cfg80211 recently gained the ability to understand a
frequency offset component in KHz. Expose this in nl80211
through the new attributes NL80211_ATTR_WIPHY_FREQ_OFFSET,
NL80211_FREQUENCY_ATTR_OFFSET,
NL80211_ATTR_CENTER_FREQ1_OFFSET, and
NL80211_BSS_FREQUENCY_OFFSET.
These add support to send and receive a KHz offset
component with the following NL80211 commands:
- NL80211_CMD_FRAME
- NL80211_CMD_GET_SCAN
- NL80211_CMD_AUTHENTICATE
- NL80211_CMD_ASSOCIATE
- NL80211_CMD_CONNECT
Along with any other command which takes a chandef, ie:
- NL80211_CMD_SET_CHANNEL
- NL80211_CMD_SET_WIPHY
- NL80211_CMD_START_AP
- NL80211_CMD_RADAR_DETECT
- NL80211_CMD_NOTIFY_RADAR
- NL80211_CMD_CHANNEL_SWITCH
- NL80211_JOIN_IBSS
- NL80211_CMD_REMAIN_ON_CHANNEL
- NL80211_CMD_JOIN_OCB
- NL80211_CMD_JOIN_MESH
- NL80211_CMD_TDLS_CHANNEL_SWITCH
If the driver advertises a band containing channels with
frequency offset, it must also verify support for
frequency offset channels in its cfg80211 ops, or return
an error.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200430172554.18383-3-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers may wish to report the RX frequency in units of
KHz. Provide cfg80211_rx_mgmt_khz() and wrap it with
cfg80211_rx_mgmt() so exisiting drivers which can't report
KHz anyway don't need to change. Add a similar wrapper for
cfg80211_report_obss_beacon() so the frequency units stay
somewhat consistent.
This doesn't actually change the nl80211 API yet.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200430172554.18383-2-thomas@adapt-ip.com
[fix mac80211 calling the non-khz version of obss beacon report,
drop trace point name changes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Current rule for applying TID configuration for specific peer looks overly
complicated. No need to reject new TID configuration when override flag is
specified. Another call with the same TID configuration, but without
override flag, allows to apply new configuration anyway.
Use the same approach as for the 'all peers' case: if override flag is
specified, then reset existing TID configuration and immediately
apply a new one.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200424112905.26770-5-sergey.matyukevich.os@quantenna.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
-----BEGIN PGP SIGNATURE-----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=MVBJ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-04-25' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
One batch of changes, containing:
* hwsim improvements from Jouni and myself, to be able to
test more scenarios easily
* some more HE (802.11ax) support
* some initial S1G (sub 1 GHz) work for fractional MHz channels
* some (action) frame registration updates to help DPP support
* along with other various improvements/fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing the "if (IS_ERR(dir)) dir = NULL;" check only works
if we adjust the remaining code to not rely on it being NULL.
Check IS_ERR_OR_NULL() before attempting to dereference it.
I'm not actually entirely sure this fixes the syzbot crash as
the kernel config indicates that they do have DEBUG_FS in the
kernel, but this is what I found when looking there.
Cc: stable@vger.kernel.org
Fixes: d82574a8e5 ("cfg80211: no need to check return value of debugfs_create functions")
Reported-by: syzbot+fd5332e429401bf42d18@syzkaller.appspotmail.com
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200525113816.fc4da3ec3d4b.Ica63a110679819eaa9fb3bc1b7437d96b1fd187d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use a validation type instead, so we can later expose
the NLA_* values to userspace for policy descriptions.
Some transformations were done with this spatch:
@@
identifier p;
expression X, L, A;
@@
struct nla_policy p[X] = {
[A] =
-{ .type = NLA_EXACT_LEN_WARN, .len = L },
+NLA_POLICY_EXACT_LEN_WARN(L),
...
};
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have limited recursive policy validation to avoid
stack overflows, change nl80211 to actually link the nested
policy (linking back to itself eventually), which allows some
code cleanups.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust title markup;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some bands (S1G) define channels centered on a non-integer
MHz. Give ieee80211_channel and cfg80211_chan_def a
freq_offset component where the final frequency can be
expressed as:
MHZ_TO_KHZ(chan->center_freq) + chan->freq_offset;
Also provide some helper functions to do the frequency
conversion and test for equality.
Retain the existing interface to frequency and channel
conversion helpers, and expose new ones which handle
frequencies in units of KHz.
Some internal functions (net/wireless/chan.c) pass around
a frequency value. Convert these to units of KHz.
mesh, ibss, wext, etc. are currently ignored.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200402011810.22947-3-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Somehow we missed this for a long time, but similar to the extended
NSS support in VHT capabilities, we need to have this in Operating
Mode notification.
Implement it by
* parsing the 160/80+80 bit there and setting the bandwidth
appropriately
* having callers of ieee80211_get_vht_max_nss() pass in the current
max NSS value as received in the operating mode notification in
order to modify it appropriately depending on the extended NSS
bits.
This updates all drivers that use it, i.e. only iwlwifi/mvm.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200326150855.098483728cfa.I4e8c25d3288441759c2793247197229f0696a37d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For DPP, there's a need to receive multicast action frames,
but many drivers need a special filter configuration for this.
Support announcing from userspace in the management registration
that multicast RX is required, with an extended feature flag if
the driver handles this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200417124013.c46238801048.Ib041d437ce0bff28a0c6d5dc915f68f1d8591002@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Almost all drivers below cfg80211 get the API wrong (except for
cfg80211) and are unable to cope with multiple registrations for
the same frame type, which is valid due to the match filter.
This seems to indicate the API is wrong, and we should maintain
the full information in cfg80211 instead of the drivers.
Change the API to no longer inform the driver about individual
registrations and unregistrations, but rather every time about
the entire state of the entire wiphy and single wdev, whenever
it may have changed. This also simplifies the code in cfg80211
as it no longer has to track exactly what was unregistered and
can free things immediately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200417124300.f47f3828afc8.I7f81ef59c2c5a340d7075fb3c6d0e08e8aeffe07@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extend cfg80211_rx_unprot_mlme_mgmt() to cover indication of unprotected
Beacon frames in addition to the previously used Deauthentication and
Disassociation frames. The Beacon frame case is quite similar, but has
couple of exceptions: this is used both with fully unprotected and also
incorrectly protected frames and there is a rate limit on the events to
avoid unnecessary flooding netlink events in case something goes wrong.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200401142548.6990-1-jouni@codeaurora.org
[add missing kernel-doc]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Here are 3 SPDX patches for 5.7-rc1.
One fixes up the SPDX tag for a single driver, while the other two go
through the tree and add SPDX tags for all of the .gitignore files as
needed.
Nothing too complex, but you will get a merge conflict with your current
tree, that should be trivial to handle (one file modified by two things,
one file deleted.)
All 3 of these have been in linux-next for a while, with no reported
issues other than the merge conflict.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXodg5A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykySQCgy9YDrkz7nWq6v3Gohl6+lW/L+rMAnRM4uTZm
m5AuCzO3Azt9KBi7NL+L
=2Lm5
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here are three SPDX patches for 5.7-rc1.
One fixes up the SPDX tag for a single driver, while the other two go
through the tree and add SPDX tags for all of the .gitignore files as
needed.
Nothing too complex, but you will get a merge conflict with your
current tree, that should be trivial to handle (one file modified by
two things, one file deleted.)
All three of these have been in linux-next for a while, with no
reported issues other than the merge conflict"
* tag 'spdx-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx:
ASoC: MT6660: make spdxcheck.py happy
.gitignore: add SPDX License Identifier
.gitignore: remove too obvious comments
When cfg80211_update_assoc_bss_entry() is called, there is a
verification that the BSS channel actually changed. As some APs use
CSA also for bandwidth changes, this would result with a kernel
warning.
Fix this by removing the WARN_ON().
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200326150855.96316ada0e8d.I6710376b1b4257e5f4712fc7ab16e2b638d512aa@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new opmode notification used this attribute with a u8, when
it's documented as a u32 and indeed used in userspace as such,
it just happens to work on little-endian systems since userspace
isn't doing any strict size validation, and the u8 goes into the
lower byte. Fix this.
Cc: stable@vger.kernel.org
Fixes: 466b9936bf ("cfg80211: Add support to notify station's opmode change to userspace")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200325090531.be124f0a11c7.Iedbf4e197a85471ebd729b186d5365c0343bf7a8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers that trigger roaming need to know the lifetime of the configured
PMKSA for deciding whether to trigger the full or PMKSA cache based
authentication. The configured PMKSA is invalid after the PMK lifetime
has expired and must not be used after that and the STA needs to
disassociate if the PMK expires. Hence the STA is expected to refresh
the PMK with a full authentication before this happens (e.g., when
reassociating to a new BSS the next time or by performing EAPOL
reauthentication depending on the AKM) to avoid unnecessary
disconnection.
The PMK reauthentication threshold is the percentage of the PMK lifetime
value and indicates to the driver to trigger a full authentication roam
(without PMKSA caching) after the reauthentication threshold time, but
before the PMK timer has expired. Authentication methods like SAE need
to be able to generate a new PMKSA entry without having to force a
disconnection after this threshold timeout. If no roaming occurs between
the reauthentication threshold time and PMK lifetime expiration,
disassociation is still forced.
The new attributes for providing these values correspond to the dot11
MIB variables dot11RSNAConfigPMKLifetime and
dot11RSNAConfigPMKReauthThreshold.
This type of functionality is already available in cases where user
space component is in control of roaming. This commit extends that same
capability into cases where parts or all of this functionality is
offloaded to the driver.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200312235903.18462-1-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sometimes, userspace is able to detect that a peer silently lost its
state (like, if the peer reboots). wpa_supplicant does this for IBSS-RSN
by registering for auth/deauth frames, but when it detects this, it is
only able to remove the encryption keys of the peer and close its port.
However, the kernel also hold other state about the station, such as BA
sessions, probe response parameters and the like. They also need to be
resetted correctly.
This patch adds the NL80211_EXT_FEATURE_DEL_IBSS_STA feature flag
indicating the driver accepts deleting stations in IBSS mode, which
should send a deauth and reset the state of the station, just like in
mesh point mode.
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Link: https://lore.kernel.org/r/20200305135754.12094-1-cavallar@lri.fr
[preserve -EINVAL return]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pass the AP's HE operation element to the driver.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-18-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for requesting that the ranging measurement will use
the trigger-based / non trigger-based flow instead of the EDCA based
flow.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-2-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds support for disabling pre-auth rx over the nl80211 control
port for mac80211.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200312091055.54257-3-markus.theil@tu-ilmenau.de
[fix indentation slightly, squash feature enablement]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the nl80211 control port is used before this patch, pre-auth frames
(0x88c7) are send to userspace uncoditionally. While this enables userspace
to only use nl80211 on the station side, it is not always useful for APs.
Furthermore, pre-auth frames are ordinary data frames and not related to
the control port. Therefore it should for example be possible for pre-auth
frames to be bridged onto a wired network on AP side without touching
userspace.
For backwards compatibility to code already using pre-auth over nl80211,
this patch adds a feature flag to disable this behavior, while it remains
enabled by default. An additional ext. feature flag is added to detect this
from userspace.
Thanks to Jouni for pointing out, that pre-auth frames should be handled as
ordinary data frames.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200312091055.54257-2-markus.theil@tu-ilmenau.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add missing attribute validation for beacon report scanning
to the netlink policy.
