While handling netdevice events, br_device_event() sometimes uses
br_stp_(disable|enable)_port which unconditionally send a notification,
but then a second notification for the same event is sent at the end of
the br_device_event() function. To avoid sending duplicate notifications
in such cases, check if one has already been sent (i.e.
br_stp_enable/disable_port have been called).
The patch is based on a change by Satish Ashok.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a couple new functions to allow querying FDB and vlan settings of a
bridge.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Roopa noted today the biggest source of problems when configuring
bridge and ports is that the bridge MTU keeps changing automatically on
port events (add/del/changemtu). That leads to inconsistent behaviour
and network config software needs to chase the MTU and fix it on each
such event. Let's improve on that situation and allow for the user to
set any MTU within ETH_MIN/MAX limits, but once manually configured it
is the user's responsibility to keep it correct afterwards.
In case the MTU isn't manually set - the behaviour reverts to the
previous and the bridge follows the minimum MTU.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently the bridge was changed to automatically set maximum MTU on port
events (add/del/changemtu) when vlan filtering is enabled, but that
actually changes behaviour in a way which breaks some setups and can lead
to packet drops. In order to still allow that maximum to be set while being
compatible, we add the ability for the user to tune the bridge MTU up to
the maximum when vlan filtering is enabled, but that has to be done
explicitly and all port events (add/del/changemtu) lead to resetting that
MTU to the minimum as before.
Suggested-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the bridge is allowing multiple VLANs, some VLANs may have
different MTUs. Instead of choosing the minimum MTU for the
bridge interface, choose the maximum MTU of the bridge members.
With this the user only needs to set a larger MTU on the member
ports that are participating in the large MTU VLANS.
Signed-off-by: Chas Williams <3chas3@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return statements in functions returning bool should use
true/false instead of 1/0.
This issue was detected with the help of Coccinelle.
Fixes: 85b3526932 ("bridge: Fix build error when IGMP_SNOOPING is not enabled")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch the bridge used a fixed 256 element hash table which
was fine for small use cases (in my tests it starts to degrade
above 1000 entries), but it wasn't enough for medium or large
scale deployments. Modern setups have thousands of participants in a
single bridge, even only enabling vlans and adding a few thousand vlan
entries will cause a few thousand fdbs to be automatically inserted per
participating port. So we need to scale the fdb table considerably to
cope with modern workloads, and this patch converts it to use a
rhashtable for its operations thus improving the bridge scalability.
Tests show the following results (10 runs each), at up to 1000 entries
rhashtable is ~3% slower, at 2000 rhashtable is 30% faster, at 3000 it
is 2 times faster and at 30000 it is 50 times faster.
Obviously this happens because of the properties of the two constructs
and is expected, rhashtable keeps pretty much a constant time even with
10000000 entries (tested), while the fixed hash table struggles
considerably even above 10000.
As a side effect this also reduces the net_bridge struct size from 3248
bytes to 1344 bytes. Also note that the key struct is 8 bytes.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The boolean mglist indicates the host has joined a particular
multicast group on the bridge interface. It is badly named, obscuring
what is means. Rename it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the bridge device doesn't generate any notifications upon vlan
modifications on itself because it doesn't use the generic bridge
notifications.
With the recent changes we know if anything was modified in the vlan config
thus we can generate a notification when necessary for the bridge device
so add support to br_ifinfo_notify() similar to how other combined
functions are done - if port is present it takes precedence, otherwise
notify about the bridge. I've explicitly marked the locations where the
notification should be always for the port by setting bridge to NULL.
I've also taken the liberty to rearrange each modified function's local
variables in reverse xmas tree as well.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch there was no way to tell if the vlan add operation
actually changed anything, thus we would always generate a notification
on adds. Let's make the notifications more precise and generate them
only if anything changed, so use the new bool parameter to signal that the
vlan was updated. We cannot return an error because there are valid use
cases that will be broken (e.g. overlapping range add) and also we can't
risk masking errors due to calls into drivers for vlan add which can
potentially return anything.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch avoids flooding and proxies ndisc packets
for BR_NEIGH_SUPPRESS ports.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch avoids flooding and proxies arp packets
for BR_NEIGH_SUPPRESS ports.
Moves existing br_do_proxy_arp to br_do_proxy_suppress_arp
to support both proxy arp and neigh suppress.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new bridge port flag BR_NEIGH_SUPPRESS to
suppress arp and nd flood on bridge ports. It implements
rfc7432, section 10.
https://tools.ietf.org/html/rfc7432#section-10
for ethernet VPN deployments. It is similar to the existing
BR_PROXYARP* flags but has a few semantic differences to conform
to EVPN standard. Unlike the existing flags, this new flag suppresses
flood of all neigh discovery packets (arp and nd) to tunnel ports.
Supports both vlan filtering and non-vlan filtering bridges.
In case of EVPN, it is mainly used to avoid flooding
of arp and nd packets to tunnel ports like vxlan.
This patch adds netlink and sysfs support to set this bridge port
flag.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass extack arg to br_add_if. Add messages for a couple of failures
and pass arg to netdev_master_upper_dev_link.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to be able to transparently forward most link-local frames via
tunnels (e.g. vxlan, qinq). Currently the bridge's group_fwd_mask has a
mask which restricts the forwarding of STP and LACP, but we need to be able
to forward these over tunnels and control that forwarding on a per-port
basis thus add a new per-port group_fwd_mask option which only disallows
mac pause frames to be forwarded (they're always dropped anyway).
The patch does not change the current default situation - all of the others
are still restricted unless configured for forwarding.
We have successfully tested this patch with LACP and STP forwarding over
VxLAN and qinq tunnels.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using ifdef in the C file.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Suggested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Tested-by: Yotam Gigi <yotamg@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new static FDB is added to the bridge a notification is sent to
the driver for offload. In case of successful offload the driver should
notify the bridge back, which in turn should mark the FDB as offloaded.
Currently, externally learned is equivalent for being offloaded which is
not correct due to the fact that FDBs which are added from user-space are
also marked as externally learned. In order to specify if an FDB was
successfully offloaded a new flag is introduced.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the bridge doesn't notify the underlying devices about new
FDBs learned. The FDB sync is placed on the switchdev notifier chain
because devices may potentially learn FDB that are not directly related
to their ports, for example:
1. Mixed SW/HW bridge - FDBs that point to the ASICs external devices
should be offloaded as CPU traps in order to
perform forwarding in slow path.
2. EVPN - Externally learned FDBs for the vtep device.
Notification is sent only about static FDB add/del. This is done due
to fact that currently this is the only scenario supported by switch
drivers.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is done as a preparation to moving the switchdev notifier chain
to be atomic. The FDB external learning should be called under rtnl
or rcu.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the flood, learning and learning_sync port attributes are
offloaded by setting the SELF flag. Add support for offloading the
flood and learning attribute through the bridge code. In case of
setting an unsupported flag on a offloded port the operation will
fail.
The learning_sync attribute doesn't have any software representation
and cannot be offloaded through the bridge code.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's useful for drivers supporting bridge offload to be able to query
the bridge's VLAN filtering state.
Currently, upon enslavement to a bridge master, the offloading driver
will only learn about the bridge's VLAN filtering state after the bridge
device was already linked with its slave.
Being able to query the bridge's VLAN filtering state allows such
drivers to forbid enslavement in case resource couldn't be allocated for
a VLAN-aware bridge and also choose the correct initialization routine
for the enslaved port, which is dependent on the bridge type.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the bridge driver implements an ndo_init(), it was missing a
symmetric ndo_uninit(), causing the different de-initialization
operations to be scattered around its dellink() and destructor().
Implement a symmetric ndo_uninit() and remove the overlapping operations
from its dellink() and destructor().
This is a prerequisite for the next patch, as it allows us to have a
proper cleanup upon changelink() failure during the bridge's newlink().
Fixes: b6677449df ("bridge: netlink: call br_changelink() during br_dev_newlink()")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrei reported a false alarm of lockdep at net/bridge/br_fdb.c:109,
this is because in Andrei's case, a spin_bug() was already triggered
before this, therefore the debug_locks is turned off, lockdep_is_held()
is no longer accurate after that. We should use lockdep_assert_held_once()
instead of lockdep_is_held() to respect debug_locks.
Fixes: 410b3d48f5 ("bridge: fdb: add proper lock checks in searching functions")
Reported-by: Andrei Vagin <avagin@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to avoid new errors add checks to br_fdb_find and fdb_find_rcu
functions. The first requires hash_lock, the second obviously RCU.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch we had 3 different fdb searching functions which was
confusing. This patch reduces all of them to one - fdb_find_rcu(), and
two flavors: br_fdb_find() which requires hash_lock and br_fdb_find_rcu
which requires RCU. This makes it clear what needs to be used, we also
remove two abusers of __br_fdb_get which called it under hash_lock and
replace them with br_fdb_find().
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fdb's used and updated fields are written to on every packet forward and
packet receive respectively. Thus if we are receiving packets from a
particular fdb, they'll cause false-sharing with everyone who has looked
it up (even if it didn't match, since mac/vid share cache line!). The
"used" field is even worse since it is updated on every packet forward
to that fdb, thus the standard config where X ports use a single gateway
results in 100% fdb false-sharing. Note that this patch does not prevent
the last scenario, but it makes it better for other bridge participants
which are not using that fdb (and are only doing lookups over it).
The point is with this move we make sure that only communicating parties
get the false-sharing, in a later patch we'll show how to avoid that too.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the fdb garbage collector to a workqueue which fires at least 10
milliseconds apart and cleans chain by chain allowing for other tasks
to run in the meantime. When having thousands of fdbs the system is much
more responsive. Most importantly remove the need to check if the
matched entry has expired in __br_fdb_get that causes false-sharing and
is completely unnecessary if we cleanup entries, at worst we'll get 10ms
of traffic for that entry before it gets deleted.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move around net_bridge so the vlan fields are in the beginning since
they're checked on every packet even if vlan filtering is disabled.
For the port move flags & vlan group to the beginning, so they're in the
same cache line with the port's state (both flags and state are checked
on each packet).
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- ingress hook:
- if port is a tunnel port, use tunnel info in
attached dst_metadata to map it to a local vlan
- egress hook:
- if port is a tunnel port, use tunnel info attached to
vlan to set dst_metadata on the skb
CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to attach per vlan tunnel info dst
metadata. This enables bridge driver to map vlan to tunnel_info
at ingress and egress. It uses the kernel dst_metadata infrastructure.
The initial use case is vlan to vni bridging, but the api is generic
to extend to any tunnel_info in the future:
- Uapi to configure/unconfigure/dump per vlan tunnel data
- netlink functions to configure vlan and tunnel_info mapping
- Introduces bridge port flag BR_LWT_VLAN to enable attach/detach
dst_metadata to bridged packets on ports. off by default.
- changes to existing code is mainly refactor some existing vlan
handling netlink code + hooks for new vlan tunnel code
- I have kept the vlan tunnel code isolated in separate files.
- most of the netlink vlan tunnel code is handling of vlan-tunid
ranges (follows the vlan range handling code). To conserve space
vlan-tunid by default are always dumped in ranges if applicable.
Use case:
example use for this is a vxlan bridging gateway or vtep
which maps vlans to vn-segments (or vnis).
iproute2 example (patched and pruned iproute2 output to just show
relevant fdb entries):
example shows same host mac learnt on two vni's and
vlan 100 maps to vni 1000, vlan 101 maps to vni 1001
before (netdev per vni):
$bridge fdb show | grep "00:02:00:00:00:03"
00:02:00:00:00:03 dev vxlan1001 vlan 101 master bridge
00:02:00:00:00:03 dev vxlan1001 dst 12.0.0.8 self
00:02:00:00:00:03 dev vxlan1000 vlan 100 master bridge
00:02:00:00:00:03 dev vxlan1000 dst 12.0.0.8 self
after this patch with collect metdata in bridged mode (single netdev):
$bridge fdb show | grep "00:02:00:00:00:03"
00:02:00:00:00:03 dev vxlan0 vlan 101 master bridge
00:02:00:00:00:03 dev vxlan0 src_vni 1001 dst 12.0.0.8 self
00:02:00:00:00:03 dev vxlan0 vlan 100 master bridge
00:02:00:00:00:03 dev vxlan0 src_vni 1000 dst 12.0.0.8 self
CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements an optional, per bridge port flag and feature to deliver
multicast packets to any host on the according port via unicast
individually. This is done by copying the packet per host and
changing the multicast destination MAC to a unicast one accordingly.
multicast-to-unicast works on top of the multicast snooping feature of
the bridge. Which means unicast copies are only delivered to hosts which
are interested in it and signalized this via IGMP/MLD reports
previously.
This feature is intended for interface types which have a more reliable
and/or efficient way to deliver unicast packets than broadcast ones
(e.g. wifi).
However, it should only be enabled on interfaces where no IGMPv2/MLDv1
report suppression takes place. This feature is disabled by default.
The initial patch and idea is from Felix Fietkau.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[linus.luessing@c0d3.blue: various bug + style fixes, commit message]
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
802.1D [1] specifies that the bridges must use a short value to age out
dynamic entries in the Filtering Database for a period, once a topology
change has been communicated by the root bridge.
Add a bridge_ageing_time member in the net_bridge structure to store the
bridge ageing time value configured by the user (ioctl/netlink/sysfs).
If we are using in-kernel STP, shorten the ageing time value to twice
the forward delay used by the topology when the topology change flag is
set. When the flag is cleared, restore the configured ageing time.
[1] "8.3.5 Notifying topology changes ",
http://profesores.elo.utfsm.cl/~agv/elo309/doc/802.1D-1998.pdf
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SWITCHDEV_ATTR_ID_BRIDGE_AGEING_TIME switchdev attr is actually set
when initializing a bridge port, and when configuring the bridge ageing
time from ioctl/netlink/sysfs.
Add a __set_ageing_time helper to offload the ageing time to physical
switches, and add the SWITCHDEV_F_DEFER flag since it can be called
under bridge lock.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds basic support for MLDv2 queries, the default is MLDv1
as before. A new multicast option - multicast_mld_version, adds the
ability to change it between 1 and 2 via netlink and sysfs.
The MLD option is disabled if CONFIG_IPV6 is disabled.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds basic support for IGMPv3 queries, the default is IGMPv2
as before. A new multicast option - multicast_igmp_version, adds the
ability to change it between 2 and 3 via netlink and sysfs. The option
struct member is in a 4 byte hole in net_bridge.
There also a few minor style adjustments in br_multicast_new_group and
br_multicast_add_group.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the unicast flag and introduce an exact pkt_type. That would help us
for the upcoming per-port multicast flood flag and also slightly reduce the
tests in the input fast path.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fdb dumps spanning multiple skb's currently restart from the first
interface again for every skb. This results in unnecessary
iterations on the already visited interfaces and their fdb
entries. In large scale setups, we have seen this to slow
down fdb dumps considerably. On a system with 30k macs we
see fdb dumps spanning across more than 300 skbs.
To fix the problem, this patch replaces the existing single fdb
marker with three markers: netdev hash entries, netdevs and fdb
index to continue where we left off instead of restarting from the
first netdev. This is consistent with link dumps.
In the process of fixing the performance issue, this patch also
re-implements fix done by
commit 472681d57a ("net: ndo_fdb_dump should report -EMSGSIZE to rtnl_fdb_dump")
(with an internal fix from Wilson Kok) in the following ways:
- change ndo_fdb_dump handlers to return error code instead
of the last fdb index
- use cb->args strictly for dump frag markers and not error codes.
This is consistent with other dump functions.
Below results were taken on a system with 1000 netdevs
and 35085 fdb entries:
before patch:
$time bridge fdb show | wc -l
15065
real 1m11.791s
user 0m0.070s
sys 1m8.395s
(existing code does not return all macs)
after patch:
$time bridge fdb show | wc -l
35085
real 0m2.017s
user 0m0.113s
sys 0m1.942s
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Wilson Kok <wkok@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
switchdev_port_fwd_mark_set() is used to set the 'offload_fwd_mark' of
port netdevs so that packets being flooded by the device won't be
flooded twice.
It works by assigning a unique identifier (the ifindex of the first
bridge port) to bridge ports sharing the same parent ID. This prevents
packets from being flooded twice by the same switch, but will flood
packets through bridge ports belonging to a different switch.
This method is problematic when stacked devices are taken into account,
such as VLANs. In such cases, a physical port netdev can have upper
devices being members in two different bridges, thus requiring two
different 'offload_fwd_mark's to be configured on the port netdev, which
is impossible.
The main problem is that packet and netdev marking is performed at the
physical netdev level, whereas flooding occurs between bridge ports,
which are not necessarily port netdevs.
Instead, packet and netdev marking should really be done in the bridge
driver with the switch driver only telling it which packets it already
forwarded. The bridge driver will mark such packets using the mark
assigned to the ingress bridge port and will prevent the packet from
being forwarded through any bridge port sharing the same mark (i.e.
having the same parent ID).
Remove the current switchdev 'offload_fwd_mark' implementation and
instead implement the proposed method. In addition, make rocker - the
sole user of the mark - use the proposed method.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the ageing_time type in br_set_ageing_time() from u32 to what it
is expected to be, i.e. a clock_t.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch we had two flavors of most forwarding functions -
_forward and _deliver, the difference being that the latter are used
when the packets are locally originated. Instead of all this function
pointer passing and code duplication, we can just pass a boolean noting
that the packet was locally originated and use that to perform the
necessary checks in __br_forward. This gives a minor performance
improvement but more importantly consolidates the forwarding paths.
Also add a kernel doc comment to explain the exported br_forward()'s
arguments.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if the packet is going to be received locally we set skb0 or
sometimes called skb2 variables to the original skb. This can get
confusing and also we can avoid one conditional on the fast path by
simply using a boolean and passing it around. Thanks to Roopa for the
name suggestion.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As was suggested this patch adds support for the different versions of MLD
and IGMP query types. Since the user visible structure is still in net-next
we can augment it instead of adding netlink attributes.
