Pull networking fixes from David Miller:
1) Provide device string properly for USB i2400m wimax devices, also
don't OOPS when providing firmware string. From Phil Sutter.
2) Add support for sh_eth SH7734 chips, from Nobuhiro Iwamatsu.
3) Add another device ID to USB zaurus driver, from Guan Xin.
4) Loop index start in pool vector iterator is wrong causing MAC to not
get configured in bnx2x driver, fix from Dmitry Kravkov.
5) EQL driver assumes HZ=100, fix from Eric Dumazet.
6) Now that skb_add_rx_frag() can specify the truesize increment
separately, do so in f_phonet and cdc_phonet, also from Eric
Dumazet.
7) virtio_net accidently uses net_ratelimit() not only on the kernel
warning but also the statistic bump, fix from Rick Jones.
8) ip_route_input_mc() uses fixed init_net namespace, oops, use
dev_net(dev) instead. Fix from Benjamin LaHaise.
9) dev_forward_skb() needs to clear the incoming interface index of the
SKB so that it looks like a new incoming packet, also from Benjamin
LaHaise.
10) iwlwifi mistakenly initializes a channel entry as 2GHZ instead of
5GHZ, fix from Stanislav Yakovlev.
11) Missing kmalloc() return value checks in orinoco, from Santosh
Nayak.
12) ath9k doesn't check for HT capabilities in the right way, it is
checking ht_supported instead of the ATH9K_HW_CAP_HT flag. Fix from
Sujith Manoharan.
13) Fix x86 BPF JIT emission of 16-bit immediate field of AND
instructions, from Feiran Zhuang.
14) Avoid infinite loop in GARP code when registering sysfs entries.
From David Ward.
15) rose protocol uses memcpy instead of memcmp in a device address
comparison, oops. Fix from Daniel Borkmann.
16) Fix build of lpc_eth due to dev_hw_addr_rancom() interface being
renamed to eth_hw_addr_random(). From Roland Stigge.
17) Make ipv6 RTM_GETROUTE interpret RTA_IIF attribute the same way
that ipv4 does. Fix from Shmulik Ladkani.
18) via-rhine has an inverted bit test, causing suspend/resume
regressions. Fix from Andreas Mohr.
19) RIONET assumes 4K page size, fix from Akinobu Mita.
20) Initialization of imask register in sky2 is buggy, because bits are
"or'd" into an uninitialized local variable. Fix from Lino
Sanfilippo.
21) Fix FCOE checksum offload handling, from Yi Zou.
22) Fix VLAN processing regression in e1000, from Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
sky2: dont overwrite settings for PHY Quick link
tg3: Fix 5717 serdes powerdown problem
net: usb: cdc_eem: fix mtu
net: sh_eth: fix endian check for architecture independent
usb/rtl8150 : Remove duplicated definitions
rionet: fix page allocation order of rionet_active
via-rhine: fix wait-bit inversion.
ipv6: Fix RTM_GETROUTE's interpretation of RTA_IIF to be consistent with ipv4
net: lpc_eth: Fix rename of dev_hw_addr_random
net/netfilter/nfnetlink_acct.c: use linux/atomic.h
rose_dev: fix memcpy-bug in rose_set_mac_address
Fix non TBI PHY access; a bad merge undid bug fix in a previous commit.
net/garp: avoid infinite loop if attribute already exists
x86 bpf_jit: fix a bug in emitting the 16-bit immediate operand of AND
bonding: emit event when bonding changes MAC
mac80211: fix oper channel timestamp updation
ath9k: Use HW HT capabilites properly
MAINTAINERS: adding maintainer for ipw2x00
net: orinoco: add error handling for failed kmalloc().
net/wireless: ipw2x00: fix a typo in wiphy struct initilization
...
The merge done in commit b26e478f undid bug fix in commit c3e072f8
("net: fsl_pq_mdio: fix non tbi phy access"), with the result that non
TBI (e.g. MDIO) PHYs cannot be accessed.
Signed-off-by: Kenth Eriksson <kenth.eriksson@transmode.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MPC8569 Rev2.0 has the correct SNUM table as QE Reference Manual, we
must follow it.
However the Rev1.0 silicon need the old SNUM table as workaround due to
Rev1.0 silicon SNUM erratum.
So, we support both snum table, and choose the one FDT tell us.
And u-boot will fixup FDT according to SPRN_SVR.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Space allocated for int_name_<foo> is insufficient for
maximal device name, expand it.
Code to create int_name_<foo> is obscure, simplify it
by using sprintf.
Found by looking for unnecessary \ line continuations.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add compatible string for MPC5125 FEC. The FEC on MPC5125 additionally
supports RMII PHY interface. Configure controller/PHY interface type
according to the optional phy-connection-type property in the ethernet
node. This property should be either "rmii" or "mii".
Signed-off-by: Vladimir Ermakov <vooon341@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __netif_subqueue_stopped() just does the following:
struct netdev_queue *txq = netdev_get_tx_queue(dev, queue_index);
return netif_tx_queue_stopped(txq);
and since we already have the txq in scope, we can just call that
directly in this case.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This commit brings the author email address macros up to date for four
modules in the PTP Hardware Clock subsystem.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were two version strings, and neither one was being used.
Also in the same proximity were some unused #define that were
left over from the past. Delete them all.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Add support for byte queue limits (BQL), based on the similar
modifications made to intel/igb/igb_main.c from Eric Dumazet
in commit bdbc063129
"igb: Add support for byte queue limits."
A local variable for tx_queue->qindex was introduced in
gfar_clean_tx_ring, since it is now used often enough to warrant it,
and it cleans up the readability somewhat as well.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Factor out the the existing allocation and free operations
so that they can be used individually.
This is to improve code readability, and also to prepare for
possible future changes like better error recovery and more
dynamic configuration (e.g on-the-fly resizing of the rings).
This change represents a straight up relocation of the existing
code into separate routines without changing any of the contained
code itself. Local variables are relocated as necessary.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.c
Small minor conflict in bnx2x, wherein one commit changed how
statistics were stored in software, and another commit
fixed endianness bugs wrt. reading the values provided by
the chip in memory.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit "391420f7: fec: use an unique MDIO bus name" first modified
the MDIO bus name to include the platform name, then in commit
"a7ed07d5: net: fec: correct phy_name buffer length when init phy_name"
the PHY name formatting was fixed in the case the PHY matches a PHY
driver.
The FEC driver however, also handles the case where we want to attach
to the fixed MDIO bus name, which was previously named "0", and now
"fixed-0". Change the PHY formatting logic to account for that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 21a4e469 (netdev: ethernet dev_alloc_skb to netdev_alloc_skb)
should have used "ndev" instead of "dev".
This causes the following build errors:
drivers/net/ethernet/freescale/fec.c: In function 'fec_enet_rx':
drivers/net/ethernet/freescale/fec.c:714: error: 'dev' undeclared (first use in this function)
drivers/net/ethernet/freescale/fec.c:714: error: (Each undeclared identifier is reported only once
drivers/net/ethernet/freescale/fec.c:714: error: for each function it appears in.)
drivers/net/ethernet/freescale/fec.c: In function 'fec_enet_alloc_buffers':
drivers/net/ethernet/freescale/fec.c:1213: error: 'dev' undeclared (first use in this function)
Fix it, so that fec driver can be built again.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replaced deprecating dev_alloc_skb with netdev_alloc_skb in drivers/net/ethernet
- Removed extra skb->dev = dev after netdev_alloc_skb
Signed-off-by: Pradeep A Dalvi <netdev@pradeepdalvi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the bug that we got wrong phy_name on imx6q sabrelite board.
snprintf used wrong length of phy_name.
phy_name length is MII_BUS_ID_SIZE + 3 rather not MII_BUS_ID_SIZE.
I change it to sizeof(phy_name).
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reorganization of the driver layout in drivers/net
left behind some stale paths in comments and in Kconfig
help text. Bring them up to date. No actual change to
any code takes place here.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using module_platform_driver can make the code smaller.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when the link is 10 Mbps and the mode is RMII, it's necessary
to set FRCONT to 1 in MIIGSK_CFGR to divide the RMII source
clock by 10 in order to support 10 Mbps operations.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When TX time stamping for PTP messages is enabled on a socket, a time
stamp is returned on the socket error queue to the user space application
after the frame was transmitted. The transmitted frame is also returned on
the error queue so that an application knows to which frame the time stamp
belongs.
In the current implementation the TxFCB is immediately followed by the
frame. Since the eTSEC inserts the TX time stamp 8 bytes after the TxFCB,
parts of the frame have been overwritten and an invalid frame was returned
on the socket error queue.
This patch fixes the described problem by adding additional 16 padding
bytes between the TxFCB and the frame for all messages sent from a time
stamping enabled socket (other sockets are not affected).
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there is not enough headroom in the skb a private copy will be made.
However, the private copy had no reference to the socket and consequently
no time stamp could be queued on the socket error queue during the
skb_tstamp_tx function. This patch fixes this issue by also stealing the
sock reference from the original skb after making the private copy.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another simple series related to clock management, this time only for
imx.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=czKE
-----END PGP SIGNATURE-----
Merge tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
clock management changes for i.MX
Another simple series related to clock management, this time only for
imx.
* tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: mxs: select HAVE_CLK_PREPARE for clock
clk: add config option HAVE_CLK_PREPARE into Kconfig
ASoC: mxs-saif: convert to clk_prepare/clk_unprepare
video: mxsfb: convert to clk_prepare/clk_unprepare
serial: mxs-auart: convert to clk_prepare/clk_unprepare
net: flexcan: convert to clk_prepare/clk_unprepare
mtd: gpmi-lib: convert to clk_prepare/clk_unprepare
mmc: mxs-mmc: convert to clk_prepare/clk_unprepare
dma: mxs-dma: convert to clk_prepare/clk_unprepare
net: fec: add clk_prepare/clk_unprepare
ARM: mxs: convert platform code to clk_prepare/clk_unprepare
clk: add helper functions clk_prepare_enable and clk_disable_unprepare
Fix up trivial conflicts in drivers/net/ethernet/freescale/fec.c due to
commit 0ebafefcaa ("net: fec: add clk_prepare/clk_unprepare") clashing
trivially with commit e163cc97f9 ("net/fec: fix the .remove code").
Auditing all usage of ethtool_ops found several drivers that
are not declaring the struct const when it should be.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the driver only uses location values to maintain an ordered
list of filters. Make it reject location values >= MAX_FILER_IDX
passed to the ETHTOOL_SRXCLSRLINS command, consistent with the range
it reports for the ETHTOOL_GRXCLSRLALL command.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Sebastian Pöhn <sebastian.poehn@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If one only selects mx23-based boards, compile fails:
drivers/net/ethernet/freescale/fec.c:410:2: error: 'FEC_HASH_TABLE_HIGH' undeclared (first use in this function)
drivers/net/ethernet/freescale/fec.c:411:2: error: 'FEC_HASH_TABLE_LOW' undeclared (first use in this function)
This is because fec.h uses CONFIG_SOC_IMX28 to determine the register
layout of the core which makes sense since the MX23 does not have a fec.
However, Kconfig uses the broader ARCH_MXS symbol and this way even
makes the fec-driver default for MX23. Adapt Kconfig to use the more
precise SOC_IMX28 as well.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On extensive NFS boots on a mx6qsabrelite board it was noted that "FEC: MDIO read timeout" were occuring,
which caused failure on loading the FEC driver.
The original FEC_MII_TIMEOUT was set to 1 ms, which is too low when passed to the usecs_to_jiffies macro.
On ARM one jiffy is 10ms, so use a timeout of 30ms, which corresponds to 3 jiffies.
After running extensive NFS boots, the MDIO timeouts do not occur anymore with this change.
Signed-off-by: Rogerio Pimentel <rogerio.pimentel@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's for migrating to generic clk framework API.
