When a new link instance is created, it is trigged to start by
sending it a TIPC_STARTING_EVT, whereafter a regular link
reset is applied to it.
The starting event is codewise treated as a timeout event, and prompts
a link RESET message to be sent to the peer node, carrying a link
session identifier. The later link_reset() call nudges this session
identifier, whereafter all subsequent RESET messages will be sent out
with the new identifier. The latter session number overrides the former,
causing the peer to unconditionally accept it irrespective of its
current working state.
We don't think that this causes any problem, but it is not in accordance
with the protocol spec, and may cause confusion when debugging TIPC
sessions.
To avoid this, we make the starting event distinct from the
subsequent timeout events, by not allowing the former to send
out any RESET message. This eliminates the described problem.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instances of struct node are created in the function tipc_disc_rcv()
under the assumption that there is no race between received discovery
messages arriving from the same node. This assumption is wrong.
When we use more than one bearer, it is possible that discovery
messages from the same node arrive at the same moment, resulting in
creation of two instances of struct tipc_node. This may later cause
confusion during link establishment, and may result in one of the links
never becoming activated.
We fix this by making lookup and potential creation of nodes atomic.
Instead of first looking up the node, and in case of failure, create it,
we now start with looking up the node inside node_link_create(), and
return a reference to that one if found. Otherwise, we go ahead and
create the node as we did before.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During link failover it may happen that the remaining link goes
down while it is still in the process of taking over traffic
from a previously failed link. When this happens, we currently
abort the failover procedure and reset the first failed link to
non-failover mode, so that it will be ready to re-establish
contact with its peer when it comes available.
However, if the first link goes down because its bearer was manually
disabled, it is not enough to reset it; it must also be deleted;
which is supposed to happen when the failover procedure is finished.
Otherwise it will remain a zombie link: attached to the owner node
structure, in mode LINK_STOPPED, and permanently blocking any re-
establishing of the link to the peer via the interface in question.
We fix this by amending the failover abort procedure. Apart from
resetting the link to non-failover state, we test if the link is
also in LINK_STOPPED mode. If so, we delete it, using the conditional
tipc_link_delete() function introduced in the previous commit.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a bearer is disabled, all pertaining links will be reset and
deleted. However, if there is a second active link towards a killed
link's destination, the delete has to be postponed until the failover
is finished. During this interval, we currently put the link in zombie
mode, i.e., we take it out of traffic, delete its timer, but leave it
attached to the owner node structure until all missing packets have
been received. When this is done, we detach the link from its node
and delete it, assuming that the synchronous timer deletion that was
initiated earlier in a different thread has finished.
This is unsafe, as the failover may finish before del_timer_sync()
has returned in the other thread.
We fix this by adding an atomic reference counter of type kref in
struct tipc_link. The counter keeps track of the references kept
to the link by the owner node and the timer. We then do a conditional
delete, based on the reference counter, both after the failover has
been finished and when the timer expires, if applicable. Whoever
comes last, will actually delete the link. This approach also implies
that we can make the deletion of the timer asynchronous.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Max unacked packets/bytes is an int while sizeof(long) was used in the
sysctl table.
This means that when they were getting read we'd also leak kernel memory
to userspace along with the timeout values.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* revert a patch that caused a regression with mesh userspace (Bob)
* fix a number of suspend/resume related races
(from Emmanuel, Luca and myself - we'll look at backporting later)
* add software implementations for new ciphers (Jouni)
* add a new ACPI ID for Broadcom's rfkill (Mika)
* allow using netns FD for wireless (Vadim)
* some other cleanups (various)
-----BEGIN PGP SIGNATURE-----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=wOaR
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-02-03' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Last round of updates for net-next:
* revert a patch that caused a regression with mesh userspace (Bob)
* fix a number of suspend/resume related races
(from Emmanuel, Luca and myself - we'll look at backporting later)
* add software implementations for new ciphers (Jouni)
* add a new ACPI ID for Broadcom's rfkill (Mika)
* allow using netns FD for wireless (Vadim)
* some other cleanups (various)
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-02-03
Here's what's likely the last bluetooth-next pull request for 3.20.
Notable changes include:
- xHCI workaround + a new id for the ath3k driver
- Several new ids for the btusb driver
- Support for new Intel Bluetooth controllers
- Minor cleanups to ieee802154 code
- Nested sleep warning fix in socket accept() code path
- Fixes for Out of Band pairing handling
- Support for LE scan restarting for HCI_QUIRK_STRICT_DUPLICATE_FILTER
- Improvements to data we expose through debugfs
- Proper handling of Hardware Error HCI events
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds skb_remcsum_process and skb_gro_remcsum_process to
perform the appropriate adjustments to the skb when receiving
remote checksum offload.
Updated vxlan and gue to use these functions.
Tested: Ran TCP_RR and TCP_STREAM netperf for VXLAN and GUE, did
not see any change in performance.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When 'learned_sync' flag is turned on, the offloaded switch
port syncs learned MAC addresses to bridge's FDB via switchdev notifier
(NETDEV_SWITCH_FDB_ADD). Currently, FDB entries learnt via this mechanism are
wrongly being deleted by bridge aging logic. This patch ensures that FDB
entries synced from offloaded switch ports are not deleted by bridging logic.
Such entries can only be deleted via switchdev notifier
(NETDEV_SWITCH_FDB_DEL).
Signed-off-by: Siva Mannem <siva.mannem.lnx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A typical qdisc setup is the following :
bond0 : bonding device, using HTB hierarchy
eth1/eth2 : slaves, multiqueue NIC, using MQ + FQ qdisc
XPS allows to spread packets on specific tx queues, based on the cpu
doing the send.
Problem is that dequeues from bond0 qdisc can happen on random cpus,
due to the fact that qdisc_run() can dequeue a batch of packets.
CPUA -> queue packet P1 on bond0 qdisc, P1->ooo_okay=1
CPUA -> queue packet P2 on bond0 qdisc, P2->ooo_okay=0
CPUB -> dequeue packet P1 from bond0
enqueue packet on eth1/eth2
CPUC -> dequeue packet P2 from bond0
enqueue packet on eth1/eth2 using sk cache (ooo_okay is 0)
get_xps_queue() then might select wrong queue for P1, since current cpu
might be different than CPUA.
P2 might be sent on the old queue (stored in sk->sk_tx_queue_mapping),
if CPUC runs a bit faster (or CPUB spins a bit on qdisc lock)
Effect of this bug is TCP reorders, and more generally not optimal
TX queue placement. (A victim bulk flow can be migrated to the wrong TX
queue for a while)
To fix this, we have to record sender cpu number the first time
dev_queue_xmit() is called for one tx skb.
We can union napi_id (used on receive path) and sender_cpu,
granted we clear sender_cpu in skb_scrub_packet() (credit to Willem for
this union idea)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFCEE_DISCOVER_CMD is a specified NCI command used to discover
NFCEE IDs.
Move nci_nfcee_discover() call to nci_discover_se() in order to
guarantee:
- NFCEE_DISCOVER_CMD run when the NCI state machine is initialized
- NFCEE_DISCOVER_CMD is not run in case there is not discover_se
hook defined by a NFC device driver.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
conn_info is currently allocated only after nfcee_discovery_ntf
which is not generic enough for logical connection other than
NFCEE. The corresponding conn_info is now created in
nci_core_conn_create_rsp().
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
For consistency sake change nci_core_conn_create_rsp structure
credits field to credits_cnt.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The current implementation limits nci_core_conn_create_req()
to only manage NCI_DESTINATION_NFCEE.
Add new parameters to nci_core_conn_create() to support all
destination types described in the NCI specification.
Because there are some parameters with variable size dynamic
buffer allocation is needed.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The NCI_STATIC_RF_CONN_ID logical connection is the most used
connection. Keeping it directly accessible in the nci_dev
structure will simplify and optimize the access.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If the IPv6 fragment id has not been set and we perform
fragmentation due to UFO, select a new fragment id.
We now consider a fragment id of 0 as unset and if id selection
process returns 0 (after all the pertrubations), we set it to
0x80000000, thus giving us ample space not to create collisions
with the next packet we may have to fragment.
When doing UFO integrity checking, we also select the
fragment id if it has not be set yet. This is stored into
the skb_shinfo() thus allowing UFO to function correclty.
This patch also removes duplicate fragment id generation code
and moves ipv6_select_ident() into the header as it may be
used during GSO.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This one needs to copy the same data from user potentially more than
once. Sadly, MTU changes can trigger that ;-/
Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
That takes care of the majority of ->sendmsg() instances - most of them
via memcpy_to_msg() or assorted getfrag() callbacks. One place where we
still keep memcpy_fromiovecend() is tipc - there we potentially read the
same data over and over; separate patch, that...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
patch is actually smaller than it seems to be - most of it is unindenting
the inner loop body in tcp_sendmsg() itself...
the bit in tcp_input.c is going to get reverted very soon - that's what
memcpy_from_msg() will become, but not in this commit; let's keep it
reasonably contained...
There's one potentially subtle change here: in case of short copy from
userland, mainline tcp_send_syn_data() discards the skb it has allocated
and falls back to normal path, where we'll send as much as possible after
rereading the same data again. This patch trims SYN+data skb instead -
that way we don't need to copy from the same place twice.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Use iov_iter_kvec() there, get rid of set_fs() games - now that
rxrpc_send_data() uses iov_iter primitives, it'll handle ITER_KVEC just
fine.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Convert skb_add_data() to iov_iter; allows to get rid of the explicit
messing with iovec in its only caller - skb_add_data() will keep advancing
->msg_iter for us, so there's no need to similate that manually.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
As it is, zero msg_iovlen means that the first iovec in the kernel
array of iovecs is left uninitialized, so checking if its ->iov_base
is NULL is random. Since the real users of that thing are doing
sendto(fd, NULL, 0, ...), they are getting msg_iovlen = 1 and
msg_iov[0] = {NULL, 0}, which is what this test is trying to catch.
As suggested by davem, let's just check that msg_iovlen was 1 and
msg_iov[0].iov_base was NULL - _that_ is well-defined and it catches
what we want to catch.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The functions "cipso_v4_doi_putdef" and "kfree" could be called in some cases
by the netlbl_mgmt_add_common() function during error handling even if the
passed variables contained still a null pointer.
* This implementation detail could be improved by adjustments for jump labels.
* Let us return immediately after the first failed function call according to
the current Linux coding style convention.
* Let us delete also an unnecessary check for the variable "entry" there.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cipso_v4_doi_free() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cipso_v4_doi_putdef() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix an Oopsable condition when nsm_mon_unmon is called as part of the
namespace cleanup, which now apparently happens after the utsname
has been freed.
Link: http://lkml.kernel.org/r/20150125220604.090121ae@neptune.home
Reported-by: Bruno Prémont <bonbons@linux-vserver.org>
Cc: stable@vger.kernel.org # 3.18
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
* flexfiles: (53 commits)
pnfs: lookup new lseg at lseg boundary
nfs41: .init_read and .init_write can be called with valid pg_lseg
pnfs: Update documentation on the Layout Drivers
pnfs/flexfiles: Add the FlexFile Layout Driver
nfs: count DIO good bytes correctly with mirroring
nfs41: wait for LAYOUTRETURN before retrying LAYOUTGET
nfs: add a helper to set NFS_ODIRECT_RESCHED_WRITES to direct writes
nfs41: add NFS_LAYOUT_RETRY_LAYOUTGET to layout header flags
nfs/flexfiles: send layoutreturn before freeing lseg
nfs41: introduce NFS_LAYOUT_RETURN_BEFORE_CLOSE
nfs41: allow async version layoutreturn
nfs41: add range to layoutreturn args
pnfs: allow LD to ask to resend read through pnfs
nfs: add nfs_pgio_current_mirror helper
nfs: only reset desc->pg_mirror_idx when mirroring is supported
nfs41: add a debug warning if we destroy an unempty layout
pnfs: fail comparison when bucket verifier not set
nfs: mirroring support for direct io
nfs: add mirroring support to pgio layer
pnfs: pass ds_commit_idx through the commit path
...
Conflicts:
fs/nfs/pnfs.c
fs/nfs/pnfs.h
Add a call to tally stats for a task under a different statsidx than
what's contained in the task structure.
This is needed to properly account for pnfs reads/writes when the
DS nfs version != the MDS version.
Signed-off-by: Weston Andros Adamson <dros@primarydata.com>
Signed-off-by: Tom Haynes <Thomas.Haynes@primarydata.com>
These patches improve the scalability of the NFSoRDMA client and take large
variables off of the stack. Additionally, the GFP_* flags are updated to
match what TCP uses.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=YCZe
-----END PGP SIGNATURE-----
Merge tag 'nfs-rdma-for-3.20' of git://git.linux-nfs.org/projects/anna/nfs-rdma
NFS: Client side changes for RDMA
These patches improve the scalability of the NFSoRDMA client and take large
variables off of the stack. Additionally, the GFP_* flags are updated to
match what TCP uses.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
* tag 'nfs-rdma-for-3.20' of git://git.linux-nfs.org/projects/anna/nfs-rdma: (21 commits)
xprtrdma: Update the GFP flags used in xprt_rdma_allocate()
xprtrdma: Clean up after adding regbuf management
xprtrdma: Allocate zero pad separately from rpcrdma_buffer
xprtrdma: Allocate RPC/RDMA receive buffer separately from struct rpcrdma_rep
xprtrdma: Allocate RPC/RDMA send buffer separately from struct rpcrdma_req
xprtrdma: Allocate RPC send buffer separately from struct rpcrdma_req
xprtrdma: Add struct rpcrdma_regbuf and helpers
xprtrdma: Refactor rpcrdma_buffer_create() and rpcrdma_buffer_destroy()
xprtrdma: Simplify synopsis of rpcrdma_buffer_create()
xprtrdma: Take struct ib_qp_attr and ib_qp_init_attr off the stack
xprtrdma: Take struct ib_device_attr off the stack
xprtrdma: Free the pd if ib_query_qp() fails
xprtrdma: Remove rpcrdma_ep::rep_func and ::rep_xprt
xprtrdma: Move credit update to RPC reply handler
xprtrdma: Remove rl_mr field, and the mr_chunk union
xprtrdma: Remove rpcrdma_ep::rep_ia
xprtrdma: Rename "xprt" and "rdma_connect" fields in struct rpcrdma_xprt
xprtrdma: Clean up hdrlen
xprtrdma: Display XIDs in host byte order
xprtrdma: Modernize htonl and ntohl
...
This is yet another Broadcom bluetooth chip with ACPI ID BCM2E40.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The bnep_get_device function may be triggered by an ioctl just after a
connection has gone down. In such a case the respective L2CAP chan->conn
pointer will get set to NULL (by l2cap_chan_del). This patch adds a
missing NULL check for this case in the bnep_get_device() function.
Reported-by: Patrik Flykt <patrik.flykt@linux.intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree,
they are:
1) Validate hooks for nf_tables NAT expressions, otherwise users can
crash the kernel when using them from the wrong hook. We already
got one user trapped on this when configuring masquerading.
2) Fix a BUG splat in nf_tables with CONFIG_DEBUG_PREEMPT=y. Reported
by Andreas Schultz.
3) Avoid unnecessary reroute of traffic in the local input path
in IPVS that triggers a crash in in xfrm. Reported by Florian
Wiessner and fixes by Julian Anastasov.
4) Fix memory and module refcount leak from the error path of
nf_tables_newchain().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-By: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currntly, if we are not doing UFO on the packet, all UDP
packets will start with CHECKSUM_NONE and thus perform full
checksum computations in software even if device support
IPv6 checksum offloading.
Let's start start with CHECKSUM_PARTIAL if the device
supports it and we are sending only a single packet at
or below mtu size.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds the same functionaliy to IPv6 that
commit 903ab86d19
Author: Herbert Xu <herbert@gondor.apana.org.au>
Date: Tue Mar 1 02:36:48 2011 +0000
udp: Add lockless transmit path
added to IPv4.
UDP transmit path can now run without a socket lock,
thus allowing multiple threads to send to a single socket
more efficiently.
This is only used when corking/MSG_MORE is not used.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we can individually construct IPv6 skbs to send, add a
udpv6_send_skb() function to populate the udp header and send the
skb. This allows udp_v6_push_pending_frames() to re-use this
function as well as enables us to add lockless sendmsg() support.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit is very similar to
commit 1c32c5ad6f
Author: Herbert Xu <herbert@gondor.apana.org.au>
Date: Tue Mar 1 02:36:47 2011 +0000
inet: Add ip_make_skb and ip_finish_skb
It adds IPv6 version of the helpers ip6_make_skb and ip6_finish_skb.
The job of ip6_make_skb is to collect messages into an ipv6 packet
and poplulate ipv6 eader. The job of ip6_finish_skb is to transmit
the generated skb. Together they replicated the job of
ip6_push_pending_frames() while also provide the capability to be
called independently. This will be needed to add lockless UDP sendmsg
support.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to append data to arbitrary queue. This
will be needed later to implement lockless UDP sends.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull IPv6 cork initialization into its own function that
can be re-used. IPv6 specific cork data did not have an
explicit data structure. This patch creats eone so that
just ipv6 cork data can be as arguemts. Also, since
IPv6 tries to save the flow label into inet_cork_full
tructure, pass the full cork.
Adjust ip6_cork_release() to take cork data structures.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One deployment requirement of DCTCP is to be able to run
in a DC setting along with TCP traffic. As Glenn Judd's
NSDI'15 paper "Attaining the Promise and Avoiding the Pitfalls
of TCP in the Datacenter" [1] (tba) explains, one way to
solve this on switch side is to split DCTCP and TCP traffic
in two queues per switch port based on the DSCP: one queue
soley intended for DCTCP traffic and one for non-DCTCP traffic.
For the DCTCP queue, there's the marking threshold K as
explained in commit e3118e8359 ("net: tcp: add DCTCP congestion
control algorithm") for RED marking ECT(0) packets with CE.
For the non-DCTCP queue, there's f.e. a classic tail drop queue.
As already explained in e3118e8359, running DCTCP at scale
when not marking SYN/SYN-ACK packets with ECT(0) has severe
consequences as for non-ECT(0) packets, traversing the RED
marking DCTCP queue will result in a severe reduction of
connection probability.
This is due to the DCTCP queue being dominated by ECT(0) traffic
and switches handle non-ECT traffic in the RED marking queue
after passing K as drops, where K is usually a low watermark
in order to leave enough tailroom for bursts. Splitting DCTCP
traffic among several queues (ECN and non-ECN queue) is being
considered a terrible idea in the network community as it
splits single flows across multiple network paths.
Therefore, commit e3118e8359 implements this on Linux as
ECT(0) marked traffic, as we argue that marking all packets
of a DCTCP flow is the only viable solution and also doesn't
speak against the draft.
However, recently, a DCTCP implementation for FreeBSD hit also
their mainline kernel [2]. In order to let them play well
together with Linux' DCTCP, we would need to loosen the
requirement that ECT(0) has to be asserted during the 3WHS as
not implemented in FreeBSD. This simplifies the ECN test and
lets DCTCP work together with FreeBSD.
Joint work with Daniel Borkmann.
[1] https://www.usenix.org/conference/nsdi15/technical-sessions/presentation/judd
[2] 8ad8794452
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Glenn Judd <glenn.judd@morganstanley.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tx timestamps are looped onto the error queue on top of an skb. This
mechanism leaks packet headers to processes unless the no-payload
options SOF_TIMESTAMPING_OPT_TSONLY is set.
Add a sysctl that optionally drops looped timestamp with data. This
only affects processes without CAP_NET_RAW.
The policy is checked when timestamps are generated in the stack.
It is possible for timestamps with data to be reported after the
sysctl is set, if these were queued internally earlier.
No vulnerability is immediately known that exploits knowledge
gleaned from packet headers, but it may still be preferable to allow
administrators to lock down this path at the cost of possible
breakage of legacy applications.
Signed-off-by: Willem de Bruijn <willemb@google.com>
----
Changes
(v1 -> v2)
- test socket CAP_NET_RAW instead of capable(CAP_NET_RAW)
(rfc -> v1)
- document the sysctl in Documentation/sysctl/net.txt
- fix access control race: read .._OPT_TSONLY only once,
use same value for permission check and skb generation.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add timestamping option SOF_TIMESTAMPING_OPT_TSONLY. For transmit
timestamps, this loops timestamps on top of empty packets.
Doing so reduces the pressure on SO_RCVBUF. Payload inspection and
cmsg reception (aside from timestamps) are no longer possible. This
works together with a follow on patch that allows administrators to
only allow tx timestamping if it does not loop payload or metadata.
Signed-off-by: Willem de Bruijn <willemb@google.com>
----
Changes (rfc -> v1)
- add documentation
- remove unnecessary skb->len test (thanks to Richard Cochran)
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving an interface activation notification, if
the RF interface is NCI_RF_INTERFACE_NFCEE_DIRECT, we
need to ignore the following parameters and change the NCI
state machine to NCI_LISTEN_ACTIVE. According to the NCI
specification, the parameters should be 0 and shall be
ignored.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The NFCC sends an NCI_OP_RF_NFCEE_ACTION_NTF notification
to the host (DH) to let it know that for example an RF
transaction with a payment reader is done.
For now the notification handler is empty.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFC_EVT_TRANSACTION is sent through netlink in order for a
specific application running on a secure element to notify
userspace of an event. Typically the secure element application
counterpart on the host could interpret that event and act
upon it.
Forwarded information contains:
- SE host generating the event
- Application IDentifier doing the operation
- Applications parameters
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
According to the NCI specification, one can use HCI over NCI
to talk with specific NFCEE. The HCI network is viewed as one
logical NFCEE.
This is needed to support secure element running HCI only
firmwares embedded on an NCI capable chipset, like e.g. the
st21nfcb.
There is some duplication between this piece of code and the
HCI core code, but the latter would need to be abstracted even
more to be able to use NCI as a logical transport for HCP packets.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to communicate with an NFCEE, we need to open a logical
connection to it, by sending the NCI_OP_CORE_CONN_CREATE_CMD
command to the NFCC. It's left up to the drivers to decide when
to close an already opened logical connection.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFCEEs can be enabled or disabled by sending the
NCI_OP_NFCEE_MODE_SET_CMD command to the NFCC. This patch
provides an API for drivers to enable and disable e.g. their
NCI discoveredd secure elements.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
NFCEEs (NFC Execution Environment) have to be explicitly
discovered by sending the NCI_OP_NFCEE_DISCOVER_CMD
command. The NFCC will respond to this command by telling
us how many NFCEEs are connected to it. Then the NFCC sends
a notification command for each and every NFCEE connected.
Here we implement support for sending
NCI_OP_NFCEE_DISCOVER_CMD command, receiving the response
and the potential notifications.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The current NCI core only support the RF static connection.
For other NFC features such as Secure Element communication, we
may need to create logical connections to the NFCEE (Execution
Environment.
In order to track each logical connection ID dynamically, we add a
linked list of connection info pointers to the nci_dev structure.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This extended return parameters struct conflicts with the new Read Local
OOB Extended Data command definition. To avoid the conflict simply
rename the old "extended" version to the normal one and update the code
appropriately to take into account the two possible response PDU sizes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When using LE_SCAN_FILTER_DUP_ENABLE, some controllers would send
advertising report from each LE device only once. That means that we
don't get any updates on RSSI value, and makes Service Discovery very
slow. This patch adds restarting scan when in Service Discovery, and
device with filtered uuid is found, but it's not in RSSI range to send
event yet. This way if device moves into range, we will quickly get RSSI
update.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently there is no way to restart le scan, and it's needed in
service scan method. The way it work: it disable, and then enable le
scan on controller.
During the restart, we must remember when the scan was started, and
it's duration, to later re-schedule the le_scan_disable work, that was
stopped during the stop scan phase.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support to set/del bridge port attributes in hardware from
the bridge driver.
With this, when the user sends a bridge setlink message with no flags or
master flags set,
- the bridge driver ndo_bridge_setlink handler sets settings in the kernel
- calls the swicthdev api to propagate the attrs to the switchdev
hardware
You can still use the self flag to go to the switch hw or switch port
driver directly.
With this, it also makes sure a notification goes out only after the
attributes are set both in the kernel and hw.
The patch calls switchdev api only if BRIDGE_FLAGS_SELF is not set.
This is because the offload cases with BRIDGE_FLAGS_SELF are handled in
the caller (in rtnetlink.c).
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds two new api's netdev_switch_port_bridge_setlink
and netdev_switch_port_bridge_dellink to offload bridge port attributes
to switch port
(The names of the apis look odd with 'switch_port_bridge',
but am more inclined to change the prefix of the api to something else.
Will take any suggestions).
The api's look at the NETIF_F_HW_SWITCH_OFFLOAD feature flag to
pass bridge port attributes to the port device.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bridge flags are needed inside ndo_bridge_setlink/dellink handlers to
avoid another call to parse IFLA_AF_SPEC inside these handlers
This is used later in this series
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit be9f4a44e7 ("ipv4: tcp: remove per net tcp_sock")
I tried to address contention on a socket lock, but the solution
I chose was horrible :
commit 3a7c384ffd ("ipv4: tcp: unicast_sock should not land outside
of TCP stack") addressed a selinux regression.
commit 0980e56e50 ("ipv4: tcp: set unicast_sock uc_ttl to -1")
took care of another regression.
commit b5ec8eeac4 ("ipv4: fix ip_send_skb()") fixed another regression.
commit 811230cd85 ("tcp: ipv4: initialize unicast_sock sk_pacing_rate")
was another shot in the dark.
Really, just use a proper socket per cpu, and remove the skb_orphan()
call, to re-enable flow control.
This solves a serious problem with FQ packet scheduler when used in
hostile environments, as we do not want to allocate a flow structure
for every RST packet sent in response to a spoofed packet.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using Secure Connections Only mode, then only P-256 OOB data is
valid and should be provided. In case userspace provides P-192 and P-256
OOB data, then the P-192 values will be set to zero. However the present
value of the IO capability exchange still mentioned that both values
would be available. Fix this by telling the controller clearly that only
the P-256 OOB data is present.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For debugging purposes it is good to know which OOB data is actually
currently loaded for each controller. So expose that list via debugfs.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the Hardware Error event is send by the controller, the Bluetooth
core stores the error code. Expose it via debugfs so it can be retrieved
later on.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To allow easier debugging when debug keys are generated, provide debugfs
entry for checking the setting of debug keys usage.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the HCI Write Simple Pairing Debug Mode command has been issued,
the result needs to be tracked and stored. The hdev->ssp_debug_mode
variable is already present, but was never updated when the mode in
the controller was actually changed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The value of the ssp_debug_mode should be accessible via debugfs to be
able to determine if a BR/EDR controller generates debugs keys or not.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Get rid of nr_cpu_ids and use modern percpu allocation.
Note that the sockets themselves are not yet allocated
using NUMA affinity.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current behavior only passes RTTs from sequentially acked data to CC.
If sender gets a combined ACK for segment 1 and SACK for segment 3, then the
computed RTT for CC is the time between sending segment 1 and receiving SACK
for segment 3.
Pass the minimum computed RTT from any acked data to CC, i.e. time between
sending segment 3 and receiving SACK for segment 3.
Signed-off-by: Kenneth Klette Jonassen <kennetkl@ifi.uio.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the remote only provided P-192 or P-256 data for OOB pairing,
then make sure that the data value pointers are correctly set. That way
the core can provide correct information when remote OOB data present
information have to be communicated.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Before setting the OOB data present flag with SMP pairing, check the
newly introduced present tracking that actual OOB data values have
been provided. The existence of remote OOB data structure does not
actually mean that the correct data values are available.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When BR/EDR Secure Connections has been enabled, the OOB data present
value can take 2 additional values. The host has to clearly provide
details about if P-192 OOB data, P-256 OOB data or a combination of
P-192 and P-256 OOB data is present.
In case BR/EDR Secure Connections is not enabled or not supported,
then check that P-192 OOB data is actually present and return the
correct value based on that.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Instead of doing complex calculation every time the OOB data is used,
just calculate the OOB data present value and store it with the OOB
data raw values.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 constructs by msecs_to_jiffies(var).
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
vlan_get_protocol() could not get network protocol if a skb has a 802.1ad
vlan tag or multiple vlans, which caused incorrect checksum calculation
in several drivers.
Fix vlan_get_protocol() to retrieve network protocol instead of incorrect
vlan protocol.
As the logic is the same as skb_network_protocol(), create a common helper
function __vlan_get_protocol() and call it from existing functions.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
They are all either written once or extremly rarely (e.g. from init
code), so we can move them to the .data..read_mostly section.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When making use of RFC5061, section 4.2.4. for setting the primary IP
address, we're passing a wrong parameter header to param_type2af(),
resulting always in NULL being returned.
At this point, param.p points to a sctp_addip_param struct, containing
a sctp_paramhdr (type = 0xc004, length = var), and crr_id as a correlation
id. Followed by that, as also presented in RFC5061 section 4.2.4., comes
the actual sctp_addr_param, which also contains a sctp_paramhdr, but
this time with the correct type SCTP_PARAM_IPV{4,6}_ADDRESS that
param_type2af() can make use of. Since we already hold a pointer to
addr_param from previous line, just reuse it for param_type2af().
Fixes: d6de309759 ("[SCTP]: Add the handling of "Set Primary IP Address" parameter to INIT")
Signed-off-by: Saran Maruti Ramanara <saran.neti@telus.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The subscription bitmask passed via struct sockaddr_nl is converted to
the group number when calling the netlink_bind() and netlink_unbind()
callbacks.
The conversion is however incorrect since bitmask (1 << 0) needs to be
mapped to group number 1. Note that you cannot specify the group number 0
(usually known as _NONE) from setsockopt() using NETLINK_ADD_MEMBERSHIP
since this is rejected through -EINVAL.
This problem became noticeable since 97840cb ("netfilter: nfnetlink:
fix insufficient validation in nfnetlink_bind") when binding to bitmask
(1 << 0) in ctnetlink.
Reported-by: Andre Tomt <andre@tomt.net>
Reported-by: Ivan Delalande <colona@arista.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reflect the more conservative approach used in the socket transport's
version of this transport method. An RPC buffer allocation should
avoid forcing not just FS activity, but any I/O.
In particular, two recent changes missed updating xprtrdma:
- Commit c6c8fe79a8 ("net, sunrpc: suppress allocation warning ...")
- Commit a564b8f039 ("nfs: enable swap on NFS")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
rpcrdma_{de}register_internal() are used only in verbs.c now.
MAX_RPCRDMAHDR is no longer used and can be removed.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Use the new rpcrdma_alloc_regbuf() API to shrink the amount of
contiguous memory needed for a buffer pool by moving the zero
pad buffer into a regbuf.
This is for consistency with the other uses of internally
registered memory.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
The rr_base field is currently the buffer where RPC replies land.
An RPC/RDMA reply header lands in this buffer. In some cases an RPC
reply header also lands in this buffer, just after the RPC/RDMA
header.
The inline threshold is an agreed-on size limit for RDMA SEND
operations that pass from server and client. The sum of the
RPC/RDMA reply header size and the RPC reply header size must be
less than this threshold.
The largest RDMA RECV that the client should have to handle is the
size of the inline threshold. The receive buffer should thus be the
size of the inline threshold, and not related to RPCRDMA_MAX_SEGS.
RPC replies received via RDMA WRITE (long replies) are caught in
rq_rcv_buf, which is the second half of the RPC send buffer. Ie,
such replies are not involved in any way with rr_base.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
The rl_base field is currently the buffer where each RPC/RDMA call
header is built.
The inline threshold is an agreed-on size limit to for RDMA SEND
operations that pass between client and server. The sum of the
RPC/RDMA header size and the RPC header size must be less than or
equal to this threshold.
Increasing the r/wsize maximum will require MAX_SEGS to grow
significantly, but the inline threshold size won't change (both
sides agree on it). The server's inline threshold doesn't change.
Since an RPC/RDMA header can never be larger than the inline
threshold, make all RPC/RDMA header buffers the size of the
inline threshold.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Because internal memory registration is an expensive and synchronous
operation, xprtrdma pre-registers send and receive buffers at mount
time, and then re-uses them for each RPC.
A "hardway" allocation is a memory allocation and registration that
replaces a send buffer during the processing of an RPC. Hardway must
be done if the RPC send buffer is too small to accommodate an RPC's
call and reply headers.
For xprtrdma, each RPC send buffer is currently part of struct
rpcrdma_req so that xprt_rdma_free(), which is passed nothing but
the address of an RPC send buffer, can find its matching struct
rpcrdma_req and rpcrdma_rep quickly via container_of / offsetof.
That means that hardway currently has to replace a whole rpcrmda_req
when it replaces an RPC send buffer. This is often a fairly hefty
chunk of contiguous memory due to the size of the rl_segments array
and the fact that both the send and receive buffers are part of
struct rpcrdma_req.
Some obscure re-use of fields in rpcrdma_req is done so that
xprt_rdma_free() can detect replaced rpcrdma_req structs, and
restore the original.
This commit breaks apart the RPC send buffer and struct rpcrdma_req
so that increasing the size of the rl_segments array does not change
the alignment of each RPC send buffer. (Increasing rl_segments is
needed to bump up the maximum r/wsize for NFS/RDMA).
This change opens up some interesting possibilities for improving
the design of xprt_rdma_allocate().
xprt_rdma_allocate() is now the one place where RPC send buffers
are allocated or re-allocated, and they are now always left in place
by xprt_rdma_free().
A large re-allocation that includes both the rl_segments array and
the RPC send buffer is no longer needed. Send buffer re-allocation
becomes quite rare. Good send buffer alignment is guaranteed no
matter what the size of the rl_segments array is.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
There are several spots that allocate a buffer via kmalloc (usually
contiguously with another data structure) and then register that
buffer internally. I'd like to split the buffers out of these data
structures to allow the data structures to scale.
Start by adding functions that can kmalloc and register a buffer,
and can manage/preserve the buffer's associated ib_sge and ib_mr
fields.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Move the details of how to create and destroy rpcrdma_req and
rpcrdma_rep structures into helper functions.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: There is one call site for rpcrdma_buffer_create(). All of
the arguments there are fields of an rpcrdma_xprt.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Reduce stack footprint of the connection upcall handler function.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Device attributes are large, and are used in more than one place.
Stash a copy in dynamically allocated memory.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
If ib_query_qp() fails or the memory registration mode isn't
supported, don't leak the PD. An orphaned IB/core resource will
cause IB module removal to hang.
Fixes: bd7ed1d133 ("RPC/RDMA: check selected memory registration ...")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: The rep_func field always refers to rpcrdma_conn_func().
rep_func should have been removed by commit b45ccfd25d ("xprtrdma:
Remove MEMWINDOWS registration modes").
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Reduce work in the receive CQ handler, which can be run at hardware
interrupt level, by moving the RPC/RDMA credit update logic to the
RPC reply handler.
This has some additional benefits: More header sanity checking is
done before trusting the incoming credit value, and the receive CQ
handler no longer touches the RPC/RDMA header (the CPU stalls while
waiting for the header contents to be brought into the cache).
This further extends work begun by commit e7ce710a88 ("xprtrdma:
Avoid deadlock when credit window is reset").
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: Since commit 0ac531c183 ("xprtrdma: Remove REGISTER
memory registration mode"), the rl_mr pointer is no longer used
anywhere.
After removal, there's only a single member of the mr_chunk union,
so mr_chunk can be removed as well, in favor of a single pointer
field.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: This field is not used.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: Use consistent field names in struct rpcrdma_xprt.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: Replace naked integers with a documenting macro.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
xprtsock.c and the backchannel code display XIDs in host byte order.
Follow suit in xprtrdma.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Clean up: Replace htonl and ntohl with the be32 equivalents.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Make it easier to grep the system log for specific error conditions.
The wc.opcode field is not included because opcode numbers are
sparse, and because wc.opcode is not necessarily valid when
completion reports an error.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
commit f5a41847ac ("ipvs: move ip_route_me_harder for ICMP")
from 2.6.37 introduced ip_route_me_harder() call for responses to
local clients, so that we can provide valid rt_src after SNAT.
It was used by TCP to provide valid daddr for ip_send_reply().
After commit 0a5ebb8000 ("ipv4: Pass explicit daddr arg to
ip_send_reply()." from 3.0 this rerouting is not needed anymore
and should be avoided, especially in LOCAL_IN.
Fixes 3.12.33 crash in xfrm reported by Florian Wiessner:
"3.12.33 - BUG xfrm_selector_match+0x25/0x2f6"
Reported-by: Smart Weblications GmbH - Florian Wiessner <f.wiessner@smart-weblications.de>
Tested-by: Smart Weblications GmbH - Florian Wiessner <f.wiessner@smart-weblications.de>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
RFC 1191 said, "a host MUST not increase its estimate of the Path
MTU in response to the contents of a Datagram Too Big message."
Signed-off-by: Li Wei <lw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When many pf_packet listeners are created on a lot of interfaces the
current implementation using global packet type lists scales poorly.
This patch adds per net_device packet type lists to fix this problem.
The patch was originally written by Eric Biederman for linux-2.6.29.
Tested on linux-3.16.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Salam Noureddine <noureddine@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IFLA_LINK_NETNSID is used, the netdevice should be built in this link netns
and moved at the end to another netns (pointed by the socket netns or
IFLA_NET_NS_[PID|FD]).
Existing user of the newlink handler will use the netns argument (src_net) to
find a link netdevice or to check some other information into the link netns.
For example, to find a netdevice, two information are required: an ifindex
(usually from IFLA_LINK) and a netns (this link netns).
Note: when using IFLA_LINK_NETNSID and IFLA_NET_NS_[PID|FD], a user may create a
netdevice that stands in netnsX and with its link part in netnsY, by sending a
rtnl message from netnsZ.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
src_net points to the netns where the netlink message has been received. This
netns may be different from the netns where the interface is created (because
the user may add IFLA_NET_NS_[PID|FD]). In this case, src_net is the link netns.
It seems wrong to override the netns in the newlink() handler because if it
was not already src_net, it means that the user explicitly asks to create the
netdevice in another netns.
CC: Sjur Brændeland <sjur.brandeland@stericsson.com>
CC: Dmitry Tarnyagin <dmitry.tarnyagin@lockless.no>
Fixes: 8391c4aab1 ("caif: Bugfixes in CAIF netdevice for close and flow control")
Fixes: c412540063 ("caif-hsi: Add rtnl support")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I added sk_pacing_rate field, I forgot to initialize its value
in the per cpu unicast_sock used in ip_send_unicast_reply()
This means that for sch_fq users, RST packets, or ACK packets sent
on behalf of TIME_WAIT sockets might be sent to slowly or even dropped
once we reach the per flow limit.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 95bd09eb27 ("tcp: TSO packets automatic sizing")
Signed-off-by: David S. Miller <davem@davemloft.net>
TIME_WAIT sockets are not owning any skb.
ip_send_unicast_reply() and tcp_v6_send_response() both use
regular sockets.
We can safely remove a test in sch_fq and save one cache line miss,
as sk_state is far away from sk_pacing_rate.
Tested at Google for about one year.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NET_ACT_CONNMARK fails to build if NF_CONNTRACK_MARK is disabled,
and d7924450e1 ("act_connmark: Add missing dependency on
NF_CONNTRACK_MARK") fixed that case, but missed the cased where
NF_CONNTRACK is a loadable module.
This adds the second dependency to ensure that NET_ACT_CONNMARK
can only be built-in if NF_CONNTRACK is also part of the kernel
rather than a loadable module.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sock_iocb structure is allocate on stack for each read/write-like
operation on sockets, and contains various fields of which only the
embedded msghdr and sometimes a pointer to the scm_cookie is ever used.
Get rid of the sock_iocb and put a msghdr directly on the stack and pass
the scm_cookie explicitly to netlink_mmap_sendmsg.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, it isn't possible to request checksums on the outer UDP
header of tunnels - the TUNNEL_CSUM flag is ignored. This adds
support for requesting that UDP checksums be computed on transmit
and properly reported if they are present on receive.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the first NFC pull request for 3.20.
With this one we have:
- Secure element support for the ST Micro st21nfca driver. This depends
on a few HCI internal changes in order for example to support more
than one secure element per controller.
- ACPI support for NXP's pn544 HCI driver. This controller is found on
many x86 SoCs and is typically enumerated on the ACPI bus there.
- A few st21nfca and st21nfcb fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SNWp
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-3.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
NFC: 3.20 first pull request
This is the first NFC pull request for 3.20.
With this one we have:
- Secure element support for the ST Micro st21nfca driver. This depends
on a few HCI internal changes in order for example to support more
than one secure element per controller.
- ACPI support for NXP's pn544 HCI driver. This controller is found on
many x86 SoCs and is typically enumerated on the ACPI bus there.
- A few st21nfca and st21nfcb fixes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported in: https://bugzilla.kernel.org/show_bug.cgi?id=92081
This patch avoids calling rtnl_notify if the device ndo_bridge_getlink
handler does not return any bytes in the skb.
Alternately, the skb->len check can be moved inside rtnl_notify.
For the bridge vlan case described in 92081, there is also a fix needed
in bridge driver to generate a proper notification. Will fix that in
subsequent patch.
v2: rebase patch on net tree
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug in CUBIC that causes cwnd to increase slightly
too slowly when multiple ACKs arrive in the same jiffy.
If cwnd is supposed to increase at a rate of more than once per jiffy,
then CUBIC was sometimes too slow. Because the bic_target is
calculated for a future point in time, calculated with time in
jiffies, the cwnd can increase over the course of the jiffy while the
bic_target calculated as the proper CUBIC cwnd at time
t=tcp_time_stamp+rtt does not increase, because tcp_time_stamp only
increases on jiffy tick boundaries.
So since the cnt is set to:
ca->cnt = cwnd / (bic_target - cwnd);
as cwnd increases but bic_target does not increase due to jiffy
granularity, the cnt becomes too large, causing cwnd to increase
too slowly.
For example:
- suppose at the beginning of a jiffy, cwnd=40, bic_target=44
- so CUBIC sets:
ca->cnt = cwnd / (bic_target - cwnd) = 40 / (44 - 40) = 40/4 = 10
- suppose we get 10 acks, each for 1 segment, so tcp_cong_avoid_ai()
increases cwnd to 41
- so CUBIC sets:
ca->cnt = cwnd / (bic_target - cwnd) = 41 / (44 - 41) = 41 / 3 = 13
So now CUBIC will wait for 13 packets to be ACKed before increasing
cwnd to 42, insted of 10 as it should.
The fix is to avoid adjusting the slope (determined by ca->cnt)
multiple times within a jiffy, and instead skip to compute the Reno
cwnd, the "TCP friendliness" code path.
Reported-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change CUBIC to properly handle stretch ACKs in additive increase mode
by passing in the count of ACKed packets to tcp_cong_avoid_ai().
In addition, because we are now precisely accounting for stretch ACKs,
including delayed ACKs, we can now remove the delayed ACK tracking and
estimation code that tracked recent delayed ACK behavior in
ca->delayed_ack.
Reported-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change Reno to properly handle stretch ACKs in additive increase mode
by passing in the count of ACKed packets to tcp_cong_avoid_ai().
In addition, if snd_cwnd crosses snd_ssthresh during slow start
processing, and we then exit slow start mode, we need to carry over
any remaining "credit" for packets ACKed and apply that to additive
increase by passing this remaining "acked" count to
tcp_cong_avoid_ai().
Reported-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_cong_avoid_ai() was too timid (snd_cwnd increased too slowly) on
"stretch ACKs" -- cases where the receiver ACKed more than 1 packet in
a single ACK. For example, suppose w is 10 and we get a stretch ACK
for 20 packets, so acked is 20. We ought to increase snd_cwnd by 2
(since acked/w = 20/10 = 2), but instead we were only increasing cwnd
by 1. This patch fixes that behavior.
Reported-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LRO, GRO, delayed ACKs, and middleboxes can cause "stretch ACKs" that
cover more than the RFC-specified maximum of 2 packets. These stretch
ACKs can cause serious performance shortfalls in common congestion
control algorithms that were designed and tuned years ago with
receiver hosts that were not using LRO or GRO, and were instead
politely ACKing every other packet.
This patch series fixes Reno and CUBIC to handle stretch ACKs.
This patch prepares for the upcoming stretch ACK bug fix patches. It
adds an "acked" parameter to tcp_cong_avoid_ai() to allow for future
fixes to tcp_cong_avoid_ai() to correctly handle stretch ACKs, and
changes all congestion control algorithms to pass in 1 for the ACKed
count. It also changes tcp_slow_start() to return the number of packet
ACK "credits" that were not processed in slow start mode, and can be
processed by the congestion control module in additive increase mode.
In future patches we will fix tcp_cong_avoid_ai() to handle stretch
ACKs, and fix Reno and CUBIC handling of stretch ACKs in slow start
and additive increase mode.
Reported-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The smp_unregister() function needs to be called every time the
controller is powered down. There are multiple entry points when
this can happen. One is "hciconfig hci0 reset" which will throw
a WARN_ON when LE support has been enabled.
[ 78.564620] WARNING: CPU: 0 PID: 148 at net/bluetooth/smp.c:3075 smp_register+0xf1/0x170()
[ 78.564622] Modules linked in:
[ 78.564628] CPU: 0 PID: 148 Comm: kworker/u3:1 Not tainted 3.19.0-rc4-devel+ #404
[ 78.564629] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
[ 78.564635] Workqueue: hci0 hci_rx_work
[ 78.564638] ffffffff81b4a7a2 ffff88001cb2fb38 ffffffff8161d881 0000000080000000
[ 78.564642] 0000000000000000 ffff88001cb2fb78 ffffffff8103b870 696e55206e6f6f6d
[ 78.564645] ffff88001d965000 0000000000000000 0000000000000000 ffff88001d965000
[ 78.564648] Call Trace:
[ 78.564655] [<ffffffff8161d881>] dump_stack+0x4f/0x7b
[ 78.564662] [<ffffffff8103b870>] warn_slowpath_common+0x80/0xc0
[ 78.564667] [<ffffffff81544b00>] ? add_uuid+0x1f0/0x1f0
[ 78.564671] [<ffffffff8103b955>] warn_slowpath_null+0x15/0x20
[ 78.564674] [<ffffffff81562d81>] smp_register+0xf1/0x170
[ 78.564680] [<ffffffff81081236>] ? lock_timer_base.isra.30+0x26/0x50
[ 78.564683] [<ffffffff81544bf0>] powered_complete+0xf0/0x120
[ 78.564688] [<ffffffff8152e622>] hci_req_cmd_complete+0x82/0x260
[ 78.564692] [<ffffffff8153554f>] hci_cmd_complete_evt+0x6cf/0x2e20
[ 78.564697] [<ffffffff81623e43>] ? _raw_spin_unlock_irqrestore+0x13/0x30
[ 78.564701] [<ffffffff8106b0af>] ? __wake_up_sync_key+0x4f/0x60
[ 78.564705] [<ffffffff8153a2ab>] hci_event_packet+0xbcb/0x2e70
[ 78.564709] [<ffffffff814094d3>] ? skb_release_all+0x23/0x30
[ 78.564711] [<ffffffff81409529>] ? kfree_skb+0x29/0x40
[ 78.564715] [<ffffffff815296c8>] hci_rx_work+0x1c8/0x3f0
[ 78.564719] [<ffffffff8105bd91>] ? get_parent_ip+0x11/0x50
[ 78.564722] [<ffffffff8105be25>] ? preempt_count_add+0x55/0xb0
[ 78.564727] [<ffffffff8104f65f>] process_one_work+0x12f/0x360
[ 78.564731] [<ffffffff8104ff9b>] worker_thread+0x6b/0x4b0
[ 78.564735] [<ffffffff8104ff30>] ? cancel_delayed_work_sync+0x10/0x10
[ 78.564738] [<ffffffff810542fa>] kthread+0xea/0x100
[ 78.564742] [<ffffffff81620000>] ? __schedule+0x3e0/0x980
[ 78.564745] [<ffffffff81054210>] ? kthread_create_on_node+0x180/0x180
[ 78.564749] [<ffffffff816246ec>] ret_from_fork+0x7c/0xb0
[ 78.564752] [<ffffffff81054210>] ? kthread_create_on_node+0x180/0x180
[ 78.564755] ---[ end trace 8b0d943af76d3736 ]---
This warning is not critical and has only been placed in the code to
actually catch this exact situation. To avoid triggering it move
the smp_unregister() into hci_dev_do_close() which will now also
take care of remove the SMP channel. It is safe to call this function
since it only remove the channel if it has been previously registered.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When receiving a HCI Hardware Error event, the controller should be
assumed to be non-functional until issuing a HCI Reset command.
The Bluetooth hardware errors are vendor specific and so add a
new hdev->hw_error callback that drivers can provide to run extra
code to handle the hardware error.
After completing the vendor specific error handling perform a full
reset of the Bluetooth stack by closing and re-opening the transport.
Based-on-patch-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Split the hci_dev_reset ioctl handling into using hci_dev_do_reset
helper function. Similar to what has been done with hci_dev_do_open
and hci_dev_do_close.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The discovery state should be set to stopped when the HCI device is
powered off. This patch adds the appropriate call to the
hci_discovery_set_state() function from hci_dev_do_close() which is
responsible for the power-off procedure.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When HCI_Reset is issued the discovery state is assumed to be stopped.
The hci_cc_reset() handler was trying to set the state but it was doing
it without using the hci_discovery_set_state() function. Because of this
e.g. the mgmt Discovering event could go without being sent. This patch
fixes the code to use the hci_discovery_set_state() function instead of
just blindly setting the state value.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There's a check in set_secure_conn() that's supposed to ensure that SSP
is enabled before we try to request the controller to enable SC (since
SSP is a pre-requisite for it). However, this check only makes sense for
controllers actually supporting BR/EDR SC. If we have a 4.0 controller
we're only interested in the LE part of SC and should therefore not be
requiring SSP to be enabled. This patch adds an additional condition to
check for lmp_sc_capable(hdev) before requiring SSP to be enabled.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If Secure Connections Only mode has been enabled, the it is important
to check that OOB data for P-256 values is provided. In case it is not,
then tell the remote side that no OOB data is present.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When replying to the IO capability request for Secure Simple Pairing and
Secure Connections, the OOB data present fields needs to set. Instead of
making the calculation inline, split this into a separate helper
function.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When Secure Connections Only mode has been enabled and remote OOB data
is requested, then only provide P-256 hash and randomizer vaulues. The
fields for P-192 hash and randomizer should be set to zero.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Until legacy SMP OOB pairing is implemented user space should be given a
clear error when trying to use it. This patch adds a corresponding check
to the Add Remote OOB Data handler function which returns "invalid
parameters" if non-zero Rand192 or Hash192 parameters were given for an
LE address.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
With the newly introduced pipes table hci_dev fields,
the nfc_hci_pipe2gate routine is no longer needed.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When a command is received, it is sometime needed to let the CLF driver do
some additional operations. (ex: count remaining pipe notification...)
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We update the tracked pipes status when receiving HCI commands.
Also we forward HCI errors and we reply to any HCI command, even though
we don't support it.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As there can be several pipes connected to the same gate, we need
to know which pipe ID to use when sending an HCI response. A gate
ID is not enough.
Instead of changing the nfc_hci_send_response() API to something
not aligned with the rest of the HCI API, we call nfc_hci_hcp_message_tx
directly.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to keep host source information on specific hci event (such as
evt_connectivity or evt_transaction) and because 2 pipes can be connected
to the same gate, it is necessary to add a table referencing every pipe
with a {gate, host} tuple.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Several pipes may point to the same CLF gate, so getting the gate ID
as an input is not enough.
For example dual secure element may have 2 pipes (1 for uicc and
1 for eSE) pointing to the connectivity gate.
As resolving gate and host IDs can be done from a pipe, we now pass
the pipe ID to the event received handler.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This allows mac80211 to configure BIP-GMAC-128 and BIP-GMAC-256 to the
driver and also use software-implementation within mac80211 when the
driver does not support this with hardware accelaration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows mac80211 to configure BIP-CMAC-256 to the driver and also
use software-implementation within mac80211 when the driver does not
support this with hardware accelaration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows mac80211 to configure CCMP-256 to the driver and also use
software-implementation within mac80211 when the driver does not support
this with hardware accelaration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[squash ccmp256 -> mic_len argument change]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows mac80211 to configure GCMP and GCMP-256 to the driver and
also use software-implementation within mac80211 when the driver does
not support this with hardware accelaration.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[remove a spurious newline]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This makes cfg80211 aware of the GCMP, GCMP-256, CCMP-256, BIP-GMAC-128,
BIP-GMAC-256, and BIP-CMAC-256 cipher suites. These new cipher suites
were defined in IEEE Std 802.11ac-2013.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This cipher can be used only as a group management frame cipher and as
such, there is no point in validating that it is not used with non-zero
key-index. Instead, verify that it is not used as a pairwise cipher
regardless of the key index.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
[change code to use switch statement which is easier to extend]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If suspend starts while ieee80211_scan_completed() is running, between
the point where SCAN_COMPLETED is set and the work is queued,
ieee80211_scan_cancel() will not catch the work and we may finish
suspending before the work is actually executed, leaving the scan
running while suspended.
To fix this race, queue the scan work during resume if the
SCAN_COMPLETED flag is set and flush it immediately.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The socket already carries the net namespace with it so there is
no need to be passing another net around.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
ipsec 2015-01-26
Just two small fixes for _decode_session6() where we
might decode to wrong header information in some rare
situations.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lubomir Rintel reported that during replacing a route the interface
reference counter isn't correctly decremented.
To quote bug <https://bugzilla.kernel.org/show_bug.cgi?id=91941>:
| [root@rhel7-5 lkundrak]# sh -x lal
| + ip link add dev0 type dummy
| + ip link set dev0 up
| + ip link add dev1 type dummy
| + ip link set dev1 up
| + ip addr add 2001:db8:8086::2/64 dev dev0
| + ip route add 2001:db8:8086::/48 dev dev0 proto static metric 20
| + ip route add 2001:db8:8088::/48 dev dev1 proto static metric 10
| + ip route replace 2001:db8:8086::/48 dev dev1 proto static metric 20
| + ip link del dev0 type dummy
| Message from syslogd@rhel7-5 at Jan 23 10:54:41 ...
| kernel:unregister_netdevice: waiting for dev0 to become free. Usage count = 2
|
| Message from syslogd@rhel7-5 at Jan 23 10:54:51 ...
| kernel:unregister_netdevice: waiting for dev0 to become free. Usage count = 2
During replacement of a rt6_info we must walk all parent nodes and check
if the to be replaced rt6_info got propagated. If so, replace it with
an alive one.
Fixes: 4a287eba2d ("IPv6 routing, NLM_F_* flag support: REPLACE and EXCL flags support, warn about missing CREATE flag")
Reported-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Tested-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: David S. Miller <davem@davemloft.net>
An exception is seen in ICMP ping receive path where the skb
destructor sock_rfree() tries to access a freed socket. This happens
because ping_rcv() releases socket reference with sock_put() and this
internally frees up the socket. Later icmp_rcv() will try to free the
skb and as part of this, skb destructor is called and which leads
to a kernel panic as the socket is freed already in ping_rcv().
-->|exception
-007|sk_mem_uncharge
-007|sock_rfree
-008|skb_release_head_state
-009|skb_release_all
-009|__kfree_skb
-010|kfree_skb
-011|icmp_rcv
-012|ip_local_deliver_finish
Fix this incorrect free by cloning this skb and processing this cloned
skb instead.
This patch was suggested by Eric Dumazet
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jon Paul Maloy