NFSv4 file state-changing functions such as OPEN, CLOSE, LOCK,... are all
labelled with "sequence identifiers" in order to prevent the server from
reordering RPC requests, as this could cause its file state to
become out of sync with the client.
Currently the NFS client code enforces this ordering locally using
semaphores to restrict access to structures until the RPC call is done.
This, of course, only works with synchronous RPC calls, since the
user process must first grab the semaphore.
By dropping semaphores, and instead teaching the RPC engine to hold
the RPC calls until they are ready to be sent, we can extend this
process to work nicely with asynchronous RPC calls too.
This patch adds a new list called "rpc_sequence" that defines the order
of the RPC calls to be sent. We add one such list for each state_owner.
When an RPC call is ready to be sent, it checks if it is top of the
rpc_sequence list. If so, it proceeds. If not, it goes back to sleep,
and loops until it hits top of the list.
Once the RPC call has completed, it can then bump the sequence id counter,
and remove itself from the rpc_sequence list, and then wake up the next
sleeper.
Note that the state_owner sequence ids and lock_owner sequence ids are
all indexed to the same rpc_sequence list, so OPEN, LOCK,... requests
are all ordered w.r.t. each other.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Use schedule_timeout_{,un}interruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size. Also use helper
functions to convert between human time units and jiffies rather than constant
HZ division to avoid rounding errors.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When the client performs an exclusive create and opens the file for writing,
a Netapp filer will first create the file using the mode 01777. It does this
since an NFSv3/v4 exclusive create cannot immediately set the mode bits.
The 01777 mode then gets put into the inode->i_mode. After the file creation
is successful, we then do a setattr to change the mode to the correct value
(as per the NFS spec).
The problem is that nfs_refresh_inode() no longer updates inode->i_mode, so
the latter retains the 01777 mode. A bit later, the VFS notices this, and calls
remove_suid(). This of course now resets the file mode to inode->i_mode & 0777.
Hey presto, the file mode on the server is now magically changed to 0777. Duh...
Fixes http://bugzilla.linux-nfs.org/show_bug.cgi?id=32
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If we do not hold a valid stateid that is open for writes, there is little
point in doing an extra open of the file, as the RFC does not appear to
mandate this...
Make setattr use the correct stateid if we're holding mandatory byte
range locks.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Older gcc's don't like this.
fs/nfs/nfs4proc.c:2194: field `data' has incomplete type
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The Coverity checker noticed that such a simplification was possible.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add nfs4_acl field to the nfs_inode, and use it to cache acls. Only cache
acls of size up to a page. Also prepare for up to a page of acl data even
when the user doesn't pass in a buffer, as when they want to get the acl
length to decide what size buffer to allocate.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Client-side write support for NFSv4 ACLs.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Client-side support for NFSv4 ACLs. Exports the raw xdr code via the
system.nfs4_acl extended attribute. It is up to userspace to decode the acl
(and to provide correctly xdr'd acls on setxattr), and to convert to/from
POSIX ACLs if desired.
This patch provides only the read support.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add {get,set,list}xattr methods for nfs4. The new methods are no-ops, to be
used by subsequent ACL patch.
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
ACL support will require supporting additional inode operations in v4
(getxattr, setxattr, listxattr). This patch allows different protocol versions
to support different inode operations by adding a file_inode_ops to the
nfs_rpc_ops (to match the existing dir_inode_ops).
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Trond Myklebust