The distinction between the different IGMP/MLD query types is done as
suggested in Section 7.1, RFC 3376 [1] and Section 8.1, RFC 3810 [2] based
on query payload size and code for IGMP. Since all IGMP packets go through
multicast_rcv() and it uses ip_mc_check_igmp/ipv6_mc_check_mld we can be
sure that at least the ip/ipv6 header can be directly used.
[1] https://tools.ietf.org/html/rfc3376#section-7
[2] https://tools.ietf.org/html/rfc3810#section-8.1
Suggested-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds stats support for the currently used IGMP/MLD types by the
bridge. The stats are per-port (plus one stat per-bridge) and per-direction
(RX/TX). The stats are exported via netlink via the new linkxstats API
(RTM_GETSTATS). In order to minimize the performance impact, a new option
is used to enable/disable the stats - multicast_stats_enabled, similar to
the recent vlan stats. Also in order to avoid multiple IGMP/MLD type
lookups and checks, we make use of the current "igmp" member of the bridge
private skb->cb region to record the type on Rx (both host-generated and
external packets pass by multicast_rcv()). We can do that since the igmp
member was used as a boolean and all the valid IGMP/MLD types are positive
values. The normal bridge fast-path is not affected at all, the only
affected paths are the flooding ones and since we make use of the IGMP/MLD
type, we can quickly determine if the packet should be counted using
cache-hot data (cb's igmp member). We add counters for:
* IGMP Queries
* IGMP Leaves
* IGMP v1/v2/v3 reports
* MLD Queries
* MLD Leaves
* MLD v1/v2 reports
These are invaluable when monitoring or debugging complex multicast setups
with bridges.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge is falsly dropping ipv6 mulitcast packets if there is:
1. No ipv6 address assigned on the brigde.
2. No external mld querier present.
3. The internal querier enabled.
When the bridge fails to build mld queries, because it has no
ipv6 address, it slilently returns, but keeps the local querier enabled.
This specific case causes confusing packet loss.
Ipv6 multicast snooping can only work if:
a) An external querier is present
OR
b) The bridge has an ipv6 address an is capable of sending own queries
Otherwise it has to forward/flood the ipv6 multicast traffic,
because snooping cannot work.
This patch fixes the issue by adding a flag to the bridge struct that
indicates that there is currently no ipv6 address assinged to the bridge
and returns a false state for the local querier in
__br_multicast_querier_exists().
Special thanks to Linus Lüssing.
Fixes: d1d81d4c3d ("bridge: check return value of ipv6_dev_get_saddr()")
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Acked-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new LINK_XSTATS_TYPE_BRIDGE attribute and implement the
RTM_GETSTATS callbacks for IFLA_STATS_LINK_XSTATS (fill_linkxstats and
get_linkxstats_size) in order to export the per-vlan stats.
The paddings were added because soon these fields will be needed for
per-port per-vlan stats (or something else if someone beats me to it) so
avoiding at least a few more netlink attributes.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for per-VLAN Tx/Rx statistics. Every global vlan context gets
allocated a per-cpu stats which is then set in each per-port vlan context
for quick access. The br_allowed_ingress() common function is used to
account for Rx packets and the br_handle_vlan() common function is used
to account for Tx packets. Stats accounting is performed only if the
bridge-wide vlan_stats_enabled option is set either via sysfs or netlink.
A struct hole between vlan_enabled and vlan_proto is used for the new
option so it is in the same cache line. Currently it is binary (on/off)
but it is intentionally restricted to exactly 0 and 1 since other values
will be used in the future for different purposes (e.g. per-port stats).
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race-condition when updating the mdb offload flag without using
the mulicast_lock. This reverts commit 9e8430f8d6 ("bridge: mdb:
Passing the port-group pointer to br_mdb module").
This patch marks offloaded MDB entry as "offload" by changing the port-
group flags and marks it as MDB_PG_FLAGS_OFFLOAD.
When switchdev PORT_MDB succeeded and adds a multicast group, a completion
callback is been invoked "br_mdb_complete". The completion function
locks the multicast_lock and finds the right net_bridge_port_group and
marks it as offloaded.
Fixes: 9e8430f8d6 ("bridge: mdb: Passing the port-group pointer to br_mdb module")
Reported-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the shared br_log_state function and print the info directly in
br_set_state, where the net_bridge_port state is actually changed.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Passing the port-group to br_mdb in order to allow direct access to the
structure. br_mdb will later use the structure to reflect HW reflection
status via "state" variable.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change net_bridge_port_group 'state' member to 'flags' and define new set
of flags internal to the kernel.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel reported a problem with switchdev devices because of the
order change of del_nbp operations, more specifically the move of
nbp_vlan_flush() which deletes all vlans and frees vlgrp after the
rx_handler has been unregistered. So in order to fix this move
vlan_flush back where it was and make it destroy the rhtable after
NULLing vlgrp and waiting a grace period to make sure noone can see it.
Reported-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge and port's vlgrp member is already used in RCU way, currently
we rely on the fact that it cannot disappear while the port exists but
that is error-prone and we might miss places with improper locking
(either RCU or RTNL must be held to walk the vlan_list). So make it
official and use RCU for vlgrp to catch offenders. Introduce proper vlgrp
accessors and use them consistently throughout the code.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use SWITCHDEV_F_SKIP_EOPNOTSUPP to skip over ports in bridge that don't
support setting ageing_time (or setting bridge attrs in general).
If push fails, don't update ageing_time in bridge and return err to user.
If push succeeds, update ageing_time in bridge and run gc_timer now to
recalabrate when to run gc_timer next, based on new ageing_time.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add IFLA_BR_VLAN_DEFAULT_PVID to allow setting/getting bridge's
default_pvid via netlink.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The checks that lead to num_vlans change are always what
br_vlan_should_use checks for, namely if the vlan is only a context or
not and depending on that it's either not counted or counted
as a real/used vlan respectively.
Also give better explanation in br_vlan_should_use's comment.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One obvious way to converge more code (which was also used by the
previous vlan code) is to move pvid inside net_bridge_vlan_group. This
allows us to simplify some and remove other port-specific functions.
Also gives us the ability to simply pass the vlan group and use all of the
contained information.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the bridge vlan implementation to use rhashtables
instead of bitmaps. The main motivation behind this change is that we
need extensible per-vlan structures (both per-port and global) so more
advanced features can be introduced and the vlan support can be
extended. I've tried to break this up but the moment net_port_vlans is
changed and the whole API goes away, thus this is a larger patch.
A few short goals of this patch are:
- Extensible per-vlan structs stored in rhashtables and a sorted list
- Keep user-visible behaviour (compressed vlans etc)
- Keep fastpath ingress/egress logic the same (optimizations to come
later)
Here's a brief list of some of the new features we'd like to introduce:
- per-vlan counters
- vlan ingress/egress mapping
- per-vlan igmp configuration
- vlan priorities
- avoid fdb entries replication (e.g. local fdb scaling issues)
The structure is kept single for both global and per-port entries so to
avoid code duplication where possible and also because we'll soon introduce
"port0 / aka bridge as port" which should simplify things further
(thanks to Vlad for the suggestion!).
Now we have per-vlan global rhashtable (bridge-wide) and per-vlan port
rhashtable, if an entry is added to a port it'll get a pointer to its
global context so it can be quickly accessed later. There's also a
sorted vlan list which is used for stable walks and some user-visible
behaviour such as the vlan ranges, also for error paths.
VLANs are stored in a "vlan group" which currently contains the
rhashtable, sorted vlan list and the number of "real" vlan entries.
A good side-effect of this change is that it resembles how hw keeps
per-vlan data.
One important note after this change is that if a VLAN is being looked up
in the bridge's rhashtable for filtering purposes (or to check if it's an
existing usable entry, not just a global context) then the new helper
br_vlan_should_use() needs to be used if the vlan is found. In case the
lookup is done only with a port's vlan group, then this check can be
skipped.
Things tested so far:
- basic vlan ingress/egress
- pvids
- untagged vlans
- undef CONFIG_BRIDGE_VLAN_FILTERING
- adding/deleting vlans in different scenarios (with/without global ctx,
while transmitting traffic, in ranges etc)
- loading/removing the module while having/adding/deleting vlans
- extracting bridge vlan information (user ABI), compressed requests
- adding/deleting fdbs on vlans
- bridge mac change, promisc mode
- default pvid change
- kmemleak ON during the whole time
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is immediately motivated by the bridge code that chains functions that
call into netfilter. Without passing net into the okfns the bridge code would
need to guess about the best expression for the network namespace to process
packets in.
As net is frequently one of the first things computed in continuation functions
after netfilter has done it's job passing in the desired network namespace is in
many cases a code simplification.
To support this change the function dst_output_okfn is introduced to
simplify passing dst_output as an okfn. For the moment dst_output_okfn
just silently drops the struct net.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While looking into fixing the local entries scalability issue I noticed
that the structure is badly arranged because vlan_id would fall in a
second cache line while keeping rcu which is used only when deleting
in the first, so re-arrange the structure and push rcu to the end so we
can get 16 bytes which can be used for other fields (by pushing rcu
fully in the second 64 byte chunk). With this change all the core
necessary information when doing fdb lookups will be available in a
single cache line.
pahole before (note vlan_id):
struct net_bridge_fdb_entry {
struct hlist_node hlist; /* 0 16 */
struct net_bridge_port * dst; /* 16 8 */
struct callback_head rcu; /* 24 16 */
long unsigned int updated; /* 40 8 */
long unsigned int used; /* 48 8 */
mac_addr addr; /* 56 6 */
unsigned char is_local:1; /* 62: 7 1 */
unsigned char is_static:1; /* 62: 6 1 */
unsigned char added_by_user:1; /* 62: 5 1 */
unsigned char added_by_external_learn:1; /* 62: 4 1 */
/* XXX 4 bits hole, try to pack */
/* XXX 1 byte hole, try to pack */
/* --- cacheline 1 boundary (64 bytes) --- */
__u16 vlan_id; /* 64 2 */
/* size: 72, cachelines: 2, members: 11 */
/* sum members: 65, holes: 1, sum holes: 1 */
/* bit holes: 1, sum bit holes: 4 bits */
/* padding: 6 */
/* last cacheline: 8 bytes */
}
pahole after (note vlan_id):
struct net_bridge_fdb_entry {
struct hlist_node hlist; /* 0 16 */
struct net_bridge_port * dst; /* 16 8 */
long unsigned int updated; /* 24 8 */
long unsigned int used; /* 32 8 */
mac_addr addr; /* 40 6 */
__u16 vlan_id; /* 46 2 */
unsigned char is_local:1; /* 48: 7 1 */
unsigned char is_static:1; /* 48: 6 1 */
unsigned char added_by_user:1; /* 48: 5 1 */
unsigned char added_by_external_learn:1; /* 48: 4 1 */
/* XXX 4 bits hole, try to pack */
/* XXX 7 bytes hole, try to pack */
struct callback_head rcu; /* 56 16 */
/* --- cacheline 1 boundary (64 bytes) was 8 bytes ago --- */
/* size: 72, cachelines: 2, members: 11 */
/* sum members: 65, holes: 1, sum holes: 7 */
/* bit holes: 1, sum bit holes: 4 bits */
/* last cacheline: 8 bytes */
}
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables bridge vlan_protocol to be configured through netlink.
When CONFIG_BRIDGE_VLAN_FILTERING is disabled, kernel behaves the
same way as this feature is not implemented.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the ability to toggle the vlan filtering support via
netlink. Since we're already running with rtnl in .changelink() we don't
need to take any additional locks.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send notifications on router port add and del/expire, re-use the already
existing MDBA_ROUTER and send NEWMDB/DELMDB netlink notifications
respectively.
Signed-off-by: Satish Ashok <sashok@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix:
net/bridge/br_if.c: In function 'br_dev_delete':
>> net/bridge/br_if.c:284:2: error: implicit declaration of function
>> 'br_multicast_dev_del' [-Werror=implicit-function-declaration]
br_multicast_dev_del(br);
^
cc1: some warnings being treated as errors
when igmp snooping is not defined.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the bridge (or port) is brought down/up flush only temp entries and
leave the perm ones. Flush perm entries only when deleting the bridge
device or the associated port.
Signed-off-by: Satish Ashok <sashok@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fill also the port group state when sending notifications.
Signed-off-by: Satish Ashok <sashok@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new argument to br_fdb_delete_by_port which allows to specify a
vid to match when flushing entries and use it in nbp_vlan_delete() to
flush the dynamically learned entries of the vlan/port pair when removing
a vlan from a port. Before this patch only the local mac was being
removed and the dynamically learned ones were left to expire.
Note that the do_all argument is still respected and if specified, the
vid will be ignored.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 fragmented packets are not forwarded on an ethernet bridge
with netfilter ip6_tables loaded. e.g. steps to reproduce
1) create a simple bridge like this
modprobe br_netfilter
brctl addbr br0
brctl addif br0 eth0
brctl addif br0 eth2
ifconfig eth0 up
ifconfig eth2 up
ifconfig br0 up
2) place a host with an IPv6 address on each side of the bridge
set IPv6 address on host A:
ip -6 addr add fd01:2345:6789:1::1/64 dev eth0
set IPv6 address on host B:
ip -6 addr add fd01:2345:6789:1::2/64 dev eth0
3) run a simple ping command on host A with packets > MTU
ping6 -s 4000 fd01:2345:6789:1::2
4) wait some time and run e.g. "ip6tables -t nat -nvL" on the bridge
IPv6 fragmented packets traverse the bridge cleanly until somebody runs.
"ip6tables -t nat -nvL". As soon as it is run (and netfilter modules are
loaded) IPv6 fragmented packets do not traverse the bridge any more (you
see no more responses in ping's output).
After applying this patch IPv6 fragmented packets traverse the bridge
cleanly in above scenario.
Signed-off-by: Bernhard Thaler <bernhard.thaler@wvnet.at>
[pablo@netfilter.org: small changes to br_nf_dev_queue_xmit]
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently frag_max_size is member of br_input_skb_cb and copied back and
forth using IPCB(skb) and BR_INPUT_SKB_CB(skb) each time it is changed or
used.
Attach frag_max_size to nf_bridge_info and set value in pre_routing and
forward functions. Use its value in forward and xmit functions.
Signed-off-by: Bernhard Thaler <bernhard.thaler@wvnet.at>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
BR_GROUPFWD_RESTRICTED bitmask restricts users from setting values to
/sys/class/net/brX/bridge/group_fwd_mask that allow forwarding of
some IEEE 802.1D Table 7-10 Reserved addresses:
(MAC Control) 802.3 01-80-C2-00-00-01
(Link Aggregation) 802.3 01-80-C2-00-00-02
802.1AB LLDP 01-80-C2-00-00-0E
Change BR_GROUPFWD_RESTRICTED to allow to forward LLDP frames and document
group_fwd_mask.
e.g.
echo 16384 > /sys/class/net/brX/bridge/group_fwd_mask
allows to forward LLDP frames.
This may be needed for bridge setups used for network troubleshooting or
any other scenario where forwarding of LLDP frames is desired (e.g. bridge
connecting a virtual machine to real switch transmitting LLDP frames that
virtual machine needs to receive).
Tested on a simple bridge setup with two interfaces and host transmitting
LLDP frames on one side of this bridge (used lldpd). Setting group_fwd_mask
as described above lets LLDP frames traverse bridge.
Signed-off-by: Bernhard Thaler <bernhard.thaler@wvnet.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
NLM_F_MULTI must be used only when a NLMSG_DONE message is sent. In fact,
it is sent only at the end of a dump.
Libraries like libnl will wait forever for NLMSG_DONE.
Fixes: e5a55a8987 ("net: create generic bridge ops")
Fixes: 815cccbf10 ("ixgbe: add setlink, getlink support to ixgbe and ixgbevf")
CC: John Fastabend <john.r.fastabend@intel.com>
CC: Sathya Perla <sathya.perla@emulex.com>
CC: Subbu Seetharaman <subbu.seetharaman@emulex.com>
CC: Ajit Khaparde <ajit.khaparde@emulex.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: intel-wired-lan@lists.osuosl.org
CC: Jiri Pirko <jiri@resnulli.us>
CC: Scott Feldman <sfeldma@gmail.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
CC: bridge@lists.linux-foundation.org
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the output paths in particular, we have to sometimes deal with two
socket contexts. First, and usually skb->sk, is the local socket that
generated the frame.
And second, is potentially the socket used to control a tunneling
socket, such as one the encapsulates using UDP.
We do not want to disassociate skb->sk when encapsulating in order
to fix this, because that would break socket memory accounting.
The most extreme case where this can cause huge problems is an
AF_PACKET socket transmitting over a vxlan device. We hit code
paths doing checks that assume they are dealing with an ipv4
socket, but are actually operating upon the AF_PACKET one.
Signed-off-by: David S. Miller <davem@davemloft.net>
e5de75b ("netfilter: bridge: move DNAT helper to br_netfilter") results
in the following link problem:
net/bridge/br_device.c:29: undefined reference to `br_nf_prerouting_finish_bridge`
Moreover it creates a hard dependency between br_netfilter and the
bridge core, which is what we've been trying to avoid so far.
Resolve this problem by using a hook structure so we reduce #ifdef
pollution and keep bridge netfilter specific code under br_netfilter.c
which was the original intention.
Reported-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree. Basically, improvements for the packet rejection infrastructure,
deprecation of CLUSTERIP, cleanups for nf_tables and some untangling for
br_netfilter. More specifically they are:
1) Send packet to reset flow if checksum is valid, from Florian Westphal.
2) Fix nf_tables reject bridge from the input chain, also from Florian.
3) Deprecate the CLUSTERIP target, the cluster match supersedes it in
functionality and it's known to have problems.
4) A couple of cleanups for nf_tables rule tracing infrastructure, from
Patrick McHardy.
5) Another cleanup to place transaction declarations at the bottom of
nf_tables.h, also from Patrick.
6) Consolidate Kconfig dependencies wrt. NF_TABLES.
7) Limit table names to 32 bytes in nf_tables.
8) mac header copying in bridge netfilter is already required when
calling ip_fragment(), from Florian Westphal.
9) move nf_bridge_update_protocol() to br_netfilter.c, also from
Florian.
10) Small refactor in br_netfilter in the transmission path, again from
Florian.
11) Move br_nf_pre_routing_finish_bridge_slow() to br_netfilter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Only one caller, there is no need to keep this in a header.
Move it to br_netfilter.c where this belongs to.
Based on patch from Florian Westphal.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This extends the design in commit 958501163d ("bridge: Add support for
IEEE 802.11 Proxy ARP") with optional set of rules that are needed to
meet the IEEE 802.11 and Hotspot 2.0 requirements for ProxyARP. The
previously added BR_PROXYARP behavior is left as-is and a new
BR_PROXYARP_WIFI alternative is added so that this behavior can be
configured from user space when required.
In addition, this enables proxyarp functionality for unicast ARP
requests for both BR_PROXYARP and BR_PROXYARP_WIFI since it is possible
to use unicast as well as broadcast for these frames.
The key differences in functionality:
BR_PROXYARP:
- uses the flag on the bridge port on which the request frame was
received to determine whether to reply
- block bridge port flooding completely on ports that enable proxy ARP
BR_PROXYARP_WIFI:
- uses the flag on the bridge port to which the target device of the
request belongs
- block bridge port flooding selectively based on whether the proxyarp
functionality replied
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
bridge flags are needed inside ndo_bridge_setlink/dellink handlers to
avoid another call to parse IFLA_AF_SPEC inside these handlers
This is used later in this series
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch benefits from newly introduced switchdev notifier and uses it
to propagate fdb learn events from rocker driver to bridge. That avoids
direct function calls and possible use by other listeners (ovs).
Suggested-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
When the swdev device learns a new mac/vlan on a port, it sends some async
notification to the driver and the driver installs an FDB in the device.
To give a holistic system view, the learned mac/vlan should be reflected
in the bridge's FBD table, so the user, using normal iproute2 cmds, can view
what is currently learned by the device. This API on the bridge driver gives
a way for the swdev driver to install an FBD entry in the bridge FBD table.
(And remove one).
This is equivalent to the device running these cmds:
bridge fdb [add|del] <mac> dev <dev> vid <vlan id> master
This patch needs some extra eyeballs for review, in paricular around the
locking and contexts.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do the work of parsing NDA_VLAN directly in rtnetlink code, pass simple
u16 vid to drivers from there.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This feature is defined in IEEE Std 802.11-2012, 10.23.13. It allows
the AP devices to keep track of the hardware-address-to-IP-address
mapping of the mobile devices within the WLAN network.
The AP will learn this mapping via observing DHCP, ARP, and NS/NA
frames. When a request for such information is made (i.e. ARP request,
Neighbor Solicitation), the AP will respond on behalf of the
associated mobile device. In the process of doing so, the AP will drop
the multicast request frame that was intended to go out to the wireless
medium.
It was recommended at the LKS workshop to do this implementation in
the bridge layer. vxlan.c is already doing something very similar.
The DHCP snooping code will be added to the userspace application
(hostapd) per the recommendation.
This RFC commit is only for IPv4. A similar approach in the bridge
layer will be taken for IPv6 as well.
Signed-off-by: Kyeyoon Park <kyeyoonp@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we may defragment the packet in IPv4 PRE_ROUTING and refragment
it after POST_ROUTING we should save the value of frag_max_size.
This is still very wrong as the bridge is supposed to leave the
packets intact, meaning that the right thing to do is to use the
original frag_list for fragmentation.
Unfortunately we don't currently guarantee that the frag_list is
left untouched throughout netfilter so until this changes this is
the best we can do.
There is also a spot in FORWARD where it appears that we can
forward a packet without going through fragmentation, mark it
so that we can fix it later.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when vlan filtering is turned on on the bridge, the bridge
will drop all traffic untill the user configures the filter. This
isn't very nice for ports that don't care about vlans and just
want untagged traffic.
A concept of a default_pvid was recently introduced. This patch
adds filtering support for default_pvid. Now, ports that don't
care about vlans and don't define there own filter will belong
to the VLAN of the default_pvid and continue to receive untagged
traffic.
This filtering can be disabled by setting default_pvid to 0.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if the pvid is not set, we return an illegal vlan value
even though the pvid value is set to 0. Since pvid of 0 is currently
invalid, just return 0 instead. This makes the current and future
checks simpler.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows the user to set and retrieve default_pvid
value. A new value can only be stored when vlan filtering
is disabled.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for being able to propagate port states to e.g: notifiers
or other kernel parts, do not manipulate the port state directly, but
instead use a helper function which will allow us to do a bit more than
just setting the state.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
pull request: netfilter/ipvs updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next,
most relevantly they are:
1) Four patches to make the new nf_tables masquerading support
independent of the x_tables infrastructure. This also resolves a
compilation breakage if the masquerade target is disabled but the
nf_tables masq expression is enabled.
2) ipset updates via Jozsef Kadlecsik. This includes the addition of the
skbinfo extension that allows you to store packet metainformation in the
elements. This can be used to fetch and restore this to the packets through
the iptables SET target, patches from Anton Danilov.
3) Add the hash:mac set type to ipset, from Jozsef Kadlecsick.
4) Add simple weighted fail-over scheduler via Simon Horman. This provides
a fail-over IPVS scheduler (unlike existing load balancing schedulers).
Connections are directed to the appropriate server based solely on
highest weight value and server availability, patch from Kenny Mathis.
5) Support IPv6 real servers in IPv4 virtual-services and vice versa.
Simon Horman informs that the motivation for this is to allow more
flexibility in the choice of IP version offered by both virtual-servers
and real-servers as they no longer need to match: An IPv4 connection
from an end-user may be forwarded to a real-server using IPv6 and
vice versa. No ip_vs_sync support yet though. Patches from Alex Gartrell
and Julian Anastasov.
6) Add global generation ID to the nf_tables ruleset. When dumping from
several different object lists, we need a way to identify that an update
has ocurred so userspace knows that it needs to refresh its lists. This
also includes a new command to obtain the 32-bits generation ID. The
less significant 16-bits of this ID is also exposed through res_id field
in the nfnetlink header to quickly detect the interference and retry when
there is no risk of ID wraparound.
7) Move br_netfilter out of the bridge core. The br_netfilter code is
built in the bridge core by default. This causes problems of different
kind to people that don't want this: Jesper reported performance drop due
to the inconditional hook registration and I remember to have read complains
on netdev from people regarding the unexpected behaviour of our bridging
stack when br_netfilter is enabled (fragmentation handling, layer 3 and
upper inspection). People that still need this should easily undo the
damage by modprobing the new br_netfilter module.
8) Dump the set policy nf_tables that allows set parameterization. So
userspace can keep user-defined preferences when saving the ruleset.
From Arturo Borrero.
9) Use __seq_open_private() helper function to reduce boiler plate code
in x_tables, From Rob Jones.
10) Safer default behaviour in case that you forget to load the protocol
tracker. Daniel Borkmann and Florian Westphal detected that if your
ruleset is stateful, you allow traffic to at least one single SCTP port
and the SCTP protocol tracker is not loaded, then any SCTP traffic may
be pass through unfiltered. After this patch, the connection tracking
classifies SCTP/DCCP/UDPlite/GRE packets as invalid if your kernel has
been compiled with support for these modules.
====================
Trivially resolved conflict in include/linux/skbuff.h, Eric moved some
netfilter skbuff members around, and the netfilter tree adjusted the
ifdef guards for the bridging info pointer.
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper reported that br_netfilter always registers the hooks since
this is part of the bridge core. This harms performance for people that
don't need this.
This patch modularizes br_netfilter so it can be rmmod'ed, thus,
the hooks can be unregistered. I think the bridge netfilter should have
been a separated module since the beginning, Patrick agreed on that.
Note that this is breaking compatibility for users that expect that
bridge netfilter is going to be available after explicitly 'modprobe
bridge' or via automatic load through brctl.
However, the damage can be easily undone by modprobing br_netfilter.
The bridge core also spots a message to provide a clue to people that
didn't notice that this has been deprecated.
On top of that, the plan is that nftables will not rely on this software
layer, but integrate the connection tracking into the bridge layer to
enable stateful filtering and NAT, which is was bridge netfilter users
seem to require.
This patch still keeps the fake_dst_ops in the bridge core, since this
is required by when the bridge port is initialized. So we can safely
modprobe/rmmod br_netfilter anytime.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Florian Westphal <fw@strlen.de>
The bridge code checks if vlan filtering is enabled on both
ingress and egress. When the state flip happens, it
is possible for the bridge to currently be forwarding packets
and forwarding behavior becomes non-deterministic. Bridge
may drop packets on some interfaces, but not others.
This patch solves this by caching the filtered state of the
packet into skb_cb on ingress. The skb_cb is guaranteed to
not be over-written between the time packet entres bridge
forwarding path and the time it leaves it. On egress, we
can then check the cached state to see if we need to
apply filtering information.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dumping a bridge fdb dumps every fdb entry
held. With this change we are going to filter
on selected bridge port.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables us to change the vlan protocol for vlan filtering.
We come to be able to filter frames on the basis of 802.1ad vlan tags
through a bridge.
This also changes br->group_addr if it has not been set by user.
This is needed for an 802.1ad bridge.
(See IEEE 802.1Q-2011 8.13.5.)
Furthermore, this sets br->group_fwd_mask_required so that an 802.1ad
bridge can forward the Nearest Customer Bridge group addresses except
for br->group_addr, which should be passed to higher layer.
To change the vlan protocol, write a protocol in sysfs:
# echo 0x88a8 > /sys/class/net/br0/bridge/vlan_protocol
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a bridge is an 802.1ad bridge, it must forward another bridge group
addresses (the Nearest Customer Bridge group addresses).
(For details, see IEEE 802.1Q-2011 8.6.3.)
As user might not want group_fwd_mask to be modified by enabling 802.1ad,
introduce a new mask, group_fwd_mask_required, which indicates addresses
the bridge wants to forward. This will be set by enabling 802.1ad.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables a bridge to have vlan protocol informantion and allows vlan
tag manipulation (retrieve, insert and remove tags) according to the vlan
protocol.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding bridge support to the batman-adv multicast optimization requires
batman-adv knowing about the existence of bridged-in IGMP/MLD queriers
to be able to reliably serve any multicast listener behind this same
bridge.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this new, exported function br_multicast_list_adjacent(net_dev) a
list of IPv4/6 addresses is returned. This list contains all multicast
addresses sensed by the bridge multicast snooping feature on all bridge
ports of the bridge interface of net_dev, excluding addresses from the
specified net_device itself.
Adding bridge support to the batman-adv multicast optimization requires
batman-adv knowing about the existence of bridged-in multicast
listeners to be able to reliably serve them with multicast packets.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
MLDv1 (RFC2710 section 6), MLDv2 (RFC3810 section 7.6.2), IGMPv2
(RFC2236 section 3) and IGMPv3 (RFC3376 section 6.6.2) specify that the
querier with lowest source address shall become the selected
querier.
So far the bridge stopped its querier as soon as it heard another
querier regardless of its source address. This results in the "wrong"
querier potentially becoming the active querier or a potential,
unnecessary querying delay.
With this patch the bridge memorizes the source address of the currently
selected querier and ignores queries from queriers with a higher source
address than the currently selected one. This slight optimization is
supposed to make it more RFC compliant (but is rather uncritical and
therefore probably not necessary to be queued for stable kernels).
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov