The tps6524x driver uses spi_dev_get() to take a copy of the SPI device
it uses but has no obvious reason to do so and never calls spi_dev_put()
to release the reference. Fix this to just a straight copy.
Signed-off-by: Mark Brown <broonie@kernel.org>
IC type options 00, 13 and 23 are sharing the same DIE_ID 0.
Let's differentiate between these revisions.
FAN53555UC13X has the ID 0 and REV 0xf, starts at 800mV and
increments in 10mV steps.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
FAN53555BUC18X has the DIE_ID 8, starts at 600mV and
increments in 10mV steps.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
suspend_prepare can be called during regulator init time also, where
the mutex is not locked yet. This causes a false lockdep warning.
To avoid the problem, remove the lockdep assertion from the function
causing the issue. An alternative would be to lock the mutex during
init, but this would cause other problems (some APIs used during init
will attempt to lock the mutex also, causing deadlock.)
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the driver for the Powerventure PV88080 BUCKs regulator.
It communicates via an I2C bus to the device.
Signed-off-by: James Ban <James.Ban..opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver did not provide default value for ramp delay for LDOs which lead
to warning in dmesg, e.g. on Odroid XU4:
[ 1.486076] vdd_ldo9: ramp_delay not set
[ 1.506875] vddq_mmc2: ramp_delay not set
[ 1.523766] vdd_ldo15: ramp_delay not set
[ 1.544702] vdd_sd: ramp_delay not set
The datasheet for all the S2MPS1x family is inconsistent here and does
not specify unambiguously the value of ramp delay for LDO. It mentions
30 mV/us in one timing diagram but then omits it completely in LDO
regulator characteristics table (it is specified for bucks).
However the vendor kernels for Galaxy S5 and Odroid XU3 use values of 12
mV/us or 24 mV/us.
Without the ramp delay value the consumers do not wait for voltage
settle after changing it. Although the proper value of ramp delay for
LDOs is unknown, it seems safer to use at least some value from
reference kernel than to leave it unset.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
I had a thinko in spmi_regulator_select_voltage_same_range() when
converting it to return selectors via the function's return value
instead of by modifying a pointer argument. I only tested
multi-range regulators so this passed through testing. Fix it by
returning the selector here.
Fixes: 1b5b196892 ("regulator: qcom_spmi: Only use selector based regulator ops")
Reported-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is harmless but my static checker complains that "tmp" is
uninitialized if lp3972_i2c_read() fails. I have moved the line of code
below the error handling to silence the warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is harmless but if lp3971_i2c_read() fails then "tmp" can be
uninitialized. Silence the warning by moving the error handling up a
line.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver MAX8973 supports the driver for Maxim PMIC MAX77621.
MAX77621 supports the junction temp warning at 120 degC and
140 degC which is configurable. It generates alert signal when
junction temperature crosses these threshold.
MAX77621 does not support the continuous temp monitoring of
junction temperature. It just report whether junction temperature
crossed the threshold or not.
Add support to
- Configure junction temp warning threshold via DT property
to generate alert when it crosses the threshold.
- Add support to interrupt the host from this device when alert
occurred.
- read the junction temp via thermal framework.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When we acquire a shareable enable GPIO on probe we do so with the
regulator_list_mutex held. However when we release the GPIOs we do this
immediately after dropping the mutex meaning that the list could become
corrupted. Move the release into the locked region to avoid this.
Signed-off-by: Mark Brown <broonie@kernel.org>
device_register() is calling ->get_voltage() as part of it's sysfs attribute
initialization process, and this functions might need to know the regulator
constraints to return a valid value.
This is at least true for the pwm regulator driver (when operating in
continuous mode) which needs to know the minimum and maximum voltage values
to calculate the current voltage:
min_uV + (((max_uV - min_uV) * dutycycle) / 100);
Move device_register() after set_machine_constraints() to make sure those
constraints are correctly initialized when ->get_voltage() is called.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Stephen Barber <smbarber@chromium.org>
Tested-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When a regulator is in bypass mode it is functioning as a switch
returning the voltage set in the regulator will not give the voltage
being output by the regulator as it's just passing through its supply.
This means that when we are getting the voltage from a regulator we
should check to see if it is in bypass mode and if it is we should
report the voltage from the supply rather than that which is set on the
regulator.
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
[treding@nvidia.com: return early for bypass mode]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A const pointer to regulator ops is stored in regulator descriptors. The
operations never need to be modified, so define them as const as a hint
to the compiler that they can go into .rodata.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
LD06 on the AS3722 power management IC supports a bypass mode. Bypass
is enabled for the LDO by writing the value 0x3F to the voltage select
field in the control register for the LDO. Note that this is the same
register and field that is used to select the voltage as well for the
LDO.
Add support for bypass on LDO6 by specifying the various bypass
parameters for regulator and adding new function pointer tables for the
LDO. Note that the bypass OFF value is the same as the ON value simply
because there is no actual OFF value and bypass will be disabled when
a new voltage is written to the VSEL field.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver's init and exit function don't do anything besides registering
and unregistering the platform driver, so the module_platform_driver()
macro could just be used instead of having separate functions.
Currently the macro is not being used because the driver is initialized at
subsys init call level but this isn't necessary since consumer devices are
defined in the DT as dependencies so there's no need for init calls order.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver's init and exit function don't do anything besides registering
and unregistering the platform driver, so the module_platform_driver()
macro could just be used instead of having separate functions.
Currently the macro is not being used because the driver is initialized at
subsys init call level but this isn't necessary since consumer devices are
defined in the DT as dependencies so there's no need for init calls order.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit <2330b05c095bdeaaf1261c54cd2d4b9127496996> ("regulator: twl: Make
sure we have access to powerbus before trying to write to it")
has implemented the needed logic to correctly access powerbus through i2c,
however it brought a typo when powerbus configuration is restored, which
results in writing to a wrong register. Fix that by providing the correct
register value.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In continuous mode of the PWM regulators, the requested voltage
PWM duty cycle is calculated in terms of 100% scale where entire
range denotes 100%. The calculation for PWM pulse ON time(duty_pulse)
is done as:
duty_cycle = ((requested - minimum) * 100) / voltage_range.
then duty pulse is calculated as
duty_pulse = (pwm_period/100) * duty_cycle
This leads to the calculation error if we have the requested voltage
where accurate pulse time is possible.
