Here is the big USB and PHY driver update for 4.16-rc1.
Along with the normally expected XHCI, MUSB, and Gadget driver patches,
there are some PHY driver fixes, license cleanups, sysfs attribute
cleanups, usbip changes, and a raft of other smaller fixes and
additions.
Full details are in the shortlog.
All of these have been in the linux-next tree for a long time with no
reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnL0Bg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymg8gCeLg/FMtc0S/xRR/56N/sbthEebcUAnROr9Sg3
55hDLdkyi93o9R86YOAJ
=8d2q
-----END PGP SIGNATURE-----
Merge tag 'usb-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB and PHY driver update for 4.16-rc1.
Along with the normally expected XHCI, MUSB, and Gadget driver
patches, there are some PHY driver fixes, license cleanups, sysfs
attribute cleanups, usbip changes, and a raft of other smaller fixes
and additions.
Full details are in the shortlog.
All of these have been in the linux-next tree for a long time with no
reported issues"
* tag 'usb-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (137 commits)
USB: serial: pl2303: new device id for Chilitag
USB: misc: fix up some remaining DEVICE_ATTR() usages
USB: musb: fix up one odd DEVICE_ATTR() usage
USB: atm: fix up some remaining DEVICE_ATTR() usage
USB: move many drivers to use DEVICE_ATTR_WO
USB: move many drivers to use DEVICE_ATTR_RO
USB: move many drivers to use DEVICE_ATTR_RW
USB: misc: chaoskey: Use true and false for boolean values
USB: storage: remove old wording about how to submit a change
USB: storage: remove invalid URL from drivers
usb: ehci-omap: don't complain on -EPROBE_DEFER when no PHY found
usbip: list: don't list devices attached to vhci_hcd
usbip: prevent bind loops on devices attached to vhci_hcd
USB: serial: remove redundant initializations of 'mos_parport'
usb/gadget: Fix "high bandwidth" check in usb_gadget_ep_match_desc()
usb: gadget: compress return logic into one line
usbip: vhci_hcd: update 'status' file header and format
USB: serial: simple: add Motorola Tetra driver
CDC-ACM: apply quirk for card reader
usb: option: Add support for FS040U modem
...
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
The tx_tasklet tasklet is used in invoke the hrtimer (task_timer) in
softirq context. This can be also achieved without the tasklet but
with HRTIMER_MODE_SOFT as hrtimer mode.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: keescook@chromium.org
Cc: linux-usb@vger.kernel.org
Link: http://lkml.kernel.org/r/20171221104205.7269-36-anna-maria@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Upon usb composition switch there is possibility of ep0 file
release happening after gadget driver bind. In case of composition
switch from adb to a non-adb composition gadget will never gets
bound again resulting into failure of usb device enumeration. Fix
this issue by checking FFS_FL_BOUND flag and avoid extra
gadget driver unbind if it is already done as part of composition
switch.
This fixes adb reconnection error reported on Android running
v4.4 and above kernel versions. Verified on Hikey running vanilla
v4.15-rc7 + few out of tree Mali patches.
Reviewed-at: https://android-review.googlesource.com/#/c/582632/
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg KH <gregkh@linux-foundation.org>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Dmitry Shmidt <dimitrysh@google.com>
Cc: Badhri <badhri@google.com>
Cc: Android Kernel Team <kernel-team@android.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
[AmitP: Cherry-picked it from android-4.14 and updated the commit log]
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Silences the following warnings:
drivers/usb/gadget/function/f_fs.c:1253:37: warning: incorrect type in argument 1 (different address spaces)
drivers/usb/gadget/function/f_fs.c:1253:37: expected void [noderef] <asn:1>*to
drivers/usb/gadget/function/f_fs.c:1253:37: got void *<noident>
drivers/usb/gadget/function/f_fs.c:2322:23: warning: cast to restricted __le32
drivers/usb/gadget/function/f_fs.c:2876:38: warning: cast to restricted __le32
drivers/usb/gadget/function/f_fs.c:272:12: warning: context imbalance in '__ffs_ep0_queue_wait' - unexpected unlock
drivers/usb/gadget/function/f_fs.c:450:17: warning: context imbalance in 'ffs_ep0_write' - different lock contexts for basic block
drivers/usb/gadget/function/f_fs.c:490:24: warning: context imbalance in '__ffs_ep0_read_events' - unexpected unlock
drivers/usb/gadget/function/f_fs.c:496:16: warning: context imbalance in 'ffs_ep0_read' - different lock contexts for basic block
Also, add an "unlocks spinlock" comment for consistency with existing ones.
No behaviour change is intended.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The kernel FIFO implementation, kfifo, provides interfaces to manipulate
a first-in-first-out circular buffer. Use kfifo instead of the homemade
one to make the code more concise and readable.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The specification says that the Reserved1 field in OS_DESC_EXT_COMPAT
must have the value "1", but when this feature was first implemented we
rejected any non-zero values.
This was adjusted to accept all non-zero values (while now rejecting
zero) in commit 53642399aa ("usb: gadget: f_fs: Fix wrong check on
reserved1 of OS_DESC_EXT_COMPAT"), but that breaks any userspace
programs that worked previously by returning EINVAL when Reserved1 == 0
which was previously the only value that succeeded!
If we just set the field to "1" ourselves, both old and new userspace
programs continue to work correctly and, as a bonus, old programs are
now compliant with the specification without having to fix anything
themselves.
Fixes: 53642399aa ("usb: gadget: f_fs: Fix wrong check on reserved1 of OS_DESC_EXT_COMPAT")
Cc: <stable@vger.kernel.org>
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
- proper use of the bool type (Thomas Meyer)
- constification of struct config_item_type (Bhumika Goyal)
-----BEGIN PGP SIGNATURE-----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=+tMO
-----END PGP SIGNATURE-----
Merge tag 'configfs-for-4.15' of git://git.infradead.org/users/hch/configfs
Pull configfs updates from Christoph Hellwig:
"A couple of configfs cleanups:
- proper use of the bool type (Thomas Meyer)
- constification of struct config_item_type (Bhumika Goyal)"
* tag 'configfs-for-4.15' of git://git.infradead.org/users/hch/configfs:
RDMA/cma: make config_item_type const
stm class: make config_item_type const
ACPI: configfs: make config_item_type const
nvmet: make config_item_type const
usb: gadget: configfs: make config_item_type const
PCI: endpoint: make config_item_type const
iio: make function argument and some structures const
usb: gadget: make config_item_type structures const
dlm: make config_item_type const
netconsole: make config_item_type const
nullb: make config_item_type const
ocfs2/cluster: make config_item_type const
target: make config_item_type const
configfs: make ci_type field, some pointers and function arguments const
configfs: make config_item_type const
configfs: Fix bool initialization/comparison
Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along with
phy and chipidea enhancements. There's also a lot of SPDX tags and
license boilerplate cleanups as well, which provide some churn in the
diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see happen.
All of these have been in linux-next with no reported issues for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgm/Vw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yktXwCdGgpInfOEvOGFd83EPDL7a1ncyc4AoM5wI8yl
1CeLipqVIN3IsMMJptvb
=zvDI
-----END PGP SIGNATURE-----
Merge tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along
with phy and chipidea enhancements. There's also a lot of SPDX tags
and license boilerplate cleanups as well, which provide some churn in
the diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see
happen.
All of these have been in linux-next with no reported issues for a
while"
* tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
usb: gadget: f_fs: Fix use-after-free in ffs_free_inst
USB: usbfs: compute urb->actual_length for isochronous
usb: core: message: remember to reset 'ret' to 0 when necessary
USB: typec: Remove remaining redundant license text
USB: typec: add SPDX identifiers to some files
USB: renesas_usbhs: rcar?.h: add SPDX tags
USB: chipidea: ci_hdrc_tegra.c: add SPDX line
USB: host: xhci-debugfs: add SPDX lines
USB: add SPDX identifiers to all remaining Makefiles
usb: host: isp1362-hcd: remove a couple of redundant assignments
USB: adutux: remove redundant variable minor
usb: core: add a new usb_get_ptm_status() helper
usb: core: add a 'type' parameter to usb_get_status()
usb: core: introduce a new usb_get_std_status() helper
usb: core: rename usb_get_status() 'type' argument to 'recip'
usb: core: add Status Type definitions
USB: gadget: Remove redundant license text
USB: gadget: function: Remove redundant license text
USB: gadget: udc: Remove redundant license text
USB: gadget: legacy: Remove redundant license text
...
KASAN enabled configuration reports an error
BUG: KASAN: use-after-free in ffs_free_inst+... [usb_f_fs] at addr ...
Write of size 8 by task ...
This is observed after "ffs-test" is run and interrupted. If after that
functionfs is unmounted and g_ffs module is unloaded, that use-after-free
occurs during g_ffs module removal.
Although the report indicates ffs_free_inst() function, the actual
use-after-free condition occurs in _ffs_free_dev() function, which
is probably inlined into ffs_free_inst().
This happens due to keeping the ffs_data reference in device structure
during functionfs unmounting, while ffs_data itself is freed as no longer
needed. The fix is to clear that reference in ffs_closed() function,
which is a counterpart of ffs_ready(), where the reference is stored.
Fixes: 3262ad8243 ("usb: gadget: f_fs: Stop ffs_closed NULL pointer dereference")
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Jerry Zhang <zhangjerry@google.com>
Cc: John Keeping <john@metanate.com>
Cc: Krzysztof Opasiak <k.opasiak@samsung.com>
Cc: Abdulhadi Mohamed <abdulahhadi2@gmail.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115004
Addresses-Coverity-ID: 115005
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not much going on this time around. With only 51 non-merge commits,
this was one of the smallest pull requests from the Gadget tree.
Most of the changes are in the mtu3 driver which added support for
36-bit DMA, support for USB 3.1 and support for dual-role (along with
some non-critical fixes).
The dwc2 driver got a few improvements to how we handle gadget state
tracking and also added support for STM32F7xx devices.
Other than that, we just some minor non-critical fixes and
improvements all over the place.
-----BEGIN PGP SIGNATURE-----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=nkak
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.15 merge window
Not much going on this time around. With only 51 non-merge commits,
this was one of the smallest pull requests from the Gadget tree.
Most of the changes are in the mtu3 driver which added support for
36-bit DMA, support for USB 3.1 and support for dual-role (along with
some non-critical fixes).
The dwc2 driver got a few improvements to how we handle gadget state
tracking and also added support for STM32F7xx devices.
Other than that, we just some minor non-critical fixes and
improvements all over the place.
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1350962
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 703128
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Make these structures const as they are only passed to the const
argument of the functions config_{group/item}_init_type_name.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Make this const as it is only stored in the const field of a structure
video_device in the file referencing it. Make the declaration const too.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Kmemleak checking configuration reports a memory leak in
usb_os_desc_prepare_interf_dir function when rndis function
instance is freed and then allocated again. For example, this
happens with FunctionFS driver with RNDIS function enabled
when "ffs-test" test application is run several times in a row.
The data for intermediate "os_desc" group for interface directories
is allocated as a single VLA chunk and (after a change of default
groups handling) is not ever freed and actually not stored anywhere
besides inside a list of default groups of a parent group.
The fix is to make usb_os_desc_prepare_interf_dir function return
a pointer to allocated data (as a pointer to the first VLA item)
instead of (an unused) integer and to make the caller component
(currently the only one is RNDIS function) responsible for storing
the pointer and freeing the memory when appropriate.
Fixes: 1ae1602de0 ("configfs: switch ->default groups to a linked list")
Cc: stable@vger.kernel.org
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
By submitting completed transfers to the system workqueue there is no
guarantee that completion events will be queued up in the correct order,
as in multi-processor systems there is a thread running for each
processor and the work items are not bound to a particular core.
This means that several completions are in the queue at the same time,
they may be processed in parallel and complete out of order, resulting
in data appearing corrupt when read by userspace.
Create a single-threaded workqueue for FunctionFS so that data completed
requests is passed to userspace in the order in which they complete.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As a holdover from the old g_file_storage gadget, the g_mass_storage
legacy gadget driver attempts to unregister itself when its main
operating thread terminates (if it hasn't been unregistered already).
This is not strictly necessary; it was never more than an attempt to
have the gadget fail cleanly if something went wrong and the main
thread was killed.
However, now that the UDC core manages gadget drivers independently of
UDC drivers, this scheme doesn't work any more. A simple test:
modprobe dummy-hcd
modprobe g-mass-storage file=...
rmmod dummy-hcd
ends up in a deadlock with the following backtrace:
sysrq: SysRq : Show Blocked State
task PC stack pid father
file-storage D 0 1130 2 0x00000000
Call Trace:
__schedule+0x53e/0x58c
schedule+0x6e/0x77
schedule_preempt_disabled+0xd/0xf
__mutex_lock.isra.1+0x129/0x224
? _raw_spin_unlock_irqrestore+0x12/0x14
__mutex_lock_slowpath+0x12/0x14
mutex_lock+0x28/0x2b
usb_gadget_unregister_driver+0x29/0x9b [udc_core]
usb_composite_unregister+0x10/0x12 [libcomposite]
msg_cleanup+0x1d/0x20 [g_mass_storage]
msg_thread_exits+0xd/0xdd7 [g_mass_storage]
fsg_main_thread+0x1395/0x13d6 [usb_f_mass_storage]
? __schedule+0x573/0x58c
kthread+0xd9/0xdb
? do_set_interface+0x25c/0x25c [usb_f_mass_storage]
? init_completion+0x1e/0x1e
ret_from_fork+0x19/0x24
rmmod D 0 1155 683 0x00000000
Call Trace:
__schedule+0x53e/0x58c
schedule+0x6e/0x77
schedule_timeout+0x26/0xbc
? __schedule+0x573/0x58c
do_wait_for_common+0xb3/0x128
? usleep_range+0x81/0x81
? wake_up_q+0x3f/0x3f
wait_for_common+0x2e/0x45
wait_for_completion+0x17/0x19
fsg_common_put+0x34/0x81 [usb_f_mass_storage]
fsg_free_inst+0x13/0x1e [usb_f_mass_storage]
usb_put_function_instance+0x1a/0x25 [libcomposite]
msg_unbind+0x2a/0x42 [g_mass_storage]
__composite_unbind+0x4a/0x6f [libcomposite]
composite_unbind+0x12/0x14 [libcomposite]
usb_gadget_remove_driver+0x4f/0x77 [udc_core]
usb_del_gadget_udc+0x52/0xcc [udc_core]
dummy_udc_remove+0x27/0x2c [dummy_hcd]
platform_drv_remove+0x1d/0x31
device_release_driver_internal+0xe9/0x16d
device_release_driver+0x11/0x13
bus_remove_device+0xd2/0xe2
device_del+0x19f/0x221
? selinux_capable+0x22/0x27
platform_device_del+0x21/0x63
platform_device_unregister+0x10/0x1a
cleanup+0x20/0x817 [dummy_hcd]
SyS_delete_module+0x10c/0x197
? ____fput+0xd/0xf
? task_work_run+0x55/0x62
? prepare_exit_to_usermode+0x65/0x75
do_fast_syscall_32+0x86/0xc3
entry_SYSENTER_32+0x4e/0x7c
What happens is that removing the dummy-hcd driver causes the UDC core
to unbind the gadget driver, which it does while holding the udc_lock
mutex. The unbind routine in g_mass_storage tells the main thread to
exit and waits for it to terminate.
But as mentioned above, when the main thread exits it tries to
unregister the mass-storage function driver. Via the composite
framework this ends up calling usb_gadget_unregister_driver(), which
tries to acquire the udc_lock mutex. The result is deadlock.
The simplest way to fix the problem is not to be so clever: The main
thread doesn't have to unregister the function driver. The side
effects won't be so terrible; if the gadget is still attached to a USB
host when the main thread is killed, it will appear to the host as
though the gadget's firmware has crashed -- a reasonably accurate
interpretation, and an all-too-common occurrence for USB mass-storage
devices.
In fact, the code to unregister the driver when the main thread exits
is specific to g-mass-storage; it is not used when f-mass-storage is
included as a function in a larger composite device. Therefore the
entire mechanism responsible for this (the fsg_operations structure
with its ->thread_exits method, the fsg_common_set_ops() routine, and
the msg_thread_exits() callback routine) can all be eliminated. Even
the msg_registered bitflag can be removed, because now the driver is
unregistered in only one place rather than in two places.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If usb_gadget_giveback_request() is called in usb_ep_queue(),
this printer_write() is possible to cause spinlock recursion. So,
this patch adds spin_unlock() before calls usb_ep_queue() to avoid it.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Pull more set_fs removal from Al Viro:
"Christoph's 'use kernel_read and friends rather than open-coding
set_fs()' series"
* 'work.set_fs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: unexport vfs_readv and vfs_writev
fs: unexport vfs_read and vfs_write
fs: unexport __vfs_read/__vfs_write
lustre: switch to kernel_write
gadget/f_mass_storage: stop messing with the address limit
mconsole: switch to kernel_read
btrfs: switch write_buf to kernel_write
net/9p: switch p9_fd_read to kernel_write
mm/nommu: switch do_mmap_private to kernel_read
serial2002: switch serial2002_tty_write to kernel_{read/write}
fs: make the buf argument to __kernel_write a void pointer
fs: fix kernel_write prototype
fs: fix kernel_read prototype
fs: move kernel_read to fs/read_write.c
fs: move kernel_write to fs/read_write.c
autofs4: switch autofs4_write to __kernel_write
ashmem: switch to ->read_iter
Instead use kernel_read/write consistently, which also makes sparse
happy.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Make this const as it is only used during a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
That quirk is required to make USB Ethernet gadget working on HW that
can't cope with unaligned DMA. For some reason only f_ncm sets up that
quirk, let's setup it directly in u_ether so other network models would
have that quirk applied as well. All network models have been tested with
ChipIdea UDC driver on NVIDIA Tegra20 SoC that require DMA to be aligned.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When the gadget serial device has no associated TTY, do not pass any
received data into the TTY layer for processing; simply drop it instead.
This prevents the TTY layer from calling back into the gadget serial
driver, which will then crash in e.g. gs_write_room() due to lack of
gadget serial device to TTY association (i.e. a NULL pointer dereference).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Users can apply i/o in the wrong direction on an
endpoint to stall it. In case there is an error
that does not allow the endpoint to be stalled,
we want the user to know.
An operation to stall the endpoint will return
EBADMSG if successful, EAGAIN if there are still
queued requests, and other errors depending on
the underlying implementation.
Also remove the conditional since it is always true.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This adds 3 new options to the RNDIS gadget function configs. It allows
overriding the default USB interface class/subclass/protocol.
The motivation for this is that if you set the values to "ef" (Misc),
"04" (RNDIS), "01" (Ethernet) respectively, then the device will be
recognized by the rndiscmp.inf file in Windows Vista and newer and will
cause Windows to load the correct RNDIS driver without the need for a
custom (signed) .inf file.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Currenly, f_midi_free uses snd_card_free, which will wait
until the user has released the sound card before
returning. However, if the user doesn't release the sound
card, then f_midi_free can block for an arbitrary amount
of time, which also blocks any gadget operations on that
thread.
Instead, we can use snd_card_free_when_closed which returns
before all handles are released. Since f_midi can be
accessed through rmidi if usb_put_function is called before
release_card_device, add refcounting to f_midi_free and
have rawmidi's private free call it. The f_midi memory
is only kfreed when usb_put_function and release_card_device
have both been called.
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add super speed descriptors for f_midi.
Signed-off-by: Badhri Jagan Sridharan <Badhri@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
These snd_rawmidi_ops structures are only passed as the third
argument of snd_rawmidi_set_ops. This argument is const, so the
snd_rawmidi_ops structures can be const too.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The current f_hid driver doesn't handle GET_PROCOTOL and
SET_PROCOTOL requests, which are required to operate HID
gadgets in BOOT mode. This patch implements this feature for
devices that have the same implementation for REPORT and BOOT mode
so that these devices are recognized by older BIOSes.
Signed-off-by: Abdulhadi Mohamed <abdulahhadi2@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
snd_pcm_ops are not supposed to change at runtime. All functions
working with snd_pcm_ops provided by <sound/pcm.h> work with
const snd_pcm_ops. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As per USB spec, multiple-bytes fields are stored
in little-endian order. Use CPU<->LE helpers for
such fields.
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As per USB spec, multiple-bytes fields are stored
in little-endian order. Use CPU<->LE helpers for
such fields.
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It is wrong to do --i in the for loop.
Fixes: dd02ea5a33 ("usb: gadget: mass_storage: Use static array for luns")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This development cycle resulted in a fair amount of changes in both
core and driver sides. The most significant change in ALSA core is
about PCM. Also the support of of-graph card and the new DAPM widget
for DSP are noteworthy changes in ASoC core. And there're lots of
small changes splat over the tree, as you can see in diffstat.
Below are a few highlights:
ALSA core:
- Removal of set_fs() hackery from PCM core stuff, and the code
reorganization / optimization thereafter
- Improved support of PCM ack ops, and a new ABI for improved
control/status mmap handling
- Lots of constifications in various codes
ASoC core:
- The support of of-graph card, which may work as a better generic
device for a replacement of simple-card
- New widget types intended mainly for use with DSPs
ASoC drivers:
- New drivers for Allwinner V3s SoCs
- Ensonic ES8316 codec support
- More Intel SKL and KBL works
- More device support for Intel SST Atom (mostly for cheap tablets and
2-in-1 devices)
- Support for Rockchip PDM controllers
- Support for STM32 I2S and S/PDIF controllers
- Support for ZTE AUD96P22 codecs
HD-audio:
- Support of new Realtek codecs (ALC215/ALC285/ALC289), more quirks
for HP and Dell machines
- A few more fixes for i915 component binding
Note that of-graph change may bring the conflicts with a later pull
request of devicetree, as currently found in linux-next.
