Add a few statements to debug channel context operation.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
kfree() null-checks its argument.
Found by smatch.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the missing null termination after strncpy().
This isn't actually a buffer overflow in this case since we use
snprintf() appropriately to fill the buffer passed by the caller,
but in the interest of not turning this into a bug down the road,
go ahead and force termination here.
Found by Coverity.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rxs->rate_idx is unsigned, so it will always be >= 0.
Found by Coverity.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The files ray_cs.h and rayctl.h both contain two thirds of what
appears to be an include guard using the macro name RAYLINK_H (both
lack the #define). Since RAYLINK_H is not defined anywhere, the
#ifndefs are confusing no-ops. Add proper include guards using
different macro names.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Newer firmware returns API revision in GET_HW_SPEC command
response. We will make use of it instead of parsing this
information from FW release number.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We will remove 'fw' prefix from these variable and macro
names and make them generic.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While updating 'left_len' in each iteration, we should subtract
last TLV length not the accumulated length of TLVs parsed till
now.
This bug in parsing logic is exposed by newer firmware which adds
two TLVs in GET_HW_SPEC command response. Earlier firmwares used to
add only one TLV.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on a quick test with AR9271, TDLS seems to be working fine.
Tests were done with 2 Atheros AR9271 based devices with firmware
1.3 (sha1 8d49f928aa40ac53c729189bff1333cd373a7fb5), associated
with a WAP54G access point. TDLS worked fine both in WPA2 mode and
without encryption. Stations maintained ping flood traffic between
each other and towards the AP without significant losses.
Not tested with AR7010.
TDLS was enabled in earlier patches the same way for other
Atheros drivers:
ath9k (fd6562344d),
and carl9170 (d1f3de71a5).
Signed-off-by: Csaba Kiraly <csaba.kiraly@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some copy engine structures are target specific
and are uploaded to the device during
init/configuration.
This also cleans up a bit diag_mem_read/write
implicit byteswap mess leaving only
diag_access_read/write with an implicit endianess
byteswap.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The mapping is already defined in a structure. It
makes little sense to duplicate information stored
in it within a function.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It doesn't make much sense to have copy engine
configuration structures spread across the whole
source file.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Recent crash dump patches introduced a regression.
If debugfs was disabled upon crash user could only
see the following:
[ 793.880000] ath10k: firmware crashed! (uuid n/a)
[ 793.890000] ath10k: qca988x hw2.0 (0x4100016c, 0x043202ff) fw 10.1.467.2-1 api 2 htt 2.1
[ 793.890000] ath10k: debug 0 debugfs 0 tracing 0 dfs 1
The report was missing register dump. Fix it by
printing registers regardless if crash_data is
present or not.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes it a lot easier to log and debug
messages if there's more than 1 ath10k device on a
system.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When using the cfg80211_inform_bss[_width]() functions drivers
cannot currently indicate whether the data was received in a
beacon or probe response. Fix that by passing a new enum that
indicates such (or unknown).
For good measure, use it in ath6kl.
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> [ath6kl]
Acked-by: Arend van Spriel <arend@broadcom.com> [brcmfmac]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the cfg80211_rx_mgmt(), parameter @gfp was used for the memory allocation.
But, memory get allocated under spin_lock_bh(), this implies atomic context.
So, one can't use GFP_KERNEL, only variants with no __GFP_WAIT. Actually, in all
occurrences GFP_ATOMIC is used (wil6210 use GFP_KERNEL by mistake),
and it should be this way or warning triggered in the memory allocation code.
Remove @gfp parameter as no actual choice exist, and use hard coded
GFP_ATOMIC for memory allocation.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedef for
local_info_t. Also, the name of the struct is changed to drop the _t,
to make the name look less typedef-like.
The following Coccinelle semantic patch detects the case:
@tn@
identifier i;
type td;
@@
-typedef
struct i { ... }
-td
;
@@
type tn.td;
identifier tn.i;
@@
-td
+ struct i
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replacing strncpy with strlcpy to avoid strings that lacks null terminate.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces the use of devm_kzalloc and does away with the
kfrees in the probe and remove functions. Also, a couple of labels and
the initial assignment of the ret variable in the probe function are
removed.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'wil' released in wil_if_free(); save iomapped address aside to
properly unmap it.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the wil_priv_deinit(), wdev->netdev is accessed, so free_netdev()
should not be called before mentioned call.
Set wdev->netdev to NULL Make sure no more attempts to use it.
It is used for debug printk if not NULL.
This fix kernel panic on module unload and in case error on probe;
if memory allocation debugging enabled.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a module parameter to support setting the maximum
number of stations that can be associated to an AP.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When sending scan request, if hardware is not ready, scan timer was started
and scan timeout mis-reported.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When reading 'bf' file on debugfs, query beam forming status from firmware.
Ignore CID's that return error or return all zeros.
Remove obsolete code that used to maintain statistics on per-device basis,
as now it is reported be per-CID and current.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Define tables for similar file entries, i.e.
- table for debugfs_create_file
- table for static parameters
- table for parameters that are members of "wil" structure
- table for blobs
- table for interrupt controllers
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If firmware broken on the boot time, Sparrow card enumerates as
device 0x302 instead of 0x310. Allow using this ID
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Typical time for hardware reset, as measured, is about 200..250 msec.
Adjust sleeping to use more relaxed msleep, increase sleep interval
and increase total sleep time to be about 1sec
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When resetting target in wil_target_reset(), error may occur.
Indicate error via error code. In case of error, don't attempt to further
interact with card, specifically don't attempt firmware download or
interrupts enabling.
Move wil_rx_fini() to be always executed to prevent memory leak.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix Copyright headers in all files changed in 2014, to mention 2014
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is important to halt USER CPU first, then MAC CPU
Otherwise, race happens in the firmware
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
expose reading RGF_MAC_MTRL_COUNTER_0 in debugfs
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The prefix suggests the number should be printed in hex, so use
the %x specifier to do that.
Found by using regex suggested by Joe Perches.
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Acked-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch introduces the use of devm_kzalloc and does away with the
kfrees in the probe and remove functions.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch does away with free_irq in the remove function as the irq is
allocated with a devm_request_irq.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Broadcom hardware supports auto-adjustment of TX power depending on the
currently used rate. So far all calculations were handled without any
helpers (API) using big arrays and magic offsets.
It seems Broadcom recently decided to clean this up by developing PPR.
Their wlc_ppr.h can be found in open parts of the SDK.
As we plan to implement support for rate-based TX power it makes sense
to also implement our version of PPR as well.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't write them as we don't have gains configured correctly yet.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes workarounds on rev 6+ and cleans code slightly.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Access to PHY and radio registers is indirect on Broadcom hardware and
it seems that addressing on some MIPS SoCs may require flushing. So far
this problem was noticed on 0x4716 SoC only (marketing names: BCM4717,
BCM4718).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most of the PHYs use the same way of accessing registers, so move that
code to the shared place. An exception is G-PHY which sometimes access
A-PHY regs and requires special handling.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Flush radio writes as well and add some tiny optimizations (e.g.
masksetting PHY reg involves reading it, so reset the counter).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After commit 174beab7d4 ("at76c50x-usb: Don't perform DMA from stack memory")
at76_delete_device() and usb_put_dev() are called both
if at76_init_new_device() fails in at76_probe().
But at76_delete_device() does usb_put_dev(priv->dev) itself
that means double usb_put_dev().
The patch avoids the problem by moving usb_put_dev() from
at76_delete_device() to at76_disconnect().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rewrite a duplicated test to test the correct value
The Coccinelle semantic patch that finds this problem is:
// <smpl>
@@
expression E;
@@
(
* E
|| ... || E
|
* E
&& ... && E
)
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Larry.Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Transport buffers weren't flushed and processed
before queueing hw recovery request to mac80211.
This could in theory result in an unwanted htt/wmi
rx events being processed while mac80211 recovers
the device and possibly interfere or even crash
the system.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are basically no more uses for
ar_pci->started. It is also perfectly safe to call
hif_stop without hif_start now.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Structures used by these functions are now
guaranteed to remain accessible until driver is
unregistered.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The old comment was a little out of date. HTT Rx
ring is a more relevant problem when stopping
transport layer.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was possible on a host system running low on
memory to end up with no rx buffers on pci pipes.
This makes the driver more robust as it won't fail
to start if it can't allocate all rx buffers right
away. If it is fatal then upper layers will notice
trouble anyway.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's not really necessary to have a dedicated irq
handler just for the sake of catching early fw
crashes anymore. It is now safe to use one handler
even during early stages of device boot up.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This fixes two corner cases.
One is a race between disabling copy engine
interrupts and unhandled pending interrupts on the
host. This could end up with a runaway tasklet and
consequently memory leak of a few copy engine
rx buffers.
The other one is an unexpected (and non-maskable
via device CSR) MSI fw indication interrupt during
teardown. This could trigger the same problem as
the first corner case.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It doesn't make much sense to overwrite send_cb
and recv_cb callbacks over and over again whenever
transport starts. Just make sure to unmask copy
engine interrupts when starting.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It doesn't make sense to re-init irqs completely
whenever transport is started/stopped. Do it just
once upon probing/removing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Wrong register was being set up. This could
prevent firmware from booting in some rare cases
when using legacy interrupts.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware probing is done only once when driver is
registered and firmware version is guaranteed to
remain the same until driver is unregistered.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sometimes users forget to include important info like firmware version,
so better to print all the info.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Better to have a clear name for the function. While at it, clear up the title
for the register dump.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Store the firmware registers and other relevant data to a firmware crash dump
file and provide it to user-space via debugfs. Should help with figuring out
why the firmware crashed.
kvalo: remove dbglog support, rework and refactor the code to avoid ifdefs and
otherwise simplify it as well
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath10k_pci_diag_read32() is for reading u32 from a device and ath10k_pci_diag_read_hi()
is a helper for reading data using "host interest" table.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Service mapping for main firmware branch was incorrectly used for 10.x firmware
and vice-versa. This caused wmi_services in debugfs to print wrong values.
This fixes commit cff990ce7d ("ath10k: fix wmi service bitmap debug") where
for some reason there was either a conflict that wasn't resolved properly or
git had a bad day.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Miscellaneous
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jJGu
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull DEFINE_PCI_DEVICE_TABLE removal from Bjorn Helgaas:
"Part two of the PCI changes for v3.17:
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
It's a mechanical change that removes uses of the
DEFINE_PCI_DEVICE_TABLE macro. I waited until later in the merge
window to reduce conflicts, but it's possible you'll still see a few"
* tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Remove DEFINE_PCI_DEVICE_TABLE macro use
John W. Linville says:
====================
pull request: wireless 2014-08-14
Please pull this batch of fixes intended for the 3.17 stream...
Arend van Spriel brings two brcmfmac fixes, one which fixes a memory
leak and one which corrects some merge damage.
Emmanuel Grumbach fixes Linus's iwlwifi firmware-related log spam.
Rickard Strandqvist does some proper NULL termination after a call
to strncpy.
Ronald Wahl corrects a carl9170 problem with sending URBs with the
wrong endpoint type (resulting in log spam).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are firmwares which don't support scheduled scan.
Disable it for now.
Linus's system encoutered this issue.
Thanks to David Spinadel for his help.
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If spectral is unregistered after mac80211, the relayfs file has already
been removed recursively by mac/cfg80211, and spectral tries to remove
the file once more, thus leading to double free problems. Better clean
up spectral before to avoid that problem.
Reported-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds device ID 402 to support QCA6234X found in APQ8064 SOC
in IFC6410 board.
Tested with mainline mmci sdio driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Check vdev map has space before calling ffs,
fix invalid cleanup in failure to create vdev
case.
Open-code the BIT() logic since BIT does not properly
handle 64-bit bitfields and future patches will make
use of larger bitfields.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pull networking fixes from David Miller:
"Several networking final fixes and tidies for the merge window:
1) Changes during the merge window unintentionally took away the
ability to build bluetooth modular, fix from Geert Uytterhoeven.
2) Several phy_node reference count bug fixes from Uwe Kleine-König.
3) Fix ucc_geth build failures, also from Uwe Kleine-König.
4) Fix klog false positivies when netlink messages go to network
taps, by properly resetting the network header. Fix from Daniel
Borkmann.
5) Sizing estimate of VF netlink messages is too small, from Jiri
Benc.
6) New APM X-Gene SoC ethernet driver, from Iyappan Subramanian.
7) VLAN untagging is erroneously dependent upon whether the VLAN
module is loaded or not, but there are generic dependencies that
matter wrt what can be expected as the SKB enters the stack.
Make the basic untagging generic code, and do it unconditionally.
From Vlad Yasevich.
8) xen-netfront only has so many slots in it's transmit queue so
linearize packets that have too many frags. From Zoltan Kiss.
9) Fix suspend/resume PHY handling in bcmgenet driver, from Florian
Fainelli"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (55 commits)
net: bcmgenet: correctly resume adapter from Wake-on-LAN
net: bcmgenet: update UMAC_CMD only when link is detected
net: bcmgenet: correctly suspend and resume PHY device
net: bcmgenet: request and enable main clock earlier
net: ethernet: myricom: myri10ge: myri10ge.c: Cleaning up missing null-terminate after strncpy call
xen-netfront: Fix handling packets on compound pages with skb_linearize
net: fec: Support phys probed from devicetree and fixed-link
smsc: replace WARN_ON() with WARN_ON_SMP()
xen-netback: Don't deschedule NAPI when carrier off
net: ethernet: qlogic: qlcnic: Remove duplicate object file from Makefile
wan: wanxl: Remove typedefs from struct names
m68k/atari: EtherNEC - ethernet support (ne)
net: ethernet: ti: cpmac.c: Cleaning up missing null-terminate after strncpy call
hdlc: Remove typedefs from struct names
airo_cs: Remove typedef local_info_t
atmel: Remove typedef atmel_priv_ioctl
com20020_cs: Remove typedef com20020_dev_t
ethernet: amd: Remove typedef local_info_t
net: Always untag vlan-tagged traffic on input.
drivers: net: Add APM X-Gene SoC ethernet driver support.
...
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This is not necessary anymore. There are no more
uncontrolled htc tx entry points.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make probe/remove functions shorter and easier to
understand.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ATH10K_PCI_FEATURE_MSI_X was originally
introduced to support both chips QCA988Xv1 and
QCA988Xv2. Since v1 isn't supported anymore it
doesn't make sense to keep the feature flag
around. Since this is the last one remove the
whole thing.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The soc powersave was disabled by default. It
never was fully tested. Some hw apparently had
problems with it and the implementation itself had
a possible race.
Just remove the refcounting and simply wake up the
device when probing and put to sleep when
removing.
kvalo: make ath10k_pci_wake() and _sleep() static
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the common convention of embedding private
structures inside parent structures. This
reduces allocations and simplifies pci probing
code.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This aims at fixing some rare scan bugs related to
firmware reporting unexpected scan event
sequences.
One such bug was if spectral scan phyerr reporting
prevented firmware from properly propagating scan
events to host. This led to scan timeout. After
that next scan would trigger scan completed event
first (before scan started event) leading to
ar->scan.in_progress and timeout timer states to
be overwritten incorrectly and making the very
next scan to hang forever.
Reported-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This also reduces the cruft of printing scan event
names in capitals.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The 10.x and main firmware branches have
conflicting WMI service bitmap definitions.
This also fixes WMI services parsing on big-endian
hosts and changes debugfs output to be more human
friendly.
kvalo: remove braces and the last semicolon from SVCSTR()
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedef for
local_info_t. Also, the name of the struct is changed to drop the _t,
to make the name look less typedef-like.
The following Coccinelle semantic patch detects the case:
@tn@
identifier i;
type td;
@@
-typedef
struct i { ... }
-td
;
@@
type tn.td;
identifier tn.i;
@@
-td
+ struct i
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux kernel coding style guidelines suggest not using typedefs
for structure types. This patch gets rid of the typedef for
atmel_priv_ioctl.