For example: Consider following case
voltage range is 800000uV to 1350000uV.
pwm-period = 1550ns (1ns time is 1mV).
Requested 900000uV.
duty_cycle = ((900000uV - 800000uV) * 100)/ 1550000
= 6.45 but we will get 6.
duty_pulse = (1550/100) * 6 = 90 pulse time.
90 pulse time is equivalent to 90mV and this gives us pulse time equivalent
to 890000uV instead of 900000uV.
Proposing the solution in which if requested voltage makes the accurate
duty pulse then there will not be any error. On this case, if
(req_uV - min_uV) * pwm_period is perfect dividable by voltage_range
then get the duty pulse time directly.
duty_pulse = ((900000uV - 800000uV) * 1550)/1550000)
= 100
and this is equivalent to 100mV and so final voltage is
(800000 + 100000) = 900000uV which is same as requested,
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct smasung.com into samsung.com.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_map_mode is needed so to be possible to set initial regulators mode from
the board DTS. Otherwise, for DT boot, regulators are left in their default
state after reset/reboot. Document device specific modes as well.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mixing raw voltage and selector based regulator ops is
inconsistent. This driver already supports some selector based
ops via the list_voltage and set_voltage_time_sel ops but it uses
raw voltage ops for get_voltage and set_voltage. This causes
problems for regulator_set_voltage() and automatic insertion of
slewing delays because set_voltage_time_sel() is only used if the
regulator ops are all selector based. Put another way, delays
aren't happening at all right now when we should be waiting for
voltages to settle. Let's move to pure selector based regulator
ops so that the delays are inserted properly.
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Only the FT SMPS type regulators have slewing supported in the
driver, but all types of SMPS regulators need the same support.
The only difference is that some SMPS regulators don't have a
step size and the step delay is typically 20, not 8. Luckily, the
step size reads as 0 for the non-FT types, so we can always read
that, but we need to detect which type of regulator we're using
to figure out what step delay to use. Make these minor
adjustments to the slew rate calculations and add support for the
delay function to the appropriate regulator ops.
Reported-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 5e3ca2b349 ("regulator: Try to resolve regulators supplies on
registration") added a call to regulator_resolve_supply() within
regulator_register() where the regulator_list_mutex is held. This causes
a deadlock to occur on the Tegra114 Dalmore board when the palmas PMIC
is registered because regulator_register_resolve_supply() calls
regulator_dev_lookup() which may try to acquire the regulator_list_mutex
again.
Fix this by releasing the mutex before calling
regulator_register_resolve_supply() and update the error exit path to
ensure the mutex is released on an error.
[Made commit message more legible -- broonie]
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Flagging voltage changes as possible for exactly specified voltages
appears to be triggering bugs in the SDHCI code (it should be able to
handle the case where only one voltage it wants is in the range it is
allowed to set) so make sure we only set the flag in cases where there's
genuine variability.
Signed-off-by: Mark Brown <broonie@kernel.org>
This aids in debugging problems triggered by the regulator core applying
its constraints, we could potentially crash immediately after updating
the voltage if the constraints are buggy.
Signed-off-by: Mark Brown <broonie@kernel.org>
This can be used to expose the act8600 registers via debugfs.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This makes the code easier to read and it avoids a dynamic memory
allocation.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Most Maxim PMIC regulator drivers are for sub-devices of Multi-Function
Devices with drivers under drivers/mfd. But for many of these, the same
object file name was used for both the MFD and the regulator drivers.
Having 2 different drivers with the same name causes a lot of confusion
to Kbuild, specially if these are built as module since only one module
will be installed and also exported symbols will be undefined due being
overwritten by the other module during modpost.
For example, it fixes the following issue when both drivers are module:
$ make M=drivers/regulator/
...
CC [M] drivers/regulator//max14577.o
Building modules, stage 2.
MODPOST 1 modules
WARNING: "maxim_charger_calc_reg_current" [drivers/regulator//max14577.ko] undefined!
WARNING: "maxim_charger_currents" [drivers/regulator//max14577.ko] undefined!
Reported-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 6261b06de5 ("regulator: Defer lookup of supply to regulator_get")
moved the regulator supplies lookup logic from the regulators registration
to the regulators get time.
Unfortunately, that changed the behavior of the regulator core since now a
parent supply with a child regulator marked as always-on, won't be enabled
unless a client driver attempts to get the child regulator during boot.
This patch tries to resolve the parent supply for the already registered
regulators each time that a new regulator is registered. So the regulators
that have child regulators marked as always on will be enabled regardless
if a driver gets the child regulator or not.
That was the behavior before the mentioned commit, since parent supplies
were looked up at regulator registration time instead of during child get.
Since regulator_resolve_supply() checks for rdev->supply, most of the times
it will be a no-op. Errors aren't checked to keep the possible out of order
dependencies which was the motivation for the mentioned commit.
Also, the supply being available will be enforced on regulator get anyways
in case the resolve fails on regulators registration.
Fixes: 6261b06de5 ("regulator: Defer lookup of supply to regulator_get")
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org> # 4.1+
On some designs, a handful of the regulators can't be read via
SPMI transactions because they're "secure" and not intended to be
touched by non-secure processors. This driver unconditionally
attempts to read the id registers of all the regulators though,
leading to probe failing and no regulators being registered.
Let's ignore any errors from failing to read the registers and
keep adding other regulators so that this driver can probe on
such devices.
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Document the regulators available on pm8994 and add support for
this PMIC to the SPMI PMIC regulator driver.
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When machine constraints are applied, regulator framework first sets
initial mode (if any) and then enables the regulator if needed. The current
code in twl4030reg_set_mode always checks if the regulator is enabled
before applying the mode. That results in -EACCES error returned for
"always-on" regulators which have "initial-mode" set in the board DTS. Fix
that by removing the unneeded check.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the TRM, we need to enable i2c access to powerbus before
writing to it. Also, a new write to powerbus should not be attempted if
there is a pending transfer. The current code does not implement that
functionality and while there are no known problems caused by that, it is
better to follow what TRM says.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The buck9 regulator of S2MPS11 PMIC had incorrect vsel_mask (0xff
instead of 0x1f) thus reading entire register as buck9's voltage. This
effectively caused regulator core to interpret values as higher voltages
than they were and then to set real voltage much lower than intended.
The buck9 provides power to other regulators, including LDO13
and LDO19 which supply the MMC2 (SD card). On Odroid XU3/XU4 the lower
voltage caused SD card detection errors on Odroid XU3/XU4:
mmc1: card never left busy state
mmc1: error -110 whilst initialising SD card
During driver probe the regulator core was checking whether initial
voltage matches the constraints. With incorrect vsel_mask of 0xff and
default value of 0x50, the core interpreted this as 5 V which is outside
of constraints (3-3.775 V). Then the regulator core was adjusting the
voltage to match the constraints. With incorrect vsel_mask this new
voltage mapped to a vere low voltage in the driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
Currently we only attempt to set the voltage during constraints
application if an exact voltage is specified. Extend this so that if
the currently set voltage for the regulator is outside the bounds set in
constraints we will move the voltage to the nearest constraint, raising
to the minimum or lowering to the maximum as needed. This ensures that
drivers can probe without the hardware being driven out of spec.
Reported-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Apparently due to a wrongly resolved merge conflict between two
branches, which contained the same commit, the commit contents
partially was added two times in a row.
This change reverts the latter wrong inclusion of commit 909f7ee0b5
("regulator: core: Add support for active-discharge configuration").
The first applied commit 670666b9e0 ("regulator: core: Add support
for active-discharge configuration") is not touched.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow the core to always use the voltage constraints to set the voltage
on startup. A forthcoming change in that code will ensure that we bring
out of constraints voltages into spec with this setting.
Signed-off-by: Mark Brown <broonie@kernel.org>
The check would dereference pdata, which can be NULL in the non-DT
use case.
Nothing will break if pdata->num_regulators is larger than the number
of regulators that the driver defines: pdata->num_regulators is only
read in act8865_get_init_data() to iterate through pdata->regulators.
The error handler might have some value as a sanity check on the
platform data, but the platform data could be broken in many other
ways that are not checked for (unknown IDs, duplicate IDs), so I see
no reason to perform only this specific check.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The local variable "dev" already contains a pointer to the device,
so there is no need to take the address of "client->dev" again.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulator_resolve_supply() function checks if a supply has been
associated with a regulator to avoid enabling it if that is not the
case.
But the supply was already looked up with regulator_resolve_supply()
and set with set_supply() before the check and both return on error.
So the fact that this statement has been reached means that neither
of them failed and a supply must be associated with the regulator.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Freescale Touch Screen ADC
- X-Powers AXP PMIC with RSB
- TI TPS65086 Power Management IC (PMIC)
- New Device Support
- Supply device PCI IDs for Intel Broxton
- Fix-ups
- Move to clkdev_create() API; intel_quark_i2c_gpio
- Complete re-write of TI's TPS65912 Power Management IC (PMIC)
- Remove unnecessary function argument; axp20x
- Separate out bus related code; axp20x
- Coding Style changes; axp20x
- Allow more drivers to be compiled as modules
- Work around false positive 'used uninitialised' warning; db8500-prcmu
- Bug Fixes
- Remove do_div(); fsl-imx25-gcq
- Fix driver init when built-in; tps65010
- Fix clock-unregister leak; intel-lpss
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gTBA
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Freescale Touch Screen ADC
- X-Powers AXP PMIC with RSB
- TI TPS65086 Power Management IC (PMIC)
New Device Support:
- Supply device PCI IDs for Intel Broxton
Fix-ups:
- Move to clkdev_create() API; intel_quark_i2c_gpio
- Complete re-write of TI's TPS65912 Power Management IC (PMIC)
- Remove unnecessary function argument; axp20x
- Separate out bus related code; axp20x
- Coding Style changes; axp20x
- Allow more drivers to be compiled as modules
- Work around false positive 'used uninitialised' warning; db8500-prcmu
Bug Fixes:
- Remove do_div(); fsl-imx25-gcq
- Fix driver init when built-in; tps65010
- Fix clock-unregister leak; intel-lpss"
* tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (53 commits)
mfd: intel-lpss: Pass I2C configuration via properties on BXT
mfd: imx6sx: Add PCIe register definitions for iomuxc gpr
mfd: ipaq-micro: Use __maybe_unused to hide pm functions
mfd: max77686: Add max77802 to I2C device ID table
mfd: max77686: Export OF module alias information
mfd: max77686: Allow driver to be built as a module
mfd: stmpe: Add the proper PWM resources
mfd: tps65090: Set regmap config reg counts properly
mfd: syscon: Return ENOTSUPP instead of ENOSYS when disabled
mfd: as3711: Set regmap config reg counts properly
mfd: rc5t583: Set regmap config reg counts properly
gpio: tps65086: Add GPO driver for the TPS65086 PMIC
mfd: mt6397: Add platform device ID table
mfd: da9063: Fix missing volatile registers in the core regmap_range volatile lists
mfd: mt6397: Add MT6323 support to MT6397 driver
mfd: mt6397: Add support for different Slave types
mfd: mt6397: int_con and int_status may vary in location
dt-bindings: mfd: Add bindings for the MediaTek MT6323 PMIC
mfd: da9062: Fix missing volatile registers in the core regmap_range volatile lists
mfd: Add documentation for ACT8945A DT bindings
...
Core changes:
- The gpio_chip is now a *real device*. Until now the gpio chips
were just piggybacking the parent device or (gasp) floating in
space outside of the device model. We now finally make GPIO chips
devices. The gpio_chip will create a gpio_device which contains
a struct device, and this gpio_device struct is kept private.
Anything that needs to be kept private from the rest of the kernel
will gradually be moved over to the gpio_device.
- As a result of making the gpio_device a real device, we have added
resource management, so devm_gpiochip_add_data() will cut down on
overhead and reduce code lines. A huge slew of patches convert
almost all drivers in the subsystem to use this.
- Building on making the GPIO a real device, we add the first step
of a new userspace ABI: the GPIO character device. We take small
steps here, so we first add a pure *information* ABI and the tool
"lsgpio" that will list all GPIO devices on the system and all
lines on these devices. We can now discover GPIOs properly from
userspace. We still have not come up with a way to actually *use*
GPIOs from userspace.
- To encourage people to use the character device for the future,
we have it always-enabled when using GPIO. The old sysfs ABI is
still opt-in (and can be used in parallel), but is marked as
deprecated. We will keep it around for the foreseeable future,
but it will not be extended to cover ever more use cases.
Cleanup:
- Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
includes. This dates back to when GPIO was an opt-in feature and
no shared library even existed: just a header file with proper
prototypes was provided and all semantics were up to the arch to
implement. These patches make the GPIO chip even more a proper
device and cleans out leftovers of the old in-kernel API here
and there. Still some cruft is left but it's very little now.
- There is still some clamping of return values for .get() going
on, but we now return sane values in the vast majority of drivers
and the errorpath is sanitized. Some patches for powerpc, blackfin
and unicore still drop in.
- We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
implementations to use gpiochip_add_data() and cut down on code
lines.
- MPC8xxx is converted to use the generic GPIO helpers.
- ATH79 is converted to use the generic GPIO helpers.
New drivers:
- WinSystems WS16C48
- Acces 104-DIO-48E
- F81866 (a F7188x variant)
- Qoric (a MPC8xxx variant)
- TS-4800
- SPI serializers (pisosr): simple 74xx shift registers connected
to SPI to obtain a dirt-cheap output-only GPIO expander.
- Texas Instruments TPIC2810
- Texas Instruments TPS65218
- Texas Instruments TPS65912
- X-Gene (ARM64) standby GPIO controller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9AJ4
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel v4.6. There is quite a
lot of interesting stuff going on.
The patches to other subsystems and arch-wide are ACKed as far as
possible, though I consider things like per-arch <asm/gpio.h> as
essentially a part of the GPIO subsystem so it should not be needed.
Core changes:
- The gpio_chip is now a *real device*. Until now the gpio chips
were just piggybacking the parent device or (gasp) floating in
space outside of the device model.
We now finally make GPIO chips devices. The gpio_chip will create
a gpio_device which contains a struct device, and this gpio_device
struct is kept private. Anything that needs to be kept private
from the rest of the kernel will gradually be moved over to the
gpio_device.
- As a result of making the gpio_device a real device, we have added
resource management, so devm_gpiochip_add_data() will cut down on
overhead and reduce code lines. A huge slew of patches convert
almost all drivers in the subsystem to use this.
- Building on making the GPIO a real device, we add the first step of
a new userspace ABI: the GPIO character device. We take small
steps here, so we first add a pure *information* ABI and the tool
"lsgpio" that will list all GPIO devices on the system and all
lines on these devices.
We can now discover GPIOs properly from userspace. We still have
not come up with a way to actually *use* GPIOs from userspace.
- To encourage people to use the character device for the future, we
have it always-enabled when using GPIO. The old sysfs ABI is still
opt-in (and can be used in parallel), but is marked as deprecated.
We will keep it around for the foreseeable future, but it will not
be extended to cover ever more use cases.
Cleanup:
- Bjorn Helgaas removed a whole slew of per-architecture <asm/gpio.h>
includes.
This dates back to when GPIO was an opt-in feature and no shared
library even existed: just a header file with proper prototypes was
provided and all semantics were up to the arch to implement. These
patches make the GPIO chip even more a proper device and cleans out
leftovers of the old in-kernel API here and there.
Still some cruft is left but it's very little now.
- There is still some clamping of return values for .get() going on,
but we now return sane values in the vast majority of drivers and
the errorpath is sanitized. Some patches for powerpc, blackfin and
unicore still drop in.
- We continue to switch the ARM, MIPS, blackfin, m68k local GPIO
implementations to use gpiochip_add_data() and cut down on code
lines.
- MPC8xxx is converted to use the generic GPIO helpers.
- ATH79 is converted to use the generic GPIO helpers.
New drivers:
- WinSystems WS16C48
- Acces 104-DIO-48E
- F81866 (a F7188x variant)
- Qoric (a MPC8xxx variant)
- TS-4800
- SPI serializers (pisosr): simple 74xx shift registers connected to
SPI to obtain a dirt-cheap output-only GPIO expander.
- Texas Instruments TPIC2810
- Texas Instruments TPS65218
- Texas Instruments TPS65912
- X-Gene (ARM64) standby GPIO controller"
* tag 'gpio-v4.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (194 commits)
Revert "Share upstreaming patches"
gpio: mcp23s08: Fix clearing of interrupt.
gpiolib: Fix comment referring to gpio_*() in gpiod_*()
gpio: pca953x: Fix pca953x_gpio_set_multiple() on 64-bit
gpio: xgene: Fix kconfig for standby GIPO contoller
gpio: Add generic serializer DT binding
gpio: uapi: use 0xB4 as ioctl() major
gpio: tps65912: fix bad merge
Revert "gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free"
gpio: omap: drop dev field from gpio_bank structure
gpio: mpc8xxx: Slightly update the code for better readability
gpio: mpc8xxx: Remove *read_reg and *write_reg from struct mpc8xxx_gpio_chip
gpio: mpc8xxx: Fixup setting gpio direction output
gpio: mcp23s08: Add support for mcp23s18
dt-bindings: gpio: altera: Fix altr,interrupt-type property
gpio: add driver for MEN 16Z127 GPIO controller
gpio: lp3943: Drop pin_used and lp3943_gpio_request/lp3943_gpio_free
gpio: timberdale: Switch to devm_ioremap_resource()
gpio: ts4800: Add IMX51 dependency
gpiolib: rewrite gpiodev_add_to_list
...
At boot time the regulator driver can be initialized before the
gpio, in which case the call to of_get_named_gpio will return
EPROBE_DEFER. This value is silently passed to regulator_register
which will return success, although the gpio is not registered
(regulator_ena_gpio_request not called) as the value passed is
detected as invalid. The gpio_regulator_probe will therefore
succeed win no gpio requested.
Signed-off-by: Mihai Mihalache <mihai.d.mihalache@intel.com>
Reviewed-by: Hans Holmberg <hans.holmberg@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prints the error number along with error message when any
error occurs. This help on getting the reason of failure
quickly from log without any code instrument.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some of platforms like Nvidia's Tegra210 Jetson-TX1 platform has
multiple PMW based regulators. Add support to have multiple instances
of the driver by not changing any global data of pwm regulator and
if required, making instance specific copy and then making changes.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With following equation for calculating
voltage_to_duty_cycle_percentage
100 - (((req_uV * 100) - (min_uV * 100)) / diff);
we get 0% for max_uV and 100% for min_uV.
Correcting this to
((req_uV * 100) - (min_uV * 100)) / diff;
to get proper duty cycle.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
OF interface provides to read the u32 value via standard interface
of_property_read_u32(). Use this API to read "regulator-min-microvolts"
and "regulator-max-microvolt".
This will make consistent with other property value reads.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a patch to fix incorrect clear of event register.
Signed-off-by: James Ban <James.Ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a patch to fix incorrect clear of event register.
Signed-off-by: James Ban <James.Ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add regulator ops callback for configuration of active-discharge
and provide necessarily information via regulator descriptor.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support to enable/disable active discharge of regulator via
machine constraints. This configuration is done when setting
machine constraint during regulator register and if regulator
driver implemented the callback ops.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add helper function to set the state of active-discharge of
regulator using regmap. The HW regulator driver can directly
use this by providing the necessary information in the regulator
descriptor.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support to enable/disable active discharge of regulator via
machine constraints. This configuration is done when setting
machine constraint during regulator register and if regulator
driver implemented the callback ops.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The documentation lists both 1.8V and 3.3V for this regulator output,
but 3.3V is mentioned more often and also matches what JZ4770 and
JZ4780 expect as an input.
Note that the voltage of REG9 is not programmable, so this commit only
changes the voltage reported in sysfs and debugfs, not the actual
output voltage of the hardware.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to preserve its value between calls. I guess this
was a copy-paste slip-up.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
These fields are never used and not required at all, remove them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This problem was introduced by:
commit daad134d66 ("regulator: core: Request GPIO before creating
sysfs entries")
The error path was not updated correctly after moving GPIO registration
code and in case regulator_ena_gpio_free failed, device_unregister() was
called even though device_register() was not yet called.
This problem breaks the boot at least on all Tegra 32-bit devices. It
will also crash each device that specifices GPIO that is unavaiable at
regulator_register call. Here's error log I've got when forced GPIO to
be invalid:
[ 1.116612] usb-otg-vbus-reg: Failed to request enable GPIO10: -22
[ 1.122794] Unable to handle kernel NULL pointer dereference at
virtual address 00000044
[ 1.130894] pgd = c0004000
[ 1.133598] [00000044] *pgd=00000000
[ 1.137205] Internal error: Oops: 5 [#1] SMP ARM
and here's backtrace from KDB:
Exception stack(0xef11fbd0 to 0xef11fc18)
fbc0: 00000000 c0738a14 00000000 00000000
fbe0: c0b2a0b0 00000000 00000000 c0738a14 c0b5fdf8 00000001 ef7f6074 ef11fc4c
fc00: ef11fc50 ef11fc20 c02a8344 c02a7f1c 60000013 ffffffff
[<c010cee0>] (__dabt_svc) from [<c02a7f1c>] (kernfs_find_ns+0x18/0xf8)
[<c02a7f1c>] (kernfs_find_ns) from [<c02a8344>] (kernfs_find_and_get_ns+0x40/0x58)
[<c02a8344>] (kernfs_find_and_get_ns) from [<c02ac4a4>] (sysfs_unmerge_group+0x28/0x68)
[<c02ac4a4>] (sysfs_unmerge_group) from [<c044389c>] (dpm_sysfs_remove+0x30/0x5c)
[<c044389c>] (dpm_sysfs_remove) from [<c0436ba8>] (device_del+0x48/0x1f4)
[<c0436ba8>] (device_del) from [<c0436d84>] (device_unregister+0x30/0x6c)
[<c0436d84>] (device_unregister) from [<c0403910>] (regulator_register+0x6d0/0xdac)
[<c0403910>] (regulator_register) from [<c04052d4>] (devm_regulator_register+0x50/0x84)
[<c04052d4>] (devm_regulator_register) from [<c0406298>] (reg_fixed_voltage_probe+0x25c/0x3c0)
[<c0406298>] (reg_fixed_voltage_probe) from [<c043d21c>] (platform_drv_probe+0x60/0xb0)
[<c043d21c>] (platform_drv_probe) from [<c043b078>] (driver_probe_device+0x24c/0x440)
[<c043b078>] (driver_probe_device) from [<c043b5e8>] (__device_attach_driver+0xc0/0x120)
[<c043b5e8>] (__device_attach_driver) from [<c043901c>] (bus_for_each_drv+0x6c/0x98)
[<c043901c>] (bus_for_each_drv) from [<c043ad20>] (__device_attach+0xac/0x138)
[<c043ad20>] (__device_attach) from [<c043b664>] (device_initial_probe+0x1c/0x20)
[<c043b664>] (device_initial_probe) from [<c043a074>] (bus_probe_device+0x94/0x9c)
[<c043a074>] (bus_probe_device) from [<c043a610>] (deferred_probe_work_func+0x80/0xcc)
[<c043a610>] (deferred_probe_work_func) from [<c01381d0>] (process_one_work+0x158/0x454)
[<c01381d0>] (process_one_work) from [<c013854c>] (worker_thread+0x38/0x510)
[<c013854c>] (worker_thread) from [<c013e154>] (kthread+0xe8/0x104)
[<c013e154>] (kthread) from [<c0108638>] (ret_from_fork+0x14/0x3c)
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@tieto.com>
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
regulator_attr_is_visible (which is a .is_visible callback of
regulator_dev_group attribute_grpup) checks rdev->ena_pin to decide if
"status" file should be present in sysfs. This field is set at the end
of regulator_ena_gpio_request so it has to be called before
device_register() otherwise this test will always fail, causing "status"
file to not be visible.
Since regulator_attr_is_visible also tests for is_enabled() op, this
problem is only visible for regulators that does not define this
callback, like regulator-fixed.c.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@tieto.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't print out an error with the driver sees EPROBE_DEFER when
attempting to get the gpio. These errors are usually transient; the
probe will be retried later.
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the s2mps11_info.rdev_num because it is not used outside of
probe.
Suggested-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
i2c_master_send() returns the number of bytes written on success.
So current code returns 2 if ad5398_write_reg() success.
This return value is propagated to .set_current_limit, .enable and .disable
callbacks of regulator_ops. This can be a problem, for example, if the
users test if the return value of regulator_set_current_limit() is 0.
Fix it by making ad5398_write_reg() return 0 on success.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
MAXIM Semiconductor's PMIC, MAX77620 and MAX20024 have the
multiple DCDC and LDOs. This supplies the power to different
components of the system.
Also these rails has configuration for ramp time, flexible
power sequence, slew rate etc.
Add regulator driver to access these rails via regulator APIs.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mallikarjun Kasoju <mkasoju@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Following BUILD_BUG_ON using a variable fails for some of the compilers
and optimization levels (reported for gcc 4.9):
var = ARRAY_SIZE(s2mps15_regulators);
BUILD_BUG_ON(S2MPS_REGULATOR_MAX < var);
Fix this by using ARRAY_SIZE directly.
Additionally add missing BUILD_BUG_ON check for S2MPS15 device (the
check ensures that internal arrays are big enough to hold data for all
of regulators on all devices).
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The s5m8767_pmic_probe() function calls s5m8767_get_register() to
read data without checking the return code, which produces a compile-time
warning when that data is accessed:
drivers/regulator/s5m8767.c: In function 's5m8767_pmic_probe':
drivers/regulator/s5m8767.c:924:7: error: 'enable_reg' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/regulator/s5m8767.c:944:30: error: 'enable_val' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This changes the s5m8767_get_register() function to return a -EINVAL
not just for an invalid register number but also for an invalid
regulator number, as both would result in returning uninitialized
data. The s5m8767_pmic_probe() function is then changed accordingly
to fail on a read error, as all the other callers of s5m8767_get_register()
already do.
In practice this probably cannot happen, as we don't call
s5m8767_get_register() with invalid arguments, but the gcc
warning seems valid in principle, in terms writing safe
error checking.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 9c4c60554a ("regulator: s5m8767: Convert to use regulator_[enable|disable|is_enabled]_regmap")
Signed-off-by: Mark Brown <broonie@kernel.org>
The vexpress regulator implementation is currently just called vexpress.
This is a problem because it clashes with another module with the same
name in hardware monitors.
This patch renames the vexpress regulator implementation to
vexpress-regulator so that there will be no clash in the module namespace.
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Reported-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Originally the helper macros used uppercase regulator names, which
are primarily used to expand to the regulator ID enum, as the default
names. This is aestheticly unpleasent.
Since the of_match bits are the same, just lowercase, use that as the
default names instead.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the regulator driver for hi655x PMIC.
Signed-off-by: Chen Feng <puck.chen@hisilicon.com>
Signed-off-by: Fei Wang <w.f@huawei.com>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Reviewed-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's perfectly valid to use the LTC3589 without an interrupt pin
connected to it. Currently, the driver probing fails when client->irq
is 0 (which means "no interrupt"). Don't register the interrupt
handler in that case but successfully finish the device probing instead.
Signed-off-by: Bernhard Walle <bernhard@bwalle.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The max77686 and max77802 regulator drivers are for sub-devices of a MFD
driver for some PMIC blocks. But the same object file name (max77686.o)
was used for both the common MFD driver and the max77686 regulator one.
This confuses kbuild if both drivers are built as module causing the MFD
driver to not be copied when installing the modules.
Also, max77{686,802} are a quite generic name for MFD subdevices drivers
so it is better to rename them to max77{686,802}-regulator like it's the
case for most regulator drivers.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The AXP223 is a new PMIC commonly paired with Allwinner A23/A33 SoCs.
It is functionally identical to AXP221; only the regulator default
voltage/status and the external host interface are different.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds support for TPS65912 PMIC regulators.
The regulators set consists of 4 DCDCs and 10 LDOs. The output
voltages are configurable and are meant to supply power to the
main processor and other components.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The old tps65912 driver is being replaced, delete old driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
LP872x regulators are made active via the EN pin, which might be hooked to a
GPIO. This adds support for driving the GPIO high when the driver is in use.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some devices don't hook the DVS pin to a GPIO but to ground or VCC.
In those cases, it is not a problem to have no DVS GPIO provided, as the current
code will already switch to software-only DVS selection:
When the DVS GPIO is invalid, lp872x_init_dvs jumps to the set_default_dvs_mode
label, which instructs the chip not to use the DVS pin at all and do it all in
software instead (by clearing the LP8720_EXT_DVS_M bit in the
LP872X_GENERAL_CFG register).
That is reflected later in the code, when setting the bucks (the DVS pin only
applies to the bucks) by checking for the LP8720_EXT_DVS_M bit on the
LP872X_GENERAL_CFG register (in lp872x_select_buck_vout_addr) to decide whether
to use software or hardware DVS selection.
Thus, there is no need to print a warning when the DVS GPIO is invalid.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds new regulator driver to support ACT8945A MFD
chip's regulators.
The ACT8945A has three step-down DC/DC converters and four
low-dropout regulators.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
AXP20X datasheet lists the possible voltage settings for LDO4, so
it was implemented using a voltage table. Upon closer examination,
the valid voltages can be mapped into 3 linear ranges.
Move AXP20X LDO4 to use linear ranges. The supporting code can be
reused with later AXP8xx PMICs, which have a number of regulators
that have 2 linear ranges.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Switch-type regulators, such as DC1SW on AXP22X, are a secondary output
from DCDC1. They are just an on/off switch, and the driver should not
try to read its voltage directly from the DCDC1 control registers.
Instead, the core will pass down the voltage from the regulator supply
chain.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Documentation/devicetree/bindings/regulator/mt6397-regulator.txt doc
mentions that a compatible "mediatek,mt6397-regulator" is required for
the MT6397 device node but the driver doesn't provide a OF match table so
the platform bus .match fallbacks to match using the driver name instead.
This also means that module auto-loading is broken for this driver since
the MFD driver that register the device, has a .of_compatible set so the
platform .uevent callback reports a OF modalias that's not in the module.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The platform bus_type .match callback attempts to match the platform device
name with an entry on the .id_table if provided and fallbacks to match with
the driver's name if a table is not provided.
Using a platform device ID to match is more explicit, allows the driver to
support more than one device and also the MODULE_DEVICE_TABLE macro can be
used to export the module aliases information instead of the MODULE_ALIAS.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As we now free the constraints in regulator_dev_release we will still
call free on the constraints pointer even if we went down an error
path in regulator_register, because it is only allocated after the
device_register. As such we no longer need to free rdev->constraints
on the error paths, so this patch removes said frees.
Fixes: 29f5f4860a ("regulator: core: Move more deallocation into class unregister")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Aside from a fix for a spurious warning (which caused more problems than
it fixed in the fixing really) this is all driver updates, including new
drivers for Dialog PV88060/90 and TI LM363x and TPS65086 devices. The
qcom_smd driver has had PM8916 and PMA8084 support added.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWlUWiAAoJECTWi3JdVIfQtywH/0joibyUbL34arXcPNCUUhlo
UnhTgT1kfOoS01ODt9gU49X4/8SRL9HdjcrIV8yTz4Ldb8by8Rd3ZrkO//9zs7BF
5PIqIzEw6FT/Ovsj8Tc35irccMSrwtTIGRrA8zrM/WtWQWcIUWFxMw+j/lewIvvH
jHZNTTLL5XemObSTfvzhbS6PZ8RcvRVXLNJjZYYO5xAEHNg3i5Hxao5p3QKzVJ8m
P5n4jSiTY/pVePcs9dzzQTGjlzkE11KX7DBxnmXOSPZsArSaRIC53DCmqu/JoG+o
3JJBkmRx7IJb0651hclFaUl8Wl56FSst+zigeAj82b301xpVR30iG3xiwYK/AT8=
=NQ6n
-----END PGP SIGNATURE-----
Merge tag 'regulator-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"Aside from a fix for a spurious warning (which caused more problems
than it fixed in the fixing really) this is all driver updates,
including new drivers for Dialog PV88060/90 and TI LM363x and TPS65086
devices. The qcom_smd driver has had PM8916 and PMA8084 support
added"
* tag 'regulator-v4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (36 commits)
regulator: core: remove some dead code
regulator: core: use dev_to_rdev
regulator: lp872x: Get rid of duplicate reference to DVS GPIO
regulator: lp872x: Add missing of_match in regulators descriptions
regulator: axp20x: Fix GPIO LDO enable value for AXP22x
regulator: lp8788: constify regulator_ops structures
regulator: wm8*: constify regulator_ops structures
regulator: da9*: constify regulator_ops structures
regulator: mt6311: Use REGCACHE_RBTREE
regulator: tps65917/palmas: Add bypass ops for LDOs with bypass capability
regulator: qcom-smd: Add support for PMA8084
regulator: qcom-smd: Add PM8916 support
soc: qcom: documentation: Update SMD/RPM Docs
regulator: pv88090: logical vs bitwise AND typo
regulator: pv88090: Fix irq leak
regulator: pv88090: new regulator driver
regulator: wm831x-ldo: Use platform_register/unregister_drivers()
regulator: wm831x-dcdc: Use platform_register/unregister_drivers()
regulator: lp8788-ldo: Use platform_register/unregister_drivers()
regulator: core: Fix nested locking of supplies
...
Setting the set_suspend_enable/disable callback to support
enable and disable the dcdc when system is suspend.
Signed-off-by: zhangqing <zhangqing@rock-chips.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Originally queue_delayed_work() used to negative error codes or 0 and 1
on success depending if the work was queued or not. It caused a lot of
bugs where people treated all non-zero returns as failures so we changed
it to return bool instead in d4283e9378 ('workqueue: make queueing
functions return bool'). Now it never returns failure.
Checking for negative values causes a static checker warning since it is
impossible based on the bool type.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The lp872x structure holds a reference to the DVS GPIO, but it is never actually
used anywhere, since a first reference exists from the lp872x_dvs structure.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to select the regulators via of_find_regulator_by_node (and thus use
them in devicetree), defining of_match for each regulator is required.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
The enable/disable values for GPIO LDOs are reversed. It seems no one
noticed as AXP22x support was introduced recently, and no one was using
the GPIO LDOs, either because no designs actually use them or board
support hasn't caught up.
Fixes: 1b82b4e4f9 ("regulator: axp20x: Add support for AXP22X regulators")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The regulator_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulator_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulator_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
This regulator is on a slow i2c bus. Register accesses are very simple,
they all either enable/disable a regulator channel, or select a new
voltage level. Thus, reading registers from the device will always
return what was last written.
Therefore we can save a lot of time when reading registers by using a
regmap_cache. Since the register map is relatively large, but we only
ever access a few of them, we use an RBTREE cache.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Acked-by: Henry Chen <henryc.chen@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
set/get_bypass ops were missing for ldo1/ldo2 on tps65917 and
ldo9 on palmas/tps659038 which support bypass mode.
Adding the bypass ops helps consumers configure these ldos in
bypass mode or remove bypass mode if need be.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reported-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support and documentation for the PMA8084 regulators
found on APQ8084 platforms.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support and documentation for the PM8916 regulators
found on MSM8916 platforms.
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
These were supposed to be bitwise AND instead of logical. Also kernel
style is for the operator to be on the first line and I removed some
extra parenthesis.
Fixes: c90456e36d ('regulator: pv88090: new regulator driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_request_threaded_irq to ensure the irq is freed when unload the
module.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the driver for the Powerventure PV88090 BUCKs and LDOs regulator.
It communicates via an I2C bus to the device.
Signed-off-by: James Ban <James.Ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These new helpers simplify implementing multi-driver modules and
properly handle failure to register one driver by unregistering all
previously registered drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These new helpers simplify implementing multi-driver modules and
properly handle failure to register one driver by unregistering all
previously registered drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These new helpers simplify implementing multi-driver modules and
properly handle failure to register one driver by unregistering all
previously registered drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit fa731ac7ea ("regulator: core: avoid unused variable warning")
introduced a subtle change in how supplies are locked. Where previously
code was always locking the regulator of the current iteration, the new
implementation only locks the regulator if it has a supply. For any
given power tree that means that the root will never get locked.
On the other hand the regulator_unlock_supply() will still release all
the locks, which in turn causes the lock debugging code to warn about a
mutex being unlocked which wasn't locked.
Cc: Mark Brown <broonie@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Fixes: Fixes: fa731ac7ea ("regulator: core: avoid unused variable warning")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The latest workaround for the lockdep interface's not using the second
argument of mutex_lock_nested() changed the loop missed locking the last
regulator due to a thinko with the loop termination condition exiting
one regulator too soon.
Reported-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make changes to allow this driver to work with the updated TPS65086 core
driver and bindings.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There were some missing "ret = " assignments here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As noticed by Geert Uytterhoeven, my patch to avoid a harmless build warning
in regulator_lock_supply() was total crap and introduced a real bug:
> [ BUG: bad unlock balance detected! ]
> kworker/u4:0/6 is trying to release lock (&rdev->mutex) at:
> [<c0247b84>] regulator_set_voltage+0x38/0x50
we still lock the regulator supplies, but not the actual regulators,
so we are missing a lock, and the unlock is unbalanced.
This rectifies it by first locking the regulator device itself before
using the same loop as before to lock its supplies.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 716fec9d1965 ("[SUBMITTED] regulator: core: avoid unused variable warning")
Signed-off-by: Mark Brown <broonie@kernel.org>
LM363X regulator driver supports LM3631 and LM3632.
LM3631 has 5 regulators. LM3632 provides 3 regulators.
One boost output and LDOs are used for the display module.
Boost voltage is configurable but always on.
Supported operations for LDOs are enabled/disabled and voltage change.
Two LDOs of LM3632 can be controlled by external pins.
Those are configured through the DT properties.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for TPS65218 LS3 current regulator, which is capable of 4
current input limit modes: 100, 200, 500, and 1000 uA.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_request_threaded_irq to ensure the irq is freed when unload the
module.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently S2MPSXX multifunction device is named as *-pmic,
and these MFDs also supports regulator as a one of its MFD cell which
has the same name, because current name is confusing and we want to
sort it out.
We did discussed different approaches about how the MFD and it
cells need to be named here [1].
Based in the discussion this patch rename MFD regulator name as
*-regulator instead of current *-pmic.
This patch also changes the corresponding entries in the regulator driver
to keep git-bisect happy.
[1]-> https://lkml.org/lkml/2015/10/28/417
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The S2MPS15 PMIC is similar in functionality to S2MPS11/14 PMIC. It contains
27 LDO and 10 Buck regulators and allows programming these regulators via a
I2C interface. This patch adds initial support for LDO/Buck regulators of
S2MPS15 PMIC.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This is the driver for the Powerventure PV88060 BUCKs and LDOs regulator.
It communicates via an I2C bus to the device.
Signed-off-by: James Ban <James.Ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The second argument of the mutex_lock_nested() helper is only
evaluated if CONFIG_DEBUG_LOCK_ALLOC is set. Otherwise we
get this build warning for the new regulator_lock_supply
function:
drivers/regulator/core.c: In function 'regulator_lock_supply':
drivers/regulator/core.c:142:6: warning: unused variable 'i' [-Wunused-variable]
To avoid the warning, this restructures the code to make it
both simpler and to move the 'i++' outside of the mutex_lock_nested
call, where it is now always used and the variable is not
flagged as unused.
We had some discussion about changing mutex_lock_nested to an
inline function, which would make the code do the right thing here,
but in the end decided against it, in order to guarantee that
mutex_lock_nested() does not introduced overhead without
CONFIG_DEBUG_LOCK_ALLOC.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 9f01cd4a91 ("regulator: core: introduce function to lock regulators and its supplies")
Link: http://permalink.gmane.org/gmane.linux.kernel/2068900
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit 7e50711993 ("mfd: tps6105x: Use i2c regmap to access
registers"), we can use regmap helper functions instead of open coded.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Denis Grigoryev <grigoryev@fastwel.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make it possible to use the bulk API with optional supplies, by allowing
the consumer to marking supplies as optional in the regulator_bulk_data.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fix the below build error:
drivers/regulator/mt6311-regulator.c:111: undefined reference to `__devm_regmap_init_i2c'
Signed-off-by: Henry Chen <henryc.chen@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Add support for TPS65086 PMIC regulators.
The regulators set consists of 3 Step-down Controllers, 3 Step-down
Converters, 3 LDOs, 3 Load Switches, and a Sink and Source LDO. The
output voltages are configurable and are meant to supply power to a
SoC and/or other components.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
Since we need to read voltages of parents as part of setting supply
voltages we need to be able to do get_voltage() internally without
taking locks so reorganize the locking to take locks on the full tree on
entry rather than as we recurse when called externally.
Reported-by: John Stultz <john.stultz@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver depends on MFD_STW481X but there isn't a build dependency so
it's a good idea to allow the driver to always be built when the
COMPILE_TEST option is enabled.
That way, the driver can be built with a config generated by make
allyesconfig and check if a patch would break the build.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown