This makes the filename match the Kconfig symbol and the driver name.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Support two new half-duplex SPI implementation restrictions, for links
that talk to TX-only or RX-only devices. (Existing half-duplex flavors
support both transfer directions, just not at the same time.)
Move spi_async() into the spi.c core, and stop inlining it. Then make
that function perform error checks and reject messages that demand more
than the underlying controller can support.
Based on a patch from Marek Szyprowski which did this only for the
bitbanged GPIO driver.
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
tAdd adds McSPI support for OMAP4430 SDP platform. All the base addresses
are changed between OMAP1/2/3 and OMAP4. The fields of the resource
structures are filled at runtime to have McSPI support on OMAP4.
Signed-off-by: Syed Rafiuddin <rafiuddin.syed@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previous restore was lazy and only restored CHxCONF when it was needed by
a specific chip select. This could cause occasional errors on an SPI bus
where multiple chip selects are in use.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the update to the spi_bitbang driver, the transfer setup code is
being called more often, and thus is often re-doing calculations that have
been done before. The SPI layer allows our driver to add its own data to
each device so add a result cache to each device.
This should also remove the problem where we where directly setting up
registers in the setup call which meant we might overwrite the state of an
extant transfer.,
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the spi_s3c24xx driver to use dev_pm_ops to avoid the following
warning during probe:
Platform driver 's3c2410-spi' needs updating - please use dev_pm_ops
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the use of (res->end - res->start) to use resource_size() to
get the size of the resource.
Signed-off-by; Ben Dooks <ben@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver includes <asm/io.h> where it should be including <linux/io.h>
and also includes <mach/hardware.h> and <asm/dma.h> without using anything
from these.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Register pxa2xx_spi earlier so it can be used with cpufreq
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Daniel Ribeiro <drwyrm@gmail.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes it consistent with other buses (platform, i2c, vio, ...). I'm
not sure why we use the prefixes, but there must be a reason.
This was easy enough to do it, and I did it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Acked-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With this patch spi drivers can use standard spi_driver.id_table and
MODULE_DEVICE_TABLE() mechanisms to bind against the devices. Just like
we do with I2C drivers.
This is useful when a single driver supports several variants of devices
but it is not possible to detect them in run-time (like non-JEDEC chips
probing in drivers/mtd/devices/m25p80.c), and when platform_data usage is
overkill.
This patch also makes life a lot easier on OpenFirmware platforms, since
with OF we extensively use proper device IDs in modaliases.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver has been tested on i.MX1/i.MX27/i.MX35 with an AT25 type
EEPROM and on i.MX27/i.MX31 with a Freescale MC13783 PMIC.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: Andrea Paterniani <a.paterniani@swapp-eng.it>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes the PL022 driver a default choice for any RealView and
Versatile boards plus the integrator IMPD1 which all contain the PL022
PrimeCell. This will make it a default choice if and only if a user
selects SPI support for their board.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a SPI driver for the SPI controller found in the IBM/AMCC
4xx PowerPC's.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Ocker <weo@reccoware.de>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert bit shifted values into BIT format
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver is in a non working state at the moment and will be replaced
by a bitbang driver which can also handle the newer i.MX variants
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: David Brownell <david-b@pacbell.net>
Acked-by: Andrea Paterniani <a.paterniani@swapp-eng.it>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The definition of the SPI clock phase for the Motorola mode of
the PL022 driver was incorrect: the spec had been interpreted as
data being recieved on rising or falling edge of the clocks while
the correct interpretation is that data can be recieved on the
first or second edge transition, falling or rising depending on
the polarity setting.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the changes to the bitbang driver, there is the possibility we will
be called with either the speed_hz or bpw values zero. We take these to
mean that the default values (8 bits per word, or maximum bus speed).
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the clock rate calculation may round as pleased, which means
that it is possible that we will round down and end up with a faster clock
rate than intended.
Change the calculation to use DIV_ROUND_UP() to ensure that we end up with
a clock rate either the same as or lower than the user requested one.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When data is read through DMA, the last element must be read separately
through the RX register. It cannot be transferred by the DMA. For
further details see e.g. OMAP35x TRM (table 19-16).
Without the fix the driver causes extra clocks to be clocked to the bus
after DMA RX operations. This can cause interesting behaviour with some
devices.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
[aaro.koskinen@nokia.com: Simplified the patch while keeping the idea.]
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently mcspi wake-ups are not enabled. This might cause cases where
OMAP is not waking up on mcspi events.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove duplicated #include('s) in
drivers/spi/amba-pl022.c
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Bugfix to spi_bitbang infrastructure: make sure to always set transfer
parameters on the first pass through the message's per-transfer loop.
This can matter with drivers that replace the per-word or per-buffer
transfer primitives, on busses with multiple SPI devices.
Previously, this could have started messages using the settings left after
previous messages. The problem was observed when a high speed chip
(m25p80 type flash) was running very slowly because a low speed device
(avr8 microcontroller) had previously used the bus. Similar faults could
have driven the low speed device too fast, or used an unexpected word
size.
Acked-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a new spi_master.flags word listing constraints relevant to that
controller. Define the first constraint bit: a half duplex restriction.
Include that constraint in the OMAP1 MicroWire controller driver.
Have the mmc_spi host be the first customer of this flag. Its coding
relies heavily on full duplex transfers, so it must fail when the
underlying controller driver won't perform them.
(The spi_write_then_read routine could use it too: use the
temporarily-withdrawn full-duplex speedup unless this flag is set, in
which case the existing code applies. Similarly, any spi_master
implementing only SPI_3WIRE should set the flag.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add two new spi_device.mode bits to accomodate more protocol options, and
pass them through to usermode drivers:
* SPI_NO_CS ... a second 3-wire variant, where the chipselect
line is removed instead of a data line; transfers are still
full duplex.
This obviously has STRONG protocol implications since the
chipselect transitions can't be used to synchronize state
transitions with the SPI master.
* SPI_READY ... defines open drain signal that's pulled low
to pause the clock. This defines a 5-wire variant (normal
4-wire SPI plus READY) and two 4-wire variants (READY plus
each of the 3-wire flavors).
Such hardware flow control can be a big win. There are ADC
converters and flash chips that expose READY signals, but not
many host controllers support it today.
The spi_bitbang code should be changed to use SPI_NO_CS instead of its
current nonportable hack. That's a mode most hardware can easily support
(unlike SPI_READY).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: "Paulraj, Sandeep" <s-paulraj@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since we renamed the file, we might want to rename the file internals too.
Though we don't bother with changing platform driver name and platform
module alias. The stuff is legacy and hopefully we'll remove it soon.
Suggested-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver handles MPC83xx, MPC85xx and MPC86xx SPI controllers, so rename
the file for clarity.
Suggested-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes #if 0'ed code, and spi_mpc83xx->busy variable that is
used by that dead snippet only.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mpc83xx_spi_work() is quite large, with up to five indentation levels and
is quite difficult to read.
So, split the function in two parts:
1. mpc83xx_spi_work() now only traverse queued spi messages;
2. mpc83xx_spi_do_one_msg() only manages single messages.
There should be no functional changes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Checkpatch is spitting errors when seeing the rename patch, so fix the
errors prior to moving.
Following errors and warnings were fixed:
WARNING: Use #include <linux/io.h> instead of <asm/io.h>
#1027: FILE: drivers/spi/spi_mpc8xxx.c:37:
+#include <asm/io.h>
ERROR: "foo * bar" should be "foo *bar"
#1111: FILE: drivers/spi/spi_mpc8xxx.c:121:
+static inline void mpc83xx_spi_write_reg(__be32 __iomem * reg, u32 val)
ERROR: "foo * bar" should be "foo *bar"
#1116: FILE: drivers/spi/spi_mpc8xxx.c:126:
+static inline u32 mpc83xx_spi_read_reg(__be32 __iomem * reg)
ERROR: "foo * bar" should be "foo *bar"
#1125: FILE: drivers/spi/spi_mpc8xxx.c:135:
+ type * rx = mpc83xx_spi->rx; \
ERROR: "foo * bar" should be "foo *bar"
#1135: FILE: drivers/spi/spi_mpc8xxx.c:145:
+ const type * tx = mpc83xx_spi->tx; \
WARNING: suspect code indent for conditional statements (16, 25)
#1504: FILE: drivers/spi/spi_mpc8xxx.c:514:
+ while (((event =
[...]
+ cpu_relax();
Following warnings were left over, since fixing them will hurt the
readability. We'd better fix them by lowering the indentation level by
splitting mpc83xx_spi_work function into two parts.
WARNING: line over 80 characters
#1371: FILE: drivers/spi/spi_mpc8xxx.c:381:
+ status = mpc83xx_spi_setup_transfer(spi, t);
WARNING: line over 80 characters
#1392: FILE: drivers/spi/spi_mpc8xxx.c:402:
+ mpc83xx_spi_chipselect(spi, BITBANG_CS_INACTIVE);
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is needed for some underlaying GPIO controllers that may be a bit
slow, or if chip-select signal need some time to stabilize.
For what it's worth, we already have the similar delay for chip-select
de-assertion case.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a platform is running at high frequencies it's not always possible to
scale-down a frequency to a requested value, and using mmc_spi driver this
leads to the following printk flood during card polling:
...
mmc_spi spi32766.0: Requested speed is too low: 400000 Hz. Will use
520828 Hz instead.
mmc_spi spi32766.0: Requested speed is too low: 400000 Hz. Will use
520828 Hz instead.
...
Fix this by using WARN_ONCE(), it's better than the flood, and also better
than turning dev_err() into dev_dbg(), since we actually want to warn that
some things may not work correctly.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With this patch we'll able to select spi_mpc83xx driver on the MPC86xx
platforms. Let the driver depend on FSL_SOC, so we don't have to worry
about Kconfig anymore.
Also remove the "experimental" dependency, the driver has been tested to
work on a various hardware, and surely not experimental anymore.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Buffer needs not be dma-safe, not rx data length.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit a7bb3909b3 ("spi: pxa2xx_spi:
introduce chipselect GPIO to simplify the common cases") introduces
chipselect GPIO, and configures the CS polarity using SPI_CS_HIGH
spi->mode flag. Add SPI_CS_HIGH to the allowed modes.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mpc52xx_psc_spi driver is the last user of the legacy activate_cs and
deactivate_cs callbacks, so convert the driver to the cs_control hook and
remove the legacy callbacks from fsl_spi_platform_data struct.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move some common spi_setup() error checks into the SPI framework from the
spi_master controller drivers:
- Add a new "mode_bits" field to spi_master
- Use that in spi_setup to validate the spi->mode value being
requested. Setting this new field is now mandatory for any
controller supporting more than vanilla SPI_MODE_0.
- Update all spi_master drivers to:
* Initialize that field
* Remove current spi_setup() checks using that value.
This is a net minor code shrink.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Start moving some spi_setup() functionality into the SPI core from the
various spi_master controller drivers:
- Make that function stop being an inline;
- Move two common idioms from drivers into that new function:
* Default bits_per_word to 8 if that field isn't set
* Issue a standardized dev_dbg() message
This is a net minor source code shrink, and supports enhancments found in
some follow-up patches.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bfin_spi_flush() returns limit, which reaches -1 upon timeout. but in
function bfin_spi_pump_transfers() it is compared with 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* akpm: (182 commits)
fbdev: bf54x-lq043fb: use kzalloc over kmalloc/memset
fbdev: *bfin*: fix __dev{init,exit} markings
fbdev: *bfin*: drop unnecessary calls to memset
fbdev: bfin-t350mcqb-fb: drop unused local variables
fbdev: blackfin has __raw I/O accessors, so use them in fb.h
fbdev: s1d13xxxfb: add accelerated bitblt functions
tcx: use standard fields for framebuffer physical address and length
fbdev: add support for handoff from firmware to hw framebuffers
intelfb: fix a bug when changing video timing
fbdev: use framebuffer_release() for freeing fb_info structures
radeon: P2G2CLK_ALWAYS_ONb tested twice, should 2nd be P2G2CLK_DAC_ALWAYS_ONb?
s3c-fb: CPUFREQ frequency scaling support
s3c-fb: fix resource releasing on error during probing
carminefb: fix possible access beyond end of carmine_modedb[]
acornfb: remove fb_mmap function
mb862xxfb: use CONFIG_OF instead of CONFIG_PPC_OF
mb862xxfb: restrict compliation of platform driver to PPC
Samsung SoC Framebuffer driver: add Alpha Channel support
atmel-lcdc: fix pixclock upper bound detection
offb: use framebuffer_alloc() to allocate fb_info struct
...
Manually fix up conflicts due to kmemcheck in mm/slab.c
Do not take the size of a pointer to determine the size of the pointed-to
type.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (27 commits)
Blackfin: hook up new rt_tgsigqueueinfo syscall
Blackfin: improve CLKIN_HZ config default
Blackfin: initial support for ftrace grapher
Blackfin: initial support for ftrace
Blackfin: enable support for LOCKDEP
Blackfin: add preliminary support for STACKTRACE
Blackfin: move custom sections into sections.h
Blackfin: punt unused/wrong mutex-dec.h
Blackfin: add support for irqflags
Blackfin: add support for bzip2/lzma compressed kernel images
Blackfin: convert Kconfig style to def_bool
Blackfin: bf548-ezkit: update smsc911x resources
Blackfin: update aedos-ipipe code to upstream 1.10-00
Blackfin: bf537-stamp: update ADP5520 resources
Blackfin: bf518f-ezbrd: fix SPI CS for SPI flash
Blackfin: define SPI IRQ in board resources
Blackfin: do not configure the UART early if on wrong processor
Blackfin: fix deadlock in SMP IPI handler
Blackfin: fix flag storage for irq funcs
Blackfin: push down exception oops checking
...