-----BEGIN PGP SIGNATURE-----
iQJCBAABCAAsFiEECxfAB4MH3rD5mfB6bDGAVD0pKaQFAllbtmMOHHRpd2FpQHN1
c2UuZGUACgkQbDGAVD0pKaTMkhAAnqvRvh9nYBI1E2VGtJON/AFcsF4s6xdJd0ow
Bn5Kq/07rGWxAi8Cy69LM930eQrZl+xR69I7LMkC54BxVNhvhXNef7E5GXPbRi+3
l6dkBmkqvwmmHP5iiOxKtYSAnUfJitu1rmtAOVAjRh8rsWNeLuI8N8V/uilQBioi
lRywdBjdylub00H1DL8cmZHbrBb4pYrL/LepTswZL3I/UZ225fMiIGFd8tXpQPwZ
IKRZiuzrc3SykxSsL/aNeyxP+2qTYRtPfl/FGenKBBO2PJmGAb00yAdtQJRcD2eX
Xf1alfvpNgpy/U6+C7dJgNWQvvr+lPCaFXuMukIDno/zg/xD1V1Ev/fnbVEINLve
xMOnuJSGGaY6fu6eZ4Cck0VfZIj7UVA9x8zvBOKntIhq/VLfE7DDu3p9tiAZAVfH
nMOLAhy+0kFyHSrv6zVWQj+cmjPwLvaW7fNWVljL5/MWuF5GJi05DUOfV/vk8BaO
EnyVqe2ynzNLTsFpLHHy6XKgKtSTkPygxYSNuI7kSYAxD5qE6hXXKXTAqJ3LjDkO
tGiFmxp/vHrlNvcyRjXc30th/9PPj/mRBcJ2KyjXPa63L5ZW86PiyIHKxJA4yogv
y4z2ZlhIz90cZvpigFHtFqq1puVlDtKDbAaJ6AKrP8HEHUlMiPNApsSjWWBUcfzV
DXzrlg0=
=PUEh
-----END PGP SIGNATURE-----
Merge tag 'sound-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This development cycle resulted in a fair amount of changes in both
core and driver sides. The most significant change in ALSA core is
about PCM. Also the support of of-graph card and the new DAPM widget
for DSP are noteworthy changes in ASoC core. And there're lots of
small changes splat over the tree, as you can see in diffstat.
Below are a few highlights:
ALSA core:
- Removal of set_fs() hackery from PCM core stuff, and the code
reorganization / optimization thereafter
- Improved support of PCM ack ops, and a new ABI for improved
control/status mmap handling
- Lots of constifications in various codes
ASoC core:
- The support of of-graph card, which may work as a better generic
device for a replacement of simple-card
- New widget types intended mainly for use with DSPs
ASoC drivers:
- New drivers for Allwinner V3s SoCs
- Ensonic ES8316 codec support
- More Intel SKL and KBL works
- More device support for Intel SST Atom (mostly for cheap tablets
and 2-in-1 devices)
- Support for Rockchip PDM controllers
- Support for STM32 I2S and S/PDIF controllers
- Support for ZTE AUD96P22 codecs
HD-audio:
- Support of new Realtek codecs (ALC215/ALC285/ALC289), more quirks
for HP and Dell machines
- A few more fixes for i915 component binding"
* tag 'sound-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (418 commits)
ALSA: hda - Fix unbalance of i915 module refcount
ASoC: Intel: Skylake: Remove driver debugfs exit
ASoC: Intel: Skylake: explicitly add the headers sst-dsp.h
ALSA: hda/realtek - Remove GPIO_MASK
ALSA: hda/realtek - Fix typo of pincfg for Dell quirk
ALSA: pcm: add a documentation for tracepoints
ALSA: atmel: ac97c: fix error return code in atmel_ac97c_probe()
ALSA: x86: fix error return code in hdmi_lpe_audio_probe()
ASoC: Intel: Skylake: Add support to read firmware registers
ASoC: Intel: Skylake: Add sram address to sst_addr structure
ASoC: Intel: Skylake: Debugfs facility to dump module config
ASoC: Intel: Skylake: Add debugfs support
ASoC: fix semicolon.cocci warnings
ASoC: rt5645: Add quirk override by module option
ASoC: rsnd: make arrays path and cmd_case static const
ASoC: audio-graph-card: add widgets and routing for external amplifier support
ASoC: audio-graph-card: update bindings for amplifier support
ASoC: rt5665: calibration should be done before jack detection
ASoC: rsnd: constify dev_pm_ops structures.
ASoC: nau8825: change crosstalk-bypass property to bool type
...
Pull networking updates from David Miller:
"Reasonably busy this cycle, but perhaps not as busy as in the 4.12
merge window:
1) Several optimizations for UDP processing under high load from
Paolo Abeni.
2) Support pacing internally in TCP when using the sch_fq packet
scheduler for this is not practical. From Eric Dumazet.
3) Support mutliple filter chains per qdisc, from Jiri Pirko.
4) Move to 1ms TCP timestamp clock, from Eric Dumazet.
5) Add batch dequeueing to vhost_net, from Jason Wang.
6) Flesh out more completely SCTP checksum offload support, from
Davide Caratti.
7) More plumbing of extended netlink ACKs, from David Ahern, Pablo
Neira Ayuso, and Matthias Schiffer.
8) Add devlink support to nfp driver, from Simon Horman.
9) Add RTM_F_FIB_MATCH flag to RTM_GETROUTE queries, from Roopa
Prabhu.
10) Add stack depth tracking to BPF verifier and use this information
in the various eBPF JITs. From Alexei Starovoitov.
11) Support XDP on qed device VFs, from Yuval Mintz.
12) Introduce BPF PROG ID for better introspection of installed BPF
programs. From Martin KaFai Lau.
13) Add bpf_set_hash helper for TC bpf programs, from Daniel Borkmann.
14) For loads, allow narrower accesses in bpf verifier checking, from
Yonghong Song.
15) Support MIPS in the BPF selftests and samples infrastructure, the
MIPS eBPF JIT will be merged in via the MIPS GIT tree. From David
Daney.
16) Support kernel based TLS, from Dave Watson and others.
17) Remove completely DST garbage collection, from Wei Wang.
18) Allow installing TCP MD5 rules using prefixes, from Ivan
Delalande.
19) Add XDP support to Intel i40e driver, from Björn Töpel
20) Add support for TC flower offload in nfp driver, from Simon
Horman, Pieter Jansen van Vuuren, Benjamin LaHaise, Jakub
Kicinski, and Bert van Leeuwen.
21) IPSEC offloading support in mlx5, from Ilan Tayari.
22) Add HW PTP support to macb driver, from Rafal Ozieblo.
23) Networking refcount_t conversions, From Elena Reshetova.
24) Add sock_ops support to BPF, from Lawrence Brako. This is useful
for tuning the TCP sockopt settings of a group of applications,
currently via CGROUPs"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1899 commits)
net: phy: dp83867: add workaround for incorrect RX_CTRL pin strap
dt-bindings: phy: dp83867: provide a workaround for incorrect RX_CTRL pin strap
cxgb4: Support for get_ts_info ethtool method
cxgb4: Add PTP Hardware Clock (PHC) support
cxgb4: time stamping interface for PTP
nfp: default to chained metadata prepend format
nfp: remove legacy MAC address lookup
nfp: improve order of interfaces in breakout mode
net: macb: remove extraneous return when MACB_EXT_DESC is defined
bpf: add missing break in for the TCP_BPF_SNDCWND_CLAMP case
bpf: fix return in load_bpf_file
mpls: fix rtm policy in mpls_getroute
net, ax25: convert ax25_cb.refcount from atomic_t to refcount_t
net, ax25: convert ax25_route.refcount from atomic_t to refcount_t
net, ax25: convert ax25_uid_assoc.refcount from atomic_t to refcount_t
net, sctp: convert sctp_ep_common.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_transport.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_chunk.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_datamsg.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_auth_bytes.refcnt from atomic_t to refcount_t
...
The big news with this release is the of-graph card, this provides a
replacement for simple-card that is much more flexibile and scalable,
allowing many more systems to use a generic sound card than was possible
before:
- The of-graph card, finally merged after a long and dedicated effort
by Morimoto-san.
- New widget types intended mainly for use with DSPs.
- New drivers for Allwinner V3s SoCs, Ensonic ES8316, several classes
of x86 machine, Rockchip PDM controllers, STM32 I2S and S/PDIF
controllers and ZTE AUD96P22 CODECs.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAllaa7wTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0MhRB/0cIuUi/SmMSGz7cNKdDDArdpxHUV0U
dJb6qqhXCKeDQcx/34b1m+BnZpeT9au4Nt8HxOlLRbumcnuesYqfeBeZvuJhsC4I
q3e8e+idQlOp3+WM+snUXhWM4P/UsA9H4BaV1jvYSQW/C9WhfuLxsOraRiebLH7u
WJkmfeVjpzHHWzfDtpWJLHVroRLLMbOaz0e0Pw8/R1dfof0u27zKknqHOUcwRg0N
4+IWvKn3p59VE6eM6QUmruMZZCCfn2Hv5RygWf3LaHVlhA28BZi0dyMMSSSzVG6o
Im1Wm5z0dmmTfQKdNDU3PPBEKG6amTqF+2uuXOsq1I7vuiT+akHZbgWW
=F5BP
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v4.13
The big news with this release is the of-graph card, this provides a
replacement for simple-card that is much more flexibile and scalable,
allowing many more systems to use a generic sound card than was possible
before:
- The of-graph card, finally merged after a long and dedicated effort
by Morimoto-san.
- New widget types intended mainly for use with DSPs.
- New drivers for Allwinner V3s SoCs, Ensonic ES8316, several classes
of x86 machine, Rockchip PDM controllers, STM32 I2S and S/PDIF
controllers and ZTE AUD96P22 CODECs.
This time around we have a total of 57 non-merge commits. A list of
most important changes follows:
- Improvements to dwc3 tracing interface
- Initial dual-role support for dwc3
- Improvements to how we handle DMA resources in dwc3
- A new f_uac1 implementation which much more flexible
- Removal of AVR32 bits
- Improvements to f_mass_storage driver
-----BEGIN PGP SIGNATURE-----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=v6a5
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing
Felipe writes:
usb: changes for v4.13 merge window
This time around we have a total of 57 non-merge commits. A list of
most important changes follows:
- Improvements to dwc3 tracing interface
- Initial dual-role support for dwc3
- Improvements to how we handle DMA resources in dwc3
- A new f_uac1 implementation which much more flexible
- Removal of AVR32 bits
- Improvements to f_mass_storage driver
This patch adds a new function 'f_uac1'
(f_uac1 with virtual "ALSA card") that
uses recently created u_audio API. Comparing
to legacy f_uac1 function implementation it
doesn't require any real Audio codec to be
present on the device. In f_uac1 audio
streams are simply sinked to and sourced
from a virtual ALSA sound card created
using u_audio API.
Legacy f_uac1 approach is to write audio
samples directly to existing ALSA sound
card
f_uac1 approach is more generic/flexible
one - create an ALSA sound card that
represents USB Audio function and allows to
be used by userspace application that
may choose to do whatever it wants with the
data received from the USB Host and choose
to provide whatever it wants as audio data
to the USB Host.
f_uac1 also has capture support (gadget->host)
thanks to easy implementation via u_audio.
By default, capture interface has 48000kHz/2ch
configuration, same as playback channel has.
f_uac1 descriptors naming convention
uses f_uac2 driver naming convention that
makes it more common and meaningful.
Comparing to f_uac1_legacy, the f_uac1 doesn't
have volume/mute functionality. This is because
the f_uac1 volume/mute feature unit was dummy
implementation since that driver creation (2009)
and never had any real volume control or mute
functionality, so there is no any difference
here.
Since f_uac1 functionality, exposed
interface to userspace (virtual ALSA card),
input parameters are so different comparing
to f_uac1_legacy, that there is no any
reason to keep them in the same file/module,
and separate function was created.
g_audio can be built using one of existing
UAC functions (f_uac1, f_uac1_legacy or f_uac2)
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Before introducing new f_uac1 function (with virtual
ALSA card) make current implementation legacy.
This includes renaming of existing files, some
variables, config options and documentation
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Abstract the peripheral side ALSA sound card code from
the f_uac2 function into a component that can be called
by various functions, so the various flavors can be split
apart and selectively reused.
Visible changes:
- add uac_params structure to pass audio paramteres for
g_audio_setup
- make ALSA sound card's name configurable
- add [in/out]_ep_maxpsize
- allocate snd_uac_chip structure during g_audio_setup
- add u_audio_[start/stop]_[capture/playback] functions
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Simplify f_uac2 by removing platform driver/device
creation; use composite's usb_gadget device as
parent for sound card and for debug prints.
This removes extra layer of code without any functional
change.
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
After commit 7e4da3fcf7 ("usb: gadget: composite:
Test get_alt() presence instead of set_alt()") f_uac1
function became broken because it doesn't have
get_alt() callback implementation and composite
framework never set altsetting 1 for audiostreaming
interface. On host site it looks like:
[424339.017711] 21:1:1: usb_set_interface failed (-32)
Since host can't set altsetting 1, it can't start
playing audio.
In order to fix it implemented get_alt along with
minor improvements (error conditions checking)
similar to what existing f_uac2 has.
Cc: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
@@
expression SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- fn(SKB, LEN)[0]
+ *(u8 *)fn(SKB, LEN)
Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions (skb_put, __skb_put and pskb_put) return void *
and remove all the casts across the tree, adding a (u8 *) cast only
where the unsigned char pointer was used directly, all done with the
following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_put, __skb_put };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_put, __skb_put };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
which actually doesn't cover pskb_put since there are only three
users overall.
A handful of stragglers were converted manually, notably a macro in
drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many
instances in net/bluetooth/hci_sock.c. In the former file, I also
had to fix one whitespace problem spatch introduced.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were many places that my previous spatch didn't find,
as pointed out by yuan linyu in various patches.
The following spatch found many more and also removes the
now unnecessary casts:
@@
identifier p, p2;
expression len;
expression skb;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_zero(skb, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_zero(skb, len);
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, len);
|
-memset(p, 0, len);
)
@@
type t, t2;
identifier p, p2;
expression skb;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, sizeof(*p));
|
-memset(p, 0, sizeof(*p));
)
@@
expression skb, len;
@@
-memset(skb_put(skb, len), 0, len);
+skb_put_zero(skb, len);
Apply it to the tree (with one manual fixup to keep the
comment in vxlan.c, which spatch removed.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) The netlink attribute passed in to dev_set_alias() is not
necessarily NULL terminated, don't use strlcpy() on it. From
Alexander Potapenko.
2) Fix implementation of atomics in arm64 bpf JIT, from Daniel
Borkmann.
3) Correct the release of netdevs and driver private data in certain
circumstances.
4) Sanitize netlink message length properly in decnet, from Mateusz
Jurczyk.
5) Don't leak kernel data in rtnl_fill_vfinfo() netlink blobs. From
Yuval Mintz.
6) Hash secret is never initialized in ipv6 ILA translation code, from
Arnd Bergmann. I guess those clang warnings about unused inline
functions are useful for something!
7) Fix endian selection in bpf_endian.h, from Daniel Borkmann.
8) Sanitize sockaddr length before dereferncing any fields in AF_UNIX
and CAIF. From Mateusz Jurczyk.
9) Fix timestamping for GMAC3 chips in stmmac driver, from Mario
Molitor.
10) Do not leak netdev on dev_alloc_name() errors in mac80211, from
Johannes Berg.
11) Fix locking in sctp_for_each_endpoint(), from Xin Long.
12) Fix wrong memset size on 32-bit in snmp6, from Christian Perle.
13) Fix use after free in ip_mc_clear_src(), from WANG Cong.
14) Fix regressions caused by ICMP rate limiting changes in 4.11, from
Jesper Dangaard Brouer.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (91 commits)
i40e: Fix a sleep-in-atomic bug
net: don't global ICMP rate limit packets originating from loopback
net/act_pedit: fix an error code
net: update undefined ->ndo_change_mtu() comment
net_sched: move tcf_lock down after gen_replace_estimator()
caif: Add sockaddr length check before accessing sa_family in connect handler
qed: fix dump of context data
qmi_wwan: new Telewell and Sierra device IDs
net: phy: Fix MDIO_THUNDER dependencies
netconsole: Remove duplicate "netconsole: " logging prefix
igmp: acquire pmc lock for ip_mc_clear_src()
r8152: give the device version
net: rps: fix uninitialized symbol warning
mac80211: don't send SMPS action frame in AP mode when not needed
mac80211/wpa: use constant time memory comparison for MACs
mac80211: set bss_info data before configuring the channel
mac80211: remove 5/10 MHz rate code from station MLME
mac80211: Fix incorrect condition when checking rx timestamp
mac80211: don't look at the PM bit of BAR frames
i40e: fix handling of HW ATR eviction
...
Network devices can allocate reasources and private memory using
netdev_ops->ndo_init(). However, the release of these resources
can occur in one of two different places.
Either netdev_ops->ndo_uninit() or netdev->destructor().
The decision of which operation frees the resources depends upon
whether it is necessary for all netdev refs to be released before it
is safe to perform the freeing.
netdev_ops->ndo_uninit() presumably can occur right after the
NETDEV_UNREGISTER notifier completes and the unicast and multicast
address lists are flushed.
netdev->destructor(), on the other hand, does not run until the
netdev references all go away.
Further complicating the situation is that netdev->destructor()
almost universally does also a free_netdev().
This creates a problem for the logic in register_netdevice().
Because all callers of register_netdevice() manage the freeing
of the netdev, and invoke free_netdev(dev) if register_netdevice()
fails.
If netdev_ops->ndo_init() succeeds, but something else fails inside
of register_netdevice(), it does call ndo_ops->ndo_uninit(). But
it is not able to invoke netdev->destructor().
This is because netdev->destructor() will do a free_netdev() and
then the caller of register_netdevice() will do the same.
However, this means that the resources that would normally be released
by netdev->destructor() will not be.
Over the years drivers have added local hacks to deal with this, by
invoking their destructor parts by hand when register_netdevice()
fails.
Many drivers do not try to deal with this, and instead we have leaks.
Let's close this hole by formalizing the distinction between what
private things need to be freed up by netdev->destructor() and whether
the driver needs unregister_netdevice() to perform the free_netdev().
netdev->priv_destructor() performs all actions to free up the private
resources that used to be freed by netdev->destructor(), except for
free_netdev().
netdev->needs_free_netdev is a boolean that indicates whether
free_netdev() should be done at the end of unregister_netdevice().
Now, register_netdevice() can sanely release all resources after
ndo_ops->ndo_init() succeeds, by invoking both ndo_ops->ndo_uninit()
and netdev->priv_destructor().
And at the end of unregister_netdevice(), we invoke
netdev->priv_destructor() and optionally call free_netdev().
Signed-off-by: David S. Miller <davem@davemloft.net>
With the new API to perform the in-kernel buffer copy, we can get rid
of set_fs() usage in this driver, finally.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
f_mass_storage has a memorry barrier issue with the sleep and wake
functions that can cause a deadlock. This results in intermittent hangs
during MSC file transfer. The host will reset the device after receiving
no response to resume the transfer. This issue is seen when dwc3 is
processing 2 transfer-in-progress events at the same time, invoking
completion handlers for CSW and CBW. Also this issue occurs depending on
the system timing and latency.
To increase the chance to hit this issue, you can force dwc3 driver to
wait and process those 2 events at once by adding a small delay (~100us)
in dwc3_check_event_buf() whenever the request is for CSW and read the
event count again. Avoid debugging with printk and ftrace as extra
delays and memory barrier will mask this issue.
Scenario which can lead to failure:
-----------------------------------
1) The main thread sleeps and waits for the next command in
get_next_command().
2) bulk_in_complete() wakes up main thread for CSW.
3) bulk_out_complete() tries to wake up the running main thread for CBW.
4) thread_wakeup_needed is not loaded with correct value in
sleep_thread().
5) Main thread goes to sleep again.
The pattern is shown below. Note the 2 critical variables.
* common->thread_wakeup_needed
* bh->state
CPU 0 (sleep_thread) CPU 1 (wakeup_thread)
============================== ===============================
bh->state = BH_STATE_FULL;
smp_wmb();
thread_wakeup_needed = 0; thread_wakeup_needed = 1;
smp_rmb();
if (bh->state != BH_STATE_FULL)
sleep again ...
As pointed out by Alan Stern, this is an R-pattern issue. The issue can
be seen when there are two wakeups in quick succession. The
thread_wakeup_needed can be overwritten in sleep_thread, and the read of
the bh->state maybe reordered before the write to thread_wakeup_needed.
This patch applies full memory barrier smp_mb() in both sleep_thread()
and wakeup_thread() to ensure the order which the thread_wakeup_needed
and bh->state are written and loaded.
However, a better solution in the future would be to use wait_queue
method that takes care of managing memory barrier between waker and
waiter.
Cc: <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There were individual waitqueues for each epfile but eps_enable
would iterate through all of them, resulting in essentially the
same wakeup time.
The waitqueue represents the function being enabled, so a central
waitqueue in ffs_data makes more sense and is less redundant.
Also use wake_up_interruptible to reflect use of
wait_event_interruptible.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This allows users to make an ioctl call as the first action on a
connection. Ex, some functions might want to get endpoint size
before making any i/os.
Previously, calling ioctls before read/write would depending on the
timing of endpoints being enabled.
ESHUTDOWN is now a possible return value and ENODEV is not, so change
docs accordingly.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Jerry Zhang <zhangjerry@google.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Calculate wMaxPacketSize before endpoint matching the
descriptor is found.
This allows audio gadget to be used with controllers
which have a shortage or unavailability of endpoints
that can handle max packet size of 1023 (FS) or 1024
(HS).
With this audio gadget can be used on TI's OMAP-L138 SoC
which has a MUSB HS controller with endpoints having max
packet size much less than 1023 or 1024. See mode_2_cfg in
drivers/usb/musb/musb_core.c
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Companion descriptor is only used for SuperSpeed endpoints,
if the endpoints are HighSpeed or FullSpeed, the Companion
descriptor will not allocated, so we can only access it if
gadget is SuperSpeed.
I can reproduce this issue on Rockchip platform rk3368 SoC
which supports USB 2.0, and use functionfs for ADB. Kernel
build with CONFIG_KASAN=y and CONFIG_SLUB_DEBUG=y report
the following BUG:
==================================================================
BUG: KASAN: slab-out-of-bounds in ffs_func_set_alt+0x224/0x3a0 at addr ffffffc0601f6509
Read of size 1 by task swapper/0/0
============================================================================
BUG kmalloc-256 (Not tainted): kasan: bad access detected
----------------------------------------------------------------------------
Disabling lock debugging due to kernel taint
INFO: Allocated in ffs_func_bind+0x52c/0x99c age=1275 cpu=0 pid=1
alloc_debug_processing+0x128/0x17c
___slab_alloc.constprop.58+0x50c/0x610
__slab_alloc.isra.55.constprop.57+0x24/0x34
__kmalloc+0xe0/0x250
ffs_func_bind+0x52c/0x99c
usb_add_function+0xd8/0x1d4
configfs_composite_bind+0x48c/0x570
udc_bind_to_driver+0x6c/0x170
usb_udc_attach_driver+0xa4/0xd0
gadget_dev_desc_UDC_store+0xcc/0x118
configfs_write_file+0x1a0/0x1f8
__vfs_write+0x64/0x174
vfs_write+0xe4/0x200
SyS_write+0x68/0xc8
el0_svc_naked+0x24/0x28
INFO: Freed in inode_doinit_with_dentry+0x3f0/0x7c4 age=1275 cpu=7 pid=247
...
Call trace:
[<ffffff900808aab4>] dump_backtrace+0x0/0x230
[<ffffff900808acf8>] show_stack+0x14/0x1c
[<ffffff90084ad420>] dump_stack+0xa0/0xc8
[<ffffff90082157cc>] print_trailer+0x188/0x198
[<ffffff9008215948>] object_err+0x3c/0x4c
[<ffffff900821b5ac>] kasan_report+0x324/0x4dc
[<ffffff900821aa38>] __asan_load1+0x24/0x50
[<ffffff90089eb750>] ffs_func_set_alt+0x224/0x3a0
[<ffffff90089d3760>] composite_setup+0xdcc/0x1ac8
[<ffffff90089d7394>] android_setup+0x124/0x1a0
[<ffffff90089acd18>] _setup+0x54/0x74
[<ffffff90089b6b98>] handle_ep0+0x3288/0x4390
[<ffffff90089b9b44>] dwc_otg_pcd_handle_out_ep_intr+0x14dc/0x2ae4
[<ffffff90089be85c>] dwc_otg_pcd_handle_intr+0x1ec/0x298
[<ffffff90089ad680>] dwc_otg_pcd_irq+0x10/0x20
[<ffffff9008116328>] handle_irq_event_percpu+0x124/0x3ac
[<ffffff9008116610>] handle_irq_event+0x60/0xa0
[<ffffff900811af30>] handle_fasteoi_irq+0x10c/0x1d4
[<ffffff9008115568>] generic_handle_irq+0x30/0x40
[<ffffff90081159b4>] __handle_domain_irq+0xac/0xdc
[<ffffff9008080e9c>] gic_handle_irq+0x64/0xa4
...
Memory state around the buggy address:
ffffffc0601f6400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffffffc0601f6480: 00 00 00 00 00 00 00 00 00 00 06 fc fc fc fc fc
>ffffffc0601f6500: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffffffc0601f6580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffffffc0601f6600: fc fc fc fc fc fc fc fc 00 00 00 00 00 00 00 00
==================================================================
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Check for bad pointer that may result because of kthread_create failure.
This check is needed since the gserial setup callback function
(gs_console_setup()) is only freeing the info->con_buf in case of
kthread_create failure which will result into bad info->console_thread
pointer.
Without checking info->console_thread pointer validity in the
gserial_console_exit() function, before calling kthread_stop(), the
rmmod will generate Kernel Oops.
Signed-off-by: Bogdan Mirea <Bogdan-Stefan_mirea@mentor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch reworks the way f_mass_storage.c handles memory barriers
and synchronization:
The driver now uses a wait_queue instead of doing its own
task-state manipulations (even though only one task will ever
use the wait_queue).
The thread_wakeup_needed variable is removed. It was only a
source of trouble; although it was what the driver tested to
see whether it should wake up, what we really wanted to see
was whether a USB transfer had completed.
All the explicit memory barriers scattered throughout the
driver are replaced by a few calls to smp_load_acquire() and
smp_store_release().
The inreq_busy and outreq_busy fields are removed. In their
place, the driver keeps track of the current I/O direction by
splitting BUF_STATE_BUSY into two states: BUF_STATE_SENDING
and BUF_STATE_RECEIVING.
The buffer states are no longer protected by a lock. Mutual
exclusion isn't needed; the state is changed only by the
driver's main thread when it owns the buffer, and only by the
request completion routine when the gadget core owns the buffer.
The do_write() and throw_away_data() routines were reorganized
to make efficient use of the new sleeping mechanism. This
resulted in the removal of one indentation level in those
routines, making the patch appear to be more more complicated
than it really is.
In a few places, the driver allowed itself to be frozen although
it really shouldn't have (in the middle of executing a SCSI
command). Those places have been fixed.
The logic in the exception handler for aborting transfers and
waiting for them to stop has been simplified.
Tested-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch makes several adjustments to the way f_mass_storage.c
handles its internal state and asynchronous notifications (AKA
exceptions):
A number of states weren't being used for anything.
They are removed.
The FSG_STATE_IDLE state was renamed to FSG_STATE_NORMAL,
because it now applies whenever the gadget is operating
normally, not just when the gadget is idle.
The FSG_STATE_RESET state was renamed to
FSG_STATE_PROTOCOL_RESET, indicating that it represents a
Bulk-Only Transport protocol reset and not a general USB
reset.
When a signal arrives, it's silly for the signal handler to
send itself another signal! Now it takes care of everything
inline.
Along with an assortment of other minor changes in the same category.
Tested-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Here is the big USB patchset for 4.12-rc1.
Lots of good stuff here, after many many many attempts, the kernel
finally has a working typeC interface, many thanks to the Heikki and
Guenter and others who have taken the time to get this merged. It
wasn't an easy path for them at all.
There's also a staging driver that uses this new api, which is why it's
coming in through this tree.
Along with that, there's the usual huge number of changes for gadget
drivers, xhci, and other stuff. Johan also finally refactored pretty
much every driver that was looking at USB endpoints to do it in a common
way, which will help prevent any "badly-formed" devices from causing
problems in drivers. That too wasn't a simple task.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWQvEIQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yny4gCePCXxnrQdMWE+IMXf1H1hMubLkVkAn0ZWgQkq
BspgO7ZmGb+9Fpf6YvNz
=nwAu
-----END PGP SIGNATURE-----
Merge tag 'usb-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big USB patchset for 4.12-rc1.
Lots of good stuff here, after many many many attempts, the kernel
finally has a working typeC interface, many thanks to Heikki and
Guenter and others who have taken the time to get this merged. It
wasn't an easy path for them at all.
There's also a staging driver that uses this new api, which is why
it's coming in through this tree.
Along with that, there's the usual huge number of changes for gadget
drivers, xhci, and other stuff. Johan also finally refactored pretty
much every driver that was looking at USB endpoints to do it in a
common way, which will help prevent any "badly-formed" devices from
causing problems in drivers. That too wasn't a simple task.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
staging: typec: Fairchild FUSB302 Type-c chip driver
staging: typec: Type-C Port Controller Interface driver (tcpci)
staging: typec: USB Type-C Port Manager (tcpm)
usb: host: xhci: remove #ifdef around PM functions
usb: musb: don't mark of_dev_auxdata as initdata
usb: misc: legousbtower: Fix buffers on stack
USB: Revert "cdc-wdm: fix "out-of-sync" due to missing notifications"
usb: Make sure usb/phy/of gets built-in
USB: storage: e-mail update in drivers/usb/storage/unusual_devs.h
usb: host: xhci: print correct command ring address
usb: host: xhci: delete sp_dma_buffers for scratchpad
usb: host: xhci: using correct specification chapter reference for DCBAAP
xhci: switch to pci_alloc_irq_vectors
usb: host: xhci-plat: set resume_quirk() for R-Car controllers
usb: host: xhci-plat: add resume_quirk()
usb: host: xhci-plat: enable clk in resume timing
usb: host: plat: Enable xHCI plat runtime PM
USB: serial: ftdi_sio: add device ID for Microsemi/Arrow SF2PLUS Dev Kit
USB: serial: constify static arrays
usb: fix some references for /proc/bus/usb
...
Conflicts were simply overlapping changes. In the net/ipv4/route.c
case the code had simply moved around a little bit and the same fix
was made in both 'net' and 'net-next'.
In the net/sched/sch_generic.c case a fix in 'net' happened at
the same time that a new argument was added to qdisc_hash_add().
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull SCSI target fixes from Nicholas Bellinger:
"There has been work in a number of different areas over the last
weeks, including:
- Fix target-core-user (TCMU) back-end bi-directional handling (Xiubo
Li + Mike Christie + Ilias Tsitsimpis)
- Fix iscsi-target TMR reference leak during session shutdown (Rob
Millner + Chu Yuan Lin)
- Fix target_core_fabric_configfs.c race between LUN shutdown +
mapped LUN creation (James Shen)
- Fix target-core unknown fabric callback queue-full errors (Potnuri
Bharat Teja)
- Fix iscsi-target + iser-target queue-full handling in order to
support iw_cxgb4 RNICs. (Potnuri Bharat Teja + Sagi Grimberg)
- Fix ALUA transition state race between multiple initiator (Mike
Christie)
- Drop work-around for legacy GlobalSAN initiator, to allow QLogic
57840S + 579xx offload HBAs to work out-of-the-box in MSFT
environments. (Martin Svec + Arun Easi)
Note that a number are CC'ed for stable, and although the queue-full
bug-fixes required for iser-target to work with iw_cxgb4 aren't CC'ed
here, they'll be posted to Greg-KH separately"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
tcmu: Skip Data-Out blocks before gathering Data-In buffer for BIDI case
iscsi-target: Drop work-around for legacy GlobalSAN initiator
target: Fix ALUA transition state race between multiple initiators
iser-target: avoid posting a recv buffer twice
iser-target: Fix queue-full response handling
iscsi-target: Propigate queue_data_in + queue_status errors
target: Fix unknown fabric callback queue-full errors
tcmu: Fix wrongly calculating of the base_command_size
tcmu: Fix possible overwrite of t_data_sg's last iov[]
target: Avoid mappedlun symlink creation during lun shutdown
iscsi-target: Fix TMR reference leak during session shutdown
usb: gadget: Correct usb EP argument for BOT status request
tcmu: Allow cmd_time_out to be set to zero (disabled)
With 51 non-merge commits, this is one of the smallest USB Gadget pull
requests. Apart from your expected set of non-critical fixes, and
other miscellaneous items, we have most of the changes in dwc3 (52.5%)
with all other UDCs following with 34.8%.
