The ixgbevf_qv_disable function used by CONFIG_NET_RX_BUSY_POLL is broken,
because it does not properly set the IXGBEVF_QV_STATE_DISABLED bit, indicating
that the q_vector should be disabled (and preventing future locks from
obtaining the vector). This patch corrects the issue by setting the disable
state.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ixgbe_service_task() is calling ixgbe_reinit_locked() without
the rtnl_lock being held. This is because it is being called
from a worker thread and not a rtnl netlink or dcbnl path.
Add rtnl_{un}lock() semantics. I found this during code review.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In PM_SUSPEND_FREEZE and WOL(Wakeup On Lan) case, when the driver gets a
wakeup event, either the driver or platform specific PM code should notify
the pm core about it, so that the system can wakeup from low power.
In cases where there is no involvement of platform specific PM, it
becomes driver responsibility to notify the PM core to wakeup the
system.
Without this WOL with PM_SUSPEND_FREEZE does not work on STi based SOCs.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to restore default pinstate of the pins when it
comes back from low power state. Without this patch the state of the
pins would be unknown and the driver would not work.
This patch also adds code to put the pins in to sleep state when the
driver enters low power state.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hibernation freeze case the driver just releases the resources like
dma buffers, irqs, unregisters the drivers and during restore it does
register, request the resources. This is not really necessary, as part
of power management all the data structures are intact, all the
previously allocated resources can be used after coming out of low
power.
This patch uses the suspend and resume callbacks for freeze and
restore which initializes the hardware correctly without unregistering
or releasing the resources, this should also help in reducing the time
to restore.
Also this patch fixes a bug in stmmac_pltfr_restore and
stmmac_pltfr_freeze where it tries to get hold of platform data via
dev_get_platdata call, which would return NULL in device tree cases and
the next if statement would crash as there is no NULL check.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver PM resume assumes that the IP is still powered up and the
all the register contents are not disturbed when it comes out of low
power suspend case. This assumption is wrong, basically the driver
should not consider any state of registers after it comes out of low
power. However driver can keep the part of the IP powered up if its a
wake up source. But it can not assume the register state of the IP. Also
its possible that SOC glue layer can take the power off the IP if its
not wake-up source to reduce the power consumption.
This patch re initializes hardware by calling stmmac_hw_setup function in
resume case.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch promotes stmmac_mdio_reset function from static to
non-static, so that power management functions can decide to reset if
the IP comes out from lowe power state specially hibernation cases.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves hardware setup part of the code in stmmac_open to a new
function stmmac_hw_setup, the reason for doing this is to make hw
initialization independent function so that PM functions can re-use it to
re-initialize the IP after returning from low power state.
This will also avoid code duplication across stmmac_resume/restore and
stmmac_open.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves dma resource allocation to a new function
alloc_dma_desc_resources, the reason for moving this to a new function
is to keep the memory allocations in a separate function. One more reason
it to get suspend and hibernation cases working without releasing and
allocating these resources during suspend-resume and freeze-restore
cases.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes gpio_free for reset line of the phy, driver stores
the gpio number in its private data-structure to use in future. As the
driver uses this pin in future this pin should not be freed.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to "max-speed" property which is a standard
Ethernet device tree property. max-speed specifies maximum speed
(specified in megabits per second) supported the device.
Depending on the clocking schemes some of the boards can only support
few link speeds, so having a way to limit the link speed in the mac
driver would allow such setups to work reliably.
Without this patch there is no way to tell the driver to limit the
link speed.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function return parameter is not used in mvneta_tx_done_gbe(),
where the function is called. This patch makes the function return
void.
Reviewed-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
mvneta_tx_done_gbe() return value and third parameter are no more
used. This patch changes the function prototype and removes a useless
variable where the function is called.
Reviewed-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
calling dma_map_single()/dma_unmap_single() is quite expensive compared
to copying a small packet. So let's copy short frames and keep the buffers
mapped. We set the limit to 256 bytes which seems to give good results both
on the XP-GP board and on the AX3/4.
The Rx small packet rate increased by 16.4% doing this, from 486kpps to
573kpps. It is worth noting that even the call to the function
dma_sync_single_range_for_cpu() is expensive (300 ns) although less
than dma_unmap_single(). Without it, the packet rate raises to 711kpps
(+24% more). Thus on systems where coherency from device to CPU is
guaranteed by a snoop control unit, this patch should provide even more
gains, and probably rx_copybreak could be increased.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of build_skb() to allocate frags on the RX path. When frag size
is lower than a page size, we can use netdev_alloc_frag(), and we fall back
to kmalloc() for larger sizes. The frag size is stored into the mvneta_port
struct. The alloc/free functions check the frag size to decide what alloc/
free method to use. MTU changes are safe because the MTU change function
stops the device and clears the queues before applying the change.
With this patch, I observed a reproducible 2% performance improvement on
HTTP-based benchmarks, and 5% on small packet RX rate.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the mvneta driver tries to prefetch the current Rx
descriptor during read. Tests have shown that prefetching the
next one instead increases general performance by about 1% on
HTTP traffic.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
At several places, we already know the value of the rx status but
we call functions which dereference the pointer again to get it
and don't need the descriptor for anything else. Simplify this
task by replacing the rx desc pointer by the status word itself.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make mvneta_rxq_fill() use mvneta_rx_refill() instead of using
duplicate code.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, mvneta_txq_bufs_free() calls mvneta_tx_done_policy() with
a non-null cause to retrieve the pointer to the next queue to process.
There are useless tests on the return queue number and on the pointer,
all of which are well defined within a known limited set. This code
path is fast, although not critical. Removing 3 tests here that the
compiler could not optimize (verified) is always desirable.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now the mvneta driver doesn't handle Tx IRQ, and relies on two
mechanisms to flush Tx descriptors : a flush at the end of mvneta_tx()
and a timer. If a burst of packets is emitted faster than the device
can send them, then the queue is stopped until next wake-up of the
timer 10ms later. This causes jerky output traffic with bursts and
pauses, making it difficult to reach line rate with very few streams.
A test on UDP traffic shows that it's not possible to go beyond 134
Mbps / 12 kpps of outgoing traffic with 1500-bytes IP packets. Routed
traffic tends to observe pauses as well if the traffic is bursty,
making it even burstier after the wake-up.
It seems that this feature was inherited from the original driver but
nothing there mentions any reason for not using the interrupt instead,
which the chip supports.
Thus, this patch enables Tx interrupts and removes the timer. It does
the two at once because it's not really possible to make the two
mechanisms coexist, so a split patch doesn't make sense.
First tests performed on a Mirabox (Armada 370) show that less CPU
seems to be used when sending traffic. One reason might be that we now
call the mvneta_tx_done_gbe() with a mask indicating which queues have
been done instead of looping over all of them.
The same UDP test above now happily reaches 987 Mbps / 87.7 kpps.
Single-stream TCP traffic can now more easily reach line rate. HTTP
transfers of 1 MB objects over a single connection went from 730 to
840 Mbps. It is even possible to go significantly higher (>900 Mbps)
by tweaking tcp_tso_win_divisor.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Arnaud Ebalard <arno@natisbad.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell has not published the chip's datasheet yet, so it's very hard
to find the relevant bits to manipulate to change the IRQ behaviour.
Fortunately, these bits are described in the proprietary LSP patch set
which is publicly available here :
http://www.plugcomputer.org/downloads/mirabox/
So let's put them back in the driver in order to reduce the burden of
current and future maintenance.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a queue timeout is reported, we can oops because of some
schedules while the caller is atomic, as shown below :
mvneta d0070000.ethernet eth0: tx timeout
BUG: scheduling while atomic: bash/1528/0x00000100
Modules linked in: slhttp_ethdiv(C) [last unloaded: slhttp_ethdiv]
CPU: 2 PID: 1528 Comm: bash Tainted: G WC 3.13.0-rc4-mvebu-nf #180
[<c0011bd9>] (unwind_backtrace+0x1/0x98) from [<c000f1ab>] (show_stack+0xb/0xc)
[<c000f1ab>] (show_stack+0xb/0xc) from [<c02ad323>] (dump_stack+0x4f/0x64)
[<c02ad323>] (dump_stack+0x4f/0x64) from [<c02abe67>] (__schedule_bug+0x37/0x4c)
[<c02abe67>] (__schedule_bug+0x37/0x4c) from [<c02ae261>] (__schedule+0x325/0x3ec)
[<c02ae261>] (__schedule+0x325/0x3ec) from [<c02adb97>] (schedule_timeout+0xb7/0x118)
[<c02adb97>] (schedule_timeout+0xb7/0x118) from [<c0020a67>] (msleep+0xf/0x14)
[<c0020a67>] (msleep+0xf/0x14) from [<c01dcbe5>] (mvneta_stop_dev+0x21/0x194)
[<c01dcbe5>] (mvneta_stop_dev+0x21/0x194) from [<c01dcfe9>] (mvneta_tx_timeout+0x19/0x24)
[<c01dcfe9>] (mvneta_tx_timeout+0x19/0x24) from [<c024afc7>] (dev_watchdog+0x18b/0x1c4)
[<c024afc7>] (dev_watchdog+0x18b/0x1c4) from [<c0020b53>] (call_timer_fn.isra.27+0x17/0x5c)
[<c0020b53>] (call_timer_fn.isra.27+0x17/0x5c) from [<c0020cad>] (run_timer_softirq+0x115/0x170)
[<c0020cad>] (run_timer_softirq+0x115/0x170) from [<c001ccb9>] (__do_softirq+0xbd/0x1a8)
[<c001ccb9>] (__do_softirq+0xbd/0x1a8) from [<c001cfad>] (irq_exit+0x61/0x98)
[<c001cfad>] (irq_exit+0x61/0x98) from [<c000d4bf>] (handle_IRQ+0x27/0x60)
[<c000d4bf>] (handle_IRQ+0x27/0x60) from [<c000843b>] (armada_370_xp_handle_irq+0x33/0xc8)
[<c000843b>] (armada_370_xp_handle_irq+0x33/0xc8) from [<c000fba9>] (__irq_usr+0x49/0x60)
Ben Hutchings attempted to propose a better fix consisting in using a
scheduled work for this, but while it fixed this panic, it caused other
random freezes and panics proving that the reset sequence in the driver
is unreliable and that additional fixes should be investigated.
When sending multiple streams over a link limited to 100 Mbps, Tx timeouts
happen from time to time, and the driver correctly recovers only when the
function is disabled.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stats writers are mvneta_rx() and mvneta_tx(). They don't lock anything
when they update the stats, and as a result, it randomly happens that
the stats freeze on SMP if two updates happen during stats retrieval.
This is very easily reproducible by starting two HTTP servers and binding
each of them to a different CPU, then consulting /proc/net/dev in loops
during transfers, the interface should immediately lock up. This issue
also randomly happens upon link state changes during transfers, because
the stats are collected in this situation, but it takes more attempts to
reproduce it.
The comments in netdevice.h suggest using per_cpu stats instead to get
rid of this issue.
This patch implements this. It merges both rx_stats and tx_stats into
a single "stats" member with a single syncp. Both mvneta_rx() and
mvneta_rx() now only update the a single CPU's counters.
In turn, mvneta_get_stats64() does the summing by iterating over all CPUs
to get their respective stats.
With this change, stats are still correct and no more lockup is encountered.
Note that this bug was present since the first import of the mvneta
driver. It might make sense to backport it to some stable trees. If
so, it depends on "d33dc73 net: mvneta: increase the 64-bit rx/tx stats
out of the hot path".
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Better count packets and bytes in the stack and on 32 bit then
accumulate them at the end for once. This saves two memory writes
and two memory barriers per packet. The incoming packet rate was
increased by 4.7% on the Openblocks AX3 thanks to this.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch will also change behavior of rx_beacons statistic.
Instead of collecting all received beacons, it will collect only
ours. This, IMO make more sense, since for troubleshooting we will
need to know count of our beacons, or both.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this function is used by most ath driver, so it can be moved here.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While registering the driver with cfg80211, update the threshold
value and retry limit to cfg80211.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bit 14 is actually reserved and bit 12 & 13 should be used for
11ac capability in fw_cap_info.
Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes bug found by the kbuild test robot:
tree: git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next.git master
head: 1e2f9295f4
commit: 1cbbcb08c7 [135/140] wil6210: prefetch head of packet
config: make ARCH=microblaze allyesconfig
All error/warnings:
drivers/net/wireless/ath/wil6210/txrx.c: In function 'wil_vring_reap_rx':
>> drivers/net/wireless/ath/wil6210/txrx.c:381:2: error: implicit declaration of function 'prefetch' [-Werror=implicit-function-declaration]
prefetch(skb->data);
^
cc1: some warnings being treated as errors
vim +/prefetch +381 drivers/net/wireless/ath/wil6210/txrx.c
375 wil_err(wil, "Rx size too large: %d bytes!\n", dmalen);
376 kfree_skb(skb);
377 return NULL;
378 }
379 skb_trim(skb, dmalen);
380
> 381 prefetch(skb->data);
382
383 wil_hex_dump_txrx("Rx ", DUMP_PREFIX_OFFSET, 16, 1,
384 skb->data, skb_headlen(skb), false);
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prevent a possible overflow condition which results in occasional
bad IQ coefficients and EVM numbers.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug in the TX IQ calibration post
processing routine because of which the driver disables
TX IQ correction even though the calibration results
are valid. This fix is applicable for all chips in the
AR9003 family.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When removing the card the driver still tries to access registers
in the device. This patch adds another state for the bus that
indicates the device is no longer reachable. This avoids errors
accessing it while cleaning up the driver.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For scheduled scan results the driver does a escan to obtain BSS
details from the firmware. However, the escan uses a dynamically
determined function. This needs to be set appropriately when handling
scheduled scan results to avoid NULL pointer access.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rework function to allow only bcm4329 in case of chip backplane
type being sonics sillicon backplane.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware download code has been restructured so the reset vector
does not need to be stored in a structure, but keep it on the stack
to be passed to exit download function.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The original core reset and disable routines do not work always
on running system. These routines were updated to properly reset
a core. When module is unloaded the device is put into download
state where all necessary cores have been reset. This will make
sure the device is in idle mode after module unload.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New bus layers like pcie require nvram parsing routines which are
the same routines as being used by sdio. Make these routines common
in the new file nvram.c. Update sdio to use these routines and
simplify the nvram upload process. Also add memory validation check
for downloaded firmware and nvram in debug mode.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx head write-back registers are not cleared during an FLR or VF reset.
As a result a configuration that had head write-back enabled can leave the
registers set after the driver is unloaded. If the next driver loaded doesn't
use the write-back registers this can lead to a bad configuration where
head write-back is enabled, but the driver didn't request it.
To avoid this situation the PF should be resetting the Tx head write-back
registers when the VF requests a reset.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that the QDE bits are set for a VF before the Rx
queues are enabled. As such we avoid head of line blocking in the event
that the VF stops cleaning Rx descriptors for whatever reason.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
drivers/net/ethernet/intel/ixgbe/ixgbe_sriov.c | 14 ++++++++++++++
drivers/net/ethernet/intel/ixgbe/ixgbe_type.h | 7 ++++---
2 files changed, 18 insertions(+), 3 deletions(-)
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver does not check value returned by dma_map_page. The patch
fixes this.
v2: Removed the bugfix for non-bug ;-) (thanks Sathya)
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Sathya Perla <Sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bnx2x driver in its pci shutdown() callback releases its pci bars (in the
same manner it does during its pci remove() callback).
During a system reboot while VFs are enabled, its possible for the VF's remove
to be called (as a result of pci_disable_sriov()) after its shutdown callback
has already finished running; This will cause a paging request fault as the VF
tries to access the pci bar which it has previously released, crashing the
system.
This patch further differentiates the shutdown and remove callbacks, preventing the
pci release procedures from being called during shutdown.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans-up wake-on-lan code in the following ways:
1) Removes some driver hacks in be_cmd_get_acpi_wol_cap() that were based
on incorrect assumptions.
2) Uses the adapter->wol_en and wol_cap variables for checking if WoL
is supported and enabled on an interface instead of referring to the
exclusion list via the macro be_is_wol_supported()
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of NTKW_MAC_QUERY cmd has been deprecated for Skyhawk-R.
Replace the last remaining usage in be_vfs_mac_query() routine.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead, use the tail of the RXQ to pick the associated RXQ entry
This fix is required in preparation for supporting RXQ lengths greater than 1K.
For such queues, the frag index in the RX-compl entry is not valid as it is only a 10 bit entry not capable of addressing RXQs longer than 1K.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As be2net is used even by the 40Gbps Skyhawk-R chip
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An earlier commit (f25b119c "Fix error messages while driver load for VFs")
incorrectly set the adapter->cmd_privileges value for VFs (in a
multi-channel config) to MAX_PRIVILEGES. This causes FW cmd failures
and avoidable error logs when certian cmds are issued by a VF.
Also, move the multi-channel hack to be_cmds.c inside
be_cmd_get_fn_privileges() routine.
Fixes: f25b119c "Fix error messages while driver load for VFs"
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An ndo_set_mac_addr() call may be issued for a mac-addr that is already
active on an interface. If so, silently ignore the request. Sending such
a request to the FW, causes a "mac collision" error. The error is harmless
but is avoidable noise in the kernel log.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Skyhawk-R FW does not support SET/GET_EXT_FAT_CAPABILITIES cmds via which
FW logging level can be controlled. Also, the hack used in BE3 to control
FW logging level via the ethtool interface is not needed in Skyhawk-R.
This patch also cleans up this code by moving be_set/get_fw_log_level()
routines to be_cmds.c where they belong.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
remove new line
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the GET_HSW_CONFIG cmd, the "pport" field must be set only while
querying the switch mode. When the "pport" field is set, the
"interface_id" field must be set to the port number, otherwise, it
must be set to adapter->if_handle.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently this cmd is used only for Lancer.
MCC_CREATE_EXT_V1 supports larger CQ-ids and additional event codes for the
async_event_bitmap field.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rhine_reset_task() misses to disable the tx scheduler upon reset,
this can lead to a crash if work is still scheduled while we're resetting
the tx queue.
Fixes:
[ 93.591707] BUG: unable to handle kernel NULL pointer dereference at 0000004c
[ 93.595514] IP: [<c119d10d>] rhine_napipoll+0x491/0x6
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRO requires VLANs to be removed before aggregation can occur.
The Synopsys EMAC does not strip VLAN tags so this must be
done by the driver.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix new sparse warning about function declared static.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM to bypass build failures.
drivers/built-in.o: In function `orion_mdio_probe':
drivers/net/ethernet/marvell/mvmdio.c:228: undefined reference to `devm_ioremap'
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes unhandled register write in gianfar_ethtool.c.
Fixes following endianess related functional issues,
reported by sparse as well, i.e.:
gianfar_ethtool.c:1058:33: warning:
incorrect type in argument 1 (different base types)
expected unsigned int [unsigned] [usertype] value
got restricted __be32 [usertype] ip4src
gianfar_ethtool.c:1164:33: warning:
restricted __be16 degrades to integer
gianfar_ethtool.c:1669:32: warning:
invalid assignment: ^=
left side has type restricted __be16
right side has type int
Solves all the sparse warnings for mixig normal pointers
with __iomem pointers for gianfar_ptp.c, i.e.:
gianfar_ptp.c:163:32: warning:
incorrect type in argument 1 (different address spaces)
expected unsigned int [noderef] <asn:2>*addr
got unsigned int *<noident>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delete a variable that is at most only assigned to a constant, but never
used otherwise. In this code, it is the variable result that is used for
the return code, not rc.
A simplified version of the semantic patch that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
identifier i;
constant c;
@@
-T i;
<... when != i
-i = c;
...>
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
On port VLAN deletion the list of MAC filters for the virtual function (VF)
VSI were all deleted. Let's keep them around, they come in handy for keeping
the VF functional.
Change-Id: I335e760392f274dc8b8b40efcb708f65b49d7973
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The i40e Physical Function (PF) driver will allow the
Virtual Function (VF) driver to configure its own VLAN filters if no port
VLAN filter has been configured. This leads to the possibility of the
administrator setting a port VLAN filter for the VF after the VF has already
configured its own VLAN filters. This leads to a conflict that can only be
resolved by reloading the VF driver. When the conflicting administrative
command is detected in setting the port VLAN then log a message indicating to
the system administrator that he must now reload the VF driver for the new
port VLAN settings to take effect.
Change-Id: I8de73b885d944a043aff32226297e4249862bcad
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should use vxlan_dellink() handler in vxlan_exit_net(), since
i) we're not in fast-path and we should be consistent in dismantle
just as we would remove a device through rtnl ops, and more
importantly, ii) in case future code will kfree() memory in
vxlan_dellink(), we would leak it right here unnoticed. Therefore,
do not only half of the cleanup work, but make it properly.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can create a vxlan device with an explicit underlying carrier.
In that case, when the carrier link is being deleted from the
system (e.g. due to module unload) we should also clean up all
created vxlan devices on top of it since otherwise we're in an
inconsistent state in vxlan device. In that case, the user needs
to remove all such devices, while in case of other virtual devs
that sit on top of physical ones, it is usually the case that
these devices do unregister automatically as well and do not
leave the burden on the user.
This work is not necessary when vxlan device was not created with
a real underlying device, as connections can resume in that case
when driver is plugged again. But at least for the other cases,
we should go ahead and do the cleanup on removal.
We don't register the notifier during vxlan_newlink() here since
I consider this event rather rare, and therefore we should not
bloat vxlan's core structure unecessary. Also, we can simply make
use of unregister_netdevice_many() to batch that. fdb is flushed
upon ndo_stop().
E.g. `ip -d link show vxlan13` after carrier removal before
this patch:
5: vxlan13: <BROADCAST,MULTICAST> mtu 1450 qdisc noop state DOWN mode DEFAULT group default
link/ether 1e:47:da:6d:4d:99 brd ff:ff:ff:ff:ff:ff promiscuity 0
vxlan id 13 group 239.0.0.10 dev 2 port 32768 61000 ageing 300
^^^^^
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vlan gets the same netdev features except vlan filter.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Additional checks are needed for a detected removal not to cause
problems. Some involve simply avoiding a lot of stuff that can't
do anything good, and also cases where the phony return value can
cause problems. In addition, down the adapter when the removal is
sensed.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent writes to an adapter that has been detected as removed
by a previous failing read. This also fixes some include file
ordering confusion that this patch revealed.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check all register reads for adapter removal by checking the status
register after any register read that returns 0xFFFFFFFF. Since the
status register will never return 0xFFFFFFFF unless the adapter is
removed, such a value from a status register read confirms the
removal.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the ethtool register test use the normal register accessor
functions. Also eliminate macros used for calling register test
functions to make error exits clearer. Use boolean values for
boolean returns instead of 0 and 1.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kernel coding standard prefers static inline functions instead
of macros, so use them for register accessors. This is to prepare
for adding LER, Live Error Recovery, checks to those accessors.
Temporarily provide macros for calling the new static inline
accessors until all references are changed.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ixgbe_down function can now prevent multiple executions by
doing test_and_set_bit on __IXGBE_DOWN. This did not work before
introduction of the __IXGBE_REMOVING bit, because of overloading
of __IXGBE_DOWN. Also add smp_mb__before_clear_bit call before
clearing the __IXGBE_DOWN bit.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a bit, __IXGBE_REMOVING, to indicate that the module is being
removed. The __IXGBE_DOWN bit had been overloaded for this purpose,
but that leads to trouble. A few places now check both __IXGBE_DOWN
and __IXGBE_REMOVE. Notably, setting either bit will prevent service
task execution.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the driver version to 0.3.30-k.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some un-necessary parenthesis.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix some whitespace and comment issues.
Change-ID: I1587599e50ce66fd389965720e86f9e331d86643
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make this message mean something, rather than just spitting out a VSI id
without any context whatsoever.
Change-ID: Iafb906c6db46d4b5dcbe84adc9ed44730d08bd42
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bug where the queue was not associated with the right set-up
within the hardware. The fix is to use the right QTX_CTL VSI type
when associating it to the VSI.
Change-ID: I65ef6c5a8205601c640a6593e4b7e78d6ba45545
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This write done at the end of VF reset and should not be performed here.
Change-ID: I4d89813b68c6173184293868a6f26cf559bc2405
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following call chains indicate that vxlan_fdb_parse() is
under rtnl_lock protection. So if we use __dev_get_by_index()
instead of dev_get_by_index() to find interface handler in it,
this would help us avoid to change interface reference counter.
rtnetlink_rcv()
rtnl_lock()
netlink_rcv_skb()
rtnl_fdb_add()
vxlan_fdb_add()
vxlan_fdb_parse()
rtnl_unlock()
rtnetlink_rcv()
rtnl_lock()
netlink_rcv_skb()
rtnl_fdb_del()
vxlan_fdb_del()
vxlan_fdb_parse()
rtnl_unlock()
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following call chain indicates that eql_ioctl(), eql_enslave(),
eql_emancipate(), eql_g_slave_cfg() and eql_s_slave_cfg() are
protected under rtnl_lock. So if we use __dev_get_by_name() instead
of dev_get_by_name() to find interface handlers in them, this would
help us avoid to change interface reference counters.
dev_ioctl()
rtnl_lock()
dev_ifsioc()
eql_ioctl()
eql_enslave()
eql_emancipate()
eql_g_slave_cfg()
eql_s_slave_cfg()
rtnl_unlock()
Additionally we also change their return values from -EINVAL to
-ENODEV in case that interfaces are no found.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following call chain indicates that bond_do_ioctl() is protected
under rtnl_lock. If we use __dev_get_by_name() instead of
dev_get_by_name() to find interface handler in it, this would
help us avoid to change reference counter of interface once.
dev_ioctl()
rtnl_lock()
dev_ifsioc()
bond_do_ioctl()
rtnl_unlock()
Additionally we also change the coding style in bond_do_ioctl(),
letting it more readable for us.
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the limitation that the ecm and r8152 drivers couldn't coexist.
- Remove the devices from the blacklist of relative drivers.
- Remove usb_driver_set_configuration() from r8152 driver.
- Modify the id_table of the r8152 driver for the vendor mode only.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following warnings and error:
- WARNING: usb_free_urb(NULL) is safe this check is probably not required
- WARNING: kfree(NULL) is safe this check is probably not required
- ERROR: do not use C99 // comments
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The r8152 could support RTL8153. Update the relative descriptor.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bgmac_mii_register() and register_netdev() both return appropriate error
codes for the failures they would encounter, propagate this error code
instead of overriding the value with -ENOTSUPP which is not the correct
error code to return.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of new dm96xx variants now exist.
Reported-by: Joseph Chang <joseph_chang@davicom.com.tw>
Signed-off-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Ben Hutchings pointed out for the stats in alx, some
hardware-specific stats aren't matched to the right net_device_stats
field. Also fix the collision field and include errors in the total
number of RX/TX packets. Add a rx_dropped field and use it where
netdev->stats was modified directly out of the stats update function.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Ben Hutchings pointed out for the stats in alx, some
hardware-specific stats aren't matched to the right net_device_stats
field. Also fix the collision field and include errors in the total
number of RX/TX packets.
Minor whitespace fixes to match the style in alx.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Ben Hutchings pointed out for the stats in alx, some
hardware-specific stats aren't matched to the right net_device_stats
field. Also fix the collision field and include errors in the total
number of RX/TX packets.
Minor whitespace fixes to match the style in alx.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch bnx2x will configure the PF to perform Tx switching on
out-going traffic as soon as SR-IOV is dynamically enabled and de-activate
it when it is disabled.
This will allow VFs to communicate with their parent PFs.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
this is a pull request of three patches for net-next/master.
Oleg Moroz added support for a new PCI card to the generic SJA1000 PCI
driver, Guenter Roeck's patch limits the flexcan driver to little
endian arm (and powerpc) and I fixed a sparse warning found by the
kbuild robot in the ti_hecc driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use skb_checksum_setup to set up partial checksum offsets rather
then a private implementation.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use skb_checksum_setup to set up partial checksum offsets rather
then a private implementation.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for allocating IB UD QPs that we can steer
traffic from. We introduce a new firmware command FLOW_STEERING_IB_UC_QP_RANGE
and a capability bit.
This command isn't supported for VFs.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit 60e453a940 ("USBNET: fix handling padding packet")
added an extra SG entry in case padding is necessary, but
failed to update the initialisation of the list. This can
cause list traversal to fall off the end of the list,
resulting in an oops.
Fixes: 60e453a940 ("USBNET: fix handling padding packet")
Reported-by: Thomas Kear <thomas@kear.co.nz>
Cc: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Tested-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit c466a9b2b3
(net: 3com: slight optimization of addr compare)
cause a warning: "passing argument 1 of 'ether_addr_equal'
from incompatible pointer type", so fix it.
I think julia will convert ether_addr_equal to ether_addr_equal_64bits later.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 6878f79a8b
(net: qlcnic: slight optimization of addr compare)
cause a warning "sparse: incorrect type in argument 2
(different type sizes)", so fix it.
I think julia will convert ether_addr_equal to ether_addr_equal_64bits later.
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sh_eth_error() in case of a TX error tries to print a message using 2 dev_err()
calls with the first string not finished by '\n', so that the resulting message
would inevitably come out garbled, with something like "3net eth0: " inserted
in the middle. Avoid that by merging 2 calls into one.
While at it, insert an empty line after the nearby declaration.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the implementation is meaningless - once again, we take the
slave structure and use it after we've exited RCU critical section.
Fix this by removing the rcu_read_lock() from __get_active_agg(), and
ensuring that all its callers are holding RCU.
Fixes: be79bd048 ("bonding: add RCU for bond_3ad_state_machine_handler()")
CC: dingtianhong@huawei.com
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the RCU read lock usage is just wrong - it gets the slave struct
under RCU and continues to use it when RCU lock is released.
However, it's still safe to do this cause we didn't need the
rcu_read_lock() initially - all of the __get_first_agg() callers are either
holding RCU read lock or the RTNL lock, so that we can't sync while in it.
Fixes: be79bd048 ("bonding: add RCU for bond_3ad_state_machine_handler()")
CC: dingtianhong@huawei.com
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, its usage is just plainly wrong. It first gets a slave under
RCU, and, after releasing the RCU lock, continues to use it - whilst it can
be freed.
Fix this by ensuring that bond_3ad_set_carrier() holds RCU till it uses its
slave (or its agg).
Fixes: be79bd048a ("bonding: add RCU for bond_3ad_state_machine_handler()")
CC: dingtianhong@huawei.com
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Enabling BIT_9 while configuring hardware LRO allows adapter to
perform LRO even if destination IP address is not programmed in adapter.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Add __QLCNIC_SRIOV_ENABLE bit check before doing SRIOV cleanup
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Refactored code to handle beaconing test for all adapters.
o Use GET_LED_CONFIG mailbox command for 83xx/84xx series adapter
to detect current beaconing state of the adapter.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o MAC learning will be done for SRIOV PF to help program VLAN filters
onto adapter. This will help VNIC traffic to flow through without
flooding traffic.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o By default, SRIOV PF will have promiscous mode on.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o On enabling VF flood bit, PF driver will be able to receive traffic
from all its VFs.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Adapter should allow vlan traffic only for vlans configured on a VF.
