This change makes it so that we store the virtual address of the page
in the netdev_alloc_cache instead of the page pointer. The idea behind
this is to avoid multiple calls to page_address since the virtual address
is required for every access, but the page pointer is only needed at
allocation or reset of the page.
While I was at it I also reordered the netdev_alloc_cache structure a bit
so that the size is always 16 bytes by dropping size in the case where
PAGE_SIZE is greater than or equal to 32KB.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing I found that the testing for pfmemalloc in build_skb was
rather expensive. I found the issue to be two-fold. First we have to get
from the virtual address to the head page and that comes at the cost of
something like 11 cycles. Then there is the cost for reading pfmemalloc out
of the head page which can be cache cold due to the fact that
put_page_testzero is likely invalidating the cache-line on one or more
CPUs as the fragments can be shared.
To avoid this extra expense I have added a pfmemalloc member to the
netdev_alloc_cache. I then pushed pieces of __alloc_rx_skb into
__napi_alloc_skb and __netdev_alloc_skb so that I could rewrite them to
make use of the cached pfmemalloc value. The result is that my perf traces
show a reduction from 9.28% overhead to 3.7% for the code covered by
build_skb, __alloc_rx_skb, and __napi_alloc_skb when performing a test with
the packet being dropped instead of being handed to napi_gro_receive.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
> net/core/skbuff.c:4108:13: sparse: incorrect type in assignment (different base types)
> net/ipv6/mcast_snoop.c:63 ipv6_mc_check_exthdrs() warn: unsigned 'offset' is never less than zero.
Introduced by 9afd85c9e4
("net: Export IGMP/MLD message validation code")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch, the IGMP and MLD message validation functions are moved
from the bridge code to IPv4/IPv6 multicast files. Some small
refactoring was done to enhance readibility and to iron out some
differences in behaviour between the IGMP and MLD parsing code (e.g. the
skb-cloning of MLD messages is now only done if necessary, just like the
IGMP part always did).
Finally, these IGMP and MLD message validation functions are exported so
that not only the bridge can use it but batman-adv later, too.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
build_skb() should look at the page pfmemalloc status.
If set, this means page allocator allocated this page in the
expectation it would help to free other pages. Networking
stack can do that only if skb->pfmemalloc is also set.
Also, we must refrain using high order pages from the pfmemalloc
reserve, so __page_frag_refill() must also use __GFP_NOMEMALLOC for
them. Under memory pressure, using order-0 pages is probably the best
strategy.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Wed, Apr 15, 2015 at 05:41:26PM +0200, Nicolas Dichtel wrote:
> Le 15/04/2015 15:57, Herbert Xu a écrit :
> >On Wed, Apr 15, 2015 at 06:22:29PM +0800, Herbert Xu wrote:
> [snip]
> >Subject: skbuff: Do not scrub skb mark within the same name space
> >
> >The commit ea23192e8e ("tunnels:
> Maybe add a Fixes tag?
> Fixes: ea23192e8e ("tunnels: harmonize cleanup done on skb on rx path")
>
> >harmonize cleanup done on skb on rx path") broke anyone trying to
> >use netfilter marking across IPv4 tunnels. While most of the
> >fields that are cleared by skb_scrub_packet don't matter, the
> >netfilter mark must be preserved.
> >
> >This patch rearranges skb_scurb_packet to preserve the mark field.
> nit: s/scurb/scrub
>
> Else it's fine for me.
Sure.
PS I used the wrong email for James the first time around. So
let me repeat the question here. Should secmark be preserved
or cleared across tunnels within the same name space? In fact,
do our security models even support name spaces?
---8<---
The commit ea23192e8e ("tunnels:
harmonize cleanup done on skb on rx path") broke anyone trying to
use netfilter marking across IPv4 tunnels. While most of the
fields that are cleared by skb_scrub_packet don't matter, the
netfilter mark must be preserved.
This patch rearranges skb_scrub_packet to preserve the mark field.
Fixes: ea23192e8e ("tunnels: harmonize cleanup done on skb on rx path")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reverts commit b8fb4e0648
because the secmark must be preserved even when a packet crosses
namespace boundaries. The reason is that security labels apply to
the system as a whole and is not per-namespace.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
Test that sk != NULL before reading sk->sk_tsflags.
Fixes: 49ca0d8bfa ("net-timestamp: no-payload option")
Reported-by: One Thousand Gnomes <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John reported that my previous commit added a regression
on his router.
This is because sender_cpu & napi_id share a common location,
so get_xps_queue() can see garbage and perform an out of bound access.
We need to make sure sender_cpu is cleared before doing the transmit,
otherwise any NIC busy poll enabled (skb_mark_napi_id()) can trigger
this bug.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: John <jw@nuclearfallout.net>
Bisected-by: John <jw@nuclearfallout.net>
Fixes: 2bd82484bb ("xps: fix xps for stacked devices")
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers use copybreak to copy tiny frames into smaller skb,
and this smaller skb might not have skb->head_frag set for various
reasons.
skb_gro_receive() currently doesn't allow to aggregate the smaller skb
into the previous GRO packet if this GRO packet has at least 2 MSS in
it.
Following workload easily demonstrates the problem.
netperf -t TCP_RR -H target -- -r 3000,3000
(tcpdump shows one GRO packet with 2 MSS, plus one additional packet of
104 bytes that should have been appended.)
It turns out that we can remove code from skb_gro_receive(), because
commit 8a29111c7c ("net: gro: allow to build full sized skb") and its
followups removed the assumption that a GRO packet with a frag_list had
to have an empty head.
Removing this code allows the aggregation of the last (incomplete) frame
in some RPC workloads. Note that tcp_gro_receive() already takes care of
forcing a flush if necessary, including this case.
If we want to avoid using frag_list in the first place (in forwarding
workloads for example, as the outgoing NIC is generally not able to cope
with skbs having a frag_list), we need to address this separately.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Although it is clear that textsearch state is intentionally passed to
skb_find_text() as uninitialized argument, it was never used by the
callers. Therefore, we can simplify skb_find_text() by making it
local variable.
Signed-off-by: Bojan Prtvar <prtvar.b@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Non NAPI drivers can call skb_tstamp_tx() and then sock_queue_err_skb()
from hard IRQ context.
Therefore, sock_dequeue_err_skb() needs to block hard irq or
corruptions or hangs can happen.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 364a9e9324 ("sock: deduplicate errqueue dequeue")
Fixes: cb820f8e4b ("net: Provide a generic socket error queue delivery method for Tx time stamps.")
Signed-off-by: David S. Miller <davem@davemloft.net>
A typical qdisc setup is the following :
bond0 : bonding device, using HTB hierarchy
eth1/eth2 : slaves, multiqueue NIC, using MQ + FQ qdisc
XPS allows to spread packets on specific tx queues, based on the cpu
doing the send.
Problem is that dequeues from bond0 qdisc can happen on random cpus,
due to the fact that qdisc_run() can dequeue a batch of packets.
CPUA -> queue packet P1 on bond0 qdisc, P1->ooo_okay=1
CPUA -> queue packet P2 on bond0 qdisc, P2->ooo_okay=0
CPUB -> dequeue packet P1 from bond0
enqueue packet on eth1/eth2
CPUC -> dequeue packet P2 from bond0
enqueue packet on eth1/eth2 using sk cache (ooo_okay is 0)
get_xps_queue() then might select wrong queue for P1, since current cpu
might be different than CPUA.
P2 might be sent on the old queue (stored in sk->sk_tx_queue_mapping),
if CPUC runs a bit faster (or CPUB spins a bit on qdisc lock)
Effect of this bug is TCP reorders, and more generally not optimal
TX queue placement. (A victim bulk flow can be migrated to the wrong TX
queue for a while)
To fix this, we have to record sender cpu number the first time
dev_queue_xmit() is called for one tx skb.
We can union napi_id (used on receive path) and sender_cpu,
granted we clear sender_cpu in skb_scrub_packet() (credit to Willem for
this union idea)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tx timestamps are looped onto the error queue on top of an skb. This
mechanism leaks packet headers to processes unless the no-payload
options SOF_TIMESTAMPING_OPT_TSONLY is set.
Add a sysctl that optionally drops looped timestamp with data. This
only affects processes without CAP_NET_RAW.
The policy is checked when timestamps are generated in the stack.
It is possible for timestamps with data to be reported after the
sysctl is set, if these were queued internally earlier.
No vulnerability is immediately known that exploits knowledge
gleaned from packet headers, but it may still be preferable to allow
administrators to lock down this path at the cost of possible
breakage of legacy applications.
Signed-off-by: Willem de Bruijn <willemb@google.com>
----
Changes
(v1 -> v2)
- test socket CAP_NET_RAW instead of capable(CAP_NET_RAW)
(rfc -> v1)
- document the sysctl in Documentation/sysctl/net.txt
- fix access control race: read .._OPT_TSONLY only once,
use same value for permission check and skb generation.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add timestamping option SOF_TIMESTAMPING_OPT_TSONLY. For transmit
timestamps, this loops timestamps on top of empty packets.
Doing so reduces the pressure on SO_RCVBUF. Payload inspection and
cmsg reception (aside from timestamps) are no longer possible. This
works together with a follow on patch that allows administrators to
only allow tx timestamping if it does not loop payload or metadata.
Signed-off-by: Willem de Bruijn <willemb@google.com>
----
Changes (rfc -> v1)
- add documentation
- remove unnecessary skb->len test (thanks to Richard Cochran)
Signed-off-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not needed, only four cases:
- kfree_skb (or one of its aliases).
Don't need to zero, memory will be freed.
- kfree_skb_partial and head was stolen: memory will be freed.
- skb_morph: The skb header fields (including tc ones) will be
copied over from the 'to-be-morphed' skb right after
skb_release_head_state returns.
- skb_segment: Same as before, all the skb header
fields are copied over from the original skb right away.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_scrub_packet() is called when a packet switches between a context
such as between underlay and overlay, between namespaces, or between
L3 subnets.
While we already scrub the packet mark, connection tracking entry,
and cached destination, the security mark/context is left intact.
It seems wrong to inherit the security context of a packet when going
from overlay to underlay or across forwarding paths.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Flavio Leitner <fbl@sysclose.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change pulls the core functionality out of __netdev_alloc_skb and
places them in a new function named __alloc_rx_skb. The reason for doing
this is to make these bits accessible to a new function __napi_alloc_skb.
In addition __alloc_rx_skb now has a new flags value that is used to
determine which page frag pool to allocate from. If the SKB_ALLOC_NAPI
flag is set then the NAPI pool is used. The advantage of this is that we
do not have to use local_irq_save/restore when accessing the NAPI pool from
NAPI context.
In my test setup I saw at least 11ns of savings using the napi_alloc_skb
function versus the netdev_alloc_skb function, most of this being due to
the fact that we didn't have to call local_irq_save/restore.
The main use case for napi_alloc_skb would be for things such as copybreak
or page fragment based receive paths where an skb is allocated after the
data has been received instead of before.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch splits the netdev_alloc_frag function up so that it can be used
on one of two page frag pools instead of being fixed on the
netdev_alloc_cache. By doing this we can add a NAPI specific function
__napi_alloc_frag that accesses a pool that is only used from softirq
context. The advantage to this is that we do not need to call
local_irq_save/restore which can be a significant savings.
I also took the opportunity to refactor the core bits that were placed in
__alloc_page_frag. First I updated the allocation to do either a 32K
allocation or an order 0 page. This is based on the changes in commmit
d9b2938aa where it was found that latencies could be reduced in case of
failures. Then I also rewrote the logic to work from the end of the page to
the start. By doing this the size value doesn't have to be used unless we
have run out of space for page fragments. Finally I cleaned up the atomic
bits so that we just do an atomic_sub_and_test and if that returns true then
we set the page->_count via an atomic_set. This way we can remove the extra
conditional for the atomic_read since it would have led to an atomic_inc in
the case of success anyway.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ce1a4ea3f1 ("net: avoid one atomic operation in skb_clone()")
took the wrong way to save one atomic operation.
It is actually possible to avoid two atomic operations, if we
do not change skb->fclone values, and only rely on clone_ref
content to signal if the clone is available or not.
skb_clone() can simply use the fast clone if clone_ref is 1.
kfree_skbmem() can avoid the atomic_dec_and_test() if clone_ref is 1.
Note that because we usually free the clone before the original skb,
this particular attempt is only done for the original skb to have better
branch prediction.
SKB_FCLONE_FREE is removed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Chris Mason <clm@fb.com>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Cc: Vijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ieee802154/fakehard.c
A bug fix went into 'net' for ieee802154/fakehard.c, which is removed
in 'net-next'.
Add build fix into the merge from Stephen Rothwell in openvswitch, the
logging macros take a new initial 'log' argument, a new call was added
in 'net' so when we merge that in here we have to explicitly add the
new 'log' arg to it else the build fails.
Signed-off-by: David S. Miller <davem@davemloft.net>
Not sure what I was thinking, but doing anything after
releasing a refcount is suicidal or/and embarrassing.
By the time we set skb->fclone to SKB_FCLONE_FREE, another cpu
could have released last reference and freed whole skb.
We potentially corrupt memory or trap if CONFIG_DEBUG_PAGEALLOC is set.
Reported-by: Chris Mason <clm@fb.com>
Fixes: ce1a4ea3f1 ("net: avoid one atomic operation in skb_clone()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
So it can be used from out of openvswitch code.
Did couple of cosmetic changes on the way, namely variable naming and
adding support for 8021AD proto.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
note that skb_make_writable already exists in net/netfilter/core.c
but does something slightly different.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new GSO type, SKB_GSO_TUNNEL_REMCSUM, which indicates remote
checksum offload being done (in this case inner checksum must not
be offloaded to the NIC).
Added logic in __skb_udp_tunnel_segment to handle remote checksum
offload case.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch generalizes commit d6a4a10411 ("tcp: GSO should be TSQ
friendly") to protocols using skb_set_owner_w()
TCP uses its own destructor (tcp_wfree) and needs a more complex scheme
as explained in commit 6ff50cd555 ("tcp: gso: do not generate out of
order packets")
This allows UDP sockets using UFO to get proper backpressure,
thus avoiding qdisc drops and excessive cpu usage.
Here are performance test results (macvlan on vlan):
- Before
# netperf -t UDP_STREAM ...
Socket Message Elapsed Messages
Size Size Time Okay Errors Throughput
bytes bytes secs # # 10^6bits/sec
212992 65507 60.00 144096 1224195 1258.56
212992 60.00 51 0.45
Average: CPU %user %nice %system %iowait %steal %idle
Average: all 0.23 0.00 25.26 0.08 0.00 74.43
- After
# netperf -t UDP_STREAM ...
Socket Message Elapsed Messages
Size Size Time Okay Errors Throughput
bytes bytes secs # # 10^6bits/sec
212992 65507 60.00 109593 0 957.20
212992 60.00 109593 957.20
Average: CPU %user %nice %system %iowait %steal %idle
Average: all 0.18 0.00 8.38 0.02 0.00 91.43
[edumazet] Rewrote patch and changelog.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
if ->encapsulation is set we have to use inner_tcp_hdrlen and add the
size of the inner network headers too.
This is 'mostly harmless'; tbf might send skb that is slightly over
quota or drop skb even if it would have fit.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull percpu consistent-ops changes from Tejun Heo:
"Way back, before the current percpu allocator was implemented, static
and dynamic percpu memory areas were allocated and handled separately
and had their own accessors. The distinction has been gone for many
years now; however, the now duplicate two sets of accessors remained
with the pointer based ones - this_cpu_*() - evolving various other
operations over time. During the process, we also accumulated other
inconsistent operations.
This pull request contains Christoph's patches to clean up the
duplicate accessor situation. __get_cpu_var() uses are replaced with
with this_cpu_ptr() and __this_cpu_ptr() with raw_cpu_ptr().
Unfortunately, the former sometimes is tricky thanks to C being a bit
messy with the distinction between lvalues and pointers, which led to
a rather ugly solution for cpumask_var_t involving the introduction of
this_cpu_cpumask_var_ptr().
This converts most of the uses but not all. Christoph will follow up
with the remaining conversions in this merge window and hopefully
remove the obsolete accessors"
* 'for-3.18-consistent-ops' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (38 commits)
irqchip: Properly fetch the per cpu offset
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t -fix
ia64: sn_nodepda cannot be assigned to after this_cpu conversion. Use __this_cpu_write.
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t
Revert "powerpc: Replace __get_cpu_var uses"
percpu: Remove __this_cpu_ptr
clocksource: Replace __this_cpu_ptr with raw_cpu_ptr
sparc: Replace __get_cpu_var uses
avr32: Replace __get_cpu_var with __this_cpu_write
blackfin: Replace __get_cpu_var uses
tile: Use this_cpu_ptr() for hardware counters
tile: Replace __get_cpu_var uses
powerpc: Replace __get_cpu_var uses
alpha: Replace __get_cpu_var
ia64: Replace __get_cpu_var uses
s390: cio driver &__get_cpu_var replacements
s390: Replace __get_cpu_var uses
mips: Replace __get_cpu_var uses
MIPS: Replace __get_cpu_var uses in FPU emulator.
arm: Replace __this_cpu_ptr with raw_cpu_ptr
...
This is illegal to use atomic_set(&page->_count, ...) even if we 'own'
the page. Other entities in the kernel need to use get_page_unless_zero()
to get a reference to the page before testing page properties, so we could
loose a refcount increment.
The only case it is valid is when page->_count is 0
Fixes: 540eb7bf0b ("net: Update alloc frag to reduce get/put page usage and recycle pages")
Signed-off-by: Eric Dumaze <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix following warning.
Warning(.//net/core/skbuff.c:4142): No description found for parameter 'header_len'
Warning(.//net/core/skbuff.c:4142): No description found for parameter 'data_len'
Warning(.//net/core/skbuff.c:4142): No description found for parameter 'max_page_order'
Warning(.//net/core/skbuff.c:4142): No description found for parameter 'errcode'
Warning(.//net/core/skbuff.c:4142): No description found for parameter 'gfp_mask'
Acutually the descriptions exist, but missing "@" in front.
This problem start to happen when following commit was merged
into Linus's tree during 3.18-rc1 merge period.
commit 2e4e441071
net: add alloc_skb_with_frags() helper
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Its unfortunate we have to walk again skb list to find the tail
after segmentation, even if data is probably hot in cpu caches.
skb_segment() can store the tail of the list into segs->prev,
and validate_xmit_skb_list() can immediately get the tail.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains another batch with Netfilter/IPVS updates
for net-next, they are:
1) Add abstracted ICMP codes to the nf_tables reject expression. We
introduce four reasons to reject using ICMP that overlap in IPv4
and IPv6 from the semantic point of view. This should simplify the
maintainance of dual stack rule-sets through the inet table.
2) Move nf_send_reset() functions from header files to per-family
nf_reject modules, suggested by Patrick McHardy.
3) We have to use IS_ENABLED(CONFIG_BRIDGE_NETFILTER) everywhere in the
code now that br_netfilter can be modularized. Convert remaining spots
in the network stack code.
4) Use rcu_barrier() in the nf_tables module removal path to ensure that
we don't leave object that are still pending to be released via
call_rcu (that may likely result in a crash).
5) Remove incomplete arch 32/64 compat from nft_compat. The original (bad)
idea was to probe the word size based on the xtables match/target info
size, but this assumption is wrong when you have to dump the information
back to userspace.
6) Allow to filter from prerouting and postrouting in the nf_tables bridge.
In order to emulate the ebtables NAT chains (which are actually simple
filter chains with no special semantics), we have support filtering from
this hooks too.
7) Add explicit module dependency between xt_physdev and br_netfilter.
This provides a way to detect if the user needs br_netfilter from
the configuration path. This should reduce the breakage of the
br_netfilter modularization.
8) Cleanup coding style in ip_vs.h, from Simon Horman.
9) Fix crash in the recently added nf_tables masq expression. We have
to register/unregister the notifiers to clean up the conntrack table
entries from the module init/exit path, not from the rule addition /
deletion path. From Arturo Borrero.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
SKB_FCLONE_UNAVAILABLE has overloaded meaning depending on type of skb.
1: If skb is allocated from head_cache, it indicates fclone is not available.
2: If skb is a companion fclone skb (allocated from fclone_cache), it indicates
it is available to be used.
To avoid confusion for case 2 above, this patch replaces
SKB_FCLONE_UNAVAILABLE with SKB_FCLONE_FREE where appropriate. For fclone
companion skbs, this indicates it is free for use.
SKB_FCLONE_UNAVAILABLE will now simply indicate skb is from head_cache and
cannot / will not have a companion fclone.
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_gro_receive() is only called from tcp_gro_receive() which is
not in a module.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/r8152.c
net/netfilter/nfnetlink.c
Both r8152 and nfnetlink conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
In 34666d4 ("netfilter: bridge: move br_netfilter out of the core"),
the bridge netfilter code has been modularized.
Use IS_ENABLED instead of ifdef to cover the module case.
Fixes: 34666d4 ("netfilter: bridge: move br_netfilter out of the core")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fast clone cloning can actually avoid an atomic_inc(), if we
guarantee prior clone_ref value is 1.
This requires a change kfree_skbmem(), to perform the
atomic_dec_and_test() on clone_ref before setting fclone to
SKB_FCLONE_UNAVAILABLE.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lets use a proper structure to clearly document and implement
skb fast clones.
Then, we might experiment more easily alternative layouts.
This patch adds a new skb_fclone_busy() helper, used by tcp and xfrm,
to stop leaking of implementation details.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 8a29111c7c ("net: gro: allow to build full sized skb")
I added a regression for linear skb that traditionally force GRO
to use the frag_list fallback.
Erez Shitrit found that at most two segments were aggregated and
the "if (skb_gro_len(p) != pinfo->gso_size)" test was failing.
This is because pinfo at this spot still points to the last skb in the
chain, instead of the first one, where we find the correct gso_size
information.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 8a29111c7c ("net: gro: allow to build full sized skb")
Reported-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With proliferation of bit fields in sk_buff, __copy_skb_header() became
quite expensive, showing as the most expensive function in a GSO
workload.
__copy_skb_header() performance is also critical for non GSO TCP
operations, as it is used from skb_clone()
This patch carefully moves all the fields that were not copied in a
separate zone : cloned, nohdr, fclone, peeked, head_frag, xmit_more
Then I moved all other fields and all other copied fields in a section
delimited by headers_start[0]/headers_end[0] section so that we
can use a single memcpy() call, inlined by compiler using long
word load/stores.
I also tried to make all copies in the natural orders of sk_buff,
to help hardware prefetching.
I made sure sk_buff size did not change.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cache skb_shinfo(skb) in a variable to avoid computing it multiple
times.
Reorganize the tests to remove one indentation level.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While profiling TCP stack, I noticed one useless atomic operation
in tcp_sendmsg(), caused by skb_header_release().
It turns out all current skb_header_release() users have a fresh skb,
that no other user can see, so we can avoid one atomic operation.
Introduce __skb_header_release() to clearly document this.
This gave me a 1.5 % improvement on TCP_RR workload.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract from sock_alloc_send_pskb() code building skb with frags,
so that we can reuse this in other contexts.
Intent is to use it from tcp_send_rcvq(), tcp_collapse(), ...
We also want to replace some skb_linearize() calls to a more reliable
strategy in pathological cases where we need to reduce number of frags.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can allow a segment with FIN to be aggregated,
if we take care to add tcp flags,
and if skb_try_coalesce() takes care of zero sized skbs.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a possible issue with the use, or lack thereof of sk_refcnt and
sk_wmem_alloc in the wifi ack status functionality.
Specifically if a socket were to request acknowledgements, and the socket
were to have sk_refcnt drop to 0 resulting in it waiting on sk_wmem_alloc
to reach 0 it would be possible to have sock_queue_err_skb orphan the last
buffer, resulting in __sk_free being called on the socket. After this the
buffer is enqueued on sk_error_queue, however the queue has already been
flushed resulting in at least a memory leak, if not a data corruption.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds some documentation to the call skb_clone_sk. This is
meant to help clarify the purpose of the function for other developers.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy timestamping takes a different path than the regular timestamping
does in that it will create a clone first so that the packets needing to be
timestamped can be placed in a queue, or the context block could be used.
In order to support these use cases I am pulling the core of the code out
so it can be used in other drivers beyond just phy devices.
In addition I have added a destructor named sock_efree which is meant to
provide a simple way for dropping the reference to skb exceptions that
aren't part of either the receive or send windows for the socket, and I
have removed some duplication in spots where this destructor could be used
in place of sock_edemux.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change merges the shared bits that exist between skb_tx_tstamp and
skb_complete_tx_timestamp. By doing this we can avoid the two diverging as
there were already changes pushed into skb_tx_tstamp that hadn't made it
into the other function.
In addition this resolves issues with the fact that
skb_complete_tx_timestamp was included in linux/skbuff.h even though it was
only compiled in if phy timestamping was enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix spelling typo found in DocBook/networking.xml.
It is because the neworking.xml is generated from comments
in the source, I have to fix typo in comments within the source.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk->sk_error_queue is dequeued in four locations. All share the
exact same logic. Deduplicate.
Also collapse the two critical sections for dequeue (at the top of
the recv handler) and signal (at the bottom).
This moves signal generation for the next packet forward, which should
be harmless.
It also changes the behavior if the recv handler exits early with an
error. Previously, a signal for follow-up packets on the errqueue
would then not be scheduled. The new behavior, to always signal, is
arguably a bug fix.
For rxrpc, the change causes the same function to be called repeatedly
for each queued packet (because the recv handler == sk_error_report).
It is likely that all packets will fail for the same reason (e.g.,
memory exhaustion).
This code runs without sk_lock held, so it is not safe to trust that
sk->sk_err is immutable inbetween releasing q->lock and the subsequent
test. Introduce int err just to avoid this potential race.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace uses of get_cpu_var for address calculation through this_cpu_ptr.
Cc: netdev@vger.kernel.org
Cc: Eric Dumazet <edumazet@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently the functionality to untag traffic on input resides
as part of the vlan module and is build only when VLAN support
is enabled in the kernel. When VLAN is disabled, the function
vlan_untag() turns into a stub and doesn't really untag the
packets. This seems to create an interesting interaction
between VMs supporting checksum offloading and some network drivers.
There are some drivers that do not allow the user to change
tx-vlan-offload feature of the driver. These drivers also seem
to assume that any VLAN-tagged traffic they transmit will
have the vlan information in the vlan_tci and not in the vlan
header already in the skb. When transmitting skbs that already
have tagged data with partial checksum set, the checksum doesn't
appear to be updated correctly by the card thus resulting in a
failure to establish TCP connections.
The following is a packet trace taken on the receiver where a
sender is a VM with a VLAN configued. The host VM is running on
doest not have VLAN support and the outging interface on the
host is tg3:
10:12:43.503055 52:54:00:ae:42:3f > 28:d2:44:7d:c2:de, ethertype 802.1Q
(0x8100), length 78: vlan 100, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 27243,
offset 0, flags [DF], proto TCP (6), length 60)
10.0.100.1.58545 > 10.0.100.10.ircu-2: Flags [S], cksum 0xdc39 (incorrect
-> 0x48d9), seq 1069378582, win 29200, options [mss 1460,sackOK,TS val
4294837885 ecr 0,nop,wscale 7], length 0
10:12:44.505556 52:54:00:ae:42:3f > 28:d2:44:7d:c2:de, ethertype 802.1Q
(0x8100), length 78: vlan 100, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 27244,
offset 0, flags [DF], proto TCP (6), length 60)
10.0.100.1.58545 > 10.0.100.10.ircu-2: Flags [S], cksum 0xdc39 (incorrect
-> 0x44ee), seq 1069378582, win 29200, options [mss 1460,sackOK,TS val
4294838888 ecr 0,nop,wscale 7], length 0
This connection finally times out.
I've only access to the TG3 hardware in this configuration thus have
only tested this with TG3 driver. There are a lot of other drivers
that do not permit user changes to vlan acceleration features, and
I don't know if they all suffere from a similar issue.
The patch attempt to fix this another way. It moves the vlan header
stipping code out of the vlan module and always builds it into the
kernel network core. This way, even if vlan is not supported on
a virtualizatoin host, the virtual machines running on top of such
host will still work with VLANs enabled.
CC: Patrick McHardy <kaber@trash.net>
CC: Nithin Nayak Sujir <nsujir@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/Makefile
net/ipv6/sysctl_net_ipv6.c
Two ipv6_table_template[] additions overlap, so the index
of the ipv6_table[x] assignments needed to be adjusted.
In the drivers/net/Makefile case, we've gotten rid of the
garbage whereby we had to list every single USB networking
driver in the top-level Makefile, there is just one
"USB_NETWORKING" that guards everything.
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP timestamping extends SO_TIMESTAMPING to bytestreams.
Bytestreams do not have a 1:1 relationship between send() buffers and
network packets. The feature interprets a send call on a bytestream as
a request for a timestamp for the last byte in that send() buffer.
The choice corresponds to a request for a timestamp when all bytes in
the buffer have been sent. That assumption depends on in-order kernel
transmission. This is the common case. That said, it is possible to
construct a traffic shaping tree that would result in reordering.
The guarantee is strong, then, but not ironclad.
This implementation supports send and sendpages (splice). GSO replaces
one large packet with multiple smaller packets. This patch also copies
the option into the correct smaller packet.
This patch does not yet support timestamping on data in an initial TCP
Fast Open SYN, because that takes a very different data path.
If ID generation in ee_data is enabled, bytestream timestamps return a
byte offset, instead of the packet counter for datagrams.
The implementation supports a single timestamp per packet. It silenty
replaces requests for previous timestamps. To avoid missing tstamps,
flush the tcp queue by disabling Nagle, cork and autocork. Missing
tstamps can be detected by offset when the ee_data ID is enabled.
Implementation details:
- On GSO, the timestamping code can be included in the main loop. I
moved it into its own loop to reduce the impact on the common case
to a single branch.
- To avoid leaking the absolute seqno to userspace, the offset
returned in ee_data must always be relative. It is an offset between
an skb and sk field. The first is always set (also for GSO & ACK).
The second must also never be uninitialized. Only allow the ID
option on sockets in the ESTABLISHED state, for which the seqno
is available. Never reset it to zero (instead, move it to the
current seqno when reenabling the option).
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kernel transmit latency is often incurred in the packet scheduler.
Introduce a new timestamp on transmission just before entering the
scheduler. When data travels through multiple devices (bonding,
tunneling, ...) each device will export an individual timestamp.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Datagrams timestamped on transmission can coexist in the kernel stack
and be reordered in packet scheduling. When reading looped datagrams
from the socket error queue it is not always possible to unique
correlate looped data with original send() call (for application
level retransmits). Even if possible, it may be expensive and complex,
requiring packet inspection.
Introduce a data-independent ID mechanism to associate timestamps with
send calls. Pass an ID alongside the timestamp in field ee_data of
sock_extended_err.
The ID is a simple 32 bit unsigned int that is associated with the
socket and incremented on each send() call for which software tx
timestamp generation is enabled.
The feature is enabled only if SOF_TIMESTAMPING_OPT_ID is set, to
avoid changing ee_data for existing applications that expect it 0.
The counter is reset each time the flag is reenabled. Reenabling
does not change the ID of already submitted data. It is possible
to receive out of order IDs if the timestamp stream is not quiesced
first.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Applications that request kernel tx timestamps with SO_TIMESTAMPING
read timestamps as recvmsg() ancillary data. The response is defined
implicitly as timespec[3].
1) define struct scm_timestamping explicitly and
2) add support for new tstamp types. On tx, scm_timestamping always
accompanies a sock_extended_err. Define previously unused field
ee_info to signal the type of ts[0]. Introduce SCM_TSTAMP_SND to
define the existing behavior.
The reception path is not modified. On rx, no struct similar to
sock_extended_err is passed along with SCM_TIMESTAMPING.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When performing segmentation, the mac_len value is copied right
out of the original skb. However, this value is not always set correctly
(like when the packet is VLAN-tagged) and we'll end up copying a bad
value.
One way to demonstrate this is to configure a VM which tags
packets internally and turn off VLAN acceleration on the forwarding
bridge port. The packets show up corrupt like this:
16:18:24.985548 52:54:00🆎be:25 > 52:54:00:26:ce:a3, ethertype 802.1Q
(0x8100), length 1518: vlan 100, p 0, ethertype 0x05e0,
0x0000: 8cdb 1c7c 8cdb 0064 4006 b59d 0a00 6402 ...|...d@.....d.
0x0010: 0a00 6401 9e0d b441 0a5e 64ec 0330 14fa ..d....A.^d..0..
0x0020: 29e3 01c9 f871 0000 0101 080a 000a e833)....q.........3
0x0030: 000f 8c75 6e65 7470 6572 6600 6e65 7470 ...unetperf.netp
0x0040: 6572 6600 6e65 7470 6572 6600 6e65 7470 erf.netperf.netp
0x0050: 6572 6600 6e65 7470 6572 6600 6e65 7470 erf.netperf.netp
0x0060: 6572 6600 6e65 7470 6572 6600 6e65 7470 erf.netperf.netp
...
This also leads to awful throughput as GSO packets are dropped and
cause retransmissions.
The solution is to set the mac_len using the values already available
in then new skb. We've already adjusted all of the header offset, so we
might as well correctly figure out the mac_len using skb_reset_mac_len().
After this change, packets are segmented correctly and performance
is restored.
CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave Jones reported that a crash is occurring in
csum_partial
tcp_gso_segment
inet_gso_segment
? update_dl_migration
skb_mac_gso_segment
__skb_gso_segment
dev_hard_start_xmit
sch_direct_xmit
__dev_queue_xmit
? dev_hard_start_xmit
dev_queue_xmit
ip_finish_output
? ip_output
ip_output
ip_forward_finish
ip_forward
ip_rcv_finish
ip_rcv
__netif_receive_skb_core
? __netif_receive_skb_core
? trace_hardirqs_on
__netif_receive_skb
netif_receive_skb_internal
napi_gro_complete
? napi_gro_complete
dev_gro_receive
? dev_gro_receive
napi_gro_receive
It looks like a likely culprit is that SKB_GSO_CB()->csum_start is
not set correctly when doing non-scatter gather. We are using
offset as opposed to doffset.
Reported-by: Dave Jones <davej@redhat.com>
Tested-by: Dave Jones <davej@redhat.com>
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 7e2b10c1e5 ("net: Support for multiple checksums with gso")
Acked-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geert reported issues regarding checksum complete and UDP.
The logic introduced in commit 7e3cead517
("net: Save software checksum complete") is not correct.
This patch:
1) Restores code in __skb_checksum_complete_header except for setting
CHECKSUM_UNNECESSARY. This function may be calculating checksum on
something less than skb->len.
2) Adds saving checksum to __skb_checksum_complete. The full packet
checksum 0..skb->len is calculated without adding in pseudo header.
This value is saved in skb->csum and then the pseudo header is added
to that to derive the checksum for validation.