As for the actual changes, the most important of them are all the
recent changes to reduce memory footprint of dwc3, bare minimum
dual-role support on dwc3 and reworked endpoint count and
initialization routines.
-----BEGIN PGP SIGNATURE-----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=wYOI
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.12
With 51 non-merge commits, this is one of the smallest USB Gadget pull
requests. Apart from your expected set of non-critical fixes, and
other miscellaneous items, we have most of the changes in dwc3 (52.5%)
with all other UDCs following with 34.8%.
As for the actual changes, the most important of them are all the
recent changes to reduce memory footprint of dwc3, bare minimum
dual-role support on dwc3 and reworked endpoint count and
initialization routines.
Currently ffs_dev::name can be either allocated by the client of
the ffs_dev structure or by the f_fs.c core itself. The former
is used by g_ffs while the latter happens with configfs.
Historically, g_ffs did not need to allocate separate buffer for
the name so what is now f_fs.c core never cared about freeing
that space. With configfs the name needs to be copied since the
memory is not guaranteed to be availeble after ffs_set_inst_name
finishes.
The complication is therefore here to avoid allocations in the
g_ffs case but it complicates the code inproportinally to
benefits it provides. In particular, g_ffs is considered
‘legacy’ so optimising for its sake is unlikely to be worth the
effort.
With that observation in mind, simplify the code by unifying the
code paths in g_ffs and configfs paths. Furthermore, instead of
allocating a new buffer for the name, simply embed it in the
ffs_dev structure. This further makes the memory management
less convoluted and error-prone.
The configfs interface for functionfs imposed a limit of 40
characters for the name so this results in a 41-byte buffer
added to the structure. (For short names this may lead to
wasted memory but the actual amount is not immediately obvious
and depends on pointer size and which slab buckets the structure
and name would fall into).
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Unless HW sets quirk_ep_out_aligned_size, gadget driver shouldn't make
any efforts towards aligning transfers. If the UDC needs, it *must*
set the quirk flag.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We have helpers for some of these, let's rely on them instead of open
coding what they do in u_ether.c
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Commit 76e0da34c7 ("usb-gadget/uvc: use per-attribute show and store
methods") caused a stringification of an undefined macro argument "aname",
so three UVC parameters (streaming_interval, streaming_maxpacket and
streaming_maxburst) were named "aname".
Add the definition of "aname" to the main macro and name the filenames as
originaly intended.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Mostly simple cases of overlapping changes (adding code nearby,
a function whose name changes, for example).
Signed-off-by: David S. Miller <davem@davemloft.net>
These files all use functions declared in interrupt.h, but currently rely
on implicit inclusion of this file (via netns/xfrm.h).
That won't work anymore when the flow cache is removed so include that
header where needed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects the argument in usb_ep_free_request as it is
mistakenly set to ep_out. It should be ep_in for status request.
Signed-off-by: Manish Narani <mnarani@xilinx.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This resolves a merge issue in the gadget code, and we want the USB
fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hidg->req should be accessed only with write_spinlock held as it is
set to NULL when we get disabled by host.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As per USB3.0 Specification "Table 9-20. Standard Endpoint Descriptor",
for interrupt and isochronous endpoints, wMaxPacketSize must be set to
1024 if the endpoint defines bMaxBurst to be greater than zero.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The streaming_maxburst module parameter is 0 offset (0..15)
so we must add 1 while using it for wBytesPerInterval
calculation for the SuperSpeed companion descriptor.
Without this host uvcvideo driver will always see the wrong
wBytesPerInterval for SuperSpeed uvc gadget and may not find
a suitable video interface endpoint.
e.g. for streaming_maxburst = 0 case it will always
fail as wBytePerInterval was evaluating to 0.
Cc: stable@vger.kernel.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The gadget code exports the bitfield for serial status changes
over the wire in its internal endianness. The fix is to convert
to little endian before sending it over the wire.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Tested-by: 家瑋 <momo1208@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit ac670a3a650b899fc020b81f63e810d06015b865.
This introduce bug we already fixed in
commit 53642399aa ("usb: gadget: f_fs: Fix wrong check on reserved1 wof OS_DESC_EXT_COMPAT")
Next FFS (adb) SS enumeration fail with Windows OS.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This reverts commit 4fbac5206a.
This commit breaks g_webcam when used with uvc-gadget [1].
The user space application (e.g. uvc-gadget) is responsible for
sending response to UVC class specific requests on control endpoint
in uvc_send_response() in uvc_v4l2.c.
The bad commit was causing a duplicate response to be sent with
incorrect response data thus causing UVC probe to fail at the host
and broken control transfer endpoint at the gadget.
[1] - git://git.ideasonboard.org/uvc-gadget.git
Cc: <stable@vger.kernel.org> # v4.9+
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If we're dealing with SuperSpeed endpoints, we need
to make sure to pass along the companion descriptor
and initialize fields needed by the Gadget
API. Eventually, f_fs.c should be converted to use
config_ep_by_speed() like all other functions,
though.
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to split <linux/sched/signal.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/signal.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Here is the big USB and PHY driver updates for 4.11-rc1.
Nothing major, just the normal amount of churn in the usb gadget and dwc
and xhci controllers, new device ids, new phy drivers, a new usb-serial
driver, and a few other minor changes in different USB drivers.
All have been in linux-next for a long time with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWK2lrg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykh7ACffotTJvB/gwpuSIWh6qhA8KQ9mH8AnjlxMafv
b5b3vfOXJ8/N0Go25VwI
=7fqN
-----END PGP SIGNATURE-----
Merge tag 'usb-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB and PHY driver updates for 4.11-rc1.
Nothing major, just the normal amount of churn in the usb gadget and
dwc and xhci controllers, new device ids, new phy drivers, a new
usb-serial driver, and a few other minor changes in different USB
drivers.
All have been in linux-next for a long time with no reported issues"
* tag 'usb-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (265 commits)
usb: cdc-wdm: remove logically dead code
USB: serial: keyspan: drop header file
USB: serial: io_edgeport: drop io-tables header file
usb: musb: add code comment for clarification
usb: misc: add USB251xB/xBi Hi-Speed Hub Controller Driver
usb: misc: usbtest: remove redundant check on retval < 0
USB: serial: upd78f0730: sort device ids
USB: serial: upd78f0730: add ID for EVAL-ADXL362Z
ohci-hub: fix typo in dbg_port macro
usb: musb: dsps: Manage CPPI 4.1 DMA interrupt in DSPS
usb: musb: tusb6010: Clean up tusb_omap_dma structure
usb: musb: cppi_dma: Clean up cppi41_dma_controller structure
usb: musb: cppi_dma: Clean up cppi structure
usb: musb: cppi41: Detect aborted transfers in cppi41_dma_callback()
usb: musb: dma: Add a DMA completion platform callback
drivers: usb: usbip: Add missing break statement to switch
usb: mtu3: remove redundant dev_err call in get_ssusb_rscs()
USB: serial: mos7840: fix another NULL-deref at open
USB: serial: console: clean up sanity checks
USB: serial: console: fix uninitialised spinlock
...
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- Implement wraparound-safe refcount_t and kref_t types based on
generic atomic primitives (Peter Zijlstra)
- Improve and fix the ww_mutex code (Nicolai Hähnle)
- Add self-tests to the ww_mutex code (Chris Wilson)
- Optimize percpu-rwsems with the 'rcuwait' mechanism (Davidlohr
Bueso)
- Micro-optimize the current-task logic all around the core kernel
(Davidlohr Bueso)
- Tidy up after recent optimizations: remove stale code and APIs,
clean up the code (Waiman Long)
- ... plus misc fixes, updates and cleanups"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (50 commits)
fork: Fix task_struct alignment
locking/spinlock/debug: Remove spinlock lockup detection code
lockdep: Fix incorrect condition to print bug msgs for MAX_LOCKDEP_CHAIN_HLOCKS
lkdtm: Convert to refcount_t testing
kref: Implement 'struct kref' using refcount_t
refcount_t: Introduce a special purpose refcount type
sched/wake_q: Clarify queue reinit comment
sched/wait, rcuwait: Fix typo in comment
locking/mutex: Fix lockdep_assert_held() fail
locking/rtmutex: Flip unlikely() branch to likely() in __rt_mutex_slowlock()
locking/rwsem: Reinit wake_q after use
locking/rwsem: Remove unnecessary atomic_long_t casts
jump_labels: Move header guard #endif down where it belongs
locking/atomic, kref: Implement kref_put_lock()
locking/ww_mutex: Turn off __must_check for now
locking/atomic, kref: Avoid more abuse
locking/atomic, kref: Use kref_get_unless_zero() more
locking/atomic, kref: Kill kref_sub()
locking/atomic, kref: Add kref_read()
locking/atomic, kref: Add KREF_INIT()
...
Here's the big pull request for the Gadget
API. Again the majority of changes sit in dwc2
driver. Most important changes contain a workaround
for GOTGCTL being wrong, a sleep-inside-spinlock fix
and the big series of cleanups on dwc2.
One important thing on dwc3 is that we don't anymore
need gadget drivers to cope with unaligned OUT
transfers for us. We have support for appending one
extra chained TRB to align transfer ourselves.
Apart from these, the usual set of typos,
non-critical fixes, etc.
-----BEGIN PGP SIGNATURE-----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=gk8j
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v4.11
Here's the big pull request for the Gadget
API. Again the majority of changes sit in dwc2
driver. Most important changes contain a workaround
for GOTGCTL being wrong, a sleep-inside-spinlock fix
and the big series of cleanups on dwc2.
One important thing on dwc3 is that we don't anymore
need gadget drivers to cope with unaligned OUT
transfers for us. We have support for appending one
extra chained TRB to align transfer ourselves.
Apart from these, the usual set of typos,
non-critical fixes, etc.
OS descriptor head, when flagged as provided, is accessed without
checking if it fits in provided buffer. Verify length before access.
Also, there are other places where buffer length it checked
after accessing offsets which are potentially past the end. Check
buffer length before as well to fail cleanly.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit: ba1582f222 ("usb: gadget: f_hid: use alloc_ep_req()")
we cannot allocate any requests in bind() as we check if we should
align request buffer based on endpoint descriptor which is assigned
in set_alt().
Allocating request in bind() function causes a NULL pointer
dereference.
This commit moves allocation of IN request from bind() to set_alt()
to prevent this issue.
Fixes: ba1582f222 ("usb: gadget: f_hid: use alloc_ep_req()")
Cc: stable@vger.kernel.org
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It is allowed by the USB specification to enabled same-address, opposite-
direction endpoints simultaneously, which means 30 non-zero endpoints
are allowed. So double eps_addrmap length to 30.
The original code only accepted 14 descriptors out of a likely intended 15
(as there are 15 endpoint addresses, ignoring direction), because the first
eps_addrmap entry is unused (it is a placeholder for endpoint zero). So
increase eps_addrmap length by one to 31.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Endpoint descriptors come in 2 sizes, struct usb_endpoint_descriptor being
the largest. Use bLength to stop on endpoint descriptor boundary, and not
2 bytes too far.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There are only two requests for uac2, it may not be enough at high
loading system which usb interrupt handler can't be serviced on
time, then the data will be lost since it is isoc transfer for audio.
In this patch, we introduce a parameter for the number for usb request,
and the user can override it if current number for request is not enough
for his/her use case.
Besides, update this parameter for legacy audio gadget and documentation.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As IN request has to be allocated in set_alt() and released in
disable() we cannot use mutex to protect it as we cannot sleep
in those funcitons. Let's replace this mutex with a spinlock.
Cc: stable@vger.kernel.org
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When we unlock our spinlock to copy data to user we may get
disabled by USB host and free the whole list of completed out
requests including the one from which we are copying the data
to user memory.
To prevent from this let's remove our working element from
the list and place it back only if there is sth left when we
finish with it.
Fixes: 99c5150058 ("usb: gadget: hidg: register OUT INT endpoint for SET_REPORT")
Cc: stable@vger.kernel.org
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Requests for out endpoint are allocated in bind() function
but never released.
This commit ensures that all pending requests are released
when we disable out endpoint.
Fixes: 99c5150058 ("usb: gadget: hidg: register OUT INT endpoint for SET_REPORT")
Cc: stable@vger.kernel.org
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If it is out of memory, we should return -ENOMEM;
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
pnp string is usually much shorter than 1k so let's stop wasting 1k of
memory for its buffer and make it dynamically alocated.
This also removes 1k len limitation for pnp_string and
adds a new line after string content if required.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Generally in SysFS and ConfigFS files are new line terminated.
Also most of USB functions adds a trailing newline to each attribute.
Let's follow this convention also in ethernet functions.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since we need to change the implementation, stop exposing internals.
Provide kref_read() to read the current reference count; typically
used for debug messages.
Kills two anti-patterns:
atomic_read(&kref->refcount)
kref->refcount.counter
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When zero endpoints are declared for a function, there is no endpoint
to disable, enable or free, so replace do...while loops with while loops.
Change pre-decrement to post-decrement to iterate the same number of times
when there are endpoints to process.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This fixes an error message that was probably copied and pasted. The same
message is used for both the in and out endpoints, so it makes it impossible
to know which one actually failed because both cases say "IN".
Make the out endpoint error message say "OUT".
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reserved1 is documented as expected to be set to 0, but this test fails
when it it set to 0. Reverse the condition.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When FUNCTIONFS_EVENTFD flag is set, __ffs_data_got_descs reads a 32bits,
little-endian value right after the fixed structure header, and passes it
to eventfd_ctx_fdget. Document this.
Also, rephrase a comment to be affirmative about the role of string
descriptor at index 0. Ref: USB 2.0 spec paragraph "9.6.7 String", and
also checked to still be current in USB 3.0 spec paragraph "9.6.9 String".
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Pull scsi target cleanups from Bart Van Assche:
"The changes here are:
- a few small bug fixes for the iSCSI and user space target drivers.
- minimize the target build time by about 30% by rearranging #include
directives
- fix the second argument passed to percpu_ida_alloc()
- reduce the number of false positive warnings reported by sparse
These patches pass Wu Fengguang's build bot tests and also the
linux-next tests"
* 'scsi-target-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/bvanassche/linux:
iscsi-target: Return error if unable to add network portal
target: Fix spelling mistake and unwrap multi-line text
target/iscsi: Fix double free in lio_target_tiqn_addtpg()
target/user: Fix use-after-free of tcmu_cmds if they are expired
target: Minimize #include directives
target/user: Add an #include directive
cxgbit: Add an #include directive
ibmvscsi_tgt: Add two #include directives
sbp-target: Add an #include directive
qla2xxx: Add an #include directive
configfs: Minimize #include directives
usb: gadget: Fix second argument of percpu_ida_alloc()
sbp-target: Fix second argument of percpu_ida_alloc()
target/user: Fix a data type in tcmu_queue_cmd()
target: Use NULL instead of 0 to represent a pointer
Pull vfs updates from Al Viro:
- more ->d_init() stuff (work.dcache)
- pathname resolution cleanups (work.namei)
- a few missing iov_iter primitives - copy_from_iter_full() and
friends. Either copy the full requested amount, advance the iterator
and return true, or fail, return false and do _not_ advance the
iterator. Quite a few open-coded callers converted (and became more
readable and harder to fuck up that way) (work.iov_iter)
- several assorted patches, the big one being logfs removal
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
logfs: remove from tree
vfs: fix put_compat_statfs64() does not handle errors
namei: fold should_follow_link() with the step into not-followed link
namei: pass both WALK_GET and WALK_MORE to should_follow_link()
namei: invert WALK_PUT logics
namei: shift interpretation of LOOKUP_FOLLOW inside should_follow_link()
namei: saner calling conventions for mountpoint_last()
namei.c: get rid of user_path_parent()
switch getfrag callbacks to ..._full() primitives
make skb_add_data,{_nocache}() and skb_copy_to_page_nocache() advance only on success
[iov_iter] new primitives - copy_from_iter_full() and friends
don't open-code file_inode()
ceph: switch to use of ->d_init()
ceph: unify dentry_operations instances
lustre: switch to use of ->d_init()
Two of the USB Gadgets were poking around in the internals of struct ida
in order to determine if it is empty. Add the appropriate abstraction.
Link: http://lkml.kernel.org/r/1480369871-5271-63-git-send-email-mawilcox@linuxonhyperv.com
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Konstantin Khlebnikov <koct9i@gmail.com>
Tested-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
from the ->drop_link method.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nOOH
-----END PGP SIGNATURE-----
Merge tag 'configfs-for-4.10' of git://git.infradead.org/users/hch/configfs
Pull configfs update from Christoph Hellwig:
"Just one simple change from Andrzej to drop the pointless return value
from the ->drop_link method"
* tag 'configfs-for-4.10' of git://git.infradead.org/users/hch/configfs:
fs: configfs: don't return anything from drop_link
Here's the big set of USB/PHY patches for 4.10-rc1.
A number of new drivers are here in this set of changes. We have a new
USB controller type "mtu3", a new usb-serial driver, and the usual churn
in the gadget subsystem and the xhci host controller driver, along with
a few other new small drivers added. And lots of little other changes
all over the USB and PHY driver tree. Full details are in the shortlog
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWFAxRg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynuLgCgsHgM/oba6UaVm1kmyN9V5e3PVjEAn34tRLht
R4enLi8Yv1bOWPdlrpzN
=3MGJ
-----END PGP SIGNATURE-----
Merge tag 'usb-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here's the big set of USB/PHY patches for 4.10-rc1.
A number of new drivers are here in this set of changes. We have a new
USB controller type "mtu3", a new usb-serial driver, and the usual
churn in the gadget subsystem and the xhci host controller driver,
along with a few other new small drivers added. And lots of little
other changes all over the USB and PHY driver tree. Full details are
in the shortlog
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (309 commits)
USB: serial: option: add dlink dwm-158
USB: serial: option: add support for Telit LE922A PIDs 0x1040, 0x1041
USB: OHCI: nxp: fix code warnings
USB: OHCI: nxp: remove useless extern declaration
USB: OHCI: at91: remove useless extern declaration
usb: misc: rio500: fix result type for error message
usb: mtu3: fix U3 port link issue
usb: mtu3: enable auto switch from U3 to U2
usbip: fix warning in vhci_hcd_probe/lockdep_init_map
usb: core: usbport: Use proper LED API to fix potential crash
usbip: add missing compile time generated files to .gitignore
usb: hcd.h: construct hub class request constants from simpler constants
USB: OHCI: ohci-pxa27x: remove useless functions
USB: OHCI: omap: remove useless extern declaration
USB: OHCI: ohci-omap: remove useless functions
USB: OHCI: ohci-s3c2410: remove useless functions
USB: cdc-acm: add device id for GW Instek AFG-125
fsl/usb: Workarourd for USB erratum-A005697
usb: hub: Wait for connection to be reestablished after port reset
usbip: vudc: Refactor init_vudc_hw() to be more obvious
...
Pass a task state as second argument to percpu_ida_alloc().
Fixes: commit 71e7ae8e1f ("usb-gadget/tcm: Conversion to percpu_ida tag pre-allocation")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
copy_from_iter_full(), copy_from_iter_full_nocache() and
csum_and_copy_from_iter_full() - counterparts of copy_from_iter()
et.al., advancing iterator only in case of successful full copy
and returning whether it had been successful or not.
Convert some obvious users. *NOTE* - do not blindly assume that
something is a good candidate for those unless you are sure that
not advancing iov_iter in failure case is the right thing in
this case. Anything that does short read/short write kind of
stuff (or is in a loop, etc.) is unlikely to be a good one.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Documentation/filesystems/configfs/configfs.txt says:
"When unlink(2) is called on the symbolic link, the source item is
notified via the ->drop_link() method. Like the ->drop_item() method,
this is a void function and cannot return failure."
The ->drop_item() is indeed a void function, the ->drop_link() is
actually not. This, together with the fact that the value of ->drop_link()
is silently ignored suggests, that it is the ->drop_link() return
type that should be corrected and changed to void.
This patch changes drop_link() signature and all its users.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
[hch: reverted reformatting of some code]
Signed-off-by: Christoph Hellwig <hch@lst.de>
udplite conflict is resolved by taking what 'net-next' did
which removed the backlog receive method assignment, since
it is no longer necessary.
Two entries were added to the non-priv ethtool operations
switch statement, one in 'net' and one in 'net-next, so
simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
One big merge this time with a total of 166 non-merge commits.
Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
second (22.5%). The remaining 9.3% are scattered on gadget drivers.
The most important changes for dwc2 are the peripheral side DMA support
implemented by Synopsys folks and support for the new IOT dwc2
compatible core from Synopsys.
In dwc3 land we have support for high-bandwidth, high-speed isochronous
endpoints and some non-critical fixes for large scatter lists.
Apart from these, we have our usual set of cleanups, non-critical fixes,
etc.
-----BEGIN PGP SIGNATURE-----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=5WN9
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.10 merge window
One big merge this time with a total of 166 non-merge commits.
Most of the work, by far, is on dwc2 this time (68.2%) with dwc3 a far
second (22.5%). The remaining 9.3% are scattered on gadget drivers.
The most important changes for dwc2 are the peripheral side DMA support
implemented by Synopsys folks and support for the new IOT dwc2
compatible core from Synopsys.
In dwc3 land we have support for high-bandwidth, high-speed isochronous
endpoints and some non-critical fixes for large scatter lists.
Apart from these, we have our usual set of cleanups, non-critical fixes,
etc.
Fix error message by checkpath.pl
open brace '{' following struct/enum go on the same line
Patch applied by running fix inplace capability of checkpatch:
checkpatch.pl -f *.[ch] --types OPEN_BRACE --fix-inplace
Signed-off-by: Anson Jacob <ansonjacob.aj@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Properly check the return code of ffs_func_revmap_intf() and
ffs_func_revmap_ep() for a non-negative value.
Instead of checking the return code, the comparison was performed for the last
parameter of the function calls, because of wrong parenthesis.
This also fixes the following static checker warning:
drivers/usb/gadget/function/f_fs.c:3152 ffs_func_req_match()
warn: always true condition '(((creq->wIndex)) >= 0) => (0-u16max >= 0)'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Hädicke <felixhaedicke@web.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add super speed descriptors to f_hid.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dev_kfree_skb_any() is used to free packets that are dropped by the
network stack. Therefore the function should not be used for packets
that have been successfully processed by the network stack. Instead
dev_consume_skb_any() has to be used for such consumed packets.
This separation helps to identify dropped packets.
Signed-off-by: Torsten Polle <tpolle@de.adit-jv.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Socket buffers should be linked to the (network) device that allocated
the buffers. __netdev_alloc_skb performs this task.
Signed-off-by: Torsten Polle <tpolle@de.adit-jv.com>
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Socket buffers should be linked to the (network) device that allocated
the buffers.
Signed-off-by: Torsten Polle <tpolle@de.adit-jv.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There is only one waiter for the completion, therefore there
is no need to use complete_all(). Let's make that clear by
using complete() instead of complete_all().
The usage pattern of the completion is:
waiter context waker context
reinit_completion()
usb_esp_queue()
wait_for_completion_interruptible()
ffs_ep0_complete()
complete()
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Use the more common logging mechanism.
Miscellanea:
o Realign multiline statements
o Coalesce format
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to Dave Miller "the networking stack has a
hard requirement that all SKBs which are transmitted
must have their completion signalled in a fininte
amount of time. This is because, until the SKB is
freed by the driver, it holds onto socket,
netfilter, and other subsystem resources."
In summary, this means that using TX IRQ throttling
for the networking gadgets is, at least, complex and
we should avoid it for the time being.
Cc: <stable@vger.kernel.org>
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
ep->mult is supposed to be set to Isochronous and
Interrupt Endapoint's multiplier value. This value
is computed from different places depending on the
link speed.
If we're dealing with HighSpeed, then it's part of
bits [12:11] of wMaxPacketSize. This case wasn't
taken into consideration before.
While at that, also make sure the ep->mult defaults
to one so drivers can use it unconditionally and
assume they'll never multiply ep->maxpacket to zero.
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the more common logging mechanism.
Miscellanea:
o Realign multiline statements
o Coalesce format
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
firewire-net:
- set min/max_mtu
- remove fwnet_change_mtu
nes:
- set max_mtu
- clean up nes_netdev_change_mtu
xpnet:
- set min/max_mtu
- remove xpnet_dev_change_mtu
hippi:
- set min/max_mtu
- remove hippi_change_mtu
batman-adv:
- set max_mtu
- remove batadv_interface_change_mtu
- initialization is a little async, not 100% certain that max_mtu is set
in the optimal place, don't have hardware to test with
rionet:
- set min/max_mtu
- remove rionet_change_mtu
slip:
- set min/max_mtu
- streamline sl_change_mtu
um/net_kern:
- remove pointless ndo_change_mtu
hsi/clients/ssi_protocol:
- use core MTU range checking
- remove now redundant ssip_pn_set_mtu
ipoib:
- set a default max MTU value
- Note: ipoib's actual max MTU can vary, depending on if the device is in
connected mode or not, so we'll just set the max_mtu value to the max
possible, and let the ndo_change_mtu function continue to validate any new
MTU change requests with checks for CM or not. Note that ipoib has no
min_mtu set, and thus, the network core's mtu > 0 check is the only lower
bounds here.
mptlan:
- use net core MTU range checking
- remove now redundant mpt_lan_change_mtu
fddi:
- min_mtu = 21, max_mtu = 4470
- remove now redundant fddi_change_mtu (including export)
fjes:
- min_mtu = 8192, max_mtu = 65536
- The max_mtu value is actually one over IP_MAX_MTU here, but the idea is to
get past the core net MTU range checks so fjes_change_mtu can validate a
new MTU against what it supports (see fjes_support_mtu in fjes_hw.c)
hsr:
- min_mtu = 0 (calls ether_setup, max_mtu is 1500)
f_phonet:
- min_mtu = 6, max_mtu = 65541
u_ether:
- min_mtu = 14, max_mtu = 15412
phonet/pep-gprs:
- min_mtu = 576, max_mtu = 65530
- remove redundant gprs_set_mtu
CC: netdev@vger.kernel.org
CC: linux-rdma@vger.kernel.org
CC: Stefan Richter <stefanr@s5r6.in-berlin.de>
CC: Faisal Latif <faisal.latif@intel.com>
CC: linux-rdma@vger.kernel.org
CC: Cliff Whickman <cpw@sgi.com>
CC: Robin Holt <robinmholt@gmail.com>
CC: Jes Sorensen <jes@trained-monkey.org>
CC: Marek Lindner <mareklindner@neomailbox.ch>
CC: Simon Wunderlich <sw@simonwunderlich.de>
CC: Antonio Quartulli <a@unstable.cc>
CC: Sathya Prakash <sathya.prakash@broadcom.com>
CC: Chaitra P B <chaitra.basappa@broadcom.com>
CC: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
CC: MPT-FusionLinux.pdl@broadcom.com
CC: Sebastian Reichel <sre@kernel.org>
CC: Felipe Balbi <balbi@kernel.org>
CC: Arvid Brodin <arvid.brodin@alten.se>
CC: Remi Denis-Courmont <courmisch@gmail.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ffs_func_eps_disable is called from atomic context so it cannot sleep
thus cannot grab a mutex. Change the handling of epfile->read_buffer
to use non-sleeping synchronisation method.
Reported-by: Chen Yu <chenyu56@huawei.com>
Signed-off-by: Michał Nazarewicz <mina86@mina86.com>
Fixes: 9353afbbfa ("buffer data from ‘oversized’ OUT requests")
Tested-by: John Stultz <john.stultz@linaro.org>
Tested-by: Chen Yu <chenyu56@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
epfile->ep is protected by ffs->eps_lock (not epfile->mutex) so clear it
while holding the spin lock.
Tested-by: John Stultz <john.stultz@linaro.org>
Tested-by: Chen Yu <chenyu56@huawei.com>
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If we don't guarantee that we will always get an
interrupt at least when we're queueing our very last
request, we could fall into situation where we queue
every request with 'no_interrupt' set. This will
cause the link to get stuck.
The behavior above has been triggered with g_ether
and dwc3.
Cc: <stable@vger.kernel.org>
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Pull more vfs updates from Al Viro:
">rename2() work from Miklos + current_time() from Deepa"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: Replace current_fs_time() with current_time()
fs: Replace CURRENT_TIME_SEC with current_time() for inode timestamps
fs: Replace CURRENT_TIME with current_time() for inode timestamps
fs: proc: Delete inode time initializations in proc_alloc_inode()
vfs: Add current_time() api
vfs: add note about i_op->rename changes to porting
fs: rename "rename2" i_op to "rename"
vfs: remove unused i_op->rename
fs: make remaining filesystems use .rename2
libfs: support RENAME_NOREPLACE in simple_rename()
fs: support RENAME_NOREPLACE for local filesystems
ncpfs: fix unused variable warning
CURRENT_TIME macro is not appropriate for filesystems as it
doesn't use the right granularity for filesystem timestamps.
Use current_time() instead.
CURRENT_TIME is also not y2038 safe.
This is also in preparation for the patch that transitions
vfs timestamps to use 64 bit time and hence make them
y2038 safe. As part of the effort current_time() will be
extended to do range checks. Hence, it is necessary for all
file system timestamps to use current_time(). Also,
current_time() will be transitioned along with vfs to be
y2038 safe.
Note that whenever a single call to current_time() is used
to change timestamps in different inodes, it is because they
share the same time granularity.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Felipe Balbi <balbi@kernel.org>
Acked-by: Steven Whitehouse <swhiteho@redhat.com>
Acked-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Acked-by: David Sterba <dsterba@suse.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This reverts commit c9ffc78745 as it was
reported to be broken.
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Jim Baxter <jim_baxter@mentor.com>
Cc: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This time around we have 92 non-merge commits. Most
of the changes are in drivers/usb/gadget (40.3%)
with drivers/usb/gadget/function being the most
active directory (27.2%).
As for UDC drivers, only dwc3 (26.5%) and dwc2
(12.7%) have really been active.
The most important changes for dwc3 are better
support for scatterlist and, again, throughput
improvements. While on dwc2 got some minor stability
fixes related to soft reset and FIFO usage.
Felipe Tonello has done some good work fixing up our
f_midi gadget and Tal Shorer has implemented a nice
API change for our ULPI bus.
Apart from these, we have our usual set of
non-critical fixes, spelling fixes, build warning
fixes, etc.
-----BEGIN PGP SIGNATURE-----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=vTFa
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.9 merge window
This time around we have 92 non-merge commits. Most
of the changes are in drivers/usb/gadget (40.3%)
with drivers/usb/gadget/function being the most
active directory (27.2%).
As for UDC drivers, only dwc3 (26.5%) and dwc2
(12.7%) have really been active.
The most important changes for dwc3 are better
support for scatterlist and, again, throughput
improvements. While on dwc2 got some minor stability
fixes related to soft reset and FIFO usage.
Felipe Tonello has done some good work fixing up our
f_midi gadget and Tal Shorer has implemented a nice
API change for our ULPI bus.
Apart from these, we have our usual set of
non-critical fixes, spelling fixes, build warning
fixes, etc.
This commit incorporates findings from
https://lkml.org/lkml/2016/4/25/594
The function has been modified to make sure we hold
the dev lock when accessing the net device pointer.
Acked-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dev->port_usb is checked for null pointer previously, so dev->port_usb
might be null during no zlp check, fix it by adding null pointer check.
Acked-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
the if statement in lb_modinit is unnecessary so we can totally
remove the variable ret and just return the return value from
the call to usb_function_register.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Linus Torvalds