Fixes setting low-resolution video modes on HDMI. Now the PLLH_PIX
divider adjusts itself until the PLLH is within bounds.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This clock is present on BCM53573 devices (including BCM47189) that use
Cortex-A7. ILP is a part of PMU (Power Management Unit) multi-function
device so we use syscon (and regmap) for it.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Rob Herring <robh@kernel.org>
[sboyd@codeaurora.org: Remove 0 from clk_init_data to silence sparse]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs.
Cc: Eric Anholt <eric@anholt.net>
Cc: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Make the clocks visible options that can be selected by anyone. This
avoids the problems of:
1) Select is a reverse dependency and is hard for people to understand
and can sometimes be a pain to track down
2) Build coverage goes down because configs are hidden
3) Code bloat
Patch suggested by Stephen Boyd
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kmalloc_array".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Alex Elder <elder@linaro.org>
[sboyd@codeaurora.org: Save a line]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
If the firmware had set up a clock to source from PLLC, go along with
it. But if we're looking for a new parent, we don't want to switch it
to PLLC because the firmware will force PLLC (and thus the AXI bus
clock) to different frequencies during over-temp/under-voltage,
without notification to Linux.
On my system, this moves the Linux-enabled HDMI state machine and DSI1
escape clock over to plld_per from pllc_per. EMMC still ends up on
pllc_per, because the firmware had set it up to use that.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the audio domain clocks")
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
While the SDRAM is being driven by its dedicated PLL most of the time,
there is a little loop running in the firmware that periodically turns
on the CM SDRAM clock (using its pre-initialized parent) and switches
SDRAM to using the CM clock to do PVT recalibration.
This avoids system hangs if we choose SDRAM's parent for some other
clock, then disable that clock.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
These divide off of PLLD_PER and are used for the ethernet and wifi
PHYs source PLLs. Neither of them is currently represented by a phy
device that would grab the clock for us.
This keeps other drivers from killing the networking PHYs when they
disable their own clocks and trigger PLLD_PER's refcount going to 0.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The VPU clock is also the clock for our AXI bus, so we really can't
disable it. This might have happened during boot if, for example,
uart1 (aux_uart clock) probed and was then disabled before the other
consumers of the VPU clock had probed.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we can use clk_hw pointers we don't need to have two
duplicate arrays holding the same mapping of clk index to clk_hw
pointer. Implement a custom clk_hw provider function to map the
OF specifier to the clk_hw instance for it.
Cc: Alex Elder <elder@linaro.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Now that we have clk_hw based provider APIs to register clks, we
can get rid of struct clk pointers while registering clks in
these drivers, allowing us to move closer to a clear split of
consumer and provider clk APIs.
Cc: Jon Mason <jonmason@broadcom.com>
Cc: Simran Rai <ssimran@broadcom.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Tested-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fix the implicit declaration of iproc_armpll_setup() by
including clk-iproc.h which defines it. Fixes the warning:
drivers/clk/bcm/clk-iproc-armpll.c:242:13: warning: symbol 'iproc_armpll_setup' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
When sizeof is applied to a pointer typed expression, it gives
the size of the pointer. So, here do not use sizeof on pointer
type. Also, silent checkpatch.pl by using kmalloc_array over
kmalloc.
Note that this has no effect on runtime because 'parent_names'
is a pointer to a pointer.
Problem found using Coccinelle.
Signed-off-by: Vaishali Thakkar <vaishali.thakkar@oracle.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
In poweroff, we set the reset bit and the power down bit, but only
managed to unset the reset bit for poweron. This meant that if HDMI
did -EPROBE_DEFER after it had grabbed its clocks, we'd power down the
PLLH (that had been on at boot time) and never recover.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the audio domain clocks")
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add AVE0, DFT, GP0, GP1, GP2, SLIM, SMI, TEC, DPI, CAM0, CAM1, DSI0E,
and DSI1E. PULSE is not added because it has an extra divider.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Enable the PCM clock in the SOC, which is used by the
bcm2835-i2s driver.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Reorganize bcm2835_clock_array so that there is no more
need for separate bcm2835_*_data structures to be defined.