The following Coccinelle semantic patch detects the case:
@tn@
identifier i;
type td;
@@
-typedef
struct i { ... }
-td
;
@@
type tn.td;
identifier tn.i;
@@
-td
+ struct i
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added a guaranteed null-terminate after call to strncpy.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The kbuild robot came up with the following warning:
tree: .../kernel/git/linville/wireless-next.git master
head: dc6be9f54a
commit: 9a1bb60250
[5/13] brcmfmac: Adding msgbuf protocol.
coccinelle warnings:
drivers/net/wireless/brcm80211/brcmfmac/msgbuf.c:1309:1-28:
alloc with no test, possible model on line 1318
Looking into the issue, it turned out that the referred allocation
buffer was not being released in failure path nor upon module
unload.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Running coccicheck on brcm80211 drivers resulted in following report:
$ make coccicheck MODE=report M=drivers/net/wireless/brcm80211
drivers/net/wireless/brcm80211/brcmfmac/pcie.c:595:2-43:
code aligned with following code on line 596
It revealed that due to a merge failure a block statement lost its
curly braces where it should not.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver assumes that endpoint 4 is always an interrupt endpoint.
Unfortunately the type differs between high-speed and full-speed
configurations while in the former case it is indeed an interrupt
endpoint this is not true for the latter case - here it is a bulk
endpoint. When sending URBs with the wrong type the kernel will
generate a warning message including backtrace. In this specific
case there will be a huge amount of warnings which can bring the system
to freeze.
To fix this we are now sending URBs to endpoint 4 using the type
found in the endpoint descriptor.
A side note: The carl9170 firmware currently specifies endpoint 4 as
interrupt endpoint even in the full-speed configuration but this has
no relevance because before this firmware is loaded the endpoint type
is as described above and after the firmware is running the stick is not
reenumerated and so the old descriptor is used.
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the now unnecessary memset too.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the now unnecessary memset too.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the now unnecessary memset too.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It must be tristate to avoid broken dependencies with kernel built-in
usb network drivers when usb support is module only.
When net config option is set, least surprize default should match usb.
Wireless RNDIS USB driver used to select USB_USBNET. USB_USBNET now
depends on USB_NET_DRIVERS so the latter should be selected as well.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Highlights:
1) Steady transitioning of the BPF instructure to a generic spot so
all kernel subsystems can make use of it, from Alexei Starovoitov.
2) SFC driver supports busy polling, from Alexandre Rames.
3) Take advantage of hash table in UDP multicast delivery, from David
Held.
4) Lighten locking, in particular by getting rid of the LRU lists, in
inet frag handling. From Florian Westphal.
5) Add support for various RFC6458 control messages in SCTP, from
Geir Ola Vaagland.
6) Allow to filter bridge forwarding database dumps by device, from
Jamal Hadi Salim.
7) virtio-net also now supports busy polling, from Jason Wang.
8) Some low level optimization tweaks in pktgen from Jesper Dangaard
Brouer.
9) Add support for ipv6 address generation modes, so that userland
can have some input into the process. From Jiri Pirko.
10) Consolidate common TCP connection request code in ipv4 and ipv6,
from Octavian Purdila.
11) New ARP packet logger in netfilter, from Pablo Neira Ayuso.
12) Generic resizable RCU hash table, with intial users in netlink and
nftables. From Thomas Graf.
13) Maintain a name assignment type so that userspace can see where a
network device name came from (enumerated by kernel, assigned
explicitly by userspace, etc.) From Tom Gundersen.
14) Automatic flow label generation on transmit in ipv6, from Tom
Herbert.
15) New packet timestamping facilities from Willem de Bruijn, meant to
assist in measuring latencies going into/out-of the packet
scheduler, latency from TCP data transmission to ACK, etc"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1536 commits)
cxgb4 : Disable recursive mailbox commands when enabling vi
net: reduce USB network driver config options.
tg3: Modify tg3_tso_bug() to handle multiple TX rings
amd-xgbe: Perform phy connect/disconnect at dev open/stop
amd-xgbe: Use dma_set_mask_and_coherent to set DMA mask
net: sun4i-emac: fix memory leak on bad packet
sctp: fix possible seqlock seadlock in sctp_packet_transmit()
Revert "net: phy: Set the driver when registering an MDIO bus device"
cxgb4vf: Turn off SGE RX/TX Callback Timers and interrupts in PCI shutdown routine
team: Simplify return path of team_newlink
bridge: Update outdated comment on promiscuous mode
net-timestamp: ACK timestamp for bytestreams
net-timestamp: TCP timestamping
net-timestamp: SCHED timestamp on entering packet scheduler
net-timestamp: add key to disambiguate concurrent datagrams
net-timestamp: move timestamp flags out of sk_flags
net-timestamp: extend SCM_TIMESTAMPING ancillary data struct
cxgb4i : Move stray CPL definitions to cxgb4 driver
tcp: reduce spurious retransmits due to transient SACK reneging
qlcnic: Initialize dcbnl_ops before register_netdev
...
Pull timer and time updates from Thomas Gleixner:
"A rather large update of timers, timekeeping & co
- Core timekeeping code is year-2038 safe now for 32bit machines.
Now we just need to fix all in kernel users and the gazillion of
user space interfaces which rely on timespec/timeval :)
- Better cache layout for the timekeeping internal data structures.
- Proper nanosecond based interfaces for in kernel users.
- Tree wide cleanup of code which wants nanoseconds but does hoops
and loops to convert back and forth from timespecs. Some of it
definitely belongs into the ugly code museum.
- Consolidation of the timekeeping interface zoo.
- A fast NMI safe accessor to clock monotonic for tracing. This is a
long standing request to support correlated user/kernel space
traces. With proper NTP frequency correction it's also suitable
for correlation of traces accross separate machines.
- Checkpoint/restart support for timerfd.
- A few NOHZ[_FULL] improvements in the [hr]timer code.
- Code move from kernel to kernel/time of all time* related code.
- New clocksource/event drivers from the ARM universe. I'm really
impressed that despite an architected timer in the newer chips SoC
manufacturers insist on inventing new and differently broken SoC
specific timers.
[ Ed. "Impressed"? I don't think that word means what you think it means ]
- Another round of code move from arch to drivers. Looks like most
of the legacy mess in ARM regarding timers is sorted out except for
a few obnoxious strongholds.
- The usual updates and fixlets all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
timekeeping: Fixup typo in update_vsyscall_old definition
clocksource: document some basic timekeeping concepts
timekeeping: Use cached ntp_tick_length when accumulating error
timekeeping: Rework frequency adjustments to work better w/ nohz
timekeeping: Minor fixup for timespec64->timespec assignment
ftrace: Provide trace clocks monotonic
timekeeping: Provide fast and NMI safe access to CLOCK_MONOTONIC
seqcount: Add raw_write_seqcount_latch()
seqcount: Provide raw_read_seqcount()
timekeeping: Use tk_read_base as argument for timekeeping_get_ns()
timekeeping: Create struct tk_read_base and use it in struct timekeeper
timekeeping: Restructure the timekeeper some more
clocksource: Get rid of cycle_last
clocksource: Move cycle_last validation to core code
clocksource: Make delta calculation a function
wireless: ath9k: Get rid of timespec conversions
drm: vmwgfx: Use nsec based interfaces
drm: i915: Use nsec based interfaces
timekeeping: Provide ktime_get_raw()
hangcheck-timer: Use ktime_get_ns()
...
Conflicts:
net/6lowpan/iphc.c
Minor conflicts in iphc.c were changes overlapping with some
style cleanups.
John W. Linville says:
====================
Please pull this last(?) batch of wireless change intended for the
3.17 stream...
For the NFC bits, Samuel says:
"This is a rather quiet one, we have:
- A new driver from ST Microelectronics for their NCI ST21NFCB,
including device tree support.
- p2p support for the ST21NFCA driver
- A few fixes an enhancements for the NFC digital laye"
For the Atheros bits, Kalle says:
"Michal and Janusz did some important RX aggregation fixes, basically we
were missing RX reordering altogether. The 10.1 firmware doesn't support
Ad-Hoc mode and Michal fixed ath10k so that it doesn't advertise Ad-Hoc
support with that firmware. Also he implemented a workaround for a KVM
issue."
For the Bluetooth bits, Gustavo and Johan say:
"To quote Gustavo from his previous request:
'Some last minute fixes for -next. We have a fix for a use after free in
RFCOMM, another fix to an issue with ADV_DIRECT_IND and one for ADV_IND with
auto-connection handling. Last, we added support for reading the codec and
MWS setting for controllers that support these features.'
Additionally there are fixes to LE scanning, an update to conform to the 4.1
core specification as well as fixes for tracking the page scan state. All
of these fixes are important for 3.17."
And,
"We've got:
- 6lowpan fixes/cleanups
- A couple crash fixes, one for the Marvell HCI driver and another in LE SMP.
- Fix for an incorrect connected state check
- Fix for the bondable requirement during pairing (an issue which had
crept in because of using "pairable" when in fact the actual meaning
was "bondable" (these have different meanings in Bluetooth)"
Along with those are some late-breaking hardware support patches in
brcmfmac and b43 as well as a stray ath9k patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This converts a driver in drivers/net/* to use the
module_usb_driver() macro which makes the code smaller and a
bit simpler.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Adds the spectral scan feature for ath10k. The spectral scan is triggered by
configuring a mode through a debugfs control file. Samples can be gathered via
another relay debugfs file.
Essentially, to try it out:
ip link set dev wlan0 up
echo background > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
echo trigger > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
iw dev wlan0 scan
echo disable > /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan_ctl
cat /sys/kernel/debug/ieee80211/phy0/ath10k/spectral_scan0 > samples
This feature is still experimental. Based on the original RFC patch of
Sven Eckelmann.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath9k and ath10k will share the definitions of the debugfs spectral
structures and enums. Having them in the same place helps to avoid conflicts.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In some cases during heavy tx vdev stop-start
would timeout on vdev synchronization causing
traffic to stall for a few seconds.
Instead of stop-starting use a dedicated vdev
restart command and down vdevs explicitly before
doing so.
This gets rid of the synchronization
warnings/timeouts and makes channel switching
smoother during traffic.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When switching from one 5 GHz channel to another 5 GHz channel we need
to make sure BPHY is still in a reset. However to access BPHY register
we have to switch to 2 GHz mode for a moment. Otherwise this may result
in "Data bus error" (noticed by Hauke with BCM43224 connected to the
SoC).
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add lists of chipsets, so people can enable support for their device
easier (at least after checking lspci).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TDLS connections require dedicated flowrings. This patches adds
TDLS event handling and flowring creation/deletion based on these
events.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Msgbuf flow control was using a function to flow off and on which
was not supported without proptx enabled. Also flow control needs
to be handled per ifidx.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a pcie device gets reset then the low power modes l1 and l2
should be temporarily disabled.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch will add PCIe support. With this patch the PCIe chipsets
43602, 4354, 4356, 43567, and 43570 will be supported.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch will add the msgbuf protocol. This protocol is used by
the soon to be added new bus interface PCIe. Msgbuf is a protocol
where most data is and remains located on the host (driver) side
and transferred by DMA from and to device. Msgbuf is the protocol
which takes care of the signalling of the buffers between host and
device which identifies this DMA-able data.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The soon to be added protocol msgbuf requires information about
interface addressing mode and peer deletion. This patch adds the
necessary APIs to proto, implements dummy functions in BCDC and
adds calls to proto wherever necessary by wl_cfg80211.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "c1b2053 brcmfmac: Make firmware path a module parameter"
introduced use of strcpy and strcat. The strcpy and strcat require
using null terminated strings and can cause out-of-bounds memory
access and subsequent corruption. This patch replaces these by
strncpy and strncat respectively to assure array boundaries are
not crossed.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Daniel Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Correct typo in the name of the type given to sizeof. Because it is the
size of a pointer that is wanted, the typo has no impact on compilation or
execution.
This problem was found using Coccinelle (http://coccinelle.lip6.fr/). The
semantic patch used can be found in message 0 of this patch series.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It has taken me a long long time to get the OOB interrupt working on the
AP6210 sdio wifi/bt module found on various Allwinner A20 boards. In the
end I found these magic register pokes in the cubietruck kernel tree:
7f08ba3956
This is also done for the bcm43362 in broadcom's internal/proprietary driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
[arend@broadcom.com: rebased changing BCM43362 chip id to fix compilation]
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not doing so, could fail on device probing when use_chanctx
module param is set to true.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It contains radio 0x2057 rev 14 just like a BCM43217, so it doesn't
require any magic. The main difference is that BCM4313 is 1x1:1.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmfmac devices can use an out-of-band interrupt on a GPIO line.
Currently this is specified using platform data. Add support for
specifying out-of-band interrupt via device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[arend@broadcom.com: conditionalize more of-code, use driver debug routines]
Signed-off-by: Arend van Spriel <arend@broadcom.com>
[hdegoede@redhat.com: drop clk / reg_on gpio handling, as there is no consensus
on how to handle this yet]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Print sequence number, AMSDU_MORE flag and AC when additional
debug enabled in RX path. This is usefull for debugging purpose.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
A-MSDU 4addr frames weren't reconstructed properly
and in some cases this resulted in a warning:
br0: received packet on wlan0.sta1 with own address as source address
Since this was only related to A-MSDU it would
trigger when more intense traffic was generated.
Reported-by: Vu Hai NGUYEN <vh.nguyen@actiasodielec.fr>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
John W. Linville says:
====================
pull request: wireless-next 2014-07-25
Please pull this batch of updates intended for the 3.17 stream!
For the mac80211 bits, Johannes says:
"We have a lot of TDLS patches, among them a fix that should make hwsim
tests happy again. The rest, this time, is mostly small fixes."
For the Bluetooth bits, Gustavo says:
"Some more patches for 3.17. The most important change here is the move of
the 6lowpan code to net/6lowpan. It has been agreed with Davem that this
change will go through the bluetooth tree. The rest are mostly clean up and
fixes."
and,
"Here follows some more patches for 3.17. These are mostly fixes to what
we've sent to you before for next merge window."
For the iwlwifi bits, Emmanuel says:
"I have the usual amount of BT Coex stuff. Arik continues to work
on TDLS and Ariej contributes a few things for HS2.0. I added a few
more things to the firmware debugging infrastructure. Eran fixes a
small bug - pretty normal content."
And for the Atheros bits, Kalle says:
"For ath6kl me and Jessica added support for ar6004 hw3.0, our latest
version of ar6004.
For ath10k Janusz added a printout so that it's easier to check what
ath10k kconfig options are enabled. He also added a debugfs file to
configure maximum amsdu and ampdu values. Also we had few fixes as
usual."
On top of that is the usual large batch of various driver updates --
brcmfmac, mwifiex, the TI drivers, and wil6210 all get some action.
Rafał has also been very busy with b43 and related updates.
Also, I pulled the wireless tree into this in order to resolve a
merge conflict...
P.S. The change to fs/compat_ioctl.c reflects a name change in a
Bluetooth header file...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The 10.2 firmware is a successor of 10.1 firmware
(formerly identified as 10.x). Both share a lot
but have some slight ABI differences that need to
be taken care of.
The 10.2 firmware introduces some new features but
those can be added in subsequent patches. This
patch makes ath10k boot and work with 10.2 with
comparable functionality to 10.1.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Different firmware may support different numbers of
vdevs. Use value that is always out of range for all
firmware.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The 10.x firmware does not support IBSS mode at
all. It can't beacon and it crashes when trying to
scan.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware doesn't perform Rx reordering so it is
left to the host driver to do that.
Use mac80211 to perform reordering instead of
re-inventing the wheel.
This fixes TCP throughput issues in some
environments.
Reported-by: Denton Gentry <denton.gentry@gmail.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
We have interfaces. Remove the open coded cruft. Reduces text size
along with the code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: QCA ath9k Development <ath9k-devel@qca.qualcomm.com>
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
This has been tested on 14e4:4328 (BCM4321), 14e4:432b (BCM4322),
14e4:4353 (BCM43224) and 14e4:4359 (BCM43228) which is an almost
complete list of 5 GHz capable device (only BCM43222 is missing).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We don't have all needed channel tables due to RE process for this
device.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This process requires sending some sample tone, so make sure we're
allowed to transmit first.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So far we were assuming only A-PHY supports 5 GHz.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The dividend in do_div() is expected to be an unsigned 64-bit integer,
which leads to the following warning when building for 32-bit MIPS:
drivers/net/wireless/mac80211_hwsim.c: In function 'mac80211_hwsim_set_tsf':
drivers/net/wireless/mac80211_hwsim.c:664:98: warning: comparison of distinct pointer types lacks a cast [enabled by default]
data->bcn_delta = do_div(delta, bcn_int);
Since we care about the signedness of delta when adjusting tsf_offset
and bcm_delta, use the absolute value for the division and compare
the two timestamps to determine the sign.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If an aggregation session fails, frames still end up in the driver queue
with IEEE80211_TX_CTL_AMPDU set.
This causes tx for the affected station/tid to stall, since
ath_tx_get_tid_subframe returning packets to send.
Fix this by clearing IEEE80211_TX_CTL_AMPDU as long as no aggregation
session is running.
Cc: stable@vger.kernel.org
Reported-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The DCM condition was not checked well for channel switch in both AP and
station scenarios. Teardown was also not done for AP/GO DCM. Add the
missing checks.
Reported-by: Peer, Ilan <ilan.peer@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
It was possible to enter an endless loop while
processing a single pci copy engine pipe. This
could effectively render ath10k incapable of
responding to any requests.
An example case when this could happen is when
firmware generates a lot of events, e.g. spectral
scan phyerr via WMI.
Reported-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some radios may share the same ID and revision but differ by a version.
E.g. radio in BCM5357B0 is version 1 and requires specific handling.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Newer devices need different workarounds for cores 0 and 1.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add some missing ops and prepare for new devices support. This patch is
a great stability improvement for BCM43217. Earlier Tenda W322E used to
disconnect every 2 minutes (16 times over 30 minutes). With this fix I
got it running for 4 hours (with iperf) without any disconnection.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes handling channel 14 and adds code for BCM43217.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mmc_rescan will scan for non-removable cards only once, hence the card
will not be rediscovered.
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the firmware asserts, we restart the device and reset
the relevant data we hold in the driver. BT Coex data was
not reset and because of that, the driver wouldn't
reconfigure the firmware properly after firmware restart.
Same for beacon filtering. Fix that.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When we associate, we may have heard the beacon before the
association. In that case, BSS_CHANGED_BEACON_INFO will be
set along with BSS_CHANGED_ASSOC in changes in
bss_info_change.
In this case, we didn't update the smart fifo nor beacon
filtering leaving those two feature disabled.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add the Control Status Registers to the firmware error dump
infrastructure.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Use the fw-error-dump infrastructure to dump the periphery
registers. Only certain ranges are readable, so dump only
these.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The mvm op_mode won't allocate the buffer for the transport
any more. The transport allocates its own buffer and mvm
is in charge of splicing the buffers in the debugfs hook.
This makes the repartition easier to handle.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
modinfo and kerneldoc disagreed on the meaning of this field.
Reported-by: Andrea Oliveri <oliveriandrea@gmail.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add OTP to the string: "can't parse empty OTP/NVM section"
NVM usually refers to nvm_file while the problem can be in
the OTP.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The recent unified scan api change introduced issues
when stopping ongoing scans, since both regular and
sched scan now use same stopped notification.
When issuing a new scan right after a running one,
we get the "old" notification and handle it wrongly
as notification for the current scan.
Fix it by introducing a new function that make sure
we consume the pending notifications before issuing
a new scan.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: ArikX Nemtsov <arik@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
According to new requirements, the ACK / CTS kill mask is
not related to reduced TX power anymore. This allows to
remove the code that tracked reduced TX power enablement
across different interfaces.
The ACK / CTS kill mask is now fetch from a table. It
depends on the Activity grading (activity from BT) and on
the Look Up Table (LUT) type.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The Remain On Channel framework added to the firmare is
a bit like time events. It allows the driver to request
the firmware to be on a certain channel for a certain time.
Unlike the time events, the ROC infrastructure doesn't need
a MAC context in the firmware - it uses a generic context
called "auxiliary framework".
This is useful for any offchannel activity that is not bound
to a specific MAC.
The flow is synchronized much like with time events:
1) The driver receives an action frame from the wpa_supplicant
via nl80211 that requests to be sent offchannel.
2) The driver sends an Aux ROC command (0x53) to the firmware.
3) The firmware responds with the unique id of the time event.
4) When time event starts, the driver puts the frame in the
Aux queue.
Special care needs to be taken when the time events ends:
the queue needs to be cleaned-up.
Signed-off-by: Ariej Marjieh <ariej.marjieh@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Apparently fw/hw generates a corrupted QoS Control
Field in Qos NullFunc frames. The only way to
workaround this is to downgrade frames to
NullFunc. This should be okay since powersave is
done by fw/hw and these frames are only used for
CQM purposes (e.g. from hostapd to check if
station is still connected).
This doesn't fix any user visible bug that I know
of. It just prevents from sending out funky frames
on the air.
Reported-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It always bugged me how tid is computed and stored
in a temporary var before written to the control
buffer. It was confusing and it made it difficult
to work with tx helpers.
While at it rename the qos workaround function as
it was misleading - it's not a workaround but
preparation for nwifi tx mode.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware could request inspection of some
submitted tx requests. Since the callback wasn't
implemented it was possible to bleed tx msdu_ids
which could translate to tx flushing timeouts.
There's nothing ath10k can do to help firmware
with tx processing now so just report all tx
frames as already inspected to prevent firmware
from sending up inspection events and force it to
report regular tx completion indications with
discard status.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Apparently iomap writes that unmask CE irqs aren't
propagated properly sometimes. Before failing try
to poll for the control response message as it may
have been delivered without an interrupt.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add new AUX ROC command that is intended for HS2.0 purposes.
It is used to send ANQP requests on a specific channel.
This command requests the firmware to trigger a time event
and remain on a certain channel for a given duration.
Triggering the time event is done by using the Aux
Framework in the firmware, and makes use of the Aux station
(similarly to scan).
Signed-off-by: Ariej Marjieh <ariej.marjieh@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enabling the Aux queue and mapping it to FIFO 5.
Defining the Aux queue for the Aux station.
Signed-off-by: Ariej Marjieh <ariej.marjieh@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add iwl_mvm_ref_sync() calls (with new ref types) to
flows that might access the device directly.
These calls make sure the device is out of d0i3,
and the bus is available for direct access.
Since some of these functions are reentrant, convert
the refs_bitmap to a ref counter, so multiple refs
of the same type could be taken concurrently.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
As part of thermal throttling, some data is being read from NVM.
The offset is in words, but was addressed as in octets. fixed.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In AP mode, configure the fw to pass beacons from
foreign APs, in order to be able to set the ht
protection IE properly.
Add the same filters in case of GO (which didn't have
any configured filter_flags, probably by mistake)
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of code the fixed values, use a C99 initializer.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Randy fixes a few issues in iwlwifi's Kconfig. Because of
this, 'Debugging options' was not indented under iwlwifi
using menuconfig.
I added a few other fixes on the way, like the link to the
website and added 7265 in the supported NICs.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
[ Commit message + other fixes ]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We don't need wall-clock time here, and in most configurations
that care, there are already timestamps in the kernel using
CONFIG_PRINTK_TIME=y.
Reported-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In managed mode if the driver is getting a re-associate command
from cfg80211, driver deauthenticates with the AP internally and
sends a disconnected event to cfg80211 before completion of its
association process. The disconnected event then modifies the
SSID length as wdev->ssid_len = 0. So, upon receiving the connect
result event from driver, cfg80211 is unable to get that BSS from
the device's BSS list and generates the following WARN_ON message.
WARNING: CPU: 0 PID: 857 at net/wireless/sme.c:658
__cfg80211_connect_result+0x3a6/0x3e0 [cfg80211]()
Avoid re-association while the device is already associated to a
network. Also remove the internal deauthentication from the
association path.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This local variable is not used anywhere in function.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By the way add few chipsets that were tracked with "wl" dumps.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Seems to be required by some hardware, wl does it every time.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set up tx power for each MRR segment in the tx descriptor
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Packets originally buffered for the regular hardware tx queues can end
up being transmitted through the U-APSD queue (via PS-Poll or U-APSD).
When packets are dropped due to retransmit failures, the pending frames
counter is not always updated properly.
Fix this by keeping track of the queue that a frame was accounted for in
the ath_frame_info struct, and using that on completion to decide
whether the counter should be updated.
This fixes some spurious transmit queue hangs.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just like in case of SSB SPROMs they are encoded in a bit tricky way.
SPROM struct already uses s8 type and it's supposed to store decoded
values.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New register area defined in the firmware
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware sets this register with the offset of the firmware trace area
within the peripheral memory region. Critical for the firmware trace
to work
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use single data source for all information regarding the firmware
memory map. With this change "ucode_xxx" regions disappears since
they are in fact part of larger "upper area" region
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If copy_from_user() fails, buffer allocated for parameters would leak
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Variable 'ctx' declarad again in the inner loop. Should use
one from outer loop instead.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New hardware release appears; it require some changes to properly support it.
Introduce struct wil_board and "board" attribute in wil6210_priv;
keep hardware variant information in this structure.
fill it on probe(). Used in the reset flow.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The unwanted frame types are already handled in 'default' case
of the switch/case below.
The str_ptr is allocated but it can be leaked if the length check
fails in the REQUEST/RESP cases. Fix it by allocating sta_ptr
after the length checks.
Reported-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Daniel Drake <dsd@laptop.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function brcmf_p2p_detach() was only called in error flow of the
brcmf_cfg80211_attach() routine, but it also needs to be called
upon brcmf_cfg80211_detach().
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of waiting for IFF_UP of the primary net device to determine
the band and channel information of the wiphy structure, this is now
done during driver initialization in brcmf_cfg80211_attach(). The
channel information is obtained from the device and the 2G band is
updated when 40MHz bandwidth is enabled for that band. Before this
change the band and channel objects were common between multiple
brcmfmac devices in the system, which make that information rather
unreliable. That is also fixed with this reworked implementation.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just reordering the functions in preparation of subsequent changes.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introducing a new source module that will be responsible for
identifying features and quirks related to the device being
handled.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Preparing for another patch move the functions in separate commit.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes firmware path a module parameter so that firmware and
nvram files can be loaded from the specified path.
Signed-off-by: Daniel Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reworked the debugfs functions in the driver making it easier for
other driver parts to add a debugfs entry and keeping the information
they want to expose in debugfs private, ie. not in a header.
This is accomplished by providing the function brcmf_debugfs_add_entry()
in which the caller provides a read function in which they provide the
content. The debugfs function will take care of creating the debugfs
entry and cleaning up upon removal.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The use of seq_file simplifies the debugfs code. Simpler is
better.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up used broadcom IDs, device IDs for all the
bus layers and uses consistent naming for all IDs.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes this typo.
Reported-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sta_ptr is used only in an 'if' branch in this function.
Move it to the smaller scope where it is used.
Reported-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The unit of this timeout is in seconds.
Reported-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'else if' branch never gets the chance as its condition
matches 'if' branch's.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes pending internal scan commands are delayed to give
preference to Tx traffic. 'scan_processing' flag has been
checked at the beginning of delay timer routine to know if in the
meantime scan operation has been cancelled.
There is a corner case where pending scan commands are emptied
after scan_processing flag check is passed. In this case
wrong pointer returned by list_first_entry() is passed to
list_del() which causes system hang.
This patch fixes the issue by adding list_empty() check.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in which rx_reorder_tbl_ptr is accessed
without holding spinlock at few places.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The *_bit operations expect unsigned longs.
Instead of casting the pointers, simply define various
bitmaps as unsigned long (instead of u32).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some corner cases with specific timings, we might
try dequeueing tx before we got information about
the link status (e.g. due to recovery during tx).
Instead of NULL dereference, assume all
the links in this case have low priorities.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Each 18xx chip contains only 2 real MAC addresses
usable for WLAN, forcing us to use the LAA bit
approach to obtain a third MAC address.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sending the FW a channel switch command on a disconnected
vif may result in a beacon loss event. Avoid this corner case.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All the smart config code is in place now,
so register the relevant vendor commands.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we don't have any actual limitation in the driver, so
increase it arbitrarily to 30 seconds.
The long ROC is needed for the smart config.flow.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add defintions and handling for smart config events
(SMART_CONFIG_SYNC_EVENT_ID and SMART_CONFIG_DECODE_EVENT_ID)
parse the relevant info and send it to userspace as
vendor event.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
userspace can ask to perform various smart config
actions via custom vendor commands.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These commands configures the fw to set key,
enter smart config mode, and exit it.
Add relevant hw ops as well.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The LAA bit is second bit of the MSB, not of the
third byte.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The last tx rate calculation didn't take into account
the different indices of 11a and 11g rates tables.
Add the required alignment (count only from the first
11a rate in case of 11a)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On recovery, we increase the current seq num by
WL1271_TX_SQN_POST_RECOVERY_PADDING in order to
compensate for packets we might have missed during
recovery.
It seems that some GEM APs have issues when the
gap is too big, so use a smaller padding in this case.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We want seq num (freed_pkts) to be initialized
on each new connection, but keep persistent
between recoveries/suspends.
Save the freed_pkts in the private block of the
sta struct (we already do a similar thing for
AP's stations).
However, keep the old wlvif->total_freed_pkts
in order to avoid too intrusive change.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This could be a bit confusing to see warning about lacking support for
5 GHz band if your device supports 2.4 GHz only.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Support for N-PHY rev 8 with 0x2057 rev 5 is almost ready, but we still
need to figure out how to handle rev 9 first.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialization of N-PHY radio revs 5 and 7 requires writing to 0x1.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Type of radio has a major meaning for the driver. There is quite some
code that does initialization/calibration depending on the radio rev.
Knowing radio params is quite important to provide help to users, so
print it even with debugging disabled.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The tx ring index was immediately trimmed with a
bitmask. This discarded the 0xFFFFFFFF error case
(which theoretically can happen when a device is
abruptly disconnected) and led to using an invalid
tx ring index. This could lead to memory
corruption.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It was possible for tx completion not to be
processed. In that case an old stack pointer was
left on copy engine tx ring. Next bmi exchange
would immediately pop it and use complete() on the
completion struct there causing corruption.
Make sure to wait for both tx and rx completions
properly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If firmware probing worker failed it called
device_release_driver() which synchronously called
remove() pci callback. The callback in turn waited
for the worker that called it to finish resulting
in a deadlock.
Waiting for a completion instead of a worker, like
some other drivers do, doesn't seem like the best
idea either:
Syscall Worker
probe_fw()
rmmod
dev_lock()
pci->remove()
wait_for_completion()
complete_all()
device_release_driver()
dev_lock()
[sleep]
free(ar)
dev_unlock()
[resume]
There's no guarantee that Worker upon resuming can
still access any data/code of the module.
Leaving device bound to a driver is not as harmful
as deadlocking so remove the call to
device_release_driver() while a proper solution is
figured out.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This change enables ath6kl driver to support ar6004 hw3.0. At the same time do
some fixes in firmware initialisation which applies to ar6004 hw1.3 as well.
Signed-off-by: Jessica Wu <wjessica@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some of the firmware versions support rate tables up to mcs15, add support for
that.
Signed-off-by: Jessica Wu <wjessica@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
rx flush was not implemented for htc pipe, add that now. Doesn't fix any known
issues.
Also free the skb if htc control messages get canceled.
Signed-off-by: Jessica Wu <wjessica@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The functionality defined through these flags were actually firmware features
which can change between firmware versions. To make it possible to support
different firmware versions with the same driver, convert the flags to firmware
feature flags.
For backwards compatibility support for old ar6004 firmware FW
API 3 or smaller images we forcefully set the feature bits in the driver.
Starting from FW API 5 the firmware image needs to set them.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
tmp may be used uninitialized if ath6kl_bmi_read() returns an error.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Allow to setup maximum subframes for AMSDU and AMPDU aggregation
via debugfs htt_max_amsdu_ampdu file.
Eg.
echo "2 64" > htt_max_amsdu_ampdu
will setup maximum amsdu subframes equal 2 and
maximum ampdu subframes equal to 64.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This changes
b43-phy0: Found Radio: Manuf 0x17F, Version 0x7769, Revision 4
to the
b43-phy0: Found Radio: Manuf 0x17F, Version 0x2069, Revision 4
which matches what closed source driver reports:
$ wl revinfo
radiorev 0x42069000
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows adding more revisions support, spotting lacking tables and
unifies naming schema.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The comment was not accurate, we are talking about the frames
*for* the station and not from the station.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This patch removes the setting of the ADC sampling bits in
the mvm nic configuration. This setting is not required by
the firmware, and furthermore - it interferes with the DBGC
when it is running in DRAM mode on PCIe.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Dor Shaish <dor.shaish@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The FW currently doesn't optimally support TDLS in DCM mode. Teardown
all TDLS peers when we have more than a single phy context.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The FW does not support PSM on a vif with associated TDLS peers. Disable
PSM when the first peer joins and re-enable it when the last leaves.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Use the new mac80211 callback to protect a TDLS discovery session so we
can hear the discovery-response packet.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
HW/FW constraints dictate that TDLS should only be used when a single
phy ctx is active. We also support at most 4 TDLS peers. We don't
support TDLS on a P2P vif.
Unify and move a phy-ctx counting implementation from the power-mgmt code
in order to simplify implementation.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
An AP/GO may perform the channel switch slightly before its stations.
This scenario may result in packet loss, since the transmission may start
before the client is actually on a new channel. In order to prevent
potential packet loss disable tx to all the stations when the channel
switch flow starts. Clear the disable_tx bit when a station is seen on a
target channel, or after IWL_MVM_CS_UNBLOCK_TX_TIMEOUT beacons on a new
channel. In addition call ieee80211_sta_block_awake in order to inform
mac80211 that the frames for this station should be buffered.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
According to the spec, GO/AP should perform the channel switch just
before "beacon 0". However, since the exact timing isn't defined,
it may result in a sudden GO disappearance from the channel.
Prevent potential packet loss when performing the CS by scheduling
NoA time event and executing the channel switch flow when a notification
from fw is received.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently mvm->csa_vif is protected with mvm mutex. The RCU protection
is required for "iwlwifi: mvm: Reflect GO channel switch in NoA" patch.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Call ieee80211_beacon_get_template instead of ieee80211_beacon_get and sync the
CSA counters with mac80211 after each beacon transmission.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Implement support for unbind-bind flow for the client roles. This
includes telling the firmware that we are not associated, removing
time-events, removing quotas and updating power management during the
actual switch, and redoing everything in the new channel.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Implement the switch_vif_chanctx operation with support for a
single-vif and SWAP mode. The REASSIGN mode and multi-vifs are not
supported yet.
This operation needs to implement 4 steps, namely unassign, remove,
add and assign the chanctx. In order to do this, split out these
operations into locked and non-locked parts, thus allowing us to call
them while locked.
Additionally, in order to allow us to restart the hardware when
something fails, add a boolean to the iwl_mvm_nic_restart() function
that tells whether the restart was triggered by a FW error or
something else.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
It turns out that adding the update type argument was pointless as
quota update is never called from the add_interface() callback.
Therefore, IWL_MVM_QUOTA_UPDATE_TYPE_NEW isn't actually needed and
then only a "disabled_vif" argument is needed for the upcoming CSA
work.
Remove the whole enum iwl_mvm_quota_update_type and pass the right
arguments (always NULL for disabled vif right now) to the function
in all current call sites.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Simplify the quota iterator by not passing the update type,
it only needs to know whether or not to skip an interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware currently deals with zero quota for a given
binding, but it seems odd to send that down. Make sure
that we don't do that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There are some cases where we can currently send zero quota
for a valid binding, e.g. if we update while an interface is
bound to a channel context but not yet acting as an AP.
Avoid this by reordering the checks.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In some cases (e.g. when we're doing a channel switch), we may need to
disable the quota of a vif temporarily. In order to do so, add an
argument to the iwl_mvm_update_quotas() function to tell if the passed
vif is a new one or if it should be disregarded.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
when driver takes the MAC address from the HW section and
it isn't valid - print an error.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Initialize LMAC scan command.
Fix EBS flag to be dependant on TLV flg and fix other bugs.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add new scan API that uses the same command 0x51 for both regular and
sched scan.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
These file are removed recursively anyway, so there's no
point saving them just to redundantly remove them later.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
iwl_mvm_rs_rate_init() is called multiple times to re-init
the rate scaling statistics (e.g. after some idle time).
It clears all the lq_sta sta, including some fields that
shouldn't be cleared (e.g. debugfs pointers). Fix it
by adding a new 'persistent' sub-struct, and
avoid clearing it on (re-)init.
Move the initialization of the persistent fields to
rs_alloc_sta instead.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When TxTxCo-Running is active, we can relax the constraints
on the rate control.
When RxRxCo-Running is active, we can relax the constrains
on SMPS.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
No need to send the big BT_COEX_CMD command, we have now
a much thiner command that updates only what is needed.
Adapt the code to that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
No need to send the big BT_COEX_CMD command, we have now
a much thiner command that updates only what is needed.
Adapt the code to that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
No need to send the big BT_COEX_CMD command, we have now
a much thiner command that updates only what is needed.
Adapt the code to that, and open the patch to the updates.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Start the new BT Coex implementation.
Don't react to notifications for now - only the initial
configuration is implemented. The rest will happen in next
patches.
Since coex.c now uses the new the new structures in all
functions, we need to adapt the code to compile, even if it
doesn't run yet.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
A new API is coming. This new API is not backward
compatible. So we need to keep the old commands to be able
to work with the former API.
Move all the current code into a new file: coex_legacy.
If a firmware with the new API is detected, we currently
just bail out since the implementation of the new API will
come in future patches.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In family 8000 products the MAC address in the OTP could be in either:
- WFPM address
- PCIE address
In sdio product we should read it from the WFPM, in pcie product we
should read it from the PCIe location.
This is relevant only from otp version 0xE08 and above.
While at it, fix the bytes order in version 0xE08.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This patch makes sure there're no target accesses in the add
interface flow before d0i3 exit completes.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Its content can move to the caller.
While at it, move iwl_mvm_fw_error_rxf_dump to caller.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of reading all the data in the context of the
interrupt thread, collect the data in the restart flow
before the actual restart takes place so that the device
still has all the information.
Remove iwl_mvm_fw_error_sram_dump and move its content to
iwl_mvm_fw_error_dump.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There are few places at the begining of Tx/Rx paths where
tx_info/rx_info is not correctly initialized. This patch
takes care of it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware folks seem say that this flag can make trouble.
Drop it. The advantage of CTS to self is that it slightly
reduces the cost of the protection, but make the protection
less reliable.
Cc: <stable@vger.kernel.org> [3.13+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We should always prefer to use full RTS protection. Using
CTS to self gives a meaningless improvement, but this flow
is much harder for the firmware which is likely to have
issues with it.
CC: <stable@vger.kernel.org>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This adds some cores with 0x2057 radio which will be supported soon as
well as core 40 that I missed in the earlier firmware patch.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It doesn't include any device (radio revision) specific code yet, so it
isn't really usable. As the commit says, it's just some generic code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are several exit path from the PCI probe function.
Some of them, that are taken in case of errors, forget to set the "err"
variable, that is returned by the probe function.
This can lead to the kernel thinking the probe function succeeds while it
didn't, and this in turn causes extra calls to the "remove" function.
This patch fix this problem by ensuring "err" variable is assigned to a proper
non-zero value in each exit path.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All boards supported by this driver could work using PIO or MMIO for accessing
registers.
This driver tries to access HW by using MMIO, and, if this fails for somewhat
reason, the driver tries to fall back to PIO mode.
MMIO-mode is straightforward on all boards.
PIO-mode is straightforward on rtl8180 only.
On rtl8185 and rtl8187se boards not all registers are directly available in PIO
mode (they are paged).
On rtl8185 there are two pages and it is known how to switch page.
PIO mode works, except for only one access to a register out of default page,
recently added by me in the initialization code with patch:
rtl818x_pci: Fix rtl8185 excessive IFS after CTS-to-self
This can be easily fixed to work in both cases (MMIO and PIO).
On rtl8187se, for a number of reasons, there is much more work to do to fix PIO
access.
PIO access is currently broken on rtl8187se, and it never worked.
This patch fixes the said register write for rtl8185 and makes the driver to
fail cleanly if PIO mode is attempted with rtl8187se boards.
While doing this, I converted also a couple of printk(KERN_ERR) to dev_err(), in
order to make checkpatch happy.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the driver configures mac80211 to provide two rates for each TX frame:
One initial rate and one alternate fallback rate, each one with its retry count.
HW does not support fully this: rtl8180 doesn't have support for rate scaling at
all, and rtl8185/rtl8187SE supports it in a way that does not fit with mac80211:
The HW does automatically fall back to the next lower rate, and only a lower
limit can be specified, so the HW may TX also on rates in between the two rates
specified by mac80211. Furthermore only the total TX retry count can be
specified for each packet, while the number of TX attempts before scaling rate
can be configured only globally (not per each packet).
Currently the driver sets the HW auto rate fallback mechanism to quickly scale
rate after a couple of retries, and it uses the alternate rate requested by
mac80211 as fallback limit rate (and it does this even wrongly).
The HW indeed will behave differently than what mac80211 mandates, that is
probably undesirable, and the reported TX retry count may not refer to what
mac80211 thinks, and this could fool mac80211.
This patch makes the driver to declare to mac80211 to support only one rate
configuration for each packet, and it does disable the HW auto rate fallback
mechanism, relying only on SW and letting mac80211 to do all by itself.
This should ensure correct operation and fairness respect to mac80211.
Indeed here tests with iperf do not show significant performance differences.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
HW is programmed with wrong retry count value for TX:
Mac80211 passes to driver the number of times the TX should be attempted.
The HW, instead, wants the number of time the TX should be retried if it fails
the first time (assuming we have to TX it at least one time).
This patch correct this.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rtl8187se support has been added to the rtl818x_pci driver by extracting a lot
of information from a rtl8187se Linux staging driver included in the kernel at
the time rtl8187se support was added.
The rtl818x_pci main file has a comment that advertises this.
Recently this staging driver has been removed from the kernel, but I still feel
it can be useful as "reference" code (in case of bugs, or to implement
improvements in rtl818x_pci driver).
This one-line patch adds a comment in rtl818x_pci driver to point people
searching for that "reference code" to the last kernel version still containing
it (3.14).
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Measuring time between _end_ of CTS-to-self and _end_ of datapacket (with a
prism54 board and mac80211 hacked to let the MAC timestamp stay untouched in the
radiotap header) resulted in about 300uS, while the datapacket itself should be
by far shorter (less than 100uS) and IFS should be SIFS (10uS).
This measure was confirmed whith a scope: about 250uS IFS has been seen between
the two packets.
This situation causes the CTS-to-self protection mechanism to work incorrectly
due to the NAV expiring during, or even before beginning, the packet
transmission, and it also causes the performances to be anyway reduced due to
time waste.
This problem has been seen at every packet TXed with CTS-to-self enabled on
rtl8185 board.
rtl8187se seems not affected (and rtl8180, being a 802.11b card, does not have
CTS-to-self mechaninsm).
This patch fixes this by adding a magic register write, making the board wait
for correct SIFS after CTS-to-self packet.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BSSID register was written with six byte-writes.
It seems that, similarly to what happens with MAC registers, they needs to be
written with one 16-bit and one 32-bit writes, otherwise the write does not work.
The byte write didn't work only on my rtl8185, while it worked on rtl8180 and
rtl8187se, BTW since there are probably a number of different ASIC revisions out
of there, I let the change to affect all cards.
It shouldn't hurt anyway.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
LCNXN is simply a continuation of N, e.g. code handling LCNXN revs 0 and
1 is mostly the same as for N-PHY revs 7+.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix checkpatch warning:
WARNING: kfree(NULL) is safe this check is probably not required
Cc: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes a couple of issues:
- absence of deallocation of rsi_dev->rx_usb_urb[0] in the driver;
- potential NULL pointer dereference because of lack of checks for memory
allocation success in rsi_init_usb_interface().
By the way, it makes rsi_probe() returning error code instead of 1
and fixes comments regarding returning values.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Right now sleep duration is configured as beacon interval. It should be
the multiple of beacon interval by listen period which helps to
reduce station power consumption.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Earlier the listen interval is used to decide switching between
operating and off-channels during bgscan and to improve throughput,
the listen interval is reduced to 1. After optimiztion in scan
state machine, listen period is not used for decision making and
hence reverting it back to original value.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The beacon configurations are not cached properly after the station
associates with AP. Not handling BEACON_INFO, is failing to update
dtim period and also it is causing below warning message.
WARNING: CPU: 1 PID: 0 at drivers/net/wireless/ath/ath9k/recv.c:548
ath_rx_tasklet+0xc89/0xca0 [ath9k]()
Call Trace:
[<c14669c9>] dump_stack+0x48/0x69
[<c104f1a2>] warn_slowpath_common+0x82/0xa0
[<fd38c2f9>] ? ath_rx_tasklet+0xc89/0xca0 [ath9k]
[<fd38c2f9>] ? ath_rx_tasklet+0xc89/0xca0 [ath9k]
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Treat frames that underwent a CCK or OFDM restart as frames with an invalid CRC.
Signed-off-by: Mathy Vanhoef <vanhoefm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the FIF_FCSFAIL filter flag is set, pass frames with CRC errors.
Signed-off-by: Mathy Vanhoef <vanhoefm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Why is converting time formats so desired if there are proper
interfaces for this?
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bing Zhao <bzhao@marvell.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit a82fc3b4a2bceb7c6587249cb690342eb5065979.
Thomas corrected me on that I misunderstood Johannes' comment
for net_timedelta() and the ktime_get_real() usage inside
__net_timestamp().
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixed a warning related to incorrect return type and removed an
unnecessary semi colon.
Signed-off-by: Jahnavi Meher <jahnavi.meher@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixed a potential buffer overflow in 'rsi_rates' and a sparse warning
related to difference in endianness in rsi_91x_mgmt.c.
Signed-off-by: Jahnavi Meher <jahnavi.meher@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The p54 driver uses request_firmware() twice, once for actual
firmware and then another time for an optional user overide on
EEPROM, 3826.eeprom. The custom EEPROM is optional but if not
present we'll introduce an extra lag of 60 seconds with udev
present. Annotate we don't want udev nonsense here to avoid
the lag in case its not present.
This was found with the following SmPL patch.
@ firmware_not_critical @
expression cf;
expression config_file;
expression dev;
int ret;
identifier l;
statement S;
@@
- ret = request_firmware(&cf, config_file, dev);
+ ret = request_firmware_direct(&cf, config_file, dev);
if (ret < 0) {
... when != goto l;
when != return ret;
when any
} else {
...
release_firmware(cf);
...
}
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: linux-wireless@vger.kernel.org
Cc: cocci@systeme.lip6.fr
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Acked-By: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix tx gain table index on fast channel change for AR953x.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sujith Manoharan