We surely have SDIO support by now :)
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 7729c7a232 ("mmc: tmio: Provide separate interrupt handlers")
refactored the sdio irq handler and wrongly used the mask for SD irqs,
not for SDIO irqs. This doesn't really matter in practice because both
values keep the only interrupt we are interested in. But still, this is
wrong and wants to be fixed.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add tuning support for use with SDR104 mode
Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
An illegal sequence command error may occur if there is a stopbit or
cmd_index error as well as a CRC error. The correct course of action
is to re-enable IRQs
An illegal sequence data error may occur if there is a CRC or stopbit
error, or underrun. In this case set data->error correctly.
This is in preparation for enabling tuning support which relies on
differentiating between illegal sequence and other errors.
Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
[simon: broken out of a larger patch]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For the r7s72100 SOC, the DATA_PORT register was changed to 32-bits wide.
Therefore a new flag has been created that will allow 32-bit reads/writes
to the DATA_PORT register instead of 16-bit (because 16-bits accesses are
not supported).
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We need to add R1 without CRC support, refactor the bus width routine a
little and extend a quirk check. To support "non-removable;" we need a
workaround which will be hopefully removed when reworking PM soon.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
card_busy is only used/tested on SDHI for R-Car Gen2 and later.
Move it to the SDHI driver, so we can then activate it conditionally
depending on the SDHI type.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In linux/mmc/host.h, mmc_card_is_removable() is already defined.
It should be maintainted more easier than now.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
RCar Gen2 and later implementations of TMIO/SDHI have their own set of
features and additions. FAST_CLK_CHG is just one of them and I see a few
others being added soon. Some may work on older chipsets but this needs
to be tested case by case. Instead of adding a bunch of flags for each
feature, add a global RCar2+ one for now. We can still break out
features if the need arises.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This bit has a different meaning in SDHI and original TMIO. Document
that and use the proper naming.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To prevent confusion, use the virtual u32 CTL_STATUS in card_busy() the
same way as in other parts of this driver.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Looking at the backlogs, I am not the only one who missed that the above
functions do not read u32 from one register, but create a virtual u32
from reading to adjacent u16 registers (which depending on 'bus_shift'
can be up to 8 byte apart). Because this driver supports old hardware
for which we don't have documentation, I first wrongly assumed there was
a variant which had a few u32 registers. Let's give the functions more
descriptive names to make it more obvious what is happening.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no reason to have a public and private header file. Merge them
into a private one, so looking up symbols is less confusing.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Having just one irq handler again, let's include the 'card_status'
function in the main handler which is way more readable. Drop a useless
debug output while here. It should be a dev_dbg in case we ever need it
again.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We removed installation of separate handlers previously, so we can also
remove the separate handlers.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 9250aea76b ("mmc: core: Enable runtime PM management of host
devices"), made some calls to the runtime PM API from the driver
redundant. Especially those which deals with runtime PM reference
counting, so let's remove them.
Cc: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Setting frequency to 0 is not enough, the clock explicitly has to be
disabled. Otherwise voltage switching (which needs SDCLK to be quiet)
fails for various cards.
Because we now do the 'new_clock == 0' check right at the beginning,
the indentation level of the rest of the code can be decreased a little.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Starting the clock is always done after frequency change anyhow, so we can
do it directly after the clock calculation and remove the specific calls.
This is the first part of doing proper clock de-/activation at calculation
time.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Based on work by Shinobu Uehara and Ben Dooks. This adds the voltage
switch operation needed for all UHS-I modes, but not the tuning needed
for SDR-104 which will come later.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently tmio_mmc assumes that the input clock frequency is fixed and
only its own clock divider can be changed. This is not true in the
case of sh_mobile_sdhi; we can use the clock API to change it.
In tmio_mmc:
- Delegate setting of f_min from tmio to the clk_enable operation (if
implemented), as it can be smaller than f_max / 512
- Add an optional clk_update operation called from tmio_mmc_set_clock()
that updates the input clock frequency
- Rename tmio_mmc_clk_update() to tmio_mmc_clk_enable(), to avoid
confusion with the clk_update operation
In sh_mobile_sdhi:
- Make the setting of f_max conditional; it should be set through the
max-frequency property in the device tree in future
- Set f_min based on the input clock's minimum frequency
- Implement the clk_update operation, selecting the best input clock
frequency for the bus frequency that's wanted
sh_mobile_sdhi_clk_update() is loosely based on Kuninori Morimoto's work
in sh_mmcif.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Change the clk_enable operation to take a pointer to the struct
tmio_mmc_host and have it set f_max. For consistency, also change the
clk_disable operation to take a pointer to struct tmio_mmc_host.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE. And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.
Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.
Let's stop pretending that pages in page cache are special. They are
not.
The changes are pretty straight-forward:
- <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};
- page_cache_get() -> get_page();
- page_cache_release() -> put_page();
This patch contains automated changes generated with coccinelle using
script below. For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.
The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.
There are few places in the code where coccinelle didn't reach. I'll
fix them manually in a separate patch. Comments and documentation also
will be addressed with the separate patch.
virtual patch
@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT
@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE
@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK
@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)
@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)
@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rcar2 & 3 docs state that for going to and coming from the 0xff setting,
the clock must first be disabled before the DIV bits are changed.
Instead of tracking this, let's just do this unconditionally.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some of the indentation made the code awful to read. Fix that. Also,
introduce defines instead of magic hex values. Note that this includes
one change: We mask out know 0xff instead of 0x1ff. But 0x100 has always
been the clock enable bit. It doesn't make any sense to set it depending
on the clock calculation. Update copyright notices, too. I'll be working
on those files some more in the future.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
These don't make sense anymore. Since commit 5d60e50054 ("mmc: tmio:
add new TMIO_MMC_HAVE_HIGH_REG flags"), we don't deal with a resource
here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The docs for RCar Gen2 & 3 I have access to, mention delays of 5ms after
stop and 1ms after start. Make it possible to apply these values.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix the problem which timeout occurs at the time of command request with
several cards.
The timeout value was insufficient as a verification of several cards,
so it was changed 5 seconds from 2 seconds.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .multi_io_quirk is implemented under tmio_mmc_data.
It goes to tmio_mmc_host by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .clk_disable is implemented under tmio_mmc_data.
It goes to tmio_mmc_host by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .clk_enable is implemented under tmio_mmc_data.
It goes to tmio_mmc_host by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current .write16_hook is implemented under tmio_mmc_data.
It goes to tmio_mmc_host by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current tmio_mmc driver is using tmio_mmc_data for driver/platform
specific data/callback, and it is needed for tmio_mmc_host_probe()
function. Because of this style, include/linux/mfd/tmio.h header has
tmio driver/framework specific data which is not needed from platform.
This patch adds new tmio_mmc_host_alloc/free() as cleanup preparation.
tmio driver specific data/callback will be implemented in tmio_mmc_host,
and platform specific data/callback will be implemented in tmio_mmc_data
in this cleanup.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As soon as the CD IRQ is requested, it can trigger, since it's an
externally controlled event. If it does, delayed_work host->detect will
be scheduled.
Many host controller probe()s are roughly structured as:
*_probe() {
host = sdhci_pltfm_init();
mmc_of_parse(host->mmc);
rc = sdhci_add_host(host);
if (rc) {
sdhci_pltfm_free();
return rc;
}
In 3.17, CD IRQs can are enabled quite early via *_probe() ->
mmc_of_parse() -> mmc_gpio_request_cd() -> mmc_gpiod_request_cd_irq().
Note that in linux-next, mmc_of_parse() calls mmc_gpio*d*_request_cd()
rather than mmc_gpio_request_cd(), and mmc_gpio*d*_request_cd() doesn't
call mmc_gpiod_request_cd_irq(). However, this issue still exists if
mmc_gpio_request_cd() is called directly before mmc_start_host().
sdhci_add_host() may fail part way through (e.g. due to deferred
probe for a vmmc regulator), and sdhci_pltfm_free() does nothing to
unrequest the CD IRQ nor cancel the delayed_work. sdhci_pltfm_free() is
coded to assume that if sdhci_add_host() failed, then the delayed_work
cannot (or should not) have been triggered.
This can lead to the following with CONFIG_DEBUG_OBJECTS_* enabled, when
kfree(host) is eventually called inside sdhci_pltfm_free():
WARNING: CPU: 2 PID: 6 at lib/debugobjects.c:263 debug_print_object+0x8c/0xb4()
ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x18
The object being complained about is host->detect.
There's no need to request the CD IRQ so early; mmc_start_host() already
requests it. For most SDHCI hosts at least, the typical call path that
does this is: *_probe() -> sdhci_add_host() -> mmc_add_host() ->
mmc_start_host(). Therefore, remove the call to mmc_gpiod_request_cd_irq()
from mmc_gpio_request_cd(). This also matches mmc_gpio*d*_request_cd(),
which already doesn't call mmc_gpiod_request_cd_irq().
