Commit 1d4639567d ("mdio_bus: Fix PTR_ERR applied after initialization
to constant") accidentally changed a check from -ENOTSUPP to -ENOSYS,
causing failures if reset controller support is not enabled. E.g. on
r7s72100/rskrza1:
sh-eth e8203000.ethernet: MDIO init failed: -524
sh-eth: probe of e8203000.ethernet failed with error -524
Seen on r8a7740/armadillo, r7s72100/rskrza1, and r7s9210/rza2mevb.
Fixes: 1d4639567d ("mdio_bus: Fix PTR_ERR applied after initialization to constant")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: YueHaibing <yuehaibing@huawei.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 075e238d12.
Going to go with Geert's fix instead, which also has a
correct Fixes tag.
Signed-off-by: David S. Miller <davem@davemloft.net>
According to hardware user manual, bits5~7 in register
HCLGE_MISC_VECTOR_INT_STS means reset interrupts status,
but HCLGE_RESET_INT_M is defined as bits0~2 now. So it
will make hclge_reset_err_handle() read the wrong reset
interrupt status.
This patch fixes this wrong bit mask.
Fixes: 2336f19d78 ("net: hns3: check reset interrupt status when reset fails")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pm_runtime_put_autosuspend in probe will call runtime suspend to
disable clks automatically if CONFIG_PM is defined. (If CONFIG_PM
is not defined, its implementation will be empty, then runtime
suspend will not be called.)
Therefore, we can call pm_runtime_get_sync to runtime resume it
first to enable clks, which matches the runtime suspend. (Only when
CONFIG_PM is defined, otherwise pm_runtime_get_sync will also be
empty, then runtime resume will not be called.)
Then it is fine to disable clks without causing clock count mis-match.
Fixes: c43eab3edd ("net: fec: add missed clk_disable_unprepare in remove")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modifying the link settings via phylink_ethtool_ksettings_set() and
phylink_ethtool_set_pauseparam() didn't always work as intended for
PHY based setups, as calling phylink_mac_config() would result in the
unresolved configuration being committed to the MAC, rather than the
configuration with the speed and duplex setting.
This would work fine if the update caused the link to renegotiate,
but if no settings have changed, phylib won't trigger a renegotiation
cycle, and the MAC will be left incorrectly configured.
Avoid calling phylink_mac_config() unless we are using an inband mode
in phylink_ethtool_ksettings_set(), and use phy_set_asym_pause() as
introduced in 4.20 to set the PHY settings in
phylink_ethtool_set_pauseparam().
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the documentation on phylink's create and destroy functions to
explicitly state that the rtnl lock must not be held while calling
these.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
During performance testing, I found that one of my r8169 NICs suffered
a major performance loss, a 8168c model.
Running netperf's TCP_STREAM test didn't return the expected
throughput of > 900 Mb/s, but rather only about 22 Mb/s. Strange
enough, running the TCP_MAERTS and UDP_STREAM tests all returned with
throughput > 900 Mb/s, as did TCP_STREAM with the other r8169 NICs I can
test (either one of 8169s, 8168e, 8168f).
Bisecting turned up commit 93681cd7d9,
"r8169: enable HW csum and TSO" as the culprit.
I added my 8168c version, RTL_GIGA_MAC_VER_22, to the code
special-casing the 8168evl as per the patch below. This fixed the
performance problem for me.
Fixes: 93681cd7d9 ("r8169: enable HW csum and TSO")
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I prefer to use my personal email address for kernel related work.
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Acked-by: Rain River <rain.1986.08.12@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The taprio qdisc allows to set mqprio setting but only once. In case
if mqprio settings are provided next time the error is returned as
it's not allowed to change traffic class mapping in-flignt and that
is normal. But if configuration is absolutely the same - no need to
return error. It allows to provide same command couple times,
changing only base time for instance, or changing only scheds maps,
but leaving mqprio setting w/o modification. It more corresponds the
message: "Changing the traffic mapping of a running schedule is not
supported", so reject mqprio if it's really changed.
Also corrected TC_BITMASK + 1 for consistency, as proposed.
Fixes: a3d43c0d56 ("taprio: Add support adding an admin schedule")
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bring back tls_sw_sendpage_locked. sk_msg redirection into a socket
with TLS_TX takes the following path:
tcp_bpf_sendmsg_redir
tcp_bpf_push_locked
tcp_bpf_push
kernel_sendpage_locked
sock->ops->sendpage_locked
Also update the flags test in tls_sw_sendpage_locked to allow flag
MSG_NO_SHARED_FRAGS. bpf_tcp_sendmsg sets this.
Link: https://lore.kernel.org/netdev/CA+FuTSdaAawmZ2N8nfDDKu3XLpXBbMtcCT0q4FntDD2gn8ASUw@mail.gmail.com/T/#t
Link: https://github.com/wdebruij/kerneltools/commits/icept.2
Fixes: 0608c69c9a ("bpf: sk_msg, sock{map|hash} redirect through ULP")
Fixes: f3de19af0f ("Revert \"net/tls: remove unused function tls_sw_sendpage_locked\"")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In afs_wait_for_call_to_complete(), rather than immediately aborting an
operation if a signal occurs, the code attempts to wait for it to
complete, using a schedule timeout of 2*RTT (or min 2 jiffies) and a
check that we're still receiving relevant packets from the server before
we consider aborting the call. We may even ping the server to check on
the status of the call.
However, there's a missing timeout reset in the event that we do
actually get a packet to process, such that if we then get a couple of
short stalls, we then time out when progress is actually being made.
Fix this by resetting the timeout any time we get something to process.
If it's the failure of the call then the call state will get changed and
we'll exit the loop shortly thereafter.
A symptom of this is data fetches and stores failing with EINTR when
they really shouldn't.
Fixes: bc5e3a546d ("rxrpc: Use MSG_WAITALL to tell sendmsg() to temporarily ignore signals")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The previous commit had a bug where the last page in the memory range
could not be synced. This change fixes the behavior so that all the
required pages are synced.
Fixes: 9cfeeb576d ("gve: Fixes DMA synchronization")
Signed-off-by: Adi Suresh <adisuresh@google.com>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For our current users we don't expect pool objects to be writable from
the gpu.
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Fixes: 4f7af1948a ("drm/i915: Support ro ppgtt mapped cmdparser shadow buffers")
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191119150154.18249-1-matthew.auld@intel.com
(cherry picked from commit d18580b08b)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Commit 1d4639567d ("mdio_bus: Fix PTR_ERR applied after initialization
to constant") accidentally changed a check from -ENOTSUPP to -ENOSYS,
causing failures if reset controller support is not enabled. E.g. on
r7s72100/rskrza1:
sh-eth e8203000.ethernet: MDIO init failed: -524
sh-eth: probe of e8203000.ethernet failed with error -524
Seen on r8a7740/armadillo, r7s72100/rskrza1, and r7s9210/rza2mevb.
Fixes: 1d4639567d ("mdio_bus: Fix PTR_ERR applied after initialization to constant")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: YueHaibing <yuehaibing@huawei.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Before returning NULL, put the sock first.
Cc: stable@vger.kernel.org
Fixes: cf1b2326b7 ("nbd: verify socket is supported during setup")
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Sun Ke <sunke32@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When we hot unplug a virtserialport and then try to hot plug again,
it fails:
(qemu) chardev-add socket,id=serial0,path=/tmp/serial0,server,nowait
(qemu) device_add virtserialport,bus=virtio-serial0.0,nr=2,\
chardev=serial0,id=serial0,name=serial0
(qemu) device_del serial0
(qemu) device_add virtserialport,bus=virtio-serial0.0,nr=2,\
chardev=serial0,id=serial0,name=serial0
kernel error:
virtio-ports vport2p2: Error allocating inbufs
qemu error:
virtio-serial-bus: Guest failure in adding port 2 for device \
virtio-serial0.0
This happens because buffers for the in_vq are allocated when the port is
added but are not released when the port is unplugged.
They are only released when virtconsole is removed (see a7a69ec0d8)
To avoid the problem and to be symmetric, we could allocate all the buffers
in init_vqs() as they are released in remove_vqs(), but it sounds like
a waste of memory.
Rather than that, this patch changes add_port() logic to ignore ENOSPC
error in fill_queue(), which means queue has already been filled.
Fixes: a7a69ec0d8 ("virtio_console: free buffers after reset")
Cc: mst@redhat.com
Cc: stable@vger.kernel.org
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Commit 780bc7903a ("virtio_ring: Support DMA APIs") makes
virtqueue_add() return -EIO when we fail to map our I/O buffers. This is
a very realistic scenario for guests with encrypted memory, as swiotlb
may run out of space, depending on it's size and the I/O load.
The virtio-blk driver interprets -EIO form virtqueue_add() as an IO
error, despite the fact that swiotlb full is in absence of bugs a
recoverable condition.
Let us change the return code to -ENOMEM, and make the block layer
recover form these failures when virtio-blk encounters the condition
described above.
Cc: stable@vger.kernel.org
Fixes: 780bc7903a ("virtio_ring: Support DMA APIs")
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Tested-by: Michael Mueller <mimu@linux.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When CONFIG_RESET_CONTROLLER is disabled, the
devm_reset_control_get_exclusive function returns -ENOTSUPP. This is not
handled in subsequent check and then the mdio device fails to probe.
When CONFIG_RESET_CONTROLLER is enabled, its code checks in OF for reset
device, and since it is not present, returns -ENOENT. -ENOENT is handled.
Add -ENOTSUPP also.
This happened to me when upgrading kernel on Turris Omnia. You either
have to enable CONFIG_RESET_CONTROLLER or use this patch.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Fixes: 71dd6c0dff ("net: phy: add support for reset-controller")
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit eec4844fae ("proc/sysctl: add shared variables for range
check") did:
- .extra2 = &two,
+ .extra2 = SYSCTL_ONE,
here, which doesn't seem to be intentional, given the changelog.
This patch restores it to the previous, as the value of 2 still makes
sense (used in fib_multipath_hash()).
Fixes: eec4844fae ("proc/sysctl: add shared variables for range check")
Cc: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver forgets to disable the regulator in remove like what is done
in probe failure.
Add the missed call to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XDP_TX rings should not be limited by max_num_tx_rings_p_up.
To make sure total number of TX rings never exceed MAX_TX_RINGS,
add similar check in mlx4_en_alloc_tx_queue_per_tc(), where
a new value is assigned for num_up.
Fixes: 7e1dc5e926 ("net/mlx4_en: Limit the number of TX rings")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
info->options_len is 'u8' type, and when opts_len with a value >
IP_TUNNEL_OPTS_MAX, 'info->options_len = opts_len' will cast int
to u8 and set a wrong value to info->options_len.
Kernel crashed in my test when doing:
# opts="0102:80:00800022"
# for i in {1..99}; do opts="$opts,0102:80:00800022"; done
# ip link add name geneve0 type geneve dstport 0 external
# tc qdisc add dev eth0 ingress
# tc filter add dev eth0 protocol ip parent ffff: \
flower indev eth0 ip_proto udp action tunnel_key \
set src_ip 10.0.99.192 dst_ip 10.0.99.193 \
dst_port 6081 id 11 geneve_opts $opts \
action mirred egress redirect dev geneve0
So we should do the similar check as cls_flower does, return error
when opts_len > IP_TUNNEL_OPTS_MAX in tunnel_key_copy_opts().
Fixes: 0ed5269f9e ("net/sched: add tunnel option support to act_tunnel_key")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The helper mlxsw_sp_ipip_dev_ul_tb_id() determines the underlay VRF of a
GRE tunnel. For a tunnel without a bound device, it uses the same VRF that
the tunnel is in. However in Linux, a GRE tunnel without a bound device
uses the main VRF as the underlay. Fix the function accordingly.
mlxsw further assumed that moving a tunnel to a different VRF could cause
conflict in local tunnel endpoint address, which cannot be offloaded.
However, the only way that an underlay could be changed by moving the
tunnel device itself is if the tunnel device does not have a bound device.
But in that case the underlay is always the main VRF, so there is no
opportunity to introduce a conflict by moving such device. Thus this check
constitutes a dead code, and can be removed, which do.
Fixes: 6ddb7426a7 ("mlxsw: spectrum_router: Introduce loopback RIFs")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of errors in unlink_clip_vcc, the logging level is set to
pr_crit but failures in clip_setentry are handled by pr_err().
The patch changes the severity consistent across invocations.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the execlists_active() is no longer protected by the
engine->active.lock, we need to protect the request pointer with RCU to
prevent it being freed as we evaluate whether or not we need to preempt.
Fixes: df40306902 ("drm/i915/execlists: Lift process_csb() out of the irq-off spinlock")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191104090158.2959-2-chris@chris-wilson.co.uk
(cherry picked from commit 7d14863525)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
(cherry picked from commit 8eb4704b12)
(cherry picked from commit 7e27238e149ce4f00d9cd801fe3aa0ea55e986a2)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
set_page_dirty says:
For pages with a mapping this should be done under the page lock
for the benefit of asynchronous memory errors who prefer a
consistent dirty state. This rule can be broken in some special
cases, but should be better not to.
Under those rules, it is only safe for us to use the plain set_page_dirty
calls for shmemfs/anonymous memory. Userptr may be used with real
mappings and so needs to use the locked version (set_page_dirty_lock).
However, following a try_to_unmap() we may want to remove the userptr and
so call put_pages(). However, try_to_unmap() acquires the page lock and
so we must avoid recursively locking the pages ourselves -- which means
that we cannot safely acquire the lock around set_page_dirty(). Since we
can't be sure of the lock, we have to risk skip dirtying the page, or
else risk calling set_page_dirty() without a lock and so risk fs
corruption.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203317
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=112012
Fixes: 5cc9ed4b9a ("drm/i915: Introduce mapping of user pages into video memory (userptr) ioctl")
References: cb6d7c7dc7 ("drm/i915/userptr: Acquire the page lock around set_page_dirty()")
References: 505a8ec7e1 ("Revert "drm/i915/userptr: Acquire the page lock around set_page_dirty()"")
References: 6dcc693bc5 ("ext4: warn when page is dirtied without buffers")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191111133205.11590-1-chris@chris-wilson.co.uk
(cherry picked from commit 0d4bbe3d40)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
(cherry picked from commit cee7fb437e)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
We report "frequencies" (actual-frequency, requested-frequency) as the
number of accumulated cycles so that the average frequency over that
period may be determined by the user. This means the units we report to
the user are Mcycles (or just M), not MHz.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191109105356.5273-1-chris@chris-wilson.co.uk
(cherry picked from commit e88866ef02)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
(cherry picked from commit a7d87b70d6)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The LUTs are single buffered so in order to program them without
tearing we'd have to do it during vblank (actually to be 100%
effective it has to happen between start of vblank and frame start).
We have no proper mechanism for that at the moment so we just
defer loading them after the vblank waits have happened. That
is not quite sufficient (especially when committing multiple pipes
whose vblanks don't line up) so the LUT load will often leak into
the following frame causing tearing.
However in case the hardware wasn't previously using the LUT we
can preload it before setting the enable bit (which is double
buffered so won't tear). Let's determine if we can do such
preloading and make it happen. Slight variation between the
hardware requires some platforms specifics in the checks.
Hans is seeing ugly colored flash on VLV/CHV macchines (GPD win
and Asus T100HA) when the gamma LUT gets loaded for the first
time as the BIOS has left some junk in the LUT memory.
v2: Deal with uapi vs. hw crtc state split
s/GCM/CGM/ typo fix
Cc: Hans de Goede <hdegoede@redhat.com>
Fixes: 051a6d8d3c ("drm/i915: Move LUT programming to happen after vblank waits")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191030190815.7359-1-ville.syrjala@linux.intel.com
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
(cherry picked from commit 0ccc42a2fd)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
(cherry picked from commit f77021372e)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Make sure we have a crtc before probing its primary plane's
max stride. Initially I thought we can't get this far without
crtcs, but looks like we can via the dumb_create ioctl.
Not sure if we shouldn't disable dumb buffer support entirely
when we have no crtcs, but that would require some amount of work
as the only thing currently being checked is dev->driver->dumb_create
which we'd have to convert to some device specific dynamic thing.
Cc: stable@vger.kernel.org
Reported-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Fixes: aa5ca8b742 ("drm/i915: Align dumb buffer stride to 4k to allow for gtt remapping")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191106172349.11987-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit baea9ffe64)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
(cherry picked from commit aeec766133)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Including:
- Fix for Intel IOMMU to correct invalidation commands
when in SVA mode.
- Update MAINTAINERS entry for Intel IOMMU
-----BEGIN PGP SIGNATURE-----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=5/bw
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu fixes from Joerg Roedel:
- Fix for Intel IOMMU to correct invalidation commands when in SVA
mode.
- Update MAINTAINERS entry for Intel IOMMU
* tag 'iommu-fixes-v5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Fix QI_DEV_IOTLB_PFSID and QI_DEV_EIOTLB_PFSID macros
MAINTAINERS: Update for INTEL IOMMU (VT-d) entry
ethtool expects ETHTOOL_GRXCLSRLALL to set ethtool_rxnfc->data with the
total number of entries in the rx classifier table. Surprisingly, mlx4
is missing this part (in principle ethtool could still move forward and
try the insert).
Tested: compiled and run command:
phh13:~# ethtool -N eth1 flow-type udp4 queue 4
Added rule with ID 255
Signed-off-by: Luigi Rizzo <lrizzo@google.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Daniel Borkmann says:
====================
pull-request: bpf 2019-11-15
The following pull-request contains BPF updates for your *net* tree.
We've added 1 non-merge commits during the last 9 day(s) which contain
a total of 1 file changed, 3 insertions(+), 1 deletion(-).
The main changes are:
1) Fix a missing unlock of bpf_devs_lock in bpf_offload_dev_create()'s
error path, from Dan.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull i2c fixes from Wolfram Sang:
"An I2C core fix to prevent a use-after-free in a rare error path,
and an I2C ACPI addition to work around broken HW/firmware related
to touchscreens"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: core: fix use after free in of_i2c_notify
i2c: acpi: Force bus speed to 400KHz if a Silead touchscreen is present
Pull crypto fix from Herbert Xu:
"This reverts a number of changes to the khwrng thread which feeds the
kernel random number pool from hwrng drivers. They were trying to fix
issues with suspend-and-resume but ended up causing regressions"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
Revert "hwrng: core - Freeze khwrng thread during suspend"
This reverts commit 03a3bb7ae6 ("hwrng: core - Freeze khwrng
thread during suspend"), ff296293b3 ("random: Support freezable
kthreads in add_hwgenerator_randomness()") and 59b569480d ("random:
Use wait_event_freezable() in add_hwgenerator_randomness()").
These patches introduced regressions and we need more time to
get them ready for mainline.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull x86 fixes from Ingo Molnar:
"Two fixes: disable unreliable HPET on Intel Coffe Lake platforms, and
fix a lockdep splat in the resctrl code"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/resctrl: Fix potential lockdep warning
x86/quirks: Disable HPET on Intel Coffe Lake platforms
Pull perf fixes from Ingo Molnar:
"Misc fixes: a handful of AUX event handling related fixes, a Sparse
fix and two ABI fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Fix missing static inline on perf_cgroup_switch()
perf/core: Consistently fail fork on allocation failures
perf/aux: Disallow aux_output for kernel events
perf/core: Reattach a misplaced comment
perf/aux: Fix the aux_output group inheritance fix
perf/core: Disallow uncore-cgroup events
Pull networking fixes from David Miller:
1) Fix memory leak in xfrm_state code, from Steffen Klassert.
2) Fix races between devlink reload operations and device
setup/cleanup, from Jiri Pirko.
3) Null deref in NFC code, from Stephan Gerhold.
4) Refcount fixes in SMC, from Ursula Braun.
5) Memory leak in slcan open error paths, from Jouni Hogander.
6) Fix ETS bandwidth validation in hns3, from Yonglong Liu.
7) Info leak on short USB request answers in ax88172a driver, from
Oliver Neukum.
8) Release mem region properly in ep93xx_eth, from Chuhong Yuan.
9) PTP config timestamp flags validation, from Richard Cochran.
10) Dangling pointers after SKB data realloc in seg6, from Andrea Mayer.
11) Missing free_netdev() in gemini driver, from Chuhong Yuan.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (56 commits)
ipmr: Fix skb headroom in ipmr_get_route().
net: hns3: cleanup of stray struct hns3_link_mode_mapping
net/smc: fix fastopen for non-blocking connect()
rds: ib: update WR sizes when bringing up connection
net: gemini: add missed free_netdev
net: dsa: tag_8021q: Fix dsa_8021q_restore_pvid for an absent pvid
seg6: fix skb transport_header after decap_and_validate()
seg6: fix srh pointer in get_srh()
net: stmmac: Use the correct style for SPDX License Identifier
octeontx2-af: Use the correct style for SPDX License Identifier
ptp: Extend the test program to check the external time stamp flags.
mlx5: Reject requests to enable time stamping on both edges.
igb: Reject requests that fail to enable time stamping on both edges.
dp83640: Reject requests to enable time stamping on both edges.
mv88e6xxx: Reject requests to enable time stamping on both edges.
ptp: Introduce strict checking of external time stamp options.
renesas: reject unsupported external timestamp flags
mlx5: reject unsupported external timestamp flags
igb: reject unsupported external timestamp flags
dp83640: reject unsupported external timestamp flags
...
In route.c, inet_rtm_getroute_build_skb() creates an skb with no
headroom. This skb is then used by inet_rtm_getroute() which may pass
it to rt_fill_info() and, from there, to ipmr_get_route(). The later
might try to reuse this skb by cloning it and prepending an IPv4
header. But since the original skb has no headroom, skb_push() triggers
skb_under_panic():
skbuff: skb_under_panic: text:00000000ca46ad8a len:80 put:20 head:00000000cd28494e data:000000009366fd6b tail:0x3c end:0xec0 dev:veth0
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:108!
invalid opcode: 0000 [#1] SMP KASAN PTI
CPU: 6 PID: 587 Comm: ip Not tainted 5.4.0-rc6+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-2.fc30 04/01/2014
RIP: 0010:skb_panic+0xbf/0xd0
Code: 41 a2 ff 8b 4b 70 4c 8b 4d d0 48 c7 c7 20 76 f5 8b 44 8b 45 bc 48 8b 55 c0 48 8b 75 c8 41 54 41 57 41 56 41 55 e8 75 dc 7a ff <0f> 0b 0f 1f 44 00 00 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00
RSP: 0018:ffff888059ddf0b0 EFLAGS: 00010286
RAX: 0000000000000086 RBX: ffff888060a315c0 RCX: ffffffff8abe4822
RDX: 0000000000000000 RSI: 0000000000000008 RDI: ffff88806c9a79cc
RBP: ffff888059ddf118 R08: ffffed100d9361b1 R09: ffffed100d9361b0
R10: ffff88805c68aee3 R11: ffffed100d9361b1 R12: ffff88805d218000
R13: ffff88805c689fec R14: 000000000000003c R15: 0000000000000ec0
FS: 00007f6af184b700(0000) GS:ffff88806c980000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007ffc8204a000 CR3: 0000000057b40006 CR4: 0000000000360ee0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
skb_push+0x7e/0x80
ipmr_get_route+0x459/0x6fa
rt_fill_info+0x692/0x9f0
inet_rtm_getroute+0xd26/0xf20
rtnetlink_rcv_msg+0x45d/0x630
netlink_rcv_skb+0x1a5/0x220
rtnetlink_rcv+0x15/0x20
netlink_unicast+0x305/0x3a0
netlink_sendmsg+0x575/0x730
sock_sendmsg+0xb5/0xc0
___sys_sendmsg+0x497/0x4f0
__sys_sendmsg+0xcb/0x150
__x64_sys_sendmsg+0x48/0x50
do_syscall_64+0xd2/0xac0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Actually the original skb used to have enough headroom, but the
reserve_skb() call was lost with the introduction of
inet_rtm_getroute_build_skb() by commit 404eb77ea7 ("ipv4: support
sport, dport and ip_proto in RTM_GETROUTE").
We could reserve some headroom again in inet_rtm_getroute_build_skb(),
but this function shouldn't be responsible for handling the special
case of ipmr_get_route(). Let's handle that directly in
ipmr_get_route() by calling skb_realloc_headroom() instead of
skb_clone().
Fixes: 404eb77ea7 ("ipv4: support sport, dport and ip_proto in RTM_GETROUTE")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans-up the stray left over code. It has no
functionality impact.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FASTOPEN does not work with SMC-sockets. Since SMC allows fallback to
TCP native during connection start, the FASTOPEN setsockopts trigger
this fallback, if the SMC-socket is still in state SMC_INIT.
But if a FASTOPEN setsockopt is called after a non-blocking connect(),
this is broken, and fallback does not make sense.
This change complements
commit cd2063604e ("net/smc: avoid fallback in case of non-blocking connect")
and fixes the syzbot reported problem "WARNING in smc_unhash_sk".
Reported-by: syzbot+8488cc4cf1c9e09b8b86@syzkaller.appspotmail.com
Fixes: e1bbdd5704 ("net/smc: reduce sock_put() for fallback sockets")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently WR sizes are updated from rds_ib_sysctl_max_send_wr and
rds_ib_sysctl_max_recv_wr when a connection is shut down. As a result,
a connection being down while rds_ib_sysctl_max_send_wr or
rds_ib_sysctl_max_recv_wr are updated, will not update the sizes when
it comes back up.
Move resizing of WRs to rds_ib_setup_qp so that connections will be setup
with the most current WR sizes.
Signed-off-by: Dag Moxnes <dag.moxnes@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver forgets to free allocated netdev in remove like
what is done in probe failure.
Add the free to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This sequence of operations:
ip link set dev br0 type bridge vlan_filtering 1
bridge vlan del dev swp2 vid 1
ip link set dev br0 type bridge vlan_filtering 1
ip link set dev br0 type bridge vlan_filtering 0
apparently fails with the message:
[ 31.305716] sja1105 spi0.1: Reset switch and programmed static config. Reason: VLAN filtering
[ 31.322161] sja1105 spi0.1: Couldn't determine PVID attributes (pvid 0)
[ 31.328939] sja1105 spi0.1: Failed to setup VLAN tagging for port 1: -2
[ 31.335599] ------------[ cut here ]------------
[ 31.340215] WARNING: CPU: 1 PID: 194 at net/switchdev/switchdev.c:157 switchdev_port_attr_set_now+0x9c/0xa4
[ 31.349981] br0: Commit of attribute (id=6) failed.
[ 31.354890] Modules linked in:
[ 31.357942] CPU: 1 PID: 194 Comm: ip Not tainted 5.4.0-rc6-01792-gf4f632e07665-dirty #2062
[ 31.366167] Hardware name: Freescale LS1021A
[ 31.370437] [<c03144dc>] (unwind_backtrace) from [<c030e184>] (show_stack+0x10/0x14)
[ 31.378153] [<c030e184>] (show_stack) from [<c11d1c1c>] (dump_stack+0xe0/0x10c)
[ 31.385437] [<c11d1c1c>] (dump_stack) from [<c034c730>] (__warn+0xf4/0x10c)
[ 31.392373] [<c034c730>] (__warn) from [<c034c7bc>] (warn_slowpath_fmt+0x74/0xb8)
[ 31.399827] [<c034c7bc>] (warn_slowpath_fmt) from [<c11ca204>] (switchdev_port_attr_set_now+0x9c/0xa4)
[ 31.409097] [<c11ca204>] (switchdev_port_attr_set_now) from [<c117036c>] (__br_vlan_filter_toggle+0x6c/0x118)
[ 31.418971] [<c117036c>] (__br_vlan_filter_toggle) from [<c115d010>] (br_changelink+0xf8/0x518)
[ 31.427637] [<c115d010>] (br_changelink) from [<c0f8e9ec>] (__rtnl_newlink+0x3f4/0x76c)
[ 31.435613] [<c0f8e9ec>] (__rtnl_newlink) from [<c0f8eda8>] (rtnl_newlink+0x44/0x60)
[ 31.443329] [<c0f8eda8>] (rtnl_newlink) from [<c0f89f20>] (rtnetlink_rcv_msg+0x2cc/0x51c)
[ 31.451477] [<c0f89f20>] (rtnetlink_rcv_msg) from [<c1008df8>] (netlink_rcv_skb+0xb8/0x110)
[ 31.459796] [<c1008df8>] (netlink_rcv_skb) from [<c1008648>] (netlink_unicast+0x17c/0x1f8)
[ 31.468026] [<c1008648>] (netlink_unicast) from [<c1008980>] (netlink_sendmsg+0x2bc/0x3b4)
[ 31.476261] [<c1008980>] (netlink_sendmsg) from [<c0f43858>] (___sys_sendmsg+0x230/0x250)
[ 31.484408] [<c0f43858>] (___sys_sendmsg) from [<c0f44c84>] (__sys_sendmsg+0x50/0x8c)
[ 31.492209] [<c0f44c84>] (__sys_sendmsg) from [<c0301000>] (ret_fast_syscall+0x0/0x28)
[ 31.500090] Exception stack(0xedf47fa8 to 0xedf47ff0)
[ 31.505122] 7fa0: 00000002 b6f2e060 00000003 beabd6a4 00000000 00000000
[ 31.513265] 7fc0: 00000002 b6f2e060 5d6e3213 00000128 00000000 00000001 00000006 000619c4
[ 31.521405] 7fe0: 00086078 beabd658 0005edbc b6e7ce68
The reason is the implementation of br_get_pvid:
static inline u16 br_get_pvid(const struct net_bridge_vlan_group *vg)
{
if (!vg)
return 0;
smp_rmb();
return vg->pvid;
}
Since VID 0 is an invalid pvid from the bridge's point of view, let's
add this check in dsa_8021q_restore_pvid to avoid restoring a pvid that
doesn't really exist.
Fixes: 5f33183b7f ("net: dsa: tag_8021q: Restore bridge VLANs when enabling vlan_filtering")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrea Mayer says:
====================
seg6: fixes to Segment Routing in IPv6
This patchset is divided in 2 patches and it introduces some fixes
to Segment Routing in IPv6, which are:
- in function get_srh() fix the srh pointer after calling
pskb_may_pull();
- fix the skb->transport_header after calling decap_and_validate()
function;
Any comments on the patchset are welcome.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
in the receive path (more precisely in ip6_rcv_core()) the
skb->transport_header is set to skb->network_header + sizeof(*hdr). As a
consequence, after routing operations, destination input expects to find
skb->transport_header correctly set to the next protocol (or extension
header) that follows the network protocol. However, decap behaviors (DX*,
DT*) remove the outer IPv6 and SRH extension and do not set again the
skb->transport_header pointer correctly. For this reason, the patch sets
the skb->transport_header to the skb->network_header + sizeof(hdr) in each
DX* and DT* behavior.
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geert Uytterhoeven