Instead the required structures are generated inline via
helper macros.
To allow this to also work for pll alone it was required that
the parent_pll was changed from a pointer to bcm2835_pll_data
to the name of the pll instead.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
As the use of BCM2835_CLOCK_COUNT in
include/dt-bindings/clock/bcm2835.h is frowned upon as
it needs to get modified every time a new clock gets introduced
this patch changes the clk-bcm2835 driver to use a different
scheme for registration of clocks and pll, so that there
is no more need for BCM2835_CLOCK_COUNT to be defined.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
For debugging purposes under some circumstance
it helps to be able to see the actual clock registers.
E.g: when looking at the clock divider it is helpful to
see what the actual clock divider is.
This patch exposes all the clock registers specific to each
clock/pll/pll-divider via debugfs.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Eric Anholt <eric@anholt.net>
The current driver calculates the clock divider with
fractional support enabled.
But it does not enable fractional support in the
control register itself resulting in an integer only divider,
but in clk_set_rate responds back the fractionally divided
clock frequency.
This patch enables fractional support in the control register
whenever there is a fractional bit set in the requested clock divider.
Mash clock limits are are also handled for the PWM clock
applying the correct divider limits (2 and max_int) applicable to
basic fractional divider support (mash order of 1).
It also adds locking to protect the read/modify/write cycle of
the register modification.
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the
audio domain clocks")
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Current clamping of a normal divider allows a value < 1 to be valid.
A divider of < 1 would actually only be possible if we had a PLL...
So this patch clamps the divider to 1.
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the
audio domain clocks")
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Add missing locking to:
* bcm2835_pll_divider_on
* bcm2835_pll_divider_off
to protect the read modify write cycle for the
register access protecting both cm_reg and a2w_reg
registers.
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the
audio domain clocks")
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
bcm2835_pll_off is currently assigning CM_PLL_ANARST to the control
register, which may lose the other bits that are currently set by the
clock dividers.
It also now locks during the read/modify/write cycle of both
registers.
Fixes: 41691b8862 ("clk: bcm2835: Add support for programming the
audio domain clocks")
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
The change fixes potential oops while accessing iomem on invalid
address, if devm_ioremap_resource() fails due to some reason.
The devm_ioremap_resource() function returns ERR_PTR() and never
returns NULL, which makes useless a following check for NULL.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Fixes: 5e63dcc74b ("clk: bcm2835: Add a driver for the auxiliary peripheral clock gates")
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This flag is a no-op now. Remove usage of the flag.
Cc: Lee Jones <lee@kernel.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We were rolling this ourselves, but clk-divider can do it now.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Our dividers weren't being set successfully because CM_PASSWORD wasn't
included in the register write. It looks easier to just compute the
divider to write ourselves than to update clk-divider for the ability
to OR in some arbitrary bits on write.
Fixes about half of the video modes on my HDMI monitor (everything
except 720x400).
Cc: stable@vger.kernel.org
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Remove __init macro from all function prototypes in clk-iproc.h
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds support for Broadcom Cygnus audio PLL and leaf
clocks
Signed-off-by: Simran Rai <ssimran@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Register the pwm clock for bcm2835.
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Some bcm2835 clocks used by hardware (like "PWM" or "H264") can have multiple
parent clocks. These clocks divide the rate of a parent which can be selected by
setting the proper bits in the clock control register.
Previously all these parents where handled by a mux clock. But a mux clock
cannot be used because updating clock control register to select parent needs a
password to be xor'd with the parent index.
This patch get rid of mux clock and make these clocks handle their own parent,
allowing them to select the one to use.
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Make bcm2835_clock_choose_div to optionally round up the chosen MASH divisor
so that the resulting average rate will not be higher than the requested one.
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
There are a pair of SPI masters and a mini UART that were last minute
additions. As a result, they didn't get integrated in the same way as
the other gates off of the VPU clock in CPRMAN.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
BCM63138 has a simple clocking domain which is primarily the ARMPLL
clocking complex, from which the ARM (CPU), APB and AXI clocks would be
derived from.
Since the ARMPLL controller is entirely compatible with the iProc ARM
PLL, we just initialize it without additional parameters.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
* clk-iproc:
clk: iproc: define Broadcom NS2 iProc clock binding
clk: iproc: define Broadcom NSP iProc clock binding
clk: ns2: add clock support for Broadcom Northstar 2 SoC
clk: iproc: Separate status and control variables
clk: iproc: Split off dig_filter
clk: iproc: Add PLL base write function
clk: nsp: add clock support for Broadcom Northstar Plus SoC
clk: iproc: Add PWRCTRL support
clk: cygnus: Convert all macros to all caps
ARM: cygnus: fix link failures when CONFIG_COMMON_CLK_IPROC is disabled
The Broadcom Northstar 2 SoC is architected under the iProc
architecture. It has the following PLLs: GENPLL SCR, GENPLL SW,
LCPLL DDR, LCPLL Ports, all derived from an onboard crystal.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some PLLs have separate registers for Status and Control. The means the
pll_base needs to be split into 2 new variables, so that those PLLs can
specify device tree registers for those independently. Also, add a new
driver flag to identify this presence of the split, and let the driver
know that additional registers need to be used.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The PLL loop filter/gain can be located in a separate register on some
SoCs. Split these off into a separate variable, so that an offset can
be added if necessary. Also, make the necessary modifications to the
Cygnus and NSP drivers for this change.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
All writes to the PLL base address must be flushed if the
IPROC_CLK_NEEDS_READ_BACK flag is set. If we add a function to make the
necessary write and reads, we can make sure that any future code which
makes PLL base writes will do the correct thing.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The Broadcom Northstar Plus SoC is architected under the iProc
architecture. It has the following PLLs: ARMPLL, GENPLL, LCPLL0, all
derived from an onboard crystal.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some iProc SoC clocks use a different way to control clock power, via
the PWRDWN bit in the PLL control register. Since the PLL control
register is used to access the PWRDWN bit, there is no need for the
pwr_base when this is being used. A new flag, IPROC_CLK_EMBED_PWRCTRL,
has been added to identify this usage. We can use the AON interface to
write the values to enable/disable PWRDOWN.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
[sboyd@codeaurora.org: Remove useless parentheses]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The macros that are being used to initialize the values of the clk
structures should be all caps. Find and replace all of them with their
relevant counterparts.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
When CONFIG_CYGNUS is set but CONFIG_COMMON_CLK_IPROC is disabled, the
following link failures are caused:
drivers/built-in.o: In function `cygnus_armpll_init':
:(.init.text+0x1d290): undefined reference to `iproc_armpll_setup'
drivers/built-in.o: In function `cygnus_genpll_clk_init':
:(.init.text+0x1d2c4): undefined reference to `iproc_pll_clk_setup'
drivers/built-in.o: In function `cygnus_lcpll0_clk_init':
:(.init.text+0x1d304): undefined reference to `iproc_pll_clk_setup'
drivers/built-in.o: In function `cygnus_mipipll_clk_init':
:(.init.text+0x1d344): undefined reference to `iproc_pll_clk_setup'
drivers/built-in.o: In function `cygnus_asiu_init':
:(.init.text+0x1d370): undefined reference to `iproc_asiu_setup'
It is fixed it by always selecting COMMON_CLK_IPROC from
ARCH_BCM_IPROC, and making COMMON_CLK_IPROC a silent option (thus
preventing it from being erroneously disabled by a user).
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Eric Anholt