However, some host controller drivers call mmc_gpio_request_cd() after
mmc_start_host() has already been called, and assume that this will also
call mmc_gpiod_request_cd_irq(). Update those drivers to explicitly call
mmc_gpiod_request_cd_irq() themselves. Ideally, these drivers should be
modified to move their call to mmc_gpio_request_cd() before their call
to mmc_add_host(). However that's too large a change for stable.
This solves the problem (eliminates the kernel error message above),
since it guarantees that the IRQ can't trigger before mmc_start_host()
is called.
The critical point here is that once sdhci_add_host() calls
mmc_add_host() -> mmc_start_host(), sdhci_add_host() is coded not to
fail. In other words, if there's a chance that mmc_start_host() may have
been called, and CD IRQs triggered, and the delayed_work scheduled,
sdhci_add_host() won't fail, and so cleanup is no longer via
sdhci_pltfm_free() (which doesn't free the IRQ or cancel the work queue)
but instead must be via sdhci_remove_host(), which calls mmc_remove_host()
-> mmc_stop_host(), which does free the IRQ and cancel the work queue.
CC: Russell King <linux@arm.linux.org.uk>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexandre Courbot <acourbot@nvidia.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I spent a couple of days with the driver just hanging due to me forgetting to
specify the external crystal frequency, so that clk_get_rate() returned 0 and
thus the loop in tmio_mmc_set_clock() never ended. I don't think that's an
acceptable behavior, so I suggest that the minimum frequency is checked for 0
in tmio_mmc_host_probe().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Ian Molton <ian.molton@codethink.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Current tmio is using sd_ctrl_read16/write16_rep()
for data transfer.
It works if transfer size was even number,
but, last 1 byte will be ignored if
transfer size was odd number.
This patch adds new tmio_mmc_transfer_data()
and solve this issue.
Tested-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now, tmio_mmc can use .multi_io_quirk callback
instead of MMC_CAP2_NO_MULTI_READ flags.
let's use it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some controller is supporting actual clock on SD_CLK_CTRL :: DIV[7:0].
Renesas SH-Mobile SDHI doesn't support,
but, Renesas R-Car SDHI supports it.
This patch adds new TMIO_MMC_CLK_ACTUAL flag for it.
[Kuninori Morimoto: tidyuped for upstreaming]
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
TMIO clock is set via tmio_mmc_set_clock() -> tmio_mmc_clk_start(),
and SCLKEN bit will be set on tmio_mmc_clk_start().
It is not needed on tmio_mmc_set_clock() function.
The required clock setting will not be able to set
in some clocks without this patch.
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some controllers need to check SD bus status when writing data.
Then, it checks ILL_FUNC bit on SD_INFO2 register,
and this method is controlled via TMIO_MMC_HAS_IDLE_WAIT flags.
Same method is required on tmio_mmc_data_irq() which will
be called after writing data.
Current driver is checking CBSY bit for this purpose,
but, some controllers doesn't have CBSY bit.
This patch checks ILL_FUNC bit instead of CBSY bit
if it has TMIO_MMC_HAS_IDLE_WAIT flags
[Kuninori Morimoto: tidyuped for upstreaming]
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Renesas R-Car SDHI should set reserved bits
on CTL_SDIO_STATUS register when writing.
This patch adds new TMIO_MMC_SDIO_STATUS_QUIRK flags
for this purpose
[Kuninori Morimoto: tidyuped for upstreaming
enabled this flags for all SH-Mobile/R-Car]
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Renesas SDHI has "Multiple Block Transfer Mode" settings
on SD_CMD register which controls CMD12 automatically.
This patch cares it, because
CMD12 is not needed when CMD53 (= SD_IO_RW_EXTENDED)
[Kuninori Morimoto: tidyuped for upstreaming
enabled this flags for all SH-Mobile/R-Car]
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Next card access will be always
error if it didn't clear error status
Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
These library functions aren't used and nor needed, let's remove them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
To give the option for tmio hosts to use the runtime PM callbacks for
CONFIG_PM_SLEEP as well as CONFIG_PM_RUNTIME, move them to CONFIG_PM.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
To make sure we don't receive any spurious IRQs while we are inactive,
mask the IRQs from within the ->runtime_suspend() callback.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add clock gating control as a part of the tmio library functions for
runtime PM.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
An internal power state machine were beeing used to keep ->probe() and
->set_ios() in sync. Especially for handling specific scenarios while
using CONFIG_MMC_CLKGATE. Moreover dependency to CONFIG_MMC_CLKGATE
existed to handle runtime PM properly, which we moves away from here.
By removing the state machine and instead make ->set_ios() rely on the
information provided through the function's in-parameters, the code
becomes significantly simplier.
Additonally as a part of this rework we prepares for making the runtime
PM callbacks responsible of clock gating.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Wolfram Sang