On some buggy chips, "vlan tag present" flag is set which causes packet
loss. Fix this by checking if rx vlan accel is enabled in features.
Reported-by: Michael Guntsche <mguntsche@gmail.com>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By a6b7a40786, remove interrupt.h
from netdevice.h. But this forget to revise sh_eth.
This fix the build failure.
error: expected '=', ',', ';', 'asm' or '__attribute__' before 'sh_eth_interrupt'
error: implicit declaration of function 'request_irq'
error: 'sh_eth_interrupt' undeclared (first use in this function)
error: (Each undeclared identifier is reported only once
drivers/net/sh_eth.c:1386: error: for each function it appears in.)
error: 'IRQF_SHARED' undeclared (first use in this function)
error: implicit declaration of function 'free_irq'
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In this code, the failure_cleanup label calls the function
plx_pci_del_card, which frees everything in the card->net_dev array. dev
is placed in this array immediately after allocation, so the two subsequent
jumps to failure_cleanup should not also call free_sja1000dev, but the
second one does.
If plx_pci_check_sja1000 fails, then free_sja1000dev is also called on
dev. Because dev is already in the card->net_dev array, this implies that
when plx_pci_del_card is later called, it may get freed again. So that
entry is reset to NULL after the free.
Finally, if there is a problem with one channel, there will be a hole in the
array. card->channels counts the number of channels that have succeeded,
and does not keep track of the index of the largest element in the array
that is valid. So the loop in plx_pci_del_card is changed to go up to
PLX_PCI_MAX_CHAN, which is only 2.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cdc_ncm driver still has a few places where stack variables are
passed to the cdc_ncm_do_request function. This triggers a stack trace in
lib/dma-debug.c if the CONFIG_DEBUG_DMA_API option is set.
Adjust these calls to pass parameters that have been allocated with
kzalloc.
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vmxnet3 driver enables vlan filters if filtering is enabled for
any vlan. In promiscuous mode the filter table is cleared to in
order to disable filtering. However, if a vlan device is subsequently
created that vlan will be added to the filter, re-engaging it. As a
result, not only do we not see all the vlans in promiscuous mode, we
don't even see vlans for which a filter was previously created.
CC: Scott J. Goldman <scottjg@vmware.com>
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: VMware PV-Drivers <pv-drivers@vmware.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Host driver can't get a hint of DDR mode through ios->ddr flag anymore.
ios->timing is currently used to inform DDR mode as a substitute.
And capability of MMC_CAP_MMC_HIGHSPEED is added for DDR support.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When timeout_clk is calculated the host->clock could be zero.
So, instead of host->clock the calculation now uses mmc->f_max.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This moves the calculation below the assignment of mmc->f_max, which
we need for calculating timeout_clk in the next patch in this series.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This reverts commit 4b01681c77, which introduced a new potential
divide by zero in the process of fixing one. The subsequent commits
attempt to fix the issue properly.
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix below compile warning:
CC drivers/mmc/host/tmio_mmc.o
drivers/mmc/host/tmio_mmc.c: In function 'tmio_mmc_suspend':
drivers/mmc/host/tmio_mmc.c:30: warning: unused variable 'mmc'
drivers/mmc/host/tmio_mmc.c: In function 'tmio_mmc_resume':
drivers/mmc/host/tmio_mmc.c:45: warning: unused variable 'mmc'
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Apply a workaround for the imx eSDHC controller to avoid missing
card interrupts. This makes SDIO work.
Signed-off-by: Tony Lin <tony.lin@freescale.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
A header change has removed an implicit inclusion of module.h, breaking
the build due to the use of THIS_MODULE. Fix that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The mask used inside this macro was assuming Buffer_Size1's [BS1's]
width to be 14 bits, it is actually 13 bits. Modify masks used in
IDMAC_SET_BUFFER1_SIZE such that they use only 13 bits instead of
current 14.
Signed-off-by: Shashidhar Hiremath <shashidharh@vayavyalabs.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
During card removal and inserting cycle the test file in the debugfs could be
stalled until the host driver removes it. Let's keep the file in the linked
list and destroy it when card is removed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Samsung SoCs need to set BROKEN_ADMA_ZEROLEN_DESC.
(If ADMA operation is more than 65535, maybe set by zero.)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Enable the quirk.
(Best used in conjunction with patch downgrading ADMA to SDMA when
transfer is not aligned.)
Signed-off-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently, the retuning timer for retuning mode 1 will be deleted in
function sdhci_tasklet_finish after a mmc request done, which will make
retuning timing never trigger again. This patch fixed this problem.
Signed-off-by: Aaron Lu <Aaron.Lu@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This bug has been introduced by:
d593411084
Author: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Date: Mon Jul 11 10:48:51 2011 +0300
iwlagn: simplify the bus architecture
Revert part of the buggy patch: dev_get_drvdata will now return
iwl_priv as it did before the patch.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit cc1a93e68f.
