A FTM responder may do PASN authentication with unassociated stations
to allow secure ranging. In this case, the driver will add an internal
station and install the TK so the FW will accept protected FTM
request frames from this station and will send a protected FTM
response frame.
In addition, the driver needs to configure the HLTK to the FW so
the FW can derive the secure LTF bits. This is left for a later
patch since it is not yet supported by the FW.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200911204056.c915b44ad7dd.I72ef7f9753964555561c27ec503241105eddb14e@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Evaluate the appropriate DSM from ACPI to set ETSI SRD 5.8GHz
channels to passive or disabled, default behaviour is enabled.
Add enums and refactor evaluation of DSM functions for better
readablity and more informative debug prints.
Signed-off-by: Gil Adam <gil.adam@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200911204056.816130ee75e0.I727a217be7c967a97960b197a816fc053d10c48a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There is an issue in the HW DMA engine in the 9000 family of devices
when more than 6 RX queues are used. The issue is that the FW may
hang when IWL_MVM_RXQ_NSSN_SYNC notifications are sent.
Fix this by limiting the number of RX queues to 6 in the 9000 family
of devices.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200911204056.37d90f9ceb0c.I8dfe8a7d3a7ac9f0bc9d93e4a03f8165d8c999d2@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In wl3501_detach(), link->priv is checked for a NULL value before being
passed to free_netdev(). However, it cannot be NULL at this point as it
has already been passed to other functions, so just remove the check.
Addresses-Coverity: CID 710499: Null pointer dereferences (REVERSE_INULL)
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200926174558.9436-1-alex.dewar90@gmail.com
Currently if an unsupported iftype is detected the error return path
does not free the cmd_skb leading to a resource leak. Fix this by
free'ing cmd_skb.
Addresses-Coverity: ("Resource leak")
Fixes: 805b28c05c ("qtnfmac: prepare for AP_VLAN interface type support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200925132224.21638-1-colin.king@canonical.com
In the transmit power table, it is important to know what the regulatory
currently is. For different regulatories, there are different
transmit power limits. Show which regulatory the driver is currently
using.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200925061219.23754-6-tehuang@realtek.com
This patch adds a function which is able to dump firmware fifo when
firmware crashes. If firmware needs more than one time to dump all logs,
it will set a bit called "more bit" in the header of the first log, and
driver needs to set a register to inform firmware that it is ready for the
next dump.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200925061219.23754-5-tehuang@realtek.com
Rtw88 currently has a function to dump reserved page section of the
firmware fifo. Reserved page is just part of the firmware fifo, there
are multiple sections in the firmware fifo for different usages, such as
firmware rx fifo and tx fifo.
This commit adds a function to check not only the reserved page section
but also other parts of the firmware fifo. In addition, we need to dump
firmware fifo to dump the debug log message if firmware crashes.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200925061219.23754-4-tehuang@realtek.com
This handles the situation when firmware crashes.
When firmware crashes, it will send an interrupt, and driver will queue
a work for recovery.
In the work, driver will reset it's internal association state, which
includes removing associated sta's macid, resetting vifs' states
and removing keys. After resetting the driver's state, driver will call
rtw_enter_ips() to force the chipset power off to reset the chip.
Finally, driver calls ieee80211_restart_hw() to inform mac80211 stack
to restart.
Since only 8822c firmware supports this feature, the interrupt will only
be triggered when 8822c chipset is loaded.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200925061219.23754-3-tehuang@realtek.com
The vht capability of MAX_MPDU_LENGTH is 11454 in rtw88; however, the rx
buffer size for each packet is 8192. When receiving packets that are
larger than rx buffer size, it will leads to rx buffer ring overflow.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200925061219.23754-2-tehuang@realtek.com
After commit d0186842ec ("net: vlan: Avoid using BUG() in
vlan_proto_idx()"), vlan_proto_idx() was changed to return a signed
integer, however one of its called: vlan_group_prealloc_vid() was still
using an unsigned integer for its return value, fix that.
Fixes: d0186842ec ("net: vlan: Avoid using BUG() in vlan_proto_idx()")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: Update for net-next.
This patch series adds 2 main features to the bnxt_en driver: 200G
link speed support and FEC support with some refactoring of the
link speed logic. The firmware interface is updated to have proper
support for these 2 features. The ethtool preset max channel value
is also adjusted properly to account for XDP and TCs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The current logic that calculates the preset maximum value for combined
channel does not take into account the rings used for XDP and mqprio
TCs. Each of these features will reduce the number of TX rings. Add
the logic to divide the TX rings accordingly based on whether the
device is currently in XDP mode and whether TCs are in use.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This feature allows the user to set the different FEC modes on the NIC
port. Any new setting will take effect immediately after a link toggle.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code is reporting the FEC configured settings during link up.
Change it to report the more useful active FEC encoding that may be
negotiated or auto detected.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement .get_fecparam() method to report the configured and active FEC
settings. Also report the supported and advertised FEC settings to
the .get_link_ksettings() method.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PORT_PHY_CONFIG is always sent with REQ_FLAGS_RESET_PHY set. This flag
must be set in order for the firmware to institute the requested PHY
change immediately, but it results in a link flap. This is unnecessary
and results in an improved user experience if the PHY reconfiguration
is avoided when the user requested speed does not constitute a change.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some 200G dual port NICs, if one port is configured to 200G,
firmware will disable the ethernet link on the other port. Firmware
will send notification to the driver for the disabled port when this
happens. Define a new field in the link_info structure to keep track
of this state. The new phy_state field replaces the unused loop_back
field.
Log a message when the phy_state changes state. In the disabled state,
disallow any PHY configurations on the disabled port as the firmware
will fail all calls to configure the PHY in this state.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool PAM4 link modes for:
50000baseCR_Full
100000baseCR2_Full
200000baseCR4_Full
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware interface has added support for new link speeds using
PAM4 modulation. Expand the bnxt_link_info structure to closely
mirror the new firmware structures. Add logic to copy the PAM4
capabilities and settings from the firmware.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It will be necessary to update more than one field in the link_info
structure when PAM4 speeds are added in a later patch. Instead of
merely translating ethtool speed values to firmware speed values,
change the responsiblity of this function to update all the necessary
link_info fields required to force the speed change to the desired
ethtool value. This also reduces code duplication somewhat at the two
call sites, which otherwise both have to independently update link_info
fields to turn off auto negotiation advertisements.
Also use the appropriate REQ_FORCE_LINK_SPEED definitions. These happen
to have the same values, but req_link_speed is utilimately passed as
force_link_speed in HWRM_PORT_PHY_CFG which is not defined in terms of
REQ_AUTO_LINK_SPEED.
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the code for determining an advertised speed is no longer
supported into a separate function. This will avoid some code
duplication in a later patch when supporting PAM4 speeds, since
these speeds are specified in a separate field.
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The main changes include FEC, ECN statistics, HWRM_PORT_PHY_QCFG
response size reduction, and a new counter added to
ctx_hw_stats_ext struct to support the new 58818 chip.
The ctx_hw_stats_ext structure is now the superset supporting the new
58818 chips and the prior P5 chips. Add a new flag to identify the new
chip and use constants for the chip specific ring statistics sizes
instead of the size of the structure.
Because the HWRM_PORT_PHY_QCFG response structure size has shrunk back
to 96 bytes, the workaround added earlier to limit the size of this
message for forwarding to the VF can be removed.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added the missing stub function for ptp_get_msgtype().
Fixes: 036c508ba9 ("ptp: Add generic ptp message type function")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
rivers/net/ethernet/marvell/mvpp2/mvpp2_main.c:7084:36: warning: ‘mvpp2_acpi_match’ defined but not used [-Wunused-const-variable=]
7084 | static const struct acpi_device_id mvpp2_acpi_match[] = {
| ^~~~~~~~~~~~~~~~
Wrap the definition inside #ifdef/#endif.
Compile tested only.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Expose transceiver overheat counter
Amit says:
An overheated transceiver can be the root cause of various network
problems such as link flapping. Counting the number of times a
transceiver's temperature was higher than its configured threshold can
therefore help in debugging such issues.
This patch set exposes a transceiver overheat counter via ethtool. This
is achieved by configuring the Spectrum ASIC to generate events whenever
a transceiver is overheated. The temperature thresholds are queried from
the transceiver (if available) and set to the default otherwise.
Example:
...
transceiver_overheat: 2
Patch set overview:
Patches #1-#3 add required device registers
Patches #4-#5 add required infrastructure in mlxsw to configure and
count overheat events
Patches #6-#9 gradually add support for the transceiver overheat counter
Patch #10 exposes the transceiver overheat counter via ethtool
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add structures for port statistics which read from core and not directly
from registers.
When netdev's ethtool statistics are queried, query the corresponding
module's overheat counter from core and expose it as
"transceiver_overheat".
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Module temperature warning events are enabled for modules that have a
temperature sensor and configured according to the temperature
thresholds queried from the module.
When a module is unplugged we are guaranteed not to get temperature
warning events. However, when a module is plugged in we need to
potentially update its current settings (i.e., event enablement and
thresholds).
Register to port module plug/unplug events and update module's settings
upon plug in events.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The overheat counter is a per-module counter, but it is exposed as part
of the corresponding netdev's statistics. It should therefore be
presented to user space relative to the netdev's lifetime.
Query the counter just before registering the netdev, so that the value
exposed to user space will be relative to this initial value.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MTWE (Management Temperature Warning Event) is triggered for sensors
whose temperature event enable bit is enabled in the MTMP register.
Enable events for all the modules that have a temperature sensor.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MTWE (Management Temperature Warning Event) is triggered when module's
temperature is higher than its threshold.
Register for MTWE events and increase the module's overheat counter when
its corresponding sensor goes above the configured threshold.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize an array that stores per-module overheat state and a counter
indicating how many times the module was in overheat state.
Export a function to query the counter according to module number.
Will be used later on by the switch driver (i.e., mlxsw_spectrum) to expose
module's overheat counter as part of ethtool statistics.
Initialize mlxsw_env after driver initialization to be able to query
number of modules from MGPIR register.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MTMP register controls various temperature settings on a per-sensor
basis. Subsequent patches are going to alter some of these settings for
sensors found on port modules in response to certain events.
In order to prevent the current callers that write to MTMP from
overriding these settings, have them first query the register and then
change only the relevant register fields.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PMAOS register configures and retrieves the per module status.
The register is used also for enabling event for status change.
It will be used to enable PMPE (Port Module Plug/Unplug) event.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PMPE register reports any operational status change of a module.
It will be used for enabling temperature warning event when a module is
plugged in.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MTWE (Management Temperature Warning Event) register, which is used
for over temperature warning.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan says:
====================
net: hns3: updates for -next
To facilitate code maintenance and compatibility, #1 and #2 add
device version to replace pci revision, #3 to #9 adds support for
querying device capabilities and specifications, then the driver
can use these query results to implement corresponding features
(some features will be implemented later).
And #10 is a minor cleanup since too many parameters for
hclge_shaper_para_calc().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As function hclge_shaper_para_calc() has too many arguments to add
more, so encapsulate its three arguments ir_b, ir_u, ir_s into a
structure.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device specifications querying is unsupported by the old
firmware, in this case, these specifications are 0. However,
some specifications should not be 0 or will cause problem.
So after querying from firmware, some device specifications
are needed to check their value and set to default value if
their values are 0.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The max tm rate is a fixed value(100Gb/s) now as it is defined by a
macro. In order to support other rates in different kinds of device,
it is better to use specification queried from firmware to replace
this macro.
As function hclge_shaper_para_calc() has too many arguments to add
more, so encapsulate its three arguments ir_b, ir_u, ir_s into a
structure.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Golan Ben Ami