Commit a65a6f14dc ("USB: serial: fix race between probe and open")
fixed a race between probe and open, which could lead to crashes when a
not yet fully initialised port was being opened.
This race was later incidentally closed by commit 7e73eca6a7 ("TTY:
move cdev_add to tty_register_device") which moved character-device
registration from tty_register_driver to tty_register_device, which
isn't called until the port has been fully set up.
Remove the now redundant workaround which had the negative side effect
of not allowing a port to be opened immediately after user space had
been notified of a new tty device.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop some unnecessary termios-flag debugging that have been faithfully
reproduced in a few old drivers, including the "clfag" typo and all.
This also addresses a compiler warning on sparc where tcflag_t is
unsigned long and would have required an explicit cast.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Setup each port to use the first bulk-out endpoint in calc_num_ports so
that core allocates the corresponding port resources for us.
Signed-off-by: Johan Hovold <johan@kernel.org>
Setup each port to use the first bulk-out endpoint in calc_num_ports so
that core allocates the corresponding port resources for us.
Signed-off-by: Johan Hovold <johan@kernel.org>
Add an explicit sanity check to make sure we have the expected
endpoints. This will provide a descriptive error message in case an
expected endpoint is missing when probing.
Note that the driver already gracefully fails to probe (albeit with a
less descriptive error message) if a bulk-in endpoint is missing, and an
attempt to write to a port whose device lack a bulk-out endpoint would
fail with -ENODEV.
Signed-off-by: Johan Hovold <johan@kernel.org>
Print a message and register two ports for interfaces for which we do
not know how many ports there are instead of binding, allocating
resources, but not register any ports.
This provides a hint that anyone adding a dynamic device id must also
provide a reference id (driver info) from which the port count can be
retrieved, for example:
echo <vid> <pid> 0 0x110A 0x1410 > new_id
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the new endpoint-remap functionality to configure the ports for
treo devices instead of poking around in the port structures after the
ports have been setup.
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the new endpoint-remap functionality to configure the ports for
clie_5 devices.
Note that the same bulk-out endpoint is being used for both ports.
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop the redundant calc_num_ports callback from the clie_5 type, for
which the callback always returns zero and hence falls back to the type
num_ports value (2).
Signed-off-by: Johan Hovold <johan@kernel.org>
These devices always require at least one bulk-out endpoint so let core
verify that.
This avoids attempting to send bulk data to the default pipe when
downloading firmware in boot mode.
Note that further endpoints are still needed when not in boot mode.
Signed-off-by: Johan Hovold <johan@kernel.org>
Now that the endpoint-port mapping has been properly set up during
probe, we can switch to using the more efficient generic write
implementation.
Note that this currently means that chars_in_buffer now overcounts
slightly as we always write a full endpoint-sized packet.
Also add a copyright entry.
Signed-off-by: Johan Hovold <johan@kernel.org>
These devices use the second bulk-out endpoint for writing. Instead of
using the resources of the second port structure setup by core, use the
new endpoint-remap functionality to simply ignore the first bulk-out
endpoint. This specifically avoids allocating resources for the unused
endpoint.
Note that the disconnect callback was always redundant as all URBs would
have been killed by USB core on disconnect.
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up the endpoint sanity check by letting core verify the single
interrupt endpoint, and verifying the bulk endpoints in calc_num_ports
after having determined the number of ports.
Note that the static type num_ports field was neither correct or used
(since calc_num_ports never returns zero).
Signed-off-by: Johan Hovold <johan@kernel.org>
This driver have treated the interrupt endpoint as optional despite it
always being present (according to the datasheet). Let's consider it
mandatory instead.
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up the mcs7715 port setup by using the new endpoint-remap
functionality provided by core. Instead of poking around in internal
port-structure fields, simply swap the endpoint descriptors of the two
ports in calc_num_ports before the port structures are even allocated.
Note that we still need to override the default interrupt completion
handler.
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop the redundant read-urb check from open. The presence of a bulk-in
endpoint is now verified during probe and core has allocated the
corresponding resources.
Signed-off-by: Johan Hovold <johan@kernel.org>
Verify that the required interrupt endpoint is present at probe rather
than at open to avoid allocating resources for an unusable device.
Note that the endpoint is only required when in download mode.
Signed-off-by: Johan Hovold <johan@kernel.org>
These devices always require at least one bulk-out endpoint so let core
verify that.
This avoids attempting to send bulk data to the default pipe when
downloading firmware in boot mode.
Note that further endpoints are still needed when not in boot mode.
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the calc_num_ports rather than attach callback to verify that the
required endpoints are present when in download mode.
This avoids allocating port resources for interfaces that won't be bound.
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the calc_num_ports callback to ignore unused endpoints.
The driver binds to any interface with at least one bulk-in and one
bulk-out endpoint, but some devices can have three or more endpoints of
which only either the first or second pair of endpoints is needed.
This avoids allocating resources for unused endpoints, and specifically
a port is no longer registered for the unused first endpoint pair when
there are more than three endpoints.
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the calc_num_ports rather than attach callback to determine which
interface to bind to in order to avoid allocating port-resources for
interfaces that won't be bound.
Signed-off-by: Johan Hovold <johan@kernel.org>
We can now abort probe early after an error in calc_num_ports by
returning an errno instead of attempting to continue probing but not
register any ports.
Signed-off-by: Johan Hovold <johan@kernel.org>
Simplify the endpoint sanity check by letting core verify that the
required endpoints are present and moving the max-packet check to
calc_num_ports.
