Instead of just waiting and hoping, actually poll for the pll lock to be
acquired. As a bonus, this should be significantly faster than the
sleep.
Changes in v3:
- Added to the set
Cc: Sandeep Panda <spanda@codeaurora.org>
Reviewed-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180813213058.184821-6-sean@poorly.run
prepare() is the old-timey way to say pre_enable(). It should be called
before modeset. This fixes an issue where the panel on cheza must have
the regulator always-on/boot-on for it to work.
Changes in v3:
- Added to the set
Cc: Sandeep Panda <spanda@codeaurora.org>
Reviewed-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180813213058.184821-5-sean@poorly.run
This was hand-rolled in the first version, and will surely be useful as
we expand the driver to support more varied use cases.
Changes in v2:
- Change subject prefix s/panel/bridge/
- Downgrade warning in poll function to error message
- Fix DP_EDP_CONFIGURATION_SET write value (Sandeep)
- Mask upper 8 bits of msg->address (Sandeep)
- Check aux cmd status for errors after completing the send (Sandeep)
- Remove length check since it's covered in the aux status
- Flip the READ check in transfer to WRITE check + early exit
Changes in v3:
- Added to the set
- Wrapped (x) in WDATA/RDATA #defines
- Replace readx_poll* with regmap_read_poll*
Cc: Sandeep Panda <spanda@codeaurora.org>
Reviewed-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180813213058.184821-4-sean@poorly.run
Order registers by offset and rename bits & masks to match the
datasheet. This makes the driver a bit easier to grok and
cross-reference with the datasheet.
Changes in v3:
- Added to the set
Cc: Sandeep Panda <spanda@codeaurora.org>
Reviewed-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180813213058.184821-3-sean@poorly.run
This function name was changed to drm_connector_attach_encoder().
Unfortunately this driver was posted on the list before that change, and
applied after
Fixes: a095f15c00 ("drm/bridge: add support for sn65dsi86 bridge
driver")
Cc: Sandeep Panda <spanda@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Reviewed-by: Sandeep Panda <spanda@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180730174225.257255-1-seanpaul@chromium.org
Recently drm_mode_connector_attach_encoder changed it's name. The change
was not noticed by bridge author, as a result gcc reports compile error
on next branch.
Fixes: f38b7cca6d ("drm/bridge: tc358764: Add DSI to LVDS bridge driver")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180727094859.27727-1-a.hajda@samsung.com
Add support for TI's sn65dsi86 dsi2edp bridge chip.
The chip converts DSI transmitted signal to eDP signal,
which is fed to the connected eDP panel.
This chip can be controlled via either i2c interface or
dsi interface. Currently in driver all the control registers
are being accessed through i2c interface only.
Also as of now HPD support has not been added to bridge
chip driver.
Changes in v1:
- Split the dt-bindings and the driver support into separate patches
(Andrzej Hajda).
- Use of gpiod APIs to parse and configure gpios instead of obsolete ones
(Andrzej Hajda).
- Use macros to define the register offsets (Andrzej Hajda).
Changes in v2:
- Separate out edp panel specific HW resource handling from bridge
driver and create a separate edp panel drivers to handle panel
specific mode information and HW resources (Sean Paul).
- Replace pr_* APIs to DRM_* APIs to log error or debug information
(Sean Paul).
- Remove some of the unnecessary structure/variable from driver (Sean
Paul).
- Rename the function and structure prefix "sn65dsi86" to "ti_sn_bridge"
(Sean Paul / Rob Herring).
- Remove most of the hard-coding and modified the bridge init sequence
based on current mode (Sean Paul).
- Remove the existing function to retrieve the EDID data and
implemented this as an i2c_adapter and use drm_get_edid() (Sean Paul).
- Remove the dummy irq handler implementation, will add back the
proper irq handling later (Sean Paul).
- Capture the required enable gpios in a single array based on dt entry
instead of having individual descriptor for each gpio (Sean Paul).
Changes in v3:
- Remove usage of irq_gpio and replace it as "interrupts" property (Rob
Herring).
- Remove the unnecessary header file inclusions (Sean Paul).
- Rearrange the header files in alphabetical order (Sean Paul).
- Use regmap interface to perform i2c transactions.
- Update Copyright/License field and address other review comments
(Jordan Crouse).
Changes in v4:
- Update License/Copyright (Sean Paul).
- Add Kconfig and Makefile changes (Sean Paul).
- Drop i2c gpio handling from this bridge driver, since i2c sda/scl gpios
will be handled by i2c master.
- Update required supplies names.
- Remove unnecessary goto statements (Sean Paul).
- Add mutex lock to power_ctrl API to avoid race conditions (Sean
Paul).
- Add support to parse reference clk frequency from dt(optional).
- Update the bridge chip enable/disable sequence.
Changes in v5:
- Fixed Kbuild test service reported warnings.
Changes in v6:
- Use PM runtime based ref-counting instead of local ref_count mechanism
(Stephen Boyd).
- Clean up some debug logs and indentations (Sean Paul).
- Simplify dp rate calculation (Sean Paul).
- Add support to configure refclk based on input REFCLK pin or DACP/N
pin (Stephen Boyd).
Changes in v7:
- Use static supply entries instead of dynamic allocation (Andrzej
Hajda).
- Defer bridge driver probe if panel is not probed (Andrzej Hajda).
- Update of_graph APIs for correct node reference management. (Andrzej
Hajda).
- Remove local display_mode object (Andrzej Hajda).
- Remove version id check function from driver.
Changes in v8:
- Move dsi register/attach function to bridge driver probe (Andrzej
Hajda).
- Introduce a new helper function to write 16bit words into consecutive
registers (Andrzej Hajda).
- Remove unnecessary macros (Andrzej Hajda).
Changes in v9:
- Remove dsi register/attach from bridge probe, since dsi dev register
completion also waits for any panel or bridge to get added. This creates
deadlock situation when bridge driver calls dsi dev register and
attach before bridge add, in its probe function.
- Fix issues faced during testing of bridge driver on actual HW.
- Remove unnecessary initializations (Stephen Boyd).
- Use local refclk lut size instead of global macro (Sean Paul).
Changes in v10:
- Use refclk to determine if continuous dsi clock is needed or not.
Changes in v11:
- Read DPPLL_SRC register to determine continuous clock instead of
using refclk handle (Stephen Boyd).
Changes in v12:
- Explain in comment as in why dsi dev registration is done in
bridge_attach (Andrzej Hajda).
- Move HPD disable to bridge_pre_enable (Andrzej Hajda).
- Make panel/DDC exclusive until HPD support is added (Andrzej Hajda).
Changes in v13:
- eDP panels report EDID via DP-AUX channel, so remove support for
dedicated DDC line (Andrzej Hajda).
Changes in v14:
- Remove unnecessary drm_panel checks (Andrzej Hajda).
Signed-off-by: Sandeep Panda <spanda@codeaurora.org>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1532069642-21392-1-git-send-email-spanda@codeaurora.org
Right now, the DRM panel logic returns NULL when a panel pointing to
the passed OF node is not present in the list of registered panels.
Most drivers interpret this NULL value as -EPROBE_DEFER, but we are
about to modify the semantic of of_drm_find_panel() and let the
framework return -ENODEV when the device node we're pointing to has
a status property that is not equal to "okay" or "ok".
Let's first patch the of_drm_find_panel() implementation to return
ERR_PTR(-EPROBE_DEFER) instead of NULL and patch all callers to replace
the '!panel' check by an 'IS_ERR(panel)' one.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180509130042.9435-2-boris.brezillon@bootlin.com
The bridge loses its hw state when the cable is unplugged. If we detect
this case in the hpd handler, reset its state.
Reported-by: Rob Clark <robdclark@gmail.com>
Tested-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180703165648.120401-1-seanpaul@chromium.org
Current implementation does not guarantee packed pixel modes working
with every dongle. There are some dongles, which require selecting
the output mode explicitly.
Write proper values to registers in packed_pixel mode, based on how it
is done in vendor's code. Select output color space: RGB
(no packed pixel) or YCBCR422 (packed pixel).
This reverts commit e8b92efa62
("drm/bridge/sii8620: fix display of packed pixel modes in MHL2").
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530204243-6370-3-git-send-email-m.purski@samsung.com
Currently AVI infoframe is sent only in MHL3. However, some MHL2 dongles
need AVI infoframe to work correctly in either packed pixel mode or
non-packed pixel mode.
Send AVI infoframe in set_infoframes() in every case. Create an
infoframe using drm_hdmi_infoframe_from_display_mode() instead of
manually filling each infoframe structure's field.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530204243-6370-2-git-send-email-m.purski@samsung.com
- A reversion of a commit in drm/sun4i to fix a run-time fault.
- Various fixes to the sii8620 bridge.
- Small bugfix to correctly check stride in atmel-hlcdc.
-----BEGIN PGP SIGNATURE-----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=ngPr
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-fixes-2018-06-21' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Fixes for v4.18-rc2:
- A reversion of a commit in drm/sun4i to fix a run-time fault.
- Various fixes to the sii8620 bridge.
- Small bugfix to correctly check stride in atmel-hlcdc.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/787d4bef-a579-4046-d0fc-f8c2c5b80c25@linux.intel.com
Currently packed pixel modes in MHL2 can't be displayed. The device
automatically recognizes output format, so setting format other than
RGB causes failure. Fix it by writing proper values to registers.
Tested on MHL1 and MHL2 using various vendors' dongles both in
DVI and HDMI mode.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1516706239-9104-1-git-send-email-m.purski@samsung.com
We got a few conflicts in drm_atomic.c after merging the DRM writeback support,
now we need a backmerge to unlock develop development on drm-misc-next.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
This patch makes RC_CORE to be selected with this driver.
sil_sii8620 driver calls remote controller interfaces directly
so RC_CORE should be enabled mandatorily.
And some boards not using remote controller device don't really
need to know that RC_CORE config should be enabled to use sil_sii8620
driver only for HDMI.
Changelog v2:
- select INPUT because compiling will fail without INPUT.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1527154379-31886-1-git-send-email-inki.dae@samsung.com
MHL bridge is usually connected to TV via MHL dongle. Currently plugging
HDMI cable to dongle is handled improperly.
Fix it by splitting connecting of a dongle and a HDMI cable. The driver
should now handle unplugging a sink from a dongle and plugging a
different sink with new edid.
Tested on MHL1, MHL2 and MHL3 using various vendors' dongles both in
DVI and HDMI mode.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1516705996-8928-1-git-send-email-m.purski@samsung.com
HSIC initialization was taken from the vendor code. HSIC in MHL circuit
is not connected, so it is not possible to test it. Tests prove that
without HSIC the device works well. Therefore it can be removed.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1511968368-30884-1-git-send-email-m.purski@samsung.com
The vendor code waits for infoframe to detect video mode set by source.
We do not need to follow this pattern, because video mode information is
provided by drm core. As a result most of the infoframe handling
code can be removed.
Start transmission immediately after detecting stream on HDMI lines
in irq_scdt() function without waiting for infoframe interrupt.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1511956130-24482-1-git-send-email-m.purski@samsung.com
Buffer overflow error should not occur, as mode_fixup() callback
filters pixel clock value and it should never exceed 600000. However,
current implementation is not obviously safe and relies on
implementation of mode_fixup().
Make 'i' variable never reach unsafe value in order to avoid buffer
overflow error.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: bf1722ca ("drm/bridge/sii8620: rewrite hdmi start sequence")
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1511341718-6974-1-git-send-email-m.purski@samsung.com
There is no need to flip reset pin twice. Also delays can be changed to
values present in vendor's code.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Maciej Purski <m.purski@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180608060457.18357-1-a.hajda@samsung.com
-----BEGIN PGP SIGNATURE-----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=twst
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2018-06-06-1' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"This starts to support NVIDIA volta hardware with nouveau, and adds
amdgpu support for the GPU in the Kabylake-G (the intel + radeon
single package chip), along with some initial Intel icelake enabling.
Summary:
New Drivers:
- v3d - driver for broadcom V3D V3.x+ hardware
- xen-front - XEN PV display frontend
core:
- handle zpos normalization in the core
- stop looking at legacy pointers in atomic paths
- improved scheduler documentation
- improved aspect ratio validation
- aspect ratio support for 64:27 and 256:135
- drop unused control node code.
i915:
- Icelake (ICL) enabling
- GuC/HuC refactoring
- PSR/PSR2 enabling and fixes
- DPLL management refactoring
- DP MST fixes
- NV12 enabling
- HDCP improvements
- GEM/Execlist/reset improvements
- GVT improvements
- stolen memory first 4k fix
amdgpu:
- Vega 20 support
- VEGAM support (Kabylake-G)
- preOS scanout buffer reservation
- power management gfxoff support for raven
- SR-IOV fixes
- Vega10 power profiles and clock voltage control
- scatter/gather display support on CZ/ST
amdkfd:
- GFX9 dGPU support
- userptr memory mapping
nouveau:
- major refactoring for Volta GV100 support
tda998x:
- HDMI i2c CEC support
etnaviv:
- removed unused logging code
- license text cleanups
- MMU handling improvements
- timeout fence fix for 50 days uptime
tegra:
- IOMMU support in gr2d/gr3d drivers
- zpos support
vc4:
- syncobj support
- CTM, plane alpha and async cursor support
analogix_dp:
- HPD and aux chan fixes
sun4i:
- MIPI DSI support
tilcdc:
- clock divider fixes for OMAP-l138 LCDK board
rcar-du:
- R8A77965 support
- dma-buf fences fixes
- hardware indexed crtc/du group handling
- generic zplane property support
atmel-hclcdc:
- generic zplane property support
mediatek:
- use generic video mode function
exynos:
- S5PV210 FIMD variant support
- IPP v2 framework
- more HW overlays support"
* tag 'drm-next-2018-06-06-1' of git://anongit.freedesktop.org/drm/drm: (1286 commits)
drm/amdgpu: fix 32-bit build warning
drm/exynos: fimc: signedness bug in fimc_setup_clocks()
drm/exynos: scaler: fix static checker warning
drm/amdgpu: Use dev_info() to report amdkfd is not supported for this ASIC
drm/amd/display: Remove use of division operator for long longs
drm/amdgpu: Update GFX info structure to match what vega20 used
drm/amdgpu/pp: remove duplicate assignment
drm/sched: add rcu_barrier after entity fini
drm/amdgpu: move VM BOs on LRU again
drm/amdgpu: consistenly use VM moved flag
drm/amdgpu: kmap PDs/PTs in amdgpu_vm_update_directories
drm/amdgpu: further optimize amdgpu_vm_handle_moved
drm/amdgpu: cleanup amdgpu_vm_validate_pt_bos v2
drm/amdgpu: rework VM state machine lock handling v2
drm/amdgpu: Add runtime VCN PG support
drm/amdgpu: Enable VCN static PG by default on RV
drm/amdgpu: Add VCN static PG support on RV
drm/amdgpu: Enable VCN CG by default on RV
drm/amdgpu: Add static CG control for VCN on RV
drm/exynos: Fix default value for zpos plane property
...
The dw_hdmi_setup_rx_sense exported function should not use struct device
to recover the dw-hdmi context using drvdata, but take struct dw_hdmi
directly like other exported functions.
This caused a regression using Meson DRM on S905X since v4.17-rc1 :
Internal error: Oops: 96000007 [#1] PREEMPT SMP
[...]
CPU: 0 PID: 124 Comm: irq/32-dw_hdmi_ Not tainted 4.17.0-rc7 #2
Hardware name: Libre Technology CC (DT)
[...]
pc : osq_lock+0x54/0x188
lr : __mutex_lock.isra.0+0x74/0x530
[...]
Process irq/32-dw_hdmi_ (pid: 124, stack limit = 0x00000000adf418cb)
Call trace:
osq_lock+0x54/0x188
__mutex_lock_slowpath+0x10/0x18
mutex_lock+0x30/0x38
__dw_hdmi_setup_rx_sense+0x28/0x98
dw_hdmi_setup_rx_sense+0x10/0x18
dw_hdmi_top_thread_irq+0x2c/0x50
irq_thread_fn+0x28/0x68
irq_thread+0x10c/0x1a0
kthread+0x128/0x130
ret_from_fork+0x10/0x18
Code: 34000964 d00050a2 51000484 9135c042 (f864d844)
---[ end trace 945641e1fbbc07da ]---
note: irq/32-dw_hdmi_[124] exited with preempt_count 1
genirq: exiting task "irq/32-dw_hdmi_" (124) is an active IRQ thread (irq 32)
Fixes: eea034af90 ("drm/bridge/synopsys: dw-hdmi: don't clobber drvdata")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1527673438-20643-1-git-send-email-narmstrong@baylibre.com
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJa+mZEAAoJEAx081l5xIa+p/4P/3kIW0Zk6wO2HOF2u4TRZdhe
2b6yYP6ig1MMpLsJuRH2f8hnWl2f+CBzhwHaKbUni9ffY4TboOWeoYL5YWap2Pcp
MxRLBXBAI9+8zqqsrm/VB4gQL/Xp0nghN3CT1khLnMs38BkFUX7nASiSIknVIxj3
ux/95o0Tb2uYN886ILZCixPjmNUSgfNAyQuNNKRmT1EM3mgDZ2mc6BJoArPcCBqr
0vkekQA9+ZK4XYEHfjq/0CrVMLXhjaO05+BADK8A8WOtyvU+0xKjJjmQx0sQAd6L
Vcr+aMabJP8+3LeMDjIWqH0wUk6YqECwnUOoBkJFp5YTx+D1ff2RzmlWwvt9skIZ
4tmyFMfAn8XKkoSwa598/jamxOgTmMTIO8/6dJfO01sDgUvmTeR5z+ZTDG9FudFW
7Y2aHLMm19kitjqLDCpWBPmFGYVmfIsqA52qSgIjF4JVIurDk3PLRbQt++4k2j84
hLvYClJIs4ulTfmNRuBH4cVYtW5H5ohIkwP9L715Y+7ag/LUdQB1V6QsrX1bHEXg
KX1jP1UHqpUwNEQ9N2/1wVv1Ss7p7CKFY3C2UAMacRyymrws4McziPuXUalkBArs
royz2gRc5ykpbZ7Itlls43XlyMYxBeaogq+P2ODHouQMfDM21Gam/mpBPz3+t2c5
fo9rLqk3NqxPbHud1NJH
=4NJV
-----END PGP SIGNATURE-----
Merge drm-fixes-for-v4.17-rc6-urgent into drm-next
Need to backmerge some nouveau fixes to reduce
the nouveau -next conflicts a lot.
Signed-off-by: Dave Airlie <airlied@redhat.com>
UAPI Changes:
- Fix render node number regression from control node removal.
Driver Changes:
- Small header fix for virgl, used by qemu.
- Use vm_fault_t in qxl.
-----BEGIN PGP SIGNATURE-----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=LG6G
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2018-05-15' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v4.18:
UAPI Changes:
- Fix render node number regression from control node removal.
Driver Changes:
- Small header fix for virgl, used by qemu.
- Use vm_fault_t in qxl.
Signed-off-by: Dave Airlie <airlied@redhat.com>
# gpg: Signature made Tue 15 May 2018 06:16:03 PM AEST
# gpg: using RSA key FE558C72A67013C3
# gpg: Can't check signature: public key not found
Link: https://patchwork.freedesktop.org/patch/msgid/e63306b9-67a0-74ab-8883-08b3d9db72d2@mblankhorst.nl
- Add IPP v2 framework.
. it is a rewritten version of the Exynos mem-to-mem image processing
framework which supprts color space conversion, image up/down-scaling
and rotation. This new version replaces existing userspace API with
new easy-to-use and simple ones so we have already applied the use of
these API to real user, Tizen Platform[1], and also makes existing
Scaler, FIMC, GScaler and Rotator drivers to use IPP v2 core API.
And below are patch lists we have applied to a real user,
https://git.tizen.org/cgit/platform/adaptation/samsung_exynos/libtdm-exynos/log/?h=tizen&qt=grep&q=ipphttps://git.tizen.org/cgit/platform/adaptation/samsung_exynos/libtdm-exynos/commit/?h=tizen&id=b59be207365d10efd489e6f71c8a045b558c44fehttps://git.tizen.org/cgit/platform/kernel/linux-exynos/log/?h=tizen&qt=grep&q=ipp
TDM(Tizen Display Manager) is a Display HAL for Tizen platform.
Ps. Only real user using IPP API is Tizen.
[1] https://www.tizen.org/
- Two cleanups
. One is to just remove mode_set callback from MIPI-DSI driver
because drm_display_mode data is already available from crtc
atomic state.
. And other is to just use new return type, vm_fault_t
for page fault handler.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=M74Y
-----END PGP SIGNATURE-----
Merge tag 'exynos-drm-next-for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-next
- Add S5PV210 FIMD variant support.
- Add IPP v2 framework.
. it is a rewritten version of the Exynos mem-to-mem image processing
framework which supprts color space conversion, image up/down-scaling
and rotation. This new version replaces existing userspace API with
new easy-to-use and simple ones so we have already applied the use of
these API to real user, Tizen Platform[1], and also makes existing
Scaler, FIMC, GScaler and Rotator drivers to use IPP v2 core API.
And below are patch lists we have applied to a real user,
https://git.tizen.org/cgit/platform/adaptation/samsung_exynos/libtdm-exynos/log/?h=tizen&qt=grep&q=ipphttps://git.tizen.org/cgit/platform/adaptation/samsung_exynos/libtdm-exynos/commit/?h=tizen&id=b59be207365d10efd489e6f71c8a045b558c44fehttps://git.tizen.org/cgit/platform/kernel/linux-exynos/log/?h=tizen&qt=grep&q=ipp
TDM(Tizen Display Manager) is a Display HAL for Tizen platform.
Ps. Only real user using IPP API is Tizen.
[1] https://www.tizen.org/
- Two cleanups
. One is to just remove mode_set callback from MIPI-DSI driver
because drm_display_mode data is already available from crtc
atomic state.
. And other is to just use new return type, vm_fault_t
for page fault handler.
Signed-off-by: Dave Airlie <airlied@redhat.com>
# gpg: Signature made Mon 14 May 2018 14:23:53 AEST
# gpg: using RSA key 573834890C4312B8
# gpg: Can't check signature: public key not found
Link: https://patchwork.freedesktop.org/patch/msgid/1526276453-29879-1-git-send-email-inki.dae@samsung.com
The driver can work with or without extcon framework, but if extcon is
build as module, sii8620 should be build as module as well.
Fixes: 6888384421 ("drm/bridge/sii8620: use micro-USB cable detection logic to detect MHL")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180409062708.4326-1-a.hajda@samsung.com
Signed-off-by: Sean Paul <seanpaul@chromium.org>
adv7511_probe() is never called in atomic context.
This function is only set as ".probe" in struct i2c_driver.
Despite never getting called from atomic context, adv7511_probe()
calls mdelay() to busily wait.
This is not necessary and can be replaced with usleep_range() to
avoid busy waiting.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1523435622-4329-1-git-send-email-baijiaju1990@gmail.com
edid should be freed once it's finished being used.
Fixes: 56fe8b6f49 ("drm/bridge: Add RGB to VGA bridge support")
Cc: Rob Herring <robh@kernel.org>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: <stable@vger.kernel.org> # v4.9+
Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180420190007.1572-1-seanpaul@chromium.org
UAPI Changes:
- Add support for a generic plane alpha property to sun4i, rcar-du and atmel-hclcdc. (Maxime)
Core Changes:
- Stop looking at legacy plane->fb and crtc members in atomic drivers. (Ville)
- mode_valid return type fixes. (Luc)
- Handle zpos normalization in the core. (Peter)
Driver Changes:
- Implement CTM, plane alpha and generic async cursor support in vc4. (Stefan)
- Various fixes for HPD and aux chan in drm_bridge/analogix_dp. (Lin, Zain, Douglas)
- Add support for MIPI DSI to sun4i. (Maxime)
-----BEGIN PGP SIGNATURE-----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=9LYY
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2018-04-26' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v4.18:
UAPI Changes:
- Add support for a generic plane alpha property to sun4i, rcar-du and atmel-hclcdc. (Maxime)
Core Changes:
- Stop looking at legacy plane->fb and crtc members in atomic drivers. (Ville)
- mode_valid return type fixes. (Luc)
- Handle zpos normalization in the core. (Peter)
Driver Changes:
- Implement CTM, plane alpha and generic async cursor support in vc4. (Stefan)
- Various fixes for HPD and aux chan in drm_bridge/analogix_dp. (Lin, Zain, Douglas)
- Add support for MIPI DSI to sun4i. (Maxime)
Signed-off-by: Dave Airlie <airlied@redhat.com>
# gpg: Signature made Thu 26 Apr 2018 08:21:01 PM AEST
# gpg: using RSA key FE558C72A67013C3
# gpg: Can't check signature: public key not found
Link: https://patchwork.freedesktop.org/patch/msgid/b33da7eb-efc9-ae6f-6f69-b7acd6df6797@mblankhorst.nl
The "adjusted_mode" clock value (ie the real pixel clock) is more
accurate than "mode" clock value (ie the panel/bridge requested
clock value). It offers a better preciseness for timing
computations and allows to reduce the extra dsi bandwidth in
burst mode (from ~20% to ~10-12%, hw platform dependent).
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Yannick Fertré <yannick.fertre@st.com>
Tested-by: Yannick Fertré <yannick.fertre@st.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180125155504.8611-1-philippe.cornu@st.com
The method struct drm_connector_helper_funcs::mode_valid is defined
as returning an 'enum drm_mode_status' but the driver implementation
for this method uses an 'int' for it.
Fix this by using 'enum drm_mode_status' in the driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180424131453.1961-1-luc.vanoostenryck@gmail.com
The method struct drm_connector_helper_funcs::mode_valid is defined
as returning an 'enum drm_mode_status' but the driver implementation
for this method uses an 'int' for it.
Fix this by using 'enum drm_mode_status' in the driver too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180424131450.1910-1-luc.vanoostenryck@gmail.com
The ADV7511 has four 256-byte maps that can be accessed via the main I2C
ports. Each map has it own I2C address and acts as a standard slave
device on the I2C bus.
Allow a device tree node to override the default addresses so that
address conflicts with other devices on the same bus may be resolved at
the board description level.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1518544137-2742-6-git-send-email-kbingham@kernel.org
Some of the platform-specific stuff in rockchip_dp_poweron() needs to
happen before the generic code. Some needs to happen after. Let's
split the callback in two.
Specifically we can't start doing PSR work until _after_ the whole
controller is up, so don't set the enable until the end.
Cc: Kristian H. Kristensen <hoegsberg@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
[seanpaul added exynos change]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-23-enric.balletbo@collabora.com
The comments in analogix_dp_init_aux() claim that we're disabling aux
channel retries, but then right below it for Rockchip it sets them to
3. If we actually need 3 retries for Rockchip then we could adjust
the comment, but it seems more likely that we want the same retry
behavior across all platforms.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Cc: 征增 王 <wzz@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-21-enric.balletbo@collabora.com
The code in analogix_dp_transfer() that was supposed to print out:
AUX CH error happened
Was actually dead code. That's because the previous check (whether
the interrupt status indicated any errors) would have hit for all
errors anyway.
Let's combine the two error checks so we can actually see AUX CH
errors. We'll also downgrade the message to a warning since some of
these types of errors might be expected for some displays. If this
gets too noisy we can downgrade again to debug.
Cc: 征增 王 <wzz@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-20-enric.balletbo@collabora.com
The current user of the analogix power_off is "analogix_dp-rockchip".
That driver does this:
- deactivate PSR
- turn off a clock
Both of these things (especially deactive PSR) should be done before
we turn the PHY power off and turn off analog power. Let's move the
callback up.
Note that without this patch (and with
https://patchwork.kernel.org/patch/9553349/ [seanpaul: this patch was
not applied, but it seems like the race can still occur]), I experienced
an error in reboot testing where one thread was at:
rockchip_drm_psr_deactivate
rockchip_dp_powerdown
analogix_dp_bridge_disable
drm_bridge_disable
...and the other thread was at:
analogix_dp_send_psr_spd
analogix_dp_enable_psr
analogix_dp_psr_set
psr_flush_handler
The flush handler thread was finding AUX channel errors and eventually
reported "Failed to apply PSR", where I had a kgdb breakpoint. Presumably
the device would have eventually given up and shut down anyway, but it
seems better to fix the order to be more correct.
Cc: Kristian H. Kristensen <hoegsberg@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-19-enric.balletbo@collabora.com
It's too early to detect fast link training, if other step after it
failed, we will set fast_link flag to 1, and retry set_bridge again. In
this case we will power down and power up panel power supply, and we
will do fast link training since we have set fast_link flag to 1. In
fact, we should do full link training now, not the fast link training.
So we should move the fast link detection at the end of set_bridge.
Cc: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-18-enric.balletbo@collabora.com
Register ANALOGIX_DP_FUNC_EN_1(offset 0x18), Rockchip is different to
Exynos:
on Exynos edp phy,
BIT 7 MASTER_VID_FUNC_EN_N
BIT 6 reserved
BIT 5 SLAVE_VID_FUNC_EN_N
on Rockchip edp phy,
BIT 7 reserved
BIT 6 RK_VID_CAP_FUNC_EN_N
BIT 5 RK_VID_FIFO_FUNC_EN_N
So, we should do some private operations to Rockchip.
Cc: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-17-enric.balletbo@collabora.com
The STRM_VALID bit in register ANALOGIX_DP_SYS_CTL_3 may be unstable,
so we may hit the error log "Timeout of video streamclk ok" since
checked this unstable bit.
In fact, we can go continue and the streamclk is ok if we wait enough time,
it does no effect on display.
Let's change this error to warn.
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-16-enric.balletbo@collabora.com
There is no register named ANALOGIX_DP_PLL_CTL in Rockchip edp phy reg
list. We should use BIT_4 in ANALOGIX_DP_PD to control the pll power
instead of ANALOGIX_DP_PLL_CTL.
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-15-enric.balletbo@collabora.com
If we failed disable psr, it would hang the display until next psr
cycle coming. So we should restore psr->state when it failed.
Cc: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-14-enric.balletbo@collabora.com
AUX errors are caused by many different reasons. We may not know what
happened in aux channel on failure, so let's reset aux channel if some
errors occurred.
Cc: 征增 王 <wzz@rock-chips.com>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-13-enric.balletbo@collabora.com
There are some different bits between Rockchip and Exynos in register
"AUX_PD". This patch fixes the incorrect operations about it.
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-12-enric.balletbo@collabora.com
We need to check the dpcd write/read return value to see whether the
write/read was successful
Cc: Kristian H. Kristensen <hoegsberg@chromium.org>
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-11-enric.balletbo@collabora.com
Enhanced mode is required by the eDP 1.2 specification, and not doing it
early could result in a period of time where we have a link transmitting
idle packets without it. Since there is no reason to disable it, we just
enable it at the beginning of link training and then keep it on all the
time.
Cc: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-10-enric.balletbo@collabora.com
There was a 1ms delay to detect the hpd signal, which is too short to
detect a short pulse. This patch extends this delay to 100ms.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Cc: 征增 王 <wzz@rock-chips.com>
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-9-enric.balletbo@collabora.com
When panel is shut down, we should make sure edp can be disabled to avoid
undefined behavior.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-8-enric.balletbo@collabora.com
Following the correct power up sequence:
dp_pd=ff => dp_pd=7f => wait 10us => dp_pd=00
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-7-enric.balletbo@collabora.com
According to DP spec v1.3 chap 3.5.1.2 Link Training, Link Policy Maker
must first detect that the HPD signal is asserted high by the Downstream
Device before establishing a link with it.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-6-enric.balletbo@collabora.com
When we enable bridge failed, we have to retry it, otherwise we would get
the abnormal display.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-5-enric.balletbo@collabora.com
Panel would reset its setting when it powers down. It would forget the last
succeeded link training setting. So we can't use the last successful link
training setting to do fast link training. Let's reset fast_train_enable in
analogix_dp_bridge_disable();
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-4-enric.balletbo@collabora.com
We should check AUX_EN bit to confirm the AUX CH operation is completed.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-3-enric.balletbo@collabora.com
We need to enable video before analogix_dp_is_video_stream_on(), so
we can get the right video stream status.
We needed to increase the delay in the timeout loop because there is
random "Timeout of video streamclk ok" message happen when debug edp
panel, this time do not define in the spec.
Cc: 征增 王 <wzz@rock-chips.com>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180423105003.9004-2-enric.balletbo@collabora.com
Add a driver for Cadence DPI -> DSI bridge.
This driver only support a subset of Cadence DSI bridge capabilities.
This driver has been tested/debugged in a simulated environment which
explains why some of the features are missing. Here is a
non-exhaustive list of missing features:
* burst mode
* DPHY init/configuration steps
* support for additional input interfaces (SDI input)
DSI commands and non-burst video mode have been tested.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180421070846.10330-1-boris.brezillon@bootlin.com
Here is the big set of char/misc driver patches for 4.17-rc1.
There are a lot of little things in here, nothing huge, but all
important to the different hardware types involved:
- thunderbolt driver updates
- parport updates (people still care...)
- nvmem driver updates
- mei updates (as always)
- hwtracing driver updates
- hyperv driver updates
- extcon driver updates
- and a handfull of even smaller driver subsystem and individual
driver updates
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWsShSQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykNqwCfUbfvopswb1PesHCLABDBsFQChgoAniDa6pS9
kI8TN5MdLN85UU27Mkb6
=BzFR
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the big set of char/misc driver patches for 4.17-rc1.
There are a lot of little things in here, nothing huge, but all
important to the different hardware types involved:
- thunderbolt driver updates
- parport updates (people still care...)
- nvmem driver updates
- mei updates (as always)
- hwtracing driver updates
- hyperv driver updates
- extcon driver updates
- ... and a handful of even smaller driver subsystem and individual
driver updates
All of these have been in linux-next with no reported issues"
* tag 'char-misc-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (149 commits)
hwtracing: Add HW tracing support menu
intel_th: Add ACPI glue layer
intel_th: Allow forcing host mode through drvdata
intel_th: Pick up irq number from resources
intel_th: Don't touch switch routing in host mode
intel_th: Use correct method of finding hub
intel_th: Add SPDX GPL-2.0 header to replace GPLv2 boilerplate
stm class: Make dummy's master/channel ranges configurable
stm class: Add SPDX GPL-2.0 header to replace GPLv2 boilerplate
MAINTAINERS: Bestow upon myself the care for drivers/hwtracing
hv: add SPDX license id to Kconfig
hv: add SPDX license to trace
Drivers: hv: vmbus: do not mark HV_PCIE as perf_device
Drivers: hv: vmbus: respect what we get from hv_get_synint_state()
/dev/mem: Avoid overwriting "err" in read_mem()
eeprom: at24: use SPDX identifier instead of GPL boiler-plate
eeprom: at24: simplify the i2c functionality checking
eeprom: at24: fix a line break
eeprom: at24: tweak newlines
eeprom: at24: refactor at24_probe()
...
The cable_plugin member never receives an assignment, so it is always
false, which causes hdmi_enable_overflow_interrupts() to never
be called as per the logic below:
if (hdmi->cable_plugin && hdmi->sink_is_hdmi)
hdmi_enable_overflow_interrupts(hdmi);
This has been the case since the driver was originally introduced
in commit 9aaf880ed4 ("imx-drm: Add mx6 hdmi transmitter support").
Remove the cable_plugin element and the hdmi_enable_overflow_interrupts()
function that is never called.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> # On R-Car H3
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1518812170-22687-1-git-send-email-festevam@gmail.com
We currently wait for the panel to mirror our intended PSR state
before continuing on both PSR enter and PSR exit. This is really
only important to do when we're entering PSR, since we want to
be sure the last frame we pushed is being served from the panel's
internal fb before shutting down the soc blocks (vop/analogix).
This patch changes the behavior such that we only wait for the
panel to complete the PSR transition when we're entering PSR, and
to skip verification when we're exiting.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Cc: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309222327.18689-7-enric.balletbo@collabora.com
We would meet a short black screen when exit PSR with the full link
training, In this case, we should use fast link train instead of full
link training.
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
[dropped header reordering]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309222327.18689-6-enric.balletbo@collabora.com
There is a race between AUX CH bring-up and enabling bridge which will
cause link training to fail. To avoid hitting it, don't change psr state
while enabling the bridge.
Cc: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
[seanpaul fixed up the commit message a bit and renamed *_supported to *_enabled]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309222327.18689-4-enric.balletbo@collabora.com
Make sure the request PSR state takes effect in analogix_dp_send_psr_spd()
function, or print the sink PSR error state if we failed to apply the
requested PSR setting.
Cc: 征增 王 <wzz@rock-chips.com>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
[seanpaul changed timeout loop to a readx poll]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180309222327.18689-2-enric.balletbo@collabora.com
Currently MHL chip must be turned on permanently to detect MHL cable. It
duplicates micro-USB controller's (MUIC) functionality and consumes
unnecessary power. Lets use extcon attached to MUIC to enable MHL chip
only if it detects MHL cable.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The following happens when connection a DVI output driven
from the SiI9022 using a DVI-to-VGA adapter plug:
i2c i2c-0: sendbytes: NAK bailout.
i2c i2c-0: sendbytes: NAK bailout.
Then no picture. Apparently the I2C engine inside the SiI9022
is not smart enough to try to fall back to DDC I2C. Or the
vendor have not integrated the electronics properly. I don't
know which one it is.
After this, the I2C bus seems stalled and the first attempt to
read the status register fails, and the code returns with
negative return value, and the display fails to initialized.
Instead, retry status readout five times and continue even
if this fails.
Tested on the ARM Versatile Express with a DVI-to-VGA
connector, it now gives picture.
Introduce a helper struct device *dev variable to make
the code more readable.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180305101702.13441-1-linus.walleij@linaro.org
If there is another bridge after analogix_dp, then the connector object
should not be created. This fixes following timeouts on Exynos5420-based
Chromebook2 Peach-PIT board during boot:
exynos-dp 145b0000.dp-controller: AUX CH cmd reply timeout!
exynos-dp 145b0000.dp-controller: AUX CH enable timeout!
exynos-dp 145b0000.dp-controller: AUX CH enable timeout!
exynos-dp 145b0000.dp-controller: AUX CH enable timeout!
exynos-dp 145b0000.dp-controller: AUX CH enable timeout!
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180305085741.18896-4-m.szyprowski@samsung.com
The bridge does not need to be powered in analogix_dp_bind(), so
remove the calls to pm_runtime_get()/phy_power_on()/analogix_dp_init_dp()
as well as their power-off counterparts.
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: zain wang <wzz@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
[the patch originally just removed the power_on portion, seanpaul removed
the power off code as well as improved the commit message]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180305085741.18896-2-m.szyprowski@samsung.com
The Amlogic Meson GX SoCs, embedded the v2.01a controller, has been also
identified needing this workaround.
This patch adds the corresponding version to enable a single iteration for
this specific version.
Fixes: be41fc55f1 ("drm: bridge: dw-hdmi: Handle overflow workaround based on device version")
Acked-by: Archit Taneja <architt@codeaurora.org>
[narmstrong: s/identifies/identified and rebased against Jernej's change]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1519386277-25902-1-git-send-email-narmstrong@baylibre.com
The readl_poll_timeout() return value is 0 in case of success
so it is better to detect errors without taking care of the
return value sign.
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180204213624.18288-1-philippe.cornu@st.com
Since we are initing connector in the core driver and encoder in the
plat driver, let's clean them up in the right places.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180110162348.22765-3-thierry.escande@collabora.com
The driver that instantiates the bridge should own the drvdata, as all
driver model callbacks (probe, remove, shutdown, PM ops, etc.) are also
owned by its driver struct. Moreover, storing two different pointer
types in driver data depending on driver initialization status is barely
a good practice and in fact has led to many bugs in this driver.
Let's clean up this mess and change Analogix entry points to simply
accept some opaque struct pointer, adjusting their users at the same
time to avoid breaking the compilation.
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Acked-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180110162348.22765-2-thierry.escande@collabora.com
dw_hdmi shouldn't set drvdata since some drivers might need to store
it's own data there. Rework dw_hdmi in a way to return struct dw_hdmi
instead to store it in drvdata. This way drivers are responsible to
store and pass structure when needed.
Idea was taken from the following commit:
8242ecbd59 ("drm/bridge/synopsys: stop clobbering drvdata")
Cc: p.zabel@pengutronix.de
Cc: Laurent.pinchart@ideasonboard.com
Cc: hjc@rock-chips.com
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214200906.31509-6-jernej.skrabec@siol.net
Parts of PHY code could be useful also for custom PHYs. For example,
Allwinner A83T has custom PHY which is probably Synopsys gen2 PHY
with few additional memory mapped registers, so most of the Synopsys PHY
related code could be reused.
Functions exported here are actually not specific to Synopsys PHYs but
to DWC HDMI controller PHY interface. This means that even if the PHY is
completely custom, i.e. not designed by Synopsys, exported functions can
be useful.
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214200906.31509-5-jernej.skrabec@siol.net
Allwinner SoCs have dw hdmi controller v1.32a which exhibits same
magenta line issue as i.MX6Q and i.MX6DL. Enable workaround for it.
Tests show that one iteration is enough.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214200906.31509-4-jernej.skrabec@siol.net
Add support for the Synopsys DesignWare MIPI DSI version 1.31
Two registers need to be updated/added for supporting 1.31:
* PHY_TMR_CFG 0x9c (updated)
1.30 [31:24] phy_hs2lp_time
[23:16] phy_lp2hs_time
[14: 0] max_rd_time
1.31 [25:16] phy_hs2lp_time
[ 9: 0] phy_lp2hs_time
* PHY_TMR_RD_CFG 0xf4 (new)
1.31 [14: 0] max_rd_time
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180206084251.303-1-philippe.cornu@st.com
The dw_mipi_dsi_host_transfer() must return the number of
bytes transmitted/received on success instead of 0.
Note: As the read feature is not implemented, only the
transmitted number of bytes is returned for the moment.
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180125103800.1999-3-philippe.cornu@st.com
The dcs/generic dsi read feature is not yet implemented so it
is important to warn the host_transfer() caller in case of
read operation requests.
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180125103800.1999-2-philippe.cornu@st.com
It's been a while since we've backmerged drm-next. Dave just brought
back 4.15-rc8, so now's a good time to freshen things up around here.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171031142149.32512-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
We're filling the "remainder" word with little-endian data, then writing
it out to IO registers with endian-correcting writel(). That probably
won't work on big-endian systems.
Let's mark the "remainder" variable as LE32 (since we fill it with
memcpy()) and do the swapping explicitly.
Some of this function could be done more easily without memcpy(), but
the unaligned "remainder" case is a little hard to do without
potentially overrunning 'tx_buf', so I just applied the same solution in
all cases (memcpy() + le32_to_cpu()).
Tested only on a little-endian system.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180109203248.139249-2-briannorris@chromium.org
This takes care of 2 TODOs in this driver, by using the common DSI
packet-marshalling code instead of our custom short/long write code.
This both saves us some duplicated code and gets us free support for
command types that weren't already part of our switch block (e.g.,
MIPI_DSI_GENERIC_LONG_WRITE).
The code logic stays mostly intact, except that it becomes unnecessary
to split the short/long write functions, and we have to copy data a bit
more.
Along the way, I noticed that loop bounds were a little odd:
while (DIV_ROUND_UP(len, pld_data_bytes))
This really was just supposed to be 'len != 0', so I made that more
clear.
Tested on RK3399 with some pending refactoring patches by Nickey Yang,
to make the Rockchip DSI driver wrap this common driver.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180109203248.139249-1-briannorris@chromium.org
sparse complains:
drivers/gpu/drm/bridge/synopsys/dw-mipi-dsi.c:703:6: warning: symbol
'dw_mipi_dsi_bridge_mode_set' was not declared. Should it be static?
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180109203319.139520-1-briannorris@chromium.org
This extends the dumb VGA DAC bridge to handle the THS8134A
and THS8134B VGA DACs in addition to those already handled.
We assign the proper timing data to the pointer inside the
bridge struct so display controllers that need to align their
timings to the bridge can pick it up and work from there.
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180112074854.9560-3-linus.walleij@linaro.org
Sean Paul