Add entries for the 100base-FX full and half duplex supported modes.
$ ethtool eth0
Supported ports: [ FIBRE ]
Supported link modes: 100baseFX/Half 100baseFX/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: 100baseFX/Half 100baseFX/Full
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 100Mb/s
Duplex: Full
Auto-negotiation: off
Port: MII
PHYAD: 1
Transceiver: external
Supports Wake-on: gs
Wake-on: d
SecureOn password: 00:00:00:00:00:00
Current message level: 0x00000000 (0)
Link detected: yes
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Currently drivers have to report their pause frames statistics
via ethtool -S, and there is a wide variety of names used for
these statistics.
Add the two statistics defined in IEEE 802.3x to the standard
API. Create a new ethtool request header flag for including
statistics in the response to GET commands.
Always create the ETHTOOL_A_PAUSE_STATS nest in replies when
flag is set. Testing if driver declares the op is not a reliable
way of checking if any stats will actually be included and therefore
we don't want to give the impression that presence of
ETHTOOL_A_PAUSE_STATS indicates driver support.
Note that this patch does not include PFC counters, which may fit
better in dcbnl? But mostly I don't need them/have a setup to test
them so I haven't looked deeply into exposing them :)
v3:
- add a helper for "uninitializing" stats, rather than a cryptic
memset() (Andrew)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Set IP protocol mask only when IP protocol field is set.
This will allow flow-type ether with vlan rule which don't have
protocol field to apply.
ethtool -N ens5f4 flow-type ether proto 0x8100 vlan 0x600\
m 0x1FFF action 3 loc 16
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
info cannot be NULL here since its being accessed earlier
in the function: nlmsg_parse(info->nlhdr...). Remove this
redundant NULL check.
Signed-off-by: Gaurav Singh <gaurav1086@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
If the genlmsg_put() call in ethnl_default_dumpit() fails, we bail out
without checking if we already have some messages in current skb like we do
with ethnl_default_dump_one() failure later. Therefore if existing messages
almost fill up the buffer so that there is not enough space even for
netlink and genetlink header, we lose all prepared messages and return and
error.
Rather than duplicating the skb->len check, move the genlmsg_put(),
genlmsg_cancel() and genlmsg_end() calls into ethnl_default_dump_one().
This is also more logical as all message composition will be in
ethnl_default_dump_one() and only iteration logic will be left in
ethnl_default_dumpit().
Fixes: 728480f124 ("ethtool: default handlers for GET requests")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Define 100G, 200G and 400G link modes using 100Gbps per lane
LR, ER and FR are defined as a single link mode because they are
using same technology and by design are fully interoperable.
EEPROM content indicates if the module is LR, ER, or FR, and the
user space ethtool decoder is planned to support decoding these
modes in the EEPROM.
Signed-off-by: Meir Lichtinger <meirl@mellanox.com>
CC: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Currently, drivers can only tell whether the link is up/down using
LINKSTATE_GET, but no additional information is given.
Add attributes to LINKSTATE_GET command in order to allow drivers
to expose the user more information in addition to link state to ease
the debug process, for example, reason for link down state.
Extended state consists of two attributes - link_ext_state and
link_ext_substate. The idea is to avoid 'vendor specific' states in order
to prevent drivers to use specific link_ext_state that can be in the future
common link_ext_state.
The substates allows drivers to add more information to the common
link_ext_state. For example, vendor can expose 'Autoneg' as link_ext_state
and add 'No partner detected during force mode' as link_ext_substate.
If a driver cannot pinpoint the extended state with the substate
accuracy, it is free to expose only the extended state and omit the
substate attribute.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Add link extended state attributes.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Fix check in ethtool_rx_flow_rule_create
Fixes: eca4205f9e ("ethtool: add ethtool_rx_flow_spec to flow_rule structure translator")
Signed-off-by: Gaurav Singh <gaurav1086@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Use array_size() helper instead of the open-coded version in
copy_to_user(). These sorts of multiplication factors need to
be wrapped in array_size().
This issue was found with the help of Coccinelle and, audited and fixed
manually.
Addresses-KSPP-ID: https://github.com/KSPP/linux/issues/83
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
This code generates a Smatch warning:
net/ethtool/linkinfo.c:143 ethnl_set_linkinfo()
warn: variable dereferenced before check 'info' (see line 119)
Fortunately, the "info" pointer is never NULL so the check can be
removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
get_coalesce returns 0 or ERRNO, but the return value isn't checked.
The returned coalesce data may be invalid if an ERRNO is set,
therefore better check and propagate the return value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
When getting SQI or maximum SQI value fails in linkstate_prepare_data(), we
must not return without calling ethnl_ops_complete(dev) as that could
result in imbalance between ethtool_ops ->begin() and ->complete() calls.
Fixes: 8066021915 ("ethtool: provide UAPI for PHY Signal Quality Index (SQI)")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
As ethnl_request_ops::reply_size handlers do not include common header
size into calculated/estimated reply size, it needs to be added in
ethnl_default_doit() and ethnl_default_notify() before allocating the
message. On the other hand, strset_reply_size() should not add common
header size.
Fixes: 728480f124 ("ethtool: default handlers for GET requests")
Reported-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Don't call drivers if nothing changed. Netlink code already
contains this logic.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Having a channel config with no ability to RX or TX traffic is
clearly wrong. Check for this in the core so the drivers don't
have to.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
This UAPI is needed for BroadR-Reach 100BASE-T1 devices. Due to lack of
auto-negotiation support, we needed to be able to configure the
MASTER-SLAVE role of the port manually or from an application in user
space.
The same UAPI can be used for 1000BASE-T or MultiGBASE-T devices to
force MASTER or SLAVE role. See IEEE 802.3-2018:
22.2.4.3.7 MASTER-SLAVE control register (Register 9)
22.2.4.3.8 MASTER-SLAVE status register (Register 10)
40.5.2 MASTER-SLAVE configuration resolution
45.2.1.185.1 MASTER-SLAVE config value (1.2100.14)
45.2.7.10 MultiGBASE-T AN control 1 register (Register 7.32)
The MASTER-SLAVE role affects the clock configuration:
-------------------------------------------------------------------------------
When the PHY is configured as MASTER, the PMA Transmit function shall
source TX_TCLK from a local clock source. When configured as SLAVE, the
PMA Transmit function shall source TX_TCLK from the clock recovered from
data stream provided by MASTER.
iMX6Q KSZ9031 XXX
------\ /-----------\ /------------\
| | | | |
MAC |<----RGMII----->| PHY Slave |<------>| PHY Master |
|<--- 125 MHz ---+-<------/ | | \ |
------/ \-----------/ \------------/
^
\-TX_TCLK
-------------------------------------------------------------------------------
Since some clock or link related issues are only reproducible in a
specific MASTER-SLAVE-role, MAC and PHY configuration, it is beneficial
to provide generic (not 100BASE-T1 specific) interface to the user space
for configuration flexibility and trouble shooting.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Conflicts:
drivers/net/phy/phy.c
Implement TSINFO_GET request to get timestamping information for a network
device. This is traditionally available via ETHTOOL_GET_TS_INFO ioctl
request.
Move part of ethtool_get_ts_info() into common.c so that ioctl and netlink
code use the same logic to get timestamping information from the device.
v3: use "TSINFO" rather than "TIMESTAMP", suggested by Richard Cochran
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Conflicts:
net/ethtool/common.c
Add three string sets related to timestamping information:
ETH_SS_SOF_TIMESTAMPING: SOF_TIMESTAMPING_* flags
ETH_SS_TS_TX_TYPES: timestamping Tx types
ETH_SS_TS_RX_FILTERS: timestamping Rx filters
These will be used for TIMESTAMP_GET request.
v2: avoid compiler warning ("enumeration value not handled in switch")
in net_hwtstamp_validate()
v3: omit dash in Tx type names ("one-step-*" -> "onestep-*"), suggested by
Richard Cochran
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Send ETHTOOL_MSG_EEE_NTF notification whenever EEE settings of a network
device are modified using ETHTOOL_MSG_EEE_SET netlink message or
ETHTOOL_SEEE ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Implement EEE_SET netlink request to set EEE settings of a network device.