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the calc_num_ports rather than probe callback to determine which
interface to bind to.
This allows us to remove some duplicate code.
Signed-off-by: Johan Hovold <johan@kernel.org>
Implement the "horrible endpoint hack" for some legacy devices as a
quirk and clean up the code somewhat.
Note that the bulk-endpoint check can be removed as core will already
have verified this.
Signed-off-by: Johan Hovold <johan@kernel.org>
Some pl2303 devices require the use of the interrupt endpoint of an
unrelated interface. This has so far been dealt with in usb-serial core,
but can now be moved to a driver calc_num_ports callback.
Note that we relax the endpoint requirements checked by core and instead
verify that we have an interrupt-in endpoint in calc_num_ports for all
devices so that the hack can first be applied.
Signed-off-by: Johan Hovold <johan@kernel.org>
Relax the generic driver bulk-endpoint requirement. The driver handles
devices without bulk-out endpoints just fine these days.
Signed-off-by: Johan Hovold <johan@kernel.org>
Add a calc_num_ports callback to the generic driver and verify that the
device has the required endpoints there instead of in core.
Note that the generic driver num_ports field was never used.
Signed-off-by: Johan Hovold <johan@kernel.org>
Add a probe callback to the generic driver and print the
only-for-testing message there.
This is a first step in getting rid of the CONFIG_USB_SERIAL_GENERIC
ifdef from usb-serial core.
Signed-off-by: Johan Hovold <johan@kernel.org>
Allow subdrivers to modify the port-endpoint mapping by passing the
endpoint descriptors to calc_num_ports.
The callback can now also be used to verify that the required endpoints
exists and abort probing otherwise.
This will allow us to get rid of a few hacks in subdrivers that are
already modifying the port-endpoint mapping (or aborting probe due to
missing endpoints), but only after the port structures have been setup.
Signed-off-by: Johan Hovold <johan@kernel.org>
This is a Dell branded Sierra Wireless EM7455.
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Simplify the endpoint sanity check by letting core verify that the
required endpoints are present.
Note that the driver registers four ports but uses five bulk-endpoint
pairs.
Signed-off-by: Johan Hovold <johan@kernel.org>
Simplify the endpoint sanity check by letting core verify that the
required endpoints are present.
Note that the driver uses the second bulk-out endpoint for writing.
Signed-off-by: Johan Hovold <johan@kernel.org>
Simplify the endpoint sanity check by letting core verify that the
required endpoints are present.
Note that the driver expects two bulk-endpoint pairs also for mcs7715
devices for which only one serial port is registered.
Signed-off-by: Johan Hovold <johan@kernel.org>
Simplify the endpoint sanity check by letting core verify that the
required endpoints are present.
Also require the presence of a bulk-out endpoint, something which
prevents the driver from trying to send bulk messages over the control
pipe should a bulk-out endpoint be missing.
Signed-off-by: Johan Hovold <johan@kernel.org>
Simplify the endpoint sanity check by letting core verify that the
required endpoints are present.
Note that this driver uses an additional bulk-endpoint pair as an
out-of-band port.
Signed-off-by: Johan Hovold <johan@kernel.org>
Allow drivers to specify a minimum number of endpoints per type, which
USB serial core will verify after subdriver probe has returned (where
the current alternate setting may have been changed).
Signed-off-by: Johan Hovold <johan@kernel.org>
Since commit 0a8fd13462 ("USB: fix problems with duplicate endpoint
addresses") USB core guarantees that there are no more than 15 endpoint
descriptors per type (and altsetting) so the corresponding overflow
checks can now be replaced with a compile-time check on the array sizes
(and indirectly the maximum number of ports).
Signed-off-by: Johan Hovold <johan@kernel.org>
Refactor and clean up endpoint handling.
This specifically moves the endpoint-descriptor arrays of the stack.
Note that an err_free_epds label is not yet added to avoid a compilation
warning when neither CONFIG_USB_SERIAL_PL2303 or
CONFIG_USB_SERIAL_GENERIC is selected.
Signed-off-by: Johan Hovold <johan@kernel.org>
Add Quectel UC15, UC20, EC21, and EC25. The EC20 is handled by
qcserial due to a USB VID/PID conflict with an existing Acer
device.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The 'store' function for the "event_char" device attribute currently
expects a base 10 value. The value is composed of an enable bit in bit
8 and an 8-bit "event character" code in bits 7 to 0. It seems
reasonable to allow hexadecimal and octal numbers to be written to the
device attribute in addition to decimal. Make it so.
Change the debug message to show the value in hexadecimal, rather than
decimal.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
The "event_char" device attribute value, when written, is interpreted as
an enable bit in bit 8, and an "event character" in bits 7 to 0.
Return an error -EINVAL for out-of-range values. Use kstrtouint() to
parse the integer instead of the obsolete simple_strtoul().
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
Valid latency timer values are between 1 ms and 255 ms in 1 ms steps.
The store function for the "latency_timer" device attribute currently
allows any value, although only the lower 16 bits will be sent to the
device, and the device only stores the lower 8 bits. The hardware
appears to accept the (invalid) value 0 and treats it the same as 1
(resulting in a latency of 1 ms).
Change the latency_timer_store() function to accept only the values 0 to
255, returning an error -EINVAL for out-of-range values. Call
kstrtou8() to parse the integer instead of the obsolete
simple_strtoul().
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
If a BM type chip has iSerialNumber set to 0 in its EEPROM, an incorrect
value is read from the bcdDevice field of the USB descriptor, making it
look like an AM type chip. Attempt to correct this in
ftdi_determine_type() by attempting to read the latency timer for an AM
type chip if it has iSerialNumber set to 0. If that succeeds, assume it
is a BM type chip.
Currently, read_latency_timer() bails out without reading the latency
timer for an AM type chip, so factor out the guts of
read_latency_timer() into a new function _read_latency_timer() that
attempts to read the latency timer regardless of chip type, and returns
either the latency timer value or a negative error number.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
The latency timer was introduced with the FT232BM and FT245BM chips. Do
not bother attempting to read or write it for older chip versions.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add missing sanity check to the bulk-in completion handler to avoid an
integer underflow that could be triggered by a malicious device.
This avoids leaking up to 56 bytes from after the URB transfer buffer to
user space.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add missing sanity check to the bulk-in completion handler to avoid an
integer underflow that can be triggered by a malicious device.
This avoids leaking 128 kB of memory content from after the URB transfer
buffer to user space.
Fixes: 8c209e6782 ("USB: make actual_length in struct urb field u32")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org> # 2.6.30
Signed-off-by: Johan Hovold <johan@kernel.org>
This driver needlessly took another reference to the tty on open, a
reference which was then never released on close. This lead to not just
a leak of the tty, but also a driver reference leak that prevented the
driver from being unloaded after a port had once been opened.
Fixes: 4a90f09b20 ("tty: usb-serial krefs")
Cc: stable <stable@vger.kernel.org> # 2.6.28
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix a NULL-pointer dereference in the interrupt callback should a
malicious device send data containing a bad port number by adding the
missing sanity check.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
A recent change claimed to fix an off-by-one error in the OOB-port
completion handler, but instead introduced such an error. This could
specifically led to modem-status changes going unnoticed, effectively
breaking TIOCMGET.
Note that the offending commit fixes a loop-condition underflow and is
marked for stable, but should not be backported without this fix.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 2d38088921 ("USB: serial: digi_acceleport: fix OOB data sanity
check")
Cc: stable <stable@vger.kernel.org> # v2.6.30: 2d38088921
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Here is the big USB and PHY driver updates for 4.11-rc1.
Nothing major, just the normal amount of churn in the usb gadget and dwc
and xhci controllers, new device ids, new phy drivers, a new usb-serial
driver, and a few other minor changes in different USB drivers.
All have been in linux-next for a long time with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWK2lrg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykh7ACffotTJvB/gwpuSIWh6qhA8KQ9mH8AnjlxMafv
b5b3vfOXJ8/N0Go25VwI
=7fqN
-----END PGP SIGNATURE-----
Merge tag 'usb-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB and PHY driver updates for 4.11-rc1.
Nothing major, just the normal amount of churn in the usb gadget and
dwc and xhci controllers, new device ids, new phy drivers, a new
usb-serial driver, and a few other minor changes in different USB
drivers.
All have been in linux-next for a long time with no reported issues"
* tag 'usb-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (265 commits)
usb: cdc-wdm: remove logically dead code
USB: serial: keyspan: drop header file
USB: serial: io_edgeport: drop io-tables header file
usb: musb: add code comment for clarification
usb: misc: add USB251xB/xBi Hi-Speed Hub Controller Driver
usb: misc: usbtest: remove redundant check on retval < 0
USB: serial: upd78f0730: sort device ids
USB: serial: upd78f0730: add ID for EVAL-ADXL362Z
ohci-hub: fix typo in dbg_port macro
usb: musb: dsps: Manage CPPI 4.1 DMA interrupt in DSPS
usb: musb: tusb6010: Clean up tusb_omap_dma structure
usb: musb: cppi_dma: Clean up cppi41_dma_controller structure
usb: musb: cppi_dma: Clean up cppi structure
usb: musb: cppi41: Detect aborted transfers in cppi41_dma_callback()
usb: musb: dma: Add a DMA completion platform callback
drivers: usb: usbip: Add missing break statement to switch
usb: mtu3: remove redundant dev_err call in get_ssusb_rscs()
USB: serial: mos7840: fix another NULL-deref at open
USB: serial: console: clean up sanity checks
USB: serial: console: fix uninitialised spinlock
...
Core changes:
- Switch the generic pin config argument from 16 to 24 bits,
only use 8 bits for the configuration type. We might need to
encode more information about a certain setting than we need
to encode different generic settings.
- Add a cross-talk API to the pin control GPIO back-end,
utilizing pinctrl_gpio_set_config() from GPIO drivers that
want to set up a certain pin configuration in the back-end.
This also includes the .set_config() refactoring of the
GPIO chips, so that they pass a generic configuration for
things like debouncing and single ended (typically open
drain). This change has also been merged in an immutable
branch to the GPIO tree.
- Take hogs with a delayed work, so that we finalize probing
a pin controller before trying to get any hogs.
- For pin controllers putting all group and function definitions
into the device tree, we now have generic code to deal with
this and it is used in two drivers so far.
- Simplifications of the pin request conflict check.
- Make dt_free_map() optional.
Updates to drivers:
- pinctrl-single now use the generic helpers to generate dynamic
group and function tables from the device tree.
- Texas Instruments IOdelay configuration driver add-on to
pinctrl-single.
- i.MX: use radix trees to store groups and functions, use the new
generic group and function helpers to manage them.
- Intel: add support for hardware debouncing and 1K pull-down.
New subdriver for the Gemini Lake SoC.
- Renesas SH-PFC: drive strength and bias support, CAN bus muxing,
MSIOF, SDHI, HSCIF for r8a7796. Gyro-ADC supporton r8a7791.
- Aspeed: use syscon cross-dependencies to set up related bits in
the LPC host controller and display controller.
- Aspeed: finalize G4 and G5 support. Fix mux configuration on
GPIOs. Add banks Y, Z, AA, AB and AC.
- AMD: support additional GPIO.
- STM32: set this controller to strict muxing mode.
STM32H743 MCU support.
- Allwinner sunxi: deep simplifications on how to support
subvariants of SoCs without adding to much SoC-specific data
for each subvariant, especially for sun5i variants. New driver
for V3s SoCs. New driver for the H5 SoC. Support A31/A31s
variants with the new variant framework.
- Mvebu: simplifications to use a MMIO and regmap abstraction.
New subdrivers for the 98DX3236, 98DX5241 SoCs.
- Samsung Exynos: delete Exynos4415 support. Add crosstalk to the
SoC driver to access regmaps. Add infrastructure for pin-bank
retention control. Clean out the pin retention control from
arch/arm/mach-exynos and arch/arm/mach-s5p and put it properly
in the Samsung pin control driver(s).
- Meson: add HDMI HPD/DDC pins. Add pwm_ao_b pin.
- Qualcomm: use raw spinlock variants: this makes the qualcomm
driver realtime-safe.
-----BEGIN PGP SIGNATURE-----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=IMY0
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Pin control bulk changes for the v4.11 kernel cycle.
Core changes:
- Switch the generic pin config argument from 16 to 24 bits, only use
8 bits for the configuration type. We might need to encode more
information about a certain setting than we need to encode
different generic settings.
- Add a cross-talk API to the pin control GPIO back-end, utilizing
pinctrl_gpio_set_config() from GPIO drivers that want to set up a
certain pin configuration in the back-end.
This also includes the .set_config() refactoring of the GPIO chips,
so that they pass a generic configuration for things like
debouncing and single ended (typically open drain). This change has
also been merged in an immutable branch to the GPIO tree.
- Take hogs with a delayed work, so that we finalize probing a pin
controller before trying to get any hogs.
- For pin controllers putting all group and function definitions into
the device tree, we now have generic code to deal with this and it
is used in two drivers so far.
- Simplifications of the pin request conflict check.
- Make dt_free_map() optional.
Updates to drivers:
- pinctrl-single now use the generic helpers to generate dynamic
group and function tables from the device tree.
- Texas Instruments IOdelay configuration driver add-on to
pinctrl-single.
- i.MX: use radix trees to store groups and functions, use the new
generic group and function helpers to manage them.
- Intel: add support for hardware debouncing and 1K pull-down. New
subdriver for the Gemini Lake SoC.
- Renesas SH-PFC: drive strength and bias support, CAN bus muxing,
MSIOF, SDHI, HSCIF for r8a7796. Gyro-ADC supporton r8a7791.
- Aspeed: use syscon cross-dependencies to set up related bits in the
LPC host controller and display controller.
- Aspeed: finalize G4 and G5 support. Fix mux configuration on GPIOs.
Add banks Y, Z, AA, AB and AC.
- AMD: support additional GPIO.
- STM32: set this controller to strict muxing mode. STM32H743 MCU
support.
- Allwinner sunxi: deep simplifications on how to support subvariants
of SoCs without adding to much SoC-specific data for each
subvariant, especially for sun5i variants. New driver for V3s SoCs.
New driver for the H5 SoC. Support A31/A31s variants with the new
variant framework.
- Mvebu: simplifications to use a MMIO and regmap abstraction. New
subdrivers for the 98DX3236, 98DX5241 SoCs.
- Samsung Exynos: delete Exynos4415 support. Add crosstalk to the SoC
driver to access regmaps. Add infrastructure for pin-bank retention
control. Clean out the pin retention control from
arch/arm/mach-exynos and arch/arm/mach-s5p and put it properly in
the Samsung pin control driver(s).
- Meson: add HDMI HPD/DDC pins. Add pwm_ao_b pin.
- Qualcomm: use raw spinlock variants: this makes the qualcomm driver
realtime-safe"
* tag 'pinctrl-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (111 commits)
pinctrl: samsung: Fix return value check in samsung_pinctrl_get_soc_data()
pinctrl: intel: unlock on error in intel_config_set_pull()
pinctrl: berlin: make bool drivers explicitly non-modular
pinctrl: spear: make bool drivers explicitly non-modular
pinctrl: mvebu: make bool drivers explicitly non-modular
pinctrl: sunxi: make sun5i explicitly non-modular
pinctrl: sunxi: Remove stray printk call in sun5i driver's probe function
pinctrl: samsung: mark PM functions as __maybe_unused
pinctrl: sunxi: Remove redundant A31s pinctrl driver
pinctrl: sunxi: Support A31/A31s with pinctrl variants
pinctrl: Amend bindings for STM32 pinctrl
pinctrl: Add STM32 pinctrl driver DT bindings
pinctrl: stm32: Add STM32H743 MCU support
include: dt-bindings: Add STM32H7 pinctrl DT defines
gpio: aspeed: Remove dependence on GPIOF_* macros
pinctrl: stm32: fix bad location of gpiochip_lock_as_irq
drivers: pinctrl: add driver for Allwinner H5 SoC
pinctrl: intel: Add Intel Gemini Lake pin controller support
pinctrl: intel: Add support for 1k additional pull-down
pinctrl: intel: Add support for hardware debouncer
...
Here's one more device id for the new upd78f0730 driver and three
clean-up patches that are mostly moving some code around.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=9eBj
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.11-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.11-rc1 part 2
Here's one more device id for the new upd78f0730 driver and three
clean-up patches that are mostly moving some code around.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
Move all declarations and definitions in keyspan.h to keyspan.c, which
is the only place were they are used.
This specifically moves the driver device-id tables and usb-serial
driver definitions to the source file where they are expected to be
found.
While at it, fix up some multi-line comments and minor white-space
issues (spaces instead of tabs and superfluous white space).
Note that the information in the comment header of the removed header
file is also present in the source file.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Move the driver device-id tables and usb-serial driver definitions to
the source file where they are expected to be found.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The adaptor on Analog Devices EVAL-ADXL362Z development board is used
to flash and debug firmware of on-board Renesas RL78/G13 MCU.
Also added support of the 153600 baud rate, since the stock firmware
uses it.
Signed-off-by: Maksim Salau <maksim.salau@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
These updates include
- a new driver for Renesas uPD78F0730-based devices
- several fixes of failures to check for short transfers, some of which could
lead to minor information leaks, and in one case a loop-condition underflow
- a fix of a long-standing regression in the ftdi_sio driver which resulted
in excessive bulk-in interrupts
- a fix for ftdi_sio line-status over-reporting which could lead to an
endless stream of NULL-characters being forwarded to user space
- a fix for a regression in the console driver
- a fix for another mos7840 NULL-pointer dereference due to a missing endpoint
sanity check
Included are also some clean ups and fixes for various minor issues, as well as
a couple of new device IDs that came in late.
All but the final patch have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----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=Ma49
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.11-rc1
These updates include
- a new driver for Renesas uPD78F0730-based devices
- several fixes of failures to check for short transfers, some of which could
lead to minor information leaks, and in one case a loop-condition underflow
- a fix of a long-standing regression in the ftdi_sio driver which resulted
in excessive bulk-in interrupts
- a fix for ftdi_sio line-status over-reporting which could lead to an
endless stream of NULL-characters being forwarded to user space
- a fix for a regression in the console driver
- a fix for another mos7840 NULL-pointer dereference due to a missing endpoint
sanity check
Included are also some clean ups and fixes for various minor issues, as well as
a couple of new device IDs that came in late.
All but the final patch have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix another NULL-pointer dereference at open should a malicious device
lack an interrupt-in endpoint.
Note that the driver has a broken check for an interrupt-in endpoint
which means that an interrupt URB has never even been submitted.
Fixes: 3f5429746d ("USB: Moschip 7840 USB-Serial Driver")
Cc: stable <stable@vger.kernel.org> # v2.6.19: 5c75633ef7
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop two redundant NULL checks from usb_serial_console_disconnect().
The usb_serial_console_disconnect function is called from the
USB-serial-device disconnect callback when a device is going away. Hence
there is no need to check for the serial-device pointer being NULL.
The serial-device port pointers are stored in an array that is a member
of the serial struct so the address of the first member of the array
(which the array name decays to) is never NULL either.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Since commit 4a51096937 ("tty: Make tty_files_lock per-tty") a new
tty_struct spin lock is taken in the tty release path, but the
USB-serial-console hack was never updated hence leaving the lock of its
"fake" tty uninitialised. This was eventually detected by lockdep.
Make sure to initialise the new lock also for the fake tty to address
this regression.
Yes, this code is a mess, but cleaning it up is left for another day.
Fixes: 4a51096937 ("tty: Make tty_files_lock per-tty")
Cc: stable <stable@vger.kernel.org> # 4.6
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
No need to reinitialise the interrupt-in URB with values that have not
changed before (some) resubmissions.
This also allows the interrupt-in callback to have a single path for URB
resubmission.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop redundant URB unlink as there's no need to unlink an URB which is
about to be killed synchronously.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Interface numbers do not change when enabling alternate settings as
comment and code in this driver suggested.
Remove the confusing comment and redundant retrieval of the interface
number in probe, while simplifying and renaming the interface-number
helper.
Fixes: 4db2299da2 ("sierra: driver interface blacklisting")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
FTDI devices use a receive latency timer to periodically empty the
receive buffer and report modem and line status (also when the buffer is
empty).
When a break or error condition is detected the corresponding status
flags will be set on a packet with nonzero data payload and the flags
are not updated until the break is over or further characters are
received.
In order to avoid over-reporting break and error conditions, these flags
must therefore only be processed for packets with payload.
This specifically fixes the case where after an overrun, the error
condition is continuously reported and NULL-characters inserted until
further data is received.
Reported-by: Michael Walle <michael@walle.cc>
Fixes: 72fda3ca6f ("USB: serial: ftd_sio: implement sysrq handling on
break")
Fixes: 166ceb6907 ("USB: ftdi_sio: clean up line-status handling")
Cc: stable <stable@vger.kernel.org> # v2.6.35
Signed-off-by: Johan Hovold <johan@kernel.org>
Add new USB IDs for cp2104/5 devices on Bx50v3 boards due to the design
change.
Signed-off-by: Ken Lin <yungching0725@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to check for short transfers before parsing the receive buffer
to avoid acting on stale data.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure the received data has the required headers before parsing it.
Also drop the redundant urb-status check, which has already been handled
by the caller.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to check for short transfers to avoid underflow in a loop
condition when parsing the receive buffer.
Also fix an off-by-one error in the incomplete sanity check which could
lead to invalid data being parsed.
Fixes: 8c209e6782 ("USB: make actual_length in struct urb field u32")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org> # v2.6.30
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Seems that ATEN serial-to-usb devices using pl2303 exist with
different device ids. This patch adds a missing device ID so it
is recognised by the driver.
Signed-off-by: Marcel J.E. Mol <marcel@mesa.nl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use the port device rather than usb device in info and error messages.
This makes sure that driver and tty port is included in the messages,
while also making them more uniform.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove redundant check of num_interrupt_in which has already been
verified in probe (killing a NULL-urb would also have been fine).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Return -ENODEV rather than -EINVAL on probe errors due to a missing
endpoint.
Also clean up the endpoint sanity check somewhat and use the interface
device for logging a more compact error in case an expected endpoint is
missing.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Currently we already have two pin configuration related callbacks
available for GPIO chips .set_single_ended() and .set_debounce(). In
future we expect to have even more, which does not scale well if we need
to add yet another callback to the GPIO chip structure for each possible
configuration parameter.
Better solution is to reuse what we already have available in the
generic pinconf.
To support this, we introduce a new .set_config() callback for GPIO
chips. The callback takes a single packed pin configuration value as
parameter. This can then be extended easily beyond what is currently
supported by just adding new types to the generic pinconf enum.
If the GPIO driver is backed up by a pinctrl driver the GPIO driver can
just assign gpiochip_generic_config() (introduced in this patch) to
.set_config and that will take care configuration requests are directed
to the pinctrl driver.
We then convert the existing drivers over .set_config() and finally
remove the .set_single_ended() and .set_debounce() callbacks.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The adaptor can be found on development boards for 78k, RL78 and V850
microcontrollers produced by Renesas Electronics Corporation.
This is not a full-featured USB to serial converter, however it allows
basic communication and simple control which is enough for programming of
on-board flash and debugging through a debug monitor.
uPD78F0730 is a USB-enabled microcontroller with USB-to-UART conversion
implemented in firmware.
This chip is also present in some debugging adaptors which use it for
USB-to-SPI conversion as well. The present driver doesn't cover SPI,
only USB-to-UART conversion is supported.
Signed-off-by: Maksim Salau <maksim.salau@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Do not report ASYNC_SKIP_TEST or ASYNC_AUTO_IRQ as being set in
TIOCGSERIAL handlers as these flags are not supported and do not really
make any sense for USB serial devices in the first place.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Clean up the ioctl handler and make sure to pass an unsigned-int rather
than serial_struct pointer to the TIOCSERGETLSR helper as this it what
the user argument really is.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Since commit 557aaa7ffa ("ft232: support the ASYNC_LOW_LATENCY
flag") the FTDI driver has been using a receive latency-timer value of
1 ms instead of the device default of 16 ms.
The latency timer is used to periodically empty a non-full receive
buffer, but a status header is always sent when the timer expires
including when the buffer is empty. This means that a two-byte bulk
message is received every millisecond also for an otherwise idle port as
long as it is open.
Let's restore the pre-2009 behaviour which reduces the rate of the
status messages to 1/16th (e.g. interrupt frequency drops from 1 kHz to
62.5 Hz) by not setting ASYNC_LOW_LATENCY by default.
Anyone willing to pay the price for the minimum-latency behaviour should
set the flag explicitly instead using the TIOCSSERIAL ioctl or a tool
such as setserial (e.g. setserial /dev/ttyUSB0 low_latency).
Note that since commit 0cbd81a9f6 ("USB: ftdi_sio: remove
tty->low_latency") the ASYNC_LOW_LATENCY flag has no other effects but
to set a minimal latency timer.
Reported-by: Antoine Aubert <a.aubert@overkiz.com>
Fixes: 557aaa7ffa ("ft232: support the ASYNC_LOW_LATENCY flag")
Cc: stable@vger.kernel.org # v2.6.31: e3e574ad85
Signed-off-by: Johan Hovold <johan@kernel.org>
The Dell DW5570 is a re-branded Sierra Wireless MC8805 which will by
default boot with vid 0x413c and pid 0x81a3. When triggered QDL download
mode, the device switches to pid 0x81a6 and provides the standard TTY
used for firmware upgrade.
Cc: <stable@vger.kernel.org>
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Johan Hovold <johan@kernel.org>
The opticon driver used a control request at open to trigger a CTS
status notification to be sent over the bulk-in pipe. When the driver
was converted to using the generic read implementation, an inverted test
prevented this request from being sent, something which could lead to
TIOCMGET reporting an incorrect CTS state.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 7a6ee2b027 ("USB: opticon: switch to generic read
implementation")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to detect and return an error on zero-length control-message
transfers when reading from the device.
This addresses a potential failure to detect an empty transmit buffer
during close.
Also remove a redundant check for short transfer when sending a command.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to detect short control-message transfers rather than continue
with zero-initialised data when retrieving modem status and during
device initialisation.
Fixes: 52af954599 ("USB: add USB serial ssu100 driver")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to detect short control transfers and return zero on success
when retrieving the modem status.
This fixes the TIOCMGET implementation which since e1ed212d85 ("USB:
spcp8x5: add proper modem-status support") has returned TIOCM_LE on
successful retrieval, and avoids leaking bits from the stack on short
transfers.
This also fixes the carrier-detect implementation which since the above
mentioned commit unconditionally has returned true.
Fixes: e1ed212d85 ("USB: spcp8x5: add proper modem-status support")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to detect short control-message transfers when fetching
modem and line state in open and when retrieving registers.
This specifically makes sure that an errno is returned to user space on
errors in TIOCMGET instead of a zero bitmask.
Also drop the unused getdevice function which also lacked appropriate
error handling.
Fixes: f7a33e608d ("USB: serial: add quatech2 usb to serial driver")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to return an error on zero-length transfers when retrieving
the line settings even if the driver currently ignores the return value.
Also remove a redundant check for short transfer when setting the line
settings.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to detect short transfers when reading a device register.
The modem-status handling had sufficient error checks in place, but move
handling of short transfers into the register accessor function itself
for consistency.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to log an error on short transfers when reading a device
register.
Also clear the provided buffer (which if often an uninitialised
automatic variable) on errors as the driver currently does not bother to
check for errors.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to detect short control-message transfers so that errors are
logged when reading the modem status at open.
Note that while this also avoids initialising the modem status using
uninitialised heap data, these bits could not leak to user space as they
are currently not used.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove code that allocated but never used a buffer during open.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to detect short control-message transfers and log an error
when reading incomplete manufacturer and boot descriptors.
Note that the default all-zero descriptors will now be used after a
short transfer is detected instead of partially initialised ones.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use a dedicated buffer for the DMA transfer and make sure to detect
short transfers to avoid parsing a corrupt descriptor.
Fixes: 6e8cf7751f ("USB: add EPIC support to the io_edgeport driver")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to detect short responses when reading the latency timer to
avoid using stale buffer data.
Note that no heap data would currently leak through sysfs as
ASYNC_LOW_LATENCY is set by default.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to detect short responses when fetching the modem status in
order to avoid parsing uninitialised buffer data and having bits of it
leak to user space.
Note that we still allow for short 1-byte responses.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix open error handling which failed to detect errors when reading the
MSR and LSR registers, something which could lead to the shadow
registers being initialised from errnos.
Note that calling the generic close implementation is sufficient in the
error paths as the interrupt urb has not yet been submitted and the
register updates have not been made.
Fixes: f4c1e8d597 ("USB: ark3116: Make existing functions 16450-aware
and add close and release functions.")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The current implementation failed to detect short transfers, something
which could lead to bits of the uninitialised heap transfer buffer
leaking to user space.
Fixes: 149fc791a4 ("USB: ark3116: Setup some basic infrastructure for
new ark3116 driver.")
Fixes: f4c1e8d597 ("USB: ark3116: Make existing functions 16450-aware
and add close and release functions.")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove unused termios structure from private data that was left by an
earlier purge by commit b1cff285ae ("usb serial: Eliminate bogus ioctl
code").
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Drop redundant packed attribute from the port-settings struct which is
already 1-byte aligned. Also replace __u8 with u8 for the field types as
this is not a structure we share with user space.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove dead and broken code that only served as a reminder to one day
implement modem control.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Replace a couple of dev_info with dev_dbg and remove another.
Also use the port device for logging, and include a radix prefix when
logging the baudrate.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Some CH340 devices appear unable to change the initial LCR settings, so
set a sane 8N1 default during probe to enable basic support for such
devices.
Also drop a redundant LCR read during device initialisation.
Signed-off-by: Johan Hovold <johan@kernel.org>
Rename the line-control-register variable in set_termios to "lcr" and
use u8 type to match the shadow register.
Signed-off-by: Johan Hovold <johan@kernel.org>
Rename the shadow modem-status register currently named "line_status" to
the less confusing "msr".
Also rename the helper function used to parse the interrupt data.
Signed-off-by: Johan Hovold <johan@kernel.org>
The modem-status register was read as part of device configuration at
port_probe and then again at open (and reset-resume). During open (and
reset-resume) the MSR was read before submitting the interrupt URB,
something which could lead to an MSR-change going unnoticed when it
races with open (reset-resume).
Fix this by dropping the redundant reconfiguration of the port at every
open, and only read the MSR after the interrupt URB has been submitted.
Fixes: 664d5df92e ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Signed-off-by: Johan Hovold <johan@kernel.org>
The variable havedata was only being set but never used afterwards.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
A short control transfer would currently fail to be detected, something
which could lead to stale buffer data being used as valid input.
Check for short transfers, and make sure to log any transfer errors.
Note that this also avoids leaking heap data to user space (TIOCMGET)
and the remote device (break control).
Fixes: 6ce7610478 ("USB: Driver for CH341 USB-serial adaptor")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The current implementation failed to detect short transfers when
attempting to read the line state, and also, to make things worse,
logged the content of the uninitialised heap transfer buffer.
Fixes: abf492e7b3 ("USB: kl5kusb105: fix DMA buffers on stack")
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Revert to using direct register writes to set the divisor and
line-control registers.
A recent change switched to using the init vendor command to update
these registers, something which also enabled support for CH341A
devices. It turns out that simply setting bit 7 in the divisor register
is sufficient to support CH341A and specifically prevent data from being
buffered until a full endpoint-size packet (32 bytes) has been received.
Using the init command also had the side-effect of temporarily
deasserting the DTR/RTS signals on every termios change (including
initialisation on open) something which for example could cause problems
in setups where DTR is used to trigger a reset.
Fixes: 4e46c410e0 ("USB: serial: ch341: reinitialize chip on
reconfiguration")
Signed-off-by: Johan Hovold <johan@kernel.org>
A recent change added support for modifying the default line-control
settings, but did not make sure that the modified settings were used as
part of reconfiguration after a device has been reset during resume.
This caused a port that was open before suspend to be unusable until
being closed and reopened.
Fixes: ba781bdf86 ("USB: serial: ch341: add support for parity, frame
length, stop bits")
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix reset-resume handling which failed to resubmit the read and
interrupt URBs, thereby leaving a port that was open before suspend in a
broken state until closed and reopened.
Fixes: 1ded7ea47b ("USB: ch341 serial: fix port number changed after
resume")
Fixes: 2bfd1c96a9 ("USB: serial: ch341: remove reset_resume callback")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Make sure to stop the interrupt URB before returning on errors during
open.
Fixes: 664d5df92e ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The modem-control signals are managed by the tty-layer during open and
should not be asserted prematurely when set_termios is called from
driver open.
Also make sure that the signals are asserted only when changing speed
from B0.
Fixes: 664d5df92e ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The private baud_rate variable is used to configure the port at open and
reset-resume and must never be set to (and left at) zero or reset-resume
and all further open attempts will fail.
Fixes: aa91def41a ("USB: ch341: set tty baud speed according to tty
struct")
Fixes: 664d5df92e ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
DTR and RTS will be asserted by the tty-layer when the port is opened
and deasserted on close (if HUPCL is set). Make sure the initial state
is not-asserted before the port is first opened as well.
Fixes: 664d5df92e ("USB: usb-serial ch341: support for DTR/RTS/CTS")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix NULL-pointer dereference in open() should the device lack the
expected endpoints:
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at spcp8x5_open+0x30/0xd0 [spcp8x5]
Fixes: 619a6f1d14 ("USB: add usb-serial spcp8x5 driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The write URB was being killed using the synchronous interface while
holding a spin lock in close().
Simply drop the lock and busy-flag update, something which would have
been taken care of by the completion handler if the URB was in flight.
Fixes: f7a33e608d ("USB: serial: add quatech2 usb to serial driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix NULL-pointer dereference in open() should a type-0 or type-1 device
lack the expected endpoints:
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at pl2303_open+0x38/0xec [pl2303]
Note that a missing interrupt-in endpoint would have caused open() to
fail.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix NULL-pointer dereference in open() should the device lack the
expected endpoints:
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at oti6858_open+0x30/0x1d0 [oti6858]
Note that a missing interrupt-in endpoint would have caused open() to
fail.
Fixes: 49cdee0ed0 ("USB: oti6858 usb-serial driver (in Nokia CA-42
cable)")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The interrupt URB is killed at final port close since commit
0de9a7024e ("USB: overhaul of mos7840 driver").
Fixes: 0de9a7024e ("USB: overhaul of mos7840 driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix NULL-pointer dereference in open() should the device lack the
expected endpoints:
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
PC is at mos7840_open+0x88/0x8dc [mos7840]
Note that we continue to treat the interrupt-in endpoint as optional for
now.
Fixes: 3f5429746d ("USB: Moschip 7840 USB-Serial Driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Since commit b69578df7e ("USB: usbserial: mos7720: add support for
parallel port on moschip 7715"), the interrupt urb is no longer
submitted at first port open and the endpoint-address initialisation at
port-probe is no longer used.
Signed-off-by: Johan Hovold <johan@kernel.org>
A static usb-serial-driver structure that is used to initialise the
interrupt URB was modified during probe depending on the currently
probed device type, something which could break a parallel probe of a
device of a different type.
Fix this up by overriding the default completion callback for MCS7715
devices in attach() instead. We may want to use two usb-serial driver
instances for the two types later.
Fixes: fb088e335d ("USB: serial: add support for serial port on the
moschip 7715")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Do not submit the interrupt URB until after the parport has been
successfully registered to avoid another use-after-free in the
completion handler when accessing the freed parport private data in case
of a racing completion.
Fixes: b69578df7e ("USB: usbserial: mos7720: add support for parallel
port on moschip 7715")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The interrupt URB was submitted on probe but never stopped on probe
errors. This can lead to use-after-free issues in the completion
handler when accessing the freed usb-serial struct:
Unable to handle kernel paging request at virtual address 6b6b6be7
...
[<bf052e70>] (mos7715_interrupt_callback [mos7720]) from [<c052a894>] (__usb_hcd_giveback_urb+0x80/0x140)
[<c052a894>] (__usb_hcd_giveback_urb) from [<c052a9a4>] (usb_hcd_giveback_urb+0x50/0x138)
[<c052a9a4>] (usb_hcd_giveback_urb) from [<c0550684>] (musb_giveback+0xc8/0x1cc)
Fixes: b69578df7e ("USB: usbserial: mos7720: add support for parallel
port on moschip 7715")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix NULL-pointer dereference at port open if a device lacks the expected
bulk in and out endpoints.
Unable to handle kernel NULL pointer dereference at virtual address 00000030
...
[<bf071c20>] (mos7720_open [mos7720]) from [<bf0490e0>] (serial_port_activate+0x68/0x98 [usbserial])
[<bf0490e0>] (serial_port_activate [usbserial]) from [<c0470ca4>] (tty_port_open+0x9c/0xe8)
[<c0470ca4>] (tty_port_open) from [<bf049d98>] (serial_open+0x48/0x6c [usbserial])
[<bf049d98>] (serial_open [usbserial]) from [<c0469178>] (tty_open+0xcc/0x5cc)
Fixes: 0f64478cbc ("USB: add USB serial mos7720 driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix NULL-pointer dereference in write() should the device lack the
expected interrupt-out endpoint:
Unable to handle kernel NULL pointer dereference at virtual address 00000054
...
PC is at kobil_write+0x144/0x2a0 [kobil_sct]
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Johan Hovold