Fixes: 1d76250bd3 ("nl80211: support beacon report scanning")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20200303051058.4089398-3-kuba@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mptcp conflict was overlapping additions.
The SMC conflict was an additional and removal happening at the same
time.
Signed-off-by: David S. Miller <davem@davemloft.net>
* lots of small documentation fixes, from Jérôme Pouiller
* beacon protection (BIGTK) support from Jouni Malinen
* some initial code for TID configuration, from Tamizh chelvam
* I reverted some new API before it's actually used, because
it's wrong to mix controlled port and preauth
* a few other cleanups/fixes
-----BEGIN PGP SIGNATURE-----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=x0rf
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-02-24' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
A new set of changes:
* lots of small documentation fixes, from Jérôme Pouiller
* beacon protection (BIGTK) support from Jouni Malinen
* some initial code for TID configuration, from Tamizh chelvam
* I reverted some new API before it's actually used, because
it's wrong to mix controlled port and preauth
* a few other cleanups/fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to configure per TID RTSCTS control
configuration to enable/disable through the
NL80211_TID_CONFIG_ATTR_RTSCTS_CTRL attribute.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Link: https://lore.kernel.org/r/1579506687-18296-5-git-send-email-tamizhr@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds support to configure per TID AMPDU control
configuration to enable/disable aggregation through the
NL80211_TID_CONFIG_ATTR_AMPDU_CTRL attribute.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Link: https://lore.kernel.org/r/1579506687-18296-4-git-send-email-tamizhr@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds support to configure per TID retry configuration
through the NL80211_TID_CONFIG_ATTR_RETRY_SHORT and
NL80211_TID_CONFIG_ATTR_RETRY_LONG attributes. This TID specific
retry configuration will have more precedence than phy level
configuration.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Link: https://lore.kernel.org/r/1579506687-18296-3-git-send-email-tamizhr@codeaurora.org
[rebase completely on top of my previous API changes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make some changes to the TID-config API:
* use u16 in nl80211 (only, and restrict to using 8 bits for now),
to avoid issues in the future if we ever want to use higher TIDs.
* reject empty TIDs mask (via netlink policy)
* change feature advertising to not use extended feature flags but
have own mechanism for this, which simplifies the code
* fix all variable names from 'tid' to 'tids' since it's a mask
* change to cfg80211_ name prefixes, not ieee80211_
* fix some minor docs/spelling things.
Change-Id: Ia234d464b3f914cdeab82f540e018855be580dce
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the new NL80211_CMD_SET_TID_CONFIG command to support
data TID specific configuration. Per TID configuration is
passed in the nested NL80211_ATTR_TID_CONFIG attribute.
This patch adds support to configure per TID noack policy
through the NL80211_TID_CONFIG_ATTR_NOACK attribute.
Signed-off-by: Tamizh chelvam <tamizhr@codeaurora.org>
Link: https://lore.kernel.org/r/1579506687-18296-2-git-send-email-tamizhr@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
IEEE P802.11-REVmd/D3.0 adds support for protecting Beacon frames using
a new set of keys (BIGTK; key index 6..7) similarly to the way
group-addressed Robust Management frames are protected (IGTK; key index
4..5). Extend cfg80211 and nl80211 to allow the new BIGTK to be
configured. Add an extended feature flag to indicate driver support for
the new key index values to avoid array overflows in driver
implementations and also to indicate to user space when this
functionality is available.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200222132548.20835-2-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These were helpful while working with extensions to NL80211_CMD_NEW_KEY,
so add more explicit error reporting for additional cases that can fail
while that command is being processed.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200222132548.20835-1-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 8c3ed7aa2b.
As Jouni points out, there's really no need for this, since the
RSN pre-authentication frames are normal data frames, not port
control frames (locally).
We can still revert this now since it hasn't actually gone beyond
-next.
Fixes: 8c3ed7aa2b ("nl80211: add src and dst addr attributes for control port tx/rx")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200224101910.b746e263287a.I9eb15d6895515179d50964dec3550c9dc784bb93@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
rdev->sched_scan_req_list maybe traversed using list_for_each_entry_rcu
outside an RCU read-side critical section but under the protection
of rtnl_mutex.
Hence, add corresponding lockdep expression to silence false-positive
warnings, and harden RCU lists.
Signed-off-by: Amol Grover <frextrite@gmail.com>
Link: https://lore.kernel.org/r/20200219091102.10709-1-frextrite@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Trivial cleanup, so that all bridge port-specific code can be found in
one go.
CC: Johannes Berg <johannes@sipsolutions.net>
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 802.11 frame encapsulation offload support
* more HE (802.11ax) support, including some for 6 GHz band
* powersave in hwsim, for better testing
Of course as usual there are various cleanups and small fixes.
-----BEGIN PGP SIGNATURE-----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=CgmJ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-02-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
A few big new things:
* 802.11 frame encapsulation offload support
* more HE (802.11ax) support, including some for 6 GHz band
* powersave in hwsim, for better testing
Of course as usual there are various cleanups and small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The nl80211_policy is missing for NL80211_ATTR_STATUS_CODE attribute.
As a result, for strictly validated commands, it's assumed to not be
supported.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200213131608.10541-2-sergey.matyukevich.os@quantenna.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When using control port over nl80211 in AP mode with
pre-authentication, APs need to forward frames to other
APs defined by their MAC address. Before this patch,
pre-auth frames reaching user space over nl80211 control
port have no longer any information about the dest attached,
which can be used for forwarding to a controller or injecting
the frame back to a ethernet interface over a AF_PACKET
socket.
Analog problems exist, when forwarding pre-auth frames from
AP -> STA.
This patch therefore adds the NL80211_ATTR_DST_MAC and
NL80211_ATTR_SRC_MAC attributes to provide more context
information when forwarding.
The respective arguments are optional on tx and included on rx.
Therefore unaware existing software is not affected.
Software which wants to detect this feature, can do so
by checking against:
NL80211_EXT_FEATURE_CONTROL_PORT_OVER_NL80211_MAC_ADDRS
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200115125522.3755-1-markus.theil@tu-ilmenau.de
[split into separate cfg80211/mac80211 patches]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To support Pre Association Security Negotiation (PASN) while already
associated to one AP, allow user space to register to Rx
authentication frames, so that the user space logic would be able to
receive/handle authentication frames from a different AP as part of
PASN.
Note that it is expected that user space would intelligently register
for Rx authentication frames, i.e., only when PASN is used and
configure a match filter only for PASN authentication algorithm, as
otherwise the MLME functionality of mac80211 would be broken.
Additionally, since some versions of the user space daemons wrongly
register to all types of authentication frames (which might result in
unexpected behavior) allow such registration if the request is for a
specific authentication algorithm number.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131114529.894206-1-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When preparing ethtool drvinfo, check if wiphy driver is defined
before dereferencing it. Driver may not exist, e.g. if wiphy is
attached to a virtual platform device.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20200203105644.28875-1-sergey.matyukevich.os@quantenna.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit ab4dfa2053 ("cfg80211: Allow drivers to advertise supported AKM
suites") introduces the support to advertize supported AKMs to userspace.
This needs an enhancement to advertize the AKM support per interface type,
specifically for the cfg80211-based drivers that implement SME and use
different mechanisms to support the AKM's for each interface type (e.g.,
the support for SAE, OWE AKM's take different paths for such drivers on
STA/AP mode).
This commit aims the same and enhances the earlier mechanism of advertizing
the AKMs per wiphy. Add new nl80211 attributes and data structure to
provide supported AKMs per interface type to userspace.
the AKMs advertized in akm_suites are default capabilities if not
advertized for a specific interface type in iftype_akm_suites.
Signed-off-by: Veerendranath Jakkam <vjakkam@codeaurora.org>
Link: https://lore.kernel.org/r/20200126203032.21934-1-vjakkam@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The regulatory domain might forbid HE operation. Certain regulatory
domains may restrict it for specific channels whereas others may do it
for the whole regulatory domain.
Add an option to indicate it in the channel flag.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200121081213.733757-1-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking updates from David Miller:
1) Add WireGuard
2) Add HE and TWT support to ath11k driver, from John Crispin.
3) Add ESP in TCP encapsulation support, from Sabrina Dubroca.
4) Add variable window congestion control to TIPC, from Jon Maloy.
5) Add BCM84881 PHY driver, from Russell King.
6) Start adding netlink support for ethtool operations, from Michal
Kubecek.
7) Add XDP drop and TX action support to ena driver, from Sameeh
Jubran.
8) Add new ipv4 route notifications so that mlxsw driver does not have
to handle identical routes itself. From Ido Schimmel.
9) Add BPF dynamic program extensions, from Alexei Starovoitov.
10) Support RX and TX timestamping in igc, from Vinicius Costa Gomes.
11) Add support for macsec HW offloading, from Antoine Tenart.
12) Add initial support for MPTCP protocol, from Christoph Paasch,
Matthieu Baerts, Florian Westphal, Peter Krystad, and many others.
13) Add Octeontx2 PF support, from Sunil Goutham, Geetha sowjanya, Linu
Cherian, and others.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1469 commits)
net: phy: add default ARCH_BCM_IPROC for MDIO_BCM_IPROC
udp: segment looped gso packets correctly
netem: change mailing list
qed: FW 8.42.2.0 debug features
qed: rt init valid initialization changed
qed: Debug feature: ilt and mdump
qed: FW 8.42.2.0 Add fw overlay feature
qed: FW 8.42.2.0 HSI changes
qed: FW 8.42.2.0 iscsi/fcoe changes
qed: Add abstraction for different hsi values per chip
qed: FW 8.42.2.0 Additional ll2 type
qed: Use dmae to write to widebus registers in fw_funcs
qed: FW 8.42.2.0 Parser offsets modified
qed: FW 8.42.2.0 Queue Manager changes
qed: FW 8.42.2.0 Expose new registers and change windows
qed: FW 8.42.2.0 Internal ram offsets modifications
MAINTAINERS: Add entry for Marvell OcteonTX2 Physical Function driver
Documentation: net: octeontx2: Add RVU HW and drivers overview
octeontx2-pf: ethtool RSS config support
octeontx2-pf: Add basic ethtool support
...
This patch adds the attributes, policy and parsing code to allow userland
to send the info about the BSS coloring settings to the kernel.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20191217141921.8114-1-john@phrozen.org
[johannes: remove the strict policy parsing, that was a misunderstanding]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The fragments attached to a skb can be part of a compound page. In that case,
page_ref_inc will increment the refcount for the wrong page. Fix this by
using get_page instead, which calls page_ref_inc on the compound head and
also checks for overflow.
Fixes: 2b67f944f8 ("cfg80211: reuse existing page fragments in A-MSDU rx")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200113182107.20461-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After the introduction of CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE_O3,
the wext code produces a bogus warning:
In function 'iw_handler_get_iwstats',
inlined from 'ioctl_standard_call' at net/wireless/wext-core.c:1015:9,
inlined from 'wireless_process_ioctl' at net/wireless/wext-core.c:935:10,
inlined from 'wext_ioctl_dispatch.part.8' at net/wireless/wext-core.c:986:8,
inlined from 'wext_handle_ioctl':
net/wireless/wext-core.c:671:3: error: argument 1 null where non-null expected [-Werror=nonnull]
memcpy(extra, stats, sizeof(struct iw_statistics));
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from arch/x86/include/asm/string.h:5,
net/wireless/wext-core.c: In function 'wext_handle_ioctl':
arch/x86/include/asm/string_64.h:14:14: note: in a call to function 'memcpy' declared here
The problem is that ioctl_standard_call() sometimes calls the handler
with a NULL argument that would cause a problem for iw_handler_get_iwstats.