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits)
MAINTAINERS: EB110ATX is not ebsa110
MAINTAINERS: update Eric Miao's email address and status
fb: add support of LCD display controller on pxa168/910 (base layer)
[ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN
[ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines
[ARM] 5544/1: Trust PrimeCell resource sizes
[ARM] pxa/sharpsl_pm: cleanup of gpio-related code.
[ARM] pxa/sharpsl_pm: drop set_irq_type calls
[ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one
[ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific
[ARM] sa1100: remove unused collie_pm.c
[ARM] pxa: fix the conflicting non-static declarations of global_gpios[]
[ARM] 5550/1: Add default configure file for w90p910 platform
[ARM] 5549/1: Add clock api for w90p910 platform.
[ARM] 5548/1: Add gpio api for w90p910 platform
[ARM] 5551/1: Add multi-function pin api for w90p910 platform.
[ARM] Make ARM_VIC_NR depend on ARM_VIC
[ARM] 5546/1: ARM PL022 SSP/SPI driver v3
ARM: OMAP4: SMP: Update defconfig for OMAP4430
ARM: OMAP4: SMP: Enable SMP support for OMAP4430
...
This adds a driver for the ARM PL022 PrimeCell SSP/SPI
driver found in the U300 platforms as well as in some
ARM reference hardware, and in a modified version on the
Nomadik board.
Reviewed-by: Alessandro Rubini <rubini-list@gnudd.com>
Reviewed-by: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move all the gpio functions out of <mach/hardware.h> as
this file is for defining the generic IO base addresses
for the kernel IO calls.
Make a new header <mach/gpio-fns.h> to take this and
include it via the chain from <linux/gpio.h> which is
what most of these files should be using (and will be
changed as soon as possible).
Note, this does make minor changes to some drivers but
should not mess up any pending merges.
CC: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
setup() may fail before ctldata is set, causing a kernel panic on
cleanup().
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
arch-imx is superseeded by the MXC architecture support.
This patch removes arch-imx from the build system.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
On line 944 the return value of flush() is considered as a boolean,
but limit reaches -1 upon timeout which evaluates to true.
On 540, 594, 720 the same occurs for wait_ssp_rx_stall()
On 536 the same occurs for wait_dma_channel_stop()
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If DMA is enabled, any spi_sync call after suspend/resume would block
forever, because DRCMR is lost on suspend. This patch restores DRCMR to
the same values set by probe.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "simplify spi_write_then_read()" patch included two regressions from
the 2.6.27 behaviors:
- The data it wrote out during the (full duplex) read side
of the transfer was not zeroed.
- It fails completely on half duplex hardware, such as
Microwire and most "3-wire" SPI variants.
So, revert that patch. A revised version should be submitted at some
point, which can get the speedup on standard hardware (full duplex)
without breaking on less-capable half-duplex stuff.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <stable@kernel.org> [2.6.28.x, 2.6.29.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most SPI peripherals use GPIOs as their chip selects, introduce .gpio_cs
for this.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With a postfix decrement limit will reach -1 rather than 0, so the warning
will not be issued.
Also, add a cpu_relax() into the busy-wait loop.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Mariusz Ceier <mceier@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. Rewrite of the non-dma data transfer functions to use only ONE mode
of TIMOD (TIMOD=0x1). With TIMOD=0, it was not possible to set the TX
bit pattern. So the TDBR = 0xFFFF inside the read calls won't work.
2. Clear SPI_RDBR before reading and before duplex transfer.
Otherwise the garbage data in RDBR will get read. Since mmc_spi uses a
lot of duplex transfers, this is the main cause of mmc_spi failure.
3. Poll RXS for transfer completion. Polling SPIF or TXS cannot
guarantee transfer completion. This may interrupt a transfer before it
is finished. Also this may leave garbage data in buffer and affect
next transfer.
[Yi Li <yi.li@analog.com>: add a field "u16 idle_tx_val" in "struct
bfin5xx_spi_chip" to specify the value to transmit if no TX value
is supplied.]
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for GPIO controlled SPI Chip Selects. To make use of this
feature, set chip_select = 0 and add a proper cs_gpio to your
controller_data.
struct spi_board_info
.chip_select = 0
struct bfin5xx_spi_chip
.cs_gpio = GPIO_P###
There are various SPI devices that require SPI MODE_0, and need to have
the Chip Selects asserted during the entire transfer. Consider using
SPI_MODE_3 (SPI_CPHA | SPI_CPOL) if your device allows it.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do this because when things crash, we get simple names like "setup" and
"start_queue" which is pretty difficult to trace back to the real thing:
the spi driver
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to comments in linux/spi/spi.h:
* All SPI transfers start with the relevant chipselect active. Normally
* it stays selected until after the last transfer in a message. Drivers
* can affect the chipselect signal using cs_change.
*
* (i) If the transfer isn't the last one in the message, this flag is
* used to make the chipselect briefly go inactive in the middle of the
* message. Toggling chipselect in this way may be needed to terminate
* a chip command, letting a single spi_message perform all of group of
* chip transactions together.
*
* (ii) When the transfer is the last one in the message, the chip may
* stay selected until the next transfer. On multi-device SPI busses
* with nothing blocking messages going to other devices, this is just
* a performance hint; starting a message to another device deselects
* this one. But in other cases, this can be used to ensure correctness.
* Some devices need protocol transactions to be built from a series of
* spi_message submissions, where the content of one message is determined
* by the results of previous messages and where the whole transaction
* ends when the chipselect goes intactive.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This bug can be observed when two SPI devices are sharing the spi bus: One
device is set as SPI CS 7, another one is using SPI CS 4.
In spi_bfin5xx.c: cs_active(), cs_deactive() are used to control SPI_FLG
register. From the debug bellow:
cs_active: flag: 0x7f91, chip->flag: 0x7f80, cs: 7
cs_active: flag: 0xef91, chip->flag: 0xef10, cs: 4
When device A (cs_7) activate CS 7, SPI_FLG is set as 0x7f91 (however,
SPI_FLG should be set as 0x7f80, or 0x6f91 if in broadcast mode).
Due to some HW bug (very possibly), if SPI_FLG is set as 0x7f91, SPISSEL7
is asserted, however SPISSEL4 will be asserted too (I can see this using
the scope). This is unreasonable according to HRM.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Without this change, SPI DMA is not reliably under stress tests.
Obiviously it's a hardware issue which is not addressed by any document.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "while" endless loop will cause the system hang if hardware error, so
we add timeout control to make the system alive.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When using a BF533-STAMP here with a W25X10 SPI flash. It works fine when
enable_dma is disabled, but doesn't work at all when turning DMA on. We
get just 0xff bytes back when trying to read the device.
Change the code around so that it programs the SPI first and then enables
DMA, it seems to work a lot better ...
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
use the properl BIT_CTL_... defines rather than the internal driv er
CFG_SPI_... defines
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We only need to check SPI error when DMA failes, cause that is the DMA IRQ
handling routine.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Because of DMA hardware issue, we were trying to use software workaround.
This patch add some useful debug messages to help us debugging the DMA
code.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Blackfin's related DMA callback API doesn't need void * cast, so drop it.
And this driver is for all Blackfin processors not only for BF53x, we
update the DMA request label for more meaningful information.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For DMA TX/RX operation in pump_transfers, DMA contriguration code in TX
and RX paths are almost the same. This patch unify the duplicated DMA
code to make it more readable.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the SPI bus registers a receive overflow error, pass the result back up
to the higher levels.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use len_in_bytes when we care about the number of bytes transferred rather
than the number of spi transactions. (this value will be the same for
8bit transfers, but not any other sizes)
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We already moved bfin_addr_dcachable() and friends into the cacheflush
header where it belongs, so don't need to include <asm/cplbinit.h> here.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix erroneous SPI Clock divisor calculation. Make sure SPI_BAUD is always
>= 2. Writing a value of 0 or 1 to the SPI_BAUD register disables the
serial clock.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Flush or invalidate caches before doing DMA transfer, if needed.
[Mike Frysinger <vapier.adi@gmail.com>: add comment to address the
issue "Full duplex only works for non-DMA transfers".]
Signed-off-by: Vitja Makarov <vitja.makarov@gmail.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change spi-gpio so that it is possible to drive SPI communications over
GPIO without the need for a chipselect signal.
This is useful in very small setups where there's only one slave device
on the bus.
This patch does not affect existing setups.
I use this for a tiny communication channel between an embedded device and
a microcontroller. There are not enough GPIOs available for chipselect
and it's not needed anyway in this case.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement full support for OF SPI bindings. Now the driver can manage its
own chip selects without any help from the board files and/or fsl_soc
constructors.
The "legacy" code is well isolated and could be removed as time goes by.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The main purpose of this patch is to pass 'struct spi_device' to the chip
select handling routines. This is needed so that we could implement
full-fledged OpenFirmware support for this driver.
While at it, also:
- Replace two {de,activate}_cs routines by single cs_contol().
- Don't duplicate platform data callbacks in mpc83xx_spi struct.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The patch fixes following sparse warnings:
CHECK spi_mpc83xx.c
spi_mpc83xx.c:145:1: warning: symbol 'mpc83xx_spi_rx_buf_u8' was not declared. Should it be static?
spi_mpc83xx.c:146:1: warning: symbol 'mpc83xx_spi_rx_buf_u16' was not declared. Should it be static?
spi_mpc83xx.c:147:1: warning: symbol 'mpc83xx_spi_rx_buf_u32' was not declared. Should it be static?
spi_mpc83xx.c:148:1: warning: symbol 'mpc83xx_spi_tx_buf_u8' was not declared. Should it be static?
spi_mpc83xx.c:149:1: warning: symbol 'mpc83xx_spi_tx_buf_u16' was not declared. Should it be static?
spi_mpc83xx.c:150:1: warning: symbol 'mpc83xx_spi_tx_buf_u32' was not declared. Should it be static?
spi_mpc83xx.c:175:32: warning: incorrect type in initializer (different address spaces)
spi_mpc83xx.c:175:32: expected void *tmp_ptr
spi_mpc83xx.c:175:32: got unsigned int [noderef] <asn:2>*<noident>
spi_mpc83xx.c:183:26: warning: incorrect type in argument 1 (different address spaces)
spi_mpc83xx.c:183:26: expected unsigned int [noderef] [usertype] <asn:2>*reg
spi_mpc83xx.c:183:26: got void *tmp_ptr
spi_mpc83xx.c:184:26: warning: incorrect type in argument 1 (different address spaces)
spi_mpc83xx.c:184:26: expected unsigned int [noderef] [usertype] <asn:2>*reg
spi_mpc83xx.c:184:26: got void *tmp_ptr
spi_mpc83xx.c:287:31: warning: incorrect type in initializer (different address spaces)
spi_mpc83xx.c:287:31: expected void *tmp_ptr
spi_mpc83xx.c:287:31: got unsigned int [noderef] <asn:2>*<noident>
spi_mpc83xx.c:295:25: warning: incorrect type in argument 1 (different address spaces)
spi_mpc83xx.c:295:25: expected unsigned int [noderef] [usertype] <asn:2>*reg
spi_mpc83xx.c:295:25: got void *tmp_ptr
spi_mpc83xx.c:296:25: warning: incorrect type in argument 1 (different address spaces)
spi_mpc83xx.c:296:25: expected unsigned int [noderef] [usertype] <asn:2>*reg
spi_mpc83xx.c:296:25: got void *tmp_ptr
spi_mpc83xx.c:486:13: warning: symbol 'mpc83xx_spi_irq' was not declared. Should it be static?
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver was not releasing memory when it was removed or
when there was a failure during probe. This fixes it.
Signed-off-by: John Linn <john.linn@xilinx.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
1. Driver code where pxa_request_dma() is called will most likely
reference DMA registers as well, and it is really unnecessary
to include pxa-regs.h just for this. Move the definitions into
<mach/dma.h> and make relevant drivers include it instead of
<mach/pxa-regs.h>.
2. Introduce DMAC_REGS_VIRT as the virtual address base for these
DMA registers. This allows later processors to re-use the same
IP while registers may start at different I/O address.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
gpio_get_value() returns 0 or nonzero, but getmiso() expects 0 or 1.
Sanitize the value to a 0/1 boolean.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... which now means no driver requests the "armxor_ck" clock directly.
Also, fix the error handling for clk_get(), ensuring that we propagate
the error returned from clk_get().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For some reason I have to slowdown clock to touchscreen device.
In atmel_spi_setup() there is comment that max_speed_hz == 0 means as slow
as possible and divider is set to maximum value. But in
atmel_spi_transfer() function is check against not zero max_speed_hz with
EINVAL returned.
Probably driver should setup divider for each transfer based on
transfer->speed_hz value, but I think that would be not necessary overhead
as all used devices have constant clock.
Below patch works fine for me.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a byteswap bug in the LM70 temperature sensor driver,
which was previously covered up by a converse bug in the driver
for the LM70EVAL-LLP board (which is also fixed).
Other fixes: doc updates, remove an annoying msleep(), and improve
three-wire protocol handling.
Signed-off-by: Kaiwan N Billimoria <kaiwan@designergraphix.com>
[ dbrownell@users.sourceforge.net: doc and whitespace tweaks ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
In each case, if the NULL test is necessary, then the dereference should be
moved below the NULL test.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the spi_s3c2410 driver to use the generic gpio calls that are now
available.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This solves several issues:
* It fixes the wrong idle clock polarity issue in a cleaner and less
expensive way.
* It handles the AT32AP7000 errata "SPI Chip Select 0 BITS field
overrides other Chip Selects". Other chips, e.g. AT91SAM9261, have
similar issues.
Currently, the AT91RM9200 code path is left alone. But it might be
interesting to try the same technique on RM9200 using a different CSR
register.
[dbrownell@users.sourceforge.net: restore debug message for activation]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, we have a flag called "new_1" which is basically equivalent
to cpu_is_at91rm9200(). The latter is also called directly a few places.
Clean up this mess by introducing a atmel_spi_v2() function for
determining the controller version, and move all version dependent code
over to use it. This allows us to remove the new_1 flag.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Generalize the old at91rm9200 "bootstrap" bitbanging SPI master driver as
"spi_gpio", so it works with arbitrary GPIOs and can be configured through
platform_data. Such SPI masters support:
- any number of bus instances (bus_num is the platform_device.id)
- any number of chipselects (one GPIO per spi_device)
- all four SPI_MODE values, and SPI_CS_HIGH
- i/o word sizes from 1 to 32 bits;
- devices configured as with any other spi_master controller
When configured using platform_data, this provides relatively low clock
rates. On platforms that support inlined GPIO calls, significantly
improved transfer speeds are also possible with a semi-custom driver.
(It's still painful when accessing flash memory, but less so.)
Sanity checked by using this version to replace both native controllers on
a board with six different SPI slaves, relying on three different
SPI_MODE_* values and both SPI_CS_HIGH settings for correct operation.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Magnus Damm <damm@igel.co.jp>
Tested-by: Magnus Damm <damm@igel.co.jp>
Cc: Torgil Svensson <torgil.svensson@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The spi master driver must have num_chipselect set to allow the bus to
initialise. Pass this through the platform data.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The spidev_to_sg() call in spi_s3c24xx_gpio.c was using the wrong method
to convert the spi device into the private data for the driver. Fix this
by using spi_master_get_devdata.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix unsafe order in dma mapping operation: always flush data from the
cache *BEFORE* invalidating it, to allow full duplex transfers where the
same buffer may be used for both writes and reads. Tested with mmc-spi.
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to the manual the "tdfOnExit" flag must be set on the last byte
we want to send. The PSC controller holds SS low until the flag is set.
However, the flag was set always on the last byte of the FIFO,
independently if it is the last byte of the transfer. This generates
spurious toggling of the SS signals that breaks the protocol of some
peripherals. Fix.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When ISA_DMA_API is unset, we're not implementing the ISA DMA API,
so there's no point in publishing the prototypes via asm/dma.h, nor
including the machine dependent parts of that API.
This allows us to remove a lot of mach/dma.h files which don't contain
any useful code. Unfortunately though, some platforms put their own
private non-ISA definitions into mach/dma.h, so we leave these behind
and fix the appropriate #include statments.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix unsafe order in dma mapping operation: always flush data from the
cache *BEFORE* invalidating it, to allow full duplex transfers where the
same buffer may be used for both writes and reads.
Signed-off-by: Andrea Paterniani <a.paterniani@swapp-eng.it>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes a data corruption bug in pxa2xx_spi.c when operating in full duplex
mode with DMA and using buffers that overlap.
SPI transmit and receive buffers are allowed to be the same or to overlap.
However, this driver fails if such overlap is attempted in DMA mode
because it maps the rx and tx buffers in the wrong order. By mapping
DMA_FROM_DEVICE (read) before DMA_TO_DEVICE (write), it invalidates the
cache before flushing it, thus discarding data which should have been
transmitted.
The patch corrects the order of mapping. This bug exists in all versions
of pxa2xx_spi.c; similar bugs are in the drivers for two other SPI
controllers (au1500, imx).
A version of this patch has been tested on kernel 2.6.20 using
verification of loopback data with: random transfer length, random
bits-per-word, random positive offsets (both larger and smaller than
transfer length) between the start of the rx and tx buffers, and varying
clock rates.
Signed-off-by: Ned Forrester <nforrester@whoi.edu>
Cc: Vernon Sauder <vernoninhand@gmail.com>
Cc: J. Scott Merritt <merrij3@rpi.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <stable@kernel.org> [2.6.27.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We're working with an AT91SAM9263 Rev B in our design and I experienced
some inconsistency in spi-based touchscreen usage between our board and
the Atmel evaluation kit we have that runs on a Rev A chip.
The data was apparently delayed by 1 byte and got ridiculous data out of
the touchscreen driver, very strange. As everything looked normal in
the spi, touchscreen and dma logs, I contacted the Atmel support and
they triggered me on a new HW bug that appeared in the Rev B SPI
controller.
The problem is that the SPI controller on the Rev B needs that the
software reset is performed two times so that it's performed correctly.
Applying the patch below solves the issue on my Rev B board. I've tested
it as well on my Rev A evaluation kit and it has apparently no unwanted
side effect, things continue to work as expected.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move plat/regs-spi.h to arch/arm/plat-s3c/include/plat ready
ready to clean out old include directories.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (46 commits)
UIO: Fix mapping of logical and virtual memory
UIO: add automata sercos3 pci card support
UIO: Change driver name of uio_pdrv
UIO: Add alignment warnings for uio-mem
Driver core: add bus_sort_breadthfirst() function
NET: convert the phy_device file to use bus_find_device_by_name
kobject: Cleanup kobject_rename and !CONFIG_SYSFS
kobject: Fix kobject_rename and !CONFIG_SYSFS
sysfs: Make dir and name args to sysfs_notify() const
platform: add new device registration helper
sysfs: use ilookup5() instead of ilookup5_nowait()
PNP: create device attributes via default device attributes
Driver core: make bus_find_device_by_name() more robust
usb: turn dev_warn+WARN_ON combos into dev_WARN
debug: use dev_WARN() rather than WARN_ON() in device_pm_add()
debug: Introduce a dev_WARN() function
sysfs: fix deadlock
device model: Do a quickcheck for driver binding before doing an expensive check
Driver core: Fix cleanup in device_create_vargs().
Driver core: Clarify device cleanup.
...
Make the SPI external GPIO expander drivers register themselves at
subsys_initcall() time when they're statically linked, and make the SPI
core do its driver model initialization earlier so that's safe.
SOC-integrated GPIOs are available starting very early -- often before
initcalls start to run, or earily in arch_initcall() at latest -- so this
improves consistency, letting more subsystems rely on GPIOs being usable
by their own subsys_initcall() code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support to orion_spi for the 88F6183 ARM SoC by adding code to work
around a 6183-specific erratum.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the chip info structure data optional by providing reasonable
defaults. Improve corresponding documentation, and highlight the drawback
of not providing explicit chipselect control.
DMA can determine appropriate dma_burst_size and thresholds automatically
so use DMA even if dma_burst_size is not specified.
Signed-off-by: Vernon Sauder <VernonInHand@gmail.com>
Reviewed-by: Ned Forrester <nforrester@whoi.edu>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minor fixes: remove redundant local variable initialization, fix "can not"
to what I _think_ is a preferred spelling, output IRQ number if requesting
it failed.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a pin configuration callback for the s3c24xx SPI driver, as there are
several options depending on the channel and the chip in use.
This is needed as the controller may not have been setup by the initial
bootloader and the fact that the SPI controller gets reset over
suspend/resume into slave mode but the GPIO function registers do not.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Modify spi_write_then_read() to use one transfer. This speeds up all
callers, and is a minor code shrink.
Signed-off-by: Vernon Sauder <Vernon.Sauder@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that arch/ppc is gone we don't need CONFIG_PPC_MERGE anymore
remove the dead code associated with !CONFIG_PPC_MERGE.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The register definitions have been changed for the mpc5200 PSC ports
to cover some of the changes in the mpc5200b. One change is that the
ccr register is now a u32 instead of a u16. However, for the purposes
of this driver we want to continue to use 16 bit access to avoid
changing the existing (working) behaviour.
This patch allows the driver to continue to do 16 bit accesses without
the compiler complaining about it.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Accept zero (the default!) as a per-transfer clock speed override.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a build error in the pxa2xx-spi driver,
introduced by commit 7e96445533
("pxa2xx_spi: dma bugfixes")
CC drivers/spi/pxa2xx_spi.o
drivers/spi/pxa2xx_spi.c: In function 'map_dma_buffers':
drivers/spi/pxa2xx_spi.c:331: error: invalid operands to binary &
drivers/spi/pxa2xx_spi.c:331: error: invalid operands to binary &
drivers/spi/pxa2xx_spi.c: In function 'pump_transfers':
drivers/spi/pxa2xx_spi.c:897: warning: format '%lu' expects type 'long unsigned int', but argument 4 has type 'unsigned int'
[dbrownell@users.sourceforge.net: fix warning too ]
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the section mismatch warning generated by the incorrect naming of
s3c24xx_spidrv which should be s3c24xx_spi_driver:
WARNING: drivers/spi/spi_s3c24xx.o(.data+0x4):
Section mismatch in reference from the variable s3c24xx_spidrv
to the (unknown reference) .exit.text:(unknown)
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes two DMA bugs in the pxa2xx_spi driver. The first bug is in all
versions of this driver; the second was introduced in the 2.6.20 kernel,
and prevents using the driver with chips like m25p16 flash (which can
issue large DMA reads).
1. Zero length transfers are permitted for use to insert timing,
but pxa2xx_spi.c will fail if this is requested in DMA mode.
Fixed by using programmed I/O (PIO) mode for such transfers.
2. Transfers larger than 8191 are not permitted in DMA mode. A
test for length rejects all large transfers regardless of DMA
or PIO mode. Worked around by rejecting only large transfers
with DMA mapped buffers, and forcing all other transfers
larger than 8191 to use PIO mode. A rate limited warning is
issued for DMA transfers forced to PIO mode.
This patch should apply to all kernels back to and including 2.6.20;
it was test patched against 2.6.20. An additional patch would be
required for older kernels, but those versions are very buggy anyway.
Signed-off-by: Ned Forrester <nforrester@whoi.edu>
Cc: Vernon Sauder <vernoninhand@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes several chipselect bugs in the pxa2xx_spi driver. These bugs are in
all versions of this driver and prevent using it with chips like m25p16
flash.
1. The spi_transfer.cs_change flag is handled too early:
before spi_transfer.delay_usecs applies, thus making the
delay ineffective at holding chip select.
2. spi_transfer.delay_usecs is ignored on the last transfer
of a message (likewise not holding chipselect long enough).
3. If spi_transfer.cs_change is set on the last transfer, the
chip select is always disabled, instead of the intended
meaning: optionally holding chip select enabled for the
next message.
Those first three bugs were fixed with a relocation of delays
and chip select de-assertions.
4. If a message has the cs_change flag set on the last transfer,
and had the chip select stayed enabled as requested (see 3,
above), it would not have been disabled if the next message is
for a different chip. Fixed by dropping chip select regardless
of cs_change at end of a message, if there is no next message
or if the next message is for a different chip.
This patch should apply to all kernels back to and including 2.6.20;
it was test patched against 2.6.20. An additional patch would be
required for older kernels, but those versions are very buggy anyway.
Signed-off-by: Ned Forrester <nforrester@whoi.edu>
Cc: Vernon Sauder <vernoninhand@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Error out on transfer length != multiple of bytes per word with -EINVAL.
Fixes a buffer overrun crash if length < bytes per word.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit a61f5345 (spi_mpc83xx clockrate fixes) broke clockrate calculation
for low speeds. SPMODE_DIV16 should be set if the divider is higher than
64, not only if the divider gets clipped to 1024.
Furthermore, the clipping check was off by a factor 16 as well.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When reviewing a recent patch I noticed a potential trouble spot in the
registration of new SPI devices. The SPI master driver is told to set
the device up before adding it to the driver model, so that it's always
properly set up when probe() is called. (This is important, because in
the case of inverted chipselects, this device can make the bus misbehave
until it's properly deselected. It's got to be set up even if no driver
binds to the device.)
The trouble spot is that it doesn't first verify that no other device
has been added using that chipselect. If such a device has been added,
its configuration gets trashed. (Fortunately this has not been a common
error!)
The fix here adds an explicit check, and a mutex to protect the relevant
critical region.
[akpm@linux-foundation.org: make the lock local to spi_add_device()]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds an SPI driver for the SPI controller found in various Marvell
Orion ARM SoCs. It currently supports only one slave, which must use SPI
mode 0.
[dbrownell@users.sourceforge.net: cleanups, meet specs, pass "sparse"]
Signed-off-by: Shadi Ammouri <shadi@marvell.com>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For some time my at91sam9260 board with JFFS2 on serial flash (m25p80)
would hang when accessing the serial flash and SPI bus. Slowing the SPI
clock down to 9 MHz reduced the occurrence of the hang from "always"
during boot to a nuisance level that allowed other SW development to
continue. Finally had to address this issue when an application stresses
the I/O to always cause a hang.
Hang seems to be caused by a missed SPI interrupt, so that the task ends
up waiting forever after calling spi_sync(). The fix has 2 parts. First
is to halt the DMA engine before the "current" PDC registers are loaded.
This ensures that the "next" registers are loaded before the DMA operation
takes off. The second part of the fix is a kludge that adds a
"completion" interrupt in case the ENDRX interrupt for the last segment of
the DMA chaining operation was missed.
The patch allows the SPI clock for the serial flash to be increased from 9
MHz to 15 MHz (or more?). No hangs or SPI overruns were encountered.
Haavard: while this patch does indeed improve things, I still see overruns
and CRC errors on my NGW100 board when running the DataFlash at 10 MHz.
However, I think some improvement is better than nothing, so I'm passing
this on for inclusion in 2.6.27.
Signed-off-by: Gerard Kam <gerardk5@verizon.net>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a bug in the spi_s3c24xx driver where it does not reset the registers
of the hardware when resuming from suspend (this block has been reset over
suspend).
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The original "Pass the bus number we expect the S3C24XX SPI driver to
attach to via the platform data." [1] patch was mis-sent, and missed two
important parts of the diff, which was to actually set the bus_num field
and add the relevant field to the platform data.
The previous commit 50f426b55d promised to
add a bus_num field, but failed to include the two hunks that added this
field to include/asm-arm/arch-s3c2410/spi.h and then pass it to the spi
core when creating the new master field in drivers/spi/spi_s3c24xx.c.
[1] git commit 50f426b55d
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The block transfer routine in the mpc52xx psc spi driver misinterpret
the datasheet. According to the processor datasheet the chipselect is
held as long as the EOF is not written.
Theoretically blocks of any sizes can be transferred in this way. The
old routine however writes an EOF after every word, which has the size
of size_of_word. This makes the transfer slow.
Also fixed some duplicate code.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <stable@kernel.org> [2.6.25.x, 2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add per-device dma_mapping_ops support for CONFIG_X86_64 as POWER
architecture does:
This enables us to cleanly fix the Calgary IOMMU issue that some devices
are not behind the IOMMU (http://lkml.org/lkml/2008/5/8/423).
I think that per-device dma_mapping_ops support would be also helpful for
KVM people to support PCI passthrough but Andi thinks that this makes it
difficult to support the PCI passthrough (see the above thread). So I
CC'ed this to KVM camp. Comments are appreciated.
A pointer to dma_mapping_ops to struct dev_archdata is added. If the
pointer is non NULL, DMA operations in asm/dma-mapping.h use it. If it's
NULL, the system-wide dma_ops pointer is used as before.
If it's useful for KVM people, I plan to implement a mechanism to register
a hook called when a new pci (or dma capable) device is created (it works
with hot plugging). It enables IOMMUs to set up an appropriate
dma_mapping_ops per device.
The major obstacle is that dma_mapping_error doesn't take a pointer to the
device unlike other DMA operations. So x86 can't have dma_mapping_ops per
device. Note all the POWER IOMMUs use the same dma_mapping_error function
so this is not a problem for POWER but x86 IOMMUs use different
dma_mapping_error functions.
The first patch adds the device argument to dma_mapping_error. The patch
is trivial but large since it touches lots of drivers and dma-mapping.h in
all the architecture.
This patch:
dma_mapping_error() doesn't take a pointer to the device unlike other DMA
operations. So we can't have dma_mapping_ops per device.
Note that POWER already has dma_mapping_ops per device but all the POWER
IOMMUs use the same dma_mapping_error function. x86 IOMMUs use device
argument.
[akpm@linux-foundation.org: fix sge]
[akpm@linux-foundation.org: fix svc_rdma]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix bnx2x]
[akpm@linux-foundation.org: fix s2io]
[akpm@linux-foundation.org: fix pasemi_mac]
[akpm@linux-foundation.org: fix sdhci]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix sparc]
[akpm@linux-foundation.org: fix ibmvscsi]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
spi_new_device() allocates and registers an spi device all in one swoop.
If the driver needs to add extra data to the spi_device before it is
registered, then this causes problems. This is needed for OF device
tree support so that the SPI device tree helper can add a pointer to
the device node after the device is allocated, but before the device
is registered. OF aware SPI devices can then retrieve data out of the
device node to populate a platform data structure.
This patch splits the allocation and registration portions of code out
of spi_new_device() and creates two new functions; spi_alloc_device()
and spi_register_device(). spi_new_device() is modified to use the new
functions for allocation and registration. None of the existing users
of spi_new_device() should be affected by this change.
Drivers using the new API can forego the use of spi_board_info
structure to describe the device layout and populate data into the
spi_device structure directly.
This change is in preparation for adding an OF device tree parser to
generate spi_devices based on data in the device tree.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Improve PIO transfer mode of au1550 spi controller by continuing of spi
transfer, instead of aborting transfer when transmit underflow interrupt
occurrs.
Verified by oscilloscope that the spi clock pauses on trasmit underflow,
so transfer continuation is perfectly valid even though au1550 datasheet
says that on tx underflow zeroes will be transfered.
Also make some error messages more specific.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the Au1550 resource table and instead extract MMIO/IRQ/DMA
resources from platform resource information like any well-behaved
platform driver.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Another step to removing ->ioctl and to removing the BKL
[dbrownell@users.sourceforge.net: take final step; BKL not needed]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, 'modalias' in the spi_device structure is a 'const char *'.
The spi_new_device() function fills in the modalias value from a passed in
spi_board_info data block. Since it is a pointer copy, the new spi_device
remains dependent on the spi_board_info structure after the new spi_device
is registered (no other fields in spi_device directly depend on the
spi_board_info structure; all of the other data is copied).
This causes a problem when dynamically propulating the list of attached
SPI devices. For example, in arch/powerpc, the list of SPI devices can be
populated from data in the device tree. With the current code, the device
tree adapter must kmalloc() a new spi_board_info structure for each new
SPI device it finds in the device tree, and there is no simple mechanism
in place for keeping track of these allocations.
This patch changes modalias from a 'const char *' to a fixed char array.
By copying the modalias string instead of referencing it, the dependency
on the spi_board_info structure is eliminated and an outside caller does
not need to maintain a separate spi_board_info allocation for each device.
If searched through the code to the best of my ability for any references
to modalias which may be affected by this change and haven't found
anything. It has been tested with the lite5200b platform in arch/powerpc.
[dbrownell@users.sourceforge.net: cope with linux-next changes: KOBJ_NAME_LEN obliterated, etc]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use "if SPI_MASTER" to remove numerous dependencies.
[dbrownell@users.sourceforge.net: remove a couple now-needless EXPERIMENTAL dependencies too]
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
xilinx_spi->irq is unsigned, so the test fails
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Andrei Konovalov <akonovalov@ru.mvista.com>
Cc: Yuri Frolov <yfrolov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This updates the SPI clock rate calculations for the spi_mpc83xx driver.
Some boundary conditions were wrong, and in several cases divide-by-16
wasn't always needed
Signed-off-by: Chen Gong <g.chen@freescale.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This mirrors the functionality that driver_find_device has as well.
We add a start variable, and all callers of the function are fixed up at
the same time.
The block layer will be using this new functionality in a follow-on
patch.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Switch over to use the shiny new device_create_drvdata() call
instead of the original device_create() calls, so this continues
to work after device_create() is removed.
Note that this driver never had the race which motivated removing
the original call; it locked correctly.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (241 commits)
[ARM] 5171/1: ep93xx: fix compilation of modules using clocks
[ARM] 5133/2: at91sam9g20 defconfig file
[ARM] 5130/4: Support for the at91sam9g20
[ARM] 5160/1: IOP3XX: gpio/gpiolib support
[ARM] at91: Fix NAND FLASH timings for at91sam9x evaluation kits.
[ARM] 5084/1: zylonite: Register AC97 device
[ARM] 5085/2: PXA: Move AC97 over to the new central device declaration model
[ARM] 5120/1: pxa: correct platform driver names for PXA25x and PXA27x UDC drivers
[ARM] 5147/1: pxaficp_ir: drop pxa_gpio_mode calls, as pin setting
[ARM] 5145/1: PXA2xx: provide api to control IrDA pins state
[ARM] 5144/1: pxaficp_ir: cleanup includes
[ARM] pxa: remove pxa_set_cken()
[ARM] pxa: allow clk aliases
[ARM] Feroceon: don't disable BPU on boot
[ARM] Orion: LED support for HP mv2120
[ARM] Orion: add RD88F5181L-FXO support
[ARM] Orion: add RD88F5181L-GE support
[ARM] Orion: add Netgear WNR854T support
[ARM] s3c2410_defconfig: update for current build
[ARM] Acer n30: Minor style and indentation fixes.
...
This got broken by the recent "fix rmmod $spi_driver while spidev-user is
active". I tested the rmmod & write path but didn't check the read path.
I am sorry. The read logic changed and spidev_sync_read() +
spidev_sync_write() do not return zero on success anymore but the number
of bytes that has been transfered over the bus. This patch changes the
logic and copy_to_user() gets called again.
The write path returns the number of bytes which are written to the
underlying device what may be less than the requested size. This patch
makes the same change to the read path or else we request a read of 20
bytes, get 10, don't call copy to user and report to the user that we read
10 bytes.
[akpm@linux-foundation.org: remove test of known-to-be-zero local]
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
imx_dma_request_by_prio can return channel number by itself.
No need to supply variable address through parameters.
Also converted all drivers using this function.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This addresses other oopsing paths in "spidev" by changing how it manages
refcounting. It decouples the lifecycle of the per-device data from the
class device (not just the spi device):
- Use class_{create,destroy} not class_{register,unregister}.
- Use device_{create,destroy} not device_{register,unregister}.
- Free the per-device data only when TWO conditions are true:
* Driver is unbound from underlying SPI device, and
* Device is no longer open (new)
Also, spi_{get,set}_drvdata not dev_{get,set}_drvdata for simpler code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Sebastian Siewior <bigeasy@tglx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Somehow the spidev code forgot to include a critical mechanism: when the
underlying device is removed (e.g. spi_master rmmod), open file
descriptors must be prevented from issuing new I/O requests to that
device. On penalty of the oopsing reported by Sebastian Siewior
<bigeasy@tglx.de> ...
This is a partial fix, adding handshaking between the lower level (SPI
messaging) and the file operations using the spi_dev. (It also fixes an
issue where reads and writes didn't return the number of bytes sent or
received.)
There's still a refcounting issue to be addressed (separately).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Reported-by: Sebastian Siewior <bigeasy@tglx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current driver may cause glitches on SPI CLK line since one must disable
the SPI controller before changing any HW settings. Fix this by implementing
a local spi_transfer function that won't change speed and/or word size while
CS is active.
While doing that heavy lifting a few other issues were addressed too:
- Make word size 16 and 32 work too.
- Honor bits_per_word and speed_hz in spi transaction.
- Optimize the common path.
This also stops using the "bitbang" framework (except for a few constants).
[Roel Kluin <12o3l@tiscali.nl>: "irq" needs to be signed]
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a typo in pxa2xx_spi.c, comment says "Enable the SSP clock", code
says: clk_disable ... so after resume, the SSP is dead.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Ned Forrester <nforrester@whoi.edu>
Cc: Stephen Street <stephen@streetfiresound.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On Fri, Apr 18, 2008 at 09:08:55PM +0200, Julia Lawall wrote:
> I found 63 occurrences of this problem with the following semantic match
> (http://www.emn.fr/x-info/coccinelle/):
>
> @@ unsigned int i; @@
>
> * i < 0
>
Since this one's always in the range 0-255, it could probably be made
signed, but it's just as easy to make it work unsigned.
Reported-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use PIO for full-duplex transfers, instead of DMA.
Signed-off-by: Vitja Makarov <vitja.makarov@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the baud rate divisor calculation code a bit more readable and add a
few comments.
Also fix wrong debug information being displayed when !new_1 and
max_speed_hz == 0.
[david-b@pacbell.net: fix it]
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: "Janesh Ramakrishnan" <jramakrishnan@neuropace.com>
Acked-by David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Updates to the i.MX SPI controller driver:
1) Some comments changed and/or added.
2) End of transfers is now managed on TXFIFO empty interrupt after the
last write to TXFIFO. This speeds interrupt execution by removing
the wait for TXFIFO to become empty. On TXFIFO empty interrupt the
handler needs only to poll for the end of the ongoing transaction
(SPI_CONTROL_XCH) to close the transfer.
(2.1) Write only transfers are closed flushing RXFIFO.
(2.2) Read transfers are closed reading trailing bytes from RXFIFO.
(2.3) Read transfers where RXFIFO overrun occurred are closed by
flushing RXFIFO and aborting the message.
3) Fifos are now flushed via SPI disable after the end of ongoing
transaction.
Signed-off-by: Andrea Paterniani <a.paterniani@swapp-eng.it>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A spi transfer with zero length is not invalid. For example, such
transfer (len == 0 && delay_usecs != 0) can be used to achieve delay
before first CLK edge after chipselect assertion.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Various cleanups to pxa2xx_spi suggested by "sparse": make sure that
register addresess are "void __iomem *", and make a few functions properly
static.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Ned Forrester <nforrester@whoi.edu>
Cc: Stephen Street <stephen@streetfiresound.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SPI core now expects num_chipselect to be set correctly as due to added
checks on the chip being selected before an transfer is allowed. This patch
adds a num_cs field to the platform data which needs to be set correctly
before adding the SPI platform device.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pass the bus number we expect the S3C24XX SPI driver to attach to via the
platform data.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The s3c24xx_spi_txrx() function should initialise the completion each time
before using it, otherwise we end up with the possibility of returning success
before the interrupt handler has processed all the data.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>