3) In both __skb_checksum_complete_header and __skb_checksum_complete,
set skb->csum_valid to whether checksum of zero was computed. This
allows skb_csum_unnecessary to return true without changing to
CHECKSUM_UNNECESSARY which was done previously.
4) Copy new csum related bits in __copy_skb_header.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/core/rtnetlink.c
net/core/skbuff.c
Both conflicts were very simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several instances where a pskb_copy or __pskb_copy is
immediately followed by an skb_clone.
Add a couple of new functions to allow the copy skb to be allocated
from the fclone cache and thus speed up subsequent skb_clone calls.
Cc: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Marek Lindner <mareklindner@neomailbox.ch>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Antonio Quartulli <antonio@meshcoding.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Arvid Brodin <arvid.brodin@alten.se>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Cc: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
Cc: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Allan Stephens <allan.stephens@windriver.com>
Cc: Andrew Hendry <andrew.hendry@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Reviewed-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a kernel BUG_ON in skb_segment. It is hit when
testing two VMs on openvswitch with one VM acting as VXLAN gateway.
During VXLAN packet GSO, skb_segment is called with skb->data
pointing to inner TCP payload. skb_segment calls skb_network_protocol
to retrieve the inner protocol. skb_network_protocol actually expects
skb->data to point to MAC and it calls pskb_may_pull with ETH_HLEN.
This ends up pulling in ETH_HLEN data from header tail. As a result,
pskb_trim logic is skipped and BUG_ON is hit later.
Move skb_push in front of skb_network_protocol so that skb->data
lines up properly.
kernel BUG at net/core/skbuff.c:2999!
Call Trace:
[<ffffffff816ac412>] tcp_gso_segment+0x122/0x410
[<ffffffff816bc74c>] inet_gso_segment+0x13c/0x390
[<ffffffff8164b39b>] skb_mac_gso_segment+0x9b/0x170
[<ffffffff816b3658>] skb_udp_tunnel_segment+0xd8/0x390
[<ffffffff816b3c00>] udp4_ufo_fragment+0x120/0x140
[<ffffffff816bc74c>] inet_gso_segment+0x13c/0x390
[<ffffffff8109d742>] ? default_wake_function+0x12/0x20
[<ffffffff8164b39b>] skb_mac_gso_segment+0x9b/0x170
[<ffffffff8164b4d0>] __skb_gso_segment+0x60/0xc0
[<ffffffff8164b6b3>] dev_hard_start_xmit+0x183/0x550
[<ffffffff8166c91e>] sch_direct_xmit+0xfe/0x1d0
[<ffffffff8164bc94>] __dev_queue_xmit+0x214/0x4f0
[<ffffffff8164bf90>] dev_queue_xmit+0x10/0x20
[<ffffffff81687edb>] ip_finish_output+0x66b/0x890
[<ffffffff81688a58>] ip_output+0x58/0x90
[<ffffffff816c628f>] ? fib_table_lookup+0x29f/0x350
[<ffffffff816881c9>] ip_local_out_sk+0x39/0x50
[<ffffffff816cbfad>] iptunnel_xmit+0x10d/0x130
[<ffffffffa0212200>] vxlan_xmit_skb+0x1d0/0x330 [vxlan]
[<ffffffffa02a3919>] vxlan_tnl_send+0x129/0x1a0 [openvswitch]
[<ffffffffa02a2cd6>] ovs_vport_send+0x26/0xa0 [openvswitch]
[<ffffffffa029931e>] do_output+0x2e/0x50 [openvswitch]
Signed-off-by: Wei-Chun Chao <weichunc@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating a GSO packet segment we may need to set more than
one checksum in the packet (for instance a TCP checksum and
UDP checksum for VXLAN encapsulation). To be efficient, we want
to do checksum calculation for any part of the packet at most once.
This patch adds csum_start offset to skb_gso_cb. This tracks the
starting offset for skb->csum which is initially set in skb_segment.
When a protocol needs to compute a transport checksum it calls
gso_make_checksum which computes the checksum value from the start
of transport header to csum_start and then adds in skb->csum to get
the full checksum. skb->csum and csum_start are then updated to reflect
the checksum of the resultant packet starting from the transport header.
This patch also adds a flag to skbuff, encap_hdr_csum, which is set
in *gso_segment fucntions to indicate that a tunnel protocol needs
checksum calculation
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_alb.c
drivers/net/ethernet/altera/altera_msgdma.c
drivers/net/ethernet/altera/altera_sgdma.c
net/ipv6/xfrm6_output.c
Several cases of overlapping changes.
The xfrm6_output.c has a bug fix which overlaps the renaming
of skb->local_df to skb->ignore_df.
In the Altera TSE driver cases, the register access cleanups
in net-next overlapped with bug fixes done in net.
Similarly a bug fix to send ALB packets in the bonding driver using
the right source address overlaps with cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting from linux-3.13, GRO attempts to build full size skbs.
Problem is the commit assumed one particular field in skb->cb[]
was clean, but it is not the case on some stacked devices.
Timo reported a crash in case traffic is decrypted before
reaching a GRE device.
Fix this by initializing NAPI_GRO_CB(skb)->last at the right place,
this also removes one conditional.
Thanks a lot to Timo for providing full reports and bisecting this.
Fixes: 8a29111c7c ("net: gro: allow to build full sized skb")
Bisected-by: Timo Teras <timo.teras@iki.fi>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by several people, rename local_df to ignore_df,
since it means "ignore df bit if it is set".
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several spots in the kernel perform a sequence like:
skb_queue_tail(&sk->s_receive_queue, skb);
sk->sk_data_ready(sk, skb->len);
But at the moment we place the SKB onto the socket receive queue it
can be consumed and freed up. So this skb->len access is potentially
to freed up memory.
Furthermore, the skb->len can be modified by the consumer so it is
possible that the value isn't accurate.
And finally, no actual implementation of this callback actually uses
the length argument. And since nobody actually cared about it's
value, lots of call sites pass arbitrary values in such as '0' and
even '1'.
So just remove the length argument from the callback, that way there
is no confusion whatsoever and all of these use-after-free cases get
fixed as a side effect.
Based upon a patch by Eric Dumazet and his suggestion to audit this
issue tree-wide.
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of tcp, gso_size contains the tcpmss.
For UFO (udp fragmentation offloading) skbs, gso_size is the fragment
payload size, i.e. we must not account for udp header size.
Otherwise, when using virtio drivers, a to-be-forwarded UFO GSO packet
will be needlessly fragmented in the forward path, because we think its
individual segments are too large for the outgoing link.
Fixes: fe6cc55f3a ("net: ip, ipv6: handle gso skbs in forwarding path")
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Tobias Brunner <tobias@strongswan.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/marvell/mvneta.c
The mvneta.c conflict is a case of overlapping changes,
a conversion to devm_ioremap_resource() vs. a conversion
to netdev_alloc_pcpu_stats.
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_network_protocol() already accounts for multiple vlan
headers that may be present in the skb. However, skb_mac_gso_segment()
doesn't know anything about it and assumes that skb->mac_len
is set correctly to skip all mac headers. That may not
always be the case. If we are simply forwarding the packet (via
bridge or macvtap), all vlan headers may not be accounted for.
A simple solution is to allow skb_network_protocol to return
the vlan depth it has calculated. This way skb_mac_gso_segment
will correctly skip all mac headers.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_zerocopy can copy elements of the frags array between skbs, but it doesn't
orphan them. Also, it doesn't handle errors, so this patch takes care of that
as well, and modify the callers accordingly. skb_tx_error() is also added to
the callers so they will signal the failed delivery towards the creator of the
skb.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/r8152.c
drivers/net/xen-netback/netback.c
Both the r8152 and netback conflicts were simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
consolidate duplicate code is skb_checksum_setup() helpers
Realizing that the skb_maybe_pull_tail() calls in the IP-protocol
specific portions of both helpers are terminal ones (i.e. no further
pulls are expected), their maximum size to be pulled can be made match
their minimal size needed, thus making the code identical and hence
possible to be moved into another helper.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Paul Durrant <paul.durrant@citrix.com>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_segment copies frags around, so we need
to copy them carefully to avoid accessing
user memory after reporting completion to userspace
through a callback.
skb_segment doesn't normally happen on datapath:
TSO needs to be disabled - so disabling zero copy
in this case does not look like a big deal.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
fskb is unrelated to frag: it's coming from
frag_list. Rename it list_skb to avoid confusion.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rename local variable to make it easier to tell at a glance that we are
dealing with a head skb.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_frag can in fact point at either skb
or fskb so rename it generally "frag".
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
net/ipv6/sit.c
The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.
The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
When using nftables with CONFIG_NETFILTER_XT_TARGET_TRACE=n, we get
lots of "TRACE: filter:output:policy:1 IN=..." warnings as several
places will leave skb->nf_trace uninitialised.
Unlike iptables tracing functionality is not conditional in nftables,
so always copy/zero nf_trace setting when nftables is enabled.
Move this into __nf_copy() helper.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
As compared with skb_to_sgvec, skb_to_sgvec_nomark only map skb to given sglist
without mark the sg which contain last skb data as the end. So the caller can
mannipulate sg list as will when padding new data after the first call without
calling sg_unmark_end to expend sg list.
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This patch fixed following Warning while executing "make htmldocs".
Warning(/net/core/skbuff.c:2164): No description found for parameter 'from'
Warning(/net/core/skbuff.c:2164): Excess function parameter 'source'
description in 'skb_zerocopy'
Replace "@source" with "@from" fixed the warning.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves part of Eric Dumazets skb_gso_seglen helper from tbf sched to
skbuff core so it may be reused by upcoming ip forwarding path patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) BPF debugger and asm tool by Daniel Borkmann.
2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.
3) Correct reciprocal_divide and update users, from Hannes Frederic
Sowa and Daniel Borkmann.
4) Currently we only have a "set" operation for the hw timestamp socket
ioctl, add a "get" operation to match. From Ben Hutchings.
5) Add better trace events for debugging driver datapath problems, also
from Ben Hutchings.
6) Implement auto corking in TCP, from Eric Dumazet. Basically, if we
have a small send and a previous packet is already in the qdisc or
device queue, defer until TX completion or we get more data.
7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.
8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
Borkmann.
9) Share IP header compression code between Bluetooth and IEEE802154
layers, from Jukka Rissanen.
10) Fix ipv6 router reachability probing, from Jiri Benc.
11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.
12) Support tunneling in GRO layer, from Jerry Chu.
13) Allow bonding to be configured fully using netlink, from Scott
Feldman.
14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
already get the TCI. From Atzm Watanabe.
15) New "Heavy Hitter" qdisc, from Terry Lam.
16) Significantly improve the IPSEC support in pktgen, from Fan Du.
17) Allow ipv4 tunnels to cache routes, just like sockets. From Tom
Herbert.
18) Add Proportional Integral Enhanced packet scheduler, from Vijay
Subramanian.
19) Allow openvswitch to mmap'd netlink, from Thomas Graf.
20) Key TCP metrics blobs also by source address, not just destination
address. From Christoph Paasch.
21) Support 10G in generic phylib. From Andy Fleming.
22) Try to short-circuit GRO flow compares using device provided RX
hash, if provided. From Tom Herbert.
The wireless and netfilter folks have been busy little bees too.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
net/cxgb4: Fix referencing freed adapter
ipv6: reallocate addrconf router for ipv6 address when lo device up
fib_frontend: fix possible NULL pointer dereference
rtnetlink: remove IFLA_BOND_SLAVE definition
rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
qlcnic: update version to 5.3.55
qlcnic: Enhance logic to calculate msix vectors.
qlcnic: Refactor interrupt coalescing code for all adapters.
qlcnic: Update poll controller code path
qlcnic: Interrupt code cleanup
qlcnic: Enhance Tx timeout debugging.
qlcnic: Use bool for rx_mac_learn.
bonding: fix u64 division
rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
sfc: Use the correct maximum TX DMA ring size for SFC9100
Add Shradha Shah as the sfc driver maintainer.
net/vxlan: Share RX skb de-marking and checksum checks with ovs
tulip: cleanup by using ARRAY_SIZE()
ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
net/cxgb4: Don't retrieve stats during recovery
...
Having this struct in module memory could Oops when if the module is
unloaded while the buffer still persists in a pipe.
Since sock_pipe_buf_ops is essentially the same as fuse_dev_pipe_buf_steal
merge them into nosteal_pipe_buf_ops (this is the same as
default_pipe_buf_ops except stealing the page from the buffer is not
allowed).
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Cc: stable@vger.kernel.org
This patch adds a function to set up the partial checksum offset for IP
packets (and optionally re-calculate the pseudo-header checksum) into the
core network code.
The implementation was previously private and duplicated between xen-netback
and xen-netfront, however it is not xen-specific and is potentially useful
to any network driver.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Gross says:
====================
[GIT net-next] Open vSwitch
Open vSwitch changes for net-next/3.14. Highlights are:
* Performance improvements in the mechanism to get packets to userspace
using memory mapped netlink and skb zero copy where appropriate.
* Per-cpu flow stats in situations where flows are likely to be shared
across CPUs. Standard flow stats are used in other situations to save
memory and allocation time.
* A handful of code cleanups and rationalization.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the skb zerocopy logic written for nfnetlink queue available for
use by other modules.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Reviewed-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jesse Gross <jesse@nicira.com>
We can use kfree_skb_list() instead of open coding it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds skb_copy_hash to copy rxhash and l4_rxhash from one skb to another.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must clear local_df when passing the skb between namespaces as the
packet is not local to the new namespace any more and thus may not get
fragmented by local rules. Fred Templin noticed that other namespaces
do fragment IPv6 packets while forwarding. Instead they should have send
back a PTB.
The same problem should be present when forwarding DF-IPv4 packets
between namespaces.
Reported-by: Templin, Fred L <Fred.L.Templin@boeing.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently GRO started generating packets with frag_lists of frags.
This was not handled by GSO, thus leading to a crash.
Thankfully these packets are of a regular form and are easy to
handle. This patch handles them in two ways. For completely
non-linear frag_list entries, we simply continue to iterate over
the frag_list frags once we exhaust the normal frags. For frag_list
entries with linear parts, we call pskb_trim on the first part
of the frag_list skb, and then process the rest of the frags in
the usual way.
This patch also kills a chunk of dead frag_list code that has
obviously never ever been run since it ends up generating a bogus
GSO-segmented packet with a frag_list entry.
Future work is planned to split super big packets into TSO
ones.
Fixes: 8a29111c7c ("net: gro: allow to build full sized skb")
Reported-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Reported-by: Jerry Chu <hkchu@google.com>
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Tested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pushing original fragments through causes several problems. For example
for matching, frags may not be matched correctly. Take following
example:
<example>
On HOSTA do:
ip6tables -I INPUT -p icmpv6 -j DROP
ip6tables -I INPUT -p icmpv6 -m icmp6 --icmpv6-type 128 -j ACCEPT
and on HOSTB you do:
ping6 HOSTA -s2000 (MTU is 1500)
Incoming echo requests will be filtered out on HOSTA. This issue does
not occur with smaller packets than MTU (where fragmentation does not happen)
</example>
As was discussed previously, the only correct solution seems to be to use
reassembled skb instead of separete frags. Doing this has positive side
effects in reducing sk_buff by one pointer (nfct_reasm) and also the reams
dances in ipvs and conntrack can be removed.
Future plan is to remove net/ipv6/netfilter/nf_conntrack_reasm.c
entirely and use code in net/ipv6/reassembly.c instead.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use "@" to refer to parameters in the kernel-doc description. According
to Documentation/kernel-doc-nano-HOWTO.txt "&" shall be used to refer to
structures only.
Signed-off-by: Mathias Krause <mathias.krause@secunet.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function has usage beside IPsec so move it to the core skbuff code.
While doing so, give it some documentation and change its return type to
'unsigned char *' to be in line with skb_put().
Signed-off-by: Mathias Krause <mathias.krause@secunet.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes we need to coalesce the rx frags to avoid frag list. One example is
virtio-net driver which tries to use small frags for both MTU sized packet and
GSO packet. So this patch introduce skb_coalesce_rx_frag() to do this.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Michael Dalton <mwdalton@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a build warning in skb_checksum() by wrapping the
csum_partial() usage in skb_checksum(). The problem is that on a few
architectures, csum_partial is used with prefix asmlinkage whereas
on most architectures it's not. So fix this up generically as we did
with csum_block_add_ext() to match the signature. Introduced by
2817a336d4 ("net: skb_checksum: allow custom update/combine for
walking skb").
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, skb_checksum walks over 1) linearized, 2) frags[], and
3) frag_list data and calculats the one's complement, a 32 bit
result suitable for feeding into itself or csum_tcpudp_magic(),
but unsuitable for SCTP as we're calculating CRC32c there.
Hence, in order to not re-implement the very same function in
SCTP (and maybe other protocols) over and over again, use an
update() + combine() callback internally to allow for walking
over the skb with different algorithms.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While implementing GSO/TSO support for IPIP, I found skb_segment()
was assuming network header was immediately following mac header.
Its not really true in the case inet_gso_segment() is stacked :
By the time tcp_gso_segment() is called, network header points
to the inner IP header.
Let's instead assume nothing and pick the current offsets found in
original skb, we have skb_headers_offset_update() helper for that.
Also move the csum_start update inside skb_headers_offset_update()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_gro_receive() is currently limited to 16 or 17 MSS per GRO skb,
typically 24616 bytes, because it fills up to MAX_SKB_FRAGS frags.
It's relatively easy to extend the skb using frag_list to allow
more frags to be appended into the last sk_buff.
This still builds very efficient skbs, and allows reaching 45 MSS per
skb.