However, iw_handler_get_iwstats never actually gets called that way.
Marking that function as noinline avoids the warning and leads
to slightly smaller object code as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20200107200741.3588770-1-arnd@arndb.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case a radar event of CAC_FINISHED or RADAR_DETECTED
happens during another phy is during CAC we might need
to cancel that CAC.
If we got a radar in a channel that another phy is now
doing CAC on then the CAC should be canceled there.
If, for example, 2 phys doing CAC on the same channels,
or on comptable channels, once on of them will finish his
CAC the other might need to cancel his CAC, since it is no
longer relevant.
To fix that the commit adds an callback and implement it in
mac80211 to end CAC.
This commit also adds a call to said callback if after a radar
event we see the CAC is no longer relevant
Signed-off-by: Orr Mazor <Orr.Mazor@tandemg.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20191222145449.15792-1-Orr.Mazor@tandemg.com
[slightly reformat/reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit e33e2241e2 ("Revert "cfg80211: Use 5MHz bandwidth by
default when checking usable channels"") fixed a broken
regulatory (leaving channel 12 open for AP where not permitted).
Apply a similar fix to custom regulatory domain processing.
Signed-off-by: Cathy Luo <xiaohua.luo@nxp.com>
Signed-off-by: Ganapathi Bhat <ganapathi.bhat@nxp.com>
Link: https://lore.kernel.org/r/1576836859-8945-1-git-send-email-ganapathi.bhat@nxp.com
[reword commit message, fix coding style, add a comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If wdev->wext.keys was initialized it didn't get reset to NULL on
unregister (and it doesn't get set in cfg80211_init_wdev either), but
wdev is reused if unregister was triggered through
cfg80211_switch_netns.
The next unregister (for whatever reason) will try to free
wdev->wext.keys again.
Signed-off-by: Stefan Bühler <source@stbuehler.de>
Link: https://lore.kernel.org/r/20191126100543.782023-1-stefan.buehler@tik.uni-stuttgart.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Function nl80211_validate_nested() is not specific to nl80211, it's
a counterpart to nla_validate_nested_deprecated() with strict validation.
For consistency with other validation and parse functions, rename it to
nla_validate_nested().
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework event_create_dir() to use an array of static data instead of
function pointers where possible.
The problem is that it would call the function pointer on module load
before parse_args(), possibly even before jump_labels were initialized.
Luckily the generated functions don't use jump_labels but it still seems
fragile. It also gets in the way of changing when we make the module map
executable.
The generated function are basically calling trace_define_field() with a
bunch of static arguments. So instead of a function, capture these
arguments in a static array, avoiding the function call.
Now there are a number of cases where the fields are dynamic (syscall
arguments, kprobes and uprobes), in which case a static array does not
work, for these we preserve the function call. Luckily all these cases
are not related to modules and so we can retain the function call for
them.
Also fix up all broken tracepoint definitions that now generate a
compile error.
Tested-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20191111132458.342979914@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
* typo fixes in docs
* APIs for station separation using VLAN tags rather
than separate wifi netdevs
* some preparations for upcoming features (802.3 offload
and airtime queue limits (AQL)
* stack reduction in ieee80211_assoc_success()
* use DEFINE_DEBUGFS_ATTRIBUTE in hwsim
-----BEGIN PGP SIGNATURE-----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=gDUI
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2019-11-08' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Some relatively small changes:
* typo fixes in docs
* APIs for station separation using VLAN tags rather
than separate wifi netdevs
* some preparations for upcoming features (802.3 offload
and airtime queue limits (AQL)
* stack reduction in ieee80211_assoc_success()
* use DEFINE_DEBUGFS_ATTRIBUTE in hwsim
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides an alternative mechanism for AP VLAN support where a
single netdev is used with VLAN tagged frames instead of separate
netdevs for each VLAN without tagged frames from the WLAN driver.
By setting NL80211_EXT_FEATURE_VLAN_OFFLOAD flag the driver indicates
support for a single netdev with VLAN tagged frames. Separate
VLAN-specific netdevs can be added using RTM_NEWLINK/IFLA_VLAN_ID
similarly to Ethernet. NL80211_CMD_NEW_KEY (for group keys),
NL80211_CMD_NEW_STATION, and NL80211_CMD_SET_STATION will optionally
specify vlan_id using NL80211_ATTR_VLAN_ID.
Signed-off-by: Gurumoorthi Gnanasambandhan <gguru@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20191031214640.5012-1-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch disables setting of HT20 and more for channel 14 because
the channel is only for IEEE 802.11b.
The patch for net/wireless/util.c was unit-tested.
The patch for net/wireless/chan.c was tested with iw command.
Before this patch.
$ sudo iw dev <ifname> set channel 14 HT20
$
After this patch.
$ sudo iw dev <ifname> set channel 14 HT20
kernel reports: invalid channel definition
command failed: Invalid argument (-22)
$
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Link: https://lore.kernel.org/r/20191021075045.2719-1-masashi.honma@gmail.com
[clean up the code, use != instead of equivalent >]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix misspellings of "disconnect", "disconnecting", "connections", and
"disconnected".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
* minstrel improvements from Felix
* a TX aggregation simplification
* some additional capabilities for hwsim
* minor cleanups & docs updates
-----BEGIN PGP SIGNATURE-----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=IJ7D
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2019-10-11' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
A few more small things, nothing really stands out:
* minstrel improvements from Felix
* a TX aggregation simplification
* some additional capabilities for hwsim
* minor cleanups & docs updates
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
cfg80211_assign_cookie already checks & prevents a 0 from being
returned, so the explicit loop is unnecessary.
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Link: https://lore.kernel.org/r/20191008164350.2836-1-denkenz@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In non-ETSI regulatory domains scan is blocked when operating channel
is a DFS channel. For ETSI, however, once DFS channel is marked as
available after the CAC, this channel will remain available (for some
time) even after leaving this channel.
Therefore a scan can be done without any impact on the availability
of the DFS channel as no new CAC is required after the scan.
Enable scan in mac80211 in these cases.
Signed-off-by: Aaron Komisar <aaron.komisar@tandemg.com>
Link: https://lore.kernel.org/r/1570024728-17284-1-git-send-email-aaron.komisar@tandemg.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_update_notlisted_nontrans() leaves the RCU critical session
too early, while still using nontrans_ssid which is RCU protected. In
addition, it performs a bunch of RCU pointer update operations such
as rcu_access_pointer and rcu_assign_pointer.
The caller, cfg80211_inform_bss_frame_data(), also accesses the RCU
pointer without holding the lock.
Just wrap all of this with bss_lock.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20191004123706.15768-3-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In nl80211_get_ftm_responder_stats, a new skb is created via nlmsg_new
named msg. If nl80211hdr_put() fails, then msg should be released. The
return statement should be replace by goto to error handling code.
Fixes: 81e54d08d9 ("cfg80211: support FTM responder configuration/statistics")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Link: https://lore.kernel.org/r/20191004194220.19412-1-navid.emamdoost@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ensure the SSID element is bounds-checked prior to invoking memcpy()
with its length field, when copying to userspace.
Cc: <stable@vger.kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Reported-by: Nicolas Waisman <nico@semmle.com>
Signed-off-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20191004095132.15777-2-will@kernel.org
[adjust commit log a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the interface is not in MESH mode, the command 'iw wlanx mpath del'
will cause kernel panic.
The root cause is null pointer access in mpp_flush_by_proxy(), as the
pointer 'sdata->u.mesh.mpp_paths' is NULL for non MESH interface.
Unable to handle kernel NULL pointer dereference at virtual address 00000068
[...]
PC is at _raw_spin_lock_bh+0x20/0x5c
LR is at mesh_path_del+0x1c/0x17c [mac80211]
[...]
Process iw (pid: 4537, stack limit = 0xd83e0238)
[...]
[<c021211c>] (_raw_spin_lock_bh) from [<bf8c7648>] (mesh_path_del+0x1c/0x17c [mac80211])
[<bf8c7648>] (mesh_path_del [mac80211]) from [<bf6cdb7c>] (extack_doit+0x20/0x68 [compat])
[<bf6cdb7c>] (extack_doit [compat]) from [<c05c309c>] (genl_rcv_msg+0x274/0x30c)
[<c05c309c>] (genl_rcv_msg) from [<c05c25d8>] (netlink_rcv_skb+0x58/0xac)
[<c05c25d8>] (netlink_rcv_skb) from [<c05c2e14>] (genl_rcv+0x20/0x34)
[<c05c2e14>] (genl_rcv) from [<c05c1f90>] (netlink_unicast+0x11c/0x204)
[<c05c1f90>] (netlink_unicast) from [<c05c2420>] (netlink_sendmsg+0x30c/0x370)
[<c05c2420>] (netlink_sendmsg) from [<c05886d0>] (sock_sendmsg+0x70/0x84)
[<c05886d0>] (sock_sendmsg) from [<c0589f4c>] (___sys_sendmsg.part.3+0x188/0x228)
[<c0589f4c>] (___sys_sendmsg.part.3) from [<c058add4>] (__sys_sendmsg+0x4c/0x70)
[<c058add4>] (__sys_sendmsg) from [<c0208c80>] (ret_fast_syscall+0x0/0x44)
Code: e2822c02 e2822001 e5832004 f590f000 (e1902f9f)
---[ end trace bbd717600f8f884d ]---
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Link: https://lore.kernel.org/r/1569485810-761-1-git-send-email-miaoqing@codeaurora.org
[trim useless data from commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In a few places we don't properly initialize on-stack chandefs,
resulting in EDMG data to be non-zero, which broke things.
Additionally, in a few places we rely on the driver to init the
data completely, but perhaps we shouldn't as non-EDMG drivers
may not initialize the EDMG data, also initialize it there.
Cc: stable@vger.kernel.org
Fixes: 2a38075cd0 ("nl80211: Add support for EDMG channels")
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/1569239475-I2dcce394ecf873376c386a78f31c2ec8b538fa25@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code copying the data assumes that the SSID element is
before the MBSSID element, but since the data is untrusted
from the AP, this cannot be guaranteed.
Validate that this is indeed the case and ignore the MBSSID
otherwise, to avoid having to deal with both cases for the
copy of data that should be between them.
Cc: stable@vger.kernel.org
Fixes: 0b8fb8235b ("cfg80211: Parsing of Multiple BSSID information in scanning")
Link: https://lore.kernel.org/r/1569009255-I1673911f5eae02964e21bdc11b2bf58e5e207e59@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We currently don't validate the beacon head, i.e. the header,
fixed part and elements that are to go in front of the TIM
element. This means that the variable elements there can be
malformed, e.g. have a length exceeding the buffer size, but
most downstream code from this assumes that this has already
been checked.
Add the necessary checks to the netlink policy.
Cc: stable@vger.kernel.org
Fixes: ed1b6cc7f8 ("cfg80211/nl80211: add beacon settings")
Link: https://lore.kernel.org/r/1569009255-I7ac7fbe9436e9d8733439eab8acbbd35e55c74ef@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* a fix in the new 6 GHz channel support
* a fix for recent minstrel (rate control) updates
for an infinite loop
* handle interface type changes better wrt. management frame
registrations (for management frames sent to userspace)
* add in-BSS RX time to survey information
* handle HW rfkill properly if !CONFIG_RFKILL
* send deauth on IBSS station expiry, to avoid state mismatches
* handle deferred crypto tailroom updates in mac80211 better
when device restart happens
* fix a spectre-v1 - really a continuation of a previous patch
* advertise NL80211_CMD_UPDATE_FT_IES as supported if so
* add some missing parsing in VHT extended NSS support
* support HE in mac80211_hwsim
* let mac80211 drivers determine the max MTU themselves
along with the usual cleanups etc.
-----BEGIN PGP SIGNATURE-----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=HAuT
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2019-09-11' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
We have a number of changes, but things are settling down:
* a fix in the new 6 GHz channel support
* a fix for recent minstrel (rate control) updates
for an infinite loop
* handle interface type changes better wrt. management frame
registrations (for management frames sent to userspace)
* add in-BSS RX time to survey information
* handle HW rfkill properly if !CONFIG_RFKILL
* send deauth on IBSS station expiry, to avoid state mismatches
* handle deferred crypto tailroom updates in mac80211 better
when device restart happens
* fix a spectre-v1 - really a continuation of a previous patch
* advertise NL80211_CMD_UPDATE_FT_IES as supported if so
* add some missing parsing in VHT extended NSS support
* support HE in mac80211_hwsim
* let mac80211 drivers determine the max MTU themselves
along with the usual cleanups etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently frame registrations are not purged, even when changing the
interface type. This can lead to potentially weird situations where
frames possibly not allowed on a given interface type remain registered
due to the type switching happening after registration.
The kernel currently relies on userspace apps to actually purge the
registrations themselves, this is not something that the kernel should
rely on.
Add a call to cfg80211_mlme_purge_registrations() to forcefully remove
any registrations left over prior to switching the iftype.
Cc: stable@vger.kernel.org
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Link: https://lore.kernel.org/r/20190828211110.15005-1-denkenz@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
commit 1222a16014 ("nl80211: Fix possible Spectre-v1 for CQM
RSSI thresholds") was incomplete and requires one more fix to
prevent accessing to rssi_thresholds[n] because user can control
rssi_thresholds[i] values to make i reach to n. For example,
rssi_thresholds = {-400, -300, -200, -100} when last is -34.
Cc: stable@vger.kernel.org
Fixes: 1222a16014 ("nl80211: Fix possible Spectre-v1 for CQM RSSI thresholds")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Link: https://lore.kernel.org/r/20190908005653.17433-1-masashi.honma@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With the help of boolinit.cocci, we use !nl80211_reg_change_event_fill
instead of (nl80211_reg_change_event_fill == false). Meanwhile, Clean
up the code.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Link: https://lore.kernel.org/r/1567657537-65472-1-git-send-email-zhongjiang@huawei.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the RFKILL subsystem isn't available, then rfkill_blocked()
always returns false. In the case of hardware rfkill this will
be wrong though, as if the hardware reported being killed then
it cannot operate any longer.
Since we only ever call the rfkill_sync work in this case, just
rename it to rfkill_block and always pass "true" for the blocked
parameter, rather than passing rfkill_blocked().
We rely on the underlying driver to still reject any new attempt
to bring up the device by itself.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190830112451.21655-2-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The boundary value used for the 6G band was incorrect as it would
result in invalid 6G channel number for certain frequencies.
Reported-by: Amar Singhal <asinghal@codeaurora.org>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1567510772-24263-1-git-send-email-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is useful for checking how much airtime is being used up by other
transmissions on the channel, e.g. by calculating (time_rx - time_bss_rx)
or (time_busy - time_bss_rx - time_tx)
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20190828102042.58016-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add NL80211_CMD_UPDATE_FT_IES to supported commands. In mac80211 drivers,
this can be implemented via existing NL80211_CMD_AUTHENTICATE and
NL80211_ATTR_IE, but non-mac80211 drivers have a separate command for
this. A driver supports FT if it either is mac80211 or supports this
command.
Signed-off-by: Matthew Wang <matthewmwang@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20190822174806.2954-1-matthewmwang@chromium.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
802.11ay specification defines Enhanced Directional Multi-Gigabit
(EDMG) STA and AP which allow channel bonding of 2 channels and more.
Introduce new NL attributes that are needed for enabling and
configuring EDMG support.
Two new attributes are used by kernel to publish driver's EDMG
capabilities to the userspace:
NL80211_BAND_ATTR_EDMG_CHANNELS - bitmap field that indicates the 2.16
GHz channel(s) that are supported by the driver.
When this attribute is not set it means driver does not support EDMG.
NL80211_BAND_ATTR_EDMG_BW_CONFIG - represent the channel bandwidth
configurations supported by the driver.
Additional two new attributes are used by the userspace for connect
command and for AP configuration:
NL80211_ATTR_WIPHY_EDMG_CHANNELS
NL80211_ATTR_WIPHY_EDMG_BW_CONFIG
New rate info flag - RATE_INFO_FLAGS_EDMG, can be reported from driver
and used for bitrate calculation that will take into account EDMG
according to the 802.11ay specification.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Link: https://lore.kernel.org/r/1566138918-3823-2-git-send-email-ailizaro@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For the new 6GHz band the same rules apply for mandatory rates so
add it to set_mandatory_flags_band() function.
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Leon Zegers <leon.zegers@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-9-git-send-email-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The default mandatory rates, ie. when not specified by user-space, is
determined by the band. Select 11a rateset for 6GHz band.
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Leon Zegers <leon.zegers@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-8-git-send-email-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function cfg80211_ir_permissive_chan() is applicable for
6GHz band as well so make sure it is handled.
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Leon Zegers <leon.zegers@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-7-git-send-email-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In nl80211.c there is a policy for all bands in NUM_NL80211_BANDS and
in trace.h there is a callback trace for multicast rates which is per
band in NUM_NL80211_BANDS. Both need to be extended for the new
NL80211_BAND_6GHZ.
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Leon Zegers <leon.zegers@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-6-git-send-email-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add 6GHz operating class range as defined in 802.11ax D4.1 Annex E.
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Leon Zegers <leon.zegers@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-5-git-send-email-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extend the functions ieee80211_channel_to_frequency() and
ieee80211_frequency_to_channel() to support 6GHz band according
specification in 802.11ax D4.1 27.3.22.2.
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Leon Zegers <leon.zegers@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Link: https://lore.kernel.org/r/1564745465-21234-4-git-send-email-arend.vanspriel@broadcom.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 96cce12ff6 ("cfg80211: fix processing world
regdomain when non modular").
Re-triggering a reg_process_hint with the last request on all events,
can make the regulatory domain fail in case of multiple WiFi modules. On
slower boards (espacially with mdev), enumeration of the WiFi modules
can end up in an intersected regulatory domain, and user cannot set it
with 'iw reg set' anymore.
This is happening, because:
- 1st module enumerates, queues up a regulatory request
- request gets processed by __reg_process_hint_driver():
- checks if previous was set by CORE -> yes
- checks if regulator domain changed -> yes, from '00' to e.g. 'US'
-> sends request to the 'crda'
- 2nd module enumerates, queues up a regulator request (which triggers
the reg_todo() work)
- reg_todo() -> reg_process_pending_hints() sees, that the last request
is not processed yet, so it tries to process it again.
__reg_process_hint driver() will run again, and:
- checks if the last request's initiator was the core -> no, it was
the driver (1st WiFi module)
- checks, if the previous initiator was the driver -> yes
- checks if the regulator domain changed -> yes, it was '00' (set by
core, and crda call did not return yet), and should be changed to 'US'
------> __reg_process_hint_driver calls an intersect
Besides, the reg_process_hint call with the last request is meaningless
since the crda call has a timeout work. If that timeout expires, the
first module's request will lost.
Cc: stable@vger.kernel.org
Fixes: 96cce12ff6 ("cfg80211: fix processing world regdomain when non modular")
Signed-off-by: Robert Hodaszi <robert.hodaszi@digi.com>
Link: https://lore.kernel.org/r/20190614131600.GA13897@a1-hr
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix two shortcomings in the Extended Key ID API:
1) Allow the userspace to install pairwise keys using keyid 1 without
NL80211_KEY_NO_TX set. This allows the userspace to install and
activate pairwise keys with keyid 1 in the same way as for keyid 0,
simplifying the API usage for e.g. FILS and FT key installs.
2) IEEE 802.11 - 2016 restricts Extended Key ID usage to CCMP/GCMP
ciphers in IEEE 802.11 - 2016 "9.4.2.25.4 RSN capabilities".
Enforce that when installing a key.
Cc: stable@vger.kernel.org # 5.2
Fixes: 6cdd3979a2 ("nl80211/cfg80211: Extended Key ID support")
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Link: https://lore.kernel.org/r/20190805123400.51567-1-alexander@wetzel-home.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a strict start type so all new attributes starting from
NL80211_ATTR_HE_OBSS_PD are validated strictly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the data structure, policy and parsing code allowing userland to send
the OBSS PD information into the kernel.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190730163701.18836-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Over time, we really need to get rid of all of our global locking.
One of the things needed is to use parallel_ops. This isn't really
the most important (RTNL is much more important) but OTOH we just
keep adding uses of genl_family_attrbuf() now. Use .parallel_ops to
disallow this.
Reviewed-By: Denis Kenzior <denkenz@gmail.com>
Link: https://lore.kernel.org/r/20190729143109.18683-1-johannes@sipsolutions.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Depending on the regulatory domain, leaving a DFS channel requires
a new CAC to be performed when returning back to that channel.
If needed, update dfs states after a driver channel switch.
Signed-off-by: Michael Vassernis <michael.vassernis@tandemg.com>
Link: https://lore.kernel.org/r/20190729060024.5660-1-michael.vassernis@tandemg.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When associated BSS completes channel switch procedure, its channel
record needs to be updated. The existing mac80211 solution was
extended to cfg80211 in commit 5dc8cdce1d ("mac80211/cfg80211:
update bss channel on channel switch").
However that solution still appears to be incomplete as it may lead
to duplicated scan entries for associated BSS after channel switch.
The root cause of the problem is as follows. Each BSS entry is
included into the following data structures:
- bss list rdev->bss_list
- bss search tree rdev->bss_tree
Updating BSS channel record without rebuilding bss_tree may break
tree search since cmp_bss considers all of the following: channel,
bssid, ssid. When BSS channel is updated, but its location in bss_tree
is not updated, then subsequent search operations may fail to locate
this BSS since they will be traversing bss_tree in wrong direction.
As a result, for scan performed after associated BSS channel switch,
cfg80211_bss_update may add the second entry for the same BSS to both
bss_list and bss_tree, rather then update the existing one.
To summarize, if BSS channel needs to be updated, then bss_tree should
be rebuilt in order to put updated BSS entry into a proper location.
This commit suggests the following straightforward solution:
- if new entry has been already created for BSS after channel switch,
then use its IEs to update known BSS entry and then remove new
entry completely
- use rb_erase/rb_insert_bss reinstall updated BSS in bss_tree
- for nontransmit BSS entry, the whole transmit BSS hierarchy
is updated
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20190726163922.27509-3-sergey.matyukevich.os@quantenna.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch implements minor refactoring for cfg80211_bss_update function.
Code path for updating known BSS is extracted into dedicated
cfg80211_update_known_bss function.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20190726163922.27509-2-sergey.matyukevich.os@quantenna.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Include wiphy address setup in wiphy dumps and new wiphy events. The
wiphy permanent address is exposed as ATTR_MAC. If addr_mask is setup,
then it is included as ATTR_MAC_MASK attribute. If multiple addresses
are available, then their are exposed in a nested ATTR_MAC_ADDRS array.
This information is already exposed via sysfs, but it makes sense to
include it in the wiphy dump as well.
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Link: https://lore.kernel.org/r/20190722113312.14031-3-denkenz@gmail.com
[use just nla_nest_start(), this is new functionality]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 33d915d9e8 ("{nl,mac}80211: allow 4addr AP operation on
crypto controlled devices") has introduced a change which allows
4addr operation on crypto controlled devices (ex: ath10k). This
change has inadvertently impacted the interface combinations logic
on such devices.
General rule is that software interfaces like AP/VLAN should not be
listed under supported interface combinations and should not be
considered during validation of these combinations; because of the
aforementioned change, AP/VLAN interfaces(if present) will be checked
against interfaces supported by the device and blocks valid interface
combinations.
Consider a case where an AP and AP/VLAN are up and running; when a
second AP device is brought up on the same physical device, this AP
will be checked against the AP/VLAN interface (which will not be
part of supported interface combinations of the device) and blocks
second AP to come up.
Add a new API cfg80211_iftype_allowed() to fix the problem, this
API works for all devices with/without SW crypto control.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Fixes: 33d915d9e8 ("{nl,mac}80211: allow 4addr AP operation on crypto controlled devices")
Link: https://lore.kernel.org/r/1563779690-9716-1-git-send-email-mpubbise@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we just read jiffies over and over again, a non-transmitting
entry may have a newer timestamp than the transmitting one,
leading to possible confusion on expiry. Give them all the same
timestamp when creating them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20190703133823.10530-3-johannes@sipsolutions.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Don't parse the multi-BSSID structures if we couldn't even create
their transmitting BSS, this would confuse all of our tracking.
This also means that non_tx_data->tx_bss will never be NULL, so
we can clean up a little bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20190703133823.10530-2-johannes@sipsolutions.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_inform_single_bss_frame_data() doesn't need the
non_tx_data data argument since it's always NULL.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Link: https://lore.kernel.org/r/20190703133823.10530-1-johannes@sipsolutions.net
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20190703070142.GA29993@kroah.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of open coding the CCM aead mode in the driver, and invoking
the AES block cipher block by block, use a ccm(aes) aead transform
which already encapsulates this functionality. This is a cleaner use
of the crypto API, and permits optimized implementations to be used,
which are typically much faster and deal more efficiently with the
SIMD register file, which usually needs to be preserved/restored in
order to use special AES instructions.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Link: https://lore.kernel.org/r/20190617091901.7063-1-ard.biesheuvel@linaro.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking updates from David Miller:
"Some highlights from this development cycle:
1) Big refactoring of ipv6 route and neigh handling to support
nexthop objects configurable as units from userspace. From David
Ahern.
2) Convert explored_states in BPF verifier into a hash table,
significantly decreased state held for programs with bpf2bpf
calls, from Alexei Starovoitov.
3) Implement bpf_send_signal() helper, from Yonghong Song.
4) Various classifier enhancements to mvpp2 driver, from Maxime
Chevallier.
5) Add aRFS support to hns3 driver, from Jian Shen.
6) Fix use after free in inet frags by allocating fqdirs dynamically
and reworking how rhashtable dismantle occurs, from Eric Dumazet.
7) Add act_ctinfo packet classifier action, from Kevin
Darbyshire-Bryant.
8) Add TFO key backup infrastructure, from Jason Baron.
9) Remove several old and unused ISDN drivers, from Arnd Bergmann.
10) Add devlink notifications for flash update status to mlxsw driver,
from Jiri Pirko.
11) Lots of kTLS offload infrastructure fixes, from Jakub Kicinski.
12) Add support for mv88e6250 DSA chips, from Rasmus Villemoes.
13) Various enhancements to ipv6 flow label handling, from Eric
Dumazet and Willem de Bruijn.
14) Support TLS offload in nfp driver, from Jakub Kicinski, Dirk van
der Merwe, and others.
15) Various improvements to axienet driver including converting it to
phylink, from Robert Hancock.
16) Add PTP support to sja1105 DSA driver, from Vladimir Oltean.
17) Add mqprio qdisc offload support to dpaa2-eth, from Ioana
Radulescu.
18) Add devlink health reporting to mlx5, from Moshe Shemesh.
19) Convert stmmac over to phylink, from Jose Abreu.
20) Add PTP PHC (Physical Hardware Clock) support to mlxsw, from
Shalom Toledo.
21) Add nftables SYNPROXY support, from Fernando Fernandez Mancera.
22) Convert tcp_fastopen over to use SipHash, from Ard Biesheuvel.
23) Track spill/fill of constants in BPF verifier, from Alexei
Starovoitov.
24) Support bounded loops in BPF, from Alexei Starovoitov.
25) Various page_pool API fixes and improvements, from Jesper Dangaard
Brouer.
26) Just like ipv4, support ref-countless ipv6 route handling. From
Wei Wang.
27) Support VLAN offloading in aquantia driver, from Igor Russkikh.
28) Add AF_XDP zero-copy support to mlx5, from Maxim Mikityanskiy.
29) Add flower GRE encap/decap support to nfp driver, from Pieter
Jansen van Vuuren.
30) Protect against stack overflow when using act_mirred, from John
Hurley.
31) Allow devmap map lookups from eBPF, from Toke Høiland-Jørgensen.
32) Use page_pool API in netsec driver, Ilias Apalodimas.
33) Add Google gve network driver, from Catherine Sullivan.
34) More indirect call avoidance, from Paolo Abeni.
35) Add kTLS TX HW offload support to mlx5, from Tariq Toukan.
36) Add XDP_REDIRECT support to bnxt_en, from Andy Gospodarek.
37) Add MPLS manipulation actions to TC, from John Hurley.
38) Add sending a packet to connection tracking from TC actions, and
then allow flower classifier matching on conntrack state. From
Paul Blakey.
39) Netfilter hw offload support, from Pablo Neira Ayuso"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2080 commits)
net/mlx5e: Return in default case statement in tx_post_resync_params
mlx5: Return -EINVAL when WARN_ON_ONCE triggers in mlx5e_tls_resync().
net: dsa: add support for BRIDGE_MROUTER attribute
pkt_sched: Include const.h
net: netsec: remove static declaration for netsec_set_tx_de()
net: netsec: remove superfluous if statement
netfilter: nf_tables: add hardware offload support
net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload
net: flow_offload: add flow_block_cb_is_busy() and use it
net: sched: remove tcf block API
drivers: net: use flow block API
net: sched: use flow block API
net: flow_offload: add flow_block_cb_{priv, incref, decref}()
net: flow_offload: add list handling functions
net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()
net: flow_offload: rename TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*
net: flow_offload: rename TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND
net: flow_offload: add flow_block_cb_setup_simple()
net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC
net: hisilicon: Add an rx_desc to adapt HI13X1_GMAC
...
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 5.3:
API:
- Test shash interface directly in testmgr
- cra_driver_name is now mandatory
Algorithms:
- Replace arc4 crypto_cipher with library helper
- Implement 5 way interleave for ECB, CBC and CTR on arm64
- Add xxhash
- Add continuous self-test on noise source to drbg
- Update jitter RNG
Drivers:
- Add support for SHA204A random number generator
- Add support for 7211 in iproc-rng200
- Fix fuzz test failures in inside-secure
- Fix fuzz test failures in talitos
- Fix fuzz test failures in qat"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (143 commits)
crypto: stm32/hash - remove interruptible condition for dma
crypto: stm32/hash - Fix hmac issue more than 256 bytes
crypto: stm32/crc32 - rename driver file
crypto: amcc - remove memset after dma_alloc_coherent
crypto: ccp - Switch to SPDX license identifiers
crypto: ccp - Validate the the error value used to index error messages
crypto: doc - Fix formatting of new crypto engine content
crypto: doc - Add parameter documentation
crypto: arm64/aes-ce - implement 5 way interleave for ECB, CBC and CTR
crypto: arm64/aes-ce - add 5 way interleave routines
crypto: talitos - drop icv_ool
crypto: talitos - fix hash on SEC1.
crypto: talitos - move struct talitos_edesc into talitos.h
lib/scatterlist: Fix mapping iterator when sg->offset is greater than PAGE_SIZE
crypto/NX: Set receive window credits to max number of CRBs in RxFIFO
crypto: asymmetric_keys - select CRYPTO_HASH where needed
crypto: serpent - mark __serpent_setkey_sbox noinline
crypto: testmgr - dynamically allocate crypto_shash
crypto: testmgr - dynamically allocate testvec_config
crypto: talitos - eliminate unneeded 'done' functions at build time
...
-----BEGIN PGP SIGNATURE-----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=E3bF
-----END PGP SIGNATURE-----
Merge tag 'keys-acl-20190703' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull keyring ACL support from David Howells:
"This changes the permissions model used by keys and keyrings to be
based on an internal ACL by the following means:
- Replace the permissions mask internally with an ACL that contains a
list of ACEs, each with a specific subject with a permissions mask.
Potted default ACLs are available for new keys and keyrings.
ACE subjects can be macroised to indicate the UID and GID specified
on the key (which remain). Future commits will be able to add
additional subject types, such as specific UIDs or domain
tags/namespaces.
Also split a number of permissions to give finer control. Examples
include splitting the revocation permit from the change-attributes
permit, thereby allowing someone to be granted permission to revoke
a key without allowing them to change the owner; also the ability
to join a keyring is split from the ability to link to it, thereby
stopping a process accessing a keyring by joining it and thus
acquiring use of possessor permits.
- Provide a keyctl to allow the granting or denial of one or more
permits to a specific subject. Direct access to the ACL is not
granted, and the ACL cannot be viewed"
* tag 'keys-acl-20190703' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
keys: Provide KEYCTL_GRANT_PERMISSION
keys: Replace uid/gid/perm permissions checking with an ACL
Replace the uid/gid/perm permissions checking on a key with an ACL to allow
the SETATTR and SEARCH permissions to be split. This will also allow a
greater range of subjects to represented.
============
WHY DO THIS?
============
The problem is that SETATTR and SEARCH cover a slew of actions, not all of
which should be grouped together.
For SETATTR, this includes actions that are about controlling access to a
key:
(1) Changing a key's ownership.
(2) Changing a key's security information.
(3) Setting a keyring's restriction.
And actions that are about managing a key's lifetime:
(4) Setting an expiry time.
(5) Revoking a key.
and (proposed) managing a key as part of a cache:
(6) Invalidating a key.
Managing a key's lifetime doesn't really have anything to do with
controlling access to that key.
Expiry time is awkward since it's more about the lifetime of the content
and so, in some ways goes better with WRITE permission. It can, however,
be set unconditionally by a process with an appropriate authorisation token
for instantiating a key, and can also be set by the key type driver when a
key is instantiated, so lumping it with the access-controlling actions is
probably okay.
As for SEARCH permission, that currently covers:
(1) Finding keys in a keyring tree during a search.
(2) Permitting keyrings to be joined.
(3) Invalidation.
But these don't really belong together either, since these actions really
need to be controlled separately.
Finally, there are number of special cases to do with granting the
administrator special rights to invalidate or clear keys that I would like
to handle with the ACL rather than key flags and special checks.
===============
WHAT IS CHANGED
===============
The SETATTR permission is split to create two new permissions:
(1) SET_SECURITY - which allows the key's owner, group and ACL to be
changed and a restriction to be placed on a keyring.
(2) REVOKE - which allows a key to be revoked.
The SEARCH permission is split to create:
(1) SEARCH - which allows a keyring to be search and a key to be found.
(2) JOIN - which allows a keyring to be joined as a session keyring.
(3) INVAL - which allows a key to be invalidated.
The WRITE permission is also split to create:
(1) WRITE - which allows a key's content to be altered and links to be
added, removed and replaced in a keyring.
(2) CLEAR - which allows a keyring to be cleared completely. This is
split out to make it possible to give just this to an administrator.
(3) REVOKE - see above.
Keys acquire ACLs which consist of a series of ACEs, and all that apply are
unioned together. An ACE specifies a subject, such as:
(*) Possessor - permitted to anyone who 'possesses' a key
(*) Owner - permitted to the key owner
(*) Group - permitted to the key group
(*) Everyone - permitted to everyone
Note that 'Other' has been replaced with 'Everyone' on the assumption that
you wouldn't grant a permit to 'Other' that you wouldn't also grant to
everyone else.
Further subjects may be made available by later patches.
The ACE also specifies a permissions mask. The set of permissions is now:
VIEW Can view the key metadata
READ Can read the key content
WRITE Can update/modify the key content
SEARCH Can find the key by searching/requesting
LINK Can make a link to the key
SET_SECURITY Can change owner, ACL, expiry
INVAL Can invalidate
REVOKE Can revoke
JOIN Can join this keyring
CLEAR Can clear this keyring
The KEYCTL_SETPERM function is then deprecated.
The KEYCTL_SET_TIMEOUT function then is permitted if SET_SECURITY is set,
or if the caller has a valid instantiation auth token.
The KEYCTL_INVALIDATE function then requires INVAL.
The KEYCTL_REVOKE function then requires REVOKE.
The KEYCTL_JOIN_SESSION_KEYRING function then requires JOIN to join an
existing keyring.
The JOIN permission is enabled by default for session keyrings and manually
created keyrings only.
======================
BACKWARD COMPATIBILITY
======================
To maintain backward compatibility, KEYCTL_SETPERM will translate the
permissions mask it is given into a new ACL for a key - unless
KEYCTL_SET_ACL has been called on that key, in which case an error will be
returned.
It will convert possessor, owner, group and other permissions into separate
ACEs, if each portion of the mask is non-zero.
SETATTR permission turns on all of INVAL, REVOKE and SET_SECURITY. WRITE
permission turns on WRITE, REVOKE and, if a keyring, CLEAR. JOIN is turned
on if a keyring is being altered.
The KEYCTL_DESCRIBE function translates the ACL back into a permissions
mask to return depending on possessor, owner, group and everyone ACEs.
It will make the following mappings:
(1) INVAL, JOIN -> SEARCH
(2) SET_SECURITY -> SETATTR
(3) REVOKE -> WRITE if SETATTR isn't already set
(4) CLEAR -> WRITE
Note that the value subsequently returned by KEYCTL_DESCRIBE may not match
the value set with KEYCTL_SETATTR.
=======
TESTING
=======
This passes the keyutils testsuite for all but a couple of tests:
(1) tests/keyctl/dh_compute/badargs: The first wrong-key-type test now
returns EOPNOTSUPP rather than ENOKEY as READ permission isn't removed
if the type doesn't have ->read(). You still can't actually read the
key.
(2) tests/keyctl/permitting/valid: The view-other-permissions test doesn't
work as Other has been replaced with Everyone in the ACL.
Signed-off-by: David Howells <dhowells@redhat.com>
Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update for
5.2. It contains all of the remaining GPLv2 and GPLv2+ updates that
were "easy" to determine by pattern matching. The ones after this are
going to be a bit more difficult and the people on the spdx list will be
discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud, always
nice to see in a diffstat.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyQYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnGQCghETUBotn1p3hTjY56VEs6dGzpHMAnRT0m+lv
kbsjBGEJpLbMRB2krnaU
=RMcT
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull still more SPDX updates from Greg KH:
"Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update
for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
that were "easy" to determine by pattern matching. The ones after this
are going to be a bit more difficult and the people on the spdx list
will be discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud,
always nice to see in a diffstat"
* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
...
The crypto API abstraction is not very useful for invoking ciphers
directly, especially in the case of arc4, which only has a generic
implementation in C. So let's invoke the library code directly.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The crypto API abstraction is not very useful for invoking ciphers
directly, especially in the case of arc4, which only has a generic
implementation in C. So let's invoke the library code directly.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation see readme and copying for
more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 9 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081207.060259192@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking fixes from David Miller:
"Lots of bug fixes here:
1) Out of bounds access in __bpf_skc_lookup, from Lorenz Bauer.
2) Fix rate reporting in cfg80211_calculate_bitrate_he(), from John
Crispin.
3) Use after free in psock backlog workqueue, from John Fastabend.
4) Fix source port matching in fdb peer flow rule of mlx5, from Raed
Salem.
5) Use atomic_inc_not_zero() in fl6_sock_lookup(), from Eric Dumazet.
6) Network header needs to be set for packet redirect in nfp, from
John Hurley.
7) Fix udp zerocopy refcnt, from Willem de Bruijn.
8) Don't assume linear buffers in vxlan and geneve error handlers,
from Stefano Brivio.
9) Fix TOS matching in mlxsw, from Jiri Pirko.
10) More SCTP cookie memory leak fixes, from Neil Horman.
11) Fix VLAN filtering in rtl8366, from Linus Walluij.
12) Various TCP SACK payload size and fragmentation memory limit fixes
from Eric Dumazet.
13) Use after free in pneigh_get_next(), also from Eric Dumazet.
14) LAPB control block leak fix from Jeremy Sowden"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (145 commits)
lapb: fixed leak of control-blocks.
tipc: purge deferredq list for each grp member in tipc_group_delete
ax25: fix inconsistent lock state in ax25_destroy_timer
neigh: fix use-after-free read in pneigh_get_next
tcp: fix compile error if !CONFIG_SYSCTL
hv_sock: Suppress bogus "may be used uninitialized" warnings
be2net: Fix number of Rx queues used for flow hashing
net: handle 802.1P vlan 0 packets properly
tcp: enforce tcp_min_snd_mss in tcp_mtu_probing()
tcp: add tcp_min_snd_mss sysctl
tcp: tcp_fragment() should apply sane memory limits
tcp: limit payload size of sacked skbs
Revert "net: phylink: set the autoneg state in phylink_phy_change"
bpf: fix nested bpf tracepoints with per-cpu data
bpf: Fix out of bounds memory access in bpf_sk_storage
vsock/virtio: set SOCK_DONE on peer shutdown
net: dsa: rtl8366: Fix up VLAN filtering
net: phylink: set the autoneg state in phylink_phy_change
net: add high_order_alloc_disable sysctl/static key
tcp: add tcp_tx_skb_cache sysctl
...
Convert the PM documents to ReST, in order to allow them to
build with Sphinx.
The conversion is actually:
- add blank lines and indentation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Srivatsa S. Bhat (VMware) <srivatsa@csail.mit.edu>
* a few memory leaks
* fixes for management frame protection security
and A2/A3 confusion (affecting TDLS as well)
* build fix for certificates
* etc.
-----BEGIN PGP SIGNATURE-----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=AHi5
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2019-06-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Various fixes, all over:
* a few memory leaks
* fixes for management frame protection security
and A2/A3 confusion (affecting TDLS as well)
* build fix for certificates
* etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
cfg80211_remain_on_channel_expired is used to notify userspace when
the remain on channel duration expired by sending an event. There is
no such equivalent to CMD_FRAME, where if offchannel and a duration
is provided, the card will go offchannel for that duration. Currently
there is no way for userspace to tell when that duration expired
apart from setting an independent timeout. This timeout is quite
erroneous as the kernel may not immediately send out the frame
because of scheduling or work queue delays. In testing, it was found
this timeout had to be quite large to accomidate any potential delays.
A better solution is to have the kernel send an event when this
duration has expired. There is already NL80211_CMD_FRAME_WAIT_CANCEL
which can be used to cancel a NL80211_CMD_FRAME offchannel. Using this
command matches perfectly to how NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL
works, where its both used to cancel and notify if the duration has
expired.
Signed-off-by: James Prestwood <james.prestwood@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of reporting the AP's TSF, host time was reported. Fix it.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In wiphy_new_nm(), if an error occurs after dev_set_name() and
device_initialize() have already been called, it's necessary to call
put_device() (via wiphy_free()) to avoid a memory leak.
Reported-by: syzbot+7fddca22578bc67c3fe4@syzkaller.appspotmail.com
Fixes: 1f87f7d3a3 ("cfg80211: add rfkill support")
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The bits of Rx MCS Map in VHT capability were enumerated
with index transform - index i -> (i + 1) bit => nss i. BUG!
while it should be - index i -> (i + 1) bit => (i + 1) nss.
The bug was exposed in commit a53b2a0b12 ("iwlwifi: mvm: implement VHT
extended NSS support in rs.c"), where iwlwifi started using the
function.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Fixes: b0aa75f0b1 ("ieee80211: add new VHT capability fields/parsing")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The seen_indices variable is u64 and in other parts of the code we
assume mbssid_index_ie[2] can be up to 45, so we should use the 64-bit
versions of BIT, namely, BIT_ULL().
Reported-by: Dan Carpented <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a function that iterates over the BSS entries associated with a
given wiphy and calls a callback for each iterated BSS. This can be
used by drivers in various ways, e.g., to evaluate some property for
all the BSSs in the medium.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow the userland daemon to en/disable TWT support for an AP.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
[simplify parsing code]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Require that each vendor command give a policy of its sub-attributes
in NL80211_ATTR_VENDOR_DATA, and then (stricly) check the contents,
including the NLA_F_NESTED flag that we couldn't check on the outer
layer because there we don't know yet.
It is possible to use VENDOR_CMD_RAW_DATA for raw data, but then no
nested data can be given (NLA_F_NESTED flag must be clear) and the
data is just passed as is to the command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Let drivers advertise support for station-mode SAE authentication
offload with a new NL80211_EXT_FEATURE_SAE_OFFLOAD flag.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add definition of WPA version 3 for SAE authentication.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add NL80211_ATTR_IFINDEX attribute to port authorized event to indicate
the operating interface of the device. Also put NL80211_ATTR_WIPHY
attribute in it to be consistent with the other MLME notifications.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Based on 1 normalized pattern(s):
this file is gplv2 as found in copying
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190114.657082701@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For old commands, it's fine to have .type = NLA_UNSPEC and it
behaves the same as NLA_MIN_LEN. However, for new commands with
strict validation this is no longer true, and for policy export
to userspace these are also ignored.
Fix up the remaining ones that don't have a type.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For old commands, it's fine to have .type = NLA_UNSPEC and it
behaves the same as NLA_MIN_LEN. However, for new commands with
strict validation this is no longer true, and for policy export
to userspace these are also ignored.
Fix up the remaining ones that don't have a type.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When dumping stations, memory allocated for station_info's
pertid member will leak if the nl80211 header cannot be added to
the sk_buff due to insufficient tail room.
I noticed this leak in the kmalloc-2048 cache.
Cc: stable@vger.kernel.org
Fixes: 8689c051a2 ("cfg80211: dynamically allocate per-tid stats for station info")
Signed-off-by: Andy Strohman <andy@uplevelsystems.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the BSS is expired during connection, the connect result will
trigger a kernel warning. Ideally cfg80211 should hold the BSS
before the connection is attempted, but as the BSSID is not known
in case of auth/assoc MLME offload (connect op) it doesn't.
For those drivers without the connect op cfg80211 holds down the
reference so it wil not be removed from list.
Fix this by removing the warning and silently adding the BSS back to
the bss list which is return by the driver (with proper BSSID set) or
in case the BSS is already added use that.
The requirements for drivers are documented in the API's.
Signed-off-by: Chaitanya Tata <chaitanya.tata@bluwireless.co.uk>
[formatting fixes, keep old timestamp]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As per the current design, in the case of sw crypto controlled devices,
it is the device which advertises the support for AP/VLAN iftype based
on it's ability to tranmsit packets encrypted in software
(In VLAN functionality, group traffic generated for a specific
VLAN group is always encrypted in software). Commit db3bdcb9c3
("mac80211: allow AP_VLAN operation on crypto controlled devices")
has introduced this change.
Since 4addr AP operation also uses AP/VLAN iftype, this conditional
way of advertising AP/VLAN support has broken 4addr AP mode operation on
crypto controlled devices which do not support VLAN functionality.
In the case of ath10k driver, not all firmwares have support for VLAN
functionality but all can support 4addr AP operation. Because AP/VLAN
support is not advertised for these devices, 4addr AP operations are
also blocked.
Fix this by allowing 4addr operation on devices which do not support
AP/VLAN iftype but can support 4addr AP operation (decision is based on
the wiphy flag WIPHY_FLAG_4ADDR_AP).
Cc: stable@vger.kernel.org
Fixes: db3bdcb9c3 ("mac80211: allow AP_VLAN operation on crypto controlled devices")
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The reported rate is not scaled down correctly. After applying this patch,
the function will behave just like the v/ht equivalents.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have EXPORT_.*_SYMBOL_GPL inside which was used in the
initial scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 715a123347 ("wireless: don't write C files on failures") drops
the `test -f $$f` check. The list of targets contains the
CONFIG_CFG80211_EXTRA_REGDB_KEYDIR directory itself, and this check used
to filter it out. After the check was removed, the extra keydir option
no longer works, failing with the following message:
od: 'standard input': read error: Is a directory
This commit restores the check to make extra keydir work again.
Fixes: 715a123347 ("wireless: don't write C files on failures")
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking updates from David Miller:
"Highlights:
1) Support AES128-CCM ciphers in kTLS, from Vakul Garg.
2) Add fib_sync_mem to control the amount of dirty memory we allow to
queue up between synchronize RCU calls, from David Ahern.
3) Make flow classifier more lockless, from Vlad Buslov.
4) Add PHY downshift support to aquantia driver, from Heiner
Kallweit.
5) Add SKB cache for TCP rx and tx, from Eric Dumazet. This reduces
contention on SLAB spinlocks in heavy RPC workloads.
6) Partial GSO offload support in XFRM, from Boris Pismenny.
7) Add fast link down support to ethtool, from Heiner Kallweit.
8) Use siphash for IP ID generator, from Eric Dumazet.
9) Pull nexthops even further out from ipv4/ipv6 routes and FIB
entries, from David Ahern.
10) Move skb->xmit_more into a per-cpu variable, from Florian
Westphal.
11) Improve eBPF verifier speed and increase maximum program size,
from Alexei Starovoitov.
12) Eliminate per-bucket spinlocks in rhashtable, and instead use bit
spinlocks. From Neil Brown.
13) Allow tunneling with GUE encap in ipvs, from Jacky Hu.
14) Improve link partner cap detection in generic PHY code, from
Heiner Kallweit.
15) Add layer 2 encap support to bpf_skb_adjust_room(), from Alan
Maguire.
16) Remove SKB list implementation assumptions in SCTP, your's truly.
17) Various cleanups, optimizations, and simplifications in r8169
driver. From Heiner Kallweit.
18) Add memory accounting on TX and RX path of SCTP, from Xin Long.
19) Switch PHY drivers over to use dynamic featue detection, from
Heiner Kallweit.
20) Support flow steering without masking in dpaa2-eth, from Ioana
Ciocoi.
21) Implement ndo_get_devlink_port in netdevsim driver, from Jiri
Pirko.
22) Increase the strict parsing of current and future netlink
attributes, also export such policies to userspace. From Johannes
Berg.
23) Allow DSA tag drivers to be modular, from Andrew Lunn.
24) Remove legacy DSA probing support, also from Andrew Lunn.
25) Allow ll_temac driver to be used on non-x86 platforms, from Esben
Haabendal.
26) Add a generic tracepoint for TX queue timeouts to ease debugging,
from Cong Wang.
27) More indirect call optimizations, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1763 commits)
cxgb4: Fix error path in cxgb4_init_module
net: phy: improve pause mode reporting in phy_print_status
dt-bindings: net: Fix a typo in the phy-mode list for ethernet bindings
net: macb: Change interrupt and napi enable order in open
net: ll_temac: Improve error message on error IRQ
net/sched: remove block pointer from common offload structure
net: ethernet: support of_get_mac_address new ERR_PTR error
net: usb: smsc: fix warning reported by kbuild test robot
staging: octeon-ethernet: Fix of_get_mac_address ERR_PTR check
net: dsa: support of_get_mac_address new ERR_PTR error
net: dsa: sja1105: Fix status initialization in sja1105_get_ethtool_stats
vrf: sit mtu should not be updated when vrf netdev is the link
net: dsa: Fix error cleanup path in dsa_init_module
l2tp: Fix possible NULL pointer dereference
taprio: add null check on sched_nest to avoid potential null pointer dereference
net: mvpp2: cls: fix less than zero check on a u32 variable
net_sched: sch_fq: handle non connected flows
net_sched: sch_fq: do not assume EDT packets are ordered
net: hns3: use devm_kcalloc when allocating desc_cb
net: hns3: some cleanup for struct hns3_enet_ring
...
Pull crypto update from Herbert Xu:
"API:
- Add support for AEAD in simd
- Add fuzz testing to testmgr
- Add panic_on_fail module parameter to testmgr
- Use per-CPU struct instead multiple variables in scompress
- Change verify API for akcipher
Algorithms:
- Convert x86 AEAD algorithms over to simd
- Forbid 2-key 3DES in FIPS mode
- Add EC-RDSA (GOST 34.10) algorithm
Drivers:
- Set output IV with ctr-aes in crypto4xx
- Set output IV in rockchip
- Fix potential length overflow with hashing in sun4i-ss
- Fix computation error with ctr in vmx
- Add SM4 protected keys support in ccree
- Remove long-broken mxc-scc driver
- Add rfc4106(gcm(aes)) cipher support in cavium/nitrox"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (179 commits)
crypto: ccree - use a proper le32 type for le32 val
crypto: ccree - remove set but not used variable 'du_size'
crypto: ccree - Make cc_sec_disable static
crypto: ccree - fix spelling mistake "protedcted" -> "protected"
crypto: caam/qi2 - generate hash keys in-place
crypto: caam/qi2 - fix DMA mapping of stack memory
crypto: caam/qi2 - fix zero-length buffer DMA mapping
crypto: stm32/cryp - update to return iv_out
crypto: stm32/cryp - remove request mutex protection
crypto: stm32/cryp - add weak key check for DES
crypto: atmel - remove set but not used variable 'alg_name'
crypto: picoxcell - Use dev_get_drvdata()
crypto: crypto4xx - get rid of redundant using_sd variable
crypto: crypto4xx - use sync skcipher for fallback
crypto: crypto4xx - fix cfb and ofb "overran dst buffer" issues
crypto: crypto4xx - fix ctr-aes missing output IV
crypto: ecrdsa - select ASN1 and OID_REGISTRY for EC-RDSA
crypto: ux500 - use ccflags-y instead of CFLAGS_<basename>.o
crypto: ccree - handle tee fips error during power management resume
crypto: ccree - add function to handle cryptocell tee fips error
...
Add options to strictly validate messages and dump messages,
sometimes perhaps validating dump messages non-strictly may
be required, so add an option for that as well.
Since none of this can really be applied to existing commands,
set the options everwhere using the following spatch:
@@
identifier ops;
expression X;
@@
struct genl_ops ops[] = {
...,
{
.cmd = X,
+ .validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
...
},
...
};
For new commands one should just not copy the .validate 'opt-out'
flags and thus get strict validation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently have two levels of strict validation:
1) liberal (default)
- undefined (type >= max) & NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
- garbage at end of message accepted
2) strict (opt-in)
- NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
Split out parsing strictness into four different options:
* TRAILING - check that there's no trailing data after parsing
attributes (in message or nested)
* MAXTYPE - reject attrs > max known type
* UNSPEC - reject attributes with NLA_UNSPEC policy entries
* STRICT_ATTRS - strictly validate attribute size
The default for future things should be *everything*.
The current *_strict() is a combination of TRAILING and MAXTYPE,
and is renamed to _deprecated_strict().
The current regular parsing has none of this, and is renamed to
*_parse_deprecated().
Additionally it allows us to selectively set one of the new flags
even on old policies. Notably, the UNSPEC flag could be useful in
this case, since it can be arranged (by filling in the policy) to
not be an incompatible userspace ABI change, but would then going
forward prevent forgetting attribute entries. Similar can apply
to the POLICY flag.
We end up with the following renames:
* nla_parse -> nla_parse_deprecated
* nla_parse_strict -> nla_parse_deprecated_strict
* nlmsg_parse -> nlmsg_parse_deprecated
* nlmsg_parse_strict -> nlmsg_parse_deprecated_strict
* nla_parse_nested -> nla_parse_nested_deprecated
* nla_validate_nested -> nla_validate_nested_deprecated
Using spatch, of course:
@@
expression TB, MAX, HEAD, LEN, POL, EXT;
@@
-nla_parse(TB, MAX, HEAD, LEN, POL, EXT)
+nla_parse_deprecated(TB, MAX, HEAD, LEN, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression TB, MAX, NLA, POL, EXT;
@@
-nla_parse_nested(TB, MAX, NLA, POL, EXT)
+nla_parse_nested_deprecated(TB, MAX, NLA, POL, EXT)
@@
expression START, MAX, POL, EXT;
@@
-nla_validate_nested(START, MAX, POL, EXT)
+nla_validate_nested_deprecated(START, MAX, POL, EXT)
@@
expression NLH, HDRLEN, MAX, POL, EXT;
@@
-nlmsg_validate(NLH, HDRLEN, MAX, POL, EXT)
+nlmsg_validate_deprecated(NLH, HDRLEN, MAX, POL, EXT)
For this patch, don't actually add the strict, non-renamed versions
yet so that it breaks compile if I get it wrong.
Also, while at it, make nla_validate and nla_parse go down to a
common __nla_validate_parse() function to avoid code duplication.
Ultimately, this allows us to have very strict validation for every
new caller of nla_parse()/nlmsg_parse() etc as re-introduced in the
next patch, while existing things will continue to work as is.
In effect then, this adds fully strict validation for any new command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if the NLA_F_NESTED flag was introduced more than 11 years ago, most
netlink based interfaces (including recently added ones) are still not
setting it in kernel generated messages. Without the flag, message parsers
not aware of attribute semantics (e.g. wireshark dissector or libmnl's
mnl_nlmsg_fprintf()) cannot recognize nested attributes and won't display
the structure of their contents.