This fix introduced a bug: bad pointer in unload.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bug discovered by Jan Kara:
Finally, commit 1449032be1 returned back
the old IO submission code but apparently it forgot to return the old
handling of uninitialized buffers so we unconditionnaly call
block_write_full_page() without specifying end_io function. So AFAICS
we never convert unwritten extents to written in some cases. For
example when I mount the fs as: mount -t ext4 -o
nomblk_io_submit,dioread_nolock /dev/ubdb /mnt and do
int fd = open(argv[1], O_RDWR | O_CREAT | O_TRUNC, 0600);
char buf[1024];
memset(buf, 'a', sizeof(buf));
fallocate(fd, 0, 0, 16384);
write(fd, buf, sizeof(buf));
I get a file full of zeros (after remounting the filesystem so that
pagecache is dropped) instead of seeing the first KB contain 'a's.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
EXT4_IO_END_UNWRITTEN flag set and the increase of i_aiodio_unwritten
should be done simultaneously since ext4_end_io_nolock always clear
the flag and decrease the counter in the same time.
We don't increase i_aiodio_unwritten when setting
EXT4_IO_END_UNWRITTEN so it will go nagative and causes some process
to wait forever.
Part of the patch came from Eric in his e-mail, but it doesn't fix the
problem met by Michael actually.
http://marc.info/?l=linux-ext4&m=131316851417460&w=2
Reported-and-Tested-by: Michael Tokarev<mjt@tls.msk.ru>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
Flush inode's i_completed_io_list before calling ext4_io_wait to
prevent the following deadlock scenario: A page fault happens while
some process is writing inode A. During page fault,
shrink_icache_memory is called that in turn evicts another inode
B. Inode B has some pending io_end work so it calls ext4_ioend_wait()
that waits for inode B's i_ioend_count to become zero. However, inode
B's ioend work was queued behind some of inode A's ioend work on the
same cpu's ext4-dio-unwritten workqueue. As the ext4-dio-unwritten
thread on that cpu is processing inode A's ioend work, it tries to
grab inode A's i_mutex lock. Since the i_mutex lock of inode A is
still hold before the page fault happened, we enter a deadlock.
Also moves ext4_flush_completed_IO and ext4_ioend_wait from
ext4_destroy_inode() to ext4_evict_inode(). During inode deleteion,
ext4_evict_inode() is called before ext4_destroy_inode() and in
ext4_evict_inode(), we may call ext4_truncate() without holding
i_mutex lock. As a result, there is a race between flush_completed_IO
that is called from ext4_ext_truncate() and ext4_end_io_work, which
may cause corruption on an io_end structure. This change moves
ext4_flush_completed_IO and ext4_ioend_wait from ext4_destroy_inode()
to ext4_evict_inode() to resolve the race between ext4_truncate() and
ext4_end_io_work during inode deletion.
Signed-off-by: Jiaying Zhang <jiayingz@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
ext4_should_writeback_data() had an incorrect sequence of
tests to determine if it should return 0 or 1: in
particular, even in no-journal mode, 0 was being returned
for a non-regular-file inode.
This meant that, in non-journal mode, we would use
ext4_journalled_aops for directories, symlinks, and other
non-regular files. However, calling journalled aop
callbacks when there is no valid handle, can cause problems.
This would cause a kernel crash with Jan Kara's commit
2d859db3e4 ("ext4: fix data corruption in inodes with
journalled data"), because we now dereference 'handle' in
ext4_journalled_write_end().
I also added BUG_ONs to check for a valid handle in the
obviously journal-only aops callbacks.
I tested this running xfstests with a scratch device in
these modes:
- no-journal
- data=ordered
- data=writeback
- data=journal
All work fine; the data=journal run has many failures and a
crash in xfstests 074, but this is no different from a
vanilla kernel.
Signed-off-by: Curt Wohlgemuth <curtw@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
Some older Panasonic made camcorders (Panasonic AG-EZ30 and NV-DX110,
Grundig Scenos DLC 2000) reject requests with ack_busy_X if a request is
sent immediately after they sent a response to a prior transaction.
This causes firewire-core to fail probing of the camcorder with "giving
up on config rom for node id ...". Consequently, programs like kino or
dvgrab are unaware of the presence of a camcorder.
Such transaction failures happen also with the ieee1394 driver stack
(of the 2.4...2.6 kernel series until 2.6.36 inclusive) but with a lower
likelihood, such that kino or dvgrab are generally able to use these
camcorders via the older driver stack. The cause for firewire-ohci's or
firewire-core's worse behavior is not yet known. Gap count optimization
in firewire-core is not the cause. Perhaps the slightly higher latency
of transaction completion in the older stack plays a role. (ieee1394:
AR-resp DMA context tasklet -> packet completion ktread -> user process;
firewire-core: tasklet -> user process.)
