When global vlan options are equal sequentially we compress them in a
range to save space and reduce processing time. In order to have the
proper range end id we need to update range_end if the options are equal
otherwise we get ranges with the same end vlan id as the start.
Fixes: 743a53d963 ("net: bridge: vlan: add support for dumping global vlan options")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/20210810092139.11700-1-razor@blackwall.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Embed the standard multicast router port export by br_rports_fill_info()
into a new global vlan attribute BRIDGE_VLANDB_GOPTS_MCAST_ROUTER_PORTS.
In order to have the same format for the global bridge mcast context and
the per-vlan mcast context we need a double-nesting:
- BRIDGE_VLANDB_GOPTS_MCAST_ROUTER_PORTS
- MDBA_ROUTER
Currently we don't compare router lists, if any router port exists in
the bridge mcast contexts we consider their option sets as different and
export them separately.
In addition we export the router port vlan id when dumping similar to
the router port notification format.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we are dumping the router ports of a vlan mcast context we need to
use the bridge/vlan and port/vlan's multicast contexts to check if
IPv4/IPv6 router port is present and later to dump the vlan id.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change and retrieve global vlan multicast router state
which is used for the bridge itself. We just need to pass multicast context
to br_multicast_set_router instead of bridge device and the rest of the
logic remains the same.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change and retrieve global vlan multicast querier state.
We just need to pass multicast context to br_multicast_set_querier
instead of bridge device and the rest of the logic remains the same.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a minor optimization and better behaviour to make sure querier and
query sending routines affect only the matching multicast context
depending if vlan snooping is enabled (vlan ctx vs bridge ctx).
It also avoids sending unnecessary extra query packets.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to have the querier state per multicast context in order to have
per-vlan control, so remove the internal option bit and move it to the
multicast context. Also annotate the lockless reads of the new variable.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change and retrieve global vlan multicast startup query
interval option.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change and retrieve global vlan multicast query response
interval option.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change and retrieve global vlan multicast query interval
option.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change and retrieve global vlan multicast querier interval
option.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change and retrieve global vlan multicast membership
interval option.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change and retrieve global vlan multicast last member
interval option.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change and retrieve global vlan multicast startup query
count option.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change and retrieve global vlan multicast last member
count option.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change and retrieve global vlan IGMP/MLD versions.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Use nfnetlink_unicast() instead of netlink_unicast() in nft_compat.
2) Remove call to nf_ct_l4proto_find() in flowtable offload timeout
fixup.
3) CLUSTERIP registers ARP hook on demand, from Florian.
4) Use clusterip_net to store pernet warning, also from Florian.
5) Remove struct netns_xt, from Florian Westphal.
6) Enable ebtables hooks in initns on demand, from Florian.
7) Allow to filter conntrack netlink dump per status bits,
from Florian Westphal.
8) Register x_tables hooks in initns on demand, from Florian.
9) Remove queue_handler from per-netns structure, again from Florian.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ignore fdb flags when adding port extern learn entries and always set
BR_FDB_LOCAL flag when adding bridge extern learn entries. This is
closest to the behaviour we had before and avoids breaking any use cases
which were allowed.
This patch fixes iproute2 calls which assume NUD_PERMANENT and were
allowed before, example:
$ bridge fdb add 00:11:22:33:44:55 dev swp1 extern_learn
Extern learn entries are allowed to roam, but do not expire, so static
or dynamic flags make no sense for them.
Also add a comment for future reference.
Fixes: eb100e0e24 ("net: bridge: allow to add externally learned entries from user-space")
Fixes: 0541a62932 ("net: bridge: validate the NUD_PERMANENT bit when adding an extern_learn FDB entry")
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Tested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20210810110010.43859-1-razor@blackwall.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) Restrict range element expansion in ipset to avoid soft lockup,
from Jozsef Kadlecsik.
2) Memleak in error path for nf_conntrack_bridge for IPv4 packets,
from Yajun Deng.
3) Simplify conntrack garbage collection strategy to avoid frequent
wake-ups, from Florian Westphal.
4) Fix NFNLA_HOOK_FUNCTION_NAME string, do not include module name.
5) Missing chain family netlink attribute in chain description
in nfnetlink_hook.
6) Incorrect sequence number on nfnetlink_hook dumps.
7) Use netlink request family in reply message for consistency.
8) Remove offload_pickup sysctl, use conntrack for established state
instead, from Florian Westphal.
9) Translate NFPROTO_INET/ingress to NFPROTO_NETDEV/ingress, since
NFPROTO_INET is not exposed through nfnetlink_hook.
* git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf:
netfilter: nfnetlink_hook: translate inet ingress to netdev
netfilter: conntrack: remove offload_pickup sysctl again
netfilter: nfnetlink_hook: Use same family as request message
netfilter: nfnetlink_hook: use the sequence number of the request message
netfilter: nfnetlink_hook: missing chain family
netfilter: nfnetlink_hook: strip off module name from hookfn
netfilter: conntrack: collect all entries in one cycle
netfilter: nf_conntrack_bridge: Fix memory leak when error
netfilter: ipset: Limit the maximal range of consecutive elements to add/delete
====================
Link: https://lore.kernel.org/r/20210806151149.6356-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Build failure in drivers/net/wwan/mhi_wwan_mbim.c:
add missing parameter (0, assuming we don't want buffer pre-alloc).
Conflict in drivers/net/dsa/sja1105/sja1105_main.c between:
589918df93 ("net: dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
0fac6aa098 ("net: dsa: sja1105: delete the best_effort_vlan_filtering mode")
Follow the instructions from the commit message of the former commit
- removed the if conditions. When looking at commit 589918df93 ("net:
dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
note that the mask_iotag fields get removed by the following patch.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit ad2f99aedf ("net: bridge: move bridge ioctls out of .ndo_do_ioctl")
changed the source of the argument copy in bridge's old_deviceless() from
args[1] (user ptr to device name) to uarg (ptr to ioctl arguments) causing
wrong device name to be used.
Example (broken, bridge exists but is up):
$ brctl delbr bridge
bridge bridge doesn't exist; can't delete it
Example (working):
$ brctl delbr bridge
bridge bridge is still up; can't delete it
Fixes: ad2f99aedf ("net: bridge: move bridge ioctls out of .ndo_do_ioctl")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before commit ad2f99aedf ("net: bridge: move bridge ioctls out of
.ndo_do_ioctl") the bridge ioctl calls were divided in two parts:
one was deviceless called by sock_ioctl and didn't expect rtnl to be held,
the other was with a device called by dev_ifsioc() and expected rtnl to be
held. After the commit above they were united in a single ioctl stub, but
it didn't take care of the locking expectations.
For sock_ioctl now we acquire (1) br_ioctl_mutex, (2) rtnl
and for dev_ifsioc we acquire (1) rtnl, (2) br_ioctl_mutex
The fix is to get a refcnt on the netdev for dev_ifsioc calls and drop rtnl
then to reacquire it in the bridge ioctl stub after br_ioctl_mutex has
been acquired. That will avoid playing locking games and make the rules
straight-forward: we always take br_ioctl_mutex first, and then rtnl.
Reported-by: syzbot+34fe5894623c4ab1b379@syzkaller.appspotmail.com
Fixes: ad2f99aedf ("net: bridge: move bridge ioctls out of .ndo_do_ioctl")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the introduction of explicit offloading API in switchdev in commit
2f5dc00f7a ("net: bridge: switchdev: let drivers inform which bridge
ports are offloaded"), we started having Ethernet switch drivers calling
directly into a function exported by net/bridge/br_switchdev.c, which is
a function exported by the bridge driver.
This means that drivers that did not have an explicit dependency on the
bridge before, like cpsw and am65-cpsw, now do - otherwise it is not
possible to call a symbol exported by a driver that can be built as
module unless you are a module too.
There was an attempt to solve the dependency issue in the form of commit
b0e8181762 ("net: build all switchdev drivers as modules when the
bridge is a module"). Grygorii Strashko, however, says about it:
| In my opinion, the problem is a bit bigger here than just fixing the
| build :(
|
| In case, of ^cpsw the switchdev mode is kinda optional and in many
| cases (especially for testing purposes, NFS) the multi-mac mode is
| still preferable mode.
|
| There were no such tight dependency between switchdev drivers and
| bridge core before and switchdev serviced as independent, notification
| based layer between them, so ^cpsw still can be "Y" and bridge can be
| "M". Now for mostly every kernel build configuration the CONFIG_BRIDGE
| will need to be set as "Y", or we will have to update drivers to
| support build with BRIDGE=n and maintain separate builds for
| networking vs non-networking testing. But is this enough? Wouldn't
| it cause 'chain reaction' required to add more and more "Y" options
| (like CONFIG_VLAN_8021Q)?
|
| PS. Just to be sure we on the same page - ARM builds will be forced
| (with this patch) to have CONFIG_TI_CPSW_SWITCHDEV=m and so all our
| automation testing will just fail with omap2plus_defconfig.
In the light of this, it would be desirable for some configurations to
avoid dependencies between switchdev drivers and the bridge, and have
the switchdev mode as completely optional within the driver.
Arnd Bergmann also tried to write a patch which better expressed the
build time dependency for Ethernet switch drivers where the switchdev
support is optional, like cpsw/am65-cpsw, and this made the drivers
follow the bridge (compile as module if the bridge is a module) only if
the optional switchdev support in the driver was enabled in the first
place:
https://patchwork.kernel.org/project/netdevbpf/patch/20210802144813.1152762-1-arnd@kernel.org/
but this still did not solve the fact that cpsw and am65-cpsw now must
be built as modules when the bridge is a module - it just expressed
correctly that optional dependency. But the new behavior is an apparent
regression from Grygorii's perspective.
So to support the use case where the Ethernet driver is built-in,
NET_SWITCHDEV (a bool option) is enabled, and the bridge is a module, we
need a framework that can handle the possible absence of the bridge from
the running system, i.e. runtime bloatware as opposed to build-time
bloatware.
Luckily we already have this framework, since switchdev has been using
it extensively. Events from the bridge side are transmitted to the
driver side using notifier chains - this was originally done so that
unrelated drivers could snoop for events emitted by the bridge towards
ports that are implemented by other drivers (think of a switch driver
with LAG offload that listens for switchdev events on a bonding/team
interface that it offloads).
There are also events which are transmitted from the driver side to the
bridge side, which again are modeled using notifiers.
SWITCHDEV_FDB_ADD_TO_BRIDGE is an example of this, and deals with
notifying the bridge that a MAC address has been dynamically learned.
So there is a precedent we can use for modeling the new framework.
The difference compared to SWITCHDEV_FDB_ADD_TO_BRIDGE is that the work
that the bridge needs to do when a port becomes offloaded is blocking in
its nature: replay VLANs, MDBs etc. The calling context is indeed
blocking (we are under rtnl_mutex), but the existing switchdev
notification chain that the bridge is subscribed to is only the atomic
one. So we need to subscribe the bridge to the blocking switchdev
notification chain too.
This patch:
- keeps the driver-side perception of the switchdev_bridge_port_{,un}offload
unchanged
- moves the implementation of switchdev_bridge_port_{,un}offload from
the bridge module into the switchdev module.
- makes everybody that is subscribed to the switchdev blocking notifier
chain "hear" offload & unoffload events
- makes the bridge driver subscribe and handle those events
- moves the bridge driver's handling of those events into 2 new
functions called br_switchdev_port_{,un}offload. These functions
contain in fact the core of the logic that was previously in
switchdev_bridge_port_{,un}offload, just that now we go through an
extra indirection layer to reach them.
Unlike all the other switchdev notification structures, the structure
used to carry the bridge port information, struct
switchdev_notifier_brport_info, does not contain a "bool handled".
This is because in the current usage pattern, we always know that a
switchdev bridge port offloading event will be handled by the bridge,
because the switchdev_bridge_port_offload() call was initiated by a
NETDEV_CHANGEUPPER event in the first place, where info->upper_dev is a
bridge. So if the bridge wasn't loaded, then the CHANGEUPPER event
couldn't have happened.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It should be added kfree_skb_list() when err is not equal to zero
in nf_br_ip_fragment().
v2: keep this aligned with IPv6.
v3: modify iter.frag_list to iter.frag.
Fixes: 3c171f496e ("netfilter: bridge: add connection tracking system")
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Nikolay points out that it is incorrect to assume that it is impossible
to have an fdb entry with fdb->dst == NULL and the BR_FDB_LOCAL bit in
fdb->flags not set. This is because there are reader-side places that
test_bit(BR_FDB_LOCAL, &fdb->flags) without the br->hash_lock, and if
the updating of the FDB entry happens on another CPU, there are no
memory barriers at writer or reader side which would ensure that the
reader sees the updates to both fdb->flags and fdb->dst in the same
order, i.e. the reader will not see an inconsistent FDB entry.
So we must be prepared to deal with FDB entries where fdb->dst and
fdb->flags are in a potentially inconsistent state, and that means that
fdb->dst == NULL should remain a condition to pick the net_device that
we report to switchdev as being the bridge device, which is what the
code did prior to the blamed patch.
Fixes: 52e4bec155 ("net: bridge: switchdev: treat local FDBs the same as entries towards the bridge")
Suggested-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/20210802113633.189831-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently it is possible to add broken extern_learn FDB entries to the
bridge in two ways:
1. Entries pointing towards the bridge device that are not local/permanent:
ip link add br0 type bridge
bridge fdb add 00:01:02:03:04:05 dev br0 self extern_learn static
2. Entries pointing towards the bridge device or towards a port that
are marked as local/permanent, however the bridge does not process the
'permanent' bit in any way, therefore they are recorded as though they
aren't permanent:
ip link add br0 type bridge
bridge fdb add 00:01:02:03:04:05 dev br0 self extern_learn permanent
Since commit 52e4bec155 ("net: bridge: switchdev: treat local FDBs the
same as entries towards the bridge"), these incorrect FDB entries can
even trigger NULL pointer dereferences inside the kernel.
This is because that commit made the assumption that all FDB entries
that are not local/permanent have a valid destination port. For context,
local / permanent FDB entries either have fdb->dst == NULL, and these
point towards the bridge device and are therefore local and not to be
used for forwarding, or have fdb->dst == a net_bridge_port structure
(but are to be treated in the same way, i.e. not for forwarding).
That assumption _is_ correct as long as things are working correctly in
the bridge driver, i.e. we cannot logically have fdb->dst == NULL under
any circumstance for FDB entries that are not local. However, the
extern_learn code path where FDB entries are managed by a user space
controller show that it is possible for the bridge kernel driver to
misinterpret the NUD flags of an entry transmitted by user space, and
end up having fdb->dst == NULL while not being a local entry. This is
invalid and should be rejected.
Before, the two commands listed above both crashed the kernel in this
check from br_switchdev_fdb_notify:
struct net_device *dev = info.is_local ? br->dev : dst->dev;
info.is_local == false, dst == NULL.
After this patch, the invalid entry added by the first command is
rejected:
ip link add br0 type bridge && bridge fdb add 00:01:02:03:04:05 dev br0 self extern_learn static; ip link del br0
Error: bridge: FDB entry towards bridge must be permanent.
and the valid entry added by the second command is properly treated as a
local address and does not crash br_switchdev_fdb_notify anymore:
ip link add br0 type bridge && bridge fdb add 00:01:02:03:04:05 dev br0 self extern_learn permanent; ip link del br0
Fixes: eb100e0e24 ("net: bridge: allow to add externally learned entries from user-space")
Reported-by: syzbot+9ba1174359adba5a5b7c@syzkaller.appspotmail.com
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/20210801231730.7493-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If any of these modules is loaded, hooks get registered in all netns:
Before: 'unshare -n nft list hooks' shows:
family bridge hook prerouting {
-2147483648 ebt_broute
-0000000300 ebt_nat_hook
}
family bridge hook input {
-0000000200 ebt_filter_hook
}
family bridge hook forward {
-0000000200 ebt_filter_hook
}
family bridge hook output {
+0000000100 ebt_nat_hook
+0000000200 ebt_filter_hook
}
family bridge hook postrouting {
+0000000300 ebt_nat_hook
}
This adds 'template 'tables' for ebtables.
Each ebtable_foo registers the table as a template, with an init function
that gets called once the first get/setsockopt call is made.
ebtables core then searches the (per netns) list of tables.
If no table is found, it searches the list of templates instead.
If a template entry exists, the init function is called which will
enable the table and register the hooks (so packets are diverted
to the table).
If no entry is found in the template list, request_module is called.
After this, hook registration is delayed until the 'ebtables'
(set/getsockopt) request is made for a given table and will only
happen in the specific namespace.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently the following script:
1. ip link add br0 type bridge vlan_filtering 1 && ip link set br0 up
2. ip link set swp2 up && ip link set swp2 master br0
3. ip link set swp3 up && ip link set swp3 master br0
4. ip link set swp4 up && ip link set swp4 master br0
5. bridge vlan del dev swp2 vid 1
6. bridge vlan del dev swp3 vid 1
7. ip link set swp4 nomaster
8. ip link set swp3 nomaster
produces the following output:
[ 641.010738] sja1105 spi0.1: port 2 failed to delete 00:1f:7b:63:02:48 vid 1 from fdb: -2
[ swp2, swp3 and br0 all have the same MAC address, the one listed above ]
In short, this happens because the number of FDB entry additions
notified to switchdev is unbalanced with the number of deletions.
At step 1, the bridge has a random MAC address. At step 2, the
br_fdb_replay of swp2 receives this initial MAC address. Then the bridge
inherits the MAC address of swp2 via br_fdb_change_mac_address(), and it
notifies switchdev (only swp2 at this point) of the deletion of the
random MAC address and the addition of 00:1f:7b:63:02:48 as a local FDB
entry with fdb->dst == swp2, in VLANs 0 and the default_pvid (1).
During step 7:
del_nbp
-> br_fdb_delete_by_port(br, p, vid=0, do_all=1);
-> fdb_delete_local(br, p, f);
br_fdb_delete_by_port() deletes all entries towards the ports,
regardless of vid, because do_all is 1.
fdb_delete_local() has logic to migrate local FDB entries deleted from
one port to another port which shares the same MAC address and is in the
same VLAN, or to the bridge device itself. This migration happens
without notifying switchdev of the deletion on the old port and the
addition on the new one, just fdb->dst is changed and the added_by_user
flag is cleared.
In the example above, the del_nbp(swp4) causes the
"addr 00:1f:7b:63:02:48 vid 1" local FDB entry with fdb->dst == swp4
that existed up until then to be migrated directly towards the bridge
(fdb->dst == NULL). This is because it cannot be migrated to any of the
other ports (swp2 and swp3 are not in VLAN 1).
After the migration to br0 takes place, swp4 requests a deletion replay
of all FDB entries. Since the "addr 00:1f:7b:63:02:48 vid 1" entry now
point towards the bridge, a deletion of it is replayed. There was just
a prior addition of this address, so the switchdev driver deletes this
entry.
Then, the del_nbp(swp3) at step 8 triggers another br_fdb_replay, and
switchdev is notified again to delete "addr 00:1f:7b:63:02:48 vid 1".
But it can't because it no longer has it, so it returns -ENOENT.
There are other possibilities to trigger this issue, but this is by far
the simplest to explain.
To fix this, we must avoid the situation where the addition of an FDB
entry is notified to switchdev as a local entry on a port, and the
deletion is notified on the bridge itself.
Considering that the 2 types of FDB entries are completely equivalent
and we cannot have the same MAC address as a local entry on 2 bridge
ports, or on a bridge port and pointing towards the bridge at the same
time, it makes sense to hide away from switchdev completely the fact
that a local FDB entry is associated with a given bridge port at all.
Just say that it points towards the bridge, it should make no difference
whatsoever to the switchdev driver and should even lead to a simpler
overall implementation, will less cases to handle.
This also avoids any modification at all to the core bridge driver, just
what is reported to switchdev changes. With the local/permanent entries
on bridge ports being already reported to user space, it is hard to
believe that the bridge behavior can change in any backwards-incompatible
way such as making all local FDB entries point towards the bridge.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when a switchdev port joins a bridge, we replay all FDB
entries pointing towards that port or towards the bridge.
However, this is insufficient in certain situations:
(a) DSA, through its assisted_learning_on_cpu_port logic, snoops
dynamically learned FDB entries on foreign interfaces.
These are FDB entries that are pointing neither towards the newly
joined switchdev port, nor towards the bridge. So these addresses
would be missed when joining a bridge where a foreign interface has
already learned some addresses, and they would also linger on if the
DSA port leaves the bridge before the foreign interface forgets them.
None of this happens if we replay the entire FDB when the port joins.
(b) There is a desire to treat local FDB entries on a port (i.e. the
port's termination MAC address) identically to FDB entries pointing
towards the bridge itself. More details on the reason behind this in
the next patch. The point is that this cannot be done given the
current structure of br_fdb_replay() in this situation:
ip link set swp0 master br0 # br0 inherits its MAC address from swp0
ip link set swp1 master br0
What is desirable is that when swp1 joins the bridge, br_fdb_replay()
also notifies swp1 of br0's MAC address, but this won't in fact
happen because the MAC address of br0 does not have fdb->dst == NULL
(it doesn't point towards the bridge), but it has fdb->dst == swp0.
So our current logic makes it impossible for that address to be
replayed. But if we dump the entire FDB instead of just the entries
with fdb->dst == swp1 and fdb->dst == NULL, then the inherited MAC
address of br0 will be replayed too, which is what we need.
A natural question arises: say there is an FDB entry to be replayed,
like a MAC address dynamically learned on a foreign interface that
belongs to a bridge where no switchdev port has joined yet. If 10
switchdev ports belonging to the same driver join this bridge, one by
one, won't every port get notified 10 times of the foreign FDB entry,
amounting to a total of 100 notifications for this FDB entry in the
switchdev driver?
Well, yes, but this is where the "void *ctx" argument for br_fdb_replay
is useful: every port of the switchdev driver is notified whenever any
other port requests an FDB replay, but because the replay was initiated
by a different port, its context is different from the initiating port's
context, so it ignores those replays.
So the foreign FDB entry will be installed only 10 times, once per port.
This is done so that the following 4 code paths are always well balanced:
(a) addition of foreign FDB entry is replayed when port joins bridge
(b) deletion of foreign FDB entry is replayed when port leaves bridge
(c) addition of foreign FDB entry is notified to all ports currently in bridge
(c) deletion of foreign FDB entry is notified to all ports currently in bridge
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Working towards obsoleting the .ndo_do_ioctl operation entirely,
stop passing the SIOCBRADDIF/SIOCBRDELIF device ioctl commands
into this callback.
My first attempt was to add another ndo_siocbr() callback, but
as there is only a single driver that takes these commands and
there is already a hook mechanism to call directly into this
driver, extend this hook instead, and use it for both the
deviceless and the device specific ioctl commands.
Cc: Roopa Prabhu <roopa@nvidia.com>
Cc: Nikolay Aleksandrov <nikolay@nvidia.com>
Cc: bridge@lists.linux-foundation.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge driver has an old set of ioctls using the SIOCDEVPRIVATE
namespace that have never worked in compat mode and are explicitly
forbidden already.
Move them over to ndo_siocdevprivate and fix compat mode for these,
because we can.
Cc: Roopa Prabhu <roopa@nvidia.com>
Cc: Nikolay Aleksandrov <nikolay@nvidia.com>
Cc: bridge@lists.linux-foundation.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a brother of br_vlan_get_info() which is protected by the RCU
mechanism, as opposed to br_vlan_get_info() which relies on taking the
write-side rtnl_mutex.
This is needed for drivers which need to find out whether a bridge port
has a VLAN configured or not. For example, certain DSA switches might
not offer complete source port identification to the CPU on RX, just the
VLAN in which the packet was received. Based on this VLAN, we cannot set
an accurate skb->dev ingress port, but at least we can configure one
that behaves the same as the correct one would (this is possible because
DSA sets skb->offload_fwd_mark = 1).
When we look at the bridge RX handler (br_handle_frame), we see that
what matters regarding skb->dev is the VLAN ID and the port STP state.
So we need to select an skb->dev that has the same bridge VLAN as the
packet we're receiving, and is in the LEARNING or FORWARDING STP state.
The latter is easy, but for the former, we should somehow keep a shadow
list of the bridge VLANs on each port, and a lookup table between VLAN
ID and the 'designated port for imprecise RX'. That is rather
complicated to keep in sync properly (the designated port per VLAN needs
to be updated on the addition and removal of a VLAN, as well as on the
join/leave events of the bridge on that port).
So, to avoid all that complexity, let's just iterate through our finite
number of ports and ask the bridge, for each packet: "do you have this
VLAN configured on this port?".
Cc: Roopa Prabhu <roopa@nvidia.com>
Cc: Nikolay Aleksandrov <nikolay@nvidia.com>
Cc: Ido Schimmel <idosch@nvidia.com>
Cc: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING is notified by the bridge from
two places:
- nbp_vlan_init(), during bridge port creation
- br_vlan_filter_toggle(), during a netlink/sysfs/ioctl change requested
by user space
If a switchdev driver uses br_vlan_enabled(br_dev) inside its handler
for the SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING attribute notifier,
different things will be seen depending on whether the bridge calls from
the first path or the second:
- in nbp_vlan_init(), br_vlan_enabled() reflects the current state of
the bridge
- in br_vlan_filter_toggle(), br_vlan_enabled() reflects the past state
of the bridge
This can lead in some cases to complications in driver implementation,
which can be avoided if these could reliably use br_vlan_enabled().
Nothing seems to depend on this behavior, and it seems overall more
straightforward for br_vlan_enabled() to return the proper value even
during the SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING notifier, so
temporarily enable the bridge option, then revert it if the switchdev
notifier failed.
Cc: Roopa Prabhu <roopa@nvidia.com>
Cc: Nikolay Aleksandrov <nikolay@nvidia.com>
Cc: Ido Schimmel <idosch@nvidia.com>
Cc: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switchdev support can be disabled at compile time, and in that case,
struct sk_buff will not contain the offload_fwd_mark field.
To make the code in br_forward.c work in both cases, we do what is done
in other places and we create a helper function, with an empty shim
definition, that is implemented by the br_switchdev.o translation module.
This is always compiled if and only if CONFIG_NET_SWITCHDEV is y or m.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 472111920f ("net: bridge: switchdev: allow the TX data plane forwarding to be offloaded")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow switchdevs to forward frames from the CPU in accordance with the
bridge configuration in the same way as is done between bridge
ports. This means that the bridge will only send a single skb towards
one of the ports under the switchdev's control, and expects the driver
to deliver the packet to all eligible ports in its domain.
Primarily this improves the performance of multicast flows with
multiple subscribers, as it allows the hardware to perform the frame
replication.
The basic flow between the driver and the bridge is as follows:
- When joining a bridge port, the switchdev driver calls
switchdev_bridge_port_offload() with tx_fwd_offload = true.
- The bridge sends offloadable skbs to one of the ports under the
switchdev's control using skb->offload_fwd_mark = true.
- The switchdev driver checks the skb->offload_fwd_mark field and lets
its FDB lookup select the destination port mask for this packet.
v1->v2:
- convert br_input_skb_cb::fwd_hwdoms to a plain unsigned long
- introduce a static key "br_switchdev_fwd_offload_used" to minimize the
impact of the newly introduced feature on all the setups which don't
have hardware that can make use of it
- introduce a check for nbp->flags & BR_FWD_OFFLOAD to optimize cache
line access
- reorder nbp_switchdev_frame_mark_accel() and br_handle_vlan() in
__br_forward()
- do not strip VLAN on egress if forwarding offload on VLAN-aware bridge
is being used
- propagate errors from .ndo_dfwd_add_station() if not EOPNOTSUPP
v2->v3:
- replace the solution based on .ndo_dfwd_add_station with a solution
based on switchdev_bridge_port_offload
- rename BR_FWD_OFFLOAD to BR_TX_FWD_OFFLOAD
v3->v4: rebase
v4->v5:
- make sure the static key is decremented on bridge port unoffload
- more function and variable renaming and comments for them:
br_switchdev_fwd_offload_used to br_switchdev_tx_fwd_offload
br_switchdev_accels_skb to br_switchdev_frame_uses_tx_fwd_offload
nbp_switchdev_frame_mark_tx_fwd to nbp_switchdev_frame_mark_tx_fwd_to_hwdom
nbp_switchdev_frame_mark_accel to nbp_switchdev_frame_mark_tx_fwd_offload
fwd_accel to tx_fwd_offload
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with commit 4f2673b3a2 ("net: bridge: add helper to replay
port and host-joined mdb entries"), DSA has introduced some bridge
helpers that replay switchdev events (FDB/MDB/VLAN additions and
deletions) that can be lost by the switchdev drivers in a variety of
circumstances:
- an IP multicast group was host-joined on the bridge itself before any
switchdev port joined the bridge, leading to the host MDB entries
missing in the hardware database.
- during the bridge creation process, the MAC address of the bridge was
added to the FDB as an entry pointing towards the bridge device
itself, but with no switchdev ports being part of the bridge yet, this
local FDB entry would remain unknown to the switchdev hardware
database.
- a VLAN/FDB/MDB was added to a bridge port that is a LAG interface,
before any switchdev port joined that LAG, leading to the hardware
database missing those entries.
- a switchdev port left a LAG that is a bridge port, while the LAG
remained part of the bridge, and all FDB/MDB/VLAN entries remained
installed in the hardware database of the switchdev port.
Also, since commit 0d2cfbd41c ("net: bridge: ignore switchdev events
for LAG ports which didn't request replay"), DSA introduced a method,
based on a const void *ctx, to ensure that two switchdev ports under the
same LAG that is a bridge port do not see the same MDB/VLAN entry being
replayed twice by the bridge, once for every bridge port that joins the
LAG.
With so many ordering corner cases being possible, it seems unreasonable
to expect a switchdev driver writer to get it right from the first try.
Therefore, now that DSA has experimented with the bridge replay helpers
for a little bit, we can move the code to the bridge driver where it is
more readily available to all switchdev drivers.
To convert the switchdev object replay helpers from "pull mode" (where
the driver asks for them) to a "push mode" (where the bridge offers them
automatically), the biggest problem is that the bridge needs to be aware
when a switchdev port joins and leaves, even when the switchdev is only
indirectly a bridge port (for example when the bridge port is a LAG
upper of the switchdev).
Luckily, we already have a hook for that, in the form of the newly
introduced switchdev_bridge_port_offload() and
switchdev_bridge_port_unoffload() calls. These offer a natural place for
hooking the object addition and deletion replays.
Extend the above 2 functions with:
- pointers to the switchdev atomic notifier (for FDB replays) and the
blocking notifier (for MDB and VLAN replays).
- the "const void *ctx" argument required for drivers to be able to
disambiguate between which port is targeted, when multiple ports are
lowers of the same LAG that is a bridge port. Most of the drivers pass
NULL to this argument, except the ones that support LAG offload and have
the proper context check already in place in the switchdev blocking
notifier handler.
Also unexport the replay helpers, since nobody except the bridge calls
them directly now.
Note that:
(a) we abuse the terminology slightly, because FDB entries are not
"switchdev objects", but we count them as objects nonetheless.
With no direct way to prove it, I think they are not modeled as
switchdev objects because those can only be installed by the bridge
to the hardware (as opposed to FDB entries which can be propagated
in the other direction too). This is merely an abuse of terms, FDB
entries are replayed too, despite not being objects.
(b) the bridge does not attempt to sync port attributes to newly joined
ports, just the countable stuff (the objects). The reason for this
is simple: no universal and symmetric way to sync and unsync them is
known. For example, VLAN filtering: what to do on unsync, disable or
leave it enabled? Similarly, STP state, ageing timer, etc etc. What
a switchdev port does when it becomes standalone again is not really
up to the bridge's competence, and the driver should deal with it.
On the other hand, replaying deletions of switchdev objects can be
seen a matter of cleanup and therefore be treated by the bridge,
hence this patch.
We make the replay helpers opt-in for drivers, because they might not
bring immediate benefits for them:
- nbp_vlan_init() is called _after_ netdev_master_upper_dev_link(),
so br_vlan_replay() should not do anything for the new drivers on
which we call it. The existing drivers where there was even a slight
possibility for there to exist a VLAN on a bridge port before they
join it are already guarded against this: mlxsw and prestera deny
joining LAG interfaces that are members of a bridge.
- br_fdb_replay() should now notify of local FDB entries, but I patched
all drivers except DSA to ignore these new entries in commit
2c4eca3ef7 ("net: bridge: switchdev: include local flag in FDB
notifications"). Driver authors can lift this restriction as they
wish, and when they do, they can also opt into the FDB replay
functionality.
- br_mdb_replay() should fix a real issue which is described in commit
4f2673b3a2 ("net: bridge: add helper to replay port and host-joined
mdb entries"). However most drivers do not offload the
SWITCHDEV_OBJ_ID_HOST_MDB to see this issue: only cpsw and am65_cpsw
offload this switchdev object, and I don't completely understand the
way in which they offload this switchdev object anyway. So I'll leave
it up to these drivers' respective maintainers to opt into
br_mdb_replay().
So most of the drivers pass NULL notifier blocks for the replay helpers,
except:
- dpaa2-switch which was already acked/regression-tested with the
helpers enabled (and there isn't much of a downside in having them)
- ocelot which already had replay logic in "pull" mode
- DSA which already had replay logic in "pull" mode
An important observation is that the drivers which don't currently
request bridge event replays don't even have the
switchdev_bridge_port_{offload,unoffload} calls placed in proper places
right now. This was done to avoid unnecessary rework for drivers which
might never even add support for this. For driver writers who wish to
add replay support, this can be used as a tentative placement guide:
https://patchwork.kernel.org/project/netdevbpf/patch/20210720134655.892334-11-vladimir.oltean@nxp.com/
Cc: Vadym Kochan <vkochan@marvell.com>
Cc: Taras Chornyi <tchornyi@marvell.com>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a desire to make the object and FDB replay helpers optional
when moving them inside the bridge driver. For example a certain driver
might not offload host MDBs and there is no case where the replay
helpers would be of immediate use to it.
So it would be nice if we could allow drivers to pass NULL pointers for
the atomic and blocking notifier blocks, and the replay helpers to do
nothing in that case.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On reception of an skb, the bridge checks if it was marked as 'already
forwarded in hardware' (checks if skb->offload_fwd_mark == 1), and if it
is, it assigns the source hardware domain of that skb based on the
hardware domain of the ingress port. Then during forwarding, it enforces
that the egress port must have a different hardware domain than the
ingress one (this is done in nbp_switchdev_allowed_egress).
Non-switchdev drivers don't report any physical switch id (neither
through devlink nor .ndo_get_port_parent_id), therefore the bridge
assigns them a hardware domain of 0, and packets coming from them will
always have skb->offload_fwd_mark = 0. So there aren't any restrictions.
Problems appear due to the fact that DSA would like to perform software
fallback for bonding and team interfaces that the physical switch cannot
offload.
+-- br0 ---+
/ / | \
/ / | \
/ | | bond0
/ | | / \
swp0 swp1 swp2 swp3 swp4
There, it is desirable that the presence of swp3 and swp4 under a
non-offloaded LAG does not preclude us from doing hardware bridging
beteen swp0, swp1 and swp2. The bandwidth of the CPU is often times high
enough that software bridging between {swp0,swp1,swp2} and bond0 is not
impractical.
But this creates an impossible paradox given the current way in which
port hardware domains are assigned. When the driver receives a packet
from swp0 (say, due to flooding), it must set skb->offload_fwd_mark to
something.
- If we set it to 0, then the bridge will forward it towards swp1, swp2
and bond0. But the switch has already forwarded it towards swp1 and
swp2 (not to bond0, remember, that isn't offloaded, so as far as the
switch is concerned, ports swp3 and swp4 are not looking up the FDB,
and the entire bond0 is a destination that is strictly behind the
CPU). But we don't want duplicated traffic towards swp1 and swp2, so
it's not ok to set skb->offload_fwd_mark = 0.
- If we set it to 1, then the bridge will not forward the skb towards
the ports with the same switchdev mark, i.e. not to swp1, swp2 and
bond0. Towards swp1 and swp2 that's ok, but towards bond0? It should
have forwarded the skb there.
So the real issue is that bond0 will be assigned the same hardware
domain as {swp0,swp1,swp2}, because the function that assigns hardware
domains to bridge ports, nbp_switchdev_add(), recurses through bond0's
lower interfaces until it finds something that implements devlink (calls
dev_get_port_parent_id with bool recurse = true). This is a problem
because the fact that bond0 can be offloaded by swp3 and swp4 in our
example is merely an assumption.
A solution is to give the bridge explicit hints as to what hardware
domain it should use for each port.
Currently, the bridging offload is very 'silent': a driver registers a
netdevice notifier, which is put on the netns's notifier chain, and
which sniffs around for NETDEV_CHANGEUPPER events where the upper is a
bridge, and the lower is an interface it knows about (one registered by
this driver, normally). Then, from within that notifier, it does a bunch
of stuff behind the bridge's back, without the bridge necessarily
knowing that there's somebody offloading that port. It looks like this:
ip link set swp0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v
call_netdevice_notifiers
|
v
dsa_slave_netdevice_event
|
v
oh, hey! it's for me!
|
v
.port_bridge_join
What we do to solve the conundrum is to be less silent, and change the
switchdev drivers to present themselves to the bridge. Something like this:
ip link set swp0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge: Aye! I'll use this
call_netdevice_notifiers ^ ppid as the
| | hardware domain for
v | this port, and zero
dsa_slave_netdevice_event | if I got nothing.
| |
v |
oh, hey! it's for me! |
| |
v |
.port_bridge_join |
| |
+------------------------+
switchdev_bridge_port_offload(swp0, swp0)
Then stacked interfaces (like bond0 on top of swp3/swp4) would be
treated differently in DSA, depending on whether we can or cannot
offload them.
The offload case:
ip link set bond0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge: Aye! I'll use this
call_netdevice_notifiers ^ ppid as the
| | switchdev mark for
v | bond0.
dsa_slave_netdevice_event | Coincidentally (or not),
| | bond0 and swp0, swp1, swp2
v | all have the same switchdev
hmm, it's not quite for me, | mark now, since the ASIC
but my driver has already | is able to forward towards
called .port_lag_join | all these ports in hw.
for it, because I have |
a port with dp->lag_dev == bond0. |
| |
v |
.port_bridge_join |
for swp3 and swp4 |
| |
+------------------------+
switchdev_bridge_port_offload(bond0, swp3)
switchdev_bridge_port_offload(bond0, swp4)
And the non-offload case:
ip link set bond0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge waiting:
call_netdevice_notifiers ^ huh, switchdev_bridge_port_offload
| | wasn't called, okay, I'll use a
v | hwdom of zero for this one.
dsa_slave_netdevice_event : Then packets received on swp0 will
| : not be software-forwarded towards
v : swp1, but they will towards bond0.
it's not for me, but
bond0 is an upper of swp3
and swp4, but their dp->lag_dev
is NULL because they couldn't
offload it.
Basically we can draw the conclusion that the lowers of a bridge port
can come and go, so depending on the configuration of lowers for a
bridge port, it can dynamically toggle between offloaded and unoffloaded.
Therefore, we need an equivalent switchdev_bridge_port_unoffload too.
This patch changes the way any switchdev driver interacts with the
bridge. From now on, everybody needs to call switchdev_bridge_port_offload
and switchdev_bridge_port_unoffload, otherwise the bridge will treat the
port as non-offloaded and allow software flooding to other ports from
the same ASIC.
Note that these functions lay the ground for a more complex handshake
between switchdev drivers and the bridge in the future.
For drivers that will request a replay of the switchdev objects when
they offload and unoffload a bridge port (DSA, dpaa2-switch, ocelot), we
place the call to switchdev_bridge_port_unoffload() strategically inside
the NETDEV_PRECHANGEUPPER notifier's code path, and not inside
NETDEV_CHANGEUPPER. This is because the switchdev object replay helpers
need the netdev adjacency lists to be valid, and that is only true in
NETDEV_PRECHANGEUPPER.
Cc: Vadym Kochan <vkochan@marvell.com>
Cc: Taras Chornyi <tchornyi@marvell.com>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch: regression
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> # ocelot-switch
Signed-off-by: David S. Miller <davem@davemloft.net>
Since hwdoms have only been used thus far for equality comparisons, the
bridge has used the simplest possible assignment policy; using a
counter to keep track of the last value handed out.
With the upcoming transmit offloading, we need to perform set
operations efficiently based on hwdoms, e.g. we want to answer
questions like "has this skb been forwarded to any port within this
hwdom?"
Move to a bitmap-based allocation scheme that recycles hwdoms once all
members leaves the bridge. This means that we can use a single
unsigned long to keep track of the hwdoms that have received an skb.
v1->v2: convert the typedef DECLARE_BITMAP(br_hwdom_map_t, BR_HWDOM_MAX)
into a plain unsigned long.
v2->v6: none
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change, four related - but distinct - concepts where named
offload_fwd_mark:
- skb->offload_fwd_mark: Set by the switchdev driver if the underlying
hardware has already forwarded this frame to the other ports in the
same hardware domain.
- nbp->offload_fwd_mark: An idetifier used to group ports that share
the same hardware forwarding domain.
- br->offload_fwd_mark: Counter used to make sure that unique IDs are
used in cases where a bridge contains ports from multiple hardware
domains.
- skb->cb->offload_fwd_mark: The hardware domain on which the frame
ingressed and was forwarded.
Introduce the term "hardware forwarding domain" ("hwdom") in the
bridge to denote a set of ports with the following property:
If an skb with skb->offload_fwd_mark set, is received on a port
belonging to hwdom N, that frame has already been forwarded to all
other ports in hwdom N.
By decoupling the name from "offload_fwd_mark", we can extend the
term's definition in the future - e.g. to add constraints that
describe expected egress behavior - without overloading the meaning of
"offload_fwd_mark".
- nbp->offload_fwd_mark thus becomes nbp->hwdom.
- br->offload_fwd_mark becomes br->last_hwdom.
- skb->cb->offload_fwd_mark becomes skb->cb->src_hwdom. The slight
change in naming here mandates a slight change in behavior of the
nbp_switchdev_frame_mark() function. Previously, it only set this
value in skb->cb for packets with skb->offload_fwd_mark true (ones
which were forwarded in hardware). Whereas now we always track the
incoming hwdom for all packets coming from a switchdev (even for the
packets which weren't forwarded in hardware, such as STP BPDUs, IGMP
reports etc). As all uses of skb->cb->offload_fwd_mark were already
gated behind checks of skb->offload_fwd_mark, this will not introduce
any functional change, but it paves the way for future changes where
the ingressing hwdom must be known for frames coming from a switchdev
regardless of whether they were forwarded in hardware or not
(basically, if the skb comes from a switchdev, skb->cb->src_hwdom now
always tracks which one).
A typical example where this is relevant: the switchdev has a fixed
configuration to trap STP BPDUs, but STP is not running on the bridge
and the group_fwd_mask allows them to be forwarded. Say we have this
setup:
br0
/ | \
/ | \
swp0 swp1 swp2
A BPDU comes in on swp0 and is trapped to the CPU; the driver does not
set skb->offload_fwd_mark. The bridge determines that the frame should
be forwarded to swp{1,2}. It is imperative that forward offloading is
_not_ allowed in this case, as the source hwdom is already "poisoned".
Recording the source hwdom allows this case to be handled properly.
v2->v3: added code comments
v3->v6: none
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding bridge multicast context support for host-joined groups is easy
because we only need the proper timer value. We pass the already chosen
context and use its timer value.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Choose the proper bridge multicast context when user-spaces is adding
mdb entries. Currently we require the vlan to be configured on at least
one device (port or bridge) in order to add an mdb entry if vlan
mcast snooping is enabled (vlan snooping implies vlan filtering).
Note that we always allow deleting an entry, regardless of the vlan state.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the recent change to use bridge/port multicast context pointers
instead of bridge/port I missed to convert two locations which pass the
port pointer as-is, but with the new model we need to verify the port
context is non-NULL first and retrieve the port from it. The first
location is when doing querier selection when a query is received, the
second location is when leaving a group. The port context will be null
if the packets originated from the bridge device (i.e. from the host).
The fix is simple just check if the port context exists and retrieve
the port pointer from it.
Fixes: adc47037a7 ("net: bridge: multicast: use multicast contexts instead of bridge or port")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new global vlan option which controls whether multicast snooping
is enabled or disabled for a single vlan. It controls the vlan private
flag: BR_VLFLAG_GLOBAL_MCAST_ENABLED.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for global options notifications. They use only RTM_NEWVLAN
since global options can only be set and are contained in a separate
vlan global options attribute. Notifications are compressed in ranges
where possible, i.e. the sequential vlan options are equal.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new vlan options dump flag which causes only global vlan options
to be dumped. The dumps are done only with bridge devices, ports are
ignored. They support vlan compression if the options in sequential
vlans are equal (currently always true).
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can have two types of vlan options depending on context:
- per-device vlan options (split in per-bridge and per-port)
- global vlan options
The second type wasn't supported in the bridge until now, but we need
them for per-vlan multicast support, per-vlan STP support and other
options which require global vlan context. They are contained in the global
bridge vlan context even if the vlan is not configured on the bridge device
itself. This patch adds initial netlink attributes and support for setting
these global vlan options, they can only be set (RTM_NEWVLAN) and the
operation must use the bridge device. Since there are no such options yet
it shouldn't have any functional effect.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the port multicast context to check if the router port is a vlan and
in case it is include its vlan id in the notification.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic vlan context querier support, if the contexts passed to
multicast_alloc_query are vlan then the query will be tagged. Also
handle querier start/stop of vlan contexts.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers which check if the current bridge/port multicast context
should be used (i.e. they're not disabled) and use them for Rx IGMP/MLD
processing, timers and new group addition. It is important for vlans to
disable processing of timer/packet after the multicast_lock is obtained
if the vlan context doesn't have BR_VLFLAG_MCAST_ENABLED. There are two
cases when that flag is missing:
- if the vlan is getting destroyed it will be removed and timers will
be stopped
- if the vlan mcast snooping is being disabled
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to use the new port group to port context helper in places where
we cannot pass down the proper context (i.e. functions that can be
called by timers or outside the packet snooping paths).
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add br_multicast_pg_to_port_ctx() which returns the proper port multicast
context from either port or vlan based on bridge option and vlan flags.
As the comment inside explains the locking is a bit tricky, we rely on
the fact that BR_VLFLAG_MCAST_ENABLED requires multicast_lock to change
and we also require it to be held to call that helper. If we find the
vlan under rcu and it still has the flag then we can be sure it will be
alive until we unlock multicast_lock which should be enough.
Note that the context might change from vlan to bridge between different
calls to this helper as the mcast vlan knob requires only rtnl so it should
be used carefully and for read-only/check purposes.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a global knob that controls if vlan multicast snooping is enabled.
The proper contexts (vlan or bridge-wide) will be chosen based on the knob
when processing packets and changing bridge device state. Note that
vlans have their individual mcast snooping enabled by default, but this
knob is needed to turn on bridge vlan snooping. It is disabled by
default. To enable the knob vlan filtering must also be enabled, it
doesn't make sense to have vlan mcast snooping without vlan filtering
since that would lead to inconsistencies. Disabling vlan filtering will
also automatically disable vlan mcast snooping.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers to enable/disable vlan multicast based on its flags, we need
two flags because we need to know if the vlan has multicast enabled
globally (user-controlled) and if it has it enabled on the specific device
(bridge or port). The new private vlan flags are:
- BR_VLFLAG_MCAST_ENABLED: locally enabled multicast on the device, used
when removing a vlan, toggling vlan mcast snooping and controlling
single vlan (kernel-controlled, valid under RTNL and multicast_lock)
- BR_VLFLAG_GLOBAL_MCAST_ENABLED: globally enabled multicast for the
vlan, used to control the bridge-wide vlan mcast snooping for a
single vlan (user-controlled, can be checked under any context)
Bridge vlan contexts are created with multicast snooping enabled by
default to be in line with the current bridge snooping defaults. In
order to actually activate per vlan snooping and context usage a
bridge-wide knob will be added later which will default to disabled.
If that knob is enabled then automatically all vlan snooping will be
enabled. All vlan contexts are initialized with the current bridge
multicast context defaults.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add global and per-port vlan multicast context, only initialized but
still not used. No functional changes intended.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass multicast context pointers to multicast functions instead of bridge/port.
This would make it easier later to switch these contexts to their per-vlan
versions. The patch is basically search and replace, no functional changes.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out the bridge's global multicast context into a separate
structure which will later be used for per-vlan global context.
No functional changes intended.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out the port's multicast context into a separate structure which
will later be shared for per-port,vlan context. No functional changes
intended. We need the structure even if bridge multicast is not defined
to pass down as pointer to forwarding functions.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simple script:
ip link add br0 type bridge
ip link set swp2 master br0
ip link set br0 address 00:01:02:03:04:05
ip link del br0
produces this result on a DSA switch:
[ 421.306399] br0: port 1(swp2) entered blocking state
[ 421.311445] br0: port 1(swp2) entered disabled state
[ 421.472553] device swp2 entered promiscuous mode
[ 421.488986] device swp2 left promiscuous mode
[ 421.493508] br0: port 1(swp2) entered disabled state
[ 421.886107] sja1105 spi0.1: port 1 failed to delete 00:01:02:03:04:05 vid 1 from fdb: -ENOENT
[ 421.894374] sja1105 spi0.1: port 1 failed to delete 00:01:02:03:04:05 vid 0 from fdb: -ENOENT
[ 421.943982] br0: port 1(swp2) entered blocking state
[ 421.949030] br0: port 1(swp2) entered disabled state
[ 422.112504] device swp2 entered promiscuous mode
A very simplified view of what happens is:
(1) the bridge port is created, and the bridge device inherits its MAC
address
(2) when joining, the bridge port (DSA) requests a replay of the
addition of all FDB entries towards this bridge port and towards the
bridge device itself. In fact, DSA calls br_fdb_replay() twice:
br_fdb_replay(br, brport_dev);
br_fdb_replay(br, br);
DSA uses reference counting for the FDB entries. So the MAC address
of the bridge is simply kept with refcount 2. When the bridge port
leaves under normal circumstances, everything cancels out since the
replay of the FDB entry deletion is also done twice per VLAN.
(3) when the bridge MAC address changes, switchdev is notified of the
deletion of the old address and of the insertion of the new one.
But the old address does not really go away, since it had refcount
2, and the new address is added "only" with refcount 1.
(4) when the bridge port leaves now, it will replay a deletion of the
FDB entries pointing towards the bridge twice. Then DSA will
complain that it can't delete something that no longer exists.
It is clear that the problem is that the FDB entries towards the bridge
are replayed too many times, so let's fix that problem.
Fixes: 63c51453c8 ("net: dsa: replay the local bridge FDB entries pointing to the bridge dev too")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20210719093916.4099032-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When an MRD advertisement is received on a bridge port with multicast
snooping enabled, we mark it as a router port automatically, that
includes adding that port to the router port list. The multicast lock
protects that list, but it is not acquired in the MRD advertisement case
leading to a race condition, we need to take it to fix the race.
Cc: stable@vger.kernel.org
Cc: linus.luessing@c0d3.blue
Fixes: 4b3087c7e3 ("bridge: Snoop Multicast Router Advertisements")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a PIM hello packet is received on a bridge port with multicast
snooping enabled, we mark it as a router port automatically, that
includes adding that port the router port list. The multicast lock
protects that list, but it is not acquired in the PIM message case
leading to a race condition, we need to take it to fix the race.
Cc: stable@vger.kernel.org
Fixes: 91b02d3d13 ("bridge: mcast: add router port on PIM hello message")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 2796d0c648 ("bridge: Automatically manage
port promiscuous mode.")
bridges with `vlan_filtering 1` and only 1 auto-port don't
set IFF_PROMISC for unicast-filtering-capable ports.
Normally on port changes `br_manage_promisc` is called to
update the promisc flags and unicast filters if necessary,
but it cannot distinguish between *new* ports and ones
losing their promisc flag, and new ports end up not
receiving the MAC address list.
Fix this by calling `br_fdb_sync_static` in `br_add_if`
after the port promisc flags are updated and the unicast
filter was supposed to have been filled.
Fixes: 2796d0c648 ("bridge: Automatically manage port promiscuous mode.")
Signed-off-by: Wolfgang Bumiller <w.bumiller@proxmox.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port joins a bridge which already has local FDB entries pointing
to the bridge device itself, we would like to offload those, so allow
the "dev" argument to be equal to the bridge too. The code already does
what we need in that case.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Treat addresses added to the bridge itself in the same way as regular
ports and send out a notification so that drivers may sync it down to
the hardware FDB.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Annotate the writer side of fdb->dst:
- fdb_create()
- br_fdb_update()
- fdb_add_entry()
- br_fdb_external_learn_add()
with WRITE_ONCE() and the reader side:
- br_fdb_test_addr()
- br_fdb_update()
- fdb_fill_info()
- fdb_add_entry()
- fdb_delete_by_addr_and_port()
- br_fdb_external_learn_add()
- br_switchdev_fdb_notify()
with compiler barriers such that the readers do not attempt to reload
fdb->dst multiple times, leading to potentially different destination
ports when the fdb entry is updated concurrently.
This is especially important in read-side sections where fdb->dst is
used more than once, but let's convert all accesses for the sake of
uniformity.
Suggested-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the standard IEC 62439-2, in case the node behaves as MRA
and needs to send Test frames on ring ports, then these Test frames need
to have an Option TLV and a Sub-Option TLV which has the type AUTO_MGR.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a switchdev port leaves a LAG that is a bridge port, the switchdev
objects and port attributes offloaded to that port are not removed:
ip link add br0 type bridge
ip link add bond0 type bond mode 802.3ad
ip link set swp0 master bond0
ip link set bond0 master br0
bridge vlan add dev bond0 vid 100
ip link set swp0 nomaster
VLAN 100 will remain installed on swp0 despite it going into standalone
mode, because as far as the bridge is concerned, nothing ever happened
to its bridge port.
Let's extend the bridge vlan, fdb and mdb replay functions to take a
'bool adding' argument, and make DSA and ocelot call the replay
functions with 'adding' as false from the switchdev unsync path, for the
switch port that leaves the bridge.
Note that this patch in itself does not salvage anything, because in the
current pull mode of operation, DSA still needs to call the replay
helpers with adding=false. This will be done in another patch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the arguments and local variables for the newly added switchdev
replay helpers can be const, so let's make them so.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a slight inconvenience in the switchdev replay helpers added
recently, and this is when:
ip link add br0 type bridge
ip link add bond0 type bond
ip link set bond0 master br0
bridge vlan add dev bond0 vid 100
ip link set swp0 master bond0
ip link set swp1 master bond0
Since the underlying driver (currently only DSA) asks for a replay of
VLANs when swp0 and swp1 join the LAG because it is bridged, what will
happen is that DSA will try to react twice on the VLAN event for swp0.
This is not really a huge problem right now, because most drivers accept
duplicates since the bridge itself does, but it will become a problem
when we add support for replaying switchdev object deletions.
Let's fix this by adding a blank void *ctx in the replay helpers, which
will be passed on by the bridge in the switchdev notifications. If the
context is NULL, everything is the same as before. But if the context is
populated with a valid pointer, the underlying switchdev driver
(currently DSA) can use the pointer to 'see through' the bridge port
(which in the example above is bond0) and 'know' that the event is only
for a particular physical port offloading that bridge port, and not for
all of them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 2c4eca3ef7 ("net: bridge: switchdev: include local flag
in FDB notifications"), the bridge emits SWITCHDEV_FDB_ADD_TO_DEVICE
events with the is_local flag populated (but we ignore it nonetheless).
We would like DSA to start treating this bit, but it is still not
populated by the replay helper, so add it there too.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return statements are not needed in Void function.
Signed-off-by: gushengxian <gushengxian@yulong.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The continue statement at the end of a for-loop has no effect,
invert the if expression and remove the continue.
Addresses-Coverity: ("Continue has no effect")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a tunnel_dst null pointer dereference due to lockless
access in the tunnel egress path. When deleting a vlan tunnel the
tunnel_dst pointer is set to NULL without waiting a grace period (i.e.
while it's still usable) and packets egressing are dereferencing it
without checking. Use READ/WRITE_ONCE to annotate the lockless use of
tunnel_id, use RCU for accessing tunnel_dst and make sure it is read
only once and checked in the egress path. The dst is already properly RCU
protected so we don't need to do anything fancy than to make sure
tunnel_id and tunnel_dst are read only once and checked in the egress path.
Cc: stable@vger.kernel.org
Fixes: 11538d039a ("bridge: vlan dst_metadata hooks in ingress and egress paths")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the standard IEC 62439-2, the number of transitions needs
to be counted for each transition 'between' ring state open and ring
state closed and not from open state to closed state.
Therefore fix this for both ring and interconnect ring.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable br is assigned a value that is not being read after
exiting case IFLA_STATS_LINK_XSTATS_SLAVE. The assignment is
redundant and can be removed.
Addresses-Coverity ("Unused value")
Signed-off-by: Nigel Christian <nigel.l.christian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The br_ip6_multicast_add_router() prototype is defined only when
CONFIG_IPV6 is enabled, but the function is always referenced, so there
is this build error with CONFIG_IPV6 not defined:
net/bridge/br_multicast.c: In function ‘__br_multicast_enable_port’:
net/bridge/br_multicast.c:1743:3: error: implicit declaration of function ‘br_ip6_multicast_add_router’; did you mean ‘br_ip4_multicast_add_router’? [-Werror=implicit-function-declaration]
1743 | br_ip6_multicast_add_router(br, port);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
| br_ip4_multicast_add_router
net/bridge/br_multicast.c: At top level:
net/bridge/br_multicast.c:2804:13: warning: conflicting types for ‘br_ip6_multicast_add_router’
2804 | static void br_ip6_multicast_add_router(struct net_bridge *br,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
net/bridge/br_multicast.c:2804:13: error: static declaration of ‘br_ip6_multicast_add_router’ follows non-static declaration
net/bridge/br_multicast.c:1743:3: note: previous implicit declaration of ‘br_ip6_multicast_add_router’ was here
1743 | br_ip6_multicast_add_router(br, port);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix this build error by moving the definition out of the #ifdef.
Fixes: a3c02e769e ("net: bridge: mcast: split multicast router state for IPv4 and IPv6")
Signed-off-by: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_multicast_is_router takes two arguments when bridge IGMP is enabled
and just one when it's disabled, fix the stub to take two as well.
Fixes: 1a3065a268 ("net: bridge: mcast: prepare is-router function for mcast router split")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Acked-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
To properly support routable multicast addresses in batman-adv in a
group-aware way, a batman-adv node needs to know if it serves multicast
routers.
This adds a function to the bridge to export this so that batman-adv
can then make full use of the Multicast Router Discovery capability of
the bridge.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have split the multicast router state into two, one for IPv4
and one for IPv6, also add individual timers to the mdb netlink router
port dump. Leaving the old timer attribute for backwards compatibility.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
A multicast router for IPv4 does not imply that the same host also is a
multicast router for IPv6 and vice versa.
To reduce multicast traffic when a host is only a multicast router for
one of these two protocol families, keep router state for IPv4 and IPv6
separately. Similar to how querier state is kept separately.
For backwards compatibility for netlink and switchdev notifications
these two will still only notify if a port switched from either no
IPv4/IPv6 multicast router to any IPv4/IPv6 multicast router or the
other way round. However a full netlink MDB router dump will now also
include a multicast router timeout for both IPv4 and IPv6.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the upcoming split of multicast router state into
their IPv4 and IPv6 variants split router port deletion and notification
into two functions. When we disable a port for instance later we want to
only send one notification to switchdev and netlink for compatibility
and want to avoid sending one for IPv4 and one for IPv6. For that the
split is needed.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the upcoming split of multicast router state into
their IPv4 and IPv6 variants move the protocol specific router list
and timer access to ip4 wrapper functions.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the upcoming split of multicast router state into
their IPv4 and IPv6 variants move the protocol specific timer access to
an ip4 wrapper function.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the upcoming split of multicast router state into
their IPv4 and IPv6 variants make br_multicast_is_router() protocol
family aware.
Note that for now br_ip6_multicast_is_router() uses the currently still
common ip4_mc_router_timer for now. It will be renamed to
ip6_mc_router_timer later when the split is performed.
While at it also renames the "1" and "2" constants in
br_multicast_is_router() to the MDB_RTR_TYPE_TEMP_QUERY and
MDB_RTR_TYPE_PERM enums.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the upcoming split of multicast router state into
their IPv4 and IPv6 variants and as the br_multicast_mark_router() will
be split for that remove the select querier wrapper and instead add
ip4 and ip6 variants for br_multicast_query_received().
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the upcoming split of multicast router state into
their IPv4 and IPv6 variants and to avoid IPv6 #ifdef clutter later add
some inline functions for the protocol specific parts in the mdb router
netlink code. Also the we need iterate over the port instead of router
list to be able put one router port entry with both the IPv4 and IPv6
multicast router info later.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the upcoming split of multicast router state into
their IPv4 and IPv6 variants and to avoid IPv6 #ifdef clutter later add
two wrapper functions for router node retrieval in the payload
forwarding code.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for the upcoming split of multicast router state into
their IPv4 and IPv6 variants, rename the affected variable to the IPv4
version first to avoid some renames in later commits.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a crash in the function br_get_link_af_size_filtered,
as the port_exists(dev) is true and the rx_handler_data of dev is NULL.
But the rx_handler_data of dev is correct saved in vmcore.
The oops looks something like:
...
pc : br_get_link_af_size_filtered+0x28/0x1c8 [bridge]
...
Call trace:
br_get_link_af_size_filtered+0x28/0x1c8 [bridge]
if_nlmsg_size+0x180/0x1b0
rtnl_calcit.isra.12+0xf8/0x148
rtnetlink_rcv_msg+0x334/0x370
netlink_rcv_skb+0x64/0x130
rtnetlink_rcv+0x28/0x38
netlink_unicast+0x1f0/0x250
netlink_sendmsg+0x310/0x378
sock_sendmsg+0x4c/0x70
__sys_sendto+0x120/0x150
__arm64_sys_sendto+0x30/0x40
el0_svc_common+0x78/0x130
el0_svc_handler+0x38/0x78
el0_svc+0x8/0xc
In br_add_if(), we found there is no guarantee that
assigning rx_handler_data to dev->rx_handler_data
will before setting the IFF_BRIDGE_PORT bit of priv_flags.
So there is a possible data competition:
CPU 0: CPU 1:
(RCU read lock) (RTNL lock)
rtnl_calcit() br_add_slave()
if_nlmsg_size() br_add_if()
br_get_link_af_size_filtered() -> netdev_rx_handler_register
...
// The order is not guaranteed
... -> dev->priv_flags |= IFF_BRIDGE_PORT;
// The IFF_BRIDGE_PORT bit of priv_flags has been set
-> if (br_port_exists(dev)) {
// The dev->rx_handler_data has NOT been assigned
-> p = br_port_get_rcu(dev);
....
-> rcu_assign_pointer(dev->rx_handler_data, rx_handler_data);
...
Fix it in br_get_link_af_size_filtered, using br_port_get_check_rcu() and checking the return value.
Signed-off-by: Zhang Zhengming <zhangzhengming@huawei.com>
Reviewed-by: Zhao Lei <zhaolei69@huawei.com>
Reviewed-by: Wang Xiaogang <wangxiaogang3@huawei.com>
Suggested-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPv6 Multicast Router Advertisements parsing has the following two
issues:
For one thing, ICMPv6 MRD Advertisements are smaller than ICMPv6 MLD
messages (ICMPv6 MRD Adv.: 8 bytes vs. ICMPv6 MLDv1/2: >= 24 bytes,
assuming MLDv2 Reports with at least one multicast address entry).
When ipv6_mc_check_mld_msg() tries to parse an Multicast Router
Advertisement its MLD length check will fail - and it will wrongly
return -EINVAL, even if we have a valid MRD Advertisement. With the
returned -EINVAL the bridge code will assume a broken packet and will
wrongly discard it, potentially leading to multicast packet loss towards
multicast routers.
The second issue is the MRD header parsing in
br_ip6_multicast_mrd_rcv(): It wrongly checks for an ICMPv6 header
immediately after the IPv6 header (IPv6 next header type). However
according to RFC4286, section 2 all MRD messages contain a Router Alert
option (just like MLD). So instead there is an IPv6 Hop-by-Hop option
for the Router Alert between the IPv6 and ICMPv6 header, again leading
to the bridge wrongly discarding Multicast Router Advertisements.
To fix these two issues, introduce a new return value -ENODATA to
ipv6_mc_check_mld() to indicate a valid ICMPv6 packet with a hop-by-hop
option which is not an MLD but potentially an MRD packet. This also
simplifies further parsing in the bridge code, as ipv6_mc_check_mld()
already fully checks the ICMPv6 header and hop-by-hop option.
These issues were found and fixed with the help of the mrdisc tool
(https://github.com/troglobit/mrdisc).
Fixes: 4b3087c7e3 ("bridge: Snoop Multicast Router Advertisements")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
The compat layer needs to parse untrusted input (the ruleset)
to translate it to a 64bit compatible format.
We had a number of bugs in this department in the past, so allow users
to turn this feature off.
Add CONFIG_NETFILTER_XTABLES_COMPAT kconfig knob and make it default to y
to keep existing behaviour.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ebtables stores the table internal data (what gets passed to the
ebt_do_table() interpreter) in struct net.
nftables keeps the internal interpreter format in pernet lists
and passes it via the netfilter core infrastructure (priv pointer).
Do the same for ebtables: the nf_hook_ops are duplicated via kmemdup,
then the ops->priv pointer is set to the table that is being registered.
After that, the netfilter core passes this table info to the hookfn.
This allows to remove the pointers from struct net.
Same pattern can be applied to ip/ip6/arptables.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When CONFIG_NET_SWITCHDEV is disabled, the shim for switchdev_port_attr_set
inside br_mc_disabled_update returns -EOPNOTSUPP. This is not caught,
and propagated to the caller of br_multicast_add_port, preventing ports
from joining the bridge.
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Fixes: ae1ea84b33 ("net: bridge: propagate error code and extack from br_mc_disabled_update")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
- keep the ZC code, drop the code related to reinit
net/bridge/netfilter/ebtables.c
- fix build after move to net_generic
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As explained in bugfix commit 6ab4c3117a ("net: bridge: don't notify
switchdev for local FDB addresses") as well as in this discussion:
https://lore.kernel.org/netdev/20210117193009.io3nungdwuzmo5f7@skbuf/
the switchdev notifiers for FDB entries managed to have a zero-day bug,
which was that drivers would not know what to do with local FDB entries,
because they were not told that they are local. The bug fix was to
simply not notify them of those addresses.
Let us now add the 'is_local' bit to bridge FDB entries, and make all
drivers ignore these entries by their own choice.
Co-developed-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having to add more and more arguments to
br_switchdev_fdb_call_notifiers, get rid of it and build the info
struct directly in br_switchdev_fdb_notify.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov