Commit Graph

570 Commits

Author SHA1 Message Date
Vladimir Oltean 52849bcf00 net: mscc: ocelot: avoid overflowing the PTP timestamp FIFO
PTP packets with 2-step TX timestamp requests are matched to packets
based on the egress port number and a 6-bit timestamp identifier.
All PTP timestamps are held in a common FIFO that is 128 entry deep.

This patch ensures that back-to-back timestamping requests cannot exceed
the hardware FIFO capacity. If that happens, simply send the packets
without requesting a TX timestamp to be taken (in the case of felix,
since the DSA API has a void return code in ds->ops->port_txtstamp) or
drop them (in the case of ocelot).

I've moved the ts_id_lock from a per-port basis to a per-switch basis,
because we need separate accounting for both numbers of PTP frames in
flight. And since we need locking to inc/dec the per-switch counter,
that also offers protection for the per-port counter and hence there is
no reason to have a per-port counter anymore.

Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-12 17:35:17 -07:00
Vladimir Oltean c57fe0037a net: mscc: ocelot: make use of all 63 PTP timestamp identifiers
At present, there is a problem when user space bombards a port with PTP
event frames which have TX timestamping requests (or when a tc-taprio
offload is installed on a port, which delays the TX timestamps by a
significant amount of time). The driver will happily roll over the 2-bit
timestamp ID and this will cause incorrect matches between an skb and
the TX timestamp collected from the FIFO.

The Ocelot switches have a 6-bit PTP timestamp identifier, and the value
63 is reserved, so that leaves identifiers 0-62 to be used.

The timestamp identifiers are selected by the REW_OP packet field, and
are actually shared between CPU-injected frames and frames which match a
VCAP IS2 rule that modifies the REW_OP. The hardware supports
partitioning between the two uses of the REW_OP field through the
PTP_ID_LOW and PTP_ID_HIGH registers, and by default reserves the PTP
IDs 0-3 for CPU-injected traffic and the rest for VCAP IS2.

The driver does not use VCAP IS2 to set REW_OP for 2-step timestamping,
and it also writes 0xffffffff to both PTP_ID_HIGH and PTP_ID_LOW in
ocelot_init_timestamp() which makes all timestamp identifiers available
to CPU injection.

Therefore, we can make use of all 63 timestamp identifiers, which should
allow more timestampable packets to be in flight on each port. This is
only part of the solution, more issues will be addressed in future changes.

Fixes: 4e3b0468e6 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-12 17:35:17 -07:00
Jakub Kicinski 9fe1155233 Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
No conflicts.

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-07 15:24:06 -07:00
Dmitry Osipenko 0d7281b27a soc/tegra: pm: Make stubs usable for compile testing
The PM stubs need to depend on ARCH_TEGRA in order to be usable for
compile-testing of tegra-cpuidle driver. Add the dependency.

Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
2021-10-04 21:27:40 +02:00
Dmitry Osipenko aa54686e28 soc/tegra: irq: Add stubs needed for compile testing
Add stubs needed for compile-testing of tegra-cpuidle driver.

Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
2021-10-04 21:27:21 +02:00
Dmitry Osipenko 45e934407b soc/tegra: fuse: Add stubs needed for compile testing
Add stubs needed for compile-testing of tegra-cpuidle driver.

Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
2021-10-04 21:27:04 +02:00
Vladimir Oltean de5bbb6f7e net: mscc: ocelot: support egress VLAN rewriting via VCAP ES0
Currently the ocelot driver does support the 'vlan modify' action, but
in the ingress chain, and it is offloaded to VCAP IS1. This action
changes the classified VLAN before the packet enters the bridging
service, and the bridging works with the classified VLAN modified by
VCAP IS1.

That is good for some use cases, but there are others where the VLAN
must be modified at the stage of the egress port, after the packet has
exited the bridging service. One example is simulating IEEE 802.1CB
active stream identification filters ("active" means that not only the
rule matches on a packet flow, but it is also able to change some
headers). For example, a stream is replicated on two egress ports, but
they must have different VLAN IDs on egress ports A and B.

This seems like a task for the VCAP ES0, but that currently only
supports pushing the ES0 tag A, which is specified in the rule. Pushing
another VLAN header is not what we want, but rather overwriting the
existing one.

It looks like when we push the ES0 tag A, it is actually possible to not
only take the ES0 tag A's value from the rule itself (VID_A_VAL), but
derive it from the following formula:

ES0_TAG_A = Classified VID + VID_A_VAL

Otherwise said, ES0_TAG_A can be used to increment with a given value
the VLAN ID that the packet was already classified to, and the packet
will have this value as an outer VLAN tag. This new VLAN ID value then
gets stripped on egress (or not) according to the value of the native
VLAN from the bridging service.

While the hardware will happily increment the classified VLAN ID for all
packets that match the ES0 rule, in practice this would be rather
insane, so we only allow this kind of ES0 action if the ES0 filter
contains a VLAN ID too, so as to restrict the matching on a known
classified VLAN. If we program VID_A_VAL with the delta between the
desired final VLAN (ES0_TAG_A) and the classified VLAN, we obtain the
desired behavior.

It doesn't look like it is possible with the tc-vlan action to modify
the VLAN ID but not the PCP. In hardware it is possible to leave the PCP
to the classified value, but we unconditionally program it to overwrite
it with the PCP value from the rule.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-02 14:15:57 +01:00
Vladimir Oltean 019d9329e7 net: mscc: ocelot: fix VCAP filters remaining active after being deleted
When ocelot_flower.c calls ocelot_vcap_filter_add(), the filter has a
given filter->id.cookie. This filter is added to the block->rules list.

However, when ocelot_flower.c calls ocelot_vcap_block_find_filter_by_id()
which passes the cookie as argument, the filter is never found by
filter->id.cookie when searching through the block->rules list.

This is unsurprising, since the filter->id.cookie is an unsigned long,
but the cookie argument provided to ocelot_vcap_block_find_filter_by_id()
is a signed int, and the comparison fails.

Fixes: 50c6cc5b92 ("net: mscc: ocelot: store a namespaced VCAP filter ID")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20210930125330.2078625-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-01 15:13:20 -07:00
AngeloGioacchino Del Regno 13e72c3e22 soc: qcom: spm: Implement support for SAWv4.1, SDM630/660 L2 AVS
Implement the support for SAW v4.1, used in at least MSM8998,
SDM630, SDM660 and APQ variants and, while at it, also add the
configuration for the SDM630/660 Silver and Gold cluster L2
Adaptive Voltage Scaler: this is also one of the prerequisites
to allow the OSM controller to perform DCVS.

Please note that despite there are various "versions" of these
values downstream, these are the only ones that are perfectly
stable on the entire set of tested devices.

Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210729155609.608159-4-angelogioacchino.delregno@somainline.org
2021-09-21 17:41:48 -05:00
AngeloGioacchino Del Regno 60f3692b5f cpuidle: qcom_spm: Detach state machine from main SPM handling
In commit a871be6b8e ("cpuidle: Convert Qualcomm SPM driver to a generic
CPUidle driver") the SPM driver has been converted to a
generic CPUidle driver: that was mainly made to simplify the
driver and that was a great accomplishment;
Though, at that time, this driver was only applicable to ARM 32-bit SoCs,
lacking logic about the handling of newer generation SAW.

In preparation for the enablement of SPM features on AArch64/ARM64,
split the cpuidle-qcom-spm driver in two: the CPUIdle related
state machine (currently used only on ARM SoCs) stays there, while
the SPM communication handling lands back in soc/qcom/spm.c and
also making sure to not discard the simplifications that were
introduced in the aforementioned commit.

Since now the "two drivers" are split, the SCM dependency in the
main SPM handling is gone and for this reason it was also possible
to move the SPM initialization early: this will also make sure that
whenever the SAW CPUIdle driver is getting initialized, the SPM
driver will be ready to do the job.

Please note that the anticipation of the SPM initialization was
also done to optimize the boot times on platforms that have their
CPU/L2 idle states managed by other means (such as PSCI), while
needing SAW initialization for other purposes, like AVS control.

Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210729155609.608159-2-angelogioacchino.delregno@somainline.org
2021-09-21 17:41:48 -05:00
Linus Torvalds 866147b8fa ARM: SoC drivers for 5.15
These are updates for drivers that are tied to a particular SoC,
 including the correspondig device tree bindings:
 
  - A couple of reset controller changes for unisoc, uniphier, renesas
    and zte platforms
 
  - memory controller driver fixes for omap and tegra
 
  - Rockchip io domain driver updates
 
  - Lots of updates for qualcomm platforms, mostly touching their
    firmware and power management drivers
 
  - Tegra FUSE and firmware driver updateѕ
 
  - Support for virtio transports in the SCMI firmware framework
 
  - cleanup of ixp4xx drivers, towards enabling multiplatform
    support and bringing it up to date with modern platforms
 
  - Minor updates for keystone, mediatek, omap, renesas.
 
 Signed-off-by: Arnd Bergmann <arnd@arndb.de>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iD8DBQBhLz215t5GS2LDRf4RAjlHAJ473D0PymaTzv68EuPHThG+DEPifQCdGjLq
 QGBB6JidIP8rtEdC+LWBB8I=
 =M5+N
 -----END PGP SIGNATURE-----

Merge tag 'drivers-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC driver updates from Arnd Bergmann:
 "These are updates for drivers that are tied to a particular SoC,
  including the correspondig device tree bindings:

   - A couple of reset controller changes for unisoc, uniphier, renesas
     and zte platforms

   - memory controller driver fixes for omap and tegra

   - Rockchip io domain driver updates

   - Lots of updates for qualcomm platforms, mostly touching their
     firmware and power management drivers

   - Tegra FUSE and firmware driver updateѕ

   - Support for virtio transports in the SCMI firmware framework

   - cleanup of ixp4xx drivers, towards enabling multiplatform support
     and bringing it up to date with modern platforms

   - Minor updates for keystone, mediatek, omap, renesas"

* tag 'drivers-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (96 commits)
  reset: simple: remove ZTE details in Kconfig help
  soc: rockchip: io-domain: Remove unneeded semicolon
  soc: rockchip: io-domain: add rk3568 support
  dt-bindings: power: add rk3568-pmu-io-domain support
  bus: ixp4xx: return on error in ixp4xx_exp_probe()
  soc: renesas: Prefer memcpy() over strcpy()
  firmware: tegra: Stop using seq_get_buf()
  soc/tegra: fuse: Enable fuse clock on suspend for Tegra124
  soc/tegra: fuse: Add runtime PM support
  soc/tegra: fuse: Clear fuse->clk on driver probe failure
  soc/tegra: pmc: Prevent racing with cpuilde driver
  soc/tegra: bpmp: Remove unused including <linux/version.h>
  dt-bindings: soc: ti: pruss: Add dma-coherent property
  soc: ti: Remove pm_runtime_irq_safe() usage for smartreflex
  soc: ti: pruss: Enable support for ICSSG subsystems on K3 AM64x SoCs
  dt-bindings: soc: ti: pruss: Update bindings for K3 AM64x SoCs
  firmware: arm_scmi: Use WARN_ON() to check configured transports
  firmware: arm_scmi: Fix boolconv.cocci warnings
  soc: mediatek: mmsys: Fix missing UFOE component in mt8173 table routing
  soc: mediatek: mmsys: add MT8365 support
  ...
2021-09-01 15:25:28 -07:00
Linus Torvalds 634135a07b ARM: SoC updates for 5.15
There are three noteworthy updates for 32-bit arm platforms this time:
 
  - The Microchip SAMA7 family based on Cortex-A7 gets introduced, a new
    cousin to the older SAM9 (ARM9xx based) and SAMA5 (Cortex-A5 based)
    SoCs.
 
  - The ixp4xx platform (based on Intel XScale) is finally converted to
    device tree, and all the old board files are getting removed now.
 
  - The Cirrus Logic EP93xx platform loses support for the old
    MaverickCrunch FPU. Support for compiling user space applications
    was already removed in gcc-4.9, and the kernel support for old
    applications could not be built with clang ias. After confirming
    that there are no remaining users, removing this from the kernel
    seemed better than adding support for unused features to clang.
 
 There are minor updates to the aspeed, omap and samsung platforms
 
 Signed-off-by: Arnd Bergmann <arnd@arndb.de>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iD8DBQBhL0Bu5t5GS2LDRf4RAtYAAJ9qcN3tF8tHPPBUknXjvQVN7ESntwCfQtPu
 XOVR6q993d7EZh3ATYuXVtE=
 =igP/
 -----END PGP SIGNATURE-----

Merge tag 'soc-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC updates from Arnd Bergmann:
 "There are three noteworthy updates for 32-bit arm platforms this time:

   - The Microchip SAMA7 family based on Cortex-A7 gets introduced, a
     new cousin to the older SAM9 (ARM9xx based) and SAMA5 (Cortex-A5
     based) SoCs.

   - The ixp4xx platform (based on Intel XScale) is finally converted to
     device tree, and all the old board files are getting removed now.

   - The Cirrus Logic EP93xx platform loses support for the old
     MaverickCrunch FPU. Support for compiling user space applications
     was already removed in gcc-4.9, and the kernel support for old
     applications could not be built with clang ias. After confirming
     that there are no remaining users, removing this from the kernel
     seemed better than adding support for unused features to clang.

  There are minor updates to the aspeed, omap and samsung platforms"

* tag 'soc-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits)
  soc: aspeed-lpc-ctrl: Fix clock cleanup in error path
  ARM: s3c: delete unneed local variable "delay"
  soc: aspeed: Re-enable FWH2AHB on AST2600
  soc: aspeed: socinfo: Add AST2625 variant
  soc: aspeed: p2a-ctrl: Fix boundary check for mmap
  soc: aspeed: lpc-ctrl: Fix boundary check for mmap
  ARM: ixp4xx: Delete the Freecom FSG-3 boardfiles
  ARM: ixp4xx: Delete GTWX5715 board files
  ARM: ixp4xx: Delete Coyote and IXDPG425 boardfiles
  ARM: ixp4xx: Delete Intel reference design boardfiles
  ARM: ixp4xx: Delete Avila boardfiles
  ARM: ixp4xx: Delete the Arcom Vulcan boardfiles
  ARM: ixp4xx: Delete Gateway WG302v2 boardfiles
  ARM: ixp4xx: Delete Omicron boardfiles
  ARM: ixp4xx: Delete the D-Link DSM-G600 boardfiles
  ARM: ixp4xx: Delete NAS100D boardfiles
  ARM: ixp4xx: Delete NSLU2 boardfiles
  arm: omap2: Drop the unused OMAP_PACKAGE_* KConfig entries
  arm: omap2: Drop obsolete MACH_OMAP3_PANDORA entry
  ARM: ep93xx: remove MaverickCrunch support
  ...
2021-09-01 15:19:43 -07:00
Vladimir Oltean 3b95d1b293 net: mscc: ocelot: transmit the VLAN filtering restrictions via extack
We need to transmit more restrictions in future patches, convert this
one to netlink extack.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-20 14:39:52 +01:00
Vladimir Oltean 01af940e9b net: mscc: ocelot: transmit the "native VLAN" error via extack
We need to reject some more configurations in future patches, convert
the existing one to netlink extack.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-20 14:39:52 +01:00
Arnd Bergmann c4361dee2e soc/tegra: Changes for v5.15-rc1
Implements runtime PM support for the FUSE block and prepares the driver
 to work better in conjunction with the CPUIDLE driver.
 -----BEGIN PGP SIGNATURE-----
 
 iQJHBAABCAAxFiEEiOrDCAFJzPfAjcif3SOs138+s6EFAmEWl5ATHHRyZWRpbmdA
 bnZpZGlhLmNvbQAKCRDdI6zXfz6zoZsWD/9KuRskoHLU9ism/+4ZW3zb7AthqYEd
 nE0mIjoRjZe8nOjBv4nBO40varyyO5nrA7+Ko5Vu4ArYOz+xFjKVNAYtYe3jqhvv
 fNlvcsMYoAf++3Sr35XjNi6ILQV0eKtZwT5rgLmzcKiC58JZ1y3DMi8YoD3x2MBh
 49O68pG36GjkB6n1fMP/P7KgNmnhfO6AaQCDzxRYxAEKi2whq6jmxcZRIWYaIvPT
 DNTeU7DTFnBYGOmXAyG6qrl6IJKasO6QeU/YXS3XBCwF2XL4cNaWfXawDXm57v4Q
 1G/rz4sUiBLeGoKKqvApuOeogKQpeAfWaZaeYr9wl8OI5yam/kQGcH+qi6kyiLCu
 W7N81RxVWPD2Ehuwn2hdr30Gqq/KtUcY5Dq3YCdP2SwL25fYxbac08FufH/ARPHZ
 MMTo32FhNp+6BYoD5aqFQJAKB0lCDjmZvYPYE1ux/yPysIDSLaVKFCenS0Ky+utA
 UzMUw/IoB2XhTEhgYbrdhcMFcvRTHbldPi6xndSz3RSBcRPLih/5PpKpBmtPPxAc
 TodJVnuIrQCjyQuNKrmlLEyYgbMD6LaX52x8JwLctCNYA/xH7ZXaxCjNXKNshynp
 w4wxGzGNpmTeisvSxin+knjJB8uZu/X9L+wRlzzhs3t6BKwagSJVl0CH5Wviy12P
 WeMvvgV5szk9cw==
 =migJ
 -----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmEdCdsACgkQmmx57+YA
 GNnsexAApw0O9VGU7SCEE9w9drayJNljjaGoOR5HmIq9xgd7IpnGrBsOecVfjTqs
 Z48EB6zELIUrTSaUdfxMM7mF9PSCZyF9ekEl5dA6JeJ+4orvoDHcOOiMmRQxvBrs
 0Sz9q7kCz1N+dabIPym2eOpzfW+EZbGorpadNek1SNAUOTCjPklgIIuXeXAkYWFU
 jak6Fsx3IbG28s8fsaSRDXJSfq40HFOLBlAs0qPykO+iKXYvUHdSrYRn7B8pTHHE
 c2agaS9Hao1+sTUsTTaHEexQRDSNJn31Xae8FQ1o3/Uny+U8fcPKDt9Uy4tcsNi6
 rxS04z4dbm7tVwyasXoqxcwRtKcY4wvhMhniYz80BMAF3DdjsRPYcSmlscDF79aP
 KoeotPXmD6JLnyjmC0SimapQtbdBJsIivTukeuSCxGN7qgYF0YbOmfdlSTU5YtmP
 DXzaAcT6cJaefSSR5IgOxwa2v3LsDTO1HLbuhMtfQL32RaXxFNHjByBz250ltsO7
 2hXTyMSkbo4NFeEdD4+JjmuIMkwh8L25NJDnUKjC5i0cn3568IfktAkxfKj/5qPs
 McI7oriaW//ljUroP7CAxsf+Y+FOIy/Bf9vgpmbCHaKns4xaJCCQc8jMIRzrqeE4
 Y7yiaG5cktceQtLDHvTWZgMgC8FDO1UfFpBFdSYJkjcFbTOxlUk=
 =GgIf
 -----END PGP SIGNATURE-----

Merge tag 'tegra-for-5.15-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/drivers

soc/tegra: Changes for v5.15-rc1

Implements runtime PM support for the FUSE block and prepares the driver
to work better in conjunction with the CPUIDLE driver.

* tag 'tegra-for-5.15-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  soc/tegra: fuse: Enable fuse clock on suspend for Tegra124
  soc/tegra: fuse: Add runtime PM support
  soc/tegra: fuse: Clear fuse->clk on driver probe failure
  soc/tegra: pmc: Prevent racing with cpuilde driver
  soc/tegra: bpmp: Remove unused including <linux/version.h>

Link: https://lore.kernel.org/r/20210813162157.2820913-3-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-08-18 15:23:38 +02:00
Vladimir Oltean e6e12df625 net: mscc: ocelot: convert to phylink
The felix DSA driver, which is a wrapper over the same hardware class as
ocelot, is integrated with phylink, but ocelot is using the plain PHY
library. It makes sense to bring together the two implementations, which
is what this patch achieves.

This is a large patch and hard to break up, but it does the following:

The existing ocelot_adjust_link writes some registers, and
felix_phylink_mac_link_up writes some registers, some of them are
common, but both functions write to some registers to which the other
doesn't.

