These aren't used anywhere (hostapd, wpa_supplicant) and until we
have a proper interface to the rate control algorithms they don't
make much sense either since e.g. rc80211_lowest won't honour them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch separates the monitor interface start_xmit from the
subif start xmit (those other devices have 802.3 framing, monitor
interfaces have radiotap framing)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add supported channels info in SIOCGIWRANGE implementation.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove ieee80211_set_aid_for_sta and associated code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This constant is unused.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes mac80211 show transmitted frames on monitor interfaces,
including radiotap headers that indicate some transmission parameters.
The shown parameters will need to be expanded, but this should work as
a basis to work from.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The initial rate for STA's using rc80211_simple is set to the last
rate in the rate table. For situations for which the signal is weak,
the rate may be too high for authentication and association. Although
the rc80211_simple module will adjust the speed, the response may not
be fast enough for a successful connection. This modification sets the
initial rate to the lowest supported value.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At present, transmission rate information for mac80211 is available only
if verbose debugging is turned on, and then only in the logs. This patch
implements the SIOCGIWRATE ioctl, which adds the current transmission rate to
the output of iwconfig.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac80211 stops the tx queues during scans. This is wrong with respect
to the master deivce tx queue, since stopping it prevents any probes
from being sent during the scan. Instead, they accumulate in the queue
and are only sent after the scan is finished, which is obviously
wrong.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a typo in mac80211's debugfs.c.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_open should always set the carrier status since we may have set
it to off before.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We forget to free all the fragments when defraging them into one packet.
Signed-off-by: Hong Liu <hong.liu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some APs have strict checking between associate and reassociate. In
a case when an AP is restarted during a connection, it denies the
mac80211 reassoc request since this is a new association for the AP.
To fix this problem, we need to check the status code against
WLAN_STATUS_REASSOC_NO_ASSOC and clear ifsta->prev_bssid_set in
handling the association failure response.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
| CC net/mac80211/ieee80211_sta.o
| In file included from linux/net/mac80211/ieee80211_sta.c:31:
| include2/asm/delay.h: In function '__const_udelay':
| include2/asm/delay.h:33: error: 'loops_per_jiffy' undeclared (first use in this function)
| include2/asm/delay.h:33: error: (Each undeclared identifier is reported only once
| include2/asm/delay.h:33: error: for each function it appears in.)
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export various mac80211 internal variables through debugfs.
Signed-off-by: Jiri Benc <jbenc@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg