For APM calls, BX contains the device index, which is zero for
the system BIOS. Disconnect requres BX = 0.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Starting with kernel 2.6.23-rc1, the i386 APM driver fails
on several of my machines with the message:
apm: BIOS not found
This happens because of a bug in the i386 boot code rewrite
from assembler to C. The original assembly code had the
following code in its APM BIOS presence test (boot/setup.S):
andw $0x02, %cx # Is 32 bit supported?
je done_apm_bios # No 32-bit, no (good) APM BIOS
That is, the code bails out if bit 2 is zero.
In the new C version, this is coded as (boot/apm.c):
if (cx & 0x02) /* 32 bits supported? */
return -1;
Here we see that the test has been accidentally inverted.
The fix is to negate the test. I've verified that this
allows the APM driver to work again on my affected machines.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: Kconfig: remove CONFIG_ACPI_SLEEP from source
ACPI: quiet ACPI Exceptions due to no _PTC or _TSS
ACPI: Remove references to ACPI_STATE_S2 from acpi_pm_enter
ACPI: Kconfig: always enable CONFIG_ACPI_SLEEP on X86
ACPI: Kconfig: fold /proc/acpi/sleep under CONFIG_ACPI_PROCFS
ACPI: Kconfig: CONFIG_ACPI_PROCFS now defaults to N
ACPI: autoload modules - Create __mod_acpi_device_table symbol for all ACPI drivers
ACPI: autoload modules - Create ACPI alias interface
ACPI: autoload modules - ACPICA modifications
ACPI: asus-laptop: Fix failure exits
ACPI: fix oops due to typo in new throttling code
ACPI: ignore _PSx method for hotplugable PCI devices
ACPI: Use ACPI methods to select PCI device suspend state
ACPI, PNP: hook ACPI D-state to PNP suspend/resume
ACPI: Add acpi_pm_device_sleep_state helper routine
ACPI: Implement the set_target() callback from pm_ops
Parse the machvec command line option outside of the early_param()
so that ia64_mv is set before any console intialisation that
may result from early_param parsing.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This change fixes a panic when assign_irq_vector(irq) is called with
irq = AUTO_ASSIGN.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Currently most of the m68knommu cpu/board setup files are handling
the setup of fixed boot parameters (via CONFIG_BOOTPARAM) themselves.
Move all this into the common setup code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add configure support for the Intec Wildfire and WildFireMod boards.
Signed-Off-By: Steve Bennett <steveb@workware.net.au>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is useless to preserve THREAD_SR in `resume'. The real user's sr
is actually in the stack. We also don't need to disable interrupts :
we'll never be in an invalid state, the sp switch is atomic.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add build support for the new Arcturus boards.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Need to explicitly include linux/device.h.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add configure support for the Arcturus UC5272 and UC5282 boards.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We didn't actually propogate the flag we pass into setup_indirect_pci()
to set indirect_type and thus were getting the wrong endianness if
PPC_INDIRECT_TYPE_BIG_ENDIAN was set.
Also, we need to or in additional flags rather than just doing a
direct assignment.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
As it was a synonym for (CONFIG_ACPI && CONFIG_X86),
the ifdefs for it were more clutter than they were worth.
For ia64, just add a few stubs in anticipation of future
S3 or S4 support.
Signed-off-by: Len Brown <len.brown@intel.com>
This patch removes old dead code:
- kill off sh73180 cpu support
- get rid of broken solution engine 73180 board support
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The code in arch/sh/kernel/cpu/irq/pint.c doesn't compile, so let's
get rid of it to make space for a future pint implementation on top
of intc.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The first 1MB of P3 space was reserved and used for page colouring,
as we've reworked that to use fixmaps, we can reclaim the space and
hand it back to VMALLOC_START.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We can't mark the whole thing init because there are dependencies
in bootloaders that assume that _start, or whatever the image
entry value, is 2 instructions before the "HdrS" signature.
In fact, TILO assumes this entry is always at 0x4000, yikes!
Also, right after the bootloader info area there are OBP strings and
values that get used later in the boot process, and those are not all
provably .init yet.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for arch/powerpc, specifically for the prpmc2800 platform.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Sparc optimized memset (arch/sparc/lib/memset.S) does not fill last
byte of the memory area, if area size is less than 8 bytes and start
address is not word (4-bytes) aligned.
Here is code chunk where bug located:
/* %o0 - memory address, %o1 - size, %g3 - value */
8:
add %o0, 1, %o0
subcc %o1, 1, %o1
bne,a 8b
stb %g3, [%o0 - 1]
This code should write byte every loop iteration, but last time delay
instruction stb is not executed because branch instruction sets
"annul" bit.
Patch replaces bne,a by bne instruction.
Error can be reproduced by simple kernel module:
--------------------
#include <linux/module.h>
#include <linux/config.h>
#include <linux/kernel.h>
#include <linux/errno.h>
#include <string.h>
static void do_memset(void **p, int size)
{
memset(p, 0x00, size);
}
static int __init memset_test_init(void)
{
char fooc[8];
int *fooi;
memset(fooc, 0xba, sizeof(fooc));
do_memset((void**)(fooc + 3), 1);
fooi = (int*) fooc;
printk("%08X %08X\n", fooi[0], fooi[1]);
return -1;
}
static void __exit memset_test_cleanup(void)
{
return;
}
module_init(memset_test_init);
module_exit(memset_test_cleanup);
MODULE_LICENSE("GPL");
EXPORT_NO_SYMBOLS;
--------------------
Signed-off-by: Alexander Shmelev <ashmelev@task.sun.mcst.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes boot failures when the build-id LD option is
actually used, because without it we end up with multiple
PT_LOAD sections which the SILO boot loader cannot handle.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'request-queue-t' of git://git.kernel.dk/linux-2.6-block:
[BLOCK] Add request_queue_t and mark it deprecated
[BLOCK] Get rid of request_queue_t typedef
spufs.h now has two enums for the sched_flags leading to identical
values for SPU_SCHED_WAS_ACTIVE and SPU_SCHED_NOTIFY_ACTIVE. Merge
them into a single enum as they were in the IBM development tree.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2.6.23-rc1 turned up another batch of references from non-__init code to
__init code. In most cases, these were missing __init annotations. In one
case (os_drop_memory), the annotation was present but wrong.
init_maps is __init, but for some reason was being very careful about the
mechanism by which it allocated memory, checking whether it was OK to use
kmalloc (at this point in the boot, it definitely isn't) and using either
alloc_bootmem_low_pages or kmalloc/vmalloc. So, the kmalloc/vmalloc code is
removed.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Restructure do_aio thanks to commments from Ulrich and Al.
Uli started this by seeing that UML's initialization of a struct iocb
initialized fields that it shouldn't.
Al followed up by adding the following cleanups:
eliminating a variable by just using an anonymous structure in
its place.
hoisting a duplicated line out of the switch.
simplifying the error checking at the end.
I added a severity to the printk.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In 2.6.23-rc1, i386 fiddled its string support such that UML started getting
undefined references from modules. The UML asm/string.h was including the
i386 string.h, which defined __HAVE_ARCH_STR*, but the corresponding
implementations weren't being pulled in.
This is fixed by adding arch/i386/lib/string.h to the list of host
architecture files to be pulled in to UML.
A complication is that the libc exports file assumed that the generic strlen
and strstr weren't in use (i.e. __HAVE_ARCH_STR is defined), then they aren't
exported. This is untrue for strlen, which is exported in either case, so
this logic is not needed.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver previously registered its platform device data in its own
init function--that's bogus. Move that code to platform-specific
code in arch/ppc. This is being done so that the platform code can
decide at runtime whether to initialize this driver or not.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Added the MPC85xx PCI device IDs that we need for the quirks we have.
Also, fixed the MPC8567E, MPC8567 device IDs which had the wrong value.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Also add 8641/8641D device IDs as well.
All of which already exist or have been submitted to
The Linux PCI ID Repository at:
http://pci-ids.ucw.cz/
CC-to: pci-ids@ucw.cz
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added the P2P bridge present on the Arcadia base board and moved the VIA
Southbridge behind the bridge to reflect its actual position in the bus
organization. Added the RTC that's in the VIA Southbridge and expanded
the ranges array for the SOC node to allow proper address translation of
the RTC registers.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Setting the host bridge @8000 as primary. Also fixing a bug in
setting the USB interrupt numbers.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The interrupts of an E100 card inserted in PCI slot 4 may be on at bootup.
The resulting interrupt flood interacts with the 8259 cascade handler and
prevents proper boot up. There is a quirk for the E100 that will disable
the E100's interrupts but to use it, the 8259 cascade hookup must be
delayed until after the quirk has run. This patch delays the 8259 cascade
hookup by registering a device_initcall() which runs after the PCI quirk
for the E100.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
__INIT directive just before kernel_entry was ignored for most platforms.
This patch fixes it and get rid of this warning:
WARNING: vmlinux.o(.text+0x478): Section mismatch: reference to .init.text:start_kernel (between '_stext' and 'run_init_process')
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We can make resources for platform_device_register_simple() "static
__initdata".
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replaces the deprecated __attribute_used__ with __used. Also makes some
style adjustments to abide by the kernel coding conventions.
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
> WARNING: vmlinux.o(.text+0xbf20): Section mismatch: reference to
> .init.text:prom_free_prom_memory (between 'free_initmem' and 'copy_from_user_page')
prom_free_prom_memory() is called _before_ freeing init sections, so
it is false positive. __init_refok can be used for such cases.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
make ARCH_PXA select GENERIC_CLOCKEVENTS to fix the
building issue due to merge of clockevents based PXA
timer
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some of the code has been gradually transitioned to using the proper
struct request_queue, but there's lots left. So do a full sweet of
the kernel and get rid of this typedef and replace its uses with
the proper type.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The current SH DMA API is somewhat broken, not correctly matching
virtual channel to the correct SH DMAC. This wasn't noticeable when
using g2 DMA for the sound driver - one channel 0 is as good as any
other! - but caused the pvr2 driver to fail.
This patch fixes the pvr2 problem and consequently fixes the sound
driver to ensure it continues to function.
Signed-off by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This wires up kmap_coherent() and kunmap_coherent() on SH-4, and
moves away from the p3map_mutex and reserved P3 space, opting to
use fixmaps for colouring instead.
The copy_user_page()/clear_user_page() implementations are moved
to this, which fixes the nasty blowups with spinlock debugging
as a result of having some of these calls nested under the page
table lock.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The current 85xxCDS restart code fails to reset the PCI bus which can
lead to odd behavior after the restart. This patch uses the VIA Super
Southbridge to perform a PCI reset which will reset the entire system.
NOTE: Since the VIA chip is behind a PCI-to-PCI bridge which can be
disabled with a switch setting, it may not be possible to perform the
PCI bus reset. In this case, the code defaults to the previous restart
mechanism.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale MPC8555CDS and MPC8548CDS reference hardware has a legacy
8259 interrupt controller pair contained within a VIA VT82C686B Southbridge
on the main carrier board. The processor complex plugs into the carrier
card using a PCI slot which limits the available interrupts to the
INTA-INTD PCI interrupts. The output of the 8259 cascade pair is routed
through a gate array and connected to the PCI INTA interrupt line.
The normal interrupt chaining hook (set_irq_chained_handler) does
not allow sharing of the chained interrupt which prevents the
use of PCI INTA by PCI devices. This patch allows the 8259 cascade
pair to share their interrupt line with PCI devices.
NOTE: The addition of the .end routine for the MPIC is not strictly
necessary for this patch. It's there so this code will run from within
the threaded interrupt context used by the Real Time patch.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some set of 85xx platforms have PCI-X controllers. The old arch/ppc
code setup these controllers and we haven't moved it over to arch/powerpc.
We use the PCI-X Capabilties to know if we are in PCI-X mode instead
of the Global Utilities PORDEVSR.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For the Freescale PCIe PHBs Not all firmwares setup the virtual P2P
bridge registers properly. Make sure they get setup based on what
the struct pci_controller got from the device tree.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We need the ability to set P2P bridge registers to properly setup the virtual
P2P bridges that exist in PCIe controllers for some of the embedded setups.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add basic support for the PCIe PHB and enable the ULI bridge.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Make it so we do a runtime check to know if we need to write cfg_addr
as big or little endian. This is needed if we want to allow 86xx support
to co-exist in the same kernel as other 6xx PPCs.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We don't use setup_indirect_pci_nomap in arch/powerpc and it appears
the users that needed it from arch/ppc are now using setup_indirect_pci.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The newer Arcadia boards for CDS have an FPGA that shows up on PCI
however isn't a real PCI device. Add a quirk to just ignore the
FPGA.
This is based on the following patch from Andy & York:
http://ozlabs.org/pipermail/linuxppc-dev/2007-February/032042.html
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On the 85xx/86xx PCIe controllers if there is no device connected to the
PHB we will still allocate a pci_bus for downstream bus of the virtual
P2P bridge. However the resources allocated to the downstream bus are not
correct and so we just mimic the resources from the upstream pci_bus.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Switch the 85xx platform over to using the FSL generic PCI code. This
gets ups PCIe support in addition to base PCI support.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Updated the 83xx & 85xx device tree PCI related compartible property.
Used the following compatible properties:
PCI "fsl,mpc8349-pci"
PCI "fsl,mpc8540-pci"
PCI-X: "fsl,mpc8540-pcix"
PCIe: "fsl,mpc8548-pcie"
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add 8548 CDS PCI express controller node and PCI-X device node. The current
dts file is suitable for 8548 Rev 2.0 board with Arcadia 3.1.
This kind of board combination is the most popular.
Used the following compatible properties:
PCI "fsl,mpc8540-pci"
PCI-X: "fsl,mpc8540-pcix"
PCIe: "fsl,mpc8548-pcie"
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use the PCI capabilities to determine if we are PCIe PHB. Also use
PPC_INDIRECT_TYPE_NO_PCIE_LINK since the Freescale PCIe controllers
will lock the system if they don't have link and you try to do a config
access to anything but the PHB.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added PPC_INDIRECT_TYPE_NO_PCIE_LINK flag to the indirect pci handling
code to ensure that we don't talk to any device other than the PHB
if we don't have PCIe link. Some controllers will lockup if they try
to do a config cycle to any device on the bus except the PHB.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added early_find_capability that wraps pci_bus_find_capability and uses
fake_pci_bus() to allow us to call it before we've fully setup the
pci_controller.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rewrite the Freescale PCI code to support PCI on 83xx/85xx/86xx and
PCIe on 85xx/86xx.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move
arch/powerpc/platforms/86xx/pci.c -> arch/powerpc/sysdev/fsl_pci.c
arch/powerpc/sysdev/fsl_pcie.h -> arch/powerpc/sysdev/fsl_pci.h
as the base to unify 83xx/85xx/86xx pci and pcie.
Add CONFIG_FSL_PCI to build fsl_pci.c for Freescale pci and pcie option.
The code still works for 86xx platforms.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This avoids a conflict with sparse builds.
Reported by Alexey Dobriyan, fix suggested by Al Viro
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that the last inlined instances are gone, all that is left to do
is turning disable_irq_nosync on arm26 and m68k from defines to aliases
and we are all set - we can make these externs in linux/interrupt.h
uncoditional and kill remaining instances in asm/irq.h
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: Convert from struct class_device to struct device
leds: leds-gpio for ngw100
leds: Add warning printks in error paths
leds: Fix trigger unregister_simple if register_simple fails
leds: Use menuconfig objects II - LED
leds: Teach leds-gpio to handle timer-unsafe GPIOs
leds: Add generic GPIO LED driver
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Clean up duplicate includes in drivers/macintosh/
[POWERPC] Quiet section mismatch warning on pcibios_setup
[POWERPC] init and exit markings for hvc_iseries
[POWERPC] Quiet section mismatch in hvc_rtas.c
[POWERPC] Constify of_platform_driver match_table
[POWERPC] hvcs: Make some things static and const
[POWERPC] Constify of_platform_driver name
[POWERPC] MPIC protected sources
[POWERPC] of_detach_node()'s device node argument cannot be const
[POWERPC] Fix ARCH=ppc builds
[POWERPC] mv64x60: Use mutex instead of semaphore
[POWERPC] Allow smp_call_function_single() to current cpu
[POWERPC] Allow exec faults on readable areas on classic 32-bit PowerPC
[POWERPC] Fix future firmware feature fixups function failure
[POWERPC] fix showing xmon help
[POWERPC] Make xmon_write accept a const buffer
[POWERPC] Fix misspelled "CONFIG_CHECK_CACHE_COHERENCY" Kconfig option.
[POWERPC] cell: CONFIG_SPE_BASE is a typo
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (77 commits)
ACPI: Populate /sys/firmware/acpi/tables/
ACPI: create CONFIG_ACPI_DEBUG_FUNC_TRACE
ACPI: update ACPI proc I/F removal schedule
ACPI: update feature-removal-schedule.txt, /sys/firmware/acpi/namespace is gone
ACPI: export ACPI events via acpi_mc_group multicast group
ACPI: fix empty macros found by -Wextra
ACPI: drivers/acpi/pci_link.c: lower printk severity
sony-laptop: Fix event reading in sony-laptop
sony-laptop: Add Vaio FE to the special init sequence
sony-laptop: Make the driver use MSC_SCAN and a setkeycode and getkeycode key table.
sony-laptop: Invoke _INI for SNC devices that provide it
sony-laptop: Add support for recent Vaios Fn keys (C series for now)
sony-laptop: map wireless switch events to KEY_WLAN
sony-laptop: add new SNC handlers
ACPI: thinkpad-acpi: add locking to brightness subdriver
ACPI: thinkpad-acpi: bump up version to 0.15
ACPI: thinkpad-acpi: make EC-based thermal readings non-experimental
ACPI: thinkpad-acpi: make sure DSDT TMPx readings don't return +128
ACPI: thinkpad-acpi: react to Lenovo ThinkPad differences in hot key
ACPI: thinkpad-acpi: allow use of CMOS NVRAM for brightness control
...
Get rid of warnings like
WARNING: vmlinux.o(.bootstrap.text+0x1a8): Section mismatch: reference to .init.text:x86_64_start_kernel (between 'initial_code' and 'init_rsp')
- Move initialization code into .text.head like i386 because modpost knows about this already
- Mark initial_code .initdata
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix following warning:
WARNING: vmlinux.o(.text+0x188ea): Section mismatch: reference to .init.text:__alloc_bootmem_core (between 'alloc_bootmem_high_node' and 'get_gate_vma')
alloc_bootmem_high_node() is only used from __init scope so declare it __init.
And in addition declare the weak variant __init too.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix following warnings:
WARNING: vmlinux.o(.text+0x945e): Section mismatch: reference to .init.text:__set_fixmap (between 'hpet_arch_init' and 'hpet_mask_rtc_irq_bit')
WARNING: vmlinux.o(.text+0x9474): Section mismatch: reference to .init.text:__set_fixmap (between 'hpet_arch_init' and 'hpet_mask_rtc_irq_bit')
hpet_arch_init is only used from __init context so mark it __init.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The performance counters on K7 are only 48 bits wide, so using bit 63 to
check if the counter overflowed is wrong. Let's use bit 47 instead.
Signed-off-by: Björn Steinbrink <B.Steinbrink@gmx.de>
Cc: Don Zickus <dzickus@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I got an oops while booting a 32bit kernel on KVM because it doesn't
implement performance counters used by the NMI watchdog. Handle this
case.
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Due to index register access ordering problems, when using macros a line
like this fails (and does nothing):
setCx86(CX86_CCR2, getCx86(CX86_CCR2) | 0x88);
With inlined functions this line will work as expected.
Note about a side effect: Seems on Geode GX1 based systems the
"suspend on halt power saving feature" was never enabled due to this
wrong macro expansion. With inlined functions it will be enabled, but
this will stop the TSC when the CPU runs into a HLT instruction.
Kernel output something like this:
Clocksource tsc unstable (delta = -472746897 ns)
This is the 3rd version of this patch.
- Adding missed arch/i386/kernel/cpu/mtrr/state.c
Thanks to Andres Salomon
- Adding some big fat comments into the new header file
Suggested by Andi Kleen
AK: fixed x86-64 compilation
Signed-off-by: Juergen Beisert <juergen@kreuzholzen.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kstat_irqs(0) includes the count of interrupt 0 from all cpus, not just
the current cpu. The updated interrupt 0 on other cpus can stop the
nmi_watchdog from tripping, so only include the current cpu's int 0.
Signed-off-by: Keith Owens <kaos@ocs.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This mainly changes the nops for alternative, so not very revolutionary.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previously this flag was only used on 32bit, but some shared code can use
it now.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a machine check or NMI occurs while multiple byte code is patched
the CPU could theoretically see an inconsistent instruction and crash.
Prevent this by temporarily disabling MCEs and returning early in the
NMI handler.
Based on discussion with Mathieu Desnoyers.
Cc: Mathieu Desnoyers <compudj@krystal.dyndns.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reenable kprobes and alternative patching when the kernel text is write
protected by DEBUG_RODATA
Add a general utility function to change write protected text. The new
function remaps the code using vmap to write it and takes care of CPU
synchronization. It also does CLFLUSH to make icache recovery faster.
There are some limitations on when the function can be used, see the
comment.
This is a newer version that also changes the paravirt_ops code.
text_poke also supports multi byte patching now.
Contains bug fixes from Zach Amsden and suggestions from Mathieu
Desnoyers.
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Mathieu Desnoyers <compudj@krystal.dyndns.org>
Cc: Zach Amsden <zach@vmware.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch uses the read and write functions provided at system.h
for control registers instead of writting raw assembly over and
over again in .c files. Functions to manipulate cr2 and cr8 were
provided, as they were lacking.
Also, removed some extra space after closing brackets
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch makes the i386 behave the same way that x86_64 does when a
segfault happens. A line gets printed to the kernel log so that tools
that need to check for failures can behave more uniformly between
debug.show_unhandled_signals sysctl variable to 0 (or by doing echo 0 >
/proc/sys/debug/exception-trace)
Also, all of the lines being printed are now using printk_ratelimit() to
deny the ability of DoS from a local user with a program like the
following:
main()
{
while (1)
if (!fork()) *(int *)0 = 0;
}
This new revision also includes the fix that Andrew did which got rid of
new sysctl that was added to the system in earlier versions of this.
Also, 'show-unhandled-signals' sysctl has been renamed back to the old
'exception-trace' to avoid breakage of people's scripts.
AK: Enabling by default for i386 will be likely controversal, but let's see what happens
AK: Really folks, before complaining just fix your segfaults
AK: I bet this will find a lot of silent issues
Signed-off-by: Masoud Sharbiani <masouds@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
[ Personally, I've found the complaints useful on x86-64, so I'm all for
this. That said, I wonder if we could do it more prettily.. -Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a mismerge in commit 8b6f50ef1d5cc86b278eb42bc91630fad455fb10:
"spufs: make signal-notification files readonly for NOSCHED contexts",
where structs got duplicated.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move register and other definitions out of the
include/asm-arm/arch-s3c2410 into the the arch
directories of include/asm-arm/plat-s3c24xx and
include/asm-arm/plat-s3c.
This move is in preperation of the merging of
s3c2400 and s3c6400.
The following git mv commands are needed before
this patch can be applied:
git mv include/asm-arm/arch-s3c2410/regs-ac97.h include/asm-arm/plat-s3c/regs-ac97.h
git mv include/asm-arm/arch-s3c2410/regs-adc.h include/asm-arm/plat-s3c/regs-adc.h
git mv include/asm-arm/arch-s3c2410/regs-iis.h include/asm-arm/plat-s3c24xx/regs-iis.h
git mv include/asm-arm/arch-s3c2410/regs-spi.h include/asm-arm/plat-s3c24xx/regs-spi.h
git mv include/asm-arm/arch-s3c2410/regs-udc.h include/asm-arm/plat-s3c24xx/regs-udc.h
git mv include/asm-arm/arch-s3c2410/udc.h include/asm-arm/plat-s3c24xx/udc.h
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the static maps for the LCD and USB devices.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename the S3C24XX configuration options for the watchdog
boot controls for moving to the arch/arm/plat-s3c moves.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename DEBUG_S3C2410_PORT to DEBUG_S3C_PORT as well as
DEBUG_S3C2410_UART to DEBUG_S3C_UART as part of the updates
to moving to plat-s3c for S3C base support.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename CONFIG_S3C2410_LOWLEVEL_UART_PORT to be
CONFIG_S3C_LOWLEVEL_UART_PORT as we move to using
plat-s3c for base of S3C operations.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the Kconfig to create configuration options based on which
CPUs are supported for the low level serial code. This means that
the debug macros can be optimised for the type(s) of CPU that are
being used.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Create the initial arch/arm/plat-s3c directory and start
linking it into the arch/arm build heirarchy ready to
receive the generic parts of the S3C24XX support to be
used when adding S3C6400 devices.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch moves items of the s3c24xx support into
a new plat-s3c directory for items that use the
s3c24xx support but are not directly s3c24xx
compatible, such as the s3c2400 and s3c6400.
git mv commands:
git mv include/asm-arm/arch-s3c2410/iic.h include/asm-arm/plat-s3c/iic.h
git mv include/asm-arm/arch-s3c2410/nand.h include/asm-arm/plat-s3c/nand.h
git mv include/asm-arm/arch-s3c2410/regs-iic.h include/asm-arm/plat-s3c/regs-iic.h
git mv include/asm-arm/arch-s3c2410/regs-nand.h include/asm-arm/plat-s3c/regs-nand.h
git mv include/asm-arm/arch-s3c2410/regs-rtc.h include/asm-arm/plat-s3c/regs-rtc.h
git mv include/asm-arm/arch-s3c2410/regs-serial.h include/asm-arm/plat-s3c/regs-serial.h
git mv include/asm-arm/arch-s3c2410/regs-timer.h include/asm-arm/plat-s3c/regs-timer.h
git mv include/asm-arm/arch-s3c2410/regs-watchdog.h include/asm-arm/plat-s3c/regs-watchdog.h
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the foundation pieces for
the Freescale MXC platforms, including
i.MX2 and i.MX3 based systems.
The bare-bones MX31 support in this patch
boots to the rootdev panic with 8250 serial
console configured "console=ttyS0,115200".
It assumes that Redboot is the boot loader.
Signed-off-by: Quinn Jensen <quinn.jensen@freescale.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reimplements arch/arm/mach-pxa/time.c using a clock_event_device based
on OSMR0. Tested on PXA270, linux-2.6.22+arm:pxa patches.
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
WARNING: vmlinux.o(.text+0x1cefcc): Section mismatch: reference to .init.text:.pcibios_setup (between '.pci_setup' and '.pci_init')
pci_setup() is marked __devinit and calls pcibios_setup.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some HW platforms, such as the new cell blades, requires some MPIC sources
to be left alone by the operating system. This implements support for
a "protected-sources" property in the mpic controller node containing a list
of source numbers to be protected against operating system interference.
For those interested in the gory details, the MPIC on the southbridge of
those blades has some of the processor outputs routed to the cell, and
at least one routed as a GPIO to the service processor. It will be used
in the GA product for routing some of the southbridge error interrupts
to the service processor which implements some of the RAS stuff, such
as checkstopping when fatal errors occurs before they can propagate.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
...since it modifies it (when it sets the OF_DETACHED flag).
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This removes the requirement for callers to get_cpu() to check in simple
cases. i386 and x86_64 already received a similar treatment.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Classic 32-bit PowerPC CPUs, and the early 64-bit PowerPC CPUs, don't
provide a way to prevent execution from readable pages, that is, the
MMU doesn't distinguish between data reads and instruction reads,
although a different exception is taken for faults in data accesses
and instruction accesses.
Commit 9ba4ace39f, in the course of
fixing another bug, added a check that meant that a page fault due
to an instruction access would fail if the vma did not have the
VM_EXEC flag set. This gives an inconsistent enforcement on these
CPUs of the no-execute status of the vma (since reading from the page
is sufficient to allow subsequent execution from it), and causes old
versions of ppc32 glibc (2.2 and earlier) to fail, since they rely
on executing the word before the GOT but don't have it marked
executable.
This fixes the problem by allowing execution from readable (or writable)
areas on CPUs which do not provide separate control over data and
instruction reads.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
Move firmware feature initialisation from pSeries_init_early to the
earlier pSeries_probe_hypertas so they are initialised before firmware
feature fixups are applied.
Currently firmware feature sections are only used for iSeries which
initialises the these features much earlier. This is a bug in waiting
on pSeries.
Also adds some whitespace fixups.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In some configuration, xmon help string is larger than xmon_printf
buffer. We need not to use printf. This patch adds xmon_puts and
change to use it to show help string.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Because xmon_write doesn't change the buffer, we should add 'const'
qualifier to the argument which points it.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The config symbol for SPE support is called CONFIG_SPU_BASE, not
CONFIG_SPE_BASE.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: ERROR: "sys_ioctl" [arch/sparc64/solaris/solaris.ko] undefined!
[SPARC32]: Make PAGE_SHARED a read-mostly variable.
[SPARC32]: Take enable_irq/disable_irq out of line.
[SPARC32]: clean include/asm-sparc/irq.h
[SPARC32]: Fix rounding errors in ndelay/udelay implementation.
From: Christoph Hellwig <hch@infradead.org>
On Fri, Jul 20, 2007 at 09:24:42AM -0400, Horst H. von Brand wrote:
> When building v2.6.22-3478-g275afca on sparc64 (.config attached) I get:
>
> MODPOST vmlinux
> Building modules, stage 2.
> MODPOST 463 modules
> ERROR: "sys_ioctl" [arch/sparc64/solaris/solaris.ko] undefined!
Sorry, my fault.
It looked to me like sparc64 exports sys_ioctl on it's own, but it
only exports compat_sys_ioctl on it's own.
Signed-off-by: David S. Miller <davem@davemloft.net>
Move stuff used only by arch/sparc/kernel/* into arch/sparc/kernel/irq.h
and into individual files in there (e.g. macros internal to sun4m_irq.c,
etc.)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
__ndelay and __udelay have not been delayung >= specified time.
The problem with __ndelay has been tacked down to the rounding of the
multiplier constant. By changing this, delays > app 18us are correctly
calculated.
The problem with __udelay has also been tracked down to rounding issues.
Changing the multiplier constant (to match that used in sparc64) corrects
for large delays and adding in a rounding constant corrects for trunctaion
errors in the claculations.
Many short delays will return without looping. This is not an error as there
is the fixed delay of doing all the maths to calculate the loop count.
Signed-off-by: Mark Fortescue <mark@mtfhpc.demon.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces struct pci_sysdata to x86 and x86-64, and
converts the existing two users (NUMA, Calgary) to use it.
This lays the groundwork for having other users of sysdata, such as
the PCI domains work.
The Calgary bits are tested, the NUMA bits just look ok.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes k8topology multicore aware instead of limited to signle- and
dual-core CPUs. It uses the CPUID to be more future proof.
Signed-off-by: Joachim Deguara <joachim.deguara@amd.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Leftovers from the removal of the more general (but abandoned) SMP
alternatives.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dead or misnamed CONFIG_BALANCED_IRQ_DEBUG found by Robert P. J. Day.
It's not a Kconfig variable.
Since this debug code is ancient, I suggest to get rid of this
misleading CONFIG_ macro by deleting all of this debug code.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Robert P. J. Day" <rpjday@mindspring.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Insert HPET resources after pci probing has been completed in order to
avoid resource conflicts with PCI resource reservation. With this change
the HPET firmware resources will be identified, but it should also not
cause issues when the HPET address falls on a BAR in a PCI device, and the
PCI enumeration cannot reserve the resources.
Signed-off-by: Aaron Durbin <adurbin@google.com>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This builds upon the existing geode infrastructure, but adds southbridge
support, some GPIO functions, and a header file (asm-i386/geode.h) with some
useful GX/LX detection tests.
The majority of this code was written by Jordan Crouse.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Users that use kernel log filtering (e.g. via syslogd or a proprietry method)
wouldn't like to see warning prints that are not really warnings.
Signed-off-by: Dan Aloni <da-x@monatomic.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
get_vm_area always returns an area with an adjacent guard page. That guard
page is included in vm_struct.size. iounmap uses vm_struct.size to
determine how much address space needs to have change_page_attr applied to
it, which will BUG if applied to the guard page.
This patch adds a helper function - get_vm_area_size() in linux/vmalloc.h -
to return the actual size of a vm area, and uses it to make iounmap do the
right thing. There are probably other places which should be using
get_vm_area_size().
Thanks to Dave Young <hidave.darkstar@gmail.com> for debugging the
problem.
[ Andi, it wasn't clear to me whether x86_64 needs the same fix. ]
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Dave Young <hidave.darkstar@gmail.com>
Cc: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
setup_pit_timer is declared in asm-i386/timer.h. Move it to the pit header
file, so it can be used by x86_64 as well.
Move also the PIT constants.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I fixed this in x86_64. Looks like the kind of thing that will break voyager
on i386.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the volatile in apic. We have a cpu_relax() in the wait loop. Fix a
coding style issue while at it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When NUMA emulation succeeds, acpi_numa needs to be set to -1 so that
srat_disabled() will always return true. We won't be calling
acpi_scan_nodes() or registering the true nodes we've found.
[hugh@veritas.com: Fix x86_64 CONFIG_NUMA_EMU build: acpi_numa needs CONFIG_ACPI_NUMA]
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
e820_hole_size() now uses the newly extracted helper function,
e820_find_active_region(), to determine the size of usable RAM in a range of
PFN's.
This was previously broken because of two reasons:
- The start and end PFN's of each e820 entry were not properly rounded
prior to excluding those entries in the range, and
- Entries smaller than a page were not properly excluded from being
accumulated.
This resulted in emulated nodes being incorrectly mapped to ranges that
were completely reserved and not candidates for being registered as
active ranges.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For K8 system: 4G RAM with memory hole remapping enabled, or more than 4G
RAM installed. when using kexec to load second kernel. In the second
kernel, when mem is allocated for GART, it will do the memset for clear, it
will cause restart, because some device still used that for dma. solution
will be:
in second kernel: disable that at first before we try to allocate mem for
it. or in the first kernel: do disable that before shutdown.
Andi/Eric/Alan prefer to second one for clean shutdown in first kernel.
Andi also point out need to consider to AGP enable but mem less 4G case
too.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This function is called via dma_ops->.., so change it to static
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace the pcspkr private PIT lock by the global PIT lock to serialize the
PIT access all over the place.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During a VM oom condition, kill all threads in the process group.
We have had complaints where a threaded application is left in a bad state
after one of it's threads is killed when we hit a VM: out_of_memory condition.
Killing just one of the process threads can leave the application in a bad
state, whereas killing the entire process group would allow for the
application to restart, or otherwise handled, and makes it very obvious that
something has gone wrong.
This change allows the entire process group to be taken down, rather than just
the one thread.
Signed-off-by: Will <will_schmidt@vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some interrupt entry points are currently defined in i8259.c They probably
belong in a header. Right now, their only user is init_IRQ, justifying
their declaration in-file. But when virtualization comes in, we may be
interested in using that functions in late initializations.
Signed-off-by: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We are seeing corruption of the decompressed kernel. It is suspected that
this is platform specific as it has yet to be seen on any other x86. Move
the kernel to the 16MB boundary.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove unneeded test of task != NULL from
arch/i386/kernel/traps.c::dump_trace()
At the start of the function we have this test:
if (!task)
task = current;
so further down there's no need to test 'task'.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PAE is useful for more than supporting more than 4GB RAM. It supports
expanded swapspace and NX executable protections. Some users may want NX
or expanded swapspace support without the overhead or instability of
highmem. For these reasons, the following patch divorces CONFIG_X86_PAE
from CONFIG_HIGHMEM64G.
Cc: Mark Lord <lkml@rtr.ca>
Signed-off-by: William Irwin <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some systems have a HPET which is not incrementing, which leads to a
complete hang. Detect it during HPET setup.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following patch enables reboot through BIOS on the Dell Optiplex 745
Small Form Factor base, on which reboot hangs. The larger form factor does
not require this, hence the match on DMI_BOARD_NAME.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On some systems the ACPI NVS area is located in the first 1 MB of RAM and
it is overwritten by the i386 code during the restore after hibernation.
This confuses the ACPI platform firmware that doesn't update the AC adapter
status appropriately as a result
(http://bugzilla.kernel.org/show_bug.cgi?id=7995).
The solution is to register the reserved memory in the first 1 MB as
'nosave', so that swsusp doesn't touch it during the restore. Also, this
has been done on x86_64 for a long time now, so this patch makes the i386
restore code behave like the x86_64 one.
[akpm@linux-foundation.org: build fix]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix following warning:
WARNING: arch/i386/kernel/built-in.o(.init.text+0x3818): Section mismatch: reference to .exit.text:cache_remove_dev (between 'cacheinfo_cpu_callback' and 'cache_sysfs_init')
It points out that a function marked __cpuexit is calling a function marked
__cpuinit => oops.
The call happens only in an error-condition which may explain why we have
not seen it before.
The offending function was not used anywhere else - so marked it __cpuexit.
Note: This warning triggers only with a local copy of modpost
but that version will soon be pushed out.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pgd_{c,d}tor() can now become static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After the bitmap changes we can get rid of the unlocked versions of
calgary_unmap_sg and iommu_free. Fold __calgary_unmap_sg and
__iommu_free into their calgary_unmap_sg and iommu_free, respectively.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
there function are called via dma_ops->.., so change them to static
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the IOMMU table's lock protects both the bitmap and access
to the hardware's TCE table. Access to the TCE table is synchronized
through the bitmap; therefore, only hold the lock while modifying the
bitmap. This gives a yummy 10-15% reduction in CPU utilization for
netperf on a large SMP machine.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No actual code was harmed in the production of this patch.
Thanks to Andrew Morton <akpm@linux-foundation.org> for telling me
about checkpatch.pl.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cleanup unneeded macros used for register space address calculation.
Now we are using the EBDA to find the space address.
Signed-off-by: Guillaume Thouvenin <guillaume.thouvenin@bull.net>
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This works around a bug where DMAs that have the same addresses as
some MEM regions do not go through. Not clear yet if this is due to a
mis-configuration or something deeper.
[akpm@linux-foundation.org: coding style fixlet]
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide seperate versions for Calgary and CalIOC2
Also print out the PCIe Root Complex Status on CalIOC2 errors
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CalIOC2 is a PCI-e implementation of the Calgary logic. Most of the
programming details are the same, but some differ, e.g., TCE cache
flush. This patch introduces CalIOC2 support - detection and various
support routines. It's not expected to work yet (but will with
follow-on patches).
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... in preparation for doing it differently for CalIOC2.
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Calgary and CalIOC2 share most of the same logic. Introduce struct
cal_chipset_ops for quirks and tce flush logic which are
[akpm@linux-foundation.org: make calgary_chip_ops static]
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... will be used by CalIOC2 later
Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Rise CPUs were only very short-lived, and there are no reports of
anyone both owning one and running Linux on it.
Googling for the printk string "CPU: Rise iDragon" didn't find any dmesg
available online.
If it turns out that against all expectations there are actually users
reverting this patch would be easy.
This patch will make the kernel images smaller by a few bytes for all
i386 users.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On x86_64 kernel, level triggered irq migration gets initiated in the
context of that interrupt(after executing the irq handler) and following
steps are followed to do the irq migration.
1. mask IOAPIC RTE entry; // write to IOAPIC RTE
2. EOI; // processor EOI write
3. reprogram IOAPIC RTE entry // write to IOAPIC RTE with new destination and
// and interrupt vector due to per cpu vector
// allocation.
4. unmask IOAPIC RTE entry; // write to IOAPIC RTE
Because of the per cpu vector allocation in x86_64 kernels, when the irq
migrates to a different cpu, new vector(corresponding to the new cpu) will
get allocated.
An EOI write to local APIC has a side effect of generating an EOI write for
level trigger interrupts (normally this is a broadcast to all IOAPICs).
The EOI broadcast generated as a side effect of EOI write to processor may
be delayed while the other IOAPIC writes (step 3 and 4) can go through.
Normally, the EOI generated by local APIC for level trigger interrupt
contains vector number. The IOAPIC will take this vector number and search
the IOAPIC RTE entries for an entry with matching vector number and clear
the remote IRR bit (indicate EOI). However, if the vector number is
changed (as in step 3) the IOAPIC will not find the RTE entry when the EOI
is received later. This will cause the remote IRR to get stuck causing the
interrupt hang (no more interrupt from this RTE).
Current x86_64 kernel assumes that remote IRR bit is cleared by the time
IOAPIC RTE is reprogrammed. Fix this assumption by checking for remote IRR
bit and if it still set, delay the irq migration to the next interrupt
arrival event(hopefully, next time remote IRR bit will get cleared before
the IOAPIC RTE is reprogrammed).
Initial analysis and patch from Nanhai.
Clean up patch from Suresh.
Rewritten to be less intrusive, and to contain a big fat comment by Eric.
[akpm@linux-foundation.org: fix comments]
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Nanhai Zou <nanhai.zou@intel.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Asit Mallick <asit.k.mallick@intel.com>
Cc: Keith Packard <keith.packard@intel.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This helps to reduce the frequency at which the CPU must be taken out of a
lower-power state.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: Tim Hockin <thockin@hockin.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch (as921) adds code to the show_regs() routine in i386 and x86_64
to print the contents of the debug registers along with all the others.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Following section mismatch warnings were reported by Andrey Borzenkov:
WARNING: arch/i386/kernel/built-in.o - Section mismatch: reference to .init.text:amd_init_mtrr from .text between 'mtrr_bp_init' (at offset 0x967a) and 'mtrr_attrib_to_str'
WARNING: arch/i386/kernel/built-in.o - Section mismatch: reference to .init.text:cyrix_init_mtrr from .text between 'mtrr_bp_init' (at offset 0x967f) and 'mtrr_attrib_to_str'
WARNING: arch/i386/kernel/built-in.o - Section mismatch: reference to .init.text:centaur_init_mtrr from .text between 'mtrr_bp_init' (at offset 0x9684) and 'mtrr_attrib_to_str'
WARNING: arch/i386/kernel/built-in.o - Section mismatch: reference to .init.text: from .text between 'get_mtrr_state' (at offset 0xa735) and 'generic_get_mtrr'
WARNING: arch/i386/kernel/built-in.o - Section mismatch: reference to .init.text: from .text between 'get_mtrr_state' (at offset 0xa749) and 'generic_get_mtrr'
WARNING: arch/i386/kernel/built-in.o - Section mismatch: reference to .init.text: from .text between 'get_mtrr_state' (at offset 0xa770) and 'generic_get_mtrr'
It was tracked down to a few functions missing __init tag.
Compile tested only.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Background:
The MCE handler has several paths that it can take, depending on various
conditions of the MCE status and the value of the 'tolerant' knob. The
exact semantics are not well defined and the code is a bit twisty.
Description:
This patch makes the MCE handler's behavior more clear by documenting the
behavior for various 'tolerant' levels. It also fixes or enhances
several small things in the handler. Specifically:
* If RIPV is set it is not safe to restart, so set the 'no way out'
flag rather than the 'kill it' flag.
* Don't panic() on correctable MCEs.
* If the _OVER bit is set *and* the _UC bit is set (meaning possibly
dropped uncorrected errors), set the 'no way out' flag.
* Use EIPV for testing whether an app can be killed (SIGBUS) rather
than RIPV. According to docs, EIPV indicates that the error is
related to the IP, while RIPV simply means the IP is valid to
restart from.
* Don't clear the MCi_STATUS registers until after the panic() path.
This leaves the status bits set after the panic() so clever BIOSes
can find them (and dumb BIOSes can do nothing).
This patch also calls nonseekable_open() in mce_open (as suggested by akpm).
Result:
Tolerant levels behave almost identically to how they always have, but
not it's well defined. There's a slightly higher chance of panic()ing
when multiple errors happen (a good thing, IMHO). If you take an MBE and
panic(), the error status bits are not cleared.
Alternatives:
None.
Testing:
I used software to inject correctable and uncorrectable errors. With
tolerant = 3, the system usually survives. With tolerant = 2, the system
usually panic()s (PCC) but not always. With tolerant = 1, the system
always panic()s. When the system panic()s, the BIOS is able to detect
that the cause of death was an MC4. I was not able to reproduce the
case of a non-PCC error in userspace, with EIPV, with (tolerant < 3).
That will be rare at best.
Signed-off-by: Tim Hockin <thockin@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Background:
/dev/mcelog is typically polled manually. This is less than optimal for
situations where accurate accounting of MCEs is important. Calling
poll() on /dev/mcelog does not work.
Description:
This patch adds support for poll() to /dev/mcelog. This results in
immediate wakeup of user apps whenever the poller finds MCEs. Because
the exception handler can not take any locks, it can not call the wakeup
itself. Instead, it uses a thread_info flag (TIF_MCE_NOTIFY) which is
caught at the next return from interrupt or exit from idle, calling the
mce_user_notify() routine. This patch also disables the "fake panic"
path of the mce_panic(), because it results in printk()s in the exception
handler and crashy systems.
This patch also does some small cleanup for essentially unused variables,
and moves the user notification into the body of the poller, so it is
only called once per poll, rather than once per CPU.
Result:
Applications can now poll() on /dev/mcelog. When an error is logged
(whether through the poller or through an exception) the applications are
woken up promptly. This should not affect any previous behaviors. If no
MCEs are being logged, there is no overhead.
Alternatives:
I considered simply supporting poll() through the poller and not using
TIF_MCE_NOTIFY at all. However, the time between an uncorrectable error
happening and the user application being notified is *the*most* critical
window for us. Many uncorrectable errors can be logged to the network if
given a chance.
I also considered doing the MCE poll directly from the idle notifier, but
decided that was overkill.
Testing:
I used an error-injecting DIMM to create lots of correctable DRAM errors
and verified that my user app is woken up in sync with the polling interval.
I also used the northbridge to inject uncorrectable ECC errors, and
verified (printk() to the rescue) that the notify routine is called and the
user app does wake up. I built with PREEMPT on and off, and verified
that my machine survives MCEs.
[wli@holomorphy.com: build fix]
Signed-off-by: Tim Hockin <thockin@google.com>
Signed-off-by: William Irwin <bill.irwin@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Background:
/dev/mcelog is a clear-on-read interface. It is currently possible for
multiple users to open and read() the device. Users are protected from
each other during any one read, but not across reads.
Description:
This patch adds support for O_EXCL to /dev/mcelog. If a user opens the
device with O_EXCL, no other user may open the device (EBUSY). Likewise,
any user that tries to open the device with O_EXCL while another user has
the device will fail (EBUSY).
Result:
Applications can get exclusive access to /dev/mcelog. Applications that
do not care will be unchanged.
Alternatives:
A simpler choice would be to only allow one open() at all, regardless of
O_EXCL.
Testing:
I wrote an application that opens /dev/mcelog with O_EXCL and observed
that any other app that tried to open /dev/mcelog would fail until the
exclusive app had closed the device.
Caveats:
None.
Signed-off-by: Tim Hockin <thockin@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Insert the unclaimed MMCONFIG resources into the resource tree without the
IORESOURCE_BUSY flag during late initialization. This allows the MMCONFIG
regions to be visible in the iomem resource tree without interfering with
other system resources that were discovered during PCI initialization.
[akpm@linux-foundation.org: nanofixes]
Signed-off-by: Aaron Durbin <adurbin@google.com>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we are in the emulated NUMA case, we need to make sure that all existing
apicid_to_node mappings that point to real node ID's now point to the
equivalent fake node ID's.
If we simply iterate over all apicid_to_node[] members for each node, we risk
remapping an entry if it shares a node ID with a real node. Since apicid's
may not be consecutive, we're forced to create an automatic array of
apicid_to_node mappings and then copy it over once we have finished remapping
fake to real nodes.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For NUMA emulation, our SLIT should represent the true NUMA topology of the
system but our proximity domain to node ID mapping needs to reflect the
emulated state.
When NUMA emulation has successfully setup fake nodes on the system, a new
function, acpi_fake_nodes() is called. This function determines the proximity
domain (_PXM) for each true node found on the system. It then finds which
emulated nodes have been allocated on this true node as determined by its
starting address. The node ID to PXM mapping is changed so that each fake
node ID points to the PXM of the true node that it is located on.
If the machine failed to register a SLIT, then we assume there is no special
requirement for emulated node affinity so we use the default LOCAL_DISTANCE,
which is newly exported to this code, as our measurement if the emulated nodes
appear in the same PXM. Otherwise, we use REMOTE_DISTANCE.
PXM_INVAL and NID_INVAL are also exported to the ACPI header file so that we
can compare node_to_pxm() results in generic code (in this case, the SRAT
code).
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The logic in e820_find_active_regions() for determining the true active
regions for an e820 entry given a range of PFN's is needed for
e820_hole_size() as well.
e820_hole_size() is called from the NUMA emulation code to determine the
reserved area within an address range on a per-node basis. Its logic should
duplicate that of finding active regions in an e820 entry because these are
the only true ranges we may register anyway.
[akpm@linux-foundation.org: cleanup]
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds caching of pgds and puds, pmds, pte. That way we can avoid costly
zeroing and initialization of special mappings in the pgd.
A second quicklist is useful to separate out PGD handling. We can carry the
initialized pgds over to the next process needing them.
Also clean up the pgd_list handling to use regular list macros. There is no
need anymore to avoid the lru field.
Move the add/removal of the pgds to the pgdlist into the constructor /
destructor. That way the implementation is congruent with i386.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Acked-by: William Lee Irwin III <wli@holomorphy.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Every file should include the headers containing the prototypes for its
global functions.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Constrain __supported_pte_mask and NX handling to just the PAE kernel.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hence remove its handling in the opposite case.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
.. and adjust documentation to properly reflect options that are
x86-64 specific.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Consolidate the three 32-bit system call entry points so that they all
treat registers in similar ways.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove unused code and variables and do some codingstyle / whitespace
cleanups while at it.
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
xtime can be initialized including the cmos update from the generic
timekeeping code. Remove the arch specific implementation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the generic cmos update function in kernel/time/ntp.c
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current SMI detection logic in read_hpet_tsc() makes sure,
that when a SMI happens between the read of the HPET counter and
the read of the TSC, this wrong value is used for TSC calibration.
This is not the intention of the function. The comparison must ensure,
that we do _NOT_ use such a value.
Fix the check to use calibration values where delta of the two TSC reads
is smaller than a reasonable threshold.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Intel PerfMon NMI watchdog reserves the first performance counter,
but uses the second one. Make it correctly reserve the second one.
Signed-off-by: Björn Steinbrink <B.Steinbrink@gmx.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is not fully softirq safe anyways.
Can't do a WARN_ON unfortunately because it could trigger in the
panic case.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With that an L3 cache is correctly reported in the cache information in /sys
With fixes from Andreas Herrmann and Dean Gaudet and Joachim Deguara
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This implements new vDSO for x86-64. The concept is similar
to the existing vDSOs on i386 and PPC. x86-64 has had static
vsyscalls before, but these are not flexible enough anymore.
A vDSO is a ELF shared library supplied by the kernel that is mapped into
user address space. The vDSO mapping is randomized for each process
for security reasons.
Doing this was needed for clock_gettime, because clock_gettime
always needs a syscall fallback and having one at a fixed
address would have made buffer overflow exploits too easy to write.
The vdso can be disabled with vdso=0
It currently includes a new gettimeofday implemention and optimized
clock_gettime(). The gettimeofday implementation is slightly faster
than the one in the old vsyscall. clock_gettime is significantly faster
than the syscall for CLOCK_MONOTONIC and CLOCK_REALTIME.
The new calls are generally faster than the old vsyscall.
Advantages over the old x86-64 vsyscalls:
- Extensible
- Randomized
- Cleaner
- Easier to virtualize (the old static address range previously causes
overhead e.g. for Xen because it has to create special page tables for it)
Weak points:
- glibc support still to be written
The VM interface is partly based on Ingo Molnar's i386 version.
Includes compile fix from Joachim Deguara
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The compiler generally generates reasonable inline code for the simple
cases and for the rest it's better for code size for them to be out of line.
Also there they can be potentially optimized more in the future.
In fact they probably should be in a .S file because they're all pure
assembly, but that's for another day.
Also some code style cleanup on them while I was on it (this seems
to be the last untouched really early Linux code)
This saves ~12k text for a defconfig kernel with gcc 4.1.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In acpi_scan_nodes(), we immediately return -1 if acpi_numa <= 0, meaning
we haven't detected any underlying ACPI topology or we have explicitly
disabled its use from the command-line with numa=noacpi.
acpi_table_print_srat_entry() and acpi_table_parse_srat() are only
referenced within drivers/acpi/numa.c, so we can mark them as static and
remove their prototypes from the header file.
Likewise, pxm_to_node_map[] and node_to_pxm_map[] are only used within
drivers/acpi/numa.c, so we mark them as static and remove their externs
from the header file.
The automatic 'result' variable is unused in acpi_numa_init(), so it's
removed.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use LOCAL_DISTANCE and REMOTE_DISTANCE in x86_64 ACPI code
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linux 64bit only uses the IO-APIC ID as an internal cookie. In the future
there could be some cases where the IO-APIC IDs are not unique because
they share an 8 bit space with CPUs and if there are enough CPUs
it is difficult to get them that. But Linux needs the io apic ID
internally for its data structures. Assign unique IO APIC ids on
table parsing.
TBD do for 32bit too
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a bug introduced with the CLFLUSH changes: we must always flush pages
changed in cpa(), not just when they are reverted.
Reenable CLFLUSH usage with that now (it was temporarily disabled
for .22)
Add some BUG_ONs
Contains fixes from Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reading from the signal{1,2} files requires a spu_acquire_saved, so make these
files write-only for contexts created with SPU_CREATE_NOSCHED.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PS3 bootwrapper files use instructions only available on 64-bit CPUs.
Add the code generation directive '.machine "ppc64"' for toolchains
configured for 32-bit CPUs.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a FLASH ROM Storage Driver for the PS3:
- Implemented as a misc character device driver
- Uses a fixed 256 KiB buffer allocated from boot memory as the hypervisor
requires the writing of aligned 256 KiB blocks
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a BD/DVD/CD-ROM Storage Driver for the PS3:
- Implemented as a SCSI device driver
- Uses software scatter-gather with a 64 KiB bounce buffer as the hypervisor
doesn't support scatter-gather
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a Disk Storage Driver for the PS3:
- Implemented as a block device driver with a dynamic major
- Disk names (and partitions) are of the format ps3d%c(%u)
- Uses software scatter-gather with a 64 KiB bounce buffer as the hypervisor
doesn't support scatter-gather
Cc: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
allnoconfig results in this:
CC arch/powerpc/mm/tlb_32.o
In file included from include/asm/tlb.h:60,
from arch/powerpc/mm/tlb_32.c:30:
include/asm-generic/tlb.h: In function 'tlb_flush_mmu':
include/asm-generic/tlb.h:76: error: implicit declaration of function 'release_pages'
include/asm-generic/tlb.h: In function 'tlb_remove_page':
include/asm-generic/tlb.h:105: error: implicit declaration of function 'page_cache_release'
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
WARNING: arch/i386/kernel/built-in.o(.text+0xb6a7): Section mismatch: reference to .init.text:find_num_cache_leaves (between 'init_intel_cacheinfo' and 'cache_shared_cpu_map_setup')
It could be __init_refok, but gcc >= 4.0 anyway inlines it into the
__cpuinit init_intel_cacheinfo(), and IMHO it's too small for "noinline
__init".
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The patch is necessary on one of my boxen, where programming the stop
sequence twice leads to PIT malfunction.
Sigh !
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
i386 and sparc64 have the identical code to update the cmos clock. Move it
into kernel/time/ntp.c as there are other architectures coming along with the
same requirements.
[akpm@linux-foundation.org: build fixes]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: David Miller <davem@davemloft.net>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add some more debug information to the hrtimer and clock events code.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need to make sure, that the clockevent devices are resumed, before
the tick is resumed. The current resume logic does not guarantee this.
Add CLOCK_EVT_MODE_RESUME and call the set mode functions of the clock
event devices before resuming the tick / oneshot functionality.
Fixup the existing users.
Thanks to Nigel Cunningham for tracking down a long standing thinko,
which affected the jinxed VAIO.
[akpm@linux-foundation.org: xen build fix]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix following warning:
WARNING: vmlinux.o(.text+0x35264): Section mismatch: reference to .init.text:__alloc_bootmem (between 'mdesc_bootmem_alloc' and 'mdesc_bootmem_free')
Rename mdesc_mem_ops to *_ops so modpost ignores __init references
and declare mdesc_bootmem_alloc __init since it is only used
during __init context.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following warning:
WARNING: vmlinux.o(.text+0x3cf50): Section mismatch: reference to .init.text:page_in_phys_avail (between 'pci_sun4v_pbm_init' and 'sun4v_pci_init')
pci_sun4v_pbm_init and sun4v_pci_init was only used under __init
context so declare them _init.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing sparc64 mini_rtc driver can handle CMOS based
rtcs trivially with just a few lines of code and the simplifies
things tremendously.
Tested on SB1500.
Signed-off-by: David S. Miller <davem@davemloft.net>
The dev_handle and dev_ino fields don't match up exactly to
the traditional IMAP_IGN and IMAP_INO masks.
So store them away in a table and look them up directly.
Signed-off-by: David S. Miller <davem@davemloft.net>
When booting up a control node it's quite common to
not be able to register several service types.
And likewise on guests at least one or two are going
to not be there.
Signed-off-by: David S. Miller <davem@davemloft.net>
The best scheme to get uniqueness seems to be:
FOO -- If node lacks "id" property
FOO-$(ID) -- If node has "id" but parent lacks "cfg-handle"
FOO-$(ID)-$(CFG_HANDLE) -- If node has both
Signed-off-by: David S. Miller <davem@davemloft.net>
The current scheme works on static interpretation of text names, which
is wrong.
The output-device setting, for example, must be resolved via an alias
or similar to a full path name to the console device.
Paths also contain an optional set of 'options', which starts with a
colon at the end of the path. The option area is used to specify
which of two serial ports ('a' or 'b') the path refers to when a
device node drives multiple ports. 'a' is assumed if the option
specification is missing.
This was caught by the UltraSPARC-T1 simulator. The 'output-device'
property was set to 'ttya' and we didn't pick upon the fact that this
is an OBP alias set to '/virtual-devices/console'. Instead we saw it
as the first serial console device, instead of the hypervisor console.
The infrastructure is now there to take advantage of this to resolve
the console correctly even in multi-head situations in fbcon too.
Thanks to Greg Onufer for the bug report.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-2.6.23' of master.kernel.org:/pub/scm/linux/kernel/git/arnd/cell-2.6: (37 commits)
[CELL] spufs: rework list management and associated locking
[CELL] oprofile: add support to OProfile for profiling CELL BE SPUs
[CELL] oprofile: enable SPU switch notification to detect currently active SPU tasks
[CELL] spu_base: locking cleanup
[CELL] cell: indexing of SPUs based on firmware vicinity properties
[CELL] spufs: integration of SPE affinity with the scheduller
[CELL] cell: add placement computation for scheduling of affinity contexts
[CELL] spufs: extension of spu_create to support affinity definition
[CELL] cell: add hardcoded spu vicinity information for QS20
[CELL] cell: add vicinity information on spus
[CELL] cell: add per BE structure with info about its SPUs
[CELL] spufs: use find_first_bit() instead of sched_find_first_bit()
[CELL] spufs: remove unused file argument from spufs_run_spu()
[CELL] spufs: change decrementer restore timing
[CELL] spufs: dont halt decrementer at restore step 47
[CELL] spufs: limit saving MFC_CNTL bits
[CELL] spufs: fix read and write for decr_status file
[CELL] spufs: fix decr_status meanings
[CELL] spufs: remove needless context save/restore code
[CELL] spufs: fix array size of channel index
...
Currently, Linux doesn't generate correct page tables for ARMv6 and
later cores if the cache policy is different from the default one (it
may lead to strongly ordered or shared device mappings). This patch
disallows cache policies other than writeback and the
CPU_[ID]CACHE_DISABLE options only affect the CP15 system control
register rather than the page tables.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the necessary ifdef's to the proc-v7.S code and
defines the v7wbi_tlb_fns macro in pgtable-nommu.h
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The auxiliary control and the L2 auxiliary control registers are
Cortex-A8 specific. They need to be removed from the generic ARMv7
support code.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These patches add full SSP/MCU support for the HP Jornada 720
machine. Its needed to handle keyboard, touchscreen, battery
and backlight/lcd.
The main driver exports functions and the header file exports
the command values. When talking to the MCU the general procedure
is to start MCU, send command (using ssp_inout(command)), the
proper reply is always TXDUMMY. After receiving TXDUMMY you can
send the value you wish pushed (for example brightness level).
End with ssp_end() so the spinlock gets unlocked.
Drivers using this havent been implemented yet, but will shortly.
Signed-off-by: Kristoffer Ericson <Kristoffer.ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With this patch, Kconfig only selects CPU_HAS_ASID for the MMU
case. It also corrects the typo in the v6wbi_tlb_fns definition in
pgtable-nommu.h.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The __cpu_{clear|copy}_user_page functions are not defined for the
MMU-less case and therefore should not be exported.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If not MMU and not v6K, access to the TLS register has to be
emulated. MMU-less systems do not provide a high page for kuser
helpers.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The background operations of the L2x0 cache controllers are aborted if
another operation is issued on the same or different core. This patch
protects the maintenance operation issuing/polling with a spinlock.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The 'i' and 'zi' targets short-circuit the dependencies for
'install' and 'zinstall' targets; these are useful for
installing the kernel on platforms which have make but no
compiler installed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is to avoid a compiler warning for overriding the built-in "putc"
function.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This sorts out the various lists and related locks in the spu code.
In detail:
- the per-node free_spus and active_list are gone. Instead struct spu
gained an alloc_state member telling whether the spu is free or not
- the per-node spus array is now locked by a per-node mutex, which
takes over from the global spu_lock and the per-node active_mutex
- the spu_alloc* and spu_free function are gone as the state change is
now done inline in the spufs code. This allows some more sharing of
code for the affinity vs normal case and more efficient locking
- some little refactoring in the affinity code for this locking scheme
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
From: Maynard Johnson <mpjohn@us.ibm.com>
This patch updates the existing arch/powerpc/oprofile/op_model_cell.c
to add in the SPU profiling capabilities. In addition, a 'cell' subdirectory
was added to arch/powerpc/oprofile to hold Cell-specific SPU profiling code.
Exports spu_set_profile_private_kref and spu_get_profile_private_kref which
are used by OProfile to store private profile information in spufs data
structures.
Also incorporated several fixes from other patches (rrn). Check pointer
returned from kzalloc. Eliminated unnecessary cast. Better error
handling and cleanup in the related area. 64-bit unsigned long parameter
was being demoted to 32-bit unsigned int and eventually promoted back to
unsigned long.
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Maynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: Bob Nelson <rrnelson@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
From: Maynard Johnson <mpjohn@us.ibm.com>
This patch adds to the capability of spu_switch_event_register so that
the caller is also notified of currently active SPU tasks.
Exports spu_switch_event_register and spu_switch_event_unregister so
that OProfile can get access to the notifications provided.
Signed-off-by: Maynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Bob Nelson <rrnelson@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Sort out the locking mess in spu_base and document the current rules.
As an added benefit spu_alloc* and spu_free don't block anymore.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch links spus according to their physical position using
information provided by the firmware through a special vicinity
device-tree property. This property is present in current version
of Malta firmware.
Example of vicinity properties for a node in Malta:
Node: Vicinity property contains phandles of:
spe@0 [ spe@100000 , mic-tm@50a000 ]
spe@100000 [ spe@0 , spe@200000 ]
spe@200000 [ spe@100000 , spe@300000 ]
spe@300000 [ spe@200000 , bif0@512000 ]
spe@80000 [ spe@180000 , mic-tm@50a000 ]
spe@180000 [ spe@80000 , spe@280000 ]
spe@280000 [ spe@180000 , spe@380000 ]
spe@380000 [ spe@280000 , bif0@512000 ]
Only spe@* have a vicinity property (e.g., bif0@512000 and
mic-tm@50a000 do not have it).
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch makes the scheduller honor affinity information for each
context being scheduled. If the context has no affinity information,
behaviour is unchanged. If there are affinity information, context is
schedulled to be run on the exact spu recommended by the affinity
placement algorithm.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch provides the spu affinity placement logic for the spufs scheduler.
Each time a gang is going to be scheduled, the placement of a reference
context is defined. The placement of all other contexts with affinity from
the gang is defined based on this reference context location and on a
precomputed displacement offset.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch adds support for additional flags at spu_create, which relate
to the establishment of affinity between contexts and contexts to memory.
A fourth, optional, parameter is supported. This parameter represent
a affinity neighbor of the context being created, and is used when defining
SPU-SPU affinity.
Affinity is represented as a doubly linked list of spu_contexts.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch allows the use of spu affinity on QS20, whose
original FW does not provide affinity information.
This is done through two hardcoded arrays, and by reading the reg
property from each spu.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch adds affinity data to each spu instance.
A doubly linked list is created, meant to connect the spus
in the physical order they are placed in the BE. SPUs
near to memory should be marked as having memory affinity.
Adjustments of the fields acording to FW properties is done
in separate patches, one for CPBW, one for Malta (patch for
Malta under testing).
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Addition of a spufs-global "cbe_info" array. Each entry contains information
about one Cell/B.E. node, namelly:
* list of spus (both free and busy spus are in this list);
* list of free spus (replacing the static spu_list from spu_base.c)
* number of spus;
* number of reserved (non scheduleable) spus.
SPE affinity implementation actually requires only access to one spu per
BE node (since it implements its own pointer to walk through the other spus
of the ring) and the number of scheduleable spus (n_spus - non_sched_spus)
However having this more general structure can be useful for other
functionalities, concentrating per-cbe statistics / data.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
spu_sched->bitmap has MAX_PRIO(=140) width in bits.However, since
ff80a77f20, sched_find_first_bit()
only supports 100-bit bitmaps.
Thus, spu_sched->bitmap should be treated by generic find_first_bit().
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
From: Sebastian Siewior <cbe-oss-dev@ml.breakpoint.cc>
The 'file' argument is unused in spufs_run_spu(). This change removes
it.
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
The SPU decrementer should be restored after the LSCSA DMA has
completed.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
No need to halt the SPE decrementer at context restore step 47, it will
be done in step 7.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
At save step 8, the mfc control register in the CSA should be written
_only_ with Sc and Sm bits (at least MFC_CNTL[Dh] should be set to 0)
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
The decr_status in the LSCSA is valid only in the sequence of context
restore. Thus, it's nonsense to read and/or write it through spufs.
This patch changes decr_status node to access MFC_CNTL[Ds] in the CSA.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
The decr_status in the LSCSA is confusedly used as two meanings:
* SPU decrementer was running
* SPU decrementer was wrapped as a result of adjust
and the code to set decr_status is missing.
This patch fixes these problems by using the decr_status argument as a
set of flags. This requires a rebuild of the shipped spu_restore code.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
The following steps are not needed in the SPE context save/restore
paths:
Save Step 12: save_mfc_decr()
save suspend_time to CSA (It will be done by step 14)
save ch 7 (decrementer value will be saved in LSCSA by spe-side step 10)
Restore Step 59: restore_ch_part1()
restore ch 1 (it will be done by spe-side step 15)
This change removes the unnecessary steps.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Based on a fix from Masato Noguchi <Masato.Noguchi@jp.sony.com>.
Remove the (incorrect) array size declarations in the spufs channel
arrays, and use ARRAY_SIZE rather than hardcoded values.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Currently a process is removed from the physical spu when spu_acquire_saved
is saved but never put back. This patch adds a new spu_release_saved
that is to be paired with spu_acquire_saved and put the process back if
it has been in RUNNABLE state before.
Niether Jeremy not be are entirely happy about this exact patch because
it adds another spu_activate call outside of the owner thread, but I
feel this is the best short-term fix we can come up with.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch exports per-context statistics in spufs as long as spu
statistics in sysfs.
It was formed by merging:
"spufs: add spu stats in sysfs" From: Christoph Hellwig
"spufs: add stat file to spufs" From: Christoph Hellwig
"spufs: fix libassist accounting" From: Jeremy Kerr
"spusched: fix spu utilization statistics" From: Luke Browning
And some adjustments by myself, after suggestions on cbe-oss-dev.
Having separate patches was making the review process harder
than it should, as we end up integrating spus and ctx statistics
accounting much more than it was on the first implementation.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
In 6cbf93960e64f313f6e247cbca7afaa50e3ee2c we added a WARN_ON for
calling spu_deactivate on contexts created with the SPU_CREATE_NOSCHED
flag. However, all NOSCHED contexts will need to be deactivated when
the context is destroyed, so this gives a spurious warning when any
NOSCHED context is closed.
This change removes the WARN_ON.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Reading from the signal{1,2} files requires a spu_acquire_saved, so
make these files write-only for contexts created with
SPU_CREATE_NOSCHED.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
The current SPU context saving procedure in SPUFS unexpectedly
restarts MFC when halting decrementer, because MFC_CNTL[Dh] is set
without MFC_CNTL[Sm]. This bug causes, for example, saving broken DMA
queues. Here is a patch to fix the problem.
Signed-off-by: Kazunori Asayama <asayama@sm.sony.co.jp>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
WARNING: arch/powerpc/platforms/cell/spufs/spufs.o(.init.text+0x158): Section
mismatch: reference to .exit.text:.spu_sched_exit (between '.init_module' and
'.spu_sched_init')
was introduced by c99c1994a2
This patch removes the warning.
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch adds support for the setup and decoding of MSIs
on Axon-based Cell systems, using the MSIC mechanism.
This involves setting up an area of BE memory which the Axon
then uses as a FIFO for MSI messages. When one or more MSIs
are decoded by the MSIC we receive an interrupt on the MPIC,
and the MSI messages are written into the FIFO. At the moment
we use a 64KB FIFO, one per MSIC/BE.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch adds support for investigating spus information after a
kernel crash event, through kdump vmcore file.
Implementation is based on xmon code, but the new functionality was
kept independent from xmon.
Signed-off-by: Lucio Jose Herculano Correia <luciojhc@br.ibm.com>
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
The Axon bridge chip used on new Cell/B.E. based blade servers
comes with a DDR2 memory controller that can be used to
attach cheap memory modules, as opposed to the high-speed
XDR memory that is used by the CPU itself.
Since the memory controller does not participate in the
cache coherency protocol, we can not use the memory direcly
for Linux applications, but by providing a block device
it can be used for swap space, temporary file storage and
through the use of the direct_access block device operation
for mapping into user addresses, when it is mounted with
an appropriate file system.
Signed-off-by: Maxim Shchetynin <maxim@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
The platforms missing the "cpus" property in the "be" node are mono-Cell
platforms such as CAB or Getaway.
Therefore it is possible to assume that if there is no "cpus" properties
under the "be" node then we can safely return the "device node" without
more checking. This is a bit hacky but ... it allows it to work on
these platforms.
Signed-off-by: Jean-Christophe DUBOIS <jcd@tribudubois.net>
Acked-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Previous patch changed based on Christian Krafft's comment.
On some legacy SLOF tree the generic code is unable to ioremap some Cell BE
registers. Therefore the "generic" functions are returning a NULL pointer,
triggering a crash on such platforms.
Let's handle this more gracefully.
Signed-off-by: Jean-Christophe DUBOIS <jcd@tribudubois.net>
Acked-by: Christian Kraff <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Previous patch changed based on Christian Krafft's comment.
On some legacy SLOF tree the generic code is unable to ioremap some Cell BE
registers. Therefore the "generic" functions are returning a NULL pointer,
triggering a crash on such platforms.
Let's handle this more gracefully.
Signed-off-by: Jean-Christophe DUBOIS <jcd@tribudubois.net>
Acked-by: Christian Kraff <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch reorganizes the code of the driver into three files.
Two cbe_cpufreq_pmi.c and cbe_cpufreq_pervasive.c care about hardware.
cbe_cpufreq.c contains the logic.
There is no changed behaviour, except that the PMI related function
is now located in a seperate module cbe_cpufreq_pmi. This module
will be required by cbe_cpufreq, if CONFIG_CBE_CPUFREQ_PMI has been set.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Minor issues have been fixed:
* added a missing call to of_node_put()
* signedness of a function parameter
* added some line breaks
* changed global pmi_frequency_limit to a
per node pmi_slow_mode_limit array
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch fixes the initialization of the cbe_cpufreq driver.
The code that initializes the PMI related functions was called per cpu:
* registering cpufreq notifier block
* registering a pmi handler
This ends in a bug that the notifier block gets called in an endless loop.
The initialization code is being put to the
module init code path by this patch. This way it only gets called once.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch fixes the debug code that calculates the transition time when
changing the slow modes on a Cell BE cpu.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
The pmi driver got simplified by removing support for multiple devices.
As there is no more than one pmi device per maschine, there is no need to
specify the device for listening and sending messages.
This way the caller (cbe_cpufreq) doesn't need to scan the device tree.
When registering the handler on a board without a pmi
interface, pmi.c will just return -ENODEV.
The patch that fixed the breakage of cell_defconfig has been
broken out of the earlier version of this patch. So this is
the version that applies cleanly on top of it.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Prevent people from directly including <asm/rwsem.h>.
[IA64] remove time interpolator
[IA64] Convert to generic timekeeping/clocksource
[IA64] refresh some config files for 64K pagesize
[IA64] Delete iosapic_free_rte()
[IA64] fallocate system call
[IA64] Enable percpu vector domain for IA64_DIG
[IA64] Enable percpu vector domain for IA64_GENERIC
[IA64] Support irq migration across domain
[IA64] Add support for vector domain
[IA64] Add mapping table between irq and vector
[IA64] Check if irq is sharable
[IA64] Fix invalid irq vector assumption for iosapic
[IA64] Use dynamic irq for iosapic interrupts
[IA64] Use per iosapic lock for indirect iosapic register access
[IA64] Cleanup lock order in iosapic_register_intr
[IA64] Remove duplicated members in iosapic_rte_info
[IA64] Remove block structure for locking in iosapic.c
This is a merge of Peter Keilty's initial patch (which was
revived by Bob Picco) for this with Hidetoshi Seto's fixes
and scaling improvements.
Acked-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The commit d815461c7a in linus tree
converts the rtc-rs5c372 driver to a "new style" i2c driver.
Like commit c00593f6f8, this patch
register the rtc i2c device for the em7210 board.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. split pxa_cpu_suspend to pxa25x_cpu_suspend and pxa27x_cpu_suspend
and make pxa25x_cpu_pm_enter() and pxa27x_cpu_pm_enter() to invoke
the corresponding _suspend functions, thus remove all those ugly
#ifdef .. #endif out of sleep.S
2. move the declarations of those suspend functions to pm.h
note: this is not a clean enough solution until all the pxa25x and
pxa27x specific part is further removed out of sleep.S, sleep.S is
supposed to contain generic code only
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. introduce a structure pxa_cpu_pm_fns for pxa25x/pxa27x specific
operations as follows:
struct pxa_cpu_pm_fns {
int save_size;
void (*save)(unsigned long *);
void (*restore)(unsigned long *);
int (*valid)(suspend_state_t state);
void (*enter)(suspend_state_t state);
}
2. processor specific registers saving and restoring are performed
by calling the corresponding (*save) and (*restore)
3. pxa_cpu_pm_fns->save_size should be initialized to the required
size for processor specific registers saving, the allocated
memory address will be passed to (*save) and (*restore)
memory allocation happens early in pxa_pm_init(), and save_size
should be assigned prior to this (which is usually true, since
pxa_pm_init() happens in device_initcall()
4. there're some redundancies for those SLEEP_SAVE_XXX and related
macros, will be fixed later, one way possible is for the system
devices to handle the specific registers saving and restoring
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/sfr/ofcons:
Create drivers/of/platform.c
Create linux/of_platorm.h
[SPARC/64] Rename some functions like PowerPC
Begin consolidation of of_device.h
Begin to consolidate of_device.c
Consolidate of_find_node_by routines
Consolidate of_get_next_child
Consolidate of_get_parent
Consolidate of_find_property
Consolidate of_device_is_compatible
Start split out of common open firmware code
Split out common parts of prom.h
* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6: (26 commits)
sh: intc - add support for SH7750 and its variants
sh: Move entry point code to .text.head.
sh: heartbeat: Shut up resource size warning.
sh: update r2d defconfig and fix SH7751R pci compliation
sh: Many symbol exports for nommu allmodconfig.
sh: zero terminate 8250 platform data for r2d board
sh: cpufreq: Fix up the build for SH-2.
sh: Make on-chip DMA channel selection explicit.
sh: Fix up CPU dependencies for on-chip DMAC.
sh: cpufreq: clock framework support.
sh: Support rate rounding for SH7722 FRQCR clocks.
sh: Implement clk_round_rate() in the clock framework.
sh: Fix up PCI section mismatch warnings.
sh: Wire up fallocate() syscall.
sh: intc - add support for 7780
sh: intc - improve group support
sh: Fix up SH-3 and SH-4 driver dependencies.
sh: push-switch: Correct license string.
sh: cpufreq: Fix driver dependencies and flag as broken.
sh: IPR/INTC2 IRQ setup consolidation.
...
* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh64-2.6:
sh64: Flag sh64_get_page() as __init_refok.
sh64: Move entry point code to .text.head.
sh64: Fix up PCI section mismatch warnings.
sh64: Update cayman defconfig.
sh64: Wire up fallocate() syscall.
Update arm to use bitwise types for its VM_FAULT_ constants.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reformat show_cpuinfo() to be consistent with normal coding style
(and rest of this file).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Every file should include the headers containing the prototypes for
its global functions.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
One of the nice ideas behind paravirt is that CONFIG_XEN=y can be included
in a standard configuration and be no worse for native booting than as a
Xen guest. The glibc feature that supports the vDSO "nosegneg" note is
designed specifically to make this easy. You just have to flip one bit at
boot time. This patch makes Xen flip the bit, so a CONFIG_XEN=y kernel on
bare hardware does not make glibc use the less-optimized library builds.
Signed-off-by: Roland McGrath <roland@redhat.com>
Acked-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Fix two year old bug in early bootup asm.
[SPARC64]: Update defconfig.
[SPARC64]: Fix log message type in vio_create_one().
[SPARC64]: Tweak assertions in sun4v_build_virq().
[SPARC64]: Tweak kernel log messages in power_probe().
[SPARC64]: Fix handling of multiple vdc-port nodes.
[SPARC64]: Fix device type matching in VIO's devspec_show().
[SPARC64]: Fix MODULE_DEVICE_TABLE() specification in VDC and VNET.
[SPARC]: Add sys_fallocate() entries.
[SPARC64]: Use orderly_poweroff().
anything that wants working dma-mapping won't work
parport_pc won't work on m68k unless we have ISA
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
i.e. tell modpost that entry point code (that has to be outside
of .init.text for external reasons) is OK to refer to .init.*
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch converts the cpu specific 7750 setup code to use the
new intc controller. Many new vectors are added and multiple
processor variants including 7091, 7750, 7750s, 7750r, 7751 and
7751r should all have the correct vectors hooked up.
IRLM interrupts can be enabled using ipr_irq_enable_irlm() which
now is marked as __init.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The HRM states that is must be done this way ...
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I changed the naming to be more obvious---unfortunately the HRM
doesn't specify these.
Moreover the numbering is changed to be zero indexed as this is more
natural.
Adjust all callers.
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
make ns9xxx_ack_irq_functions static and add one include to get declarations
for ns9xxx_map_io and ns9xxx_init_machine.
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I must have written the patch introducing support for this machine
deep in the night...
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. for common devices across all the pxa variants, the names
are changed to be:
"pxa_device_xxx"
2. for pxa25x or pxa27x specific devices, the names are
changed to be:
"pxa25x_device_xxx", or
"pxa27x_device_xxx"
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I believe that the following patch is necessary to properly configure
GPIO line configuration for IRQ's which are mapped to a GPIO line >= 8
(without this patch the wrong GPIO is configured as an input.)
Signed-off-by: Tim Harvey <tim_harvey@yahoo.com>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
sh64_get_page() wraps in to regular allocators as well as the
bootmem allocator for fetching pages, it carefully checks to
see which one it can use depending on the system state, so
the access is safe.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the AT91RM9200 platform-setup code to use the new atmel_spi
driver (and manually-driven chip-selects), instead of the legacy
AT91-only SPI stack.
The AT91SAM9 processors are already using the atmel_spi driver.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Follow Al Viro's m68k change from l-k:
i.e. tell modpost that entry point code (that has to be outside
of .init.text for external reasons) is OK to refer to .init.*
Shuts up some section mismatch warnings from modpost.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
In order for this driver to be shared across the iop architectures the
iop3xx and iop13xx header files are modified to present a common interface
for the iop_wdt driver.
Details:
* iop13xx supports disabling the timer while iop3xx does not. This requires
a few 'compatibility' definitions in include/asm-arm/hardware/iop3xx.h to
preclude adding #ifdef CONFIG_ARCH_IOP13XX blocks to the driver code.
* The heartbeat interval is derived from the internal bus clock rate, so this
this patch also exports the tick rate to the iop_wdt driver.
Cc: Curt Bruns <curt.e.bruns@intel.com>
Cc: Peter Milne <peter.milne@d-tacq.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the basic support for the em7210 board. It is similar to
the iq31244 board and can be found on Intel "Baxter Creek" ss4000e nas.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch updates the r2d board support in a few ways:
- CPU_SUBTYPE_SH7751R is selected in the defconfig to play well
with the r2d board Kconfig entry. Without this the defconfig
results in no board enabled.
- Enable EARLY_PRINTK.
- Enable SH_STANDARD_BIOS
- this works well for early printk on the r2d board.
- Add "earlyprink=bios" to the cmdline for early serial port
output by default.
- CONFIG_SUBTYPE_SH7751R support is added to the sh-specific
pci makefile.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
allmodconfig generates a lot of interesting code, a lot of the
generated symbols we've never exported before, so this fixes
those up. Verified with both GCC3 and GCC4 toolchains.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
struct plat_serial8250_port should contain a terminating zero entry
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently this has a prompt to allow users to change it. There's
no reason to do this, and it has caused breakage and confusion
in the past, so remove it entirely.
We'll get rid of this when the whole driver is tidied for
the driver model.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We try to fetch the CIF entry pointer from %o4, but that
can get clobbered by the early OBP calls. It is saved
in %l7 already, so actually this "mov %o4, %l7" can just
be completely removed with no other changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This gets the SH cpufreq working again. We follow the changes
in the AVR32 implementation for wrapping in to the clock framework.
CPUs that wish to use this are required to define rate rounding
primitives in order to satisfy clk_round_rate().
This works well enough for the common case, though we should
look at unifying this driver across all of the platforms that
implement clock framework support in one capacity or another.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the round_rate() op is supported, hook it up on SH7722
for the FRQCR (CPU, PCLK, etc.) clocks.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is an optional component of the clock framework. However,
as we're going to be using this in the cpufreq drivers, add
support for it to the framework.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The "id" property in vdc-port nodes are not unique, they
are all zero. Therefore assign ID's using the parent's
"cfg-handle" property which will be unique.
Signed-off-by: David S. Miller <davem@davemloft.net>
with the recent renames, we forgot to update the matches for
devspec. This is required to keep udev working and autoload modules.
Signed-off-by: David S. Miller <davem@davemloft.net>
H. Peter Anvin