These are traditionally set with ETHTOOL_SEEE ioctl request.
The netlink interface allows setting the EEE status for all link modes
supported by kernel but only first 32 link modes can be set at the moment
as only those are supported by the ethtool_ops callback.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Implement EEE_GET request to get EEE settings of a network device. These
are traditionally available via ETHTOOL_GEEE ioctl request.
The netlink interface allows reporting EEE status for all link modes
supported by kernel but only first 32 link modes are provided at the moment
as only those are reported by the ethtool_ops callback and drivers.
v2: fix alignment (whitespace only)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Send ETHTOOL_MSG_PAUSE_NTF notification whenever pause parameters of
a network device are modified using ETHTOOL_MSG_PAUSE_SET netlink message
or ETHTOOL_SPAUSEPARAM ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Implement PAUSE_SET netlink request to set pause parameters of a network
device. Thease are traditionally set with ETHTOOL_SPAUSEPARAM ioctl
request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Implement PAUSE_GET request to get pause parameters of a network device.
These are traditionally available via ETHTOOL_GPAUSEPARAM ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Send ETHTOOL_MSG_COALESCE_NTF notification whenever coalescing parameters
of a network device are modified using ETHTOOL_MSG_COALESCE_SET netlink
message or ETHTOOL_SCOALESCE ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Implement COALESCE_SET netlink request to set coalescing parameters of
a network device. These are traditionally set with ETHTOOL_SCOALESCE ioctl
request. This commit adds only support for device coalescing parameters,
not per queue coalescing parameters.
Like the ioctl implementation, the generic ethtool code checks if only
supported parameters are modified; if not, first offending attribute is
reported using extack.
v2: fix alignment (whitespace only)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Implement COALESCE_GET request to get coalescing parameters of a network
device. These are traditionally available via ETHTOOL_GCOALESCE ioctl
request. This commit adds only support for device coalescing parameters,
not per queue coalescing parameters.
Omit attributes with zero values unless they are declared as supported
(i.e. the corresponding bit in ethtool_ops::supported_coalesce_params is
set).
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Andrew noticed that some handlers for *_SET commands leak a netdev
reference if required ethtool_ops callbacks do not exist. One of them is
ethnl_set_privflags(), a simple reproducer would be e.g.
ip link add veth1 type veth peer name veth2
ethtool --set-priv-flags veth1 foo on
ip link del veth1
Make sure dev_put() is called when ethtool_ops check fails.
Fixes: f265d79959 ("ethtool: set device private flags with PRIVFLAGS_SET request")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Currently, ethtool feature mask for checksum command is ORed with
NETIF_F_FCOE_CRC_BIT, which is bit's position number, instead of the
actual feature bit - NETIF_F_FCOE_CRC.
The invalid bitmask here might affect unrelated features when toggling
TX checksumming. For example, TX checksumming is always mistakenly
reported as enabled on the netdevs tested (mlx5, virtio_net).
Fixes: f70bb06563 ("ethtool: update mapping of features to legacy ioctl requests")
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Andrew noticed that some handlers for *_SET commands leak a netdev
reference if required ethtool_ops callbacks do not exist. A simple
reproducer would be e.g.
ip link add veth1 type veth peer name veth2
ethtool -s veth1 wol g
ip link del veth1
Make sure dev_put() is called when ethtool_ops check fails.
v2: add Fixes tags
Fixes: a53f3d41e4 ("ethtool: set link settings with LINKINFO_SET request")
Fixes: bfbcfe2032 ("ethtool: set link modes related data with LINKMODES_SET request")
Fixes: e54d04e3af ("ethtool: set message mask with DEBUG_SET request")
Fixes: 8d425b19b3 ("ethtool: set wake-on-lan settings with WOL_SET request")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Send ETHTOOL_MSG_CHANNELS_NTF notification whenever channel counts of
a network device are modified using ETHTOOL_MSG_CHANNELS_SET netlink
message or ETHTOOL_SCHANNELS ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Implement CHANNELS_SET netlink request to set channel counts of a network
device. These are traditionally set with ETHTOOL_SCHANNELS ioctl request.
Like the ioctl implementation, the generic ethtool code checks if supplied
values do not exceed driver defined limits; if they do, first offending
attribute is reported using extack. Checks preventing removing channels
used for RX indirection table or zerocopy AF_XDP socket are also
implemented.
Move ethtool_get_max_rxfh_channel() helper into common.c so that it can be
used by both ioctl and netlink code.
v2:
- fix netdev reference leak in error path (found by Jakub Kicinsky)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Implement CHANNELS_GET request to get channel counts of a network device.
These are traditionally available via ETHTOOL_GCHANNELS ioctl request.
Omit attributes for channel types which are not supported by driver or
device (zero reported for maximum).
v2: (all suggested by Jakub Kicinski)
- minor cleanup in channels_prepare_data()
- more descriptive channels_reply_size()
- omit attributes with zero max count
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Send ETHTOOL_MSG_RINGS_NTF notification whenever ring sizes of a network
device are modified using ETHTOOL_MSG_RINGS_SET netlink message or
ETHTOOL_SRINGPARAM ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Implement RINGS_SET netlink request to set ring sizes of a network device.
These are traditionally set with ETHTOOL_SRINGPARAM ioctl request.
Like the ioctl implementation, the generic ethtool code checks if supplied
values do not exceed driver defined limits; if they do, first offending
attribute is reported using extack.
v2:
- fix netdev reference leak in error path (found by Jakub Kicinsky)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Implement RINGS_GET request to get ring sizes of a network device. These
are traditionally available via ETHTOOL_GRINGPARAM ioctl request.
Omit attributes for ring types which are not supported by driver or device
(zero reported for maximum).
v2: (all suggested by Jakub Kicinski)
- minor cleanup in rings_prepare_data()
- more descriptive rings_reply_size()
- omit attributes with zero max size
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Send ETHTOOL_MSG_PRIVFLAGS_NTF notification whenever private flags of
a network device are modified using ETHTOOL_MSG_PRIVFLAGS_SET netlink
message or ETHTOOL_SPFLAGS ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Implement PRIVFLAGS_SET netlink request to set private flags of a network
device. These are traditionally set with ETHTOOL_SPFLAGS ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Implement PRIVFLAGS_GET request to get private flags for a network device.
These are traditionally available via ETHTOOL_GPFLAGS ioctl request.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Send ETHTOOL_MSG_FEATURES_NTF notification whenever network device features
are modified using ETHTOOL_MSG_FEATURES_SET netlink message, ethtool ioctl
request or any other way resulting in call to netdev_update_features() or
netdev_change_features()
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Implement FEATURES_SET netlink request to set network device features.
These are traditionally set using ETHTOOL_SFEATURES ioctl request.
Actual change is subject to netdev_change_features() sanity checks so that
it can differ from what was requested. Unlike with most other SET requests,
in addition to error code and optional extack, kernel provides an optional
reply message (ETHTOOL_MSG_FEATURES_SET_REPLY) in the same format but with
different semantics: information about difference between user request and
actual result and difference between old and new state of dev->features.
This reply message can be suppressed by setting ETHTOOL_FLAG_OMIT_REPLY
flag in request header.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Unlike other SET type commands, modifying netdev features is required to
provide a reply telling userspace what was actually changed, compared to
what was requested. For that purpose, the "modified" flag provided by
ethnl_update_bitset() is not sufficient, we need full information which
bits were requested to change.
Therefore provide ethnl_parse_bitset() returning effective value and mask
bitmaps equivalent to the contents of a bitset nested attribute.
v2: use non-atomic __set_bit() (suggested by David Miller)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Implement FEATURES_GET request to get network device features. These are
traditionally available via ETHTOOL_GFEATURES ioctl request.
v2:
- style cleanup suggested by Jakub Kicinski
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Legacy ioctl request like ETHTOOL_GTXCSUM are still used by ethtool utility
to get values of legacy flags (which rather work as feature groups). These
are calculated from values of actual features and request to set them is
implemented as an attempt to set all features mapping to them but there are
two inconsistencies:
- tx-checksum-fcoe-crc is shown under tx-checksumming but NETIF_F_FCOE_CRC
is not included in ETHTOOL_GTXCSUM/ETHTOOL_STXCSUM
- tx-scatter-gather-fraglist is shown under scatter-gather but
NETIF_F_FRAGLIST is not included in ETHTOOL_GSG/ETHTOOL_SSG
As the mapping in ethtool output is more correct from logical point of
view, fix ethtool_get_feature_mask() to match it.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Andrew Lunn pointed out that even if it's documented that
ethnl_parse_header() takes reference to network device if it fills it
into the target structure, its name doesn't make it apparent so that
corresponding dev_put() looks like mismatched.
Rename the function ethnl_parse_header_dev_get() to indicate that it
takes a reference.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Linux supports 22 different interrupt coalescing parameters.
No driver implements them all. Some drivers just ignore the
ones they don't support, while others have to carry a long
list of checks to reject unsupported settings.
To simplify the drivers add the ability to specify inside
ethtool_ops which parameters are supported and let the core
reject attempts to set any other one.
This commit makes the mechanism an opt-in, only drivers which
set ethtool_opts->coalesce_types to a non-zero value will have
the checks enforced.
The same mask is used for global and per queue settings.
v3: - move the (temporary) check if driver defines types
earlier (Michal)
- rename used_types -> nonzero_params, and
coalesce_types -> supported_coalesce_params (Alex)
- use EOPNOTSUPP instead of EINVAL (Andrew, Michal)
Leaving the long series of ifs for now, it seems nice to
be able to grep for the field and flag names. This will
probably have to be revisited once netlink support lands.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Add support for low latency Reed Solomon FEC as LLRS.
The LL-FEC is defined by the 25G/50G ethernet consortium,
in the document titled "Low Latency Reed Solomon Forward Error Correction"
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
CC: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Syzbot reported that ethnl_compact_sanity_checks() can be tricked into
reading past the end of ETHTOOL_A_BITSET_VALUE and ETHTOOL_A_BITSET_MASK
attributes and even the message by passing a value between (u32)(-31)
and (u32)(-1) as ETHTOOL_A_BITSET_SIZE.
The problem is that DIV_ROUND_UP(attr_nbits, 32) is 0 for such values so
that zero length ETHTOOL_A_BITSET_VALUE will pass the length check but
ethnl_bitmap32_not_zero() check would try to access up to 512 MB of
attribute "payload".
Prevent this overflow byt limiting the bitset size. Technically, compact
bitset format would allow bitset sizes up to almost 2^18 (so that the
nest size does not exceed U16_MAX) but bitsets used by ethtool are much
shorter. S16_MAX, the largest value which can be directly used as an
upper limit in policy, should be a reasonable compromise.
Fixes: 10b518d4e6 ("ethtool: netlink bitset handling")
Reported-by: syzbot+7fd4ed5b4234ab1fdccd@syzkaller.appspotmail.com
Reported-by: syzbot+709b7a64d57978247e44@syzkaller.appspotmail.com
Reported-by: syzbot+983cb8fb2d17a7af549d@syzkaller.appspotmail.com
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: hongrongxuan <hongrongxuan@huawei.com>
Dan Murphy