the other for DELETEs).
To avoid race conditions where a GUID entry request (set or delete) was
modified after the SM request was sent, we save the method and the requested
indices as part of the callback's context -- thus, only the requested indexes
are evaluated when the response is received.
When an GUID entry is approved we turn off its retry-required bit, this
prevents redundant SM retries from occurring on that record.
The port down event should be sent only when previously it was up. Likewise,
the port up event should be sent only if previously the port was down.
Synchronization was added around the flows that change entries and record state
to prevent race conditions.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Instead of calling target_fabric_configfs_init() +
target_fabric_configfs_register() / target_fabric_configfs_deregister()
target_fabric_configfs_free() from every target driver, rewrite the API
so that we have simple register/unregister functions that operate on
a const operations vector.
This patch also fixes a memory leak in several target drivers. Several
target drivers namely called target_fabric_configfs_deregister()
without calling target_fabric_configfs_free().
A large part of this patch is based on earlier changes from
Bart Van Assche <bart.vanassche@sandisk.com>.
(v2: Add a new TF_CIT_SETUP_DRV macro so that the core configfs code
can declare attributes as either core only or for drivers)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Things Not To Do When Writing A Driver, part 1001st:
have writev() and write() on the same file doing completely
different things. As in, "interpret very different sets of
commands".
We _can_ handle that, but it's a bloody bad idea.
Don't do that in new drivers. Ever.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
trivial conflict in net/socket.c and non-trivial one in crypto -
that one had evaded aio_complete() removal.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
These variables are always accessed via struct isert_conn so
no need to have a "conn_" prefix for them.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
iser target can handle as many connect request as
the fabric sends to it. This backlog should not set as
a back-pressure mechanism (which is not very useful).
isert does need a back-pressure mechanism, but it should
be added in isert by monitoring the number of pending
established connections (will be added in a later stage).
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In iser_connect_release there is no chance that
the iser device is set to NULL, if this happens
we have a BUG. So use BUG_ON.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Not sure what it was used for, but there is
no real need for it now as I see it. Go ahead
and get rid of it.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Move login buffer alloc/free code to dedicated
routines and introduce isert_conn_init which
initializes the connection lists and locks.
Simplifies and cleans up the code a little bit.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
isert_device_find_by_ib_dev and isert_device_try_release
can have a better, more common name like isert_device_[get|put].
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
No need to keep a local ib_dev as a device pointer.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Move the code for completion context handling to dedicated
routines. This simplifies the code and removes code duplication.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Simplify iser QP creation by splitting some unrelated
logic bulks to routines.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This is to favor the HCA cache hit rate using less MRs
and PDs. This commit partially reverts commit:
"eb6ab13 IB/isert: separate connection protection domains and dma MRs"
At the time I thought this would be needed.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Before we reach to connection established we may get an
error event. In this case the core won't teardown this
connection (never established it), so we take care of freeing
it ourselves.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This hang was a result of a missing command put when
a DIF error occurred during a rdma read (and we sent
an CHECK_CONDITION error without passing it to the
backend).
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Conflicts:
drivers/net/ethernet/mellanox/mlx4/cmd.c
net/core/fib_rules.c
net/ipv4/fib_frontend.c
The fib_rules.c and fib_frontend.c conflicts were locking adjustments
in 'net' overlapping addition and removal of code in 'net-next'.
The mlx4 conflict was a bug fix in 'net' happening in the same
place a constant was being replaced with a more suitable macro.
Signed-off-by: David S. Miller <davem@davemloft.net>
Preparation for ethernet driver.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass consumer index as a parameter to arm CQ
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preparation for ethernet driver.
These functions will be used in drivers other than mlx5_ib.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do it in one place instead of every where the function is invoked
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass 0 in the sqd_event parameter.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The calls to SET_PORT used hard-code numbers, when supplying command's
opcode modifiers, fix that to use well defined constants.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't use dev->iflink anymore.
CC: Roland Dreier <roland@kernel.org>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Properly verify that the resulting page aligned end address is larger
than both the start address and the length of the memory area requested.
Both the start and length arguments for ib_umem_get are controlled by
the user. A misbehaving user can provide values which will cause an
integer overflow when calculating the page aligned end address.
This overflow can cause also miscalculation of the number of pages
mapped, and additional logic issues.
Addresses: CVE-2014-8159
Cc: <stable@vger.kernel.org>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
struct kiocb now is a generic I/O container, so move it to fs.h.
Also do a #include diet for aio.h while we're at it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
For RoCE ports, we set the u32 PMA values based on u64 HCA counters. In case of
overflow, according to the IB spec, we have to saturate a counter to its
max value, do that.
Fixes: c37791349c ('IB/mlx4: Support PMA counters for IBoE')
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Processing an event is done in a different context from the one when
the event was dispatched. This requires a check that the slave
net device is still valid when the event is being processed. The check is done
under the iboe lock which ensure correctness.
Fixes: a575009030 ('IB/mlx4: Add port aggregation support')
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull more vfs updates from Al Viro:
"Assorted stuff from this cycle. The big ones here are multilayer
overlayfs from Miklos and beginning of sorting ->d_inode accesses out
from David"
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (51 commits)
autofs4 copy_dev_ioctl(): keep the value of ->size we'd used for allocation
procfs: fix race between symlink removals and traversals
debugfs: leave freeing a symlink body until inode eviction
Documentation/filesystems/Locking: ->get_sb() is long gone
trylock_super(): replacement for grab_super_passive()
fanotify: Fix up scripted S_ISDIR/S_ISREG/S_ISLNK conversions
Cachefiles: Fix up scripted S_ISDIR/S_ISREG/S_ISLNK conversions
VFS: (Scripted) Convert S_ISLNK/DIR/REG(dentry->d_inode) to d_is_*(dentry)
SELinux: Use d_is_positive() rather than testing dentry->d_inode
Smack: Use d_is_positive() rather than testing dentry->d_inode
TOMOYO: Use d_is_dir() rather than d_inode and S_ISDIR()
Apparmor: Use d_is_positive/negative() rather than testing dentry->d_inode
Apparmor: mediated_filesystem() should use dentry->d_sb not inode->i_sb
VFS: Split DCACHE_FILE_TYPE into regular and special types
VFS: Add a fallthrough flag for marking virtual dentries
VFS: Add a whiteout dentry type
VFS: Introduce inode-getting helpers for layered/unioned fs environments
Infiniband: Fix potential NULL d_inode dereference
posix_acl: fix reference leaks in posix_acl_create
autofs4: Wrong format for printing dentry
...
Pull SCSI target updates from Nicholas Bellinger:
"The highlights this round include:
- Update vhost-scsi to support F_ANY_LAYOUT using mm/iov_iter.c
logic, and signal VERSION_1 support (MST + Viro + nab)
- Fix iscsi/iser-target to remove problematic active_ts_set usage
(Gavin Guo)
- Update iscsi/iser-target to support multi-sequence sendtargets
(Sagi)
- Fix original PR_APTPL_BUF_LEN 8k size limitation (Martin Svec)
- Add missing WRITE_SAME end-of-device sanity check (Bart)
- Check for LBA + sectors wrap-around in sbc_parse_cdb() (nab)
- Other various minor SPC/SBC compliance fixes based upon Ronnie
Sahlberg test suite (nab)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (32 commits)
target: Set LBPWS10 bit in Logical Block Provisioning EVPD
target: Fail UNMAP when emulate_tpu=0
target: Fail WRITE_SAME w/ UNMAP=1 when emulate_tpws=0
target: Add sanity checks for DPO/FUA bit usage
target: Perform PROTECT sanity checks for WRITE_SAME
target: Fail I/O with PROTECT bit when protection is unsupported
target: Check for LBA + sectors wrap-around in sbc_parse_cdb
target: Add missing WRITE_SAME end-of-device sanity check
iscsi-target: Avoid IN_LOGOUT failure case for iser-target
target: Fix PR_APTPL_BUF_LEN buffer size limitation
iscsi-target: Drop problematic active_ts_list usage
iscsi/iser-target: Support multi-sequence sendtargets text response
iser-target: Remove duplicate function names
vhost/scsi: potential memory corruption
vhost/scsi: Global tcm_vhost -> vhost_scsi rename
vhost/scsi: Drop left-over scsi_tcq.h include
vhost/scsi: Set VIRTIO_F_ANY_LAYOUT + VIRTIO_F_VERSION_1 feature bits
vhost/scsi: Add ANY_LAYOUT support in vhost_scsi_handle_vq
vhost/scsi: Add ANY_LAYOUT iov -> sgl mapping prerequisites
vhost/scsi: Change vhost_scsi_map_to_sgl to accept iov ptr + len
...
- Re-enable on-demand paging changes with stable ABI
- Fairly large set of ocrdma HW driver fixes
- Some qib HW driver fixes
- Other miscellaneous changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABCAAGBQJU52nHAAoJEENa44ZhAt0hkycP/0vwYNl0JJadasSUrLm2AWje
iAePU+K7uiyxSuIU+eLnyyDV/iQ2sCjXfhQNE6FnFhH3JjwBYbhS2Q8WcjwfRWYX
iFhORQltb3spSeLdT7N1QfkMF4MtAw3ENPE3QKIgNaIQSso+J256BHrSiqr9Akwe
hwIVr0TLDO59ggPs3c083uUhC+5AMViMVgRR+N9+/59WHz2vG2WsTunpg1sYOAgC
KpUhfZW4za5xYJ0c8BOnPiSAfJasD1UdDg3oX0RPD4j/diiWAO6EOR+jkOLtODpd
8uhD8HM7ZvCKE1io5QnVdjTR/n51NaVGHk+yfWJRSvV1sw1AALtU4NVniI+E5mFs
Fwe+zUzbQ3j08TtrU0VjaeteBh2oGC0pJlkJS9+HXeDmH30/LQCMCiA5mBSSEPDg
0cPEAJgGAZqOIyyZe8jSslW/iN0cE6FDDb8+/1AZ80IfbdMxXh9FVwi7cdXn8+OQ
nXmtnSa7yzKWS9VVXDrvSzI0Y2oDv8DSDpCWGCm7bUcDXd/T5LpPR3RdSorGkYAr
O2zmuJZlCdkuKgW91O7cztNj2hTlDnJ+e+5P05KwPOb86Muum6tphLJd5b1h970X
Actx/6EX/ycSQ3ukiKW7Ksn2bYD3RLZvdbPYQM5xUjlGGWPF6nvmbZ8MqnyaLFfE
WKvx39DMGq3ktofiMkbf
=JLsF
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA updates from Roland Dreier:
- Re-enable on-demand paging changes with stable ABI
- Fairly large set of ocrdma HW driver fixes
- Some qib HW driver fixes
- Other miscellaneous changes
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (43 commits)
IB/qib: Add blank line after declaration
IB/qib: Fix checkpatch warnings
IB/mlx5: Enable the ODP capability query verb
IB/core: Add on demand paging caps to ib_uverbs_ex_query_device
IB/core: Add support for extended query device caps
RDMA/cxgb4: Don't hang threads forever waiting on WR replies
RDMA/ocrdma: Fix off by one in ocrdma_query_gid()
RDMA/ocrdma: Use unsigned for bit index
RDMA/ocrdma: Help gcc generate better code for ocrdma_srq_toggle_bit
RDMA/ocrdma: Update the ocrdma module version string
RDMA/ocrdma: set vlan present bit for user AH
RDMA/ocrdma: remove reference of ocrdma_dev out of ocrdma_qp structure
RDMA/ocrdma: Add support for interrupt moderation
RDMA/ocrdma: Honor return value of ocrdma_resolve_dmac
RDMA/ocrdma: Allow expansion of the SQ CQEs via buddy CQ expansion of the QP
RDMA/ocrdma: Discontinue support of RDMA-READ-WITH-INVALIDATE
RDMA/ocrdma: Host crash on destroying device resources
RDMA/ocrdma: Report correct state in ibv_query_qp
RDMA/ocrdma: Debugfs enhancments for ocrdma driver
RDMA/ocrdma: Report correct count of interrupt vectors while registering ocrdma device
...
Upstream checkpatch now requires this.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Code that does this:
if (!(d_unhashed(tmp) && tmp->d_inode)) {
...
simple_unlink(parent->d_inode, tmp);
}
is broken because:
!(d_unhashed(tmp) && tmp->d_inode)
is equivalent to:
!d_unhashed(tmp) || !tmp->d_inode
so it is possible to get into simple_unlink() with tmp->d_inode == NULL.
simple_unlink(), however, assumes tmp->d_inode cannot be NULL.
I think that what was meant is this:
!d_unhashed(tmp) && tmp->d_inode
and that the logical-not operator or the final close-bracket was misplaced.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Bryan O'Sullivan <bos@pathscale.com>
cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Re-enable the on-demand paging capability query through the
extended query device verb.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Reviewed-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add on-demand paging capabilities reporting to the extended query device verb.
Yann Droneaud writes:
Note: as offsetof() is used to retrieve the size of the lower chunk
of the response, beware that it only works if the upper chunk
is right after, without any implicit padding. And, as the size of
the latter chunk is added to the base size, implicit padding at the
end of the structure is not taken in account. Both point must be
taken in account when extending the uverbs functionalities.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Reviewed-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add extensible query device capabilities verb to allow adding new features.
ib_uverbs_ex_query_device is added and copy_query_dev_fields is used to copy
capability fields to be used by both ib_uverbs_query_device and
ib_uverbs_ex_query_device.
Following the discussion about this patch [1], the code now validates
the command's comp_mask is zero, returning -EINVAL for unknown values,
in order to allow extending the verb in the future.
The verb also checks the user-space provided response buffer size and
only fills in capabilities that will fit in the buffer. In attempt to
follow the spirit of presentation [2] by Tzahi Oved that was presented
during OpenFabrics Alliance International Developer Workshop 2013, the
comp_mask bits will only describe which fields are valid. Furthermore,
fields that can simply be cleared when they are not supported, do not
require a comp_mask bit at all. The verb returns a response_length
field containing the actual number of bytes written by the kernel, so
that a newer version running on an older kernel can tell which fields
were actually returned.
[1] [PATCH v1 0/5] IB/core: extended query device caps cleanup for v3.19
http://thread.gmane.org/gmane.linux.kernel.api/7889/
[2] https://www.openfabrics.org/images/docs/2013_Dev_Workshop/Tues_0423/2013_Workshop_Tues_0830_Tzahi_Oved-verbs_extensions_ofa_2013-tzahio.pdf
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Reviewed-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In c4iw_wait_for_reply(), if a FW6_MSG WR reply is not received after
C4IW_WR_TO seconds, fail the WR operation and mark the device as fatally
dead. Further, if the device is marked fatally dead, then fail the WR
wait immediately.
Also change the timeout to 60 seconds.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The ->sgid_tbl[] array has OCRDMA_MAX_SGID number of elements so this
test is off by one. ->sgid_tbl is allocated in ocrdma_alloc_resources().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In the expressions idx/32 and idx%32, both idx and 32 have signed
type, and unfortunately the C standard prescribes rounding to 0, so
unless gcc can prove that idx is non-negative, these cannot be
implemented as simple shift respectively mask operations. Help gcc by
changing the type of idx to unsigned - this cuts another few
instructions from the generated code.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
gcc emits a surprising amount of code in order to flip a bit. One
would think that a single instruction is enough.
$ scripts/bloat-o-meter /tmp/ocrdma_verbs.o drivers/infiniband/hw/ocrdma/ocrdma_verbs.o
add/remove: 0/0 grow/shrink: 0/3 up/down: 0/-142 (-142)
function old new delta
ocrdma_post_srq_recv 498 460 -38
ocrdma_poll_cq 2010 1962 -48
ocrdma_discard_cqes 495 439 -56
All three calls of ocrdma_srq_toggle_bit happen within spinlocks, so
saving a few useless instructions might be worthwhile.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
For the AH that describs a VLAN interface details, vlan present bit
needs to be set during posting a WQE. This patch adds the code to
allow it happening.
Signed-off-by: Mitesh Ahuja <mitesh.ahuja@emulex.com>
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add support for interrupt moderation for ocrdma device. Thresholds
for high interrupt rates are static values derived based on experimental
results.
Signed-off-by: Mitesh Ahuja <mitesh.ahuja@emulex.com>
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Check for return value for ocrdma_resolve_dmac while setting AV params.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Mitesh Ahuja <mitesh.ahuja@emulex.com>
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
If the SQ and RQ of the QP in error state uses separate CQs, traverse
the list of QPs using each CQs and invoke the buddy CQ handler for
both SQ and RQ.
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Mitesh Ahuja <mitesh.ahuja@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
1. Cleanup sequence in ocrdma_remove(). The device should be
unregistered from IB stack before any device specific cleanup.
2. Always return success in the resource destroy path. In case destroy
command returns error, IB stack will trigger cleanup again while
closing the uverbs device causing kernel panic BUG_ON().
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Mitesh Ahuja <mitesh.ahuja@emulex.com>
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Move PD allocation and deallocation from firmware to driver. At
driver load time all the PDs will be requested from firmware and their
management will be handled by driver to reduce mailbox commands
overhead at runtime.
Signed-off-by: Mitesh Ahuja <mitesh.ahuja@emulex.com>
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When the last on-demand paging MR is released the notifier count is
left non-zero so that concurrent page faults will have to abort. If a
new MR is then registered, the counter is reset. However, the decision
is made to put the new MR in the list waiting for the notifier count
to reach zero, before the counter is reset. An invalidation or another
MR registration can release the MR to handle page faults, but without
such an event the MR can wait forever.
The patch fixes this issue by adding a check whether the MR is the
first on-demand paging MR when deciding whether it is ready to handle
page faults. If it is the first MR, we know that there are no mmu
notifiers running in parallel to the registration.
Fixes: 882214e2b1 ("IB/core: Implement support for MMU notifiers regarding on demand paging regions")
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When we create an MR using reg_create, the mlx5_ib_dev pointer is not
updated on the new MR. This results in a kernel panics for ODP MRs
while handling page faults, when the mlx5_ib_update_mtt function uses
the invalid device pointer.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
If a GUID is not found, the 64-bit GUID printed in the message log
warning should converted to host-endian order for printing.
Found by Doug Ledford and Hal Rosenstock. Fix suggested by Hal.
Signed-off-by: Hal Rosenstock <hal@dev.mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
1. Before the entries alignment, we need to check that the entries
doesn't exceed the device's max cqe.
2. After the alignment, we need to make sure that the aligned number
doesn't exceed the max cqes+1. The additional cqe is used to denote
that the resizing operation has completed.
3. If the users asks to resize the CQ with entries less than the
oustanding cqes we should fail instead of returning 0.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In case handle_eth_ud_smac_index fails, we need to free the allocated resources.
Fixes: 2f5bb47368 ("mlx4: Add ref counting to port MAC table for RoCE")
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The deadlock occurs in __uverbs_modify_qp: we take a lock (idr_read_qp)
and in case of failure in ib_resolve_eth_l2_attrs we don't release
it (put_qp_read). Fix that.
Fixes: ed4c54e5b4 ("IB/core: Resolve Ethernet L2 addresses when modifying QP")
Signed-off-by: Moshe Lazer <moshel@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Pull debugfs patches from Al Viro:
"debugfs patches, mostly to make it possible for something like tracefs
to be transparently automounted on given directory in debugfs.
New primitive in there is debugfs_create_automount(name, parent, func,
arg), which creates a directory and makes its ->d_automount() return
func(arg). Another missing primitive was debugfs_create_file_size() -
open-coded in quite a few places. Dave's patch adds it and converts
the open-code instances to calling it"
* 'debugfs_automount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
debugfs: Provide a file creation function that also takes an initial size
new primitive: debugfs_create_automount()
debugfs: split end_creating() into success and failure cases
debugfs: take mode-dependent parts of debugfs_get_inode() into callers
fold debugfs_mknod() into callers
fold debugfs_create() into caller
fold debugfs_mkdir() into caller
debugfs_mknod(): get rid useless arguments
fold debugfs_link() into caller
debugfs: kill __create_file()
debugfs: split the beginning and the end of __create_file() off
debugfs_{mkdir,create,link}(): get rid of redundant argument
When marshaling a user path to the kernel struct ib_sa_path, we need
to zero smac and dmac and set the vlan id to the "no vlan" value.
This is to ensure that Ethernet attributes are not used with
InfiniBand QPs.
Fixes: dd5f03beb4 ("IB/core: Ethernet L2 attributes in verbs/cm structures")
Signed-off-by: Ilya Nelkenbaum <ilyan@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In some cases, we might reach the iser connection termination without
ep_disconnect being invoked (for example if user-space daemon doesn't
exists. In this case, we need to free the iscsi endpoint when we
remove the iser connection.
Signed-off-by: Ariel Nahum <arieln@mellanox.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When teardown process starts during live IO, we need to keep the
memory regions pool (frmr/fmr) until all in-flight tasks are properly
released, since each task may return a memory region to the pool. In
order to do this, we pass a destroy flag to iser_free_ib_conn_res to
indicate we can destroy the device and the memory regions
pool. iser_conn_release will pass it as true and also DEVICE_REMOVAL
event (we need to let the device to properly remove).
Also, Since we conditionally call iser_free_rx_descriptors,
remove the extra check on iser_conn->rx_descs.
Fixes: 5426b1711f ("IB/iser: Collapse cleanup and disconnect handlers")
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The uses of "rcu_assign_pointer()" are NULLing out the pointers.
According to RCU_INIT_POINTER()'s block comment:
"1. This use of RCU_INIT_POINTER() is NULLing out the pointer"
it is better to use it instead of rcu_assign_pointer() because it has a
smaller overhead.
The following Coccinelle semantic patch was used:
@@
@@
- rcu_assign_pointer
+ RCU_INIT_POINTER
(..., NULL)
[Derived from http://marc.info/?l=linux-rdma&m=140836519219236&w=2]
Tested-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
According to RCU_INIT_POINTER()'s block comment 3.a, it can be used if
"1. This use of RCU_INIT_POINTER() is NULLing out the pointer"
it is better to use it instead of rcu_assign_pointer() because it has a
smaller overhead.
"3. The referenced data structure has already been exposed to readers either
at compile time or via rcu_assign_pointer() -and-
a. You have not made -any- reader-visible changes to this structure since
then".
These cases fulfill the conditions above because between the
rcu_dereference_protected() call and the rcu_assign_pointer() call
there is no update of that value. Therefore, this patch makes the
replacement.
The following Coccinelle semantic patch was used:
@@
@@
- rcu_assign_pointer
+ RCU_INIT_POINTER
(...,
(
rtnl_dereference(...)
|
rcu_dereference_protected(...)
) )
[consolidated from http://marc.info/?l=linux-rdma&m=140836578119485&w=2 and
http://marc.info/?l=linux-rdma&m=140906361403047&w=2]
Tested-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Andreea-Cristina Bernat <bernat.ada@gmail.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The current code returns success when kmalloc() fails. It should
return an error code, -ENOMEM.
Fixes: e126ba97db ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Provide a file creation function that also takes an initial size so that the
caller doesn't have to set i_size, thus meaning that we don't have to call
deal with ->d_inode in the callers.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add support to recognize another board variation named QMH7360.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Vinit Agnihotri <vinit.abhay.agnihotri@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This changeset removes all the code that allows the driver to write to
the EEPROM and update the recorded error counters and power on hours.
These two stats are unused and writing them exposes a timing risk
which could leave the EEPROM in a bad state preventing further normal
operation of the HCA.
Cc: <stable@vger.kernel.org>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Mitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The MLX4_PROT_IB_IPV4 protocol should only be used with RoCEv2 and such.
Removing this wrong usage allows to run multicast applications over RoCE.
Fixes: d487ee7774 ("IB/mlx4: Use IBoE (RoCE) IP based GIDs in the port GID table")
Reported-by: Carol Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
We always unmap SGs with the same direction instead of unmapping
with the direction the mapping was done, fix that.
Fixes: 9a8b08fad2 ("IB/iser: Generalize iser_unmap_task_data and [...]")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Remove the function ipath_unordered_wc() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
A race exists where the application can be destroying the CQ concurrently
with a HW interrupt indicating a completion has been inserted into the CQ.
This can cause an event notification upcall to the application after the
CQ has been destroyed.
The solution is to serialize looking up the CQ in the IDR table and
referencing the CQ in c4iw_ev_handler() with removing the CQID from the
IDR table and blocking until the refcnt reaches 0 in c4iw_destroy_cq().
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In case sendtargets response is larger than initiator MRDSL, we
send a partial sendtargets response (setting F=0, C=1, TTT!=0xffffffff),
accept a consecutive empty text message and send the rest of the payload.
In case we are done, we set F=1, C=0, TTT=0xffffffff.
We do that by storing the sendtargets response bytes done under
the session.
This patch also makes iscsit_find_cmd_from_itt public for isert.
(Re-add cmd->maxcmdsn_inc and clear in iscsit_build_text_rsp - nab)
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull networking updates from David Miller:
1) More iov_iter conversion work from Al Viro.
[ The "crypto: switch af_alg_make_sg() to iov_iter" commit was
wrong, and this pull actually adds an extra commit on top of the
branch I'm pulling to fix that up, so that the pre-merge state is
ok. - Linus ]
2) Various optimizations to the ipv4 forwarding information base trie
lookup implementation. From Alexander Duyck.
3) Remove sock_iocb altogether, from CHristoph Hellwig.
4) Allow congestion control algorithm selection via routing metrics.
From Daniel Borkmann.
5) Make ipv4 uncached route list per-cpu, from Eric Dumazet.
6) Handle rfs hash collisions more gracefully, also from Eric Dumazet.
7) Add xmit_more support to r8169, e1000, and e1000e drivers. From
Florian Westphal.
8) Transparent Ethernet Bridging support for GRO, from Jesse Gross.
9) Add BPF packet actions to packet scheduler, from Jiri Pirko.
10) Add support for uniqu flow IDs to openvswitch, from Joe Stringer.
11) New NetCP ethernet driver, from Muralidharan Karicheri and Wingman
Kwok.
12) More sanely handle out-of-window dupacks, which can result in
serious ACK storms. From Neal Cardwell.
13) Various rhashtable bug fixes and enhancements, from Herbert Xu,
Patrick McHardy, and Thomas Graf.
14) Support xmit_more in be2net, from Sathya Perla.
15) Group Policy extensions for vxlan, from Thomas Graf.
16) Remove Checksum Offload support for vxlan, from Tom Herbert.
17) Like ipv4, support lockless transmit over ipv6 UDP sockets. From
Vlad Yasevich.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1494+1 commits)
crypto: fix af_alg_make_sg() conversion to iov_iter
ipv4: Namespecify TCP PMTU mechanism
i40e: Fix for stats init function call in Rx setup
tcp: don't include Fast Open option in SYN-ACK on pure SYN-data
openvswitch: Only set TUNNEL_VXLAN_OPT if VXLAN-GBP metadata is set
ipv6: Make __ipv6_select_ident static
ipv6: Fix fragment id assignment on LE arches.
bridge: Fix inability to add non-vlan fdb entry
net: Mellanox: Delete unnecessary checks before the function call "vunmap"
cxgb4: Add support in cxgb4 to get expansion rom version via ethtool
ethtool: rename reserved1 memeber in ethtool_drvinfo for expansion ROM version
net: dsa: Remove redundant phy_attach()
IB/mlx4: Reset flow support for IB kernel ULPs
IB/mlx4: Always use the correct port for mirrored multicast attachments
net/bonding: Fix potential bad memory access during bonding events
tipc: remove tipc_snprintf
tipc: nl compat add noop and remove legacy nl framework
tipc: convert legacy nl stats show to nl compat
tipc: convert legacy nl net id get to nl compat
tipc: convert legacy nl net id set to nl compat
...
The driver exposes interfaces that directly relate to HW state. Upon fatal
error, consumers of these interfaces (ULPs) that rely on completion of
all their posted work-request could hang, thereby introducing dependencies
in shutdown order. To prevent this from happening, we manage the
relevant resources (CQs, QPs) that are used by the device. Upon a fatal error,
we now generate simulated completions for outstanding WQEs that were not
completed at the time the HW was reset.
It includes invoking the completion event handler for all involved CQs so that
the ULPs will poll those CQs. When polled we return simulated CQEs with
IB_WC_WR_FLUSH_ERR return code enabling ULPs to clean up their resources and
not wait forever for completions upon receiving remove_one.
The above change requires an extra check in the data path to make sure that when
device is in error state, the simulated CQEs will be returned and no further
WQEs will be posted.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When attaching a QP to a multicast address in bonded mode, there was an
assumption that the port of the QP must be #1. This assumption isn't the
case under the flow which enables maximal usage of the physical ports.
Fix it by always checking the port of the original flow and create the
mirrored flow on the other port.
Fixes: c6215745b6 ('IB/mlx4: Load balance ports in port aggregation mode')
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While commit 7e36ef8205 ("IB/core: Temporarily disable
ex_query_device uverb") is correct as it makes the extended
QUERY_DEVICE uverb (which came as part of commit 5a77abf9a9
("IB/core: Add support for extended query device caps") and commit
860f10a799 ("IB/core: Add flags for on demand paging support")) not
available to userspace, it doesn't address the initial issue regarding
ib_copy_to_udata() [1][2].
Additionally, further discussions around this new uverb seems to
conclude it would require a different data structure than the one
currently described in <rdma/ib_user_verbs.h> [3].
Both of these issues require a revert of the changes, so this patch
partially reverts commit 8cdd312cfe ("IB/mlx5: Implement the ODP
capability query verb") and commit 860f10a799 ("IB/core: Add flags
for on demand paging support") and fully reverts commit 5a77abf9a9
("IB/core: Add support for extended query device caps").
[1] "Re: [PATCH v3 06/17] IB/core: Add support for extended query device caps"
http://mid.gmane.org/1418733236.2779.26.camel@opteya.com
[2] "Re: [PATCH] IB/core: Temporarily disable ex_query_device uverb"
http://mid.gmane.org/1423067503.3030.83.camel@opteya.com
[3] "RE: [PATCH v1 1/5] IB/uverbs: ex_query_device: answer must not depend on request's comp_mask"
http://mid.gmane.org/2807E5FD2F6FDA4886F6618EAC48510E0CC12C30@CRSMSX101.amr.corp.intel.com
Cc: Eli Cohen <eli@mellanox.com>
Cc: Haggai Eran <haggaie@mellanox.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The macro isert_dbg already ensures that __func__ is part of the
output, so there's no reason to duplicate the function name in the
format string itself.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Conflicts:
drivers/net/vxlan.c
drivers/vhost/net.c
include/linux/if_vlan.h
net/core/dev.c
The net/core/dev.c conflict was the overlap of one commit marking an
existing function static whilst another was adding a new function.
In the include/linux/if_vlan.h case, the type used for a local
variable was changed in 'net', whereas the function got rewritten
to fix a stacked vlan bug in 'net-next'.
In drivers/vhost/net.c, Al Viro's iov_iter conversions in 'net-next'
overlapped with an endainness fix for VHOST 1.0 in 'net'.
In drivers/net/vxlan.c, vxlan_find_vni() added a 'flags' parameter
in 'net-next' whereas in 'net' there was a bug fix to pass in the
correct network namespace pointer in calls to this function.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the mlx4 IB (RoCE) device works in link aggregation mode, it
exposes a single port to upper layers. Therefore, applications always
set '1' in port_num attribute when modifying a QP or creating an address handle.
To make sure that a node uses all available ports the mlx4 driver will
override the port_num attribute with a round robin policy.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In port aggregation mode flows for port #1 (the only port) should be mirrored
on port #2. This is because packets can arrive from either physical ports.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register the interface with the mlx4 core driver with port aggregation support
and check for port aggregation mode when the 'add' function is called.
In this mode, only one physical port is reported to the upper layer
(RoCE/IB core stack and ULPs).
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is implemented twice... get rid of one copy.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
if text message dlength is 0, don't allocate a buffer for it, pass
NULL to iscsit_process_text_cmd.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Bound workqueues might be too restrictive since they allow
only a single core per session for processing completions.
WQ_UNBOUND will allow bouncing to another CPU if the running
CPU is currently busy. Luckily, our workqueues are NUMA aware
and will first try to bounce within the same NUMA socket.
My measurements with NULL backend devices show that there is
no (noticeable) additional latency as a result of the change.
I'd expect even to gain performance when working with fast
devices that also allocate MSIX interrupt vectors.
While we're at it, make it WQ_HIGHPRI since processing
completions is really a high priority for performance.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reported-by: Moussa Ba <moussaba@micron.com>
Signed-off-by: Moussa Ba <moussaba@micron.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
- Revert IPoIB driver back to 3.18 state. We had a number of fixes go
into 3.19, but they introduced regressions. We tried to get everything
fixed up but ran out of time, so we'll try again for 3.20.
- Similarly, turn off the new "extended query port" verb. Late in the
cycle we realized the ABI is not quite right, and rather than freeze
something in a rush and make a mistake, we'll take a bit more time
and get it right in 3.20.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qi4o
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband reverts from Roland Dreier:
"Last minute InfiniBand/RDMA changes for 3.19:
- Revert IPoIB driver back to 3.18 state. We had a number of fixes
go into 3.19, but they introduced regressions. We tried to get
everything fixed up but ran out of time, so we'll try again for
3.20.
- Similarly, turn off the new "extended query port" verb. Late in
the cycle we realized the ABI is not quite right, and rather than
freeze something in a rush and make a mistake, we'll take a bit
more time and get it right in 3.20"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/core: Temporarily disable ex_query_device uverb
Revert "IPoIB: Consolidate rtnl_lock tasks in workqueue"
Revert "IPoIB: Make the carrier_on_task race aware"
Revert "IPoIB: fix MCAST_FLAG_BUSY usage"
Revert "IPoIB: fix mcast_dev_flush/mcast_restart_task race"
Revert "IPoIB: change init sequence ordering"
Revert "IPoIB: Use dedicated workqueues per interface"
Revert "IPoIB: Make ipoib_mcast_stop_thread flush the workqueue"
Revert "IPoIB: No longer use flush as a parameter"
Commit 5a77abf9a9 ("IB/core: Add support for extended query device caps")
added a new extended verb to query the capabilities of RDMA devices, but the
semantics of this verb are still under debate [1].
Don't expose this verb to userspace until the ABI is nailed down.
[1] [PATCH v1 0/5] IB/core: extended query device caps cleanup for v3.19
http://www.spinics.net/lists/linux-rdma/msg22904.html
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Reviewed-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This reverts commit afe1de664e.
The series of IPoIB bug fixes that went into 3.19-rc1 introduce
regressions, and after trying to sort things out, we decided to revert
to 3.18's IPoIB driver and get things right for 3.20.
Signed-off-by: Roland Dreier <roland@purestorage.com>
This reverts commit 67d7209e1f.
The series of IPoIB bug fixes that went into 3.19-rc1 introduce
regressions, and after trying to sort things out, we decided to revert
to 3.18's IPoIB driver and get things right for 3.20.
Signed-off-by: Roland Dreier <roland@purestorage.com>
This reverts commit 016d9fb25c.
The series of IPoIB bug fixes that went into 3.19-rc1 introduce
regressions, and after trying to sort things out, we decided to revert
to 3.18's IPoIB driver and get things right for 3.20.
Signed-off-by: Roland Dreier <roland@purestorage.com>
This reverts commit e5d1dcf1b0.
The series of IPoIB bug fixes that went into 3.19-rc1 introduce
regressions, and after trying to sort things out, we decided to revert
to 3.18's IPoIB driver and get things right for 3.20.
Signed-off-by: Roland Dreier <roland@purestorage.com>
This reverts commit 3bcce487fd.
The series of IPoIB bug fixes that went into 3.19-rc1 introduce
regressions, and after trying to sort things out, we decided to revert
to 3.18's IPoIB driver and get things right for 3.20.
Signed-off-by: Roland Dreier <roland@purestorage.com>
This reverts commit 5141861cd5.
The series of IPoIB bug fixes that went into 3.19-rc1 introduce
regressions, and after trying to sort things out, we decided to revert
to 3.18's IPoIB driver and get things right for 3.20.
Signed-off-by: Roland Dreier <roland@purestorage.com>
This reverts commit bb42a6dd02.
The series of IPoIB bug fixes that went into 3.19-rc1 introduce
regressions, and after trying to sort things out, we decided to revert
to 3.18's IPoIB driver and get things right for 3.20.
Signed-off-by: Roland Dreier <roland@purestorage.com>
This reverts commit ce347ab90e.
The series of IPoIB bug fixes that went into 3.19-rc1 introduce
regressions, and after trying to sort things out, we decided to revert
to 3.18's IPoIB driver and get things right for 3.20.
Signed-off-by: Roland Dreier <roland@purestorage.com>
isert_debug_level should be static, hence no need
to initialize it.
Reported-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Maintain a persistent memory that should survive reset flow/PCI error.
This comes as a preparation for coming series to support above flows.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes srpt_close_session() to properly use an unsigned long
for wait_for_completion_timeout()'s return value, and to update WARN_ON()
to only trigger for a zero return.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Cleanup all the MACROS that are defined in t4fw_ri_api.h and affected files
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup all the MACROS defined in t4.h and the affected files
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Except for VXLAN steering rules, all offloads should work as they were
under plain DMFS mode. Fix that by enabling all the offloads under
DMFS-A0 mode, except for VXLAN steering rules.
Fixes: d57febe1a4 "net/mlx4: Add A0 hybrid steering"
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return type of find_first_bit() is architecture specific,
on ARM it is 'unsigned int', while the asm-generic code used
on x86 and a lot of other architectures returns 'unsigned long'.
When building the mlx5 driver on ARM, we get a warning about
this:
infiniband/hw/mlx5/mem.c: In function 'mlx5_ib_cont_pages':
infiniband/hw/mlx5/mem.c:84:143: warning: comparison of distinct pointer types lacks a cast
m = min(m, find_first_bit(&tmp, sizeof(tmp)));
This patch changes the driver to use min_t to make it behave
the same way on all architectures.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleanups all other macros/register define related to
CPL messages that are defined in t4_msg.h and the affected files
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleanups all macros/register define related to connection management
CPL messages that are defined in t4_msg.h and the affected files
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleanups all SGE related macros/register defines that are
defined in t4_regs.h and the affected files.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a much shorter set of patches that were on the go but didn't make it
in to the early pull request for the merge window. It's really a set of bug
fixes plus some final cleanup work on the new tag queue API.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJUlaYEAAoJEDeqqVYsXL0MmXAH/2UUcE11p0KBHMR4cAn76xrG
9093ZT9VZ4LH/Z7PbgwIWC4YHDqVpwA1+Trj1mh8PxiZz2SopWe27O2lQMRS5VUc
MN28kbmK3L0jQj+OUez10Da6k0hU/KL8TlWT765MxFDKCaAuPZ4u541tyZEIGmLL
olOQrn/fSlu+18QqqZ+D2rMaK7kGH6ZgbOadnRfYGkLjU4YeAMEC9L7UgnDxHiaN
gZozoARkGeAnDJERVETRTtAiOXGRH8sGCpue0yYlhZXpAQ9cFUkS/hMqDWnaVC2S
0x0w34RvbxSqO0gPT0K5XLoMiFyg04vnZ2xBVFBsANQTSEjQJO8USNAa4r74hf8=
=D3eN
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI update from James Bottomley:
"This is a much shorter set of patches that were on the go but didn't
make it in to the early pull request for the merge window. It's
really a set of bug fixes plus some final cleanup work on the new tag
queue API"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
storvsc: ring buffer failures may result in I/O freeze
ipr: set scsi_level correctly for disk arrays
ipr: add support for async scanning to speed up boot
scsi_debug: fix missing "break;" in SDEBUG_UA_CAPACITY_CHANGED case
scsi_debug: take sdebug_host_list_lock when changing capacity
scsi_debug: improve driver description in Kconfig
scsi_debug: fix compare and write errors
qla2xxx: fix race in handling rport deletion during recovery causes panic
scsi: blacklist RSOC for Microsoft iSCSI target devices
scsi: fix random memory corruption with scsi-mq + T10 PI
Revert "[SCSI] mpt3sas: Remove phys on topology change"
Revert "[SCSI] mpt2sas: Remove phys on topology change."
esas2r: Correct typos of "validate" in a comment
fc: FCP_PTA_SIMPLE is 0
ibmvfc: remove unused tag variable
scsi: remove MSG_*_TAG defines
scsi: remove scsi_set_tag_type
scsi: remove scsi_get_tag_type
scsi: never drop to untagged mode during queue ramp down
scsi: remove ->change_queue_type method
Pull SCSI target fixes from Nicholas Bellinger:
"The highlights this merge window include:
- Allow target fabric drivers to function as built-in. (Roland)
- Fix tcm_loop multi-TPG endpoint nexus bug. (Hannes)
- Move per device config_item_type into se_subsystem_api, allowing
configfs attributes to be defined at module_init time. (Jerome +
nab)
- Convert existing IBLOCK/FILEIO/RAMDISK/PSCSI/TCMU drivers to use
external configfs attributes. (nab)
- A number of iser-target fixes related to active session + network
portal shutdown stability during extended stress testing. (Sagi +
Slava)
- Dynamic allocation of T10-PI contexts for iser-target, fixing a
potentially bogus iscsi_np->tpg_np pointer reference in >= v3.14
code. (Sagi)
- iser-target performance + scalability improvements. (Sagi)
- Fixes for SPC-4 Persistent Reservation AllRegistrants spec
compliance. (Ilias + James + nab)
- Avoid potential short kern_sendmsg() in iscsi-target for now until
Al's conversion to use msghdr iteration is merged post -rc1.
(Viro)
Also, Sagi has requested a number of iser-target patches (9) that
address stability issues he's encountered during extended stress
testing be considered for v3.10.y + v3.14.y code. Given the amount of
LOC involved, it will certainly require extra backporting effort.
Apologies in advance to Greg-KH & Co on this. Sagi and I will be
working post-merge to ensure they each get applied correctly"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (53 commits)
target: Allow AllRegistrants to re-RESERVE existing reservation
uapi/linux/target_core_user.h: fix headers_install.sh badness
iscsi-target: Fail connection on short sendmsg writes
iscsi-target: nullify session in failed login sequence
target: Avoid dropping AllRegistrants reservation during unregister
target: Fix R_HOLDER bit usage for AllRegistrants
iscsi-target: Drop left-over bogus iscsi_np->tpg_np
iser-target: Fix wc->wr_id cast warning
iser-target: Remove code duplication
iser-target: Adjust log levels and prettify some prints
iser-target: Use debug_level parameter to control logging level
iser-target: Fix logout sequence
iser-target: Don't wait for session commands from completion context
iser-target: Reduce CQ lock contention by batch polling
iser-target: Introduce isert_poll_budget
iser-target: Remove an atomic operation from the IO path
iser-target: Remove redundant call to isert_conn_terminate
iser-target: Use single CQ for TX and RX
iser-target: Centralize completion elements to a context
iser-target: Cast wr_id with uintptr_t instead of unsinged long
...
* Implement the relevant invalidation functions (zap MTTs as needed)
* Implement interlocking (and rollback in the page fault handlers) for
cases of a racing notifier and fault.
* With this patch we can now enable the capability bits for supporting RC
send/receive/RDMA read/RDMA write, and UD send.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch implement a page fault handler (leaving the pages pinned as
of time being). The page fault handler handles initiator and responder
page faults for UD/RC transports, for send/receive operations, as well
as RDMA read/write initiator support.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
* Refactor MR registration and cleanup, and fix reg_pages accounting.
* Create a work queue to handle page fault events in a kthread context.
* Register a fault handler to get events from the core for each QP.
The registered fault handler is empty in this patch, and only a later
patch implements it.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The new function allows updating the page tables of a memory region
after it was created. This can be used to handle page faults and page
invalidations.
Since mlx5_ib_update_mtt will need to work from within page invalidation,
so it must not block on memory allocation. It employs an atomic memory
allocation mechanism that is used as a fallback when kmalloc(GFP_ATOMIC) fails.
In order to reuse code from mlx5_ib_populate_pas, the patch splits
this function and add the needed parameters.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This patch wraps together several changes needed for on-demand paging support
in the mlx5_ib_populate_pas function, and when registering memory regions.
* Instead of accepting a UMR bit telling the function to enable all
access flags, the function now accepts the access flags themselves.
* For on-demand paging memory regions, fill the memory tables from the
correct list, and enable/disable the access flags per-page according
to whether the page is present.
* A new bit is set to enable writing of access flags when using the
firmware create_mkey command.
* Disable contig pages when on-demand paging is enabled.
In addition the patch changes the UMR code to use PTR_ALIGN instead of
our own macro.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The patch adds infrastructure to query ODP capabilities in the mlx5
driver. The code will read the capabilities from the device, and
enable only those capabilities that both the driver and the device
supports. At this point ODP is not supported, so no capability is
copied from the device, but the patch exposes the global ODP device
capability bit.
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In case the last argument of the connection string is processed as a
string (destination GID for example).
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Acked-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
* Add an interval tree implementation for ODP umems. Create an
interval tree for each ucontext (including a count of the number of
ODP MRs in this context, semaphore, etc.), and register ODP umems in
the interval tree.
* Add MMU notifiers handling functions, using the interval tree to
notify only the relevant umems and underlying MRs.
* Register to receive MMU notifier events from the MM subsystem upon
ODP MR registration (and unregister accordingly).
* Add a completion object to synchronize the destruction of ODP umems.
* Add mechanism to abort page faults when there's a concurrent invalidation.
The way we synchronize between concurrent invalidations and page
faults is by keeping a counter of currently running invalidations, and
a sequence number that is incremented whenever an invalidation is
caught. The page fault code checks the counter and also verifies that
the sequence number hasn't progressed before it updates the umem's
page tables. This is similar to what the kvm module does.
In order to prevent the case where we register a umem in the middle of
an ongoing notifier, we also keep a per ucontext counter of the total
number of active mmu notifiers. We only enable new umems when all the
running notifiers complete.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Yuval Dagan <yuvalda@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
* Extend the umem struct to keep the ODP related data.
* Allocate and initialize the ODP related information in the umem
(page_list, dma_list) and freeing as needed in the end of the run.
* Store a reference to the process PID struct in the ucontext. Used to
safely obtain the task_struct and the mm during fault handling,
without preventing the task destruction if needed.
* Add 2 helper functions: ib_umem_odp_map_dma_pages and
ib_umem_odp_unmap_dma_pages. These functions get the DMA addresses
of specific pages of the umem (and, currently, pin them).
* Support for page faults only - IB core will keep the reference on
the pages used and call put_page when freeing an ODP umem
area. Invalidations support will be added in a later patch.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
* Add a configuration option for enable on-demand paging support in
the infiniband subsystem (CONFIG_INFINIBAND_ON_DEMAND_PAGING). In a
later patch, this configuration option will select the MMU_NOTIFIER
configuration option to enable mmu notifiers.
* Add a flag for on demand paging (ODP) support in the IB device capabilities.
* Add a flag to request ODP MR in the access flags to reg_mr.
* Fail registrations done with the ODP flag when the low-level driver
doesn't support this.
* Change the conditions in which an MR will be writable to explicitly
specify the access flags. This is to avoid making an MR writable just
because it is an ODP MR.
* Add a ODP capabilities to the extended query device verb.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add extensible query device capabilities verb to allow adding new features.
ib_uverbs_ex_query_device is added and copy_query_dev_fields is used to
copy capability fields to be used by both ib_uverbs_query_device and
ib_uverbs_ex_query_device.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add a helper function mlx5_ib_read_user_wqe to read information from
user-space owned work queues. The function will be used in a later
patch by the page-fault handling code in mlx5_ib.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
[ Add stub for ib_umem_copy_from() for CONFIG_INFINIBAND_USER_MEM=n
- Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
In some drivers there's a need to read data from a user space area
that was pinned using ib_umem when running from a different process
context.
The ib_umem_copy_from function allows reading data from the physical
pages pinned in the ib_umem struct.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In order to allow umems that do not pin memory, we need the umem to
keep track of its region's address.
This makes the offset field redundant, and so this patch removes it.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The current UMR interface doesn't allow partial updates to a memory
region's page tables. This patch changes the interface to allow that.
It also changes the way the UMR operation validates the memory
region's state. When set, IB_SEND_UMR_FAIL_IF_FREE will cause the UMR
operation to fail if the MKEY is in the free state. When it is
unchecked the operation will check that it isn't in the free state.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Since UMR code now uses its own context struct on the stack, the pas
and dma pointers for the UMR operation that remained in the mlx5_ib_mr
struct are not necessary. This patch removes them.
Fixes: a74d24168d ("IB/mlx5: Refactor UMR to have its own context struct")
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
For user applications that use UD QPs, always resolve destination MAC
from the GRH. This is to avoid failure due to any garbage value in
the attr->dmac.
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This error was detected by sparse static checker:
drivers/infiniband/hw/mlx4/mr.c:226:21: warning: symbol 'err' shadows an earlier one
drivers/infiniband/hw/mlx4/mr.c:197:13: originally declared here
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Following few recent Block integrity updates, we align the iSER data
integrity offload settings with:
- Deprecate pi_guard module param
- Expose support for DIX type 0.
- Use scsi_transfer_length for the transfer length
- Get pi_interval, ref_tag, ref_remap, bg_type and
check_mask setting from scsi_cmnd
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Use likely() for wc.status == IB_WC_SUCCESS
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
And fix a checkpatch warning.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
No reason to settle with four, can use the min between device max comp
vectors and number of cores.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
It is enough to check mem_h pointer assignment, mem_h == NULL will
indicate that buffer is not registered using mr.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When closing the connection, we should first terminate the connection
(in case it was not previously terminated) to guarantee the QP is in
error state and we are done with servicing IO. Only then go ahead with
tasks cleanup via iscsi_conn_stop.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In certain scenarios (target kill with live IO) scsi TMFs may race
with iser RDMA teardown, which might cause NULL dereference on iser IB
device handle (which might have been freed). In this case we take a
conditional lock for TMFs and check the connection state (avoid
introducing lock contention in the IO path). This is indeed best
effort approach, but sufficient to survive multi targets sudden death
while heavy IO is inflight.
While we are on it, add a nice kernel-doc style documentation.
Reported-by: Ariel Nahum <arieln@mellanox.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
If rdma_cm error event comes after ep_poll but before conn_bind, we
should protect against dereferncing the device (which may have been
terminated) in session_create and conn_create (already protected)
callbacks.
Signed-off-by: Ariel Nahum <arieln@mellanox.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Use uintptr_t to handle wr_id casting, which was found by Kbuild test
robot and smatch. Also remove an internal definition of variable which
potentially shadows an external one (and make sparse happy).
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix a regression was introduced in commit 6df5a128f0 ("IB/iser:
Suppress scsi command send completions").
The sig_count was wrongly set to be static variable, thus it is
possible that we won't reach to (sig_count % ISER_SIGNAL_BATCH) == 0
condition (due to races) and the send queue will be overflowed.
Instead keep sig_count per connection. We don't need it to be atomic
as we are safe under the iscsi session frwd_lock taken by libiscsi on
the queuecommand path.
Fixes: 6df5a128f0 ("IB/iser: Suppress scsi command send completions")
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When creating a connection QP we choose the least used CQ and inc the
number of active QPs on that. If we fail to create the QP, we need to
decrement the active QPs counter.
Reported-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
No real need to wait for TIMEWAIT_EXIT before we destroy the RDMA
resources (also TIMEAWAIT_EXIT is not guarenteed to always arrive). As
for the cma_id, only destroy it if the state is not DOWN where in this
case, conn_release is already running and we don't want to compete.
Signed-off-by: Ariel Nahum <arieln@mellanox.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In case of the HCA going into catasrophic error flow, the
beacon post_send is likely to fail, so surely there will
be no completion for it.
In this case, use a best effort approach and don't wait for beacon
completion if we failed to post the send.
Reported-by: Alex Tabachnik <alext@mellanox.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Re-adjust max CQEs per CQ and max send_wr per QP according
to the resource limits supported by underlying hardware.
Signed-off-by: Minh Tran <minhduc.tran@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Acked-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Various places in the IPoIB code had a deadlock related to flushing
the ipoib workqueue. Now that we have per device workqueues and a
specific flush workqueue, there is no longer a deadlock issue with
flushing the device specific workqueues and we can do so unilaterally.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
We used to pass a flush variable to mcast_stop_thread to indicate if
we should flush the workqueue or not. This was due to some code
trying to flush a workqueue that it was currently running on which is
a no-no. Now that we have per-device work queues, and now that
ipoib_mcast_restart_task has taken the fact that it is queued on a
single thread workqueue with all of the ipoib_mcast_join_task's and
therefore has no need to stop the join task while it runs, we can do
away with the flush parameter and unilaterally flush always.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
During my recent work on the rtnl lock deadlock in the IPoIB driver, I
saw that even once I fixed the apparent races for a single device, as
soon as that device had any children, new races popped up. It turns
out that this is because no matter how well we protect against races
on a single device, the fact that all devices use the same workqueue,
and flush_workqueue() flushes *everything* from that workqueue, we can
have one device in the middle of a down and holding the rtnl lock and
another totally unrelated device needing to run mcast_restart_task,
which wants the rtnl lock and will loop trying to take it unless is
sees its own FLAG_ADMIN_UP flag go away. Because the unrelated
interface will never see its own ADMIN_UP flag drop, the interface
going down will deadlock trying to flush the queue. There are several
possible solutions to this problem:
Make carrier_on_task and mcast_restart_task try to take the rtnl for
some set period of time and if they fail, then bail. This runs the
real risk of dropping work on the floor, which can end up being its
own separate kind of deadlock.
Set some global flag in the driver that says some device is in the
middle of going down, letting all tasks know to bail. Again, this can
drop work on the floor. I suppose if our own ADMIN_UP flag doesn't go
away, then maybe after a few tries on the rtnl lock we can queue our
own task back up as a delayed work and return and avoid dropping work
on the floor that way. But I'm not 100% convinced that we won't cause
other problems.
Or the method this patch attempts to use, which is when we bring an
interface up, create a workqueue specifically for that interface, so
that when we take it back down, we are flushing only those tasks
associated with our interface. In addition, keep the global
workqueue, but now limit it to only flush tasks. In this way, the
flush tasks can always flush the device specific work queues without
having deadlock issues.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In preparation for using per device work queues, we need to move the
start of the neighbor thread task to after ipoib_ib_dev_init and move
the destruction of the neighbor task to before ipoib_ib_dev_cleanup.
Otherwise we will end up freeing our workqueue with work possibly
still on it.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Our mcast_dev_flush routine and our mcast_restart_task can race
against each other. In particular, they both hold the priv->lock
while manipulating the rbtree and while removing mcast entries from
the multicast_list and while adding entries to the remove_list, but
they also both drop their locks prior to doing the actual removes.
The mcast_dev_flush routine is run entirely under the rtnl lock and so
has at least some locking. The actual race condition is like this:
Thread 1 Thread 2
ifconfig ib0 up
start multicast join for broadcast
multicast join completes for broadcast
start to add more multicast joins
call mcast_restart_task to add new entries
ifconfig ib0 down
mcast_dev_flush
mcast_leave(mcast A)
mcast_leave(mcast A)
As mcast_leave calls ib_sa_multicast_leave, and as member in
core/multicast.c is ref counted, we run into an unbalanced refcount
issue. To avoid stomping on each others removes, take the rtnl lock
specifically when we are deleting the entries from the remove list.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit a9c8ba5884 ("IPoIB: Fix usage of uninitialized multicast
objects") added a new flag MCAST_JOIN_STARTED, but was not very strict
in how it was used. We didn't always initialize the completion struct
before we set the flag, and we didn't always call complete on the
completion struct from all paths that complete it. This made it less
than totally effective, and certainly made its use confusing. And in
the flush function we would use the presence of this flag to signal
that we should wait on the completion struct, but we never cleared
this flag, ever. This is further muddied by the fact that we overload
the MCAST_FLAG_BUSY flag to mean two different things: we have a join
in flight, and we have succeeded in getting an ib_sa_join_multicast.
In order to make things clearer and aid in resolving the rtnl deadlock
bug I've been chasing, I cleaned this up a bit.
1) Remove the MCAST_JOIN_STARTED flag entirely
2) Un-overload MCAST_FLAG_BUSY so it now only means a join is in-flight
3) Test on mcast->mc directly to see if we have completed
ib_sa_join_multicast (using IS_ERR_OR_NULL)
4) Make sure that before setting MCAST_FLAG_BUSY we always initialize
the mcast->done completion struct
5) Make sure that before calling complete(&mcast->done), we always clear
the MCAST_FLAG_BUSY bit
6) Take the mcast_mutex before we call ib_sa_multicast_join and also
take the mutex in our join callback. This forces
ib_sa_multicast_join to return and set mcast->mc before we process
the callback. This way, our callback can safely clear mcast->mc
if there is an error on the join and we will do the right thing as
a result in mcast_dev_flush.
7) Because we need the mutex to synchronize mcast->mc, we can no
longer call mcast_sendonly_join directly from mcast_send and
instead must add sendonly join processing to the mcast_join_task
A number of different races are resolved with these changes. These
races existed with the old MCAST_FLAG_BUSY usage, the
MCAST_JOIN_STARTED flag was an attempt to address them, and while it
helped, a determined effort could still trip things up.
One race looks something like this:
Thread 1 Thread 2
ib_sa_join_multicast (as part of running restart mcast task)
alloc member
call callback
ifconfig ib0 down
wait_for_completion
callback call completes
wait_for_completion in
mcast_dev_flush completes
mcast->mc is PTR_ERR_OR_NULL
so we skip ib_sa_leave_multicast
return from callback
return from ib_sa_join_multicast
set mcast->mc = return from ib_sa_multicast
We now have a permanently unbalanced join/leave issue that trips up the
refcounting in core/multicast.c
Another like this:
Thread 1 Thread 2 Thread 3
ib_sa_multicast_join
ifconfig ib0 down
priv->broadcast = NULL
join_complete
wait_for_completion
mcast->mc is not yet set, so don't clear
return from ib_sa_join_multicast and set mcast->mc
complete
return -EAGAIN (making mcast->mc invalid)
call ib_sa_multicast_leave
on invalid mcast->mc, hang
forever
By holding the mutex around ib_sa_multicast_join and taking the mutex
early in the callback, we force mcast->mc to be valid at the time we
run the callback. This allows us to clear mcast->mc if there is an
error and the join is going to fail. We do this before we complete
the mcast. In this way, mcast_dev_flush always sees consistent state
in regards to mcast->mc membership at the time that the
wait_for_completion() returns.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
We blindly assume that we can just take the rtnl lock and that will
prevent races with downing this interface. Unfortunately, that's not
the case. In ipoib_mcast_stop_thread() we will call flush_workqueue()
in an attempt to clear out all remaining instances of ipoib_join_task.
But, since this task is put on the same workqueue as the join task,
the flush_workqueue waits on this thread too. But this thread is
deadlocked on the rtnl lock. The better thing here is to use trylock
and loop on that until we either get the lock or we see that
FLAG_ADMIN_UP has been cleared, in which case we don't need to do
anything anyway and we just return.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Setting the MTU can safely be moved to the carrier_on_task, which keeps
us from needing to take the rtnl lock in the join_finish section.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
cxgb4_create_server() and cxgb4_create_server6() return NET_XMIT_*
values or a negative errno. iw_cxgb4 need to handle this correctly.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When transitioning into ERROR state, the QP was getting flushed after
waking up any waiters. This can cause applications to miss flushed work
requests which can stall an NFS mount.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
T4/T5 hardware can't handle MRs >= 8GB due to a hardware bug. So limit
registrations to < 8GB for thse devices.
Based on original work by Steve Wise <swise@opengridcomputing.com>.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
0B MRs need some tweaks to work correctly with HW. When writing the
TPTE, if the MR length is zero we now:
1) turn off all permissions
2) set the length to -1
While functionality/capabilities of the MR are the same with these
changes, it resolves a dapltest 0B RDMA Read test failure. Based on
original work by Steve Wise <swise@opengridcomputing.com>.
Signed-off-by: Pramod Kumar <pramod@chelsio.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Address resolution always does a context switch to a work-queue to
deliver the address resolution event. When the IP address is already
cached in the system ARP table, we're going through the following:
chain:
rdma_resolve_ip --> addr_resolve (cache hit) -->
which ends up with:
queue_req --> set_timeout (now) --> mod_delayed_work(,, delay=1)
We actually do realize that the timeout should be zero, but the code
forces it to a minimum of one jiffie.
Using one jiffie as the minimum delay value results in sub-optimal
scheduling of executing this work item by the workqueue, which on the
below testbed costs about 3-4ms out of 12ms total time.
To fix that, we let the minimum delay to be zero. Note that the
connect step times change too, as there are address resolution calls
from that flow.
The results were taken from running both client and server on the
same node, over mlx4 RoCE port.
before -->
step total ms max ms min us us / conn
create id : 0.01 0.01 6.00 6.00
resolve addr : 4.02 4.01 4013.00 4016.00
resolve route: 0.18 0.18 182.00 183.00
create qp : 1.15 1.15 1150.00 1150.00
connect : 6.73 6.73 6730.00 6731.00
disconnect : 0.55 0.55 549.00 550.00
destroy : 0.01 0.01 9.00 9.00
after -->
step total ms max ms min us us / conn
create id : 0.01 0.01 6.00 6.00
resolve addr : 0.05 0.05 49.00 52.00
resolve route: 0.21 0.21 207.00 208.00
create qp : 1.10 1.10 1104.00 1104.00
connect : 1.22 1.22 1220.00 1221.00
disconnect : 0.71 0.71 713.00 713.00
destroy : 0.01 0.01 9.00 9.00
Signed-off-by: Or Kehati <ork@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Applications can request that the SM assign an MGID by passing a mcast
member request containing MGID = 0. When the SM responds by sending
the allocated MGID, this MGID replaces the 0-MGID in the multicast group.
However, the MGID field in the group is also the key field in the IB
core multicast code rbtree containing the multicast groups for the
port.
Since this is a key field, correct handling requires that the group
entry be deleted from the rbtree and then re-inserted with the new
key, so that the table structure is properly maintained.
The current code does not do this correctly. Correct operation
requires that if the key-field gid has changed at all, it should be
deleted and re-inserted.
Note that when inserting, if the new MGID is zero (not the case here
but the code should handle this correctly), we allow duplicate entries
for 0-MGIDs.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
For RoCE, resolution of layer 2 address attributes forces no VLAN if
link-local GIDs are used. This patch allows applications to choose
the VLAN ID for link-local based RoCE GIDs by setting IB_QP_VID in
their QP attribute mask, and prevents the core from overriding this
choice.
Cc: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
CC [M] drivers/infiniband/ulp/isert/ib_isert.o
drivers/infiniband/ulp/isert/ib_isert.c: In function ‘isert_cq_comp_err’:
drivers/infiniband/ulp/isert/ib_isert.c:1979:42: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
- Fall-through in switch case instead in do_control_comp.
- Move rkey invalidation to a function.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
debug_level 1 (warn): Include warning messages.
debug_level 2 (info): Include relevant info for control plane.
debug_level 3 (debug): Include relevant info in the IO path.
Also, added/removed some logging messages.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Personal preference, easier control of the log level with
a single modparam which can be changed dynamically. Allows
better saparation of control and IO plains.
Replaced throughout ib_isert.c:
s/pr_debug/isert_dbg/g
s/pr_info/isert_info/g
s/pr_warn/isert_warn/g
s/pr_err/isert_err/g
Plus nit checkpatch warning change.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We don't want to wait for conn_logout_comp from isert_comp_wq
context as this blocks further completions from being processed.
Instead we wait for it conditionally (if logout response was
actually posted) in wait_conn. This wait should normally happen
immediately as it occurs after we consumed all the completions
(including flush errors) and conn_logout_comp should have been
completed.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Might result in a deadlock where completion context waits for
session commands release where the later might need a final
completion for it.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In order to reduce the contention on CQ locking (present
in some LLDDs) we poll in batches of 16 work completion items.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In case the CQ is packed with completions, we can't just
hog the CPU forever. Poll until a sufficient budget (currently
hard-coded to 64k completions) and if budget is exhausted, bailout
and give a chance to other threads.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In order to know that we consumed all the connection completions
we maintain atomic post_send_buf_count for each IO post send. But
we can know that if we post a "beacon" (zero length RECV work request)
after we move the QP into error state and the target does not serve
any new IO. When we consume it, we know we finished all the connection
completion and we can go ahead and destroy stuff.
In error completion handler we now just need to check for ISERT_BEACON_WRID
to arrive and then wait for session commands to cleanup and complete
conn_wait_comp_err.
We reserve another CQ and QP entries to fit the zero length post recv.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We are calling session reinstatement, wait_conn will start
connection termination.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Using TX and RX CQs attached to the same vector might
create a throttling effect coming from the serial processing
of a work-queue. Use one CQ instead, it will do better in interrupt
processing and it provides a simpler code. Also, We get rid of
redundant isert_rx_wq.
Next we can remove the atomic post_send_buf_count from the IO path.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
A pre-step before going to a single CQ.
Also this makes the code a little more simple to
read.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Nit, uintptr_t is designed for pointer casting, use it.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
As a pre-step to a single CQ, we unite the error completion
handlers to a single handler.
This patch does not change any functionality.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
It is disabled at the moment, we will get that back
in once the target is more stable.
This reverts commit 95b60f0
"Add support for completion interrupt coalescing"
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Currently we have no way to tell that the target stack is in shutdown
sequence. In case we have open connections, the initiator immediately
attempts to reconnect in a DDOS attack style, so we may end up
terminating the iser enabled network portal while it's np_accept_list
still have pending connections.
The workaround is simply release all the connections in the list.
A proper fix will be to start shutdown sequence by shutting the
network portal to avoid initiator immediate reconnect attempts.
But the temporary work around seems to work at this point, so I think
we can do this for now...
Reported-by: Slava Shwartsman <valyushash@gmail.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
iSER will report supported protection operations based on
the tpg attribute t10_pi settings and HCA PI offload capabilities.
If the HCA does not support PI offload or tpg attribute t10_pi is
not set, we fall to SW PI mode.
In order to do that, we move iscsit_get_sup_prot_ops after connection
tpg assignment.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fallback to software mode DIF if HCA does not support
PI (without crashing obviously). It is still possible to
run with backend protection and an unprotected frontend,
so looking at the command prot_op is not enough. Check
device PI capability on a per-IO basis (isert_prot_cmd
inline static) to determine if we need to handle protection
information.
Trace:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
IP: [<ffffffffa037f8b1>] isert_reg_sig_mr+0x351/0x3b0 [ib_isert]
Call Trace:
[<ffffffff812b003a>] ? swiotlb_map_sg_attrs+0x7a/0x130
[<ffffffffa038184d>] isert_reg_rdma+0x2fd/0x370 [ib_isert]
[<ffffffff8108f2ec>] ? idle_balance+0x6c/0x2c0
[<ffffffffa0382b68>] isert_put_datain+0x68/0x210 [ib_isert]
[<ffffffffa02acf5b>] lio_queue_data_in+0x2b/0x30 [iscsi_target_mod]
[<ffffffffa02306eb>] target_complete_ok_work+0x21b/0x310 [target_core_mod]
[<ffffffff8106ece2>] process_one_work+0x182/0x3b0
[<ffffffff8106fda0>] worker_thread+0x120/0x3c0
[<ffffffff8106fc80>] ? maybe_create_worker+0x190/0x190
[<ffffffff8107594e>] kthread+0xce/0xf0
[<ffffffff81075880>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff8159a22c>] ret_from_fork+0x7c/0xb0
[<ffffffff81075880>] ? kthread_freezable_should_stop+0x70/0x70
Reported-by: Slava Shwartsman <valyushash@gmail.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts to allocate PI contexts dynamically in order
avoid a potentially bogus np->tpg_np and associated NULL pointer
dereference in isert_connect_request() during iser-target endpoint
shutdown with multiple network portals.
Also, there is really no need to allocate these at connection
establishment since it is not guaranteed that all the IOs on
that connection will be to a PI formatted device.
We can do it in a lazy fashion so the initial burst will have a
transient slow down, but very fast all IOs will allocate a PI
context.
Squashed:
iser-target: Centralize PI context handling code
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In situations such as bond failover, The new session establishment
implicitly invokes the termination of the old connection.
So, we don't want to wait for the old connection wait_conn to completely
terminate before we accept the new connection and post a login response.
The solution is to deffer the comp_wait completion and the conn_put to
a work so wait_conn will effectively be non-blocking (flush errors are
assumed to come very fast).
We allocate isert_release_wq with WQ_UNBOUND and WQ_UNBOUND_MAX_ACTIVE
to spread the concurrency of release works.
Reported-by: Slava Shwartsman <valyushash@gmail.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The np listener cm_id will also get ADDR_CHANGE event
upcall (in case it is bound to a specific IP). Handle
it correctly by creating a new cm_id and implicitly
destroy the old one.
Since this is the second event a listener np cm_id may
encounter, we move the np cm_id event handling to a
routine.
Squashed:
iser-target: Move cma_id setup to a function
Reported-by: Slava Shwartsman <valyushash@gmail.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Take isert_conn pointer from cm_id->qp->qp_context. This
will allow us to know that the cm_id context is always
the network portal. This will make the cm_id event check
(connection or network portal) more reliable.
In order to avoid a NULL dereference in cma_id->qp->qp_context
we destroy the qp after we destroy the cm_id (and make the
dereference safe). session stablishment/teardown sequences
can happen in parallel, we should take into account that
connected_handler might race with connection teardown flow.
Also, protect isert_conn->conn_device->active_qps decrement
within the error patch during QP creation failure and the
normal teardown path in isert_connect_release().
Squashed:
iser-target: Decrement completion context active_qps in error flow
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
There is no point in accepting a new CM request only
when we are completely done with the last iscsi login.
Instead we accept immediately, this will also cause the
CM connection to reach connected state and the initiator
is allowed to send the first login. We mark that we got
the initial login and let iscsi layer pick it up when it
gets there.
This reduces the parallel login sequence by a factor of
more then 4 (and more for multi-login) and also prevents
the initiator (who does all logins in parallel) from
giving up on login timeout expiration.
In order to support multiple login requests sequence (CHAP)
we call isert_rx_login_req from isert_rx_completion insead
of letting isert_get_login_rx call it.
Squashed:
iser-target: Use kref_get_unless_zero in connected_handler
iser-target: Acquire conn_mutex when changing connection state
iser-target: Reject connect request in failure path
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
ISER_CONN_UP state is not sufficient to know if
we should wait for completion of flush errors and
disconnected_handler event.
Instead, split it to 2 states:
- ISER_CONN_UP: Got to CM connected phase, This state
indicates that we need to wait for a CM disconnect
event before going to teardown.
- ISER_CONN_FULL_FEATURE: Got to full feature phase
after we posted login response, This state indicates
that we posted recv buffers and we need to wait for
flush completions before going to teardown.
Also avoid deffering disconnected handler to a work,
and handle it within disconnected handler.
More work here is needed to handle DEVICE_REMOVAL event
correctly (cleanup all resources).
Squashed:
iser-target: Don't deffer disconnected handler to a work
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Since commit 0fc4ea701f ("Target/iser: Don't put isert_conn inside
disconnected handler") we put the conn kref in isert_wait_conn, so we
need .wait_conn to be invoked also in the error path.
Introduce call to isert_conn_terminate (called under lock)
which transitions the connection state to TERMINATING and calls
rdma_disconnect. If the state is already teminating, just bail
out back (temination started).
Also, make sure to destroy the connection when getting a connect
error event if didn't get to connected (state UP). Same for the
handling of REJECTED and UNREACHABLE cma events.
Squashed:
iscsi-target: Add call to wait_conn in establishment error flow
Reported-by: Slava Shwartsman <valyushash@gmail.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull networking updates from David Miller:
1) New offloading infrastructure and example 'rocker' driver for
offloading of switching and routing to hardware.
This work was done by a large group of dedicated individuals, not
limited to: Scott Feldman, Jiri Pirko, Thomas Graf, John Fastabend,
Jamal Hadi Salim, Andy Gospodarek, Florian Fainelli, Roopa Prabhu
2) Start making the networking operate on IOV iterators instead of
modifying iov objects in-situ during transfers. Thanks to Al Viro
and Herbert Xu.
3) A set of new netlink interfaces for the TIPC stack, from Richard
Alpe.
4) Remove unnecessary looping during ipv6 routing lookups, from Martin
KaFai Lau.
5) Add PAUSE frame generation support to gianfar driver, from Matei
Pavaluca.
6) Allow for larger reordering levels in TCP, which are easily
achievable in the real world right now, from Eric Dumazet.
7) Add a variable of napi_schedule that doesn't need to disable cpu
interrupts, from Eric Dumazet.
8) Use a doubly linked list to optimize neigh_parms_release(), from
Nicolas Dichtel.
9) Various enhancements to the kernel BPF verifier, and allow eBPF
programs to actually be attached to sockets. From Alexei
Starovoitov.
10) Support TSO/LSO in sunvnet driver, from David L Stevens.
11) Allow controlling ECN usage via routing metrics, from Florian
Westphal.
12) Remote checksum offload, from Tom Herbert.
13) Add split-header receive, BQL, and xmit_more support to amd-xgbe
driver, from Thomas Lendacky.
14) Add MPLS support to openvswitch, from Simon Horman.
15) Support wildcard tunnel endpoints in ipv6 tunnels, from Steffen
Klassert.
16) Do gro flushes on a per-device basis using a timer, from Eric
Dumazet. This tries to resolve the conflicting goals between the
desired handling of bulk vs. RPC-like traffic.
17) Allow userspace to ask for the CPU upon what a packet was
received/steered, via SO_INCOMING_CPU. From Eric Dumazet.
18) Limit GSO packets to half the current congestion window, from Eric
Dumazet.
19) Add a generic helper so that all drivers set their RSS keys in a
consistent way, from Eric Dumazet.
20) Add xmit_more support to enic driver, from Govindarajulu
Varadarajan.
21) Add VLAN packet scheduler action, from Jiri Pirko.
22) Support configurable RSS hash functions via ethtool, from Eyal
Perry.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1820 commits)
Fix race condition between vxlan_sock_add and vxlan_sock_release
net/macb: fix compilation warning for print_hex_dump() called with skb->mac_header
net/mlx4: Add support for A0 steering
net/mlx4: Refactor QUERY_PORT
net/mlx4_core: Add explicit error message when rule doesn't meet configuration
net/mlx4: Add A0 hybrid steering
net/mlx4: Add mlx4_bitmap zone allocator
net/mlx4: Add a check if there are too many reserved QPs
net/mlx4: Change QP allocation scheme
net/mlx4_core: Use tasklet for user-space CQ completion events
net/mlx4_core: Mask out host side virtualization features for guests
net/mlx4_en: Set csum level for encapsulated packets
be2net: Export tunnel offloads only when a VxLAN tunnel is created
gianfar: Fix dma check map error when DMA_API_DEBUG is enabled
cxgb4/csiostor: Don't use MASTER_MUST for fw_hello call
net: fec: only enable mdio interrupt before phy device link up
net: fec: clear all interrupt events to support i.MX6SX
net: fec: reset fep link status in suspend function
net: sock: fix access via invalid file descriptor
net: introduce helper macro for_each_cmsghdr
...
A0 hybrid steering is a form of high performance flow steering.
By using this mode, mlx4 cards use a fast limited table based steering,
in order to enable fast steering of unicast packets to a QP.
In order to implement A0 hybrid steering we allocate resources
from different zones:
(1) General range
(2) Special MAC-assigned QPs [RSS, Raw-Ethernet] each has its own region.
When we create a rss QP or a raw ethernet (A0 steerable and BF ready) QP,
we try hard to allocate the QP from range (2). Otherwise, we try hard not
to allocate from this range. However, when the system is pushed to its
limits and one needs every resource, the allocator uses every region it can.
Meaning, when we run out of raw-eth qps, the allocator allocates from the
general range (and the special-A0 area is no longer active). If we run out
of RSS qps, the mechanism tries to allocate from the raw-eth QP zone. If that
is also exhausted, the allocator will allocate from the general range
(and the A0 region is no longer active).
Note that if a raw-eth qp is allocated from the general range, it attempts
to allocate the range such that bits 6 and 7 (blueflame bits) in the
QP number are not set.
When the feature is used in SRIOV, the VF has to notify the PF what
kind of QP attributes it needs. In order to do that, along with the
"Eth QP blueflame" bit, we reserve a new "A0 steerable QP". According
to the combination of these bits, the PF tries to allocate a suitable QP.
In order to maintain backward compatibility (with older PFs), the PF
notifies which QP attributes it supports via QUERY_FUNC_CAP command.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using BF (Blue-Flame), the QPN overrides the VLAN, CV, and SV fields
in the WQE. Thus, BF may only be used for QPNs with bits 6,7 unset.
The current Ethernet driver code reserves a Tx QP range with 256b alignment.
This is wrong because if there are more than 64 Tx QPs in use,
QPNs >= base + 65 will have bits 6/7 set.
This problem is not specific for the Ethernet driver, any entity that
tries to reserve more than 64 BF-enabled QPs should fail. Also, using
ranges is not necessary here and is wasteful.
The new mechanism introduced here will support reservation for
"Eth QPs eligible for BF" for all drivers: bare-metal, multi-PF, and VFs
(when hypervisors support WC in VMs). The flow we use is:
1. In mlx4_en, allocate Tx QPs one by one instead of a range allocation,
and request "BF enabled QPs" if BF is supported for the function
2. In the ALLOC_RES FW command, change param1 to:
a. param1[23:0] - number of QPs
b. param1[31-24] - flags controlling QPs reservation
Bit 31 refers to Eth blueflame supported QPs. Those QPs must have
bits 6 and 7 unset in order to be used in Ethernet.
Bits 24-30 of the flags are currently reserved.
When a function tries to allocate a QP, it states the required attributes
for this QP. Those attributes are considered "best-effort". If an attribute,
such as Ethernet BF enabled QP, is a must-have attribute, the function has
to check that attribute is supported before trying to do the allocation.
In a lower layer of the code, mlx4_qp_reserve_range masks out the bits
which are unsupported. If SRIOV is used, the PF validates those attributes
and masks out unsupported attributes as well. In order to notify VFs which
attributes are supported, the VF uses QUERY_FUNC_CAP command. This command's
mailbox is filled by the PF, which notifies which QP allocation attributes
it supports.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, we've fired all our completion callbacks straight from our ISR.
Some of those callbacks were lightweight (for example, mlx4_en's and
IPoIB napi callbacks), but some of them did more work (for example,
the user-space RDMA stack uverbs' completion handler). Besides that,
doing more than the minimal work in ISR is generally considered wrong,
it could even lead to a hard lockup of the system. Since when a lot
of completion events are generated by the hardware, the loop over those
events could be so long, that we'll get into a hard lockup by the system
watchdog.
In order to avoid that, add a new way of invoking completion events
callbacks. In the interrupt itself, we add the CQs which receive completion
event to a per-EQ list and schedule a tasklet. In the tasklet context
we loop over all the CQs in the list and invoke the user callback.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If mlx5_core_create_mkey fails, decrease the pending counter to undo the
previous increment.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Add required __acquire/__release statements to balance spinlock usage.
2. Change the index parameter of begin_wqe() to be unsigned to match supplied
argument type.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/scsi/scsi_debug.c
Agreed and tested resolution to a merge problem between a fix in scsi_debug
and a driver update
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For SPI drivers use the message definitions from scsi.h, and for target
drivers introduce a new TCM_*_TAG namespace.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com
Since we got rid of ordered tag support in 2010 the prime use case of
switching on and off ordered tags has been obsolete. The other function
of enabling/disabling tagging entirely has only been correctly implemented
by the 53c700 driver and isn't generally useful.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Drop the now unused reason argument from the ->change_queue_depth method.
Also add a return value to scsi_adjust_queue_depth, and rename it to
scsi_change_queue_depth now that it can be used as the default
->change_queue_depth implementation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
We won't ever queue more commands than the host allows. Instead of
letting drivers either reject or ignore this case handle it in
common code. Note that various driver use internal constant or
variables that are assigned to both shost->can_queue and checked
in ->change_queue_depth - I did remove those checks as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
All drivers use the implementation for ramping the queue up and down, so
instead of overloading the change_queue_depth method call the
implementation diretly if the driver opts into it by setting the
track_queue_depth flag in the host template.
Note that a few drivers validated the new queue depth in their
change_queue_depth method, but as we never go over the queue depth
set during slave_configure or the sysfs file this isn't nessecary
and can safely be removed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Venkatesh Srinivas <venkateshs@google.com>
This patch cleanups all PCIE, RSS & FW related macros/register defines that are
defined in t4fw_api.h and the affected files.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleanups PF/VF and LDST related macros/register defines that are
defined in t4fw_api.h and the affected files.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleanups all filter related macros/register defines that are defined
in t4fw_api.h and the affected files.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ieee802154/fakehard.c
A bug fix went into 'net' for ieee802154/fakehard.c, which is removed
in 'net-next'.
Add build fix into the merge from Stephen Rothwell in openvswitch, the
logging macros take a new initial 'log' argument, a new call was added
in 'net' so when we merge that in here we have to explicitly add the
new 'log' arg to it else the build fails.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull SCSI target fixes from Nicholas Bellinger:
"Here are the target-pending fixes queued for v3.18-rc6.
The highlights include:
- target-core OOPs fix with tcm_qla2xxx + vxworks FC initiators +
zero length SCSI commands having a transfer direction set. (Roland
+ Craig Watson)
- vhost-scsi OOPs fix to explicitly prevent WWPN endpoint configfs
group removal while qemu still has an active reference. (Paolo +
nab)
- ib_srpt fix for RDMA hardware with lower srp_sq_size limits.
(Bart)
- two ib_isert work-arounds for running on ocrdma hardware (Or + Sagi
+ Chris)
- iscsi-target discovery portal typo + SPC-3 PR Preempt SA key
matching fix (Steve)"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
IB/isert: Adjust CQ size to HW limits
target: return CONFLICT only when SA key unmatched
iser-target: Handle DEVICE_REMOVAL event on network portal listener correctly
ib_isert: Add max_send_sge=2 minimum for control PDU responses
srp-target: Retry when QP creation fails with ENOMEM
iscsi-target: return the correct port in SendTargets
vhost-scsi: Take configfs group dependency during VHOST_SCSI_SET_ENDPOINT
target: Don't call TFO->write_pending if data_length == 0
isert has an issue of trying to create a CQ with more CQEs than are
supported by the hardware, that currently results in failures during
isert_device creation during first session login.
This is the isert version of the patch that Minh Tran submitted for
iser, and is simple a workaround required to function with existing
ocrdma hardware.
Signed-off-by: Chris Moore <chris.moore@emulex.com>
Reviewied-by: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Previously, the driver queried the firmware in order to get the number
of supported EQs. Under SRIOV, since this was done before the driver
notified the firmware how many VFs it actually needs, the firmware had
to take into account a worst case scenario and always allocated four EQs
per VF, where one was used for events while the others were used for completions.
Now, when the firmware supports the asymmetric allocation scheme, denoted
by exposing num_sys_eqs > 0 (--> MLX4_DEV_CAP_FLAG2_SYS_EQS), we use the
QUERY_FUNC command to query the firmware before enabling SRIOV. Thus we
can get more EQs and MSI-X vectors per function.
Moreover, when running in the new firmware/driver mode, the limitation
that the number of EQs should be a power of two is lifted.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactored all macros used in cxgb4i as part of previously started cxgb4 macro
names cleanup. Makes them more uniform and avoids namespace collision.
Minor changes in other drivers where required as some of these macros are used
by multiple drivers, affected drivers are iw_cxgb4, cxgb4(vf) & csiostor
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least LID reassignment can trigger a race condition in the SRP
initiator driver, namely the receive completion handler trying to
post a request on a QP during or after QP destruction and before
the CQ's have been destroyed. Avoid this race by modifying a QP
into the error state and by waiting until all receive completions
have been processed before destroying a QP.
Reported-by: Max Gurtuvoy <maxg@mellanox.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Improve performance by using multiple RDMA/RC channels per SCSI
host for communication with an SRP target. About the
implementation:
- Introduce a loop over all channels in the code that uses
target->ch.
- Set the SRP_MULTICHAN_MULTI flag during login for the creation
of the second and subsequent channels.
- RDMA completion vectors are chosen such that RDMA completion
interrupts are handled by the CPU socket that submitted the I/O
request. As one can see in this patch it has been assumed if a
system contains n CPU sockets and m RDMA completion vectors
have been assigned to an RDMA HCA that IRQ affinity has been
configured such that completion vectors [i*m/n..(i+1)*m/n) are
bound to CPU socket i with 0 <= i < n.
- Modify srp_free_ch_ib() and srp_free_req_data() such that it
becomes safe to invoke these functions after the corresponding
allocation function failed.
- Add a ch_count sysfs attribute per target port.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Since the block layer already contains functionality to assign
a tag to each request, use that functionality instead of
reimplementing that functionality in the SRP initiator driver.
This change makes the free_reqs list superfluous. Hence remove
that list.
[hch: updated to use .use_blk_tags instead scsi_activate_tcq]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Changes in this patch:
- Move channel variables into a new structure (struct srp_rdma_ch).
- Add an srp_target_port pointer, 'lock' and 'comp_vector' members
in struct srp_rdma_ch.
- Add code to initialize these three new member variables.
- Many boring "target->" into "ch->" changes.
- The cm_id and completion handler context pointers are now of type
srp_rdma_ch * instead of srp_target_port *.
- Three kzalloc(a * b, f) calls have been changed into kcalloc(a, b, f)
to avoid that this patch would trigger a checkpatch warning.
- Two casts from u64 into unsigned long long have been left out
because these are superfluous. Since considerable time u64 is
defined as unsigned long long for all architectures supported by
the Linux kernel.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Introduce the srp_target_port member variables 'sgid' and 'pkey'.
Change the type of 'orig_dgid' from __be16[8] into union ib_gid.
This patch does not change any functionality but makes the
"Separate target and channel variables" patch easier to verify.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
If a cable is pulled during LUN scanning it can happen that the
SRP rport and the SCSI host have been created but no LUNs have been
added to the SCSI host. Since multipathd only sends SCSI commands
to a SCSI target if one or more SCSI devices are present and since
there is no keepalive mechanism for IB queue pairs this means that
after a LUN scan failed and after a reconnect has succeeded no
data will be sent over the QP and hence that a subsequent cable
pull will not be detected. Avoid this by not creating an rport or
SCSI host if a cable is pulled during a SCSI LUN scan.
Note: so far the above behavior has only been observed with the
kernel module parameter ch_count set to a value >= 2.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Attempting to connect three times may be insufficient after an
initiator system tries to relogin, especially if the relogin
attempt occurs before the SRP target service ID has been
registered. Since the srp_daemon retries a failed login attempt
anyway, remove the stale connection retry mechanism.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The patch that adds multichannel support into the SRP initiator
driver introduces an additional call to srp_free_ch_ib(). This
patch helps to keep that later patch simple.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Remove the tagged argument from scsi_adjust_queue_depth, and just let it
handle the queue depth. For most drivers those two are fairly separate,
given that most modern drivers don't care about the SCSI "tagged" status
of a command at all, and many old drivers allow queuing of multiple
untagged commands in the driver.
Instead we start out with the ->simple_tags flag set before calling
->slave_configure, which is how all drivers actually looking at
->simple_tags except for one worke anyway. The one other case looks
broken, but I've kept the behavior as-is for now.
Except for that we only change ->simple_tags from the ->change_queue_type,
and when rejecting a tag message in a single driver, so keeping this
churn out of scsi_adjust_queue_depth is a clear win.
Now that the usage of scsi_adjust_queue_depth is more obvious we can
also remove all the trivial instances in ->slave_alloc or ->slave_configure
that just set it to the cmd_per_lun default.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Most drivers use exactly the same implementation, so provide it as a
library function.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Various patches have ended up changing the style of the symbolic macros/register
defines to different style.
As a result, the current kernel.org files are a mix of different macro styles.
Since this macro/register defines is used by different drivers a
few patch series have ended up adding duplicate macro/register define entries
with different styles. This makes these register define/macro files a complete
mess and we want to make them clean and consistent. This patch cleans up a part
of it.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this case the cm_id->context is the isert_np, and the cm_id->qp
is NULL, so use that to distinct the cases.
Since we don't expect any other events on this cm_id we can
just return -1 for explicit termination of the cm_id by the
cma layer.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Doug Ledford