On configuring any vlan mode from VF, adapter will allow any vlan
traffic to pass for that VF. Do not allow VF to configure this mode.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_attach_direct() may now attach to a generic 10G driver. It can
also be used exactly as phy_connect_direct(), which will be useful
when using of_mdio, as phy_connect (and therefore of_phy_connect)
start the PHY state machine, which is currently irrelevant for 10G
PHYs.
Signed-off-by: Andy Fleming <afleming@gmail.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Very incomplete, but will allow for binding an ethernet controller
to it.
Signed-off-by: Andy Fleming <afleming@gmail.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Then other generic phy driver such as generic 10g phy driver can join it.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keeping this as 0 is ok according to spec section 9.7.11
as this means the limits are according to the Tx/Rx
supported MCS x NSS bitmap. Initially we've set these as
there were concerns of interop issues but these turned out
to be false.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If we try to write NVM that do not exist, the function will return
uninitialized value. fixed.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add an inline helper function for getting an RX packet's
length or payload length and use it throughout the code
(most of which I did using an spatch.)
While at it, adjust some code, and remove a bogus comment
from the dvm calibration code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
All beamformee supporting chips have the ability to support
VHT NDP in up to 4 STSs. So change the published beamformee
STS cap accordingly to 3 as it should be Nsts-1.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The request of SMPS issued by the Thermal Throttling code
was not reset when we disassociated - fix that.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
It's a bit strange to treat an array as a pointer, so use proper
array indexing instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If the length isn't set it means we want all the SRAM.
Also - this is perfectly valid to partially dump starting
at offset 0.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Discovered by klocwork
Array 'iwl_rate_mcs' of size 15 may use index value(s) -1
* rs.c:2562: index = iwl_hwrate_to_plcp_idx(rate)
* rs.c:2562: Result of function call 'iwl_hwrate_to_plcp_idx(rate)' is '[-1,14]'
* rs.c:2565: Array 'iwl_rate_mcs' size is 15.
* rs.c:2565: Possible attempt to access element -1 of array 'iwl_rate_mcs'.
While at it stop using index = -1 and always use IWL_RATE_INVALID
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Some NIC comes with more than the 4 NVM (non volative
memory) sections described in the nvm_to_read array.
These NICs usually get their NVM from an external file
fetched from userland during init.
We already parsed the file, but sent to the NIC only 4 NVM
sections whereas there could be more sections in the file.
Fix this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since seq_number is incremented right after using
it, so printed seq_ctrl was actually the next
one to be used.
Fix it by incrementing the seq_number only later,
before saving it.
Additionally, use the IEEE80211_SEQ_TO_SN macro
in order to print the actual sequence number.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enabling the oscillator consumes slightly more power (100uA)
but allows to make sure that we exit from L1 on time.
Not doing so might lead to a PCIe specification violation
since we might wake up from L1 at the wrong time.
This issue has been identified on 3160 and 7260 only.
On older NICs L1 off is not enabled, on newer NICs (7265),
the issue is fixed.
When the bug occurs the user sees that the NIC has
disappeared from the PCI bridge, any access to the device
returns 0xff.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=64541
and has been extensively discussed here:
http://markmail.org/thread/mfmpzqt3r333n4bo
Cc: stable@vger.kernel.org [3.10+]
Fixes: 99cd471423 ("iwlwifi: add 7000 series device configuration")
Reported-and-tested-by: wzyboy <wzyboy@wzyboy.org>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fix a bunch of whole lot of namespace issues with the Broadcom bnx2x driver
found by running 'make namespacecheck'
* global variables must be prefixed with bnx2x_
naming a variable int_mode, or num_queue is invitation to disaster
* make local functions static
* move some inline's used in one file out of header
(this driver has a bad case of inline-itis)
* remove resulting dead code fallout
bnx2x_pfc_statistic,
bnx2x_emac_get_pfc_stat
bnx2x_init_vlan_mac_obj,
Looks like vlan mac support in this driver was a botch from day one
either never worked, or not implemented or missing support functions
Compile tested only.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If used 64 bit compiler GCC warns that:
drivers/net/ethernet/smsc/smc91x.c:1897:7:
warning: cast from pointer to integer of different
size [-Wpointer-to-int-cast]
This patch fixes this by changing typecast from "unsigned int" to "unsigned long"
CC: "David S. Miller" <davem@davemloft.net>
CC: Jingoo Han <jg1.han@samsung.com>
CC: netdev@vger.kernel.org
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to clamp_t() first truncates the variable signed 8 bit and as a
result, the actual clamp is a no-op.
Fixes: 0d78156eef ('p54: improve site survey')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Delete a variable that is at most only assigned to a constant, but never
used otherwise.
A simplified version of the semantic patch that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
identifier i;
constant c;
@@
-T i;
<... when != i
-i = c;
...>
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Global Transmission Timeout interrupts are generated by
the HW when transmission of a frame fails - this is done
based on the threshold programmed in the AR_GTXTO register.
Currently, even though the interrupt is enabled for all chips,
it is not handled in the driver. This patch handles GTT events
for AR9003 and above chips, checking if the MAC/BB has hung
after successive GTT interrupts crosses a threshold (5).
This can be enabled for the older chips in the AR9002 family once
appropriate HW hang checks are implemented for them.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to do this and we can avoid
an unused variable warning when CONFIG_ATH9K_WOW is
not selected.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This would be useful when debugging RX performance issues.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, rename node_stat to node_aggr.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The asyncronous firmware load uses a completion struct to hold firmware
processing until the user-space routines are up and running. There is.
however, a problem in that the waiter is nevered canceled during teardown.
As a result, unloading the driver when firmware is not available causes an oops.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The asyncronous firmware load uses a completion struct to hold firmware
processing until the user-space routines are up and running. There is.
however, a problem in that the waiter is nevered canceled during teardown.
As a result, unloading the driver when firmware is not available causes an oops.
To be able to access the completion structure at teardown, it had to be moved
into the b43_wldev structure.
This patch also fixes a typo in a comment.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In https://bugzilla.kernel.org/show_bug.cgi?id=67561, a locking dependency is reported
when b43 is used with hostapd, and rfkill is used to kill the radio output.
The lockdep splat (in part) is as follows:
======================================================
[ INFO: possible circular locking dependency detected ]
3.12.0 #1 Not tainted
-------------------------------------------------------
rfkill/10040 is trying to acquire lock:
(rtnl_mutex){+.+.+.}, at: [<ffffffff8146f282>] rtnl_lock+0x12/0x20
but task is already holding lock:
(rfkill_global_mutex){+.+.+.}, at: [<ffffffffa04832ca>] rfkill_fop_write+0x6a/0x170 [rfkill]
--snip--
Chain exists of:
rtnl_mutex --> misc_mtx --> rfkill_global_mutex
The fix is to move the initialization of the hardware random number generator
outside the code range covered by the rtnl_mutex.
Reported-by: yury <urykhy@gmail.com>
Tested-by: yury <urykhy@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is u64 data received from firmware. Little endian to cpu
conversion is required here.
Cc: <stable@vger.kernel.org> # 3.5+
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver ignores BSS_CHANGED_TXPOWER changes.
Fix this by calling ACX_TX_POWER when appropriate.
Signed-off-by: Alex Gal <a.gal@motsai.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding new device IDs and assigning generic function/variable
names instead of using device-id specific names.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Jan Prinsloo <janroot@gmail.com>
Tested-by: Jan Prinsloo <janroot@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The REGULATORY_CUSTOM_REG can be used during early init with
the goal of overriding the wiphy's default regulatory settings
in case the alpha2 of the device is not known. In the case that
the alpha2 becomes known lets avoid having drivers having to
clear the REGULATORY_CUSTOM_REG flag by doing it for them
when regulatory_hint() is used.
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath wants to first apply the custom regd and only later
will it revert to not using it if an alpha2 regulatory
domain is found. Since the wireless core now enforces
usage of the REGULATORY_CUSTOM_REG strictly when
wiphy_apply_custom_regulatory() is used this makes
ath adhere to the expected behaviour but also updates
the wiphy after its done with the custom usage.
This fixes this warning:
[ 5.488733] ath: phy0: ASPM enabled: 0x43
[ 5.488735] ath: EEPROM regdomain: 0x0
[ 5.488736] ath: EEPROM indicates default country code should be used
[ 5.488736] ath: doing EEPROM country->regdmn map search
[ 5.488737] ath: country maps to regdmn code: 0x3a
[ 5.488737] ath: Country alpha2 being used: US
[ 5.488738] ath: Regpair used: 0x3a
[ 5.488738] ------------[ cut here ]------------
[ 5.488745] WARNING: CPU: 0 PID: 161 at
/home/sujith/dev/wireless-testing/net/wireless/reg.c:1361
wiphy_apply_custom_regulatory+0x17a/0x1b0 [cfg80211]()
[ 5.488746] wiphy should have REGULATORY_CUSTOM_REG
The wireless core can *later* lift this flag for us for when
using the regulatory_hint() to make this fix more generic.
Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to use the native GRO handling of encapsulated protocols on
mlx4, we need to call napi_gro_receive() instead of netif_receive_skb()
unless busy polling is in action.
While we are at it, rename mlx4_en_cq_ll_polling() to
mlx4_en_cq_busy_polling()
Tested with GRE tunnel : GRO aggregation is now performed on the
ethernet device instead of being done later on gre device.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Amir Vadai <amirv@mellanox.com>
Cc: Jerry Chu <hkchu@google.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmalloc is a limited resource. Don't use it unnecessarily.
It seems this allocation should work with kcalloc.
Remove unnecessary memset(,0,) of buf as it's completely
overwritten as the previously only unset field in
struct qlcnic_pci_func_cfg is now set to 0.
Use kfree instead of vfree.
Use ETH_ALEN instead of 6.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I don't know how large "tp->vlan_shift" is but static checkers worry
about shift wrapping bugs here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we disassociate in managed mode, we flush the queues
after mac80211 has already removed the station.
During that time, the pointer to ieee80211_sta to the
fw_id_to_mac_id map is -EINVAL. In that case we should not
set the station as being drained when the last Tx of this
station has exited the shared Tx queue since we are
flushing all the queues anyway.
The draining logic is meant to be used in GO / AP mode only.
In GO / AP mode, we set -EBUSY in the fw_id_to_mac_id map.
This is why testing the ieee80211_sta pointer in the
fw_id_to_mac_id map with IS_ERR isn't enough to set the
station as draining, we need to check that it is -EBUSY.
The only impact of the bug was a print:
Drained sta 1, but it is internal?
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
If we can't switch to a column because no rates are supported
in that column this led to a state where the search cycle
got stuck and never ended. This in turn also led to aggregation
not being turned on. Fix this by marking a column as
visited if we can't switch to it.
Reported-and-tested-by: Karl Beldan <karl.beldan@gmail.com>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cleanup of iwl_mvm_leds was missing in case of error,
resulting in the following warning:
WARNING: at lib/kobject.c:196 kobject_add_internal+0x1f4/0x210()
kobject_add_internal failed for phy0-led with -EEXIST, don't try to register things with the same name in the same directory.
which prevents further reloads of the driver.
Cc: stable@vger.kernel.org [3.10+]
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The power settings need to be updated after a binding flow is done
and before quota calculations. This was missing in the start_ap_ibss()
flow. Fix it.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The state variable was not set to false in case of a failure to
complete the start_ap_ibss() flow.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
That code has been around for ages without being used.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's a huge mess currently, that is really hard to read. This cleanup
doesn't touch the logic at all, it only breaks easy-to-fix long lines and
updates comment styles.
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to i40e and now i40evf.
Most notable is Jacob's patch to add PTP support to i40e.
Mitch cleans up additional memcpy's and use struct assignment instead.
Then fixes long lines to appease checkpatch.pl. Mitch then provides
a fix to keep us from spamming the log with confusing errors. If you
use ip to change the MAC address of a VF while the VF driver is loaded,
closing the VF interface or unloading the VF driver will cause the VF
driver to remove the MAC filter for its original (now invalid) MAC
address.
Jesse cleans up macros which are no longer needed or used.
I (Jeff) cleanup function header comments to ensure Doxygen/kdoc works
correctly to generate documentation without warnings.
Anjali fixes a bug where ethtool set-channels would return failure when
configuring only one Rx queue. Then fixes a bug where the driver was
erroneously exiting the driver unload path if one part of the unload
failed.
Shannon fixes if the IPV6EXADD but is set in the Rx descriptor status,
there was an optional extension header with an alternate IP address
detected and the hardware checksum was not handling the alternate IP
address correctly. Then adjusts the ITR max and min values to match
the hardware max value and recommended min value. Shannon makes sure
to clear the PXE mode after the adminq is initialized.
v2:
- fix patch 14 "i40e: enable PTP" to address Richard Cochran's spelling
catch and Ben Hutchings Kconfig, SIOCGHWTSTAMP and sizeof() suggestions
- added Paul Gortmaker's i40evf fix patch
v3:
- fix patch 14 "i40e: enable PTP" to address Ben Hutchings concerns about
a race with PTP init and cleanup and i40e_get_ts_info().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following sparse warning, which occurs in casts when
accessing the data in the CAN frames (struct can_frame) in the RX and TX
routines:
drivers/net/can/ti_hecc.c:521:17: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:521:17: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:521:17: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:521:17: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:521:17: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:521:17: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:524:25: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:524:25: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:524:25: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:524:25: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:524:25: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:524:25: warning: cast to restricted __be32
drivers/net/can/ti_hecc.c:572:28: warning: incorrect type in assignment (different base types)
drivers/net/can/ti_hecc.c:572:28: expected unsigned int [unsigned] [usertype] <noident>
drivers/net/can/ti_hecc.c:572:28: got restricted __be32 [usertype] <noident>
drivers/net/can/ti_hecc.c:575:40: warning: incorrect type in assignment (different base types)
drivers/net/can/ti_hecc.c:575:40: expected unsigned int [unsigned] [usertype] <noident>
drivers/net/can/ti_hecc.c:575:40: got restricted __be32 [usertype] <noident>
As the data is indeed big endian, use "__be32" instead of "u32", when casting
it.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Building arm:allmodconfig fails with
flexcan.c: In function 'flexcan_read':
flexcan.c:243:2: error: implicit declaration of function 'in_be32'
flexcan.c: In function 'flexcan_write':
flexcan.c:248:2: error: implicit declaration of function 'out_be32'
in_be32 and out_be32 do not (or no longer) exist for ARM targets.
Disable the build for ARM on big endian CPUs.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds support for Elcus CAN200PCI card.
Signed-off-by: Oleg Moroz <oleg.moroz@mcc.vniiem.ru>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
As of commit 7f12ad741a ("i40evf: transmit
and receive functionality") the s390 builds (allyesconfig) fail with:
drivers/net/ethernet/intel/i40evf/i40e_txrx.c: In function 'i40e_clean_rx_irq':
drivers/net/ethernet/intel/i40evf/i40e_txrx.c:818:3: error: implicit declaration of function 'prefetch'
make[5]: *** [drivers/net/ethernet/intel/i40evf/i40e_txrx.o] Error 1
due to an implicit assumption that the prototype from linux/prefetch.h
will be present.
Cc: Mitch Williams <mitch.a.williams@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update the driver version to 0.3.28-k.
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
New feature: Enable PTP support in the i40e driver.
Change-ID: I6a8e799f582705191f9583afb1b9231a8db96cc8
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the latest firmware the clear_pxe_mode function will use the
AdminQ request, so call this after AdminQ is set up rather than
relying on i40e_pf_reset() to clear the PXE mode.
Change-ID: Ice8cba2e9cbc3c7bde0a0bcf8eaf5009abef040b
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure the "new" qtx_head[q] register is cleared before
enabling the Tx queue.
Change-ID: I0c7a12815e343a5ae68807af172a35d6c6857935
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set the ITR max and min values to match the hardware max value
and the recommended min value. These values are shifted right
one bit because the register counts in 2 usec units, so leave
a comment to explain.
Change-ID: I289c27955cf6c566a6d21b95c3110b88cbb15dad
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the IPV6EXADD bit is set in the Rx descriptor status, there
was an optional extension header with an alternate IP address
detected. The HW checksum offload doesn't handle the alternate
IP address correctly so likely comes up with the wrong answer.
Thus, if the bit is set we ignore the checksum offload value.
Change-ID: I70ff8d38cdcddccf44107691cae13d0c07c284c8
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If you use ip to change the MAC address of a VF while the VF
driver is loaded, closing the VF interface or unloading the VF
driver will cause the VF driver to remove the MAC filter for its
original (now invalid) MAC address. This would cause the PF
driver to kick an error message to the log, and back to the VF
driver.
Since the VF driver has not really done anything naughty, let's
not punish it. Don't check for MAC address overrides on the
delete operation, just make sure it's a valid address. This keeps
us from spamming the log with confusing errors.
Change-ID: I1f051bd4014e50855457d928c9ee8b0766981b2f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a bug where the driver was erroneously exiting the driver unload
path if one part of the unload failed. Instead of the original way
the driver should always continue when disabling and be sure to disable
all queues.
Change-ID: Ib8c81c596bc87c31d8e9ca97ebf871168475279d
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix a bug where ethtool set-channels would return failure when configuring
only one Rx queue.
Change-ID: Id833c48c17d71e352b30f3249f6acf9e7aaec57e
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These changes make Doxygen/kdoc work correctly without warnings.
Change-ID: I2941f38860be805ff7548d84dae35754c83f1d62
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
The current driver will warn the user if the NVM version
is out of date, this raises the bar to a newer version.
Change-ID: I5ec21d8efa4e7c3fdacb56f85d310bb2229b1483
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A previous commit removed any need for these macros, so remove
them too.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These instances were found by coccinelle/spatch, and can
use struct assignment instead of memcpy.
Change-ID: Idc23c3599241bf8a658bda18c80417af3fbfee66
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Restore the original regulatory testing functionality and also
make it more flexible by allowing the parameters to be specified
when creating a dynamic radio.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add new commands to the hwsim generic netlink family to allow
creating and destroying radios on the fly. The number of channels
a radio supports can be specified when it's created, if it isn't
the module parameter will be used as default.
This should be extended in the future to allow other parameters
to be specified, e.g.
* list of channels
* interface combinations, particularly P2P_DEVICE support
* regtest
* and pretty much all other hardware capabilities
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reject wmediumd registrations when any devices have multi-channel
capability, but register the generic netlink family unconditionally
to make it possible to add new commands that shouldn't depend on
the number of (default) channels.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There can't be two wmediumd instances controlling hwsim,
so reject registration from a second one and verify in
the commands that it's the correct instance calling.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will make the next patch, adding support for netlink,
smaller and more readable. The code is not modified here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To later allow dynamic registration, assign the index for the
struct device and MAC address from a new free-running counter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Check the flag that the module parameter sets instead, so
later radios can use different parameters.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Jacob Keller