Currently suspend time statistics are showed through debugfs.
Remove time statistics in suspend state since the timing may
not be accurate in that state.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case of interface down, radio is turned off but PCIe mastering is
not cleared.
This can cause unexpected PCIe access to the shutdown device.
Fix this by clearing PCIe mastering also in case interface is down
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add a length check in wil_cfg80211_mgmt_tx to detect unsigned integer
overflow.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add a length check in wmi_set_ie to detect unsigned integer
overflow.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When loading FW from file add block size checks to ensure a
corrupted FW file will not cause the driver to write outside
the device memory.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The current length check:
sizeof(cmd) + len > r->entry_size
will allow very large values of len (> U16_MAX - sizeof(cmd))
and can cause a buffer overflow. Fix the check to cover this case.
In addition, ensure the mailbox entry_size is not too small,
since this can also bypass the above check.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
On-going operations were not aborted properly
and required locks were not taken.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
FW capabilities are currently retrieved only during module
initialization, but userspace can replace the firmware while
interface is down, so refresh the FW capabilities when
interface is up (after FW is loaded) to ensure driver
functionality matches the loaded FW.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Upon sending/receiving WMI commands/events, print human readable
names in addition to id for easier debugging.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Allow run-time suspend when interface is down, keep card alive when
interface is up.
If driver is in wmi only or debug_fw mode run-time PM won't suspend.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Handle tdls peer events from the target. TDLS events for the peer
could be discover, teardown, etc. As of now, adding the logic to
handle tdls teardown events alone.
Teardown due to peer traffic indication(PTR) timeout is one such
teardown event from the target.
Tested this change on QCA9888 with 10.4-3.5.1-00018 fw version.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is required to update the teardown state of the peer when
a tdls link with that peer is terminated. This information is
useful for the target to perform some cleanups wrt the tdls peer.
Without proper cleanup, target assumes that the peer is connected and
blocks future connection requests, updating the teardown state of the
peer addresses the problem.
Tested this change on QCA9888 with 10.4-3.5.1-00018 fw version.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 4ca1807815 ("ath10k: disable wake_tx_queue for older devices")
disables the use of the mac80211 TXQs for some devices because of a theoretical
throughput regression. The original regression report[1] was related to
fq_codel qdisc drop performance, which was fixed in commit 9d18562a22
("fq_codel: add batch ability to fq_codel_drop()"). Since then, we have not
seen the TXQ-related regression, so it should be safe to re-enable TXQs.
[1] http://lists.infradead.org/pipermail/ath10k/2016-April/007266.html
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make use of the swap macro and remove unnecessary variable temp.
This makes the code easier to read and maintain.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pull networking fixes from David Miller:
1) The forcedeth conversion from pci_*() DMA interfaces to dma_*() ones
missed one spot. From Zhu Yanjun.
2) Missing CRYPTO_SHA256 Kconfig dep in cfg80211, from Johannes Berg.
3) Fix checksum offloading in thunderx driver, from Sunil Goutham.
4) Add SPDX to vm_sockets_diag.h, from Stephen Hemminger.
5) Fix use after free of packet headers in TIPC, from Jon Maloy.
6) "sizeof(ptr)" vs "sizeof(*ptr)" bug in i40e, from Gustavo A R Silva.
7) Tunneling fixes in mlxsw driver, from Petr Machata.
8) Fix crash in fanout_demux_rollover() of AF_PACKET, from Mike
Maloney.
9) Fix race in AF_PACKET bind() vs. NETDEV_UP notifier, from Eric
Dumazet.
10) Fix regression in sch_sfq.c due to one of the timer_setup()
conversions. From Paolo Abeni.
11) SCTP does list_for_each_entry() using wrong struct member, fix from
Xin Long.
12) Don't use big endian netlink attribute read for
IFLA_BOND_AD_ACTOR_SYSTEM, it is in cpu endianness. Also from Xin
Long.
13) Fix mis-initialization of q->link.clock in CBQ scheduler, preventing
adding filters there. From Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
ethernet: dwmac-stm32: Fix copyright
net: via: via-rhine: use %p to format void * address instead of %x
net: ethernet: xilinx: Mark XILINX_LL_TEMAC broken on 64-bit
myri10ge: Update MAINTAINERS
net: sched: cbq: create block for q->link.block
atm: suni: remove extraneous space to fix indentation
atm: lanai: use %p to format kernel addresses instead of %x
VSOCK: Don't set sk_state to TCP_CLOSE before testing it
atm: fore200e: use %pK to format kernel addresses instead of %x
ambassador: fix incorrect indentation of assignment statement
vxlan: use __be32 type for the param vni in __vxlan_fdb_delete
bonding: use nla_get_u64 to extract the value for IFLA_BOND_AD_ACTOR_SYSTEM
sctp: use right member as the param of list_for_each_entry
sch_sfq: fix null pointer dereference at timer expiration
cls_bpf: don't decrement net's refcount when offload fails
net/packet: fix a race in packet_bind() and packet_notifier()
packet: fix crash in fanout_demux_rollover()
sctp: remove extern from stream sched
sctp: force the params with right types for sctp csum apis
sctp: force SCTP_ERROR_INV_STRM with __u32 when calling sctp_chunk_fail
...
* CRYPTO_SHA256 is needed for regdb validation
* mac80211: mesh path metric was wrong in some frames
* mac80211: use QoS null-data packets on QoS connections
* mac80211: tear down RX aggregation sessions first to
drop fewer packets in HW restart scenarios
-----BEGIN PGP SIGNATURE-----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=ODX1
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2017-11-27' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Four fixes:
* CRYPTO_SHA256 is needed for regdb validation
* mac80211: mesh path metric was wrong in some frames
* mac80211: use QoS null-data packets on QoS connections
* mac80211: tear down RX aggregation sessions first to
drop fewer packets in HW restart scenarios
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When connected to a QoS/WMM AP, mac80211 should use a QoS NDP
for probing it, instead of a regular non-QoS one, fix this.
Change all the drivers to *not* allow QoS NDP for now, even
though it looks like most of them should be OK with that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull timer updates from Thomas Gleixner:
- The final conversion of timer wheel timers to timer_setup().
A few manual conversions and a large coccinelle assisted sweep and
the removal of the old initialization mechanisms and the related
code.
- Remove the now unused VSYSCALL update code
- Fix permissions of /proc/timer_list. I still need to get rid of that
file completely
- Rename a misnomed clocksource function and remove a stale declaration
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
m68k/macboing: Fix missed timer callback assignment
treewide: Remove TIMER_FUNC_TYPE and TIMER_DATA_TYPE casts
timer: Remove redundant __setup_timer*() macros
timer: Pass function down to initialization routines
timer: Remove unused data arguments from macros
timer: Switch callback prototype to take struct timer_list * argument
timer: Pass timer_list pointer to callbacks unconditionally
Coccinelle: Remove setup_timer.cocci
timer: Remove setup_*timer() interface
timer: Remove init_timer() interface
treewide: setup_timer() -> timer_setup() (2 field)
treewide: setup_timer() -> timer_setup()
treewide: init_timer() -> setup_timer()
treewide: Switch DEFINE_TIMER callbacks to struct timer_list *
s390: cmm: Convert timers to use timer_setup()
lightnvm: Convert timers to use timer_setup()
drivers/net: cris: Convert timers to use timer_setup()
drm/vc4: Convert timers to use timer_setup()
block/laptop_mode: Convert timers to use timer_setup()
net/atm/mpc: Avoid open-coded assignment of timer callback function
...
First set of fixes for 4.15. Most important here is the iwlwifi fix
for scan command firmware interface change.
ath10k
* fix CCMP-256, GCMP and GCMP-256 in raw mode, it was never working
wcn36xx
* fix device tree node search
iwlwifi
* fix a regression with firmware API change of scan cmd (introduced in
firmware version 34)
* add a bunch of PCI IDs and fix configuration structs for A000 devices
* fix the exported firmware name strings for 9000 and A000 devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaFZQwAAoJEG4XJFUm622bOe8H/0dmodmL+nf0MUKYyXmV2l5J
3wN0Xrse1NL3bRDTGZ/KkX/OFB1FSZ8ViGW0ek9DvbbF4lC9E5WqjM5HbTY7QE6i
bBgF476qnV9Hy/ay9SEMe7HhxsU8KfVKuYgNzY8pHhlCLkr96h35YNt+LtD319zT
PTBrxURLkZotr44mDQjO8duyKZFCafWN6F5nd22+JWpOEQDK4rUNNdDT/16CwQiy
aLqCF5bHB4kOigd9YfEpx1jO6GusqGqkB0x3lwG0QR7oygFgLZbWre0TllE+ly8P
x7gy40euxBWh9Hlk+4xjxBfZraE41XzXTTHyJECVRLKJcrlEvzCc+QCOyoYjZpY=
=uYE+
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2017-11-22' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.15
First set of fixes for 4.15. Most important here is the iwlwifi fix
for scan command firmware interface change.
ath10k
* fix CCMP-256, GCMP and GCMP-256 in raw mode, it was never working
wcn36xx
* fix device tree node search
iwlwifi
* fix a regression with firmware API change of scan cmd (introduced in
firmware version 34)
* add a bunch of PCI IDs and fix configuration structs for A000 devices
* fix the exported firmware name strings for 9000 and A000 devices
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With all callbacks converted, and the timer callback prototype
switched over, the TIMER_FUNC_TYPE cast is no longer needed,
so remove it. Conversion was done with the following scripts:
perl -pi -e 's|\(TIMER_FUNC_TYPE\)||g' \
$(git grep TIMER_FUNC_TYPE | cut -d: -f1 | sort -u)
perl -pi -e 's|\(TIMER_DATA_TYPE\)||g' \
$(git grep TIMER_DATA_TYPE | cut -d: -f1 | sort -u)
The now unused macros are also dropped from include/linux/timer.h.
Signed-off-by: Kees Cook <keescook@chromium.org>
This mechanically converts all remaining cases of ancient open-coded timer
setup with the old setup_timer() API, which is the first step in timer
conversions. This has no behavioral changes, since it ultimately just
changes the order of assignment to fields of struct timer_list when
finding variations of:
init_timer(&t);
f.function = timer_callback;
t.data = timer_callback_arg;
to be converted into:
setup_timer(&t, timer_callback, timer_callback_arg);
The conversion is done with the following Coccinelle script, which
is an improved version of scripts/cocci/api/setup_timer.cocci, in the
following ways:
- assignments-before-init_timer() cases
- limit the .data case removal to the specific struct timer_list instance
- handling calls by dereference (timer->field vs timer.field)
spatch --very-quiet --all-includes --include-headers \
-I ./arch/x86/include -I ./arch/x86/include/generated \
-I ./include -I ./arch/x86/include/uapi \
-I ./arch/x86/include/generated/uapi -I ./include/uapi \
-I ./include/generated/uapi --include ./include/linux/kconfig.h \
--dir . \
--cocci-file ~/src/data/setup_timer.cocci
@fix_address_of@
expression e;
@@
init_timer(
-&(e)
+&e
, ...)
// Match the common cases first to avoid Coccinelle parsing loops with
// "... when" clauses.
@match_immediate_function_data_after_init_timer@
expression e, func, da;
@@
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
(
-\(e.function\|e->function\) = func;
-\(e.data\|e->data\) = da;
|
-\(e.data\|e->data\) = da;
-\(e.function\|e->function\) = func;
)
@match_immediate_function_data_before_init_timer@
expression e, func, da;
@@
(
-\(e.function\|e->function\) = func;
-\(e.data\|e->data\) = da;
|
-\(e.data\|e->data\) = da;
-\(e.function\|e->function\) = func;
)
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
@match_function_and_data_after_init_timer@
expression e, e2, e3, e4, e5, func, da;
@@
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
... when != func = e2
when != da = e3
(
-e.function = func;
... when != da = e4
-e.data = da;
|
-e->function = func;
... when != da = e4
-e->data = da;
|
-e.data = da;
... when != func = e5
-e.function = func;
|
-e->data = da;
... when != func = e5
-e->function = func;
)
@match_function_and_data_before_init_timer@
expression e, e2, e3, e4, e5, func, da;
@@
(
-e.function = func;
... when != da = e4
-e.data = da;
|
-e->function = func;
... when != da = e4
-e->data = da;
|
-e.data = da;
... when != func = e5
-e.function = func;
|
-e->data = da;
... when != func = e5
-e->function = func;
)
... when != func = e2
when != da = e3
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
@r1 exists@
expression t;
identifier f;
position p;
@@
f(...) { ... when any
init_timer@p(\(&t\|t\))
... when any
}
@r2 exists@
expression r1.t;
identifier g != r1.f;
expression e8;
@@
g(...) { ... when any
\(t.data\|t->data\) = e8
... when any
}
// It is dangerous to use setup_timer if data field is initialized
// in another function.
@script:python depends on r2@
p << r1.p;
@@
cocci.include_match(False)
@r3@
expression r1.t, func, e7;
position r1.p;
@@
(
-init_timer@p(&t);
+setup_timer(&t, func, 0UL);
... when != func = e7
-t.function = func;
|
-t.function = func;
... when != func = e7
-init_timer@p(&t);
+setup_timer(&t, func, 0UL);
|
-init_timer@p(t);
+setup_timer(t, func, 0UL);
... when != func = e7
-t->function = func;
|
-t->function = func;
... when != func = e7
-init_timer@p(t);
+setup_timer(t, func, 0UL);
)
Signed-off-by: Kees Cook <keescook@chromium.org>
This changes all DEFINE_TIMER() callbacks to use a struct timer_list
pointer instead of unsigned long. Since the data argument has already been
removed, none of these callbacks are using their argument currently, so
this renames the argument to "unused".
Done using the following semantic patch:
@match_define_timer@
declarer name DEFINE_TIMER;
identifier _timer, _callback;
@@
DEFINE_TIMER(_timer, _callback);
@change_callback depends on match_define_timer@
identifier match_define_timer._callback;
type _origtype;
identifier _origarg;
@@
void
-_callback(_origtype _origarg)
+_callback(struct timer_list *unused)
{ ... }
Signed-off-by: Kees Cook <keescook@chromium.org>
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
To make things worse, the parent mmio node was also prematurely freed.
Fixes: fd52bdae9a ("wcn36xx: Disable 5GHz for wcn3620")
Cc: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make sure 16-byte mic is removed from the rx data packet
tail when CCMP-256, GCMP and GCMP-256 ciphers are used
in raw decap mode. This fixed rx traffic failures in those
ciphers in raw mode. Split the helper returning crypto
tail length into two, one to get the ICV length and other
to get the mic lengh for the cipher to make it clean.
Fixes: 2ea9f12cef ("ath10k: add new cipher suite support")
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
hwsim_new_radio_nl() now copies the name attribute in order to add a
null-terminator. mac80211_hwsim_new_radio() (indirectly) copies it
again into the net_device structure, so the first copy is not used or
freed later. Free the first copy before returning.
Fixes: ff4dd73dd2 ("mac80211_hwsim: check HWSIM_ATTR_RADIO_NAME length")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* Support new FW API version of scan cmd (used in FW version 34);
* Add a bunch of PCI IDs and fix configuration structs for A000
devices;
* Fix the exported firmware name strings for 9000 and A000 devices;
-----BEGIN PGP SIGNATURE-----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=JPn9
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-for-kalle-2017-11-19' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
iwlwifi: first set of fixes for 4.15
* Support new FW API version of scan cmd (used in FW version 34);
* Add a bunch of PCI IDs and fix configuration structs for A000
devices;
* Fix the exported firmware name strings for 9000 and A000 devices;
In the cases where len is too long, the error return path fails to
kfree allocated buffers buf and usb_reg_buf. The simplest fix is to
perform the sanity check on len before the allocations to avoid having
to do the kfree'ing in the first place.
Detected by CoverityScan, CID#1452258,1452259 ("Resource Leak")
Fixes: 59f73e2ae1 ("rsi: check length before USB read/write register")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iwlwifi 9000 and a0000 series hw contains an extra dash in firmware
file name as seeen in modinfo output for kernel 4.14:
firmware: iwlwifi-9260-th-b0-jf-b0--34.ucode
firmware: iwlwifi-9260-th-a0-jf-a0--34.ucode
firmware: iwlwifi-9000-pu-a0-jf-b0--34.ucode
firmware: iwlwifi-9000-pu-a0-jf-a0--34.ucode
firmware: iwlwifi-QuQnj-a0-hr-a0--34.ucode
firmware: iwlwifi-QuQnj-a0-jf-b0--34.ucode
firmware: iwlwifi-QuQnj-f0-hr-a0--34.ucode
firmware: iwlwifi-Qu-a0-jf-b0--34.ucode
firmware: iwlwifi-Qu-a0-hr-a0--34.ucode
Fix that by dropping the extra adding of '"-"'.
Signed-off-by: Thomas Backlund <tmb@mageia.org>
Cc: stable@vger.kernel.org # 4.13
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A lot of PCI IDs were missing and there were some problems with the
configuration and firmware selection for devices on the 9000 series.
Fix the firmware selection by adding files for the B-steps; add
configuration for some integrated devices; and add a bunch of PCI IDs
(mostly for integrated devices) that were missing from the driver's
list.
Without this patch, a lot of devices will not be recognized or will
try to load the wrong firmware file.
Cc: stable@vger.kernel.org # 4.13
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
According to the description, first argument of genlmsg_nlhdr() points to
what genlmsg_put() returns, i.e. beginning of user header. Therefore we
should only subtract size of genetlink header and netlink message header,
not user header.
This also means we don't need to pass the pointer to genetlink family and
the same is true for genl_dump_check_consistent() which is the only caller
of genlmsg_nlhdr(). (Note that at the moment, these functions are only
used for families which do not have user header so that they are not
affected.)
Fixes: 670dc2833d ("netlink: advertise incomplete dumps")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Highlights:
1) Maintain the TCP retransmit queue using an rbtree, with 1GB
windows at 100Gb this really has become necessary. From Eric
Dumazet.
2) Multi-program support for cgroup+bpf, from Alexei Starovoitov.
3) Perform broadcast flooding in hardware in mv88e6xxx, from Andrew
Lunn.
4) Add meter action support to openvswitch, from Andy Zhou.
5) Add a data meta pointer for BPF accessible packets, from Daniel
Borkmann.
6) Namespace-ify almost all TCP sysctl knobs, from Eric Dumazet.
7) Turn on Broadcom Tags in b53 driver, from Florian Fainelli.
8) More work to move the RTNL mutex down, from Florian Westphal.
9) Add 'bpftool' utility, to help with bpf program introspection.
From Jakub Kicinski.
10) Add new 'cpumap' type for XDP_REDIRECT action, from Jesper
Dangaard Brouer.
11) Support 'blocks' of transformations in the packet scheduler which
can span multiple network devices, from Jiri Pirko.
12) TC flower offload support in cxgb4, from Kumar Sanghvi.
13) Priority based stream scheduler for SCTP, from Marcelo Ricardo
Leitner.
14) Thunderbolt networking driver, from Amir Levy and Mika Westerberg.
15) Add RED qdisc offloadability, and use it in mlxsw driver. From
Nogah Frankel.
16) eBPF based device controller for cgroup v2, from Roman Gushchin.
17) Add some fundamental tracepoints for TCP, from Song Liu.
18) Remove garbage collection from ipv6 route layer, this is a
significant accomplishment. From Wei Wang.
19) Add multicast route offload support to mlxsw, from Yotam Gigi"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2177 commits)
tcp: highest_sack fix
geneve: fix fill_info when link down
bpf: fix lockdep splat
net: cdc_ncm: GetNtbFormat endian fix
openvswitch: meter: fix NULL pointer dereference in ovs_meter_cmd_reply_start
netem: remove unnecessary 64 bit modulus
netem: use 64 bit divide by rate
tcp: Namespace-ify sysctl_tcp_default_congestion_control
net: Protect iterations over net::fib_notifier_ops in fib_seq_sum()
ipv6: set all.accept_dad to 0 by default
uapi: fix linux/tls.h userspace compilation error
usbnet: ipheth: prevent TX queue timeouts when device not ready
vhost_net: conditionally enable tx polling
uapi: fix linux/rxrpc.h userspace compilation errors
net: stmmac: fix LPI transitioning for dwmac4
atm: horizon: Fix irq release error
net-sysfs: trigger netlink notification on ifalias change via sysfs
openvswitch: Using kfree_rcu() to simplify the code
openvswitch: Make local function ovs_nsh_key_attr_size() static
openvswitch: Fix return value check in ovs_meter_cmd_features()
...
Newer firmware versions (such as iwlwifi-8000C-34.ucode) have
introduced an API change in the SCAN_REQ_UMAC command that is not
backwards compatible. The driver needs to detect and use the new API
format when the firmware reports it, otherwise the scan command will
not work properly, causing a command timeout.
Fix this by adding a TLV that tells the driver that the new API is in
use and use the correct structures for it.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=197591
Fixes: d7a5b3e9e4 ("iwlwifi: mvm: bump API to 34 for 8000 and up")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
The firmware for brcmfmac devices includes information regarding
regulatory constraints. For certain devices this information is kept
separately in a binary form that needs to be downloaded to the device.
This patch adds support to download this so-called CLM blob file. It
uses the same naming scheme as the other firmware files with extension
of .clm_blob.
The CLM blob file is optional. If the file does not exist, the download
process will be bypassed. It will not affect the driver loading.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
"INVALID_STATE" is already being returned in the default case and this
code cannot be reached.
Addresses-Coverity-ID: 1398384
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rt2x00 uses the deprecated do_gettimeofday() function to get a timestamp
for its debugfs "dump" file interface.
The timestamp is using an unsigned 32-bit value, so we could make it
work until 2106 by using ktime_get_real_ts64(), but it seems better to
use monotonic times, as we normally want for timestamps.
Since this is an interface change, I'm incrementing the
DUMP_HEADER_VERSION number, so user space can figure out whether the
timestamps are monotonic or not. Most likely the tools won't care either
way.
Generally speaking, ABI version numbers and in particular changing them
is a bad idea. However since this is in debugfs, we don't put any
API stability rules on the interface according to
Documentation/filesystems/debugfs.txt, and we can take the easy way
out here; anyone using the frame dump feature can probably work out
the differences here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ENOENT usb error mean "specified interface or endpoint does not exist or
is not enabled". Mark device not present when we encounter this error
similar like we do with ENODEV error.
Otherwise we can have infinite loop in rt2x00usb_work_rxdone(), because
we remove and put again RX entries to the queue infinitely.
We can have similar situation when submit urb will fail all the time
with other error, so we need consider to limit number of entries
processed by rxdone work. But for now, since the patch fixes
reproducible soft lockup issue on single processor systems
and taken ENOENT error meaning, let apply this fix.
Patch adds additional ENOENT check not only in rx kick routine, but
also on other places where we check for ENODEV error.
Reported-by: Richard Genoud <richard.genoud@gmail.com>
Debugged-by: Richard Genoud <richard.genoud@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Specifically, following parameters are needed for wireless device
configuration but were not available to it before:
- HT/VHT capabilities and capabilities masks.
- full channel info (not just IEEE number)
- BSSID hint
- previous BSSID for reassoc request
Move Management Frame Protection setting from common encr info
structure into STA-specific .connect command parameters.
Make sure that all new qlink structure definitions are alignment-safe.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Include HT/VHT caps directly into command so that they won't have
to be searched for in IEs.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Current logic artificially divides "start AP" procedure into three
stages:
- generic interface configuration (security, channel etc)
- IE's processing
- enable AP mode on interface
This separation would not allow to do a proper device configuration as
first stage needs to use information from IEs that are processed on
a second stage. Which means first and second stages have to be meged.
In that case there is no point anymore to keep third stage either, so
merge all three into a single command.
This new command carries all the same info as contained in
"struct cfg80211_ap_settings".
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Data contained within "Append IEs" command (QLINK_CMD_MGMT_SET_APPIE)
duplicates QTN_TLV_ID_IE_SET TLV. Convert the command to use that TLV
instead.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
"IE set" TLV carries the same information as
qlink_event_scan_result::frame_type. Convert the event to make use of
TLV and drop frame_type member.
While at it, make qlink_event_scan_result structure alignement-safe.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Specifying frame type for "IE set" TLV will allow to use several
TLVs in a single message.
Modify users accordingly.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Supported WiFi operation modes are now identified per-band based on
HT/VHT capabilities of each band.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Information on which HT/VHT capabilities can be overridden is reported
per-MAC by wireless device.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HT/VHT capabilities must be reported per each band supported by a radio,
not for all bands on a radio. Furthermore, driver better not assume
any capabilities and just use whetever is reported by device itself.
To support this, convert "get channels" command into "get band info"
command. Difference is that it may also carry HT/VHT capabilities along
with channels information.
While at it, also add "num_bitrates" field to "get band info" command,
for future use.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The configuration of the IEs for probe requests was done in a P2P
related function, which is not very obvious. Moving it to
.scan callback function, ie. brcmf_cfg80211_scan().
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Lazar Alexei