(45 MSS GRO packet uses one skb plus a frag_list containing 2 additional
sk_buff)
High speed TCP flows benefit from this extension by lowering TCP stack
cpu usage (less packets stored in receive queue, less ACK packets
processed)
Forwarding setups could be hurt, as such skbs will need to be
linearized, although its not a new problem, as GRO could already
provide skbs with a frag_list.
We could make the 65536 bytes threshold a tunable to mitigate this.
(First time we need to linearize skb in skb_needs_linearize(), we could
lower the tunable to ~16*1460 so that following skb_gro_receive() calls
build smaller skbs)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function was only used when a packet was sent to another netns. Now, it can
also be used after tunnel encapsulation or decapsulation.
Only skb_orphan() should not be done when a packet is not crossing netns.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliezer renames several *ll_poll to *busy_poll, but forgets
CONFIG_NET_LL_RX_POLL, so in case of confusion, rename it too.
Cc: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
build_skb() specifies that the data parameter must come from a kmalloc'd
area, this is only true if frag_size equals 0, because then build_skb()
will use kzsize(data) to figure out the actual data size. Update the
comment to reflect that special condition.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inner_protocol was added to struct sk_buff in
0d89d2035f ("MPLS: Add limited GSO support"),
which is scheduled to be included in v3.11.
That patch did not update __copy_skb_header to copy the inner_protocol.
Signed-off-by: Joe Stringer <joe@wand.net.nz>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/freescale/fec_main.c
drivers/net/ethernet/renesas/sh_eth.c
net/ipv4/gre.c
The GRE conflict is between a bug fix (kfree_skb --> kfree_skb_list)
and the splitting of the gre.c code into seperate files.
The FEC conflict was two sets of changes adding ethtool support code
in an "!CONFIG_M5272" CPP protected block.
Finally the sh_eth.c conflict was between one commit add bits set
in the .eesr_err_check mask whilst another commit removed the
.tx_error_check member and assignments.
Signed-off-by: David S. Miller <davem@davemloft.net>
The goal of this new function is to perform all needed cleanup before sending
an skb into another netns.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 68c3316311 ("v4 GRE: Add TCP segmentation offload for GRE")
added a possible skb leak, because it frees only the head of segment
list, in case a skb_linearize() call fails.
This patch adds a kfree_skb_list() helper to fix the bug.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Pravin B Shelar <pshelar@nicira.com>
Cc: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Callers of skb_seq_read() are currently forced to call skb_abort_seq_read()
even when consuming all the data because the last call to skb_seq_read (the
one that returns 0 to indicate the end) fails to unmap the last fragment page.
With this patch callers will be allowed to traverse the SKB data by calling
skb_prepare_seq_read() once and repeatedly calling skb_seq_read() as originally
intended (and documented in the original commit 677e90eda), that is, only call
skb_abort_seq_read() if the sequential read is actually aborted.
Signed-off-by: Wedson Almeida Filho <wedsonaf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 1a37e412a022(net: Use 16bits for *_headers fields of struct
skbuff), skb->*_header are relative to skb->head,
so copy_skb_header() should not call skb_headers_offset_update() now,
and we should pass correct parameter to skb_headers_offset_update() in
pskb_expand_head() and skb_copy_expand().
Signed-off-by: Weiping Pan <panweiping3@gmail.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds an ndo_ll_poll method and the code that supports it.
This method can be used by low latency applications to busy-poll
Ethernet device queues directly from the socket code.
sysctl_net_ll_poll controls how many microseconds to poll.
Default is zero (disabled).
Individual protocol support will be added by subsequent patches.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Tested-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge 'net' bug fixes into 'net-next' as we have patches
that will build on top of them.
This merge commit includes a change from Emil Goode
(emilgoode@gmail.com) that fixes a warning that would
have been introduced by this merge. Specifically it
fixes the pingv6_ops method ipv6_chk_addr() to add a
"const" to the "struct net_device *dev" argument and
likewise update the dummy_ipv6_chk_addr() declaration.
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet spotted that we have to check skb->head instead
of skb->data as skb->head points to the beginning of the
data area of the skbuff. Similarly, we have to initialize the
skb->head pointer, not skb->data in __alloc_skb_head.
After this fix, netlink crashes in the release path of the
sk_buff, so let's fix that as well.
This bug was introduced in (0ebd0ac net: add function to
allocate sk_buff head without data area).
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 1a37e412a0 (net: Use 16bits for *_headers
fields of struct skbuff) converts skb->*_header to u16,
some #if NET_SKBUFF_DATA_USES_OFFSET are now useless,
and to be safe, we could just use "X = (typeof(X)) ~0U;"
as suggested by David.
Cc: David S. Miller <davem@davemloft.net>
Cc: Simon Horman <horms@verge.net.au>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/core/skbuff.c: In function ‘__alloc_skb_head’:
net/core/skbuff.c:203:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
net/core/skbuff.c: In function ‘__alloc_skb’:
net/core/skbuff.c:279:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
net/core/skbuff.c:280:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
net/core/skbuff.c: In function ‘build_skb’:
net/core/skbuff.c:348:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
net/core/skbuff.c:349:2: warning: large integer implicitly truncated to unsigned type [-Woverflow]
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a generic solution to resolve a specific problem that I have observed.
If the encapsulation of an skb changes then ability to offload checksums
may also change. In particular it may be necessary to perform checksumming
in software.
An example of such a case is where a non-GRE packet is received but
is to be encapsulated and transmitted as GRE.
Another example relates to my proposed support for for packets
that are non-MPLS when received but MPLS when transmitted.
The cost of this change is that the value of the csum variable may be
checked when it previously was not. In the case where the csum variable is
true this is pure overhead. In the case where the csum variable is false it
leads to software checksumming, which I believe also leads to correct
checksums in transmitted packets for the cases described above.
Further analysis:
This patch relies on the return value of can_checksum_protocol()
being correct and in turn the return value of skb_network_protocol(),
used to provide the protocol parameter of can_checksum_protocol(),
being correct. It also relies on the features passed to skb_segment()
and in turn to can_checksum_protocol() being correct.
I believe that this problem has not been observed for VLANs because it
appears that almost all drivers, the exception being xgbe, set
vlan_features such that that the checksum offload support for VLAN packets
is greater than or equal to that of non-VLAN packets.
I wonder if the code in xgbe may be an oversight and the hardware does
support checksumming of VLAN packets. If so it may be worth updating the
vlan_features of the driver as this patch will force such checksums to be
performed in software rather than hardware.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When transmit timestamping is enabled at the socket level, record a
timestamp on packets written to a PACKET_TX_RING. Tx timestamps are
always looped to the application over the socket error queue. Software
timestamps are also written back into the packet frame header in the
packet ring.
Reported-by: Paul Chavent <paul.chavent@onera.fr>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a function to allocate a sk_buff head without any data. This will
be used by memory mapped netlink to attach data from the mmaped area
to the skb.
Additionally change skb_release_all() to check whether the skb has a
data area to allow the skb destructor to clear the data pointer in case
only a head has been allocated.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
For untrusted packets with partial checksum, we need to set the transport header
for precise packet length estimation. We can just let skb_pratial_csum_set() to
do this to avoid extra call to skb_flow_dissect() and simplify the caller.
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds inner mac header. This will be used in next patch
to find tunner header length. Header len is required to copy tunnel
header to each gso segment.
This patch does not change any functionality.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function will be used in next VXLAN_GSO patch. This patch does
not change any functionality.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Earlier SG was unset if CSUM was not available for given device to
force skb copy to avoid sending inconsistent csum.
Commit c9af6db4c1 (net: Fix possible wrong checksum generation)
added explicit flag to force copy to fix this issue. Therefore
there is no need to link SG and CSUM, following patch kills this
link between there two features.
This patch is also required following patch in series.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit c9af6db4c1 (net: Fix possible wrong checksum generation)
has a suspicous piece:
- skb_shinfo(skb1)->gso_type = skb_shinfo(skb)->gso_type;
-
+ skb_shinfo(skb)->tx_flags = skb_shinfo(skb1)->tx_flags & SKBTX_SHARED_FRAG;
skb1 is the new skb, therefore should be on the left side of the assignment.
This patch fixes it.
Cc: Pravin B Shelar <pshelar@nicira.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patch adds GRE protocol offload handler so that
skb_gso_segment() can segment GRE packets.
SKB GSO CB is added to keep track of total header length so that
skb_segment can push entire header. e.g. in case of GRE, skb_segment
need to push inner and outer headers to every segment.
New NETIF_F_GRE_GSO feature is added for devices which support HW
GRE TSO offload. Currently none of devices support it therefore GRE GSO
always fall backs to software GSO.
[ Compute pkt_len before ip_local_out() invocation. -DaveM ]
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch cef401de7b (net: fix possible wrong checksum
generation) fixed wrong checksum calculation but it broke TSO by
defining new GSO type but not a netdev feature for that type.
net_gso_ok() would not allow hardware checksum/segmentation
offload of such packets without the feature.
Following patch fixes TSO and wrong checksum. This patch uses
same logic that Eric Dumazet used. Patch introduces new flag
SKBTX_SHARED_FRAG if at least one frag can be modified by
the user. but SKBTX_SHARED_FRAG flag is kept in skb shared
info tx_flags rather than gso_type.
tx_flags is better compared to gso_type since we can have skb with
shared frag without gso packet. It does not link SHARED_FRAG to
GSO, So there is no need to define netdev feature for this.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I get the following build error on next-20130213 due to the following
commit:
commit f05de73bf8 ("skbuff: create
skb_panic() function and its wrappers").
It adds an argument called panic to a function that uses the BUG() macro
which tries to call panic, but the argument masks the panic() function
declaration, resulting in the following error (gcc 4.2.4):
net/core/skbuff.c In function 'skb_panic':
net/core/skbuff.c +126 : error: called object 'panic' is not a function
This is fixed by renaming the argument to msg.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Jean Sacren <sakiwit@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create skb_panic() function in lieu of both skb_over_panic() and
skb_under_panic() so that code duplication would be avoided. Update type
and variable name where necessary.
Jiri Pirko suggested using wrappers so that we would be able to keep the
fruits of the original code.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to address the fact that some devices cannot support the full 32K
frag size we need to have the value accessible somewhere so that we can use it
to do comparisons against what the device can support. As such I am moving
the values out of skbuff.c and into skbuff.h.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/e1000e/ethtool.c
drivers/net/vmxnet3/vmxnet3_drv.c
drivers/net/wireless/iwlwifi/dvm/tx.c
net/ipv6/route.c
The ipv6 route.c conflict is simple, just ignore the 'net' side change
as we fixed the same problem in 'net-next' by eliminating cached
neighbours from ipv6 routes.
The e1000e conflict is an addition of a new statistic in the ethtool
code, trivial.
The vmxnet3 conflict is about one change in 'net' removing a guarding
conditional, whilst in 'net-next' we had a netdev_info() conversion.
The iwlwifi conflict is dealing with a WARN_ON() conversion in
'net-next' vs. a revert happening in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use correct inner offset to set inner_network_offset.
Found by inspection.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pravin Shelar mentioned that GSO could potentially generate
wrong TX checksum if skb has fragments that are overwritten
by the user between the checksum computation and transmit.
He suggested to linearize skbs but this extra copy can be
avoided for normal tcp skbs cooked by tcp_sendmsg().
This patch introduces a new SKB_GSO_SHARED_FRAG flag, set
in skb_shinfo(skb)->gso_type if at least one frag can be
modified by the user.
Typical sources of such possible overwrites are {vm}splice(),
sendfile(), and macvtap/tun/virtio_net drivers.
Tested:
$ netperf -H 7.7.8.84
MIGRATED TCP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to
7.7.8.84 () port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.00 3959.52
$ netperf -H 7.7.8.84 -t TCP_SENDFILE
TCP SENDFILE TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 7.7.8.84 ()
port 0 AF_INET
Recv Send Send
Socket Socket Message Elapsed
Size Size Size Time Throughput
bytes bytes bytes secs. 10^6bits/sec
87380 16384 16384 10.00 3216.80
Performance of the SENDFILE is impacted by the extra allocation and
copy, and because we use order-0 pages, while the TCP_STREAM uses
bigger pages.
Reported-by: Pravin Shelar <pshelar@nicira.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 9ca1b22d6d (net: splice: avoid high order page splitting)
forgot that skb->head could need a copy into several page frags.
This could be the case for loopback traffic mostly.
Also remove now useless skb argument from linear_to_page()
and __splice_segment() prototypes.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
splice() can handle pages of any order, but network code tries hard to
split them in PAGE_SIZE units. Not quite successfully anyway, as
__splice_segment() assumed poff < PAGE_SIZE. This is true for
the skb->data part, not necessarily for the fragments.
This patch removes this logic to give the pages as they are in the skb.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 9ca1b22d6d (net: splice: avoid high order page splitting)
forgot that skb->head could need a copy into several page frags.
This could be the case for loopback traffic mostly.
Also remove now useless skb argument from linear_to_page()
and __splice_segment() prototypes.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have skb_mac_header_was_set() helper to tell if mac_header
was set on a skb. We would like the same for transport_header.
__netif_receive_skb() doesn't reset the transport header if already
set by GRO layer.
Note that network stacks usually reset the transport header anyway,
after pulling the network header, so this change only allows
a followup patch to have more precise qdisc pkt_len computation
for GSO packets at ingress side.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
splice() can handle pages of any order, but network code tries hard to
split them in PAGE_SIZE units. Not quite successfully anyway, as
__splice_segment() assumed poff < PAGE_SIZE. This is true for
the skb->data part, not necessarily for the fragments.
This patch removes this logic to give the pages as they are in the skb.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse detected case where this local function should be static.
It may even allow some compiler optimizations.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking changes from David Miller:
1) Allow to dump, monitor, and change the bridge multicast database
using netlink. From Cong Wang.
2) RFC 5961 TCP blind data injection attack mitigation, from Eric
Dumazet.
3) Networking user namespace support from Eric W. Biederman.
4) tuntap/virtio-net multiqueue support by Jason Wang.
5) Support for checksum offload of encapsulated packets (basically,
tunneled traffic can still be checksummed by HW). From Joseph
Gasparakis.
6) Allow BPF filter access to VLAN tags, from Eric Dumazet and
Daniel Borkmann.
7) Bridge port parameters over netlink and BPDU blocking support
from Stephen Hemminger.
8) Improve data access patterns during inet socket demux by rearranging
socket layout, from Eric Dumazet.
9) TIPC protocol updates and cleanups from Ying Xue, Paul Gortmaker, and
Jon Maloy.
10) Update TCP socket hash sizing to be more in line with current day
realities. The existing heurstics were choosen a decade ago.
From Eric Dumazet.
11) Fix races, queue bloat, and excessive wakeups in ATM and
associated drivers, from Krzysztof Mazur and David Woodhouse.
12) Support DOVE (Distributed Overlay Virtual Ethernet) extensions
in VXLAN driver, from David Stevens.
13) Add "oops_only" mode to netconsole, from Amerigo Wang.
14) Support set and query of VEB/VEPA bridge mode via PF_BRIDGE, also
allow DCB netlink to work on namespaces other than the initial
namespace. From John Fastabend.
15) Support PTP in the Tigon3 driver, from Matt Carlson.
16) tun/vhost zero copy fixes and improvements, plus turn it on
by default, from Michael S. Tsirkin.
17) Support per-association statistics in SCTP, from Michele
Baldessari.
And many, many, driver updates, cleanups, and improvements. Too
numerous to mention individually.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
net/mlx4_en: Add support for destination MAC in steering rules
net/mlx4_en: Use generic etherdevice.h functions.
net: ethtool: Add destination MAC address to flow steering API
bridge: add support of adding and deleting mdb entries
bridge: notify mdb changes via netlink
ndisc: Unexport ndisc_{build,send}_skb().
uapi: add missing netconf.h to export list
pkt_sched: avoid requeues if possible
solos-pci: fix double-free of TX skb in DMA mode
bnx2: Fix accidental reversions.
bna: Driver Version Updated to 3.1.2.1
bna: Firmware update
bna: Add RX State
bna: Rx Page Based Allocation
bna: TX Intr Coalescing Fix
bna: Tx and Rx Optimizations
bna: Code Cleanup and Enhancements
ath9k: check pdata variable before dereferencing it
ath5k: RX timestamp is reported at end of frame
ath9k_htc: RX timestamp is reported at end of frame
...
__copy_skb_header(nskb, p) already copied p->cb[], no need to copy
it again.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support in the kernel for offloading in the NIC Tx and Rx
checksumming for encapsulated packets (such as VXLAN and IP GRE).
For Tx encapsulation offload, the driver will need to set the right bits
in netdev->hw_enc_features. The protocol driver will have to set the
skb->encapsulation bit and populate the inner headers, so the NIC driver will
use those inner headers to calculate the csum in hardware.
For Rx encapsulation offload, the driver will need to set again the
skb->encapsulation flag and the skb->ip_csum to CHECKSUM_UNNECESSARY.
In that case the protocol driver should push the decapsulated packet up
to the stack, again with CHECKSUM_UNNECESSARY. In ether case, the protocol
driver should set the skb->encapsulation flag back to zero. Finally the
protocol driver should have NETIF_F_RXCSUM flag set in its features.
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 2e71a6f808 (net: gro: selective flush of packets) added
a bug for skbs using frag_list. This part of the GRO stack is rarely
used, as it needs skb not using a page fragment for their skb->head.
Most drivers do use a page fragment, but some of them use GFP_KERNEL
allocations for the initial fill of their RX ring buffer.
napi_gro_flush() overwrite skb->prev that was used for these skb to
point to the last skb in frag_list.
Fix this using a separate field in struct napi_gro_cb to point to the
last fragment.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck