- Cleanup BKOPS support
- Introduce MMC_CAP_SYNC_RUNTIME_PM
- slot-gpio: Delete legacy slot GPIO handling
MMC host:
- alcor: Add new mmc host driver for Alcor Micro PCI based cardreader
- bcm2835: Several improvements to better recover from errors
- jz4740: Rework and fixup pre|post_req support
- mediatek: Add support for SDIO IRQs
- meson-gx: Improve clock phase management
- meson-gx: Stop descriptor on errors
- mmci: Complete the sbc error path by sending a stop command
- renesas_sdhi/tmio: Fixup reset/resume operations
- renesas_sdhi: Add support for r8a774c0 and R7S9210
- renesas_sdhi: Whitelist R8A77990 SDHI
- renesas_sdhi: Fixup eMMC HS400 compatibility issues for H3 and M3-W
- rtsx_usb_sdmmc: Re-work card detection/removal support
- rtsx_usb_sdmmc: Re-work runtime PM support
- sdhci: Fix timeout loops for some variant drivers
- sdhci: Improve support for error handling due to failing commands
- sdhci-acpi/pci: Disable LED control for Intel BYT-based controllers
- sdhci_am654: Add new SDHCI variant driver to support TI's AM654 SOCs
- sdhci-of-esdhc: Add support for eMMC HS400 mode
- sdhci-omap: Fixup reset support
- sdhci-omap: Workaround errata regarding SDR104/HS200 tuning failures
- sdhci-msm: Fixup sporadic write transfers issues for SDR104/HS200
- sdhci-msm: Fixup dynamical clock gating issues
- various: Complete converting all hosts into using slot GPIO descriptors
Other:
- Move GPIO mmc platform data for mips/sh/arm to GPIO descriptors
- Add new Alcor Micro cardreader PCI driver
- Support runtime power management for memstick rtsx_usb_ms driver
- Use USB remote wakeups for card detection for rtsx_usb misc driver
-----BEGIN PGP SIGNATURE-----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=mB5P
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"This time, this pull request contains changes crossing subsystems and
archs/platforms, which is mainly because of a bigger modernization of
moving from legacy GPIO to GPIO descriptors for MMC (by Linus
Walleij).
Additionally, once again, I am funneling changes to
drivers/misc/cardreader/* and drivers/memstick/* through my MMC tree,
mostly due to that we lack a maintainer for these.
Summary:
MMC core:
- Cleanup BKOPS support
- Introduce MMC_CAP_SYNC_RUNTIME_PM
- slot-gpio: Delete legacy slot GPIO handling
MMC host:
- alcor: Add new mmc host driver for Alcor Micro PCI based cardreader
- bcm2835: Several improvements to better recover from errors
- jz4740: Rework and fixup pre|post_req support
- mediatek: Add support for SDIO IRQs
- meson-gx: Improve clock phase management
- meson-gx: Stop descriptor on errors
- mmci: Complete the sbc error path by sending a stop command
- renesas_sdhi/tmio: Fixup reset/resume operations
- renesas_sdhi: Add support for r8a774c0 and R7S9210
- renesas_sdhi: Whitelist R8A77990 SDHI
- renesas_sdhi: Fixup eMMC HS400 compatibility issues for H3 and M3-W
- rtsx_usb_sdmmc: Re-work card detection/removal support
- rtsx_usb_sdmmc: Re-work runtime PM support
- sdhci: Fix timeout loops for some variant drivers
- sdhci: Improve support for error handling due to failing commands
- sdhci-acpi/pci: Disable LED control for Intel BYT-based controllers
- sdhci_am654: Add new SDHCI variant driver to support TI's AM654 SOCs
- sdhci-of-esdhc: Add support for eMMC HS400 mode
- sdhci-omap: Fixup reset support
- sdhci-omap: Workaround errata regarding SDR104/HS200 tuning failures
- sdhci-msm: Fixup sporadic write transfers issues for SDR104/HS200
- sdhci-msm: Fixup dynamical clock gating issues
- various: Complete converting all hosts into using slot GPIO descriptors
Other:
- Move GPIO mmc platform data for mips/sh/arm to GPIO descriptors
- Add new Alcor Micro cardreader PCI driver
- Support runtime power management for memstick rtsx_usb_ms driver
- Use USB remote wakeups for card detection for rtsx_usb misc driver"
* tag 'mmc-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (99 commits)
mmc: mediatek: Add MMC_CAP_SDIO_IRQ support
mmc: renesas_sdhi_internal_dmac: Whitelist r8a774c0
dt-bindings: mmc: renesas_sdhi: Add r8a774c0 support
mmc: core: Cleanup BKOPS support
mmc: core: Drop redundant check in mmc_send_hpi_cmd()
mmc: sdhci-omap: Workaround errata regarding SDR104/HS200 tuning failures (i929)
dt-bindings: sdhci-omap: Add note for cpu_thermal
mmc: sdhci-acpi: Disable LED control for Intel BYT-based controllers
mmc: sdhci-pci: Disable LED control for Intel BYT-based controllers
mmc: sdhci: Add quirk to disable LED control
mmc: mmci: add variant property to set command stop bit
misc: alcor_pci: fix spelling mistake "invailid" -> "invalid"
mmc: meson-gx: add signal resampling
mmc: meson-gx: align default phase on soc vendor tree
mmc: meson-gx: remove useless lock
mmc: meson-gx: make sure the descriptor is stopped on errors
mmc: sdhci_am654: Add Initial Support for AM654 SDHCI driver
dt-bindings: mmc: sdhci-of-arasan: Add deprecated message for AM65
dt-bindings: mmc: sdhci-am654: Document bindings for the host controllers on TI's AM654 SOCs
mmc: sdhci-msm: avoid unused function warning
...
This has been a busy release for the regmap-irq code, there's several
new features been added, including an API cleanup for how we specify
types that affected one existing driver (gpio-max77620):
- Support for hardware that flags rising and falling edges on separate
status bits from Bartosz Golaszewski.
- Support for explicitly clearing interrupts before unmasking from
Bartosz Golaszewski.
- Support for level triggered IRQs from Matti Vaittinen.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlwhMAUTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0MI0B/9K27CbnGskQHZqWQxcFg1iVck/ZPty
kqfIGYDafvqT2TaVL+tFM8kzjLB3dMuV3cbywppq6+pzEvR/BDzhUKbskNPSLjUo
zNxKbwiBJPFLqlZORhzncuPcpRvrGGp120B+gr7lKOJgSG73u6bvOEzYaZbJzPb8
KiKo5oFqB/wpj3Gw243RjYE+7yaM/i7IAR/mW//RoKMWYERv6koR+GL0jgalib4d
mezH0ipO/SGDPorVOeUWxm/mlUYhEbitTa9+BtAYC/0+Nba1ns1p6dduchhXrAA0
/cOCHHVypPSiKLxjth+FA20CbemALb6swoZztVWYNS+0jJ2/bkh1rCoB
=aiDq
-----END PGP SIGNATURE-----
Merge tag 'regmap-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"This has been a busy release for the regmap-irq code, there's several
new features been added, including an API cleanup for how we specify
types that affected one existing driver (gpio-max77620):
- Support for hardware that flags rising and falling edges on
separate status bits from Bartosz Golaszewski.
- Support for explicitly clearing interrupts before unmasking from
Bartosz Golaszewski.
- Support for level triggered IRQs from Matti Vaittinen"
* tag 'regmap-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: irq: add an option to clear status registers on unmask
regmap: regmap-irq/gpio-max77620: add level-irq support
regmap: regmap-irq: Remove default irq type setting from core
regmap: debugfs: convert to DEFINE_SHOW_ATTRIBUTE
regmap: rbtree: convert to DEFINE_SHOW_ATTRIBUTE
regmap: irq: handle HW using separate rising/falling edge interrupts
regmap: add a new macro:REGMAP_IRQ_REG_LINE(_id, _reg_bits)
This has been a very busy release for the core, some fixes, one large new
feature and a big bit of refactoring to update the GPIO API:
- Support for coupled regulators from Dmitry Osipenko based on a prior
attempt by Maciej Purski, allowing us to handle situations where the
voltages on two regulators can't be too far apart from each other.
- Conversion of the GPIO support in both drivers and the core to use
GPIO descriptors rather than numbers, part of the overall project to
remove GPIO numbers.
- Support for standby mode suspend states from Andrei Stefanescu.
- New drivers for Allwinner AXP209, Cirrus Logic Lochnagar and
Microchip MPC16502.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlwhKkcTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0DFfB/91/ECmybKTP+RvwUTZ0rrqFFs2C9Vl
76vH242exyJuzv44inWi9gOcXFDn7c9hf7Vl4Jd5UVP53Nzm5I8ZwExQsxax9BsN
hltlX01UpRAmHNkMNrnJH6YAntD3EicYGSUDjohkWItIDqpMAjhWpx/yGXTEjBir
gvkV51bF3qAYQe0g6MmK3KeVw96QPNjUhoPbsqbpaXaF6fmyOVzMiFrffJGmUAyM
J5qRv3OhsZiZy2/zxNLkUI6y4XKDEaFJ3RhSKoUwItGyKQt2saXMoJGyEEWm2b6X
coTm0ZQk+EU+b659lDHErTM4YUx7p7tQt3VM09NoMD8B261TdZ0y99Oh
=8Rxt
-----END PGP SIGNATURE-----
Merge tag 'regulator-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"This has been a very busy release for the core, some fixes, one large
new feature and a big bit of refactoring to update the GPIO API:
- Support for coupled regulators from Dmitry Osipenko based on a
prior attempt by Maciej Purski, allowing us to handle situations
where the voltages on two regulators can't be too far apart from
each other.
- Conversion of the GPIO support in both drivers and the core to use
GPIO descriptors rather than numbers, part of the overall project
to remove GPIO numbers.
- Support for standby mode suspend states from Andrei Stefanescu.
- New drivers for Allwinner AXP209, Cirrus Logic Lochnagar and
Microchip MPC16502"
* tag 'regulator-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (90 commits)
regulator: tps65910: fix a missing check of return value
regulator: mcp16502: Select REGMAP_I2C to fix build error
regulator: convert to DEFINE_SHOW_ATTRIBUTE
regulator: mcp16502: Fix missing n_voltages setting
regulator: mcp16502: Use #ifdef CONFIG_PM_SLEEP around mcp16502_suspend/resume_noirq
regulator: mcp16502: code cleanup
regulator: act8945a-regulator: make symbol act8945a_pm static
drivers/regulator: fix a missing check of return value
regulator: act8945a-regulator: fix 'defined but not used' compiler warning
regulator: axp20x: fix set_ramp_delay for AXP209/dcdc2
regulator: mcp16502: add support for suspend
mfd: axp20x: use explicit bit defines
mfd: axp20x: Clean up included headers
regulator: dts: enable soft-start and ramp delay for the OLinuXino Lime2
dt-bindings: mfd: axp20x: Add software based soft_start for AXP209 LDO3
regulator: axp20x: add software based soft_start for AXP209 LDO3
dt-bindings: mfd: axp20x: add support for regulator-ramp-delay for AXP209
regulator: axp20x: add support for set_ramp_delay for AXP209
mfd: axp20x: name voltage ramping define properly
regulator: mcp16502: add regulator driver for MCP16502
...
This driver clearly needs OF_GPIO so depend on it.
Fixes a build error.
Cc: Andrei Stefanescu <Andrei.Stefanescu@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- ACPI IRQ request deferral
- OMAP: revert deferred wakeup quirk
- MAX7301: fix DMA safe memory handling
- MVEBU: selective probe failure on missing clk
-----BEGIN PGP SIGNATURE-----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=+Iw2
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.20-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Hopefully last round of GPIO fixes.
The ACPI patch is pretty important for some laptop users, the rest is
driver-specific for embedded (mostly ARM) systems.
I took out one ACPI patch that wasn't critical enough because I
couldn't justify sending it at this point, and that is why the commit
date is today, but the patches have been in linux-next.
Sorry for not sending some of them earlier :(
Notice that we have a co-maintainer for GPIO now, Bartosz Golaszewski,
and he might jump in and make some pull requests at times when I am
off.
Summary:
- ACPI IRQ request deferral
- OMAP: revert deferred wakeup quirk
- MAX7301: fix DMA safe memory handling
- MVEBU: selective probe failure on missing clk"
* tag 'gpio-v4.20-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: mvebu: only fail on missing clk if pwm is actually to be used
gpio: max7301: fix driver for use with CONFIG_VMAP_STACK
gpio: gpio-omap: Revert deferred wakeup quirk handling for regressions
gpiolib-acpi: Only defer request_irq for GpioInt ACPI event handlers
This patch adds a driver for Cadence GPIO controller.
It can be enabled with GPIO_CADENCE Kconfig option.
It uses generic GPIO infrastructure and works
as an interrupt controller.
At the moment it only supports level sensitive irqs.
Signed-off-by: Jan Kotas <jank@cadence.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Variable err is defined but never used. Remove it. Cleans up warning:
warning: unused variable ‘err’ [-Wunused-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Calling readl directly instead of going through another function that
results in the same result to remove some overhead. I didn't try to
measure the performance gain, but IMHO there is little benefit from
abstracting a GPIO register access in the GPIO driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove duplicated assignment statement from aspeed_gpio_probe() function.
Signed-off-by: Tao Ren <taoren@fb.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PIOBU pins do not lose their voltage during Backup/Self-refresh.
This patch adds a simple GPIO controller for them and a
maintainer for the driver.
This driver adds support for using the pins as GPIO
offering the possibility to read/set the voltage.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio IP on Armada 370 at offset 0x18180 has neither a clk nor pwm
registers. So there is no need for a clk as the pwm isn't used anyhow.
So only check for the clk in the presence of the pwm registers. This fixes
a failure to probe the gpio driver for the above mentioned gpio device.
Fixes: 757642f9a5 ("gpio: mvebu: Add limited PWM support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
spi_read() and spi_write() require DMA-safe memory. When
CONFIG_VMAP_STACK is selected, those functions cannot be used
with buffers on stack.
This patch replaces calls to spi_read() and spi_write() by
spi_write_then_read() which doesn't require DMA-safe buffers.
Fixes: 0c36ec3147 ("gpio: gpio driver for max7301 SPI GPIO expander")
Cc: <stable@vger.kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit ec0daae685 ("gpio: omap: Add level wakeup handling for omap4
based SoCs") attempted to fix omap4 GPIO wakeup handling as it was
blocking deeper SoC idle states. However this caused a regression for
GPIOs during runtime having over second long latencies for Ethernet
GPIO interrupt as reportedy by Russell King <rmk+kernel@armlinux.org.uk>.
Let's fix this issue by doing a partial revert of the breaking commit.
We still want to keep the quirk handling around as it is also used for
OMAP_GPIO_QUIRK_IDLE_REMOVE_TRIGGER.
The real fix for omap4 GPIO wakeup handling involves fixes for
omap_set_gpio_trigger() and omap_gpio_unmask_irq() and will be posted
separately. And we must keep the wakeup bit enabled during runtime
because of module doing clock autogating with autoidle configured.
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Fixes: ec0daae685 ("gpio: omap: Add level wakeup handling for omap4
based SoCs")
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add level active IRQ support to regmap-irq irqchip. Change breaks
existing regmap-irq type setting. Convert the existing drivers which
use regmap-irq with trigger type setting (gpio-max77620) to work
with this new approach. So we do not magically support level-active
IRQs on gpio-max77620 - but add support to the regmap-irq for chips
which support them =)
We do not support distinguishing situation where HW supports rising
and falling edge detection but not both. Separating this would require
inventing yet another flags for IRQ types.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The device tree bindings for the MMC card detect and
write protect lines specify that these should be active
low unless "cd-inverted" or "wp-inverted" has been
specified.
However that is not how the kernel code has worked. It
has always respected the flags passed to the phandle in
the device tree, but respected the "cd-inverted" and
"wp-inverted" flags such that if those are set, the
polarity will be the inverse of that specified in the
device tree.
Switch to behaving like the old code did and fix the
regression.
Fixes: 81c85ec15a ("gpio: OF: Parse MMC-specific CD and WP properties")
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Select REGMAP_I2C in Kconfig, since the driver now depends on regmap
and this was missing, thus breaking build on various systems.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We're getting a reference RPi's firmware node in order to be able to
communicate with it's driver. We should decrease the reference count on
the dt node after being done with it.
Fixes: a98d90e7d5 ("gpio: raspberrypi-exp: Driver for RPi3 GPIO expander via mailbox service")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of using the name directly from the I2C client
to name the gpio_chip, use dev_name() on the client->dev,
so we get the sometimes more unique device name, as I2C has
a mechanism for naming its devices explicitly in e.g.
board data.
This is a prerequisite for being able to reference
uniquely any I2C GPIO expander defined in a board file
when setting up GPIO descriptor tables.
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is possible that the PCA953x is powered down during suspend.
Use regmap cache to assure the registers in the PCA953x are in
line with the driver state after resume.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Drop pca953x_write_single() which is used in one place.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace the ad-hoc reg_output output register caching with generic
regcache cache. Drop pca953x_write_single() which is no longer used.
This reduces code duplication.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert the driver to use regmap to access the chips. Due to the convoluted
register mapping scheme, implement read/write/volatile check functions that
untangle the mess and perform check accordingly. This patch does not zap the
internal register cache of the PCA953x driver, nor does it push the regmap
access down into the gpiochip accessors to simplify the review. All that is
in subsequent patches.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of having the I2C register calculation function spread across
multiple accessor functions, pull it out into a single function which
returns the adjusted register address.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ad-hoc i2c block write can be replaced by standard register accessor
function, which correctly handles all the chip details and differences.
Do so to simplify the code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PCA957x and PCA953x init functions are almost the same, except for
the different register mapping and one extra write to BKEN register in
case of PCA957x. Factor out the common code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
At this point, the pca953x_{read,write}_regs_mul() can read single bank
PCA953x GPIO chips as well. Merge the _8 and _mul functions together to
simplify the code a bit.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
At this point, these two functions only differ in whether they do or do not
set the address increment bit. The 16 GPIO case does not need to set the AI
bit, except for PCA9575 on write, while the 24 GPIO and more case does set
the AI bit always. Merge these two functions together to simplify the code
a bit.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
At this point, these two functions only differ in whether they do or do not
set the address increment bit on PCA9575. Merge these two functions together
to simplify the code a bit.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The multi-byte IO on various pca953x chips requires the auto-increment bit,
while other chips toggle the LSbit automatically. Note that LSbit toggling
only alternates between two registers during the IO, it is not the same as
address auto-increment. The driver currently assumes that #gpios > 16 implies
auto-increment, while #gpios <= 16 implies LSbit toggling. This is incorrect
at there are chips with 16 GPIOs which require the auto-increment bit.
The PCA9575, according to NXP datasheet rev. 4.2 from 16 April 2015, section
7.3 Command Register, the bit 7 in command register is the auto-increment
bit, which allows programming multiple registers sequentially.
Set this bit both in pca953x_gpio_set_multiple(), where it fixes the multi
register programming, and in pca957x_write_regs_16(), where is simplifies
the function. In fact, the pca957x_write_regs_16() now looks rather similar
to pca953x_write_regs_24() and pca953x_write_regs_16(), which is intended
for subsequent patches.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PCAL_PINCTRL_MASK is too large. The extended register block on
PCAL6524, which is the largest chip with this block, has the block
limited to address range 0x40..0x7f. This is because the bit 7 in
the command register is used for the Address Increment functionality.
Trim the mask to 0x60 to match the datasheet and to prevent accidental
overwrite of the AI bit.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The bank_shift = fls(...) code was duplicated in the driver 5 times,
pull it into separate function.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The IRQ core code refers to the interrupt type by that name, whereas the
term flow is almost never used. Some GPIO controllers use the term
flow_type, but it is most consistent to just go with the IRQ core
terminology.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use managed resource allocation in pch and sodaville drivers.
Switch to use for_each_set_bit() in IRQ handlers.
Headers clean up.
Sort headers in inclusion block alphabetically for better maintenance.
Convert to SPDX identifier and fixing MODULE_LICENSE() when appropriate.
Additional format fixes to rectify debug and message printing.
There is a commit which had been applied to v4.20-rc4, that's why dup.
- c3bc3ff9e8 MAINTAINERS: Do maintain Intel GPIO drivers via separate tree
The following is an automated git shortlog grouped by driver:
ich:
- Convert to use SPDX identifier
- Sort headers alphabetically
- Join string literals back
- Convert pr_<level> to dev_<level>
- Switch to use struct device instead of platform_device
- Simplify error handling in ichx_write_bit()
intel-mid:
- Convert to use SPDX identifier
- Remove linux/module.h and sort headers
lynxpoint:
- Convert to use SPDX identifier
- Remove linux/init.h and sort headers
- Use for_each_set_bit() in IRQ handler
MAINTAINERS:
- Do maintain Intel GPIO drivers via separate tree
merrifield:
- Convert to use SPDX identifier
- Remove linux/init.h
pch:
- Convert to use SPDX identifier
- Sort headers alphabetically
- Remove duplicate assignments
- Remove redundant __func__ from debug print
- Use for_each_set_bit() in IRQ handler
- Convert to dev_pm_ops
- Convert to use managed functions pcim_* and devm_*
sch:
- Convert to use SPDX identifier
- Remove linux/init.h and sort headers
sodaville:
- Convert to use SPDX identifier
- Sort headers alphabetically
- Use for_each_set_bit() in IRQ handler
- Convert to use managed functions pcim_* and devm_*
-----BEGIN PGP SIGNATURE-----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=5W0M
-----END PGP SIGNATURE-----
Merge tag 'intel-gpio-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel into devel
intel-gpio for v4.21-1
Use managed resource allocation in pch and sodaville drivers.
Switch to use for_each_set_bit() in IRQ handlers.
Headers clean up.
Sort headers in inclusion block alphabetically for better maintenance.
Convert to SPDX identifier and fixing MODULE_LICENSE() when appropriate.
Additional format fixes to rectify debug and message printing.
There is a commit which had been applied to v4.20-rc4, that's why dup.
- c3bc3ff9e8 MAINTAINERS: Do maintain Intel GPIO drivers via separate tree
The following is an automated git shortlog grouped by driver:
ich:
- Convert to use SPDX identifier
- Sort headers alphabetically
- Join string literals back
- Convert pr_<level> to dev_<level>
- Switch to use struct device instead of platform_device
- Simplify error handling in ichx_write_bit()
intel-mid:
- Convert to use SPDX identifier
- Remove linux/module.h and sort headers
lynxpoint:
- Convert to use SPDX identifier
- Remove linux/init.h and sort headers
- Use for_each_set_bit() in IRQ handler
MAINTAINERS:
- Do maintain Intel GPIO drivers via separate tree
merrifield:
- Convert to use SPDX identifier
- Remove linux/init.h
pch:
- Convert to use SPDX identifier
- Sort headers alphabetically
- Remove duplicate assignments
- Remove redundant __func__ from debug print
- Use for_each_set_bit() in IRQ handler
- Convert to dev_pm_ops
- Convert to use managed functions pcim_* and devm_*
sch:
- Convert to use SPDX identifier
- Remove linux/init.h and sort headers
sodaville:
- Convert to use SPDX identifier
- Sort headers alphabetically
- Use for_each_set_bit() in IRQ handler
- Convert to use managed functions pcim_* and devm_*
Before things go out of hand, make it possible to pass
flags when requesting "own" descriptors from a gpio_chip.
This is necessary if the chip wants to request a GPIO with
active low semantics, for example.
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Roger Quadros <rogerq@ti.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a function named devm_gpiod_unhinge() that removes
the resource management from a GPIO descriptor.
I am not sure if this is the best anglosaxon name for the
function, no other managed resources have an equivalent
currently, but I chose "unhinge" as the closest intuitive
thing I could imagine that fits Rusty Russell's API design
criterions "the obvious use is the correct one" and
"the name tells you how to use it".
The idea came out of a remark from Mark Brown that it should
be possible to handle over management of a resource from
devres to the regulator core, and indeed we can do that.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When we get a nonexeclusive GPIO descriptor using managed
resources, we should only add it to the list of managed
resources once: on the first user. Augment the
devm_gpiod_get_index() and devm_gpiod_get_from_of_node()
calls to account for this by checking if the descriptor
is already resource managed before we proceed to allocate
a new resource management struct.
Fixes: b0ce7b29bf ("regulator/gpio: Allow nonexclusive GPIO access")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This makes gpiod_get_from_of_node() respect the
GPIOD_FLAGS_BIT_NONEXCLUSIVE flag which is especially
nice when getting regulator GPIOs right out of device
tree nodes.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: b0ce7b29bf ("regulator/gpio: Allow nonexclusive GPIO access")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This function already exist inside gpiolib, we were just
reluctant to make it available to the kernel at large as
the devm_* seemed to be enough for anyone.
However we found out that regulators need to do their own
lifecycle/refcounting on GPIO descriptors and explicitly
call gpiod_put() when done with a descriptor, so export
this function so we can hand the refcounting over to the
regulator core for these descriptors after retrieveal.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The problem is reported for allmodconfig build setup:
ERROR: "irq_chip_retrigger_hierarchy" [drivers/gpio/gpio-lpc18xx.ko] undefined!
make[2]: *** [scripts/Makefile.modpost:92: __modpost] Error 1
make[1]: *** [Makefile:1271: modules] Error 2
My testing in runtime shows that it is sufficient to remove .irq_retrigger
callback, which is assigned to unexported irq_chip_retrigger_hierarchy()
function, I did't observe any regressions, and thus apparently it is a
better fix rather than exporting the function defined in kernel/irq/chip.c
(see commit 52b2a05fa7 ("genirq: Export IRQ functions for module use"))
or sticking the GPIO controller driver build to built-in option only.
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 5ddabfe8d3 ("gpio: lpc18xx: add GPIO pin interrupt controller support")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There is no need to include linux/init.h when at the same time
we include linux/module.h.
Remove redundant inclusion.
While here, sort header block alphabetically for easy maintenance.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There is no need to include linux/init.h when at the same time
we include linux/module.h.
Remove redundant inclusion.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There is no need to include linux/init.h when at the same time
we include linux/module.h.
Remove redundant inclusion.
While here, sort header block alphabetically for easy maintenance.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There is no need to include linux/module.h when at the same time
we include linux/init.h.
Remove redundant inclusion.
While here, remove no-op macro and sort header block alphabetically
for easy maintenance.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
dev_dbg includes the function name & line number by default when dynamic
debugging is enabled. Hence __func__ is redundant here and removed.
Do the same for any messages in ->probe() since it doesn't make sense.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
For easy grepping on debug purposes join string literals back in the
messages.
While here, fix spelling typo.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There is no need to have a pointer to struct platform_device.
Instead, switch to use struct device one.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Simplify error handling in ichx_write_bit() and propagate its error code
to the caller.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This simplifies and standardizes the AB IRQ handler by using
the for_each_set_bit() library function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This simplifies and standardizes the AB IRQ handler by using
the for_each_set_bit() library function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
checkpatch.pl suggests to use SPDX license tag. I am happy to
follow it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Zynq's gpios can be configured by the bootloader. But Linux will
erroneously report all gpios as inputs unless we implement
get_direction().
Signed-off-by: Brandon Maier <Brandon.Maier@collins.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 78d3a92edb ("gpiolib-acpi: Register GpioInt ACPI event handlers
from a late_initcall") deferred the entire acpi_gpiochip_request_interrupt
call for each event resource.
This means it also delays the gpiochip_request_own_desc(..., "ACPI:Event")
call. This is a problem if some AML code reads the GPIO pin before we
run the deferred acpi_gpiochip_request_interrupt, because in that case
acpi_gpio_adr_space_handler() will already have called
gpiochip_request_own_desc(..., "ACPI:OpRegion") causing the call from
acpi_gpiochip_request_interrupt to fail with -EBUSY and we will fail to
register an event handler.
acpi_gpio_adr_space_handler is prepared for acpi_gpiochip_request_interrupt
already having claimed the pin, but the other way around does not work.
One example of a problem this causes, is the event handler for the OTG
ID pin on a Prowise PT301 tablet not registering, keeping the port stuck
in whatever mode it was in during boot and e.g. only allowing charging
after a reboot.
This commit fixes this by only deferring the request_irq call and the
initial run of edge-triggered IRQs instead of deferring all of
acpi_gpiochip_request_interrupt.
Cc: stable@vger.kernel.org
Fixes: 78d3a92edb ("gpiolib-acpi: Register GpioInt ACPI event ...")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The change adds support of LPC18xx/LPC43xx GPIO pin interrupt controller
block within SoC GPIO controller. The new interrupt controller driver
allows to configure and capture edge or level interrupts on 8 arbitrary
selectedinput GPIO pins, and lift the signals to be reported as NVIC rising
edge interrupts. Configuration of a particular GPIO pin to serve as
interrupt and its mapping to an interrupt on NVIC is done by SCU pin
controller, for more details see description of 'nxp,gpio-pin-interrupt'
device tree property of a GPIO pin [1].
From LPC18xx and LPC43xx User Manuals the GPIO controller consists of
the following blocks:
* GPIO pin interrupt block at 0x40087000, this change adds its support,
* GPIO GROUP0 interrupt block at 0x40088000,
* GPIO GROUP1 interrupt block at 0x40089000,
* GPIO port block at 0x400F4000, it is supported by the original driver.
While all 4 sub-controller blocks have their own I/O addresses, moreover
all 3 interrupt blocks are APB0 peripherals and high-speed GPIO block is
an AHB slave, according to the hardware manual the GPIO controller is
seen as a single block, and 4 sub-controllers have the shared reset signal
RGU #28 and clock to register interface CLK_CPU_GPIO on CCU1.
Likely support of two GPIO group interrupt blocks won't be added in short
term, because the mechanism to mask several interrupt sources is not well
defined.
[1] Documentation/devicetree/bindings/pinctrl/nxp,lpc1850-scu.txt
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a non-functional change, it simplifies multiple access to
'struct device' pointer derived from a platform device pointer,
the new local variable will also be used in the following changes.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace GPLv2 header with the SPDX identifier.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The error cases of mediatek_gpio_bank_probe() would go unnoticed (except
for the dev_err() messages). The probe function should return an error
if one of the banks failed to initialize properly indicated by
not returning non-0.
Fixes: 4ba9c3afda ("gpio: mt7621: Add a driver for MT7621")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
kasprintf() may return NULL on failure of internal allocation thus the
assigned label is not safe if not explicitly checked. On error
mediatek_gpio_bank_probe() returns negative values so -ENOMEM in the
(unlikely) failure case should be fine here.
Fixes: 4ba9c3afda ("gpio: mt7621: Add a driver for MT7621")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The change simplifies dereferences to the mediated struct device, also
it allows to limit the scope of the platform device usage to probe and
remove functions only.
Non-functional change.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This simplifies and standardizes the AB IRQ handler by using
the for_each_set_bit() library function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Convert the legacy system PM callbacks to new ones. Meanwhile, remove the
redundant calls to the PCI for changing a power state since it's done by bus
code.
While here, remove weird indentation with backslash in use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Volume is a little higher than usual due to a set of gpio fixes for
Davinci platforms that's been around a while, still seemed appropriate
to not hold off until next merge window.
Besides that it's the usual mix of minor fixes, mostly corrections of
small stuff in device trees.
Major stability-related one is the removal of a regulator from DT on
Rock960, since DVFS caused undervoltage. I expect it'll be restored once
they figure out the underlying issue.
-----BEGIN PGP SIGNATURE-----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=m41T
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Volume is a little higher than usual due to a set of gpio fixes for
Davinci platforms that's been around a while, still seemed appropriate
to not hold off until next merge window.
Besides that it's the usual mix of minor fixes, mostly corrections of
small stuff in device trees.
Major stability-related one is the removal of a regulator from DT on
Rock960, since DVFS caused undervoltage. I expect it'll be restored
once they figure out the underlying issue"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
MAINTAINERS: Remove unused Qualcomm SoC mailing list
ARM: davinci: dm644x: set the GPIO base to 0
ARM: davinci: da830: set the GPIO base to 0
ARM: davinci: dm355: set the GPIO base to 0
ARM: davinci: dm646x: set the GPIO base to 0
ARM: davinci: dm365: set the GPIO base to 0
ARM: davinci: da850: set the GPIO base to 0
gpio: davinci: restore a way to manually specify the GPIO base
ARM: davinci: dm644x: define gpio interrupts as separate resources
ARM: davinci: dm355: define gpio interrupts as separate resources
ARM: davinci: dm646x: define gpio interrupts as separate resources
ARM: davinci: dm365: define gpio interrupts as separate resources
ARM: davinci: da8xx: define gpio interrupts as separate resources
ARM: dts: at91: sama5d2: use the divided clock for SMC
ARM: dts: imx51-zii-rdu1: Remove EEPROM node
ARM: dts: rockchip: Remove @0 from the veyron memory node
arm64: dts: rockchip: Fix PCIe reset polarity for rk3399-puma-haikou.
arm64: dts: qcom: msm8998: Reserve gpio ranges on MTP
arm64: dts: sdm845-mtp: Reserve reserved gpios
arm64: dts: ti: k3-am654: Fix wakeup_uart reg address
...
This makes the error handling much more simpler than open-coding everything
and in addition makes the probe function smaller an tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This makes the error handling much more simpler than open-coding everything
and in addition makes the probe function smaller an tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
When retrieveing CD (card detect) and WP (write protect)
GPIO handles from the device tree, make sure to assign
them active low by default unless the "cd-inverted" or
"wp-inverted" properties are set. These properties mean
that respective signal is active HIGH since the SDHCI
specification stipulates that this kind of signals
should be treated as active LOW.
If the twocell GPIO flag is also specified as active
low, well that's nice and we will silently ignore the
tautological specification.
If however the GPIO line is specified as active low
in the GPIO flasg cell and "cd-inverted" or "wp-inverted"
is also specified, the latter takes precedence and we
print a warning.
The current effect on the MMC slot-gpio core are as
follows:
For CD GPIOs: no effect. The current code in
mmc/core/host.c calls mmc_gpiod_request_cd() with
the "override_active_level" argument set to true,
which means that whatever the GPIO descriptor
thinks about active low/high will be ignored, the
core will use the MMC_CAP2_CD_ACTIVE_HIGH to keep
track of this and reads the raw value from the
GPIO descriptor, totally bypassing gpiolibs inversion
semantics. I plan to clean this up at a later point
passing the handling of inversion semantics over
to gpiolib, so this patch prepares the ground for
that.
Fow WP GPIOs: this is probably fixing a bug, because
the code in mmc/core/host.c calls mmc_gpiod_request_ro()
with the "override_active_level" argument set to false,
which means it will respect the inversion semantics of
the gpiolib and ignore the MMC_CAP2_RO_ACTIVE_HIGH
flag for everyone using this through device tree.
However the code in host.c confusingly goes to great
lengths setting up the MMC_CAP2_RO_ACTIVE_HIGH flag
from the GPIO descriptor and by reading the "wp-inverted"
property of the node. As far as I can tell this is all
in vain and the inversion is broken: device trees that
use "wp-inverted" do not work as intended, instead the
only way to actually get inversion on a line is by
setting the second cell flag to GPIO_ACTIVE_HIGH (which
will be the default) or GPIO_ACTIVE_LOW if they want
the proper MMC semantics. Presumably all device trees do
this right but we need to parse and handle this properly.
Cc: linux-mmc@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 587f7a694f ("gpio: davinci: Use dev name for label and
automatic base selection") broke the network support in legacy boot
mode for da850-evm since we can no longer request the MDIO clock GPIO.
Other boards may be broken too, which I haven't tested.
The problem is in the fact that most board files still use the legacy
GPIO API where lines are requested by numbers rather than descriptors.
While this should be fixed eventually, in order to unbreak the board
for now - provide a way to manually specify the GPIO base in platform
data.
Fixes: 587f7a694f ("gpio: davinci: Use dev name for label and automatic base selection")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
It's easy to verify that the change of drivers/gpio/gpiolib-of.c license
header to SPDX standard changes the license from GPLv2+ to GPLv2, and
this change corrects it.
Fixes: dae5f0afcf ("gpio: Use SPDX header for core library")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove linux/gpio/driver.h which is included more than once
Signed-off-by: Brajeswar Ghosh <brajeswar.linux@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some SoCs need the gpio clock to be enabled before accessing
HW registers. This patch add the optional clock handling.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 3edfb7bd76 ("gpiolib: Show correct direction from the
beginning") fixed an existing issue but broke libgpiod tests by
changing the default direction of dummy lines to output.
We don't break user-space so make gpio-mockup behave as before.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As pointed out by Gregor, spitz keyboard matrix is broken, with or
without CONFIG_PINCTRL set, quoting :
"The gpio matrix keypard on the Zaurus C3x00 (see spitz.c) does not work
properly. Noticeable are that rshift+c does nothing where as lshift+c
creates C. Opposite it is for rshift+a vs lshift+a, here only rshift
works. This affects a few other combinations using the rshift or lshift
buttons."
As a matter of fact, as for platform_data based builds CONFIG_PINCTRL=n
is required for now (as opposed for devicetree builds where it should be
set), this means gpio driver should change the direction, which is what
was attempted by commit c4e5ffb6f2 ("gpio: pxa: fix legacy non pinctrl
aware builds").
Unfortunately, the input case was inverted, and the direction change was
never done. This wasn't seen up until now because the initial platform
setup (MFP) was setting this direction. Yet in Gregory's case, the
matrix-keypad driver changes back and forth the direction dynamically,
and this is why he's the first to report it.
Fixes: c4e5ffb6f2 ("gpio: pxa: fix legacy non pinctrl aware builds")
Tested-by: Greg <greguu@null.net>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
During noirq suspend/resume phase, GPIO irq could arrive
and its registers like IMR will be changed by irq handle
process, to make the GPIO registers exactly when it is
powered ON after resume, move the GPIO noirq suspend/resume
callback to syscore suspend/resume phase, local irq is
disabled at this phase so GPIO registers are atomic.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 48207d7595 ("gpio: drop devm_gpiochip_remove()") dropped the
last user of drop devm_gpio_chip_match(), causing a defined but not used
compilation warning. Fix it by removing the function.
Fixes: 48207d7595 ("gpio: drop devm_gpiochip_remove()")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The change corrects the error path in gpiochip_add_data_with_key()
by avoiding to call ida_simple_remove(), if ida_simple_get() returns
an error.
Note that ida_simple_remove()/ida_free() throws a BUG(), if id argument
is negative, it allows to easily check the correctness of the fix by
fuzzing the return value from ida_simple_get().
Fixes: ff2b135922 ("gpio: make the gpiochip a real device")
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiod_request_commit() copies the pointer to the label passed as
an argument only to be used later. But there's a chance the caller
could immediately free the passed string(e.g., local variable).
This could trigger a use after free when we use gpio label(e.g.,
gpiochip_unlock_as_irq(), gpiochip_is_requested()).
To be on the safe side: duplicate the string with kstrdup_const()
so that if an unaware user passes an address to a stack-allocated
buffer, we won't get the arbitrary label.
Also fix gpiod_set_consumer_name().
Signed-off-by: Muchun Song <smuchun@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Trivial fix to clean up an indentation issue, remove space
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Keeping the irq_chip definition static will make it shared with multiple
giochips in the system. This practice is considered to be bad and now we
will get the below warning from gpiolib core:
"detected irqchip that is shared with multiple gpiochips: please fix the
driver."
Hence, move the irq_chip definition from static to `struct pl061` for
using a unique irq_chip for each gpiochip.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is hardly any reason to call devm_gpiochip_remove() because the
driver core handles calling gpiochip_remove() automatically.
To make it harder to introduce new (and probably unneeded) callers, drop
the function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch masks the read inputs with the word mask in order to ensure
only requested input states are returned in the bits array.
Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch masks the read inputs with the word mask in order to ensure
only requested input states are returned in the bits array.
Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch masks the read inputs with the word mask in order to ensure
only requested input states are returned in the bits array.
Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch masks the read inputs with the word mask in order to ensure
only requested input states are returned in the bits array.
Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch masks the read inputs with the word mask in order to ensure
only requested input states are returned in the bits array.
Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch masks the read inputs with the word mask in order to ensure
only requested input states are returned in the bits array.
Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With a new subsystem co-maintainer on board it is good to draw
up the ongoing changes and future plans for the subsystem, i.e.
what is in my head and being worked on long term.
What better way is there than simply adding a TODO right in the
code and send it out to the mailing list.
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAlvPV7IUHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vyaUg//WnCaRIu2oKOp8c/bplZJDW5eT10d
oYAN9qeyptU9RYrg4KBNbZL9UKGFTk3AoN5AUjrk8njxc/dY2ra/79esOvZyyYQy
qLXBvrXKg3yZnlNlnyBneGSnUVwv/kl2hZS+kmYby2YOa8AH/mhU0FIFvsnfRK2I
XvwABFm2ZYvXCqh3e5HXaHhOsR88NQ9In0AXVC7zHGqv1r/bMVn2YzPZHL/zzMrF
mS79tdBTH+shSvchH9zvfgIs+UEKvvjEJsG2liwMkcQaV41i5dZjSKTdJ3EaD/Y2
BreLxXRnRYGUkBqfcon16Yx+P6VCefDRLa+RhwYO3dxFF2N4ZpblbkIdBATwKLjL
npiGc6R8yFjTmZU0/7olMyMCm7igIBmDvWPcsKEE8R4PezwoQv6YKHBMwEaflIbl
Rv4IUqjJzmQPaA0KkRoAVgAKHxldaNqno/6G1FR2gwz+fr68p5WSYFlQ3axhvTjc
bBMJpB/fbp9WmpGJieTt6iMOI6V1pnCVjibM5ZON59WCFfytHGGpbYW05gtZEod4
d/3yRuU53JRSj3jQAQuF1B6qYhyxvv5YEtAQqIFeHaPZ67nL6agw09hE+TlXjWbE
rTQRShflQ+ydnzIfKicFgy6/53D5hq7iH2l7HwJVXbXRQ104T5DB/XHUUTr+UWQn
/Nkhov32/n6GjxQ=
=58I4
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Fix ASPM link_state teardown on removal (Lukas Wunner)
- Fix misleading _OSC ASPM message (Sinan Kaya)
- Make _OSC optional for PCI (Sinan Kaya)
- Don't initialize ASPM link state when ACPI_FADT_NO_ASPM is set
(Patrick Talbert)
- Remove x86 and arm64 node-local allocation for host bridge structures
(Punit Agrawal)
- Pay attention to device-specific _PXM node values (Jonathan Cameron)
- Support new Immediate Readiness bit (Felipe Balbi)
- Differentiate between pciehp surprise and safe removal (Lukas Wunner)
- Remove unnecessary pciehp includes (Lukas Wunner)
- Drop pciehp hotplug_slot_ops wrappers (Lukas Wunner)
- Tolerate PCIe Slot Presence Detect being hardwired to zero to
workaround broken hardware, e.g., the Wilocity switch/wireless device
(Lukas Wunner)
- Unify pciehp controller & slot structs (Lukas Wunner)
- Constify hotplug_slot_ops (Lukas Wunner)
- Drop hotplug_slot_info (Lukas Wunner)
- Embed hotplug_slot struct into users instead of allocating it
separately (Lukas Wunner)
- Initialize PCIe port service drivers directly instead of relying on
initcall ordering (Keith Busch)
- Restore PCI config state after a slot reset (Keith Busch)
- Save/restore DPC config state along with other PCI config state
(Keith Busch)
- Reference count devices during AER handling to avoid race issue with
concurrent hot removal (Keith Busch)
- If an Upstream Port reports ERR_FATAL, don't try to read the Port's
config space because it is probably unreachable (Keith Busch)
- During error handling, use slot-specific reset instead of secondary
bus reset to avoid link up/down issues on hotplug ports (Keith Busch)
- Restore previous AER/DPC handling that does not remove and
re-enumerate devices on ERR_FATAL (Keith Busch)
- Notify all drivers that may be affected by error recovery resets
(Keith Busch)
- Always generate error recovery uevents, even if a driver doesn't have
error callbacks (Keith Busch)
- Make PCIe link active reporting detection generic (Keith Busch)
- Support D3cold in PCIe hierarchies during system sleep and runtime,
including hotplug and Thunderbolt ports (Mika Westerberg)
- Handle hpmemsize/hpiosize kernel parameters uniformly, whether slots
are empty or occupied (Jon Derrick)
- Remove duplicated include from pci/pcie/err.c and unused variable
from cpqphp (YueHaibing)
- Remove driver pci_cleanup_aer_uncorrect_error_status() calls (Oza
Pawandeep)
- Uninline PCI bus accessors for better ftracing (Keith Busch)
- Remove unused AER Root Port .error_resume method (Keith Busch)
- Use kfifo in AER instead of a local version (Keith Busch)
- Use threaded IRQ in AER bottom half (Keith Busch)
- Use managed resources in AER core (Keith Busch)
- Reuse pcie_port_find_device() for AER injection (Keith Busch)
- Abstract AER interrupt handling to disconnect error injection (Keith
Busch)
- Refactor AER injection callbacks to simplify future improvments
(Keith Busch)
- Remove unused Netronome NFP32xx Device IDs (Jakub Kicinski)
- Use bitmap_zalloc() for dma_alias_mask (Andy Shevchenko)
- Add switch fall-through annotations (Gustavo A. R. Silva)
- Remove unused Switchtec quirk variable (Joshua Abraham)
- Fix pci.c kernel-doc warning (Randy Dunlap)
- Remove trivial PCI wrappers for DMA APIs (Christoph Hellwig)
- Add Intel GPU device IDs to spurious interrupt quirk (Bin Meng)
- Run Switchtec DMA aliasing quirk only on NTB endpoints to avoid
useless dmesg errors (Logan Gunthorpe)
- Update Switchtec NTB documentation (Wesley Yung)
- Remove redundant "default n" from Kconfig (Bartlomiej Zolnierkiewicz)
- Avoid panic when drivers enable MSI/MSI-X twice (Tonghao Zhang)
- Add PCI support for peer-to-peer DMA (Logan Gunthorpe)
- Add sysfs group for PCI peer-to-peer memory statistics (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA scatterlist mapping interface (Logan
Gunthorpe)
- Add PCI configfs/sysfs helpers for use by peer-to-peer users (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA driver writer's documentation (Logan
Gunthorpe)
- Add block layer flag to indicate driver support for PCI peer-to-peer
DMA (Logan Gunthorpe)
- Map Infiniband scatterlists for peer-to-peer DMA if they contain P2P
memory (Logan Gunthorpe)
- Register nvme-pci CMB buffer as PCI peer-to-peer memory (Logan
Gunthorpe)
- Add nvme-pci support for PCI peer-to-peer memory in requests (Logan
Gunthorpe)
- Use PCI peer-to-peer memory in nvme (Stephen Bates, Steve Wise,
Christoph Hellwig, Logan Gunthorpe)
- Cache VF config space size to optimize enumeration of many VFs
(KarimAllah Ahmed)
- Remove unnecessary <linux/pci-ats.h> include (Bjorn Helgaas)
- Fix VMD AERSID quirk Device ID matching (Jon Derrick)
- Fix Cadence PHY handling during probe (Alan Douglas)
- Signal Cadence Endpoint interrupts via AXI region 0 instead of last
region (Alan Douglas)
- Write Cadence Endpoint MSI interrupts with 32 bits of data (Alan
Douglas)
- Remove redundant controller tests for "device_type == pci" (Rob
Herring)
- Document R-Car E3 (R8A77990) bindings (Tho Vu)
- Add device tree support for R-Car r8a7744 (Biju Das)
- Drop unused mvebu PCIe capability code (Thomas Petazzoni)
- Add shared PCI bridge emulation code (Thomas Petazzoni)
- Convert mvebu to use shared PCI bridge emulation (Thomas Petazzoni)
- Add aardvark Root Port emulation (Thomas Petazzoni)
- Support 100MHz/200MHz refclocks for i.MX6 (Lucas Stach)
- Add initial power management for i.MX7 (Leonard Crestez)
- Add PME_Turn_Off support for i.MX7 (Leonard Crestez)
- Fix qcom runtime power management error handling (Bjorn Andersson)
- Update TI dra7xx unaligned access errata workaround for host mode as
well as endpoint mode (Vignesh R)
- Fix kirin section mismatch warning (Nathan Chancellor)
- Remove iproc PAXC slot check to allow VF support (Jitendra Bhivare)
- Quirk Keystone K2G to limit MRRS to 256 (Kishon Vijay Abraham I)
- Update Keystone to use MRRS quirk for host bridge instead of open
coding (Kishon Vijay Abraham I)
- Refactor Keystone link establishment (Kishon Vijay Abraham I)
- Simplify and speed up Keystone link training (Kishon Vijay Abraham I)
- Remove unused Keystone host_init argument (Kishon Vijay Abraham I)
- Merge Keystone driver files into one (Kishon Vijay Abraham I)
- Remove redundant Keystone platform_set_drvdata() (Kishon Vijay
Abraham I)
- Rename Keystone functions for uniformity (Kishon Vijay Abraham I)
- Add Keystone device control module DT binding (Kishon Vijay Abraham
I)
- Use SYSCON API to get Keystone control module device IDs (Kishon
Vijay Abraham I)
- Clean up Keystone PHY handling (Kishon Vijay Abraham I)
- Use runtime PM APIs to enable Keystone clock (Kishon Vijay Abraham I)
- Clean up Keystone config space access checks (Kishon Vijay Abraham I)
- Get Keystone outbound window count from DT (Kishon Vijay Abraham I)
- Clean up Keystone outbound window configuration (Kishon Vijay Abraham
I)
- Clean up Keystone DBI setup (Kishon Vijay Abraham I)
- Clean up Keystone ks_pcie_link_up() (Kishon Vijay Abraham I)
- Fix Keystone IRQ status checking (Kishon Vijay Abraham I)
- Add debug messages for all Keystone errors (Kishon Vijay Abraham I)
- Clean up Keystone includes and macros (Kishon Vijay Abraham I)
- Fix Mediatek unchecked return value from devm_pci_remap_iospace()
(Gustavo A. R. Silva)
- Fix Mediatek endpoint/port matching logic (Honghui Zhang)
- Change Mediatek Root Port Class Code to PCI_CLASS_BRIDGE_PCI (Honghui
Zhang)
- Remove redundant Mediatek PM domain check (Honghui Zhang)
- Convert Mediatek to pci_host_probe() (Honghui Zhang)
- Fix Mediatek MSI enablement (Honghui Zhang)
- Add Mediatek system PM support for MT2712 and MT7622 (Honghui Zhang)
- Add Mediatek loadable module support (Honghui Zhang)
- Detach VMD resources after stopping root bus to prevent orphan
resources (Jon Derrick)
- Convert pcitest build process to that used by other tools (iio, perf,
etc) (Gustavo Pimentel)
* tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI/AER: Refactor error injection fallbacks
PCI/AER: Abstract AER interrupt handling
PCI/AER: Reuse existing pcie_port_find_device() interface
PCI/AER: Use managed resource allocations
PCI: pcie: Remove redundant 'default n' from Kconfig
PCI: aardvark: Implement emulated root PCI bridge config space
PCI: mvebu: Convert to PCI emulated bridge config space
PCI: mvebu: Drop unused PCI express capability code
PCI: Introduce PCI bridge emulated config space common logic
PCI: vmd: Detach resources after stopping root bus
nvmet: Optionally use PCI P2P memory
nvmet: Introduce helper functions to allocate and free request SGLs
nvme-pci: Add support for P2P memory in requests
nvme-pci: Use PCI p2pmem subsystem to manage the CMB
IB/core: Ensure we map P2P memory correctly in rdma_rw_ctx_[init|destroy]()
block: Add PCI P2P flag for request queue
PCI/P2PDMA: Add P2P DMA driver writer's documentation
docs-rst: Add a new directory for PCI documentation
PCI/P2PDMA: Introduce configfs/sysfs enable attribute helpers
PCI/P2PDMA: Add PCI p2pmem DMA mappings to adjust the bus offset
...
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO
lines as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can
use only the fastpatch callbacks to enable/disable irqs
like any normal irqchip, especially the gpiod_lock_as_irq()
has been improved to be callable in fastpath context.
A bunch of rework had to be done to achieve this but it is
a big win since I never liked to restrict this to slowpath.
The only call requireing slowpath was try_module_get() and
this is kept at the .request_resources() slowpath callback.
In the GPIO CEC driver this is a big win sine a single
line is used for both outgoing and incoming traffic, and
this needs to use IRQs for incoming traffic while actively
driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a
"cookie" (struct gpio_array) and a bitmap for setting or
getting multiple GPIO lines at once. This improvement
orginated in a specific need to speed up an OMAP1 driver and
has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot
of checks and code when we want things to go really fast.
The previous code would minimize the number of calls
down to the driver callbacks assuming the CPU speed was
orders of magnitude faster than the I/O latency, but this
assumption was wrong on several platforms: what we needed
to do was to profile and improve the speed on the hot
path of the array functions and this change is now
completed.
- Clean out the painful and hard to grasp BNF experiments
from the device tree bindings. Future approaches are looking
into using JSON schema for this purpose. (Rob Herring
is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and
other contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin
control driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver.
-----BEGIN PGP SIGNATURE-----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=YosT
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.20 series:
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO lines
as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can use only
the fastpatch callbacks to enable/disable irqs like any normal
irqchip, especially the gpiod_lock_as_irq() has been improved to be
callable in fastpath context.
A bunch of rework had to be done to achieve this but it is a big
win since I never liked to restrict this to slowpath. The only call
requireing slowpath was try_module_get() and this is kept at the
.request_resources() slowpath callback. In the GPIO CEC driver this
is a big win sine a single line is used for both outgoing and
incoming traffic, and this needs to use IRQs for incoming traffic
while actively driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a "cookie"
(struct gpio_array) and a bitmap for setting or getting multiple
GPIO lines at once.
This improvement orginated in a specific need to speed up an OMAP1
driver and has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot of checks
and code when we want things to go really fast.
The previous code would minimize the number of calls down to the
driver callbacks assuming the CPU speed was orders of magnitude
faster than the I/O latency, but this assumption was wrong on
several platforms: what we needed to do was to profile and improve
the speed on the hot path of the array functions and this change is
now completed.
- Clean out the painful and hard to grasp BNF experiments from the
device tree bindings. Future approaches are looking into using JSON
schema for this purpose. (Rob Herring is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and other
contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin control
driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver"
* tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (116 commits)
gpio: Clarify kerneldoc on gpiochip_set_chained_irqchip()
gpio: Remove unused 'irqchip' argument to gpiochip_set_cascaded_irqchip()
gpio: Drop parent irq assignment during cascade setup
mmc: pwrseq_simple: Fix incorrect handling of GPIO bitmap
gpio: fix SNPS_CREG kconfig dependency warning
gpiolib: Initialize gdev field before is used
gpio: fix kernel-doc after devres.c file rename
gpio: fix doc string for devm_gpiochip_add_data() to not talk about irq_chip
gpio: syscon: Fix possible NULL ptr usage
gpiolib: Show correct direction from the beginning
pinctrl: msm: Use init_valid_mask exported function
gpiolib: Add init_valid_mask exported function
GPIO: add single-register GPIO via CREG driver
dt-bindings: Document the Synopsys GPIO via CREG bindings
gpio: mockup: use device properties instead of platform_data
gpio: Slightly more helpful debugfs
gpio: omap: Remove set but not used variable 'dev'
gpio: omap: drop omap_gpio_list
Accept partial 'gpio-line-names' property.
gpio: omap: get rid of the conditional PM runtime calls
...
There were no significant changes to the core this time!
New drivers:
- Broadcom Northstar pin control driver.
- Mediatek MT8183 subdriver.
- Mediatek MT7623 subdriver.
- Mediatek MT6765 subdriver.
- Meson g12a subdriver.
- Nuvoton NPCM7xx pin control and GPIO driver.
- Qualcomm QCS404 pin control and GPIO subdriver.
- Qualcomm SDM660 pin control and GPIO subdriver.
- Renesas R8A7744 PFC subdriver.
- Renesas R8A774C0 PFC subdriver.
- Renesas RZ/N1 pinctrl driver
Major improvements:
- Pulled the GPIO support for Ingenic over from the GPIO
subsystem and consolidated it all in the Ingenic pin control
driver.
- Major cleanups and consolidation work in all Intel drivers.
- Major cleanups and consolidation work in all Mediatek drivers.
- Lots of incremental improvements to the Renesas PFC pin
controller family.
- All drivers doing GPIO now include <linux/gpio/driver.h> and
nothing else.
-----BEGIN PGP SIGNATURE-----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=rBtH
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.20 series:
There were no significant changes to the core this time! Bur the new
Qualcomm, Mediatek and Broadcom drivers are quite interesting as they
will be used in a few million embedded devices the coming years as it
seems.
New drivers:
- Broadcom Northstar pin control driver.
- Mediatek MT8183 subdriver.
- Mediatek MT7623 subdriver.
- Mediatek MT6765 subdriver.
- Meson g12a subdriver.
- Nuvoton NPCM7xx pin control and GPIO driver.
- Qualcomm QCS404 pin control and GPIO subdriver.
- Qualcomm SDM660 pin control and GPIO subdriver.
- Renesas R8A7744 PFC subdriver.
- Renesas R8A774C0 PFC subdriver.
- Renesas RZ/N1 pinctrl driver
Major improvements:
- Pulled the GPIO support for Ingenic over from the GPIO subsystem
and consolidated it all in the Ingenic pin control driver.
- Major cleanups and consolidation work in all Intel drivers.
- Major cleanups and consolidation work in all Mediatek drivers.
- Lots of incremental improvements to the Renesas PFC pin controller
family.
- All drivers doing GPIO now include <linux/gpio/driver.h> and
nothing else"
* tag 'pinctrl-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (153 commits)
pinctrl: sunxi: Fix a memory leak in 'sunxi_pinctrl_build_state()'
gpio: uniphier: include <linux/bits.h> instead of <linux/bitops.h>
pinctrl: uniphier: include <linux/bits.h> instead of <linux/bitops.h>
dt-bindings: pinctrl: bcm4708-pinmux: improve example binding
pinctrl: geminilake: Sort register offsets by value
pinctrl: geminilake: Get rid of unneeded ->probe() stub
pinctrl: geminilake: Update pin list for B0 stepping
pinctrl: renesas: Fix platform_no_drv_owner.cocci warnings
pinctrl: mediatek: Make eint_m u16
pinctrl: bcm: ns: Use uintptr_t for casting data
pinctrl: madera: Fix uninitialized variable bug in madera_mux_set_mux
pinctrl: gemini: Fix up TVC clock group
pinctrl: gemini: Drop noisy debug prints
pinctrl: gemini: Mask and set properly
pinctrl: mediatek: select GPIOLIB
pinctrl: rza1: don't manually release devm managed resources
MAINTAINERS: update entry for Mediatek pin controller
pinctrl: bcm: add Northstar driver
dt-bindings: pinctrl: document Broadcom Northstar pin mux controller
pinctrl: qcom: fix 'const' pointer handling
...
The reason of including <linux/bitops.h> here is just for BIT() and
GENMASK macros.
Since commit 8bd9cb51da ("locking/atomics, asm-generic: Move some
macros from <linux/bitops.h> to a new <linux/bits.h> file"),
<linux/bits.h> is enough for such compile-time macros.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This doesn't support nested anymore, so drivers shouldn't call it with
the handler set to NULL.
Cc: Evan Green <evgreen@chromium.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This argument hasn't ever been used since it was introduced in commit
1425052097 ("gpio: add IRQ chip helpers in gpiolib"). Let's drop it to
reduce reading confusion.
Cc: Evan Green <evgreen@chromium.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We want to set the irq parent for interrupts that we're setting up to be
cascaded from another interrupt controller, but we may or may not have
already mapped the gpiochip irqs into the kernel's virtual irq number
space at this point. If we have mapped irqs before calling here, then
we've gone through gpiochip_irq_map() and called irq_set_parent()
already. If we haven't mapped irqs, then the gpiochip is dynamically
mapping irqs and we can rely on gpiochip_irq_map() or the gpio driver's
irqdomain ops to setup the irq parent properly.
Either way, setting the parent here when cascading the gpiochip doesn't
make much sense because it should be done at irq mapping time. In the
dynamic mapping case, this code is mapping virq 0 to some parent virq in
a loop. While that's benign, let's drop this code to simplify.
Cc: Evan Green <evgreen@chromium.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix kconfig warning for GPIO_SNPS_CREG:
WARNING: unmet direct dependencies detected for OF_GPIO
Depends on [n]: GPIOLIB [=y] && OF [=n] && HAS_IOMEM [=y]
Selected by [y]:
- GPIO_SNPS_CREG [=y] && GPIOLIB [=y] && HAS_IOMEM [=y] && (ARC || COMPILE_TEST [=y])
Drivers in drivers/gpio/Kconfig depend on OF_GPIO, not select it.
This prevents attempting to build when OF is not enabled.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This allows nonexclusive (simultaneous) access to a single
GPIO line for the fixed regulator enable line. This happens
when several regulators use the same GPIO for enabling and
disabling a regulator, and all need a handle on their GPIO
descriptor.
This solution with a special flag is not entirely elegant
and should ideally be replaced by something more careful as
this makes it possible for several consumers to
enable/disable the same GPIO line to the left and right
without any consistency. The current use inside the regulator
core should however be fine as it takes special care to
handle this.
For the state of the GPIO backend, this is still the
lesser evil compared to going back to global GPIO
numbers.
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Fixes: efdfeb079c ("regulator: fixed: Convert to use GPIO descriptor only")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
gpio_hog depends on gdev field being initialized. This patch fixes an
OOPs during initialization of TI's AM335x-ICEv2.
Fixes: 3edfb7bd76 ("gpiolib: Show correct direction from the beginning")
Tested-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiochip_set_cascaded_irqchip() is passed 'parent_irq' as an argument
and then the address of that argument is assigned to the gpio chips
gpio_irq_chip 'parents' pointer shortly thereafter. This can't ever
work, because we've just assigned some stack address to a pointer that
we plan to dereference later in gpiochip_irq_map(). I ran into this
issue with the KASAN report below when gpiochip_irq_map() tried to setup
the parent irq with a total junk pointer for the 'parents' array.
BUG: KASAN: stack-out-of-bounds in gpiochip_irq_map+0x228/0x248
Read of size 4 at addr ffffffc0dde472e0 by task swapper/0/1
CPU: 7 PID: 1 Comm: swapper/0 Not tainted 4.14.72 #34
Call trace:
[<ffffff9008093638>] dump_backtrace+0x0/0x718
[<ffffff9008093da4>] show_stack+0x20/0x2c
[<ffffff90096b9224>] __dump_stack+0x20/0x28
[<ffffff90096b91c8>] dump_stack+0x80/0xbc
[<ffffff900845a350>] print_address_description+0x70/0x238
[<ffffff900845a8e4>] kasan_report+0x1cc/0x260
[<ffffff900845aa14>] __asan_report_load4_noabort+0x2c/0x38
[<ffffff900897e098>] gpiochip_irq_map+0x228/0x248
[<ffffff900820cc08>] irq_domain_associate+0x114/0x2ec
[<ffffff900820d13c>] irq_create_mapping+0x120/0x234
[<ffffff900820da78>] irq_create_fwspec_mapping+0x4c8/0x88c
[<ffffff900820e2d8>] irq_create_of_mapping+0x180/0x210
[<ffffff900917114c>] of_irq_get+0x138/0x198
[<ffffff9008dc70ac>] spi_drv_probe+0x94/0x178
[<ffffff9008ca5168>] driver_probe_device+0x51c/0x824
[<ffffff9008ca6538>] __device_attach_driver+0x148/0x20c
[<ffffff9008ca14cc>] bus_for_each_drv+0x120/0x188
[<ffffff9008ca570c>] __device_attach+0x19c/0x2dc
[<ffffff9008ca586c>] device_initial_probe+0x20/0x2c
[<ffffff9008ca18bc>] bus_probe_device+0x80/0x154
[<ffffff9008c9b9b4>] device_add+0x9b8/0xbdc
[<ffffff9008dc7640>] spi_add_device+0x1b8/0x380
[<ffffff9008dcbaf0>] spi_register_controller+0x111c/0x1378
[<ffffff9008dd6b10>] spi_geni_probe+0x4dc/0x6f8
[<ffffff9008cab058>] platform_drv_probe+0xdc/0x130
[<ffffff9008ca5168>] driver_probe_device+0x51c/0x824
[<ffffff9008ca59cc>] __driver_attach+0x100/0x194
[<ffffff9008ca0ea8>] bus_for_each_dev+0x104/0x16c
[<ffffff9008ca58c0>] driver_attach+0x48/0x54
[<ffffff9008ca1edc>] bus_add_driver+0x274/0x498
[<ffffff9008ca8448>] driver_register+0x1ac/0x230
[<ffffff9008caaf6c>] __platform_driver_register+0xcc/0xdc
[<ffffff9009c4b33c>] spi_geni_driver_init+0x1c/0x24
[<ffffff9008084cb8>] do_one_initcall+0x240/0x3dc
[<ffffff9009c017d0>] kernel_init_freeable+0x378/0x468
[<ffffff90096e8240>] kernel_init+0x14/0x110
[<ffffff9008086fcc>] ret_from_fork+0x10/0x18
The buggy address belongs to the page:
page:ffffffbf037791c0 count:0 mapcount:0 mapping: (null) index:0x0
flags: 0x4000000000000000()
raw: 4000000000000000 0000000000000000 0000000000000000 00000000ffffffff
raw: ffffffbf037791e0 ffffffbf037791e0 0000000000000000 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffffffc0dde47180: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffffffc0dde47200: f1 f1 f1 f1 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f2 f2
>ffffffc0dde47280: f2 f2 00 00 00 00 00 00 00 00 00 00 f3 f3 f3 f3
^
ffffffc0dde47300: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffffffc0dde47380: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Let's leave around one unsigned int in the gpio_irq_chip struct for the
single parent irq case and repoint the 'parents' array at it. This way
code is left mostly intact to setup parents and we waste an extra few
bytes per structure of which there should be only a handful in a system.
Cc: Evan Green <evgreen@chromium.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Fixes: e0d8972898 ("gpio: Implement tighter IRQ chip integration")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The function is about adding a gpio_chip so dev has to belong to this
one. Fix wording to be more grammatically correct (but attention, I'm
not a native speaker).
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The priv->data->set can be NULL while flags contains GPIO_SYSCON_FEAT_OUT
and chip->set is valid pointer. This happens in case the controller uses
the default GPIO setter. Always use chip->set to access the setter to avoid
possible NULL pointer dereferencing.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Current code assumes that the direction is input if direction_input
function is set.
This might not be the case on GPIOs with programmable direction.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a function that allows initializing the valid_mask from
gpiochip_add_data.
This prevents race conditions during gpiochip initialization.
If the function is not exported, then the old behaviour is respected,
this is, set all gpios as valid.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add single-register MMIO GPIO driver for complex cases where
only several fields in register belong to GPIO lines and each GPIO
line owns a field with different length and on/off value.
Such CREG GPIOs are used in Synopsys AXS10x and HSDK boards.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some users want to introduce device tree support to the mockup driver.
Let's make it easier by switching to using generic device properties.
The driver stays compatible with previous use cases and after this
conversion there'll be no need to change the way probing of mockup
GPIO chips works.
Tested with libgpiod test suite.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is possible to have _DSD entries where the data is compatible with
device properties format but are using different GUID for various reasons.
In addition to that there can be many such _DSD entries for a single device
such as for PCIe root port used to host a Thunderbolt hierarchy:
Scope (\_SB.PCI0.RP21)
{
Name (_DSD, Package () {
ToUUID ("6211e2c0-58a3-4af3-90e1-927a4e0c55a4"),
Package () {
Package () {"HotPlugSupportInD3", 1}
},
ToUUID ("efcc06cc-73ac-4bc3-bff0-76143807c389"),
Package () {
Package () {"ExternalFacingPort", 1},
Package () {"UID", 0 }
}
})
}
More information about these new _DSD entries can be found in:
https://docs.microsoft.com/en-us/windows-hardware/drivers/pci/dsd-for-pcie-root-ports
To make these available for drivers via unified device property APIs,
modify ACPI property core so that it supports multiple _DSD entries
organized in a linked list. We also store GUID of each _DSD entry in struct
acpi_device_properties in case there is need to differentiate between
entries. The supported GUIDs are then listed in prp_guids array.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
This at least makes debugfs print if the line is active
high or low. That is pretty helpful as what we display
as "lo" or "hi" is the raw physical level of the line.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpio/gpio-omap.c: In function 'gpio_omap_cpu_notifier':
drivers/gpio/gpio-omap.c:1327:17: warning:
variable 'dev' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
omap_gpio_list is unused so drop it.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEZH8oZUiU471FcZm+ONu9yGCSaT4FAluw4MIACgkQONu9yGCS
aT7+8xAAiYnc4khUsxeInm3z44WPfRX1+UF51frTNSY5C8Nn5nvRSnTUNLuKkkrz
8RbwCL6UYyJxF9I/oZdHPsPOD4IxXkQY55tBjz7ZbSBIFEwYM6RJMm8mAGlXY7wq
VyWA5MhlpGHM9DjrguB4DMRipnrSc06CVAnC+ZyKLjzblzU1Wdf2dYu+AW9pUVXP
j4r74lFED5djPY1xfqfzEwmYRCeEGYGx7zMqT3GrrF5uFPqj1H6O5klEsAhIZvdl
IWnJTU2coC8R/Sd17g4lHWPIeQNnMUGIUbu+PhIrZ/lDwFxlocg4BvarPXEdzgYi
gdZzKBfovpEsSu5RCQsKWG4IGQxY7I1p70IOP9eqEFHZy77qT1YcHVAWrK1Y/bJd
UA08gUOSzRnhKkNR3+PsaMflUOl9WkpyHECZu394cyRGMutSS50aWkavJPJ/o1Qi
D/oGqZLLcKFyuNcchG+Met1TzY3LvYEDgSburqwqeUZWtAsGs8kmiiq7qvmXx4zV
IcgM8ERqJ8mbfhfsXQU7hwydIrPJ3JdIq19RnM5ajbv2Q4C/qJCyAKkQoacrlKR4
aiow/qvyNrP80rpXfPJB8/8PiWeDtAnnGhM+xySZNlw3t8GR6NYpUkIzf5TdkSb3
C8KuKg6FY9QAS62fv+5KK3LB/wbQanxaPNruQFGe5K1iDQ5Fvzw=
=dMl4
-----END PGP SIGNATURE-----
Merge tag 'v4.19-rc6' into devel
This is the 4.19-rc6 release
I needed to merge this in because of extensive conflicts in
the MSM and Intel pin control drivers. I know how to resolve
them, so let's do it like this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Documentation/devicetree/bindings/gpio/gpio.txt says: "The names are
assigned starting from line offset 0 from left to right from the
passed array. An incomplete array (where the number of passed named
are less than ngpios) will still be used up until the last provided
valid line index". This patch makes it actually work this way.
Signed-off-by: Christophe Blaess <christophe.blaess@logilin.fr>
Signed-off-by: Patrick Boettcher <p@yai.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
OMAP GPIO driver is checking !BANK_USED() used condition before calling PM
runtime API, because of PM runtime calls in
omap2_gpio_prepare/resume_for_idle(). It's not required any more since
"omap gpio add level idle, cpu_pm and drop runtime_irq_safe" series [1]
from Tony Lindgren was accepted and PM runtime management was enabled in
IRQ chip core by commit be45beb2df ("genirq: Add runtime power management
support for IRQ chips") .
As result safely drop !BANK_USED() checks from omap_gpio_request/free(),
omap_gpio_irq_bus_lock/unlock() and enable PM runtime management for OMAP
GPIO IRQ chip.
[1] https://www.spinics.net/lists/arm-kernel/msg677583.html
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpio/gpio-htc-egpio.c: In function 'egpio_set':
drivers/gpio/gpio-htc-egpio.c:192:20: warning:
variable 'bit' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Internal helper function gpiod_set_array_value_complex() was changed to
return an error value, but not all gpiolib callers were updated to
propagate the new error up.
Fixes: 3027743f83 ("gpio: Remove VLA from gpiolib")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit b17566a6b0 ("gpiolib: Implement fast processing path in
get/set array"), already fixed to some extent with commit 5d581d7e8cdc
("gpiolib: Fix missing updates of bitmap index"), introduced a new mode
of processing bitmaps where bits applicable for fast bitmap processing
path are supposed to be skipped while iterating bits which don't apply.
Unfortunately, find_next_zero_bit() function supposed to skip over
those fast bits is always called with a 'start' argument equal to an
index of last zero bit found and returns that index value again an
again, causing an infinite loop.
Fix it by incrementing the index uncoditionally before
find_next_zero_bit() is optionally called.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver controls a SIOX device that provides 20 I/O lines. The first
twelve are fixed inputs, the remaining eight are outputs.
Acked-by: Gavin Schenk <g.schenk@eckelmann.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A patch from Ricardo got me thinking about some gpio chip
semantics so let's drop in some comments to make things
more clear around that.
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIOs with no programmable direction are not required to implement
direction_output nor direction_input.
If we try to set an output direction on an output-only GPIO or input
direction on an input-only GPIO simply return 0.
This allows this single direction GPIO to be used by libgpiod.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All the other core files are named "gpiolib-<something>" so
let's rename the devres as well so we have some logical
namespacing here.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the SPDX headers and cut down on boilerplate to indicate the
license in the core gpiolib implementation.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If a gpio instance has any GPIO bits requested we do a pm_runtime_get()
on the device. Now with cpu_pm handling the deeper SoC idle state quirks,
let's just remove pm_runtime_irq_safe() call and add a warning in case we
ever happen to encounter it.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For a long time the gpio-omap custom PM calls have been annoying me so
let's replace them with cpu_pm instead. This will enable GPIO PM for
deeper idle states on omap4. And we can handle GPIO PM for omap2/3/4
in the same way.
Note that with this patch we are also slightly changing GPIO PM to be
less aggressive for omap3 and only will idle GPIO when PER context
may be lost.
For omap2, we don't need to save context and don't want to remove any
triggering so let's add a quirk flag for that.
Let's do this all in a single patch to avoid a situation where old
custom calls still are used with new code.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I noticed that unlike omap2 and 3 based SoCs, omap4 based SoCs keep
the GPIO clocks enabled for GPIO level interrupts with wakeup enabled.
This blocks deeper idle states as the whole domain will stay busy.
The GPIO functional clock seems to stay enabled if the wakeup register
is enabled and a level interrupt is triggered. In that case the only
way to have the GPIO module idle is to reset it. It is possible this
has gone unnoticed with OSWR (Open SWitch Retention) and off mode
during idle resetting GPIO context most GPIO instances in the earlier
Android trees for example.
Looks like the way to deal with this is to have omap4 based SoCs
only set wake for the duration of idle for level interrupts, and clear
level registers for the idle. With level interrupts we can do this as
the level interrupt from device will be still there on resume.
I've taken the long path to fixing this to avoid yet more hard to
read code. I've set up a quirks flag, and a struct for function
pointers so we can use these to clean up other quirk handling easier
in the later patches. The current level quirk handling is moved to
the new functions.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
New code introduced by commit bf9346f5d4 ("gpiolib: Identify arrays
matching GPIO hardware") forcibly tries to find an array member which
has its array index number equal to its hardware pin number and set
up an array info for possible fast bitmap processing of all arrray
pins belonging to that chip which also satisfy that numbering rule.
Depending on array content, it may happen that consecutive array
members which belong to the same chip but don't have array indexes
equal to their pin hardware numbers will be split into groups, some of
them processed together via the fast bitmap path, and rest of them
separetely. However, applications may expect all those pins being
processed together with a single call to .set_multiple() chip callback,
like that was done before the change.
Limit applicability of fast bitmap processing path to cases where all
pins of consecutive array members starting from 0 which belong to the
same chip have their hardware numbers equal to their corresponding
array indexes. That should still speed up processing of applications
using whole GPIO banks as I/O ports, while not breaking simultaneous
manipulation of consecutive pins of the same chip which don't follow
the equal numbering rule.
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In new code introduced by commit b17566a6b0 ("gpiolib: Implement fast
processing path in get/set array"), bitmap index is not updated with
next found zero bit position as it should while skipping over pins
already processed via fast bitmap path, possibly resulting in an
infinite loop. Fix it.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Give the HTC EGPIO chips unique names, htc-egpio-0,
htc-egpio-1 etc, so that it gets possible to associate
machine descriptor tables with individual chips.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These defines, structs and inline functions are used only internally by
the driver, they do not belong in platform_data. Move them.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Acked-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Previously we created a controller structure per bank of GPIO pins. This
has since been changed to one per controller, but the allocation size
was not changed. Fix this here.
This also leaves the variable 'nbank' unused, instead of removing it,
move it down and use it to clean up a loop. For loops with multiple
initializers and/or iteration expressions, especially ones that don't
use those loop counters are quite hard to follow, fix this.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Acked-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use dev_name to get a unique label and use -1 for a base to get our
selection automatically. We pull in all GPIOs per chip now so this
does not have the effect of out of order labels like before.
We do these both together so we can drop all the static data in one
patch. This also lets us normalize the return paths as we don't need
any cleanup after this change.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Acked-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current code only frees N-1 gpios if an error occurs during
gpiod_set_transitory, gpiod_direction_output or gpiod_direction_input.
Leading to gpios that cannot be used by userspace nor other drivers.
Cc: Timur Tabi <timur@codeaurora.org>
Cc: stable@vger.kernel.org
Fixes: ab3dbcf78f ("gpioib: do not free unrequested descriptors)
Reported-by: Jan Lorenzen <jl@newtec.dk>
Reported-by: Jim Paris <jim@jtan.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A bunch of core gpiolib files still include the <linux/gpio.h>
legacy API header for no good reason. After this only the
gpiolib-legacy.c file includes it, which is fine.
The sysfs ABI code has a pointless wrapper function around
gpio_to_desc() we can just loose.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Just use the SPDX license tag for these drivers.
Cc: patches@opensource.cirrus.com
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Cc: Mark Brown <broonie@kernel.org>
Acked-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These are GPIO drivers so just include <linux/gpio/driver.h>.
Cc: patches@opensource.cirrus.com
Cc: Charles Keepax <ckeepax@opensource.cirrus.com>
Cc: Mark Brown <broonie@kernel.org>
Acked-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a GPIO driver so include only <linux/gpio/driver.h>.
Cc: Kamlakant Patel <kamlakant.patel@cavium.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a GPIO driver so include only <linux/gpio/driver.h>.
Cc: Daniel Drake <drake@endlessm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a GPIO driver so include only <linux/gpio/driver.h>.
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a GPIO driver so include only <linux/gpio/driver.h>.
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This API is not used anywhere in the kernel and has remained
unused for years after being introduced.
Over time, we have developed a subsystem to deal with pin
control and this now managed pull up/down.
Delete the old and unused API. If this platform needs it,
we should implement a proper pin controller for it instead.
Cc: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a GPIO driver so include only <linux/gpio/driver.h>.
Cc: Yoichi Yuasa <yuasa@linux-mips.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some drivers use a single irqchip for multiple gpiochips. As a result the
irqchip hooks are overridden for the first gpiochip that was added, but
for the other gpiochip instances this should not happen again, otherwise
we would go into an infinite recursion.
Check for this, but also log a message that the driver should be fixed
since this is bad practice.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
EINVAL is very generic, use ENOTSUPP in case the gpiochip does not
provide this function. While removing the assignment from the 'status'
variable, use better indentation in the declaration block.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Certain GPIO descriptor arrays returned by gpio_get_array() may contain
information on direct mapping of array members to pins of a single GPIO
chip in hardware order. In such cases, bitmaps of values can be passed
directly from/to the chip's .get/set_multiple() callbacks without
wasting time on iterations.
Add respective code to gpiod_get/set_array_bitmap_complex() functions.
Pins not applicable for fast path are processed as before, skipping
over the 'fast' ones.
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to make use of array info obtained from gpiod_get_array() and
speed up processing of arrays matching single GPIO chip layout, that
information must be passed to get/set array functions. Extend the
functions' API with that additional parameter and update all users.
Pass NULL if a user builds an array itself from single GPIOs.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Certain GPIO array lookup results may map directly to GPIO pins of a
single GPIO chip in hardware order. If that condition is recognized
and handled efficiently, significant performance gain of get/set array
functions may be possible.
While processing a request for an array of GPIO descriptors, identify
those which represent corresponding pins of a single GPIO chip. Skip
over pins which require open source or open drain special processing.
Moreover, identify pins which require inversion. Pass a pointer to
that information with the array to the caller so it can benefit from
enhanced performance as soon as get/set array functions can accept and
make efficient use of it.
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Most users of get/set array functions iterate consecutive bits of data,
usually a single integer, while processing array of results obtained
from, or building an array of values to be passed to those functions.
Save time wasted on those iterations by changing the functions' API to
accept bitmaps.
All current users are updated as well.
More benefits from the change are expected as soon as planned support
for accepting/passing those bitmaps directly from/to respective GPIO
chip callbacks if applicable is implemented.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This concerns gpio edge detection for GPIO IRQs used from
userspace for GPIO event listeners.
Trying to work out the right event if it's not sure that the
examined gpio actually moved is impossible.
Consider two gpios "gpioA" and "gpioB" that share an interrupt.
gpioA's irq should trigger on any edge, gpioB's on a falling edge.
If now the common irq fires and both gpio lines are high, there
are several possibilities that could have happend:
a) gpioA just had a low-to-high edge
b) gpioB just had a high-to-low-to-high spike
c) a combination of both a) and b)
While c) is unlikely (in most setups) a) and b) alone are bad
enough. Currently the code assumes case a) unconditionally and
doesn't report an event for gpioB. Note that even if there is no
irq sharing involved a spike for a gpio might not result in an
event if it's configured to trigger for a single edge only.
The only way to improve this is to drop support for interrupt
sharing. This way a spike results in an event for the right gpio
at least. Note that apart from dropping IRQF_SHARED this
effectively undoes commit df1e76f28f
("gpiolib: skip unwanted events, don't convert them to opposite edge").
This obviously breaks setups that rely on interrupt sharing,
but given that this cannot be reliable, this is probably an
acceptable trade-off.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[Assuming there are no users of interrupt sharing yet]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a GPIO driver so only include <linux/gpio/driver.h>.
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SPI chipselects are assumed to be active low in the current
binding, so when we want to use GPIO descriptors and handle
the active low/high semantics in gpiolib, we need a special
parsing quirk to deal with this.
We check for the property "spi-cs-high" and if that is
NOT present we assume the CS line is active low.
If the line is tagged as active low in the device tree and
has no "spi-cs-high" property all is fine, the device
tree and the SPI bindings are in agreement.
If the line is tagged as active high in the device tree with
the second cell flag and has no "spi-cs-high" property we
enforce active low semantics (as this is the exception we can
just tag on the flag).
If the line is tagged as active low with the second cell flag
AND tagged with "spi-cs-high" the SPI active high property
takes precedence and we print a warning.
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-spi@vger.kernel.org
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since this driver does not use the gpiolib irqchip helpers it will have to
allocate the irq resources and irq_en/disable itself.
Use the new gpiochip_req/relres_irq helpers to request/release all the
resources.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Ray Jui <rjui@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When using the gpiolib irqchip helpers install irq_enable/disable
hooks for the irqchip to ensure that gpiolib knows when the irq
is enabled or disabled, allowing drivers to disable the irq and then
use it as an output pin, and later switch the direction to input and
re-enable the irq.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO drivers call gpiochip_(un)lock_as_irq whenever they want to use a gpio
as an interrupt. This is done when the irq is requested and it marks the
gpio as in use by an interrupt.
This is problematic for cases where a gpio pin is used as an interrupt
pin, then, after the irq is disabled, is used as a regular gpio pin.
Currently it is not possible to do this other than by first freeing
the interrupt so gpiochip_unlock_as_irq is called, since an attempt to
switch the gpio direction for output will fail since gpiolib believes
that the gpio is in use for an interrupt and it does not know that it
the irq is actually disabled.
There are currently two drivers that would like to be able to do this:
the tda998x_drv.c driver where a regular gpio pin needs to be temporarily
reconfigured as an interrupt pin during CEC calibration, and the cec-gpio
driver where you want to configure the gpio pin as an interrupt while
waiting for traffic over the CEC bus, or as a regular pin when receiving or
transmitting a CEC message.
The solution is to add a new flag that is set when the irq is enabled,
and have gpiod_direction_output check for that flag.
We also add functions that drivers that do not use GPIOLIB_IRQCHIP
can call when they enable/disable the irq.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Centralize setting the irq_request/release_resources callbacks
in one function since we'll be adding more callbacks to that.
Also fix the removal of the callback overrides: this should
only be done if we actually installed our own callback there.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO drivers that do not use GPIOLIB_IRQCHIP can hook these into
the irq_request_resource and irq_release_resource callbacks of the
irq_chip so they correctly 'get' the module and lock the gpio line
for IRQ use.
This will simplify driver code.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The problem is that if port == ARRAY_SIZE() and "gc == &epg->gc[port]"
then that should be treated as invalid.
Fixes: fd935fc421 ("gpio: ep93xx: Do not pingpong irq numbers")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently the while loop checks for the end of the array using
the size of egp->gc rather that the number of elements in the array,
so fix this. Also, perform the array size check first as stylistically
it is always good to bounds check on an array first before referencing
the array (in this case, we're just computing the address of an
element in an array so this is a moot point).
Fixes: fd935fc421 ("gpio: ep93xx: Do not pingpong irq numbers")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpiolib cannot deduce the fact that every line is output
by itself, implement a .get_direction() callback so we can
inspect this.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's nice to use BIT() macros rather than open coding the same.
It's good practice as sometimes people use BIT(31) and forget
that the constant must be cast unsigned long.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the SPDX header to indicate the license for this driver.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a GPIO driver so include only <linux/gpio/driver.h>.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's nice to be able to read back the direction of the GPIO
line from the hardware so implement .get_direction() for
twl4030.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the SPDX header to indicate the license for this driver.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a GPIO driver so include only <linux/gpio/driver.h>.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The TS5500 GPIO driver apparently supports platform data
without making any use of it whatsoever. Delete this code,
last chance to speak up if you think it is needed.
Cc: kernel@savoirfairelinux.com
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Jerome Oufella <jerome.oufella@savoirfairelinux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a GPIO driver so include only <linux/gpio/driver.h>.
Cc: kernel@savoirfairelinux.com
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Jerome Oufella <jerome.oufella@savoirfairelinux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The MXS driver was calling back into the GPIO API from
its irqchip. This is not very elegant, as we are a driver,
let's just shortcut back into the gpio_chip .get() function
instead.
This is a tricky case since the .get() callback is not in
this file, instead assigned by bgpio_init(). Calling the
function direcly in the gpio_chip is however the lesser
evil.
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Janusz Uzycki <j.uzycki@elproma.com.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I'm tired of boilerplate, use the SPDX tag.
Acked-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These are drivers so include only <linux/gpio/driver.h>.
Acked-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiochip_add_data_with_key() adds the gpiochip to the gpio_devices list
before of_gpiochip_add() is called, but it's only the latter which sets
the ->of_xlate function pointer. gpiochip_find() can be called by
someone else between these two actions, and it can find the chip and
call of_gpiochip_match_node_and_xlate() which leads to the following
crash due to a NULL ->of_xlate().
Unhandled prefetch abort: page domain fault (0x01b) at 0x00000000
Modules linked in: leds_gpio(+) gpio_generic(+)
CPU: 0 PID: 830 Comm: insmod Not tainted 4.18.0+ #43
Hardware name: ARM-Versatile Express
PC is at (null)
LR is at of_gpiochip_match_node_and_xlate+0x2c/0x38
Process insmod (pid: 830, stack limit = 0x(ptrval))
(of_gpiochip_match_node_and_xlate) from (gpiochip_find+0x48/0x84)
(gpiochip_find) from (of_get_named_gpiod_flags+0xa8/0x238)
(of_get_named_gpiod_flags) from (gpiod_get_from_of_node+0x2c/0xc8)
(gpiod_get_from_of_node) from (devm_fwnode_get_index_gpiod_from_child+0xb8/0x144)
(devm_fwnode_get_index_gpiod_from_child) from (gpio_led_probe+0x208/0x3c4 [leds_gpio])
(gpio_led_probe [leds_gpio]) from (platform_drv_probe+0x48/0x9c)
(platform_drv_probe) from (really_probe+0x1d0/0x3d4)
(really_probe) from (driver_probe_device+0x78/0x1c0)
(driver_probe_device) from (__driver_attach+0x120/0x13c)
(__driver_attach) from (bus_for_each_dev+0x68/0xb4)
(bus_for_each_dev) from (bus_add_driver+0x1a8/0x268)
(bus_add_driver) from (driver_register+0x78/0x10c)
(driver_register) from (do_one_initcall+0x54/0x1fc)
(do_one_initcall) from (do_init_module+0x64/0x1f4)
(do_init_module) from (load_module+0x2198/0x26ac)
(load_module) from (sys_finit_module+0xe0/0x110)
(sys_finit_module) from (ret_fast_syscall+0x0/0x54)
One way to fix this would be to rework the hairy registration sequence
in gpiochip_add_data_with_key(), but since I'd probably introduce a
couple of new bugs if I attempted that, simply add a check for a
non-NULL of_xlate function pointer in
of_gpiochip_match_node_and_xlate(). This works since the driver looking
for the gpio will simply fail to find the gpio and defer its probe and
be reprobed when the driver which is registering the gpiochip has fully
completed its probe.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Sometimes we have empty banks within the GPIO block. This commit allows
proper handling of 0 width GPIO banks. We handle 0 width GPIO banks by
incrementing the bank and number of GPIOs, but not initializing them.
This will mean a call into the non-existent GPIOs will return an error.
Also remove "GPIO registered" dev print. This information is misleading
since the incremented banks and gpio_base do not reflect the actual GPIOs
that get initialized. We leave this information out since it is already
printed with dev_dbg.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The FTGPIO010 has a debounce timer or rather prescaler that
will affect interrupts fireing off the block. We can support
this to get proper debounce on e.g. keypresses.
Since the same prescaler is used across all GPIO lines of
the silicon block, we need to bail out if the prescaler is
already set and in use by another line.
If the prescaler is already set to what we need, fine, we
reuse it. This happens more often than not when the same
debounce time is set for several GPIO keys, so we support
that usecase easily with this code.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO silicon is clocked with a PCLK (peripheral clock)
on all systems, however not all platforms model it and include
it in e.g. the device tree, so add clock handling but make it
optional so we bail out safely if it is e.g. always on.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If dwapb_gpio_add_port() fails in dwapb_gpio_probe(),
gpio->clk is left undisabled.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the corner case where the gpio driver probe fails, for whatever
reason, the suspend and resume handlers will still be called as they
have to be registered as syscore operations. This applies as well when
no probe was called while the driver has been built in the kernel.
Nicolas tracked this in :
https://bugzilla.kernel.org/show_bug.cgi?id=200905
Therefore, add a failsafe in these function, and test if a proper probe
succeeded and the driver is functional.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reported-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl-ingenic driver is now handling the GPIO chips directly.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GpioInt ACPI event handlers may see there IRQ triggered immediately
after requesting the IRQ (esp. level triggered ones). This means that they
may run before any other (builtin) drivers have had a chance to register
their OpRegion handlers, leading to errors like this:
[ 1.133274] ACPI Error: No handler for Region [PMOP] ((____ptrval____)) [UserDefinedRegion] (20180531/evregion-132)
[ 1.133286] ACPI Error: Region UserDefinedRegion (ID=141) has no handler (20180531/exfldio-265)
[ 1.133297] ACPI Error: Method parse/execution failed \_SB.GPO2._L01, AE_NOT_EXIST (20180531/psparse-516)
We already defer the manual initial trigger of edge triggered interrupts
by running it from a late_initcall handler, this commit replaces this with
deferring the entire acpi_gpiochip_request_interrupts() call till then,
fixing the problem of some OpRegions not being registered yet.
Note that this removes the need to have a list of edge triggered handlers
which need to run, since the entire acpi_gpiochip_request_interrupts() call
is now delayed, acpi_gpiochip_request_interrupt() can call these directly
now.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The commit ca876c7483
("gpiolib-acpi: make sure we trigger edge events at least once on boot")
added a initial value check for pin which is about to be locked as IRQ.
Unfortunately, not all GPIO drivers can do that atomically. Thus,
switch to cansleep version of the call. Otherwise we have a warning:
...
WARNING: CPU: 2 PID: 1408 at drivers/gpio/gpiolib.c:2883 gpiod_get_value+0x46/0x50
...
RIP: 0010:gpiod_get_value+0x46/0x50
...
The change tested on Intel Broxton with Whiskey Cove PMIC GPIO controller.
Fixes: ca876c7483 ("gpiolib-acpi: make sure we trigger edge events at least once on boot")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This fixes:
[BUG] gpio: gpio-adp5588: A possible sleep-in-atomic-context bug
in adp5588_gpio_write()
[BUG] gpio: gpio-adp5588: A possible sleep-in-atomic-context bug
in adp5588_gpio_direction_input()
Reported-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO hole is present in RZ/G1C SoC. Valid GPIO pins on bank3 are in the
range GP3_0 to GP3_16 and GP3_27 to GP3_29. The GPIO pins between GP3_17
to GP3_26 are unused. Add support for handling unused GPIO's.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We can quite easily switch banks/ports A and B to use
GPIOLIB_IRQCHIP which is code that will be more careful
about handling interrupt descriptors and use a proper
irqdomain for translating the IRQs. This cuts down some
code in favor of using the implementation inside
gpiolib.
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This removes the callback into the gpiolib creating a
circular call to convert between GPIO numbers and IRQs
and pushes the whole business into the driver, just
using an array of IRQ bases for the three IRQ capable
ports.
This way we get rid of including <linux/gpio.h> that
no driver should include.
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This simplifies and standardizes the AB IRQ handler by using
the for_each_set_bit() library function.
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the IRQ-related functions, switch to using the hwirq
and port number found from the current struct gpio_chip *
As the lower 3 bits of the IRQ number is identical to the
lower 3 bits of the GPIO number we can cut some corners.
Call directly into the gpiochip to set up the direction
and read the input instead of using the consumer API.
This enabled us to cut the confusing irq_to_gpio() macro
that is a remnant of the old generic GPIO API as well.
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For setting debounce config we want to write an offset in
a per-gpiochip register, and we know which gpiochip we are
on. Instead of a roundtrip over the IRQ number, figure out
what port we are on for this GPIO chip, then index to the
right register and write the value.
This adds the ep93xx_gpio_port() that finds the port index
from a struct gpio_chip * that we can later exploit to
simplify more code.
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The chained irq handler should call chained_irq_enter()
and chained_irq_exit() before/after handling the chained
IRQ.
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is closer to what the variable (per bank) actually
means. We have the .gpio_to_irq() hook registered only
when this is true.
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of using a global variable, pass around the
struct gpio_chip * pointer and dereference to the state
container struct ep93xx_gpio as needed, like all other
drivers do.
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The subject says it all. Cut down on boilerplate.
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to clean up the driver I need to cut a few trees,
sorry, variable names, so I can see the forest, sorry driver
properly.
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As a preparation for multiplatform support, this ensures
that the ep93xx gpio driver can be built without any of
the platform specific header files. We pass the IRQ numbers
as a resource now, and use the virtual mmio base from the
already existing resource, rather than relying on the
hardwired virtual address from the header file.
Some numbers are now hardcoded that came from macros
in the past, but for all I can tell, the driver already
relied on the specific values.
Cc: arm@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of open coding logic for reading and writing GPIO lines,
use the generic GPIO library. Also switch to using the spinlock
from the generic GPIO to protect the registers.
Cc: linux-snps-arc@lists.infradead.org
Acked-by: Christian Ruppert <christian.ruppert@alitech.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Create a local struct device *dev helper variable to make the code
easier to read.
Most GPIO drivers use "np" (node pointer) rather than "dn" (device node)
to point to the device tree node. Let's follow this convention.
Cc: linux-snps-arc@lists.infradead.org
Acked-by: Christian Ruppert <christian.ruppert@alitech.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add Cirrus Logic Madera Codec (CS47L35, CS47L85 and CS47L90/91) driver
- Add ChromeOS EC CEC driver
- Add ROHM BD71837 PMIC driver
- New Device Support
- Add support for Dialog Semi DA9063L PMIC variant to DA9063
- Add support for Intel Ice Lake to Intel-PLSS-PCI
- Add support for X-Powers AXP806 to AXP20x
- New Functionality
- Add support for USB Charging to the ChromeOS Embedded Controller
- Add support for HDMI CEC to the ChromeOS Embedded Controller
- Add support for HDMI CEC to Intel HDMI
- Add support for accessory detection to Madera devices
- Allow individual pins to be configured via DT' wlf,csnaddr-pd
- Provide legacy platform specific EEPROM/Watchdog commands; rave-sp
- Fix-ups
- Trivial renaming/spelling fixes; cros_ec, da9063-*
- Convert to Managed Resources (devm_*); da9063-*, ti_am335x_tscadc
- Transition to helper macros/functions; da9063-*
- Constify; kempld-core
- Improve error path/messages; wm8994-core
- Disable IRQs locally instead of relying on USB subsystem; dln2
- Remove unused code; rave-sp
- New exports; sec-core
- Bug Fixes
- Fix possible false I2C transaction error; arizona-core
- Fix declared memory area size; hi655x-pmic
- Fix checksum type; rave-sp
- Fix incorrect default serial port configuration: rave-sp
- Fix incorrect coherent DMA mask for sub-devices; sm501
-----BEGIN PGP SIGNATURE-----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=4Yj4
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add Cirrus Logic Madera Codec (CS47L35, CS47L85 and CS47L90/91) driver
- Add ChromeOS EC CEC driver
- Add ROHM BD71837 PMIC driver
New Device Support:
- Add support for Dialog Semi DA9063L PMIC variant to DA9063
- Add support for Intel Ice Lake to Intel-PLSS-PCI
- Add support for X-Powers AXP806 to AXP20x
New Functionality:
- Add support for USB Charging to the ChromeOS Embedded Controller
- Add support for HDMI CEC to the ChromeOS Embedded Controller
- Add support for HDMI CEC to Intel HDMI
- Add support for accessory detection to Madera devices
- Allow individual pins to be configured via DT' wlf,csnaddr-pd
- Provide legacy platform specific EEPROM/Watchdog commands; rave-sp
Fix-upsL
- Trivial renaming/spelling fixes; cros_ec, da9063-*
- Convert to Managed Resources (devm_*); da9063-*, ti_am335x_tscadc
- Transition to helper macros/functions; da9063-*
- Constify; kempld-core
- Improve error path/messages; wm8994-core
- Disable IRQs locally instead of relying on USB subsystem; dln2
- Remove unused code; rave-sp
- New exports; sec-core
Bug Fixes:
- Fix possible false I2C transaction error; arizona-core
- Fix declared memory area size; hi655x-pmic
- Fix checksum type; rave-sp
- Fix incorrect default serial port configuration: rave-sp
- Fix incorrect coherent DMA mask for sub-devices; sm501"
* tag 'mfd-next-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (60 commits)
mfd: madera: Add register definitions for accessory detect
mfd: sm501: Set coherent_dma_mask when creating subdevices
mfd: bd71837: Devicetree bindings for ROHM BD71837 PMIC
mfd: bd71837: Core driver for ROHM BD71837 PMIC
media: platform: cros-ec-cec: Fix dependency on MFD_CROS_EC
mfd: sec-core: Export OF module alias table
mfd: as3722: Disable auto-power-on when AC OK
mfd: axp20x: Support AXP806 in I2C mode
mfd: axp20x: Add self-working mode support for AXP806
dt-bindings: mfd: axp20x: Add "self-working" mode for AXP806
mfd: wm8994: Allow to configure CS/ADDR Pulldown from dts
mfd: wm8994: Allow to configure Speaker Mode Pullup from dts
mfd: rave-sp: Emulate CMD_GET_STATUS on device that don't support it
mfd: rave-sp: Add legacy watchdog ping command translation
mfd: rave-sp: Add legacy EEPROM access command translation
mfd: rave-sp: Initialize flow control and parity of the port
mfd: rave-sp: Fix incorrectly specified checksum type
mfd: rave-sp: Remove unused defines
mfd: hi655x: Fix regmap area declared size for hi655x
mfd: ti_am335x_tscadc: Fix struct clk memory leak
...
Core changes:
- Add a new API for explicitly naming GPIO consumers, when needed.
- Don't let userspace set values on input lines. While we do not
think anyone would do this crazy thing we better plug the hole
before someone uses it and think it's a nifty feature.
- Avoid calling chip->request() for unused GPIOs.
New drivers/subdrivers:
- The Mediatek MT7621 is supported which is a big win for OpenWRT
and similar router distributions using this chip, as it seems
every major router manufacturer on the planet has made products
using this chip:
https://wikidevi.com/wiki/MediaTek_MT7621
- The Tegra 194 is now supported.
- The IT87 driver now supports IT8786E and IT8718F super-IO
chips.
- Add support for Rockchip RK3328 in the syscon GPIO driver.
Driver changes:
- Handle the get/set_multiple() properly on MMIO chips with
inverted direction registers. We didn't have this problem
until a new chip appear that has get/set registers AND
inverted direction bits, OK now we handle it.
- A patch series making more error codes percolate upward
properly for different errors on gpiochip_lock_as_irq().
- Get/set multiple for the OMAP driver, accelerating these
multiple line operations if possible.
- A coprocessor interface for the Aspeed driver. Sometimes a few
GPIO lines need to be grabbed by a co-processor for doing
automated tasks, sometimes they are available as GPIO lines.
By adding an explicit API in this driver we make it possible
for the two line consumers to coexist. (This work was
made available on the ib-aspeed branch, which may be appearing
in other pull requests.)
- Implemented .get_direction() and open drain in the SCH311x
driver.
- Continuing cleanup of included headers in GPIO drivers.
-----BEGIN PGP SIGNATURE-----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=4+uQ
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.19 kernel cycle.
I don't know if anything in particular stands out. Maybe the Aspeed
coprocessor thing from Benji: Aspeed is doing baseboard management
chips (BMC's) for servers etc.
These Aspeed's are ARM processors that exist inside (I guess) Intel
servers, and they are moving forward to using mainline Linux in those.
This is one of the pieces of the puzzle to achive that. They are doing
OpenBMC, it's pretty cool: https://lwn.net/Articles/683320/
Summary:
Core changes:
- Add a new API for explicitly naming GPIO consumers, when needed.
- Don't let userspace set values on input lines. While we do not
think anyone would do this crazy thing we better plug the hole
before someone uses it and think it's a nifty feature.
- Avoid calling chip->request() for unused GPIOs.
New drivers/subdrivers:
- The Mediatek MT7621 is supported which is a big win for OpenWRT and
similar router distributions using this chip, as it seems every
major router manufacturer on the planet has made products using
this chip: https://wikidevi.com/wiki/MediaTek_MT7621
- The Tegra 194 is now supported.
- The IT87 driver now supports IT8786E and IT8718F super-IO chips.
- Add support for Rockchip RK3328 in the syscon GPIO driver.
Driver changes:
- Handle the get/set_multiple() properly on MMIO chips with inverted
direction registers. We didn't have this problem until a new chip
appear that has get/set registers AND inverted direction bits, OK
now we handle it.
- A patch series making more error codes percolate upward properly
for different errors on gpiochip_lock_as_irq().
- Get/set multiple for the OMAP driver, accelerating these multiple
line operations if possible.
- A coprocessor interface for the Aspeed driver. Sometimes a few GPIO
lines need to be grabbed by a co-processor for doing automated
tasks, sometimes they are available as GPIO lines. By adding an
explicit API in this driver we make it possible for the two line
consumers to coexist. (This work was made available on the
ib-aspeed branch, which may be appearing in other pull requests.)
- Implemented .get_direction() and open drain in the SCH311x driver.
- Continuing cleanup of included headers in GPIO drivers"
* tag 'gpio-v4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (80 commits)
gpio: it87: Add support for IT8613
gpio: it87: add support for IT8718F Super I/O.
gpiolib: Avoid calling chip->request() for unused gpios
gpio: tegra: Include the right header
gpio: mmio: Fix up inverted direction registers
gpio: xilinx: Use the right include
gpio: timberdale: Include the right header
gpio: tb10x: Use the right include
gpiolib: Fix of_node inconsistency
gpio: vr41xx: Bail out on gpiochip_lock_as_irq() error
gpio: uniphier: Bail out on gpiochip_lock_as_irq() error
gpio: xgene-sb: Don't shadow error code of gpiochip_lock_as_irq()
gpio: em: Don't shadow error code of gpiochip_lock_as_irq()
gpio: dwapb: Don't shadow error code of gpiochip_lock_as_irq()
gpio: bcm-kona: Don't shadow error code of gpiochip_lock_as_irq()
gpiolib: Don't shadow error code of gpiochip_lock_as_irq()
gpio: syscon: rockchip: add GRF GPIO support for rk3328
gpio: omap: Add get/set_multiple() callbacks
gpio: pxa: remove set but not used variable 'gpio_offset'
gpio-it87: add support for IT8786E Super I/O
...
- Revert two ACPICA commits that are not needed any more (Erik
Schmauss).
- Rework property graph support in the ACPI device properties
framework to make it behave more like the analogous DT code
and update the documentation of it (Sakari Ailus).
- Change the default ACPI device status after initialization
to ACPI_STA_DEFAULT instead of 0 (Hans de Goede).
- Add a special platform driver for enumerating multiple I2C devices
hooked up to the same object in the ACPI tables (Hans de Goede).
- Fix the ACPI battery driver to avoid reporting full capacity on
systems without support for that and clean it up (Hans de Goede,
Dmitry Rozhkov, Lucas Rangit Magasweran).
- Add two system wakeup quirks to the ACPI EC driver (Aaron Ma,
Mika Westerberg).
- Add the touchscreen on Dell Venue Pro 7139 to the list of "always
present" devices to make it work (Tristian Celestin).
- Revert a special tables handling quirk for Dell XPS 9570 and
Precision M5530 which is not needed any more (Kai Heng Feng).
- Add support for a new OEM _OSI string to allow system vendors to
work around issues with NVidia HDMI audio (Alex Hung).
- Prevent the ACPI button driver from reporting excessive system
wakeup events and clean it up (Ravi Chandra Sadineni, Randy Dunlap).
- Clean up two minor code style issues in the ACPI core and GHES
handling on ARM64 (Dongjiu Geng, John Garry, Tom Todd).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=5mW8
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These revert two ACPICA commits that are not needed any more, rework
the property graphs support in ACPI to be more aligned with the
analogous DT code, add some new quirks and remove one that isn't
needed any more, add a special platform driver to enumerate multiple
I2C devices hooked up to the same device object in the ACPI tables and
update the battery and button drivers.
Specifics:
- Revert two ACPICA commits that are not needed any more (Erik
Schmauss).
- Rework property graph support in the ACPI device properties
framework to make it behave more like the analogous DT code and
update the documentation of it (Sakari Ailus).
- Change the default ACPI device status after initialization to
ACPI_STA_DEFAULT instead of 0 (Hans de Goede).
- Add a special platform driver for enumerating multiple I2C devices
hooked up to the same object in the ACPI tables (Hans de Goede).
- Fix the ACPI battery driver to avoid reporting full capacity on
systems without support for that and clean it up (Hans de Goede,
Dmitry Rozhkov, Lucas Rangit Magasweran).
- Add two system wakeup quirks to the ACPI EC driver (Aaron Ma, Mika
Westerberg).
- Add the touchscreen on Dell Venue Pro 7139 to the list of "always
present" devices to make it work (Tristian Celestin).
- Revert a special tables handling quirk for Dell XPS 9570 and
Precision M5530 which is not needed any more (Kai Heng Feng).
- Add support for a new OEM _OSI string to allow system vendors to
work around issues with NVidia HDMI audio (Alex Hung).
- Prevent the ACPI button driver from reporting excessive system
wakeup events and clean it up (Ravi Chandra Sadineni, Randy
Dunlap).
- Clean up two minor code style issues in the ACPI core and GHES
handling on ARM64 (Dongjiu Geng, John Garry, Tom Todd)"
* tag 'acpi-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (34 commits)
platform/x86: Add ACPI i2c-multi-instantiate pseudo driver
ACPI / x86: utils: Remove status workaround from acpi_device_always_present()
ACPI / scan: Create platform device for fwnodes with multiple i2c devices
ACPI / scan: Initialize status to ACPI_STA_DEFAULT
ACPI / EC: Add another entry for Thinkpad X1 Carbon 6th
ACPI: bus: Fix a pointer coding style issue
arm64 / ACPI: clean the additional checks before calling ghes_notify_sea()
ACPI / scan: Add static attribute to indirect_io_hosts[]
ACPI / battery: Do not export energy_full[_design] on devices without full_charge_capacity
ACPI / EC: Use ec_no_wakeup on ThinkPad X1 Yoga 3rd
ACPI / battery: get rid of negations in conditions
ACPI / battery: use specialized print macros
ACPI / battery: reorder headers alphabetically
ACPI / battery: drop inclusion of init.h
ACPI: battery: remove redundant old_present check on insertion
ACPI: property: graph: Update graph documentation to use generic references
ACPI: property: graph: Improve graph documentation for port/ep numbering
ACPI: property: graph: Fix graph documentation
ACPI: property: Update documentation for hierarchical data extension 1.1
ACPI: property: Document key numbering for hierarchical data extension refs
...
Core changes:
- Augment pinctrl_generic_add_group() and pinmux_generic_add_function()
to return the selector for the added group/function to the caller
and augment (hopefully) all drivers to handle this.
New subdrivers:
- Qualcomm PM8998 and PM8005 are supported in the SPMI pin
control and GPIO driver.
- Intel Ice Lake PCH (platform controller hub) support.
- NXP (ex Freescale) i.MX8MQ support.
- Berlin AS370 support.
Improvements to drivers:
- Support interrupts on the Ocelot pin controller.
- Add SPI pins to the Uniphier driver.
- Define a GPIO compatible per SoC in the Tegra driver.
- Push Tegra initialization down in the initlevels.
- Support external wakeup interrupts on the Exynos.
- Add generic clocks pins to the meson driver.
- Add USB and HSCIF pins for some Renesas PFC chips.
- Suspend/resume support in the armada-37xx.
- Interrupt support for the Actions Semiconductor S900 also
known as "owl".
- Correct the pin ordering in Cedarfork.
- Debugfs output for INTF in the mcp23s08 driver
- Avoid divisions in context save/restore in pinctrl-single.
The rest is minor bug fixes or cleanups.
-----BEGIN PGP SIGNATURE-----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=EUMW
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for v4.19:
Core changes:
- Augment pinctrl_generic_add_group() and pinmux_generic_add_function()
to return the selector for the added group/function to the caller
and augment (hopefully) all drivers to handle this
New subdrivers:
- Qualcomm PM8998 and PM8005 are supported in the SPMI pin control
and GPIO driver
- Intel Ice Lake PCH (platform controller hub) support
- NXP (ex Freescale) i.MX8MQ support
- Berlin AS370 support
Improvements to drivers:
- Support interrupts on the Ocelot pin controller
- Add SPI pins to the Uniphier driver
- Define a GPIO compatible per SoC in the Tegra driver
- Push Tegra initialization down in the initlevels
- Support external wakeup interrupts on the Exynos
- Add generic clocks pins to the meson driver
- Add USB and HSCIF pins for some Renesas PFC chips
- Suspend/resume support in the armada-37xx
- Interrupt support for the Actions Semiconductor S900 also known as
"owl"
- Correct the pin ordering in Cedarfork
- Debugfs output for INTF in the mcp23s08 driver
- Avoid divisions in context save/restore in pinctrl-single
The rest is minor bug fixes or cleanups"
* tag 'pinctrl-v4.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (69 commits)
pinctrl: nomadik: silence uninitialized variable warning
pinctrl: axp209: Fix NULL pointer dereference after allocation
pinctrl: samsung: Remove duplicated "wakeup" in printk
pinctrl: ocelot: add support for interrupt controller
pinctrl: intel: Don't shadow error code of gpiochip_lock_as_irq()
pinctrl: berlin: fix 'pctrl->functions' allocation in berlin_pinctrl_build_state
gpio: tegra: Move driver registration to subsys_init level
pinctrl: tegra: Move drivers registration to arch_init level
pinctrl: baytrail: actually print the apparently misconfigured pin
MAINTAINERS: Replace Heikki as maintainer of Intel pinctrl
pinctrl: freescale: off by one in imx1_pinconf_group_dbg_show()
pinctrl: uniphier: add spi pin-mux settings
pinctrl: cannonlake: Fix community ordering for H variant
pinctrl: tegra: define GPIO compatible node per SoC
pinctrl: intel: Do pin translation when lock IRQ
pinctrl: imx: off by one in imx_pinconf_group_dbg_show()
pinctrl: mediatek: include chained_irq.h header
pinctrl/amd: only handle irq if it is pending and unmasked
pinctrl/amd: fix gpio irq level in debugfs
pinctrl: stm32: add syscfg mask parameter
...
Merge ACPICA changes and updates of the ACPI device properties
framework for 4.19.
These revert two ACPICA commits that are not needed any more and
modify the properties graph support in ACPI to be more in-line with
the analogous DT code.
* acpica:
ACPICA: Update version to 20180629
ACPICA: Revert "iASL compiler: allow compilation of externals with paths that refer to existing names"
ACPICA: Revert "iASL: change processing of external op namespace nodes for correctness"
* acpi-property:
ACPI: property: graph: Update graph documentation to use generic references
ACPI: property: graph: Improve graph documentation for port/ep numbering
ACPI: property: graph: Fix graph documentation
ACPI: property: Update documentation for hierarchical data extension 1.1
ACPI: property: Document key numbering for hierarchical data extension refs
ACPI: property: Use data node name and reg property for graphs
ACPI: property: Allow direct graph endpoint references
ACPI: property: Make the ACPI graph API private
ACPI: property: Document hierarchical data extension references
ACPI: property: Allow making references to non-device nodes
ACPI: Convert ACPI reference args to generic fwnode reference args
This was tested on actual hardware and found to work fine, but currently
the official specifications of this chip could not be obtained to
confirm the numbers.
Signed-off-by: Leonid Bloch <lbloch@janustech.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The DIO connector on the WAFER-945GSE is interfaced to GPIO ports
on the ITE IT8718F Super I/O chipset. From the datasheet of ITE IT8718F,
the GPIO interface is identical to IT8728, so just add it
to the same case as the other chip.
Signed-off-by: Ivan Podovalov <ipodovalov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a GPIO driver so include only <linux/gpio/driver.h>.
Drop the use of GPIOF_* flags: these are for consumers, not
drivers. Just return 0/1.
Cc: Stefan Agner <stefan@agner.ch>
Cc: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The bgpio_init() takes one of two arguments to specify a register
to set the direction of the GPIO line: either dirout that
indicates that a 1 in the bit in that register sets the
corresponding line to output, or dirin which indicates that
a 1 in the bit in that register sets the corresponding line to
input. Conversely setting the bit to 0 on these will turn the
line into input and output respectively. One of these can
be defined but not both.
This means that a platform that sets a bit to 1 for output
only defines dirout and a platform that sets a bit to 0 for
output only defines dirin. In short this defines the polarity
of the direction register.
Both can also be left as NULL meaning the GPIO chip is either
input only or output only.
Tomer Maimon discovered that for get/set chips (those where the
get and set registers are defined but no separate clear register,
and specifying BGPIOF_READ_OUTPUT_REG_SET so that we say we
want to read the output value from the SET register)
we are unconditionally reading the value from the SET register
when the direction bit is 1 and from the DAT register when the
direction bit is 0, not taking the direction bit polarity into
account.
It would be expected that when the direction bit is inverted
(dirin is defined but not dirout) we read the current value from
the DAT register when the bit is 1 and from the SET register
when the bit is 0.
Currently only some versions of ATH79, brcmstb, some versions of
CLP711x, GE, IOP and Loongson use the dirin mode (a 1 in the
register means input). They are unaffected because
BGPIOF_READ_OUTPUT_REG_SET is not set on any of them. (They
do not read back the SET register to figure out the output
value.) So this is no regression with current drivers.
However the behaviour is wrong and does not work with Tomer's
new driver where he needs to use the BGIOF_READ_OUTPUT_REG_SET.
This fixes the above issue by:
- Instead of defining separate functions for the inverted case,
set up a flag in the gpio_chip that indicates that the
direction is inverted.
- Remove the special inverted functions for setting
input/output and getting the direction, rely on the flag
instead.
- Respect this flag in bgpio_get_set() and
bgpio_get_set_multiple()
Reported-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a GPIO driver so use only <linux/gpio/driver.h>.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a GPIO driver so include only <linux/gpio/driver.h>.
Cc: Richard Röjfors <richard.rojfors@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver includes the legacy <linux/gpio.h> and
<linux/of_gpio.h> but all it needs is really <linux/gpio/driver.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some platforms are not setting of_node in the driver. On these platforms
defining gpio-reserved-ranges on device tree leads to kernel crash.
It is due to some parts of the gpio core relying on the driver to set up
of_node,while other parts do themselves.This inconsistent behaviour leads
to a crash.
gpiochip_add_data_with_key() calls gpiochip_init_valid_mask() with of_node
as NULL. of_gpiochip_add() fills "of_node" and calls
of_gpiochip_init_valid_mask().
The fix is to move the assignment to chip->of_node from of_gpiochip_add()
to gpiochip_add_data_with_key().
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiochip_lock_as_irq() may return a few error codes,
bail out if it fails with corresponding returned code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiochip_lock_as_irq() may return a few error codes,
bail out if it fails with corresponding returned code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiochip_lock_as_irq() may return a few error codes,
do not shadow them by -ENOSPC and let caller to decide.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiochip_lock_as_irq() may return a few error codes,
do not shadow them by -EINVAL and let caller to decide.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiochip_lock_as_irq() may return a few error codes,
do not shadow them by -EINVAL and let caller to decide.
No functional change intended.
Cc: Hoan Tran <hotran@apm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiochip_lock_as_irq() may return a few error codes,
do not shadow them by -EINVAL and let caller to decide.
No functional change intended.
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiochip_lock_as_irq() may return a few error codes,
do not shadow them by -EINVAL and let caller to decide.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In Rockchip RK3328, the output only GPIO_MUTE pin, originally for codec
mute control, can also be used for general purpose. It is manipulated by
the GRF_SOC_CON10 register in GRF. Aside from the GPIO_MUTE pin, the HDMI
pins can also be set in the same way.
Currently this GRF GPIO controller only supports the mute pin. If needed
in the future, the HDMI pins support can also be added.
Signed-off-by: Levin Du <djw@t-chip.com.cn>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This should make applications utilizing whole banks work faster.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Torvalds