This change introduces retries and delays after ack_busy_X into
firewire-core's Config ROM reader, such that at least firewire-core's
probing and /dev/fw* creation are successful. This still leaves the
problem that userland processes are facing transaction failures.
gscanbus's built-in retry routines deal with them successfully, but
neither kino's nor dvgrab's do ever succeed.
But at least DV capture with "dvgrab -noavc -card 0" works now. Live
video preview in kino works too, but not actual capture.
One way to prevent Configuration ROM reading failures in application
programs is to modify libraw1394 to synthesize read responses by means
of firewire-core's Configuration ROM cache. This would only leave
CMP and FCP transaction failures as a potential problem source for
applications.
Reported-and-tested-by: Thomas Seilund <tps@netmaster.dk>
Reported-and-tested-by: René Fritz <rene@colorcube.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
When the Manageability Engine (ME) is enabled on 82579, it periodically
accesses some MAC CSR registers. There is an arbiter in hardware which
prevents simultaneous access of these registers by the host software, i.e.
the driver. There is a hardware bug in the aribter that signals a host
access of the registers later than it actually happens. A write of the
Transmit or Receive Descriptor Tail register could result in an incorrect
value if the driver and ME perform simultaneous accesses which could result
in an access to an invalid memory address. This would return an
Unsupported Request which could hang the hardware. Workaround the issue by
checking the FWSM register bit24 which is set by ME before it accesses the
MAC CSR registers.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The MAC can drop short packets when the PHY detects noise on the line at
100Mbps due to a timing issue. Workaround the issue by increasing the PLL
counter so the PHY properly recognizes the synchronization pattern from the
MAC.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On 82577/8/9 in half-duplex when a received packet is passed from the PHY
to the MAC, if too many preamble octects are stripped from the packet
before arriving at the MAC, it can be misintrepeted as an in-band message
rather than an actual frame. For example, if the frame contents resembled
an interrupt request in-band message, it would trigger a false interrupt.
In most cases, the packet is just dropped.
By reducing the number of preamble octets stripped from the beginning of
the frame when passing it from the PHY to the MAC, the MAC will interpret
the frame properly.
An additional uses of the magic PHY_REG(770, 16) have been updated with a
define introduced with this patch.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to fix a memory leak found via code review for FCOE.
Specifically on DDP flows the SKBs were being dropped without being
recycled, freed, or given to the stack.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (30 commits)
USB: Serial: Add PID(0xF7C0) to FTDI SIO driver for a zeitcontrol-device
USB: Serial: Add device ID for Sierra Wireless MC8305
USB: Serial: Added device ID for Qualcomm Modem in Sagemcom's HiLo3G
usb/host/pci-quirks.c: correct annotation of `ehci_dmi_nohandoff_table'
USB: option driver: add PID for Vodafone-Huawei K4511
USB: option driver: add PID for Vodafone-Huawei K4510
USB: option driver: add PID for Vodafone-Huawei K3771
USB: option driver: add PID for Vodafone-Huawei K3770
usb: serial: ftdi_sio.c: For the FT232H FTDI_SIO_SET_BAUDRATE_REQUEST, index needs to be shifted too
usb/isp1760: Added missing call to usb_hcd_check_unlink_urb() during unlink
USB: EHCI: Fix test mode sequence
USB: ftdi_sio: fix minor typo in get_ftdi_divisor
USB: at91_udc: include linux/prefetch.h explicitly
USB: usb-storage: unusual_devs entry for ARM V2M motherboard.
usb/ehci-mxc: add missing inclusion of mach/hardware.h
USB: assign instead of equal in usbtmc.c
usb: renesas_usbhs: fixup usbhsg_for_each_uep 1st pos
usb: renesas_usbhs: fix DMA build by including dma-mapping.h
usb: gadget: net2272 - Correct includes
usb: musb: fix oops on musb_gadget_pullup
...
* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
zcache: Fix build error when sysfs is not defined
zcache: Use div_u64 for 64-bit division
staging:rts_pstor: fix thread synchronization flow
drivers:staging:solo6x10:add the missed slab.h
staging: zcache: include module.h for MODULE_LICENSE
drivers/staging/hv/blkvsc_drv.c: eliminate NULL pointer dereference
Staging: Add clk API note to nvec/TODO
drivers/staging/ath6kl/miscdrv/ar3kps/ar3kpsparser.c: adjust array index
staging: more missing slab.h inclusions
drivers/staging/solo6x10/p2m.c needs slab.h
drivers/staging/solo6x10/core.c needs slab.h
drivers/staging/dt3155v4l/dt3155v4l.c needs slab.h
drivers/staging/speakup/devsynth.c: fix "buffer size is not provably correct" error
Staging: iio: add some unlocks to raw_read() functions
staging: ft1000_proc needs asm/io.h for inw/outw on sparc
staging: rtl8192u: declare MODULE_FIRMWARE
gma500: Fix clashes with DRM updates
staging: zcache: module is GPL
staging: fix zcache building
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-tip:
x86-64: Rework vsyscall emulation and add vsyscall= parameter
x86-64: Wire up getcpu syscall
x86: Remove unnecessary compile flag tweaks for vsyscall code
x86-64: Add vsyscall:emulate_vsyscall trace event
x86-64: Add user_64bit_mode paravirt op
x86-64, xen: Enable the vvar mapping
x86-64: Work around gold bug 13023
x86-64: Move the "user" vsyscall segment out of the data segment.
x86-64: Pad vDSO to a page boundary
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: replace xfs_buf_geterror() with bp->b_error
xfs: Check the return value of xfs_buf_read() for NULL
"xfs: fix error handling for synchronous writes" revisited
xfs: set cursor in xfs_ail_splice() even when AIL was empty
xfs: Remove the macro XFS_BUFTARG_NAME
xfs: Remove the macro XFS_BUF_TARGET
xfs: Remove the macro XFS_BUF_SET_TARGET
Replace the macro XFS_BUF_ISPINNED with helper xfs_buf_ispinned
xfs: Remove the macro XFS_BUF_SET_PTR
xfs: Remove the macro XFS_BUF_PTR
xfs: Remove macro XFS_BUF_SET_START
xfs: Remove macro XFS_BUF_HOLD
xfs: Remove macro XFS_BUF_BUSY and family
xfs: Remove the macro XFS_BUF_ERROR and family
xfs: Remove the macro XFS_BUF_BFLAGS
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (32 commits)
ARM: mmp: Change the way we use timer 0 as clockevent timer.
ARM: mmp: Switch to using timer 1 as clocksource timer.
ARM: mmp: Also start timer 1 on boot.
ARM: pxa168/gplugd: free correct GPIO
ARM: pxa168/gplugd: get rid of mfp-gplugd.h
ARM: pxa: fix logic error in PJ4 iWMMXt handling
mach-sa1100: fix PCI build problem
omap: timer: Set dmtimer used as clocksource in autoreload mode
OMAP3: am3517crane: remove NULL board_mux from board file
arm: mach-omap2: mux: use kstrdup()
arch:arm:plat-omap:iovmm: remove unused variable 'va'
Update Nook Color machine 3284 to common Encore name
am3505/3517: Various platform defines for UART4
OMAP: hwmod: fix build break on non-OMAP4 multi-OMAP2 builds
OMAP: Fix linking error in twl-common.c for OMAP2/3/4 only builds
iMX: Fix build for iMX53
ARM: mx5: board-cpuimx51.c fixup irq_to_gpio() usage
OMAP2+: PM: SmartReflex: use put_sync_suspend for IRQ-safe disabling
OMAP3: beagle: don't touch omap_device internals
OMAP1: enable GENERIC_IRQ_CHIP
...
Use the move from Linux 2.6 to Linux 3.x as an excuse to kill the
annoying subdirectories in the XFS source code. Besides the large
amount of file rename the only changes are to the Makefile, a few
files including headers with the subdirectory prefix, and the binary
sysctl compat code that includes a header under fs/xfs/ from
kernel/.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Elder <aelder@sgi.com>
Fix up some #include directives in preparation for moving a few
header files out of xfs source subdirectories.
Note that "xfs_linux.h" also got its quoting convention for included
files switched.
Signed-off-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Since we just checked bp for NULL, it is ok to replace
xfs_buf_geterror() with bp->b_error in these places.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
Check the return value of xfs_buf_read() for NULL and return ENOMEM
if it is NULL. This is necessary in a few spots to avoid subsequent
code blindly dereferencing the null buffer pointer.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Alex Elder <aelder@sgi.com>
In each case, the freed data should be freed in the error handling code
as
well.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@exists@
local idexpression x;
statement S,S1;
expression E;
identifier fl;
expression *ptr != NULL;
@@
x = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...kfree(x)...+> }
when any
when != true x == NULL
x->fl
...>
(
if (x == NULL) S1
|
if (...) { ... when != x
when forall
(
return \(0\|<+...x...+>\|ptr\);
|
* return ...;
)
}
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sound/soc/codecs/wm8750.c:784:2: warning: missing braces around initializer
sound/soc/codecs/wm8750.c:784:2: warning: (near initialization for ‘wm8750_spi_ids[2].name’)
It's because struct spi_device_id.name is a char array, not a pointer,
while the driver initializes explicitly with 0.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Jiri Pirko