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
The .remove code is broken in several ways.
- mdiobus_unregister() is called twice for the same object in case of dual FEC
- phy_disconnect() is being called when the PHY is already disconnected
- the requested IRQ(s) are not freed
- fec_stop() is being called with the inteface already stopped
All of those lead to kernel crashes if the remove function is actually used.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Additionally to setting the ETHER_EN bit in FEC_ECNTRL the MII/RMII
setting in FEC_R_CNTRL needs to be preserved to keep the MII interface
functional.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the MAC address is supplied via platform_data it should be OK as
it is and should not be modified in case of a dual FEC setup.
Also copying the MAC from platform_data to the single 'macaddr'
variable will overwrite the MAC for the first interface in case of a
dual FEC setup.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
prevent calling request_irq() with a known invalid IRQ number and
preserve the return value of the platform_get_irq() function
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon detection of a FDX/HDX change the interface is restarted twice.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The con_id is actually not needed for clk_get().
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- remove some bogus whitespace
- remove line wraps from printk messages
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code for setting the address of the internal TBI PHY was
convoluted enough without a maze of ifdefs. Clean it up a bit
so we allow the logic to fail down to -ENODEV at the end of
the if/else ladder, rather than using ifdefs to repeat the same
failure code over and over.
Also, remove the support for the auto-configuration. I'm not aware of
anyone using it, and it ends up using the bus mutex before it's been
initialized.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pdev->id is used in several places for different purpose. All
these uses assume it's always the id of fec device which is >= 0.
However this is only true for non-DT case. When DT plays, pdev->id
is always -1, which will break these pdev->id users.
Instead of fixing all these users one by one, this patch introduces
a new member 'dev_id' to 'struct fec_enet_private' for holding the
correct fec device id, and replaces all the existing uses of pdev->id
with this dev_id.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 230dec6 (net/fec: add imx6q enet support) the FEC driver is no
longer built by default for i.MX SoCs.
Let the FEC driver be built by default again.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the drivers in drivers/net/ethernet/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Pantelis Antoniou <pantelis.antoniou@gmail.com>
Cc: Vitaly Bordug <vbordug@ru.mvista.com>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jiri Pirko <jpirko@redhat.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Richard Cochran <richard.cochran@omicron.at>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Sebastian Poehn <sebastian.poehn@belden.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The semantic patch that makes this change is available
in scripts/coccinelle/api/memdup.cocci.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the number of #defines, use the normal #define from if_ether.h
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the number of #defines, use the normal #define from if_ether.h
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: add couple missing conversions in drivers
split unexporting netdev_fix_features()
implemented %pNF
convert sock::sk_route_(no?)caps
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 952c5ca1 (fsl_pq_mdio: Clean up tbi address configuration) .probe returns
-EBUSY when the "tbi-phy" node is missing. Fix this.
Cc: Andy Fleming <afleming@freescale.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code for setting the address of the internal TBI PHY was
convoluted enough without a maze of ifdefs. Clean it up a bit
so we allow the logic to fail down to -ENODEV at the end of
the if/else ladder, rather than using ifdefs to repeat the same
failure code over and over.
Also, remove the support for the auto-configuration. I'm not aware of
anyone using it, and it ends up using the bus mutex before it's been
initialized.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
forcedeth: fix a few sparse warnings (variable shadowing)
forcedeth: Improve stats counters
forcedeth: remove unneeded stats updates
forcedeth: Acknowledge only interrupts that are being processed
forcedeth: fix race when unloading module
MAINTAINERS/rds: update maintainer
wanrouter: Remove kernel_lock annotations
usbnet: fix oops in usbnet_start_xmit
ixgbe: Fix compile for kernel without CONFIG_PCI_IOV defined
etherh: Add MAINTAINERS entry for etherh
bonding: comparing a u8 with -1 is always false
sky2: fix regression on Yukon Optima
netlink: clarify attribute length check documentation
netlink: validate NLA_MSECS length
i825xx:xscale:8390:freescale: Fix Kconfig dependancies
macvlan: receive multicast with local address
tg3: Update version to 3.121
tg3: Eliminate timer race with reset_task
tg3: Schedule at most one tg3_reset_task run
tg3: Obtain PCI function number from device
...
i825xx and xscale are "sub" Kconfigs to NET_VENDOR_INTEL, so
NET_VENDOR_INTEL should contain ALL the dependencies of the
"sub" Kconfigs.
Same with 8390 is a "sub" Kconfig to NET_VENDOR_NATSEMI, so
NET_VENDOR_NATSEMI needs to contains ALL the dependencies.
Freescale Kconfig only had fs_enet as a sub Kconfig, and already
contained the needed dependencies, just cleaned up the dependencies.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device.h header was including module.h, making it present for
most of these drivers. But we want to clean that up. Call out the
include of module.h in the modular network drivers.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Don't use hardcoded irq num and replace it with
FEC_IRQ_NUM macro.
Signed-off-by: Xiao Jiang <jgq516@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The imx6q enet is a derivative of imx28 enet controller. It fixed
the frame endian issue found on imx28, and added 1 Gbps support.
It also fixes a typo on vendor name in Kconfig.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function fec_enet_mii_init(), it uses non-zero pdev->id as part
of the condition to check the second fec instance (fec1). This works
before the driver supports device tree probe. But in case of device
tree probe, pdev->id is -1 which is also non-zero, so the logic becomes
broken when device tree probe gets supported.
The patch change the logic to check "pdev->id > 0" as the part of the
condition for identifying fec1.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
FEC can work without a phy reset on some platforms, which means not
very platform necessarily have a phy-reset gpio encoded in device tree.
Even on the platforms that have the gpio, FEC can work without
resetting phy for some cases, e.g. boot loader has done that.
So it makes more sense to have the phy-reset-gpio request failure as
a debug message rather than a warning, and get fec_reset_phy() return
void since the caller does not check the return anyway.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A user-space process must use ETHTOOL_GRXCLSRLCNT to find the number
of classification rules, then allocate a buffer of the right size,
then use ETHTOOL_GRXCLSRLALL to fill the buffer. If some other
process inserts or deletes a rule between those two operations,
the user buffer might turn out to be the wrong size.
If it's too small, the return value will be -EMSGSIZE. But if it's
too large, there is no indication of this. Fix this by updating
the rule_cnt field on return.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct the description of ethtool_rxnfc::rule_locs; it is an array
of currently used locations, not all possible valid locations.
Add note that drivers must not use ethtool_rxnfc::rule_locs.
The rule_locs argument to ethtool_ops::get_rxnfc is either NULL or a
pointer to an array of u32, so change the parameter type accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MII Kconfig option is apart of the core networking drivers and
by default NET_CORE is enabled so drivers selecting MII will
have MII enabled as well. It was found using the randconfig
option during testing, MII would be selected but NET_CORE
could be disabled. This caused a dependency error.
Resolved the dependency by selecting NET_CORE when MII is
selected.
Reported-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on finds for Stephen Rothwell, where current defconfig's
enable a ethernet driver and it is not compiled due to the newly
added NET_VENDOR_* component of Kconfig.
This patch enables all the "new" Kconfig options so that current
defconfig's will continue to compile the expected drivers. In
addition, by enabling all the new Kconfig options does not add
any un-expected options.
CC: Stephen Rothwll <sfc@canb.auug.org.au>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Freescale drivers into drivers/net/ethernet/freescale/ and
make the necessary Kconfig and Makefile changes.
CC: Sandeep Gopalpet <sandeep.kumar@freescale.com>
CC: Andy Fleming <afleming@freescale.com>
CC: Shlomi Gridish <gridish@freescale.com>
CC: Li Yang <leoli@freescale.com>
CC: Pantelis Antoniou <pantelis.antoniou@gmail.com>
CC: Vitaly Bordug <vbordug@ru.mvista.com>
CC: Dan Malek <dmalek@jlc.net>
CC: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Richard Cochran