The main reasons for this are:
- Felix switches so far have used an NXP PCS so they had no need to
  write the PCS1G registers that ocelot_adjust_link writes
- Felix switches have the MAC fixed at 1G, so some of the MAC speed
  changes actually break the link and must be avoided.

The naming conventions for the functions introduced in this patch are:
- vsc7514_phylink_{mac_config,validate} are specific to the Ocelot
  instantiations and placed in ocelot_net.c which is built only for the
  ocelot switchdev driver.
- ocelot_phylink_mac_link_{up,down} are shared between the ocelot
  switchdev driver and the felix DSA driver (they are put in the common
  lib).

One by one, the registers written by ocelot_adjust_link are:

DEV_MAC_MODE_CFG - felix_phylink_mac_link_up had no need to write this
                   register since its out-of-reset value was fine and
                   did not need changing. The write is moved to the
                   common ocelot_phylink_mac_link_up and on felix it is
                   guarded by a quirk bit that makes the written value
                   identical with the out-of-reset one
DEV_PORT_MISC - runtime invariant, was moved to vsc7514_phylink_mac_config
PCS1G_MODE_CFG - same as above
PCS1G_SD_CFG - same as above
PCS1G_CFG - same as above
PCS1G_ANEG_CFG - same as above
PCS1G_LB_CFG - same as above
DEV_MAC_ENA_CFG - both ocelot_adjust_link and ocelot_port_disable
                  touched this. felix_phylink_mac_link_{up,down} also
                  do. We go with what felix does and put it in
                  ocelot_phylink_mac_link_up.
DEV_CLOCK_CFG - ocelot_adjust_link and felix_phylink_mac_link_up both
                write this, but to different values. Move to the common
                ocelot_phylink_mac_link_up and make sure via the quirk
                that the old values are preserved for both.
ANA_PFC_PFC_CFG - ocelot_adjust_link wrote this, felix_phylink_mac_link_up
                  did not. Runtime invariant, speed does not matter since
                  PFC is disabled via the RX_PFC_ENA bits which are cleared.
                  Move to vsc7514_phylink_mac_config.
QSYS_SWITCH_PORT_MODE_PORT_ENA - both ocelot_adjust_link and
                                 felix_phylink_mac_link_{up,down} wrote
                                 this. Ocelot also wrote this register
                                 from ocelot_port_disable. Keep what
                                 felix did, move in ocelot_phylink_mac_link_{up,down}
                                 and delete ocelot_port_disable.
ANA_POL_FLOWC - same as above
SYS_MAC_FC_CFG - same as above, except slight behavior change. Whereas
                 ocelot always enabled RX and TX flow control, felix
                 listened to phylink (for the most part, at least - see
                 the 2500base-X comment).

The registers which only felix_phylink_mac_link_up wrote are:

SYS_PAUSE_CFG_PAUSE_ENA - this is why I am not sure that flow control
                          worked on ocelot. Not it should, since the
                          code is shared with felix where it does.
ANA_PORT_PORT_CFG - this is a Frame Analyzer block register, phylink
                    should be the one touching them, deleted.

Other changes:

- The old phylib registration code was in mscc_ocelot_init_ports. It is
  hard to work with 2 levels of indentation already in, and with hard to
  follow teardown logic. The new phylink registration code was moved
  inside ocelot_probe_port(), right between alloc_etherdev() and
  register_netdev(). It could not be done before (=> outside of)
  ocelot_probe_port() because ocelot_probe_port() allocates the struct
  ocelot_port which we then use to assign ocelot_port->phy_mode to. It
  is more preferable to me to have all PHY handling logic inside the
  same function.
- On the same topic: struct ocelot_port_private :: serdes is only used
  in ocelot_port_open to set the SERDES protocol to Ethernet. This is
  logically a runtime invariant and can be done just once, when the port
  registers with phylink. We therefore don't even need to keep the
  serdes reference inside struct ocelot_port_private, or to use the devm
  variant of of_phy_get().
- Phylink needs a valid phy-mode for phylink_create() to succeed, and
  the existing device tree bindings in arch/mips/boot/dts/mscc/ocelot_pcb120.dts
  don't define one for the internal PHY ports. So we patch
  PHY_INTERFACE_MODE_NA into PHY_INTERFACE_MODE_INTERNAL.
- There was a strategically placed:

	switch (priv->phy_mode) {
	case PHY_INTERFACE_MODE_NA:
	        continue;

  which made the code skip the serdes initialization for the internal
  PHY ports. Frankly that is not all that obvious, so now we explicitly
  initialize the serdes under an "if" condition and not rely on code
  jumps, so everything is clearer.
- There was a write of OCELOT_SPEED_1000 to DEV_CLOCK_CFG for QSGMII
  ports. Since that is in fact the default value for the register field
  DEV_CLOCK_CFG_LINK_SPEED, I can only guess the intention was to clear
  the adjacent fields, MAC_TX_RST and MAC_RX_RST, aka take the port out
  of reset, which does match the comment. I don't even want to know why
  this code is placed there, but if there is indeed an issue that all
  ports that share a QSGMII lane must all be up, then this logic is
  already buggy, since mscc_ocelot_init_ports iterates using
  for_each_available_child_of_node, so nobody prevents the user from
  putting a 'status = "disabled";' for some QSGMII ports which would
  break the driver's assumption.
  In any case, in the eventuality that I'm right, we would have yet
  another issue if ocelot_phylink_mac_link_down would reset those ports
  and that would be forbidden, so since the ocelot_adjust_link logic did
  not do that (maybe for a reason), add another quirk to preserve the
  old logic.

The ocelot driver teardown goes through all ports in one fell swoop.
When initialization of one port fails, the ocelot->ports[port] pointer
for that is reset to NULL, and teardown is done only for non-NULL ports,
so there is no reason to do partial teardowns, let the central
mscc_ocelot_release_ports() do its job.

Tested bind, unbind, rebind, link up, link down, speed change on mock-up
hardware (modified the driver to probe on Felix VSC9959). Also
regression tested the felix DSA driver. Could not test the Ocelot
specific bits (PCS1G, SERDES, device tree bindings).

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-16 11:19:34 +01:00
Vladimir Oltean 46efe4efb9 net: dsa: felix: stop calling ocelot_port_{enable,disable}
ocelot_port_enable touches ANA_PORT_PORT_CFG, which has the following
fields:

- LOCKED_PORTMOVE_CPU, LEARNDROP, LEARNCPU, LEARNAUTO, RECV_ENA, all of
  which are written with their hardware default values, also runtime
  invariants. So it makes no sense to write these during every .ndo_open.

- PORTID_VAL: this field has an out-of-reset value of zero for all ports
  and must be initialized by software. Additionally, the
  ocelot_setup_logical_port_ids() code path sets up different logical
  port IDs for the ports in a hardware LAG, and we absolutely don't want
  .ndo_open to interfere there and reset those values.

So in fact the write from ocelot_port_enable can better be moved to
ocelot_init_port, and the .ndo_open hook deleted.

ocelot_port_disable touches DEV_MAC_ENA_CFG and QSYS_SWITCH_PORT_MODE_PORT_ENA,
in an attempt to undo what ocelot_adjust_link did. But since .ndo_stop
does not get called each time the link falls (i.e. this isn't a
substitute for .phylink_mac_link_down), felix already does better at
this by writing those registers already in felix_phylink_mac_link_down.

So keep ocelot_port_disable (for now, until ocelot is converted to
phylink too), and just delete the felix call to it, which is not
necessary.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-16 11:19:34 +01:00
Dmitry Osipenko 9c93ccfc86 soc/tegra: pmc: Prevent racing with cpuilde driver
Both PMC and cpuidle drivers are probed at the same init level and
cpuidle depends on the PMC suspend mode. Add new default suspend mode
that indicates whether PMC driver has been probed and reset the mode in
a case of deferred probe of the PMC driver.

Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
2021-08-11 11:51:39 +02:00
Arnd Bergmann 318845985f AT91 soc for 5.15:
- add new SoC based on a Cortex-A7 core: the SAMA7G5 family
   - mach-at91 entry, Kconfig and header files
   - Power Management Controller (PMC) code and associated power management
     changes. Support for suspend/resume, Ultra Low Power modes and
     Backup with Memory in Self-Refresh mode.
   - Power management association with DDR controller and
     shutdown controller for addressing this variety of modes.
 -----BEGIN PGP SIGNATURE-----
 
 iHUEABYIAB0WIQQ5TRCVIBiyi/S+BG4fOrpwrNPNDAUCYQpPnQAKCRAfOrpwrNPN
 DJyeAQDvS538E7jFPdsmUn3iZhMhV4zCZVsPk9fox9ptV8ewEAD/QuWFZg78YkZE
 vGe/AXlxjA4V/TMiGElf0/nbZ8xLiw4=
 =YucO
 -----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmEKnQEACgkQmmx57+YA
 GNnU8g/+OZx39NCFnyUcUUmdFHEl/tn6Vkcirs9abdkpjSSylXLJnIVuimHZy0d5
 oxDc3H83dIhCxLO5my27y8QH5e41dhCD7gVIxf+MF/RCYzGt+BjXiImt6YTOvrK9
 hEFzO49XkiBSTtXpNER6hk5BWuIVAg4b1bFnzrhH9ajGxMCboubsxuRMlRP7t4ad
 Vg8Rgf4TOY1AgMm6P5zVjjMAij4C3uKcOO8WLZA9zVGFlKdftdDCvYBfojitctho
 O97Hg4tSYb4N+l8UPcD+dIie0L7Pp8QtgNjV2MiT/Nyuhewdf1DyH14cFSNxIrmA
 laVeRU5WPXJwxNdnEYukb1yI6TEKFQDHTksGWkHr0cQkxalHhuegNUczVwHgZaEZ
 j6pk1yskhRtqmwMyt/810lrEB/o01aPX2TldGda3h3XUxe4q/mw4QR7j9fIFDzjY
 06S5LH/kL36kJ7QAV6ppQLFjBJ5+UJFHymHSXnsCNnaeD6mSZxncaLDoNt+O90kE
 IdALvvwq1ggbKDTQVgpIyU1XfYaNdXcbX1hACXP2LO5/MQejgQ2KJNtS1Qk1aLCC
 T161nfyi/YW5o7h70JGpNK9go5lj/60MgGtocQ5d+zxzyUKNCARaiYRjy0xP7/KR
 1eftv0qgk+J+3+NYOGroLaixVbfLWlIjD9hyaMDnGKzYB857nSY=
 =+KcA
 -----END PGP SIGNATURE-----

Merge tag 'at91-soc-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/soc

AT91 soc for 5.15:

- add new SoC based on a Cortex-A7 core: the SAMA7G5 family
  - mach-at91 entry, Kconfig and header files
  - Power Management Controller (PMC) code and associated power management
    changes. Support for suspend/resume, Ultra Low Power modes and
    Backup with Memory in Self-Refresh mode.
  - Power management association with DDR controller and
    shutdown controller for addressing this variety of modes.

* tag 'at91-soc-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux: (26 commits)
  ARM: at91: pm: add sama7g5 shdwc
  ARM: at91: pm: add pm support for SAMA7G5
  ARM: at91: sama7: introduce sama7 SoC family
  ARM: at91: pm: add sama7g5's pmc
  ARM: at91: pm: add backup mode support for SAMA7G5
  ARM: at91: pm: save ddr phy calibration data to securam
  ARM: at91: pm: add sama7g5 ddr phy controller
  ARM: at91: pm: add sama7g5 ddr controller
  ARM: at91: pm: wait for ddr power mode off
  ARM: at91: pm: add support for 2.5V LDO regulator control
  ARM: at91: pm: add support for MCK1..4 save/restore for ulp modes
  ARM: at91: pm: add self-refresh support for sama7g5
  ARM: at91: ddr: add registers definitions for sama7g5's ddr
  ARM: at91: sfrbu: add sfrbu registers definitions for sama7g5
  ARM: at91: pm: add support for waiting MCK1..4
  ARM: at91: pm: s/CONFIG_SOC_SAM9X60/CONFIG_HAVE_AT91_SAM9X60_PLL/g
  ARM: at91: pm: avoid push and pop on stack while memory is in self-refersh
  ARM: at91: pm: use r7 instead of tmp1
  ARM: at91: pm: do not initialize pdev
  ARM: at91: pm: check for different controllers in at91_pm_modes_init()
  ...

Link: https://lore.kernel.org/r/20210804084316.12641-1-nicolas.ferre@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-08-04 15:58:25 +02:00
Claudiu Beznea d8c7983f31 ARM: at91: ddr: add registers definitions for sama7g5's ddr
Add registers and bits definitions for SAMA7G5's UDDRC and DDR3PHY.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-12-claudiu.beznea@microchip.com
2021-07-19 14:32:12 +02:00
Claudiu Beznea 96abf16861 ARM: at91: sfrbu: add sfrbu registers definitions for sama7g5
Add SFRBU registers definitions for SAMA7G5.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210415105010.569620-11-claudiu.beznea@microchip.com
2021-07-19 14:32:12 +02:00
Arnd Bergmann b6e473d1e2 Memory controller drivers for v5.14 - Tegra SoC, late fixes
Two fixes for recent series of changes in Tegra SoC memory controller
 drivers:
 1. Add a stub for tegra_mc_probe_device() to fix compile testing of
    arm-smmu without TEGRA_MC.
 2. Fix arm-smmu dtschema syntax.
 -----BEGIN PGP SIGNATURE-----
 
 iQJEBAABCgAuFiEE3dJiKD0RGyM7briowTdm5oaLg9cFAmDtUZoQHGtyemtAa2Vy
 bmVsLm9yZwAKCRDBN2bmhouD1/yVD/94mEVxoVOlE/y7gPmvx2HujMOGLWgD8UqS
 sMjXkDun8dJNlFk5dwR/qeS/VWZd8qyyKSiKMV0niD+F7EYtrWxLBqaKDXvNo2IG
 8IXP7O/oCcMpSSjutlqL5vw71FhIdjlIXKr+s7T33wPiBIcLUlbx/9v4SaI6W+1l
 FbNbEk1iL1hvQsgR5U90GXjUhgp4iM3MzlEQKdmufoNSVTUrj/W2RZXOVf0S9BKr
 6R3nJgcHKZS5iwESF2A37/lO6sI04CZwbu0KQEr3mGD0EX9RfZVGhY2bqIZfYQws
 iOn7nRbKYpwEldMhe4qvSWxyS8A4JanXL6sSeBI1X0RiRr+P1u4HRcNQlVYG06gr
 bwBUUzSg1utlC6ERipwjcwIEDt+61GVDP7HMWd0w4xnchdnD8h5BLMqksaeg5vcC
 lsfPyjTNP2DWTj1AYhG9JSRgFYp5YkjBJ7BnzBgHDsXDHIgSknf+zlFVj/9NBESn
 aTE28pZQ3RW55azOnACV6+l42LSoVc8vNWWXRe1jgy60sN7RFe5/Wxb/nQ6qQI1r
 deS9paowkAgz8ojGZqNXkGl7Bq0YE6ZV2XvnlbcU6CFeMbrdK1FfZ9HKcG2nVvhM
 KP1CO1LghUKbr83qN146PsJsH97PKvP4KitSVx3Nby1j/LH8AruBjnx+Ze++rvcU
 rkZXIKZ6qg==
 =V/ST
 -----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmDx8TUACgkQmmx57+YA
 GNnICg/9FDlqHon2H5A6zWqtD0VVp9IH82+9YqgKmtqqARpUre7lLSghdMLbYsor
 5oQlUyk5GbR2VSj5uPs7RNhOvAjPryUm+RwboKEGI+K1l/qOAe7eRIem3w0ZzaYX
 2LLmFjgnIqOMKsBiJGL0PKZTMTW6t4wE7yKJVcyLEPEQ4H7YbUY0U/9X0NVdRmzD
 wfQjcqEbzhKbdYhVxgyoSbw5oE16DhSNY2X4MSMoaUGn0A6SwNYrW8dnpW76ZBRv
 yVPUZilRrfiSwf4qOHlQuEm60Gpa1ndZzbOdlyMhnfqorph1Joe+tezXfdjjG4Vg
 MPxbA2xaYiX2aRUqGomr5jsUNDEKSocRCYgXV9h9jt+TaGANW/u1WMWcqdp9nLND
 hbu9+8bUWd2qyE4XmT9NUJXSb11ccHTNJvEAbanH7JspedhHKya+G0t59vLvyYey
 dbtznkYMhl3y1q/FJl5RLU1yLjmnv3X7Qp9Cj3N1EBySaZxfKynFX1ErqXw7D6dv
 ZnENDVoybFH9D/ZVX+fAiUZkNFfWOV0draVK0122ZwB9NxHvHKwT4JiP58w70UUn
 Qf9LUrdupsILuLoCuQl/P3/uS6xYv8qAnRaLmqGT//NJCq+NINOLCVg1TqI/LWSr
 +m6/HBpPjIrMrsxMWQeC+eJVsbkT6zLXOJKTzhljWVYGHQLGYi4=
 =KdqU
 -----END PGP SIGNATURE-----

Merge tag 'memory-controller-drv-tegra-5.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl into arm/fixes

Memory controller drivers for v5.14 - Tegra SoC, late fixes

Two fixes for recent series of changes in Tegra SoC memory controller
drivers:
1. Add a stub for tegra_mc_probe_device() to fix compile testing of
   arm-smmu without TEGRA_MC.
2. Fix arm-smmu dtschema syntax.

* tag 'memory-controller-drv-tegra-5.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
  dt-bindings: arm-smmu: Fix json-schema syntax
  memory: tegra: Add compile-test stub for tegra_mc_probe_device()

Link: https://lore.kernel.org/r/20210625073604.13562-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-07-16 22:51:01 +02:00
Linus Torvalds 071e5aceeb ARM: Drivers for 5.14
- Reset controllers: Adding support for Microchip Sparx5 Switch.
 
 - Memory controllers: ARM Primecell PL35x SMC memory controller
   driver cleanups and improvements.
 
 - i.MX SoC drivers: Power domain support for i.MX8MM and i.MX8MN.
 
 - Rockchip: RK3568 power domains support + DT binding updates,
   cleanups.
 
 - Qualcomm SoC drivers: Amend socinfo with more SoC/PMIC details,
   including support for MSM8226, MDM9607, SM6125 and SC8180X.
 
 - ARM FFA driver: "Firmware Framework for ARMv8-A", defining
   management interfaces and communication (including bus model)
   between partitions both in Normal and Secure Worlds.
 
 - Tegra Memory controller changes, including major rework to deal
   with identity mappings at boot and integration with ARM SMMU
   pieces.
 -----BEGIN PGP SIGNATURE-----
 
 iQJDBAABCgAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAmDokgYPHG9sb2ZAbGl4
 b20ubmV0AAoJEIwa5zzehBx3looP/20uQAjRadPJFdV/B2mpZYqXMI4dIN9g7KJ1
 6uEoaGurzYWQQreDXswQ5vFUcQfIudEJ9Im9IF+9BUsFQ2uvPTJ4I+HDN++WH70B
 cIsmwwBr7Q4JUVP+O7T2WGtBY69jvHTpJrCCVtyHtwEyL4a1uyfelsAJXbxqaqis
 w1lmXNkkSqx5c67H3maNNDRnbutyLL2gO0TYdiBapOcc5V03OYKNnMbDqRTddqyt
 4UH4eYkFkNai8UJ476BXHU9ldlWzEkRBib/OKwF9k3oPj9W3kdQ/vd2IKK5a1fTX
 jIbOPSRRC8K/9Bxn1KEtdoU0Yy+rlm3xd7DtQl5RyGTD+tHVq3dN55WjoXBY83Yh
 r37y7uII9i09tPg5+APSX/jgodsIt4c46dKwvYuWXvB7ziomfsKxQiRanApJG6UX
 qS5NCUrlfYWlL302JOTvEtDBePXXiXQ065GuRjM948WMnVzXwEKwYUakGhvXQWMS
 jXCcOGW7GhnbY3+Ipn9chyhydHpKSxIb8oBk4cMRJU9jlN2GmjHgW8RMvT2WM6VF
 1F8acyMvf6en5tV6f23cjbW+iIMTS5egKNfqi8tdjGVxbowypyJYzjYOhaqk6veJ
 jHOmpglTXas0QD3ZRU7vGVlrvHqik8XyRsq3N9CQjVenRCbsQLKZRi1gTbIuspcR
 rejqH3Fs
 =kPg8
 -----END PGP SIGNATURE-----

Merge tag 'arm-drivers-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM driver updates from Olof Johansson:

 - Reset controllers: Adding support for Microchip Sparx5 Switch.

 - Memory controllers: ARM Primecell PL35x SMC memory controller driver
   cleanups and improvements.

 - i.MX SoC drivers: Power domain support for i.MX8MM and i.MX8MN.

 - Rockchip: RK3568 power domains support + DT binding updates,
   cleanups.

 - Qualcomm SoC drivers: Amend socinfo with more SoC/PMIC details,
   including support for MSM8226, MDM9607, SM6125 and SC8180X.

 - ARM FFA driver: "Firmware Framework for ARMv8-A", defining management
   interfaces and communication (including bus model) between partitions
   both in Normal and Secure Worlds.

 - Tegra Memory controller changes, including major rework to deal with
   identity mappings at boot and integration with ARM SMMU pieces.

* tag 'arm-drivers-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (120 commits)
  firmware: turris-mox-rwtm: add marvell,armada-3700-rwtm-firmware compatible string
  firmware: turris-mox-rwtm: show message about HWRNG registration
  firmware: turris-mox-rwtm: fail probing when firmware does not support hwrng
  firmware: turris-mox-rwtm: report failures better
  firmware: turris-mox-rwtm: fix reply status decoding function
  soc: imx: gpcv2: add support for i.MX8MN power domains
  dt-bindings: add defines for i.MX8MN power domains
  firmware: tegra: bpmp: Fix Tegra234-only builds
  iommu/arm-smmu: Use Tegra implementation on Tegra186
  iommu/arm-smmu: tegra: Implement SID override programming
  iommu/arm-smmu: tegra: Detect number of instances at runtime
  dt-bindings: arm-smmu: Add Tegra186 compatible string
  firmware: qcom_scm: Add MDM9607 compatible
  soc: qcom: rpmpd: Add MDM9607 RPM Power Domains
  soc: renesas: Add support to read LSI DEVID register of RZ/G2{L,LC} SoC's
  soc: renesas: Add ARCH_R9A07G044 for the new RZ/G2L SoC's
  dt-bindings: soc: rockchip: drop unnecessary #phy-cells from grf.yaml
  memory: emif: remove unused frequency and voltage notifiers
  memory: fsl_ifc: fix leak of private memory on probe failure
  memory: fsl_ifc: fix leak of IO mapping on probe failure
  ...
2021-07-10 09:46:20 -07:00
Linus Torvalds 6e207b8821 ARM: SoC changes for 5.14
A few SoC (code) changes have queued up this cycle, mostly for minor
 changes and some refactoring and cleanup of legacy platforms. This
 branch also contains a few of the fixes that weren't sent in by the end
 of the release (all fairly minor).
 
  - Adding an additional maintainer for the TEE subsystem (Sumit Garg)
 
  - Quite a significant modernization of the IXP4xx platforms by Linus
    Walleij, revisiting with a new PCI host driver/binding, removing legacy
    mach/* include dependencies and moving platform detection/config to
    drivers/soc. Also some updates/cleanup of platform data.
 
  - Core power domain support for Tegra platforms, and some improvements
    in build test coverage by adding stubs for compile test targets.
 
  - A handful of updates to i.MX platforms, adding legacy (non-PSCI) SMP
    support on i.MX7D, SoC ID setup for i.MX50, removal of platform data
    and board fixups for iMX6/7.
 
  ... and a few smaller changes and fixes for Samsung, OMAP, Allwinner,
  Rockchip.
 -----BEGIN PGP SIGNATURE-----
 
 iQJDBAABCgAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAmDojiQPHG9sb2ZAbGl4
 b20ubmV0AAoJEIwa5zzehBx3Z+kQAJofM2XXE3eHoIGINp+XuYZHCAdTxpIJfhsQ
 KPt4dzaxq0eBhrD8PICelJ2ymWz4c3sO2z+v79zQfOJdutnFKWTCRstqW8qdq9cE
 vzYh5pDJy0VmLkYSX/PzvfTLUQDM+Cx0sH/8e2gRwCC/F5tXolLA8lcqWQg9LnlC
 5joLOm2WL2uHDgPFZLR6Y1m0KabvUMMpYx6ji9EUx4qtc0VgRMRTSZkRZK4E1PU+
 ls175pPZxQfmTyFuHGc1L6KrfnHry8+YX/61sMlBfi96itMnBi05PcxljH8hMkQ8
 IVfqPYVnI2vX37f8MhcX4Wec8pKQ9SZqT9mbADGEG23XfZppT5cp7pJUACoZ/wJ5
 MMXn99hsEI0NO/gswKr2ZCCskydWrwOqhzubxZrYQtyFt38Sgs+mMLYxyQJKztbZ
 Laz+JBYKsvIlRctt+fArLp79EJx+CpSUpcha5Q0dQUmz3GWApPpS/6nMiNkq1Myv
 aByG9HXjOpRI5IiaOi7Fv/m/i+TsO43boNFerUIqPYi2AxmM9D8M2sJcyWHVwQRK
 glSAjISbp0GHAzVPM5JzhGIrCu4xC5Hf09Q+0OP6c3YVylwKNMurJCjCCql+ft8I
 Z41WVglS4xO5Y/qiWi+5pzg7/+VESBcsFn6PA5AJAAsDGgU5WHHXhI5kO7eUFAK9
 nuIbtqUS
 =b6Jo
 -----END PGP SIGNATURE-----

Merge tag 'arm-soc-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC updates from Olof Johansson:
 "A few SoC (code) changes have queued up this cycle, mostly for minor
  changes and some refactoring and cleanup of legacy platforms. This
  branch also contains a few of the fixes that weren't sent in by the
  end of the release (all fairly minor).

   - Adding an additional maintainer for the TEE subsystem (Sumit Garg)

   - Quite a significant modernization of the IXP4xx platforms by Linus
     Walleij, revisiting with a new PCI host driver/binding, removing
     legacy mach/* include dependencies and moving platform
     detection/config to drivers/soc. Also some updates/cleanup of
     platform data.

   - Core power domain support for Tegra platforms, and some
     improvements in build test coverage by adding stubs for compile
     test targets.

   - A handful of updates to i.MX platforms, adding legacy (non-PSCI)
     SMP support on i.MX7D, SoC ID setup for i.MX50, removal of platform
     data and board fixups for iMX6/7.

  ... and a few smaller changes and fixes for Samsung, OMAP, Allwinner,
  Rockchip"

* tag 'arm-soc-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (53 commits)
  MAINTAINERS: Add myself as TEE subsystem reviewer
  ixp4xx: fix spelling mistake in Kconfig "Devce" -> "Device"
  hw_random: ixp4xx: Add OF support
  hw_random: ixp4xx: Add DT bindings
  hw_random: ixp4xx: Turn into a module
  hw_random: ixp4xx: Use SPDX license tag
  hw_random: ixp4xx: enable compile-testing
  pata: ixp4xx: split platform data to its own header
  soc: ixp4xx: move cpu detection to linux/soc/ixp4xx/cpu.h
  PCI: ixp4xx: Add a new driver for IXP4xx
  PCI: ixp4xx: Add device tree bindings for IXP4xx
  ARM/ixp4xx: Make NEED_MACH_IO_H optional
  ARM/ixp4xx: Move the virtual IObases
  MAINTAINERS: ARM/MStar/Sigmastar SoCs: Add a link to the MStar tree
  ARM: debug: add UART early console support for MSTAR SoCs
  ARM: dts: ux500: Fix LED probing
  ARM: imx: add smp support for imx7d
  ARM: imx6q: drop of_platform_default_populate() from init_machine
  arm64: dts: rockchip: Update RK3399 PCI host bridge window to 32-bit address memory
  soc/tegra: fuse: Fix Tegra234-only builds
  ...
2021-07-10 09:22:44 -07:00
Conor Dooley 83d7b15608 mbox: add polarfire soc system controller mailbox
This driver adds support for the single mailbox channel of the MSS
system controller on the Microchip PolarFire SoC.

Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
2021-06-26 12:06:48 -05:00
Thierry Reding 47661ee182 memory: tegra: Add compile-test stub for tegra_mc_probe_device()
The tegra_mc_probe_device() symbol is only available when the TEGRA_MC
Kconfig option is enabled. Provide a stub if that's not the case so that
the driver can be compile-tested.

Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210618111846.1286166-1-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
2021-06-20 21:22:30 +02:00
Olof Johansson 777cf27fb2 soc/tegra: Changes for v5.14-rc1
These changes implement the core power domain for the PMC, and fix a
 couple of minor issues as well as add stubs to help some drivers be
 compile tested more easily.
 -----BEGIN PGP SIGNATURE-----
 
 iQJHBAABCAAxFiEEiOrDCAFJzPfAjcif3SOs138+s6EFAmDDjV4THHRyZWRpbmdA
 bnZpZGlhLmNvbQAKCRDdI6zXfz6zoXVsD/0QgZHiuEH8rU42JtYGB/rjCskWUPen
 BOtcrIi+QxJ7m8q4qnRrPIeE8ETjQAB92pWpZE8VQ260Pk/s8NAeIXBbP7I2lKU8
 M+TkwvCQ8zZw18q9ZPinqSUHgVsh7Q+7kQggHGZcYpE4rOmlb0oTr9B2EprdSpBl
 hVNGtcaJ9Ovqri1ioDi/owUaxYpeJ3L8A++luIv9K8oDUpN7GBw3nV0dMOBvUOBs
 nT9iQFEThvo0NRNs4zPNDPLPsLJFwePRDmY9SE4PCreDKo26+VWAamooW8R6iEnU
 P7OOfCSZbLqMs8Sfkjrb742sqWX50okFFJQG6aW3BOln3IA5esc9uJ3l2jH6GZP1
 21hestxJjK2JuZLv8uMtGHura8do7e4PrYVvxOT6Lp85AXaXA1/uieAWRyh40lcD
 d4S4hL3prlfgepj6eUy40MnbLbatsRyQoFYdloZtB+cZb+KxMSV/Lx+j0Y5VyOI/
 OpVcTxTxwAZRrVcHTISkUjkxLProY1hQwQP9vexRMIn8SB+ZhgztjHJQuUxa25at
 c2Q1aOeGr+h3w1NYpOa+u1tyyKt/Vw92tA84MHaoGoWJg2DGXDAh66HFpiFrmE8q
 +n2wc/uyhz1bdS38ky73ibJ6iQ96ucRLxEjCIz+59hdZ57bEYnF+EUJtNdMSyqXg
 hGVs5fnWFlw97Q==
 =g0AU
 -----END PGP SIGNATURE-----

Merge tag 'tegra-for-5.14-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/soc

soc/tegra: Changes for v5.14-rc1

These changes implement the core power domain for the PMC, and fix a
couple of minor issues as well as add stubs to help some drivers be
compile tested more easily.

* tag 'tegra-for-5.14-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  soc/tegra: fuse: Fix Tegra234-only builds
  soc/tegra: fuse: Don't return -ENOMEM when allocate lookups failed
  soc/tegra: regulators: Support core domain state syncing
  soc/tegra: pmc: Add driver state syncing
  soc/tegra: pmc: Add core power domain
  soc/tegra: fuse: Add stubs needed for compile-testing
  soc/tegra: Add devm_tegra_core_dev_init_opp_table()
  soc/tegra: Add stub for soc_is_tegra()
  soc/tegra: regulators: Bump voltages on system reboot
  regulator: core: Add regulator_sync_voltage_rdev()

Link: https://lore.kernel.org/r/20210611164437.3568059-2-thierry.reding@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
2021-06-15 08:35:29 -07:00
Thierry Reding 393d66fd2c memory: tegra: Implement SID override programming
Instead of programming all SID overrides during early boot, perform the
operation on-demand after the SMMU translations have been set up for a
device. This reuses data from device tree to match memory clients for a
device and programs the SID specified in device tree, which corresponds
to the SID used for the SMMU context banks for the device.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210603164632.1000458-2-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
2021-06-03 21:50:43 +02:00
Thierry Reding 7355c7b9ae memory: tegra: Unify drivers
The Tegra210 (and earlier) driver now supports all the functionality
that the Tegra186 (and later) driver does, so they can be unified.

Note that previously the Tegra186 (and later) driver could be unloaded,
even if that was perhaps not very useful. Older chips don't support that
yet, but once they do this code can be reenabled.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-11-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
2021-06-03 21:49:41 +02:00
Thierry Reding 1079a66bc3 memory: tegra: Parameterize interrupt handler
Tegra20 requires a slightly different interrupt handler than Tegra30 and
later, so parameterize the handler, so that each SoC implementation can
provide its own.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-8-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
2021-06-03 21:49:41 +02:00
Thierry Reding c64738e949 memory: tegra: Make per-SoC setup more generic
The current per-SoC setup code runs at a fairly arbitrary point during
probe, thereby making it less flexible for other SoC generations. Move
the call around slightly (after only the very basic, common setup that
applies to all SoC generations has been performed), which will allow
it to be used for other implementations.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-6-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
2021-06-03 21:49:41 +02:00
Thierry Reding 5c9016f0a8 memory: tegra: Push suspend/resume into SoC drivers
Continuing the scheme of unification, push suspend/resume callbacks into
per-SoC driver so that they can be properly parameterized.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-5-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
2021-06-03 21:49:41 +02:00
Thierry Reding 6cc884c1c7 memory: tegra: Introduce struct tegra_mc_ops
Subsequent patches will introduce further callbacks, so create a new
struct tegra_mc_ops to collect all of them in a single place. Move the
existing ->init() callback into the new structure.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-4-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
2021-06-03 21:49:40 +02:00
Thierry