Unfortunately we cannot just add the flag everywhere as there may be
userspace applications which check nlattr::nla_type directly rather than
through a helper masking out the flags. Therefore the patch renames
nla_nest_start() to nla_nest_start_noflag() and introduces nla_nest_start()
as a wrapper adding NLA_F_NESTED. The calls which add NLA_F_NESTED manually
are rewritten to use nla_nest_start().
Except for changes in include/net/netlink.h, the patch was generated using
this semantic patch:
@@ expression E1, E2; @@
-nla_nest_start(E1, E2)
+nla_nest_start_noflag(E1, E2)
@@ expression E1, E2; @@
-nla_nest_start_noflag(E1, E2 | NLA_F_NESTED)
+nla_nest_start(E1, E2)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* extended key ID support (from 802.11-2016)
* per-STA TX power control support
* mac80211 TX performance improvements
* HE (802.11ax) updates
* mesh link probing support
* enhancements of multi-BSSID support (also related to HE)
* OWE userspace processing support
-----BEGIN PGP SIGNATURE-----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=JQOx
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2019-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Various updates, notably:
* extended key ID support (from 802.11-2016)
* per-STA TX power control support
* mac80211 TX performance improvements
* HE (802.11ax) updates
* mesh link probing support
* enhancements of multi-BSSID support (also related to HE)
* OWE userspace processing support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support to allow mesh HWMP to measure link metrics on unexercised
direct mesh path by sending some data frames to other mesh points which
are not currently selected as a primary traffic path but only 1 hop away.
The absence of the primary path to the chosen node makes it necessary to
apply some form of marking on a chosen packet stream so that the packets
can be properly steered to the selected node for testing, and not by the
regular mesh path lookup.
Tested-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We are copying one entire structure to another of the same type in
nl80211_notify_radar_detection, so it's simpler and safer to do a
struct assignment instead of memcpy().
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The cfg80211_merge_profile() and ieee802_11_find_bssid_profile() are
a bit cleaner if we just pass the merged_ie pointer instead of a pointer
to the pointer.
This isn't a functional change, it's just a clean up.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds support to set transmit power setting type and transmit
power level attributes to NL80211_CMD_SET_STATION in order to facilitate
adjusting the transmit power level of a station associated to the AP.
The added attributes allow selection of automatic and limited transmit
power level, with the level defined in dBm format.
Co-developed-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Ashok Raj Nagarajan <arnagara@codeaurora.org>
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL)
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL)
Notice that, in this case, variable size_of_regd is not necessary,
hence it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL)
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL)
Notice that, in this case, variable size_of_regd is not necessary,
hence it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The zero check on variable changed is redundant as it must be
between 1 and 3 at the end of the proceeding if statement block.
Remove the redundant check.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
FullMAC STAs have no way to update bss channel after CSA channel switch
completion. As a result, user-space tools may provide inconsistent
channel info. For instance, consider the following two commands:
$ sudo iw dev wlan0 link
$ sudo iw dev wlan0 info
The latter command gets channel info from the hardware, so most probably
its output will be correct. However the former command gets channel info
from scan cache, so its output will contain outdated channel info.
In fact, current bss channel info will not be updated until the
next [re-]connect.
Note that mac80211 STAs have a workaround for this, but it requires
access to internal cfg80211 data, see ieee80211_chswitch_work:
/* XXX: shouldn't really modify cfg80211-owned data! */
ifmgd->associated->channel = sdata->csa_chandef.chan;
This patch suggests to convert mac80211 workaround into cfg80211 behavior
and to update current bss channel in cfg80211_ch_switch_notify.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for IEEE 802.11-2016 "Extended Key ID for Individually
Addressed Frames".
Extend cfg80211 and nl80211 to allow pairwise keys to be installed for
Rx only, enable Tx separately and allow Key ID 1 for pairwise keys.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[use NLA_POLICY_RANGE() for NL80211_KEY_MODE]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since an element is limited to 255 octets, a profile may be split
split to several elements. Support the split as defined in the 11ax
draft 3. Detect legacy split and print a net-rate limited warning,
since there is no ROI in supporting this probably non-existent
split.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Subelement profile may specify element IDs it doesn't inherit
from the management frame. Support it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When creating the IEs for the nontransmitted BSS, the index
element is skipped. However, we need to get DTIM values from
it, so don't skip it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The flags field in 'struct shash_desc' never actually does anything.
The only ostensibly supported flag is CRYPTO_TFM_REQ_MAY_SLEEP.
However, no shash algorithm ever sleeps, making this flag a no-op.
With this being the case, inevitably some users who can't sleep wrongly
pass MAY_SLEEP. These would all need to be fixed if any shash algorithm
actually started sleeping. For example, the shash_ahash_*() functions,
which wrap a shash algorithm with the ahash API, pass through MAY_SLEEP
from the ahash API to the shash API. However, the shash functions are
called under kmap_atomic(), so actually they're assumed to never sleep.
Even if it turns out that some users do need preemption points while
hashing large buffers, we could easily provide a helper function
crypto_shash_update_large() which divides the data into smaller chunks
and calls crypto_shash_update() and cond_resched() for each chunk. It's
not necessary to have a flag in 'struct shash_desc', nor is it necessary
to make individual shash algorithms aware of this at all.
Therefore, remove shash_desc::flags, and document that the
crypto_shash_*() functions can be called from any context.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit c82c06ce43d3("cfg80211: Notify all User Hints To self managed wiphys")
notified all new user hints to self managed wiphy's after device registration.
But it didn't do this for anything other than cell base hints done before
registration.
This needs to be done during wiphy registration of a self managed device also,
so that the previous user settings are retained.
Fixes: c82c06ce43 ("cfg80211: Notify all User Hints To self managed wiphys")
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This interface allows the host driver to offload OWE processing
to user space. This intends to support OWE (Opportunistic Wireless
Encryption) AKM by the drivers that implement SME but rely on the
user space for the cryptographic/OWE processing in AP mode. Such
drivers are not capable of processing/deriving the DH IE.
A new NL80211 command - NL80211_CMD_UPDATE_OWE_INFO is introduced
to send the request/event between the host driver and user space.
Driver shall provide the OWE info (MAC address and DH IE) of
the peer to user space for cryptographic processing of the DH IE
through the event. Accordingly, the user space shall update the
OWE info/DH IE to the driver.
Following is the sequence in AP mode for OWE authentication.
Driver passes the OWE info obtained from the peer in the
Association Request to the user space through the event
cfg80211_update_owe_info_event. User space shall process the
OWE info received and generate new OWE info. This OWE info is
passed to the driver through NL80211_CMD_UPDATE_OWE_INFO
request. Driver eventually uses this OWE info to send the
Association Response to the peer.
This OWE info in the command interface carries the IEs that include
PMKID of the peer if the PMKSA is still valid or an updated DH IE
for generating a new PMKSA with the peer.
Signed-off-by: Liangwei Dong <liangwei@codeaurora.org>
Signed-off-by: Sunil Dutt <usdutt@codeaurora.org>
Signed-off-by: Srinivas Dasari <dasaris@codeaurora.org>
[remove policy initialization - no longer exists]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for mesh airtime link metric attribute
NL80211_STA_INFO_AIRTIME_LINK_METRIC.
Signed-off-by: Narayanraddi Masti <team.nmasti@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This commit adds the support to specify the RSSI thresholds per
band for each match set. This enhances the current behavior which
specifies a single rssi_threshold across all the bands by
introducing the rssi_threshold_per_band. These per band rssi
thresholds are referred through NL80211_BAND_* (enum nl80211_band)
variables as attribute types. Such attributes/values per each
band are nested through NL80211_ATTR_SCHED_SCAN_MIN_RSSI.
These band specific rssi thresholds shall take precedence over
the current rssi_thold per match set.
Drivers indicate this support through
%NL80211_EXT_FEATURE_SCHED_SCAN_BAND_SPECIFIC_RSSI_THOLD.
These per band rssi attributes/values does not specify
"default RSSI filter" as done by
NL80211_SCHED_SCAN_MATCH_ATTR_RSSI to stay backward compatible.
That said, these per band rssi values have to be specified for
the corresponding matchset.
Signed-off-by: vamsi krishna <vamsin@codeaurora.org>
Signed-off-by: Srinivas Dasari <dasaris@codeaurora.org>
[rebase on refactoring, add policy]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The sched scan code here is really deep - avoid one level
of indentation by short-circuiting the loop instead of
putting everything into the if block.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This commit adds NL80211_FLAG_CLEAR_SKB flag to other NL commands
that carry key data to ensure they do not stick around on heap
after the SKB is freed.
Also introduced this flag for NL80211_CMD_VENDOR as there are sub
commands which configure the keys.
Signed-off-by: Sunil Dutt <usdutt@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use kmemdup rather than duplicating its implementation
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When building with -Wsometimes-uninitialized, Clang warns:
net/wireless/util.c:1223:11: warning: variable 'result' is used
uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
Clang can't evaluate at this point that WARN(1, ...) always returns true
because __ret_warn_on is defined as !!(condition), which isn't
immediately evaluated as 1. Change this branch to else so that it's
clear to Clang that we intend to bail out here.
Link: https://github.com/ClangBuiltLinux/linux/issues/382
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The support added for regulatory WMM rules did not handle
the case of regulatory domain intersections. Fix it.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Fixes: 230ebaa189 ("cfg80211: read wmm rules from regulatory database")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since maxattr is common, the policy can't really differ sanely,
so make it common as well.
The only user that did in fact manage to make a non-common policy
is taskstats, which has to be really careful about it (since it's
still using a common maxattr!). This is no longer supported, but
we can fake it using pre_doit.
This reduces the size of e.g. nl80211.o (which has lots of commands):
text data bss dec hex filename
398745 14323 2240 415308 6564c net/wireless/nl80211.o (before)
397913 14331 2240 414484 65314 net/wireless/nl80211.o (after)
--------------------------------
-832 +8 0 -824
Which is obviously just 8 bytes for each command, and an added 8
bytes for the new policy pointer. I'm not sure why the ops list is
counted as .text though.
Most of the code transformations were done using the following spatch:
@ops@
identifier OPS;
expression POLICY;
@@
struct genl_ops OPS[] = {
...,
{
- .policy = POLICY,
},
...
};
@@
identifier ops.OPS;
expression ops.POLICY;
identifier fam;
expression M;
@@
struct genl_family fam = {
.ops = OPS,
.maxattr = M,
+ .policy = POLICY,
...
};
This also gets rid of devlink_nl_cmd_region_read_dumpit() accessing
the cb->data as ops, which we want to change in a later genl patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge net-next to resolve a conflict and to get the mac80211
rhashtable fixes so further patches can be applied on top.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sometimes, we may want to transport higher bandwidth data
through vendor events, and in that case sending it multicast
is a bad idea. Allow vendor events to be unicast.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This extends the NL80211_CMD_ASSOCIATE event case to report
NL80211_ATTR_REQ_IE similarly to what is already done with the
NL80211_CMD_CONNECT events if the driver provides this information. In
practice, this adds (Re)Association Request frame information element
reporting to mac80211 drivers for the cases where user space SME is
used.
This provides more information for user space to figure out which
capabilities were negotiated for the association. For example, this can
be used to determine whether HT, VHT, or HE is used.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch is to use eth_broadcast_addr() to assign broadcast address
insetad of memset().
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
Enforce the first argument to be a correct type of a pointer to struct
element and avoid unnecessary typecasts from const to non-const pointers
(the change in validate_ie_attr() is needed to make this part work). In
addition, avoid signed/unsigned comparison within for_each_element() and
mark struct element packed just in case.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Thomas Pedersen