Since the display hardware is all there even when INTEL_DISPLAY_ENABLED
return false we have to be capable of shutting it down cleanly so
as to not anger the hw. To that end let's reduce the effect of
!INTEL_DISPLAY_ENABLE to just treating all outputs as disconnected.
Should prevent anyone from automagically enabling any of them, while
still allowing us to cleanly shut them down.
v2: Put the check into the right place for CRT
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200910164256.25983-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
.get_modes() is supposed to return the number of modes added to the
probed_modes list (not that anyone actually checks for anything
except zero vs. not zero). Let's do that. Also switch over to using
intel_connector_update_modes() instead of hand rolling it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200108181242.13650-8-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
With SDVO the pipe config pixel_multiplier only concerns itself with the
data on the SDVO bus. Any HDMI specific pixel repeat must be handled by
the SDVO device itself. To do that simply configure the SDVO pixel
replication factor appropriately. We already set up the infoframe PRB
values correctly via the infoframe helpers.
There is no cap we can check for this. The spec says that 1X,2X,4X are
mandatory, anything else is optional. 1X and 2X are all we need so
we should be able to assume they work.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200108181242.13650-7-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
The SDVO/HDMI port register limited color range bit can only be used
with TMDS encoding and not SDVO encoding, ie. to be used only when
using the port as a HDMI port as opposed to a SDVO port. The SDVO
spec does have a note that some GMCHs might allow that, but gen4
bspec vehemently disagrees. I suppose on ILK+ it might work since
the color range handling is on the CPU side rather than on the PCH
side, so there is no clear linkage between the TMDS vs. SDVO
encoding and color range. Alas, I have no hardware to test that
theory.
To implement limited color range support for SDVO->HDMI we need to
ask the SDVO device to do the range compression. Do so, but first
check if the device even supports the colorimetry selection.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200108181242.13650-5-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
struct drm_device specific drm_WARN* macros include device information
in the backtrace, so we know what device the warnings originate from.
Prefer drm_WARN* over WARN* calls.
changes since v1:
- Added dev_priv local variable and used it in drm_WARN* calls (Jani)
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200504181600.18503-4-pankaj.laxminarayan.bharadiya@intel.com
On TypeC connectors we need to retry the detection after hotplug events
for a longer time, so add a retry counter to support this. The next
patch will add detection retries on TypeC ports needing this.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200330095425.29113-1-imre.deak@intel.com
We're going to want access to the atomic state for iterating
the slave crtcs when enabling the port sync master crtc. Pass
the atomic state all the way down.
The alternative would be yet another encoder hook which we'll
have to call after all the normal modeset stuff is done. Not
really a fan of yet another hook just for this.
Note that during readout state sanitation we are now going
to pass NULL as the atomic state since we don't have one.
We need to change that and then we can also s/crtc_state/crtc/
and s/conn_state/conn/ for the encoder hooks as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200313164831.5980-13-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
The #include has been splattered all over the place, but there are
precious few places, all .c files, that actually need it.
v2: remove leftover double newlines
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200225133131.3301-1-jani.nikula@intel.com
Currently we only set the DRM_CONNECTOR_POLL_{DISCONNECT,CONNECT}
bits in intel_connector->polled (the base setting), leading to
some confusing looking code to reset drm_connector->polled
(the actual setting) to DRM_CONNECTOR_POLL_HPD. Let's set
intel_connector->polled = DRM_CONNECTOR_POLL_HPD for all hpd
capable connectors, and then we don't need so many special
cases in the hotplug code.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200205183546.9291-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Move the force_dvi check to a single function that can be called from
both mode validation and compute_config(). Note that currently we
don't call it from mode validation, but that will change soon.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200108181242.13650-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
The strings we want to print to the on stack buffers should
be no more than
8 * 3 + strlen("(GET_SCALED_HDTV_RESOLUTION_SUPPORT)") + 1 = 61
bytes. So let's shrink the buffers down to 64 bytes.
Also switch the BUG_ON()s to WARN_ON()s if I made a mistake in
my arithmentic.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200108181242.13650-1-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Life is usually easier when we pass around intel_ types instead
of drm_ types. In this case it might not be, but I think being
consistent is a good thing anyway. Also some of this might get
cleaned up a bit more later as we keep propagating the intel_
types further.
@find@
identifier F =~ "^intel_attached_.*";
identifier C;
@@
F(struct drm_connector *C)
{
...
}
@@
identifier find.F;
identifier find.C;
@@
F(
- struct drm_connector *C
+ struct intel_connector *connector
)
{
<...
- C
+ &connector->base
...>
}
@@
identifier find.F;
expression C;
@@
- F(C)
+ F(to_intel_connector(C))
@@
expression C;
@@
- to_intel_connector(&C->base)
+ C
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191204180549.1267-3-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
HDMI_PICTURE_ASPECT_NONE is zero and the connector state is kzalloc()'d
so no need to initialize conn_state->picture_aspect_ratio with it.
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190620142639.17518-6-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
HDMI_PICTURE_ASPECT_NONE means "Automatic" so when the user has that
selected we should keep whatever aspect ratio the mode already has.
Also no point in checking for connector->is_hdmi in the SDVO code
since we only attach the property to HDMI connectors.
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190620142639.17518-5-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Split up crtc_state->base to uapi. This is done using the following patch,
ran after the previous commit that splits out any hw references:
@@
struct intel_crtc_state *T;
@@
-T->base
+T->uapi
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-5-maarten.lankhorst@linux.intel.com
Split up crtc_state->base to hw where appropriate. This is done using the following patch:
@@
struct intel_crtc_state *T;
identifier x =~ "^(active|enable|degamma_lut|gamma_lut|ctm|mode|adjusted_mode)$";
@@
-T->base.x
+T->hw.x
@@
struct drm_crtc_state *T;
identifier x =~ "^(active|enable|degamma_lut|gamma_lut|ctm|mode|adjusted_mode)$";
@@
-to_intel_crtc_state(T)->base.x
+to_intel_crtc_state(T)->hw.x
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191031112610.27608-4-maarten.lankhorst@linux.intel.com
Everything about the file is about display, and mostly about types
related to display. Move under display/ as intel_display_types.h to
reflect the facts.
There's still plenty to clean up, but start off with moving the file
where it logically belongs and naming according to contents.
v2: fix the include guard name in the renamed file
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190806113933.11799-1-jani.nikula@intel.com
There is some scenarios that we are aware that sink probe can fail,
so lets add the infrastructure to let hotplug() hook to request
another probe after some time.
v2: Handle shared HPD pins (Imre)
v3: Rebased
v4: Renamed INTEL_HOTPLUG_NOCHANGE to INTEL_HOTPLUG_UNCHANGED to keep
it consistent(Rodrigo)
v5: Making the working queue used explicit through all the callers to
hotplug_work (Ville)
Tested-by: Timo Aaltonen <tjaalton@ubuntu.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190712005343.24571-1-jose.souza@intel.com
The spec says:
"A value of 0 indicates that this buffer does not exist"
So we should not convert a hbuf_size of 0 into 1.
Also pull the relevant code into a helper to avoid making the
same mistake multiple times.
And while at it fix the debug prints to not say "hbuf_len" twice.
v2: s/%i/%u/ in the debug (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619180312.31817-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
Drop the redundant "SDVO_CMD_" prefix from the command name
strings in sdvo_cmd_names[].
While at it throw away the unused struct name, and undef
SDVO_CMD_NAME_ENTRY() when we're done.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619180312.31817-4-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Use named initializers to make it easier to associate the SDVO debug
prints with the SDVO command defines. Also switch to using ARRAY_SIZE()
instead of assuming that SDVO_CMD_STATUS_SCALING_NOT_SUPP is the last
command type.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619180312.31817-2-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
- HDR support (Uma, Ville)
- Add I2C symlink under HDMI connector similar to DP (Oleg)
- Add ICL multi-segmented gamma support (Shashank, Uma)
- Update register whitelist support for new hardware (Robert, John)
- GuC firmware update with updated ABI interface (Michal, Oscar)
- Add support for new DMC header versions (Lucas)
- In-kernel blitter client for selftest use (Matthew)
- Add Mule Creec Canyon (MCC) PCH support to go with EHL (Matt)
- EHL platform feature updates (Matt)
- Use Command Transport Buffers with GuC on all gens (Daniele)
- New i915.force_probe module parameter to replace i915.alpha_support (Jani)
Refactoring:
- Better runtime PM code abstraction/encapsulation (Daniele)
- VBT parsing cleanup and improvements (Jani)
- Move display code to its own subdirectory (Jani)
- Header cleanup (Jani, Daniele)
- Prep work for subsclice mask expansion (Stuart)
- Use uncore mmio register accessors more, remove unused macro wrappers (Tvrtko)
- Remove unused atomic property get/set stubs (Maarten)
- GTT cleanups and improvements (Mika)
- Pass intel_ types instead of drm_ types in plenty of display code (Ville)
- Engine reset, hangcheck, fault code cleanups and improvements (Tvrtko)
- Consider AML variants simply as either KBL or CFL ULX (Ville)
- State checker cleanups and improvements (Ville)
- GEM code reorganization to more files under gem subdirectory (Chris)
- Reducing dependency on a coarse struct_mutex (Chris)
Fixes:
- Fix use of uninitialized/incorrect error pointers (Colin, Dan)
- Fix DSI fastboot on some VLV/CHV platforms (Hans)
- Fix DSI error path (Hans)
- Add ICL port A combo PHY HW state check (Imre)
- Fix ICL AUX-B HW not done issue (Imre)
- Fix perf whitelist on gen10+ (Lionel)
- Fix PSR exit by forcing manual exit on older gens (José)
- Match voltage ranges instead of exact values (Lucas)
- Fix SDVO HDMI audio, with cleanups (Ville)
- Fix plane state dumps (Ville)
- Fix driver cleanup code to support driver hot unbind (Janusz)
- Add checks for ICL memory bandwidth requirements (Ville)
- Fix toggling between no C8 planes vs. at least one C8 plane (Ville)
- Improved checks on PLL usage conditions, refactoring (Ville)
- Avoid clobbering M/N values in fastset fuzzy checks (Ville)
- Take a runtime pm wakeref for atomic commits (Chris)
- Do not allow runtime pm autosuspend to remove userspace GGTT mmaps too quickly (Chris)
- Avoid refcount_inc on known zero count to avoid debug flagging (Chris)
-----BEGIN PGP SIGNATURE-----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=hS8b
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-next-2019-06-19' of git://anongit.freedesktop.org/drm/drm-intel into drm-next
Features:
- HDR support (Uma, Ville)
- Add I2C symlink under HDMI connector similar to DP (Oleg)
- Add ICL multi-segmented gamma support (Shashank, Uma)
- Update register whitelist support for new hardware (Robert, John)
- GuC firmware update with updated ABI interface (Michal, Oscar)
- Add support for new DMC header versions (Lucas)
- In-kernel blitter client for selftest use (Matthew)
- Add Mule Creec Canyon (MCC) PCH support to go with EHL (Matt)
- EHL platform feature updates (Matt)
- Use Command Transport Buffers with GuC on all gens (Daniele)
- New i915.force_probe module parameter to replace i915.alpha_support (Jani)
Refactoring:
- Better runtime PM code abstraction/encapsulation (Daniele)
- VBT parsing cleanup and improvements (Jani)
- Move display code to its own subdirectory (Jani)
- Header cleanup (Jani, Daniele)
- Prep work for subsclice mask expansion (Stuart)
- Use uncore mmio register accessors more, remove unused macro wrappers (Tvrtko)
- Remove unused atomic property get/set stubs (Maarten)
- GTT cleanups and improvements (Mika)
- Pass intel_ types instead of drm_ types in plenty of display code (Ville)
- Engine reset, hangcheck, fault code cleanups and improvements (Tvrtko)
- Consider AML variants simply as either KBL or CFL ULX (Ville)
- State checker cleanups and improvements (Ville)
- GEM code reorganization to more files under gem subdirectory (Chris)
- Reducing dependency on a coarse struct_mutex (Chris)
Fixes:
- Fix use of uninitialized/incorrect error pointers (Colin, Dan)
- Fix DSI fastboot on some VLV/CHV platforms (Hans)
- Fix DSI error path (Hans)
- Add ICL port A combo PHY HW state check (Imre)
- Fix ICL AUX-B HW not done issue (Imre)
- Fix perf whitelist on gen10+ (Lionel)
- Fix PSR exit by forcing manual exit on older gens (José)
- Match voltage ranges instead of exact values (Lucas)
- Fix SDVO HDMI audio, with cleanups (Ville)
- Fix plane state dumps (Ville)
- Fix driver cleanup code to support driver hot unbind (Janusz)
- Add checks for ICL memory bandwidth requirements (Ville)
- Fix toggling between no C8 planes vs. at least one C8 plane (Ville)
- Improved checks on PLL usage conditions, refactoring (Ville)
- Avoid clobbering M/N values in fastset fuzzy checks (Ville)
- Take a runtime pm wakeref for atomic commits (Chris)
- Do not allow runtime pm autosuspend to remove userspace GGTT mmaps too quickly (Chris)
- Avoid refcount_inc on known zero count to avoid debug flagging (Chris)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87v9x1lpdh.fsf@intel.com
Add a new subdirectory for display code, and start off by moving
modesetting output/encoder code. Judging by the include changes, this is
a surprisingly clean operation.
v2:
- move intel_sdvo_regs.h too
- use tabs for Makefile file lists and sort them
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190613084416.6794-2-jani.nikula@intel.com
Ville Syrjälä