In each case, the kfree already at the end of the function is also needed
in the error case.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@exists@
local idexpression x;
statement S,S1;
expression E;
identifier fl;
expression *ptr != NULL;
@@
x = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...kfree(x)...+> }
when any
when != true x == NULL
x->fl
...>
(
if (x == NULL) S1
|
if (...) { ... when != x
when forall
(
return \(0\|<+...x...+>\|ptr\);
|
* return ...;
)
}
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This driver uses IW_ESSID_MAX_SIZE when it should
be using IEEE80211_MAX_SSID_LEN instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* remove interrupt.g inclusion from netdevice.h -- not needed
* fixup fallout, add interrupt.h and hardirq.h back where needed.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Nokia N900 the wl1251 consumes the most power when the interface is up
but not associated to access point (that supports PSM). In terms of battery
current consumption, the consumption is ~180 mA higher when the interface is
up but not associated and only ~5 mA higher when associated compared to
interface down and driver not loaded cases.
This patch adds support for the mac80211 idle notifications. Chip is put into
idle very much the same way when entering into PSM by utilizing the Extreme
Low Power (ELP) mode. I.e. idle is entered by setting necessary conditions
in wl1251_ps_set_mode followed by a call to wl1251_ps_elp_sleep.
It seems it is just enough the authorize ELP mode followed by
CMD_DISCONNECT (thanks to Kalle Valo about the idea to use it).
Without disconnect command the chip remains somewhat active and stays
consuming ~20 mA. Idle mode is left by same way than PSM. The wl1251_join
call is used to revert the CMD_DISCONNECT. Without it association to AP
doesn't work when trying second time.
With this patch the interface up but not associated case the battery current
consumption is less than 1 mA higher compared to interface down case.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RFC for WL1251 idle mode support brought a few issues that are worth to
update before adding the idle mode support.
Since the idle mode can reuse the code that is now used in Power Save Mode
(PSM), the flag psm in struct wl1251 is changed to variable station_mode
to be able to distinguish between PSM and idle modes.
As the station mode is different than the power power save mode command
that is sent to chip, the enum wl1251_cmd_ps_mod values are used only when
communicating with the chip and new enum wl1251_station_mode values are used
inside the driver.
Confusing comment about psm and elp relation is removed since the PSM is
actually activated by putting the chip into Entreme Low Power (ELP) mode.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While working on PS I've noticed elp_work is kicking rather often, and
sometimes the chip is put to sleep before 5ms delay expires. This
seems to happen because by the time wl1251_ps_elp_wakeup is called
elp_work might still be pending. After wakeup is done, the processing
may take some time, during which 5ms might expire and elp_work might
get scheduled. In this case, ss soon as 1st thread finishes work and
releases the mutex, elp_work will then put the device to sleep without
5ms delay. In addition 1st thread will queue additional elp_work
needlessly.
Fix this by cancelling work in wl1251_ps_elp_wakeup instead.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl1251_ps_set_elp() only does acx_sleep_auth call and takes the chip
from/to ELP, however all callers of wl1251_ps_set_mode() have already
taken the chip out of ELP and puts it back to ELP when they finish.
This makes ELP calls (and register writes they result in) superfluous.
So remove wl1251_ps_set_elp function and call acx_sleep_auth directly.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The return value of the tx operation is commonly
misused by drivers, leading to errors. All drivers
will drop frames if they fail to TX the frame, and
they must also properly manage the queues (if they
didn't, mac80211 would already warn).
Removing the ability for drivers to return a BUSY
value also allows significant cleanups of the TX
TX handling code in mac80211.
Note that this also fixes a bug in ath9k_htc, the
old "return -1" there was wrong.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Sedat Dilek <sedat.dilek@googlemail.com> [ath5k]
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> [rt2x00]
Acked-by: Larry Finger <Larry.Finger@lwfinger.net> [b43, rtl8187, rtlwifi]
Acked-by: Luciano Coelho <coelho@ti.com> [wl12xx]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The flag isn't very descriptive -- the intention
is that the driver provides a TSF timestamp at
the beginning of the MPDU -- make that clearer
by renaming the flag to RX_FLAG_MACTIME_MPDU.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the rate index rate_idx and preamble flag RX_FLAG_SHORTPRE on received
packets.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable adhoc support in wl1251 driver.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement connection quality monitoring similar to the wl1271 driver.
It triggers ieee80211_cqm_rssi_notify with the corresponding event when
RSSI drops blow RSSI threshold or rises again above the RSSI threshold.
It should be noted that wl1251 doesn't support RSSI hysteresis, instead it
uses RSSI averageing and delays events until a certain count of frames
proved RSSI change.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Port the beacon early termination feature from wl1251 driver version
included in the Maemo Fremantle kernel.
It is enabled when going to power-saving mode and disabled when leaving
power-saving mode.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This implements TX buffer alignment for cloned or too small skb by
copying and replacing the original skb.
Recent changes in wireless-testing seems to make this really necessary.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The queue stopping/waking functionality was broken in a way that could
cause the TX to stall if the right circumstances are met.
The problem was caused by tx_work, which is scheduled on each TX operation.
If the firmware buffer is full, tx_work does nothing. In combinition with
stopped queues or non-continues transfers, tx_work is never scheduled again.
Moreover the low watermark introduced by
9df86e2e70 never takes effect because of some
old code.
Solve this by scheduling tx_work every time tx_queue is non-empty and
firmware buffer is freed on tx_complete.
This also solves a possible but unlikely case: If less frames than the high
watermark are queued, but more than firmware buffer can hold. This results
in queues staying awake but the only scheduled tx_work doesn't transfer all
frames, so the remaining frames are stuck in the queue until more frames
get queued and tx_work is scheduled again.
Signed-off-by: David Gnedt <david.gnedt@davizone.at>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In drivers/net/wireless/wl1251/main.c:wl1251_op_bss_info_changed() we make
a call to ieee80211_beacon_get() which may return NULL, but we do not
check the return value before dereferencing the pointer.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend channel to frequency mapping for 802.11j Japan 4.9GHz band, according to
IEEE802.11 section 17.3.8.3.2 and Annex J. Because there are now overlapping
channel numbers in the 2GHz and 5GHz band we can't map from channel to
frequency without knowing the band. This is no problem as in most contexts we
know the band. In places where we don't know the band (and WEXT compatibility)
we assume the 2GHz band for channels below 14.
This patch does not implement all channel to frequency mappings defined in
802.11, it's just an extension for 802.11j 20MHz channels. 5MHz and 10MHz
channels as well as 802.11y channels have been omitted.
The following drivers have been updated to reflect the API changes:
iwl-3945, iwl-agn, iwmc3200wifi, libertas, mwl8k, rt2x00, wl1251, wl12xx.
The drivers have been compile-tested only.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Brian Prodoehl <bprodoehl@gmail.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No function declared in gpio.h is used here.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl12xx_get_platform_data() returns an ERR_PTR on failure and it never
returns a NULL.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make use the newly added method to pass platform data for wl1251 too.
This allows to eliminate some redundant code.
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add runtime PM support, similar to how it's done for wl1271.
This allows to power down the card when the driver is loaded but
network is not in use.
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Call interface specific power callback before calling board specific
one. Also allow that callback to fail. This is how it's done for
wl1271 and will be used for runtime_pm support.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wl1251 move accidently renamed wl1251_sdio and wl1251_spi
modules to just sdio and spi. Restore proper module names.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1699 commits)
bnx2/bnx2x: Unsupported Ethtool operations should return -EINVAL.
vlan: Calling vlan_hwaccel_do_receive() is always valid.
tproxy: use the interface primary IP address as a default value for --on-ip
tproxy: added IPv6 support to the socket match
cxgb3: function namespace cleanup
tproxy: added IPv6 support to the TPROXY target
tproxy: added IPv6 socket lookup function to nf_tproxy_core
be2net: Changes to use only priority codes allowed by f/w
tproxy: allow non-local binds of IPv6 sockets if IP_TRANSPARENT is enabled
tproxy: added tproxy sockopt interface in the IPV6 layer
tproxy: added udp6_lib_lookup function
tproxy: added const specifiers to udp lookup functions
tproxy: split off ipv6 defragmentation to a separate module
l2tp: small cleanup
nf_nat: restrict ICMP translation for embedded header
can: mcp251x: fix generation of error frames
can: mcp251x: fix endless loop in interrupt handler if CANINTF_MERRF is set
can-raw: add msg_flags to distinguish local traffic
9p: client code cleanup
rds: make local functions/variables static
...
Fix up conflicts in net/core/dev.c, drivers/net/pcmcia/smc91c92_cs.c and
drivers/net/wireless/ath/ath9k/debug.c as per David
wl1271 driver is under heavy development but on the other hand the older
wl1251 driver is currently considered more as a legacy driver. To make it
easier to develop wl1271 features move wl1251 to it's own directory,
drivers/net/wireless/wl1251.
There are no functional changes, only moving of files. One regression
is that Kconfig won't be updated automatically and user needs to enable
wl1251 manually with an older config file.
Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In preparation of moving wl1251 out from drivers/net/wireless/wl12xx
create a separate copy of wl12xx_80211.h.
This file should not even exist, we should instead use generic ieee80211
definitions. This will be fixed in the future so that the file can
be removed.
Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville