Allow ACPI to be built without PCI support in place.
Signed-off-by: Sinan Kaya <okaya@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since acpi_os_get_timer() may be called after the timer subsystem has
been suspended, use the jiffies counter instead of ktime_get(). This
patch avoids that the following warning is reported during hibernation:
WARNING: CPU: 0 PID: 612 at kernel/time/timekeeping.c:751 ktime_get+0x116/0x120
RIP: 0010:ktime_get+0x116/0x120
Call Trace:
acpi_os_get_timer+0xe/0x30
acpi_ds_exec_begin_control_op+0x175/0x1de
acpi_ds_exec_begin_op+0x2c7/0x39a
acpi_ps_create_op+0x573/0x5e4
acpi_ps_parse_loop+0x349/0x1220
acpi_ps_parse_aml+0x25b/0x6da
acpi_ps_execute_method+0x327/0x41b
acpi_ns_evaluate+0x4e9/0x6f5
acpi_ut_evaluate_object+0xd9/0x2f2
acpi_rs_get_method_data+0x8f/0x114
acpi_walk_resources+0x122/0x1b6
acpi_pci_link_get_current.isra.2+0x157/0x280
acpi_pci_link_set+0x32f/0x4a0
irqrouter_resume+0x58/0x80
syscore_resume+0x84/0x380
hibernation_snapshot+0x20c/0x4f0
hibernate+0x22d/0x3a6
state_store+0x99/0xa0
kobj_attr_store+0x37/0x50
sysfs_kf_write+0x87/0xa0
kernfs_fop_write+0x1a5/0x240
__vfs_write+0xd2/0x410
vfs_write+0x101/0x250
ksys_write+0xab/0x120
__x64_sys_write+0x43/0x50
do_syscall_64+0x71/0x220
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fixes: 164a08cee1 (ACPICA: Dispatcher: Introduce timeout mechanism for infinite loop detection)
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
References: https://lists.01.org/pipermail/lkp/2018-April/008406.html
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: 4.16+ <stable@vger.kernel.org> # 4.16+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There was a small race when removing the sbshc module where
smbus_alarm() had queued acpi_smbus_callback() for deferred execution
but it hadn't been run yet, so that when it did run hc had been freed
and the module unloaded, resulting in an invalid paging request.
A similar race existed when removing the sbs module with regards to
acpi_sbs_callback() (which is called from acpi_smbus_callback()).
We therefore need to ensure no callbacks are pending or executing before
the cleanups are done and the modules are removed.
Signed-off-by: Ronald Tschalär <ronald@innovation.ch>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Sometimes memory resource may be overlapping with
SystemMemory Operation Region by design, for example if the
memory region is used as a mailbox for communication with a
firmware in the system. One occasion of such mailboxes is
USB Type-C Connector System Software Interface (UCSI).
With regions like that, it is important that the driver is
able to map the memory with the requirements it has. For
example, the driver should be allowed to map the memory as
non-cached memory. However, if the operation region has been
accessed before the driver has mapped the memory, the memory
has been marked as write-back by the time the driver is
loaded. That means the driver will fail to map the memory
if it expects non-cached memory.
To work around the problem, introducing helper that the
drivers can use to temporarily deactivate (unmap)
SystemMemory Operation Regions that overlap with their
IO memory.
Fixes: 8243edf441 ("usb: typec: ucsi: Add ACPI driver")
Cc: stable@vger.kernel.org
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add an architecture specific function to get the address of the RSDP
table. Per default it will just return 0 indicating falling back to
the current mechanism.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: boris.ostrovsky@oracle.com
Cc: lenb@kernel.org
Cc: linux-acpi@vger.kernel.org
Cc: xen-devel@lists.xenproject.org
Link: http://lkml.kernel.org/r/20180219100906.14265-2-jgross@suse.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add functionality to read LPIT table, which provides:
- Sysfs interface to read residency counters via
/sys/devices/system/cpu/cpuidle/low_power_idle_cpu_residency_us
/sys/devices/system/cpu/cpuidle/low_power_idle_system_residency_us
Here the count "low_power_idle_cpu_residency_us" shows the time spent
by CPU package in low power state. This is read via MSR interface,
which points to MSR for PKG C10.
Here the count "low_power_idle_system_residency_us" show the count the
system was in low power state. This is read via MMIO interface. This
is mapped to SLP_S0 residency on modern Intel systems. This residency
is achieved only when CPU is in PKG C10 and all functional blocks are
in low power state.
It is possible that none of the above counters present or anyone of the
counter present or all counters present.
For example: On my Kabylake system both of the above counters present.
After suspend to idle these counts updated and prints:
6916179
6998564
This counter can be read by tools like turbostat to display. Or it can
be used to debug, if modern systems are reaching desired low power state.
- Provides an interface to read residency counter memory address
This address can be used to get the base address of PMC memory
mapped IO. This is utilized by intel_pmc_core driver to print
more debug information.
In addition, to avoid code duplication to read iomem, removed the read of
iomem from acpi_os_read_memory() in osl.c and made a common function
acpi_os_read_iomem(). This new function is used for reading iomem in
in both osl.c and acpi_lpit.c.
Link: http://www.uefi.org/sites/default/files/resources/Intel_ACPI_Low_Power_S0_Idle.pdf
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit ba665dc8e20d9f7730466a659564dd6c557a6cbc
In Linux, para-virtualization implmentation hooks critical register
writes to prevent real hardware operations. This increases divergences
when the sleep registers are cracked in Linux resident ACPICA.
This patch tries to introduce a single OSL to reduce the divergences.
Link: https://github.com/acpica/acpica/commit/ba665dc8
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* acpica:
ACPI / osl: Remove deprecated acpi_get_table_with_size()/early_acpi_os_unmap_memory()
ACPI / osl: Remove acpi_get_table_with_size()/early_acpi_os_unmap_memory() users
ACPICA: Tables: Allow FADT to be customized with virtual address
ACPICA: Tables: Back port acpi_get_table_with_size() and early_acpi_os_unmap_memory() from Linux kernel
* acpi-scan:
ACPI: do not warn if _BQC does not exist
Since all users are cleaned up, remove the 2 deprecated APIs due to no
users.
As a Linux variable rather than an ACPICA variable, acpi_gbl_permanent_mmap
is renamed to acpi_permanent_mmap to have a consistent coding style across
entire Linux ACPI subsystem.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPICA commit cac6790954d4d752a083e6122220b8a22febcd07
This patch back ports Linux acpi_get_table_with_size() and
early_acpi_os_unmap_memory() into ACPICA upstream to reduce divergences.
The 2 APIs are used by Linux as table management APIs for long time, it
contains a hidden logic that during the early stage, the mapped tables
should be unmapped before the early stage ends.
During the early stage, tables are handled by the following sequence:
acpi_get_table_with_size();
parse the table
early_acpi_os_unmap_memory();
During the late stage, tables are handled by the following sequence:
acpi_get_table();
parse the table
Linux uses acpi_gbl_permanent_mmap to distinguish the early stage and the
late stage.
The reasoning of introducing acpi_get_table_with_size() is: ACPICA will
remember the early mapped pointer in acpi_get_table() and Linux isn't able to
prevent ACPICA from using the wrong early mapped pointer during the late
stage as there is no API provided from ACPICA to be an inverse of
acpi_get_table() to forget the early mapped pointer.
But how ACPICA can work with the early/late stage requirement? Inside of
ACPICA, tables are ensured to be remained in "INSTALLED" state during the
early stage, and they are carefully not transitioned to "VALIDATED" state
until the late stage. So the same logic is in fact implemented inside of
ACPICA in a different way. The gap is only that the feature is not provided
to the OSPMs in an accessible external API style.
It then is possible to fix the gap by providing an inverse of
acpi_get_table() from ACPICA, so that the two Linux sequences can be
combined:
acpi_get_table();
parse the table
acpi_put_table();
In order to work easier with the current Linux code, acpi_get_table() and
acpi_put_table() is implemented in a usage counting based style:
1. When the usage count of the table is increased from 0 to 1, table is
mapped and .Pointer is set with the mapping address (VALIDATED);
2. When the usage count of the table is decreased from 1 to 0, .Pointer
is unset and the mapping address is unmapped (INVALIDATED).
So that we can deploy the new APIs to Linux with minimal effort by just
invoking acpi_get_table() in acpi_get_table_with_size() and invoking
acpi_put_table() in early_acpi_os_unmap_memory(). Lv Zheng.
Link: https://github.com/acpica/acpica/commit/cac67909
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are few 'else' keywords which are redundant in
acpi_os_get_root_pointer(). Refactor function to get rid of them.
While here, switch to pr_err() instead of printk(KERN_ERR ...).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is no need to override the error code returned by kstrtoul().
Propagate it directly to the caller.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
acpi_os_vprintf currently always uses a KERN_CONT prefix which may be
followed immediately by a proper KERN_<LEVEL>. Check if the buffer
already has a KERN_<LEVEL> at the start of the buffer and avoid the
unnecessary KERN_CONT.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There was only one use of __initdata_refok and __exit_refok
__init_refok was used 46 times against 82 for __ref.
Those definitions are obsolete since commit 312b1485fb ("Introduce new
section reference annotations tags: __ref, __refdata, __refconst")
This patch removes the following compatibility definitions and replaces
them treewide.
/* compatibility defines */
#define __init_refok __ref
#define __initdata_refok __refdata
#define __exit_refok __ref
I can also provide separate patches if necessary.
(One patch per tree and check in 1 month or 2 to remove old definitions)
[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/1466796271-3043-1-git-send-email-fabf@skynet.be
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
_OSI handling code grows giant and it's time to move them into one file.
This patch collects all _OSI handling code into one single file.
So that we only have the following functions to be used externally:
early_acpi_osi_init(): Used by DMI detections;
acpi_osi_init(): Used to initialize OSI command line settings and install
Linux specific _OSI handler;
acpi_osi_setup(): The API that should be used by the external quirks.
acpi_osi_is_win8(): The API is used by the external drivers to determine
if BIOS supports Win8.
CONFIG_DMI is not useful as stub dmi_check_system() can make everything
stub because of strip.
No functional changes.
Tested-by: Lukas Wunner <lukas@wunner.de>
Tested-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch performs necessary cleanups before moving OSI support to
another file.
1. Change printk into pr_xxx
2. Do not initialize values to 0
3. Do not append additional "return" at the end of the function
4. Remove useless comments which may easily break line breaking rule
After fixing the coding style issues, rename functions to make them looking
like acpi_osi_xxx.
No functional changes.
Tested-by: Lukas Wunner <lukas@wunner.de>
Tested-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch changes "int/unsigned int" to "bool" to simplify the code.
Tested-by: Lukas Wunner <lukas@wunner.de>
Tested-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The following commit always reports positive value when Apple hardware
queries _OSI("Darwin"):
Commit: 7bc5a2bad0
Subject: ACPI: Support _OSI("Darwin") correctly
However since this implementation places the judgement in runtime, it
breaks acpi_osi=!Darwin and cannot return unsupported for _OSI("WinXXX")
invoked before invoking _OSI("Darwin").
This patch fixes the issues by reverting the wrong support and implementing
the default behavior of _OSI("Darwin")/_OSI("WinXXX") on Apple hardware via
DMI matching.
Fixes: 7bc5a2bad0 (ACPI: Support _OSI("Darwin") correctly)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=92111
Reported-and-tested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch introduces acpi_osi=!! so that quirks may use it to revert
acpi_osi=!.
Tested-by: Lukas Wunner <lukas@wunner.de>
Tested-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch cleans up OSI code in osl.c to make osi_linux work for OSI
strings other than "Linux", so it can be re-used for other purposes.
Tested-by: Lukas Wunner <lukas@wunner.de>
Tested-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The order of the _OSI related functionalities is as follows:
acpi_blacklisted()
acpi_dmi_osi_linux()
acpi_osi_setup()
acpi_osi_setup()
acpi_update_interfaces() if "!*"
<<<<<<<<<<<<<<<<<<<<<<<<
parse_args()
__setup("acpi_osi=")
acpi_osi_setup_linux()
acpi_update_interfaces() if "!*"
<<<<<<<<<<<<<<<<<<<<<<<<
acpi_early_init()
acpi_initialize_subsystem()
acpi_ut_initialize_interfaces()
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
acpi_bus_init()
acpi_os_initialize1()
acpi_install_interface_handler(acpi_osi_handler)
acpi_osi_setup_late()
acpi_update_interfaces() for "!"
>>>>>>>>>>>>>>>>>>>>>>>>
acpi_osi_handler()
Since acpi_osi_setup_linux() can override acpi_dmi_osi_linux(), the command
line setting can override the DMI detection. That's why acpi_blacklisted()
is put before __setup("acpi_osi=").
Then we can notice the following wrong invocation order. There are
acpi_update_interfaces() (marked by <<<<) calls invoked before
acpi_ut_initialize_interfaces() (marked by ^^^^). This makes it impossible
to use acpi_osi=!* correctly from OSI DMI table or from the command line.
The use of acpi_osi=!* is meant to disable both ACPICA
(acpi_gbl_supported_interfaces) and Linux specific strings
(osi_setup_entries) while the ACPICA part should have stopped working
because of the order issue.
This patch fixes this issue by moving acpi_update_interfaces() to where
it is invoked for acpi_osi=! (marked by >>>>) as this is ensured to be
invoked after acpi_ut_initialize_interfaces() (marked by ^^^^). Linux
specific strings are still handled in the original place in order to make
the following command line working: acpi_osi=!* acpi_osi="Module Device".
Note that since acpi_osi=!* is meant to further disable linux specific
string comparing to the acpi_osi=!, there is no such use case in our bug
fixing work and hence there is no one using acpi_osi=!* either from the
command line or from the DMI quirks, this issue is just a theoretical
issue.
Fixes: 741d81280a (ACPI: Add facility to remove all _OSI strings)
Cc: 3.12+ <stable@vger.kernel.org> # 3.12+
Tested-by: Lukas Wunner <lukas@wunner.de>
Tested-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch moves acpi_os_table_override() and
acpi_os_physical_table_override() to tables.c.
Along with the mechanisms, acpi_initrd_initialize_tables() is also moved to
tables.c to form a static function. The following functions are renamed
according to this change:
1. acpi_initrd_override() -> renamed to early_acpi_table_init(), which
invokes acpi_table_initrd_init()
2. acpi_os_physical_table_override() -> which invokes
acpi_table_initrd_override()
3. acpi_initialize_initrd_tables() -> renamed to acpi_table_initrd_scan()
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The patch reduces source code differences between the Linux kernel and the
ACPICA upstream so that the linuxized ACPICA 20160212 release can be
applied with reduced human intervention.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[ rjw: White space damage fixes ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds support to install tables from initrd.
If a table in the initrd wasn't used by the override mechanism,
the table would be installed after initializing all RSDT/XSDT
tables.
Link: https://lkml.org/lkml/2014/2/28/368
Reported-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch cleans up the initrd table override code by merging
redundant logics and re-ordering code blocks.
No functional changes.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-scan:
ACPI: Fix white space in a structure definition
ACPI / utils: Add acpi_dev_present()
ACPI / scan: Fix acpi_bus_id_list bookkeeping
ACPI / scan: set status to 0 if _STA failed
* acpi-bus:
ACPI / bus: Show _OSC UUID when _OSC fails
ACPI / bus: Tidy up _OSC error spacing
* acpi-osl:
ACPI / OSL: Add kerneldoc comments to memory mapping functions
* acpi-pm:
ACPI / PM: Support D3 COLD device in old BIOS for ZPODD
Add kerneldoc comments to acpi_os_map_iomem() and acpi_os_unmap_iomem()
and explain why the latter needs the __ref annotation in one of them
(as suggested by Mathias Krause).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mathias Krause <minipli@googlemail.com>
This patch converts AML debugger into a loadable module.
Note that, it implements driver unloading at the level dependent on the
module reference count. Which means if ACPI debugger is being used by a
userspace program, "rmmod acpi_dbg" should result in failure.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds /sys/kernel/debug/acpi/acpidbg, which can be used by
userspace programs to access ACPICA debugger functionalities.
Known issue:
1. IO flush support
acpi_os_notify_command_complete() and acpi_os_wait_command_ready() can
be used by acpi_dbg module to implement .flush() filesystem operation.
While this patch doesn't go that far. It then becomes userspace tool's
duty now to flush old commands before executing new batch mode commands.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The asm-generic changes for 4.4 are mostly a series from Christoph Hellwig
to clean up various abuses of headers in there. The patch to rename the
io-64-nonatomic-*.h headers caused some conflicts with new users, so I
added a workaround that we can remove in the next merge window.
The only other patch is a warning fix from Marek Vasut
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dQKG
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic cleanups from Arnd Bergmann:
"The asm-generic changes for 4.4 are mostly a series from Christoph
Hellwig to clean up various abuses of headers in there. The patch to
rename the io-64-nonatomic-*.h headers caused some conflicts with new
users, so I added a workaround that we can remove in the next merge
window.
The only other patch is a warning fix from Marek Vasut"
* tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: temporarily add back asm-generic/io-64-nonatomic*.h
asm-generic: cmpxchg: avoid warnings from macro-ized cmpxchg() implementations
gpio-mxc: stop including <asm-generic/bug>
n_tracesink: stop including <asm-generic/bug>
n_tracerouter: stop including <asm-generic/bug>
mlx5: stop including <asm-generic/kmap_types.h>
hifn_795x: stop including <asm-generic/kmap_types.h>
drbd: stop including <asm-generic/kmap_types.h>
move count_zeroes.h out of asm-generic
move io-64-nonatomic*.h out of asm-generic
When the system is waiting for GPE/fixed event handler to finish,
it uses acpi_gbl_FADT.sci_interrupt directly as the IRQ number.
However, the remapped IRQ returned by acpi_gsi_to_irq() should be
passed to synchronize_hardirq() instead of it.
Cc: 3.19+ <stable@vger.kernel.org> # 3.19+
Acked-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently when the system is trying to uninstall the ACPI interrupt
handler, it uses acpi_gbl_FADT.sci_interrupt as the IRQ number.
However, the IRQ number that the ACPI interrupt handled is installed
for comes from acpi_gsi_to_irq() and that is the number that should
be used for the handler removal.
Fix this problem by using the mapped IRQ returned from acpi_gsi_to_irq()
as appropriate.
Cc: All applicable <stable@vger.kernel.org>
Acked-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch enables ACPICA debugger files using a configurable
CONFIG_ACPI_DEBUGGER configuration item. Those debugger related code that
was originally masked as ACPI_FUTURE_USAGE now gets unmasked.
Necessary OSL stubs are also added in this patch:
1. acpi_os_readable(): This should be arch specific in Linux, while this
patch doesn't introduce real implementation and a complex mechanism to
allow architecture specific acpi_os_readable() to be implemented to
validate the address. It may be done by future commits.
2. acpi_os_get_line(): This is used to obtain debugger command input. This
patch only introduces a simple KDB concept example in it and the
example should be co-working with the code implemented in
acpi_os_printf(). Since this KDB example won't be compiled unless
ENABLE_DEBUGGER is defined and it seems Linux has already stopped to
use ENABLE_DEBUGGER, thus do not expect it can work properly.
This patch also cleans up all other ACPI_FUTURE_USAGE surroundings
accordingly.
1. Since linkage error can be automatically detected, declaration in the
headers needn't be surrounded by ACPI_FUTURE_USAGE.
So only the following separate exported fuction bodies are masked by
this macro (other exported fucntions may have already been masked at
entire module level via drivers/acpi/acpica/Makefile):
acpi_install_exception_handler()
acpi_subsystem_status()
acpi_get_system_info()
acpi_get_statistics()
acpi_install_initialization_handler()
2. Since strip can automatically zap the no-user functions, functions that
are not marked with ACPI_EXPORT_SYMBOL() needn't get surrounded by
ACPI_FUTURE_USAGE.
So the following function which is not used by Linux kernel now won't
get surrounded by this macro:
acpi_ps_get_name()
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
These are not implementations of default architecture code but helpers
for drivers. Move them to the place they belong to.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Acked-by: Hitoshi Mitake <mitake.hitoshi@lab.ntt.co.jp>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The readq() and writeq() helpers are available in the
asm-generic/io-64-nonatomic-hi-lo.h and asm-generic/io-64-nonatomic-lo-hi.h
headers. Replace custom implementation by the generic helpers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch updates the method tracing facility as the acpi_debug_trace()
API has been updated to allow it to trace AML interpreter execution, the
meanings and the usages of the API parameters are changed due to the
updates.
The new API:
1. Uses ACPI_TRACE_ENABLED flag to indicate the enabling of the tracer;
2. Allows tracer still can be enabled when method name is not specified so
that the AML interpreter execution can be traced without knowing the
method name, which is useful for kernel boot tracing;
3. Supports arbitrary full path name, it doesn't need to be a name related
to an entrance of acpi_evaluate_object().
Note that the sysfs parameters are also updated so that when reading the
attribute files, ACPICA internal settings are returned.
In order to make the sysfs parameters (acpi.trace_state) available during
boot, this patch adds code to bypass ACPICA semaphore/mutex invocations
when acpi mutex utilities haven't been initialized.
This patch doesn't update documentation of method tracing facility, it will
be updated by further patches.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is no need to carry potentially outdated Free Software Foundation
mailing address in file headers since the COPYING file includes it.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This effectively reverts the following three commits:
7bc10388cc ACPI / resources: free memory on error in add_region_before()
0f1b414d19 ACPI / PNP: Avoid conflicting resource reservations
b9a5e5e18f ACPI / init: Fix the ordering of acpi_reserve_resources()
(commit b9a5e5e18f introduced regressions some of which, but not
all, were addressed by commit 0f1b414d19 and commit 7bc10388cc
was a fixup on top of the latter) and causes ACPI fixed hardware
resources to be reserved at the fs_initcall_sync stage of system
initialization.
The story is as follows. First, a boot regression was reported due
to an apparent resource reservation ordering change after a commit
that shouldn't lead to such changes. Investigation led to the
conclusion that the problem happened because acpi_reserve_resources()
was executed at the device_initcall() stage of system initialization
which wasn't strictly ordered with respect to driver initialization
(and with respect to the initialization of the pcieport driver in
particular), so a random change causing the device initcalls to be
run in a different order might break things.
The response to that was to attempt to run acpi_reserve_resources()
as soon as we knew that ACPI would be in use (commit b9a5e5e18f).
However, that turned out to be too early, because it caused resource
reservations made by the PNP system driver to fail on at least one
system and that failure was addressed by commit 0f1b414d19.
That fix still turned out to be insufficient, though, because
calling acpi_reserve_resources() before the fs_initcall stage of
system initialization caused a boot regression to happen on the
eCAFE EC-800-H20G/S netbook. That meant that we only could call
acpi_reserve_resources() at the fs_initcall initialization stage
or later, but then we might just as well call it after the PNP
initalization in which case commit 0f1b414d19 wouldn't be
necessary any more.
For this reason, the changes made by commit 0f1b414d19 are reverted
(along with a memory leak fixup on top of that commit), the changes
made by commit b9a5e5e18f that went too far are reverted too and
acpi_reserve_resources() is changed into fs_initcall_sync, which
will cause it to be executed after the PNP subsystem initialization
(which is an fs_initcall) and before device initcalls (including
the pcieport driver initialization) which should avoid the initial
issue.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=100581
Link: http://marc.info/?t=143092384600002&r=1&w=2
Link: https://bugzilla.kernel.org/show_bug.cgi?id=99831
Link: http://marc.info/?t=143389402600001&r=1&w=2
Fixes: b9a5e5e18f "ACPI / init: Fix the ordering of acpi_reserve_resources()"
Reported-by: Roland Dreier <roland@purestorage.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Fix system resume problems related to 32-bit and 64-bit versions
of the Firmware ACPI Control Structure (FACS) in the firmare (Lv
Zheng).
- Fix double initialization of the FACS (Lv Zheng).
- Add _CLS object processing code to ACPICA (Suravee Suthikulpanit).
- Add support for the (currently missing) new GIC version field in
the Multiple APIC Description Table (MADT) (Hanjun Guo).
- Add support for overriding objects in the ACPI namespace to
ACPICA and OSDT support (Lv Zheng, Bob Moore, Zhang Rui).
- Updates related to the TCPA and TPM2 ACPI tables (Bob Moore).
- Restore the commit modifying _REV to always return "2" (as
required by ACPI 6) and add a blacklisting mechanism for
systems that may be affected by that change (Rafael J Wysocki).
- Assorted fixes and cleanups (Bob Moore, Lv Zheng, Sascha Wildner).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=MlWS
-----END PGP SIGNATURE-----
Merge tag 'acpica-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPICA updates from Rafael Wysocki:
"Additional ACPICA material for v4.2-rc1
This will update the ACPICA code in the kernel to upstream revision
20150619 (a bug-fix release mostly including stable-candidate fixes)
and restore an earlier ACPICA commit that had to be reverted due to a
regression introduced by it (the regression is addressed by
blacklisting the only known system affected by it to date).
The only new feature added by this update is the support for
overriding objects in the ACPI namespace and a new ACPI table that can
be used for that called the Override System Definition Table (OSDT).
That should allow us to "patch" the ACPI namespace built from
incomplete or incorrect ACPI System Definition tables (DSDT, SSDT)
during system startup without the need to provide replacements for all
of those tables in the future.
Specifics:
- Fix system resume problems related to 32-bit and 64-bit versions of
the Firmware ACPI Control Structure (FACS) in the firmare (Lv
Zheng)
- Fix double initialization of the FACS (Lv Zheng)
- Add _CLS object processing code to ACPICA (Suravee Suthikulpanit)
- Add support for the (currently missing) new GIC version field in
the Multiple APIC Description Table (MADT) (Hanjun Guo)
- Add support for overriding objects in the ACPI namespace to ACPICA
and OSDT support (Lv Zheng, Bob Moore, Zhang Rui)
- Updates related to the TCPA and TPM2 ACPI tables (Bob Moore)
- Restore the commit modifying _REV to always return "2" (as required
by ACPI 6) and add a blacklisting mechanism for systems that may be
affected by that change (Rafael J Wysocki)
- Assorted fixes and cleanups (Bob Moore, Lv Zheng, Sascha Wildner)"
* tag 'acpica-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (28 commits)
Revert 'Revert "ACPICA: Permanently set _REV to the value '2'."'
ACPI / init: Make it possible to override _REV
ACPICA: Update version to 20150619
ACPICA: Comment update, no functional change
ACPICA: Update TPM2 ACPI table
ACPICA: Update definitions for the TCPA and TPM2 ACPI tables
ACPICA: Split C library prototypes to new header
ACPICA: De-macroize calls to standard C library functions
ACPI / acpidump: Update acpidump manual
ACPICA: acpidump: Convert the default behavior to dump from /sys/firmware/acpi/tables
ACPICA: acpidump: Allow customized tables to be dumped without accessing /dev/mem
ACPICA: Cleanup output for the ASL Debug object
ACPICA: Update for acpi_install_table memory types
ACPICA: Namespace: Change namespace override to avoid node deletion
ACPICA: Namespace: Add support of OSDT table
ACPICA: Namespace: Add support to allow overriding objects
ACPICA: ACPI 6.0: Add values for MADT GIC version field
ACPICA: Utilities: Add _CLS processing
ACPICA: Add dragon_fly support to unix file mapping file
ACPICA: EFI: Add EFI interface definitions to eliminate dependency of GNU EFI
...
The platform firmware on some systems expects Linux to return "5" as
the supported ACPI revision which makes it expose system configuration
information in a special way.
For example, based on what ACPI exports as the supported revision,
Dell XPS 13 (2015) configures its audio device to either work in HDA
mode or in I2S mode, where the former is supposed to be used on Linux
until the latter is fully supported (in the kernel as well as in user
space).
Since ACPI 6 mandates that _REV should return "2" if ACPI 2 or later
is supported by the OS, a subsequent change will make that happen, so
make it possible to override that on systems where "5" is expected to
be returned for Linux to work correctly one them (such as the Dell
machine mentioned above).
Original-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-video: (38 commits)
ACPI / video: Make acpi_video_unregister_backlight() private
acpi-video-detect: Remove old API
toshiba-acpi: Port to new backlight interface selection API
thinkpad-acpi: Port to new backlight interface selection API
sony-laptop: Port to new backlight interface selection API
samsung-laptop: Port to new backlight interface selection API
msi-wmi: Port to new backlight interface selection API
msi-laptop: Port to new backlight interface selection API
intel-oaktrail: Port to new backlight interface selection API
ideapad-laptop: Port to new backlight interface selection API
fujitsu-laptop: Port to new backlight interface selection API
eeepc-laptop: Port to new backlight interface selection API
dell-wmi: Port to new backlight interface selection API
dell-laptop: Port to new backlight interface selection API
compal-laptop: Port to new backlight interface selection API
asus-wmi: Port to new backlight interface selection API
asus-laptop: Port to new backlight interface selection API
apple-gmux: Port to new backlight interface selection API
acer-wmi: Port to new backlight interface selection API
ACPI / video: Fix acpi_video _register vs _unregister_backlight race
...
* acpi-pm:
ACPI / PM: Add missing pm_generic_complete() invocation
ACPI / PM: Turn power resources on and off in the right order during resume
ACPI / PM: Rework device power management to follow ACPI 6
ACPI / PM: Drop stale comment from acpi_power_transition()
* acpi-apei:
GHES: Make NMI handler have a single reader
GHES: Elliminate double-loop in the NMI handler
GHES: Panic right after detection
GHES: Carve out the panic functionality
GHES: Carve out error queueing in a separate function
* acpi-osl:
ACPI / osl: use same type for acpi_predefined_names values as in definition
* acpi-pci:
ACPI / PCI: remove stale list_head in struct acpi_prt_entry
acpi_osi_is_win8 needs access to acpi_gbl_osi_data which is not exported,
so move it to osl.c. Alternatively we could export acpi_gbl_osi_data but
that seems undesirable.
This allows video_detect.c to be build as a module, besides that
acpi_osi_is_win8() is something which does not really belong in
video_detect.c in the first place.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Sinan Kaya