The data pin 0-7 of the NAND controller are actually missing from
the nand pinctrl group, so we fix it here.
Fixes: 0f15f500ff ("pinctrl: meson: Add GXL pinctrl definitions")
Reported-by: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This change prepare the introduction of new meson SoC. This new SoC will
share the same gpio/pinconf registers but the pinmux part will be
different. While the format of the data associated with each pinmux group
will change, the way to handle pinmuxing will be similar.
To deal with this new situation, the meson_pmx_struture is kept but the
data associated to it is now generic. This allows to reuse the basic
functions which would otherwise be copy/pasted in each pinmux driver
(such as getting the name a count of groups and functions) Only the
functions actually using this specific data is taken out of the common
code and is handling the SoC pinmuxing
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When meson pinctrl is enabled, all meson platforms pinctrl drivers are
built in the kernel, with a significant amount of data.
This leads to situation where pinctrl drivers targeting an architecture
are also compiled and shipped on another one (ex: meson8 - ARM - compiled
and shipped on ARM64 builds). This is a waste of memory we can easily
avoid.
This change makes 4 pinctrl drivers (1 per SoC) out the original single
driver, allowing to compile and ship only the ones required.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add TEST_N pinmux for channel 6 and 7 of the i2s output
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On meson-gx platforms, TEST_N has been incorrectly declared in the EE
controller while it belongs to AO controller.
Move the pin to the appropriate controller
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pin_base was used with the manually set pin offset in meson pinctrl. This
is no longer the case, pin_base is 0 on every meson pinctrl controllers
and should go away.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Offset on meson pinctrl and gpios is something that was carried from the
vendor driver, where there is a weird link between the 2
controllers. Since these 2 controllers are independent, this offset adds
an unnecessary complexity.
This patch remove this manually set offset and rely on pinctrl to figure
out the gpio base offset
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add Tsin A pins to bank DV and X.
We don't have a driver for the tsin yet but since the tsin A pinmux is
enabled by default at boot time, declaring this pinmux is required to
properly operate on GPIOX.
Without this change, GPIOX 8, 9, 10 and 11 can't be driven as GPIO output
as the tsin A seems to have priority.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add GPIO interrupt information to pinctrl data. Added to the original
version from Jerome was data for Meson GXL.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Amlogic Meson GXL SoCs embeds an 10/100 Ethernet PHY, this patchs enables
the Link and Activity LEDs signals.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the AO and EE domain CEC pins for the Amlogic Meson GXL SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AO SPDIF pins were incorrectly defined with the EE pin offset.
Fixes: b840d649f9 ("pinctrl: meson: gxl: add spdif output pins")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AO I2S pins were incorrectly defined with the EE pin offset.
Fixes: 2899adf042 ("pinctrl: meson: gxl: add i2s output pins")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SPICC controller has dedicated SPI pins, this patchs add the pins
definition in the GXL pinctrl driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix some inverted bit numbers in some pinctrl groups and add missing pins
and groups to be in pair with the GXBB pinctrl pins definition.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for the missing PWM pins on Meson GXL SoCs, namely:
- PWM_A
- PWM_B
- PWM_C
- PWM_F (GPIOX_7 and GPIOCLK_1 can be selected as output)
- PWM_AO_A (GPIOAO_3 and GPIOAO_8 can be selected as output)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for the pwm_ao_b pin. Unfortunately the registers for
the pwm_ao pins are not documented at all. The source for the pwm_ao_b
pin from this patch is the Khadas VIM GPL kernel source, which sets bit
3 and unsets bits 4 and 31 to enable the PWM LEDs.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GXBB and GXL/GXM pinctrl drivers had a configuration which conflicts
with uart_ao_a. According to the GXBB ("S905") datasheet the AO UART
functions are:
- GPIOAO_0: Func1 = UART_TX_AO_A (bit 12), Func2 = UART_TX_AO_B (bit 26)
- GPIOAO_1: Func1 = UART_RX_AO_A (bit 11), Func2 = UART_RX_AO_B (bit 25)
- GPIOAO_4: Func2 = UART_TX_AO_B (bit 24)
- GPIOAO_5: Func2 = UART_RX_AO_B (bit 25)
The existing definition for uart_AO_A already uses GPIOAO_0 and GPIOAO_1.
The old definition of uart_AO_B however was broken, as it used GPIOAO_0
for TX (which would be fine) and two pins (GPIOAO_1 and GPIOAO_5) for RX
(which does not make any sense).
This fixes the uart_AO_B configuration by moving it to GPIOAO_4 and
GPIOAO_5 (it would be possible to use GPIOAO_0 and GPIOAO_1 in theory,
but all existing hardware uses uart_AO_A there).
The fix for GXBB and GXL/GXM is identical since it seems that these
specific pins are identical on both SoC variants.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinctrl functions for HDMI HPD pin and DDC pins on Amlogic Meson
GXL and GXBB SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for the Amlogic Meson GXL SoC, this is a partially complete
definition only based on the Amlogic Vendor tree.
This definition differs a lot from the GXBB and needs a separate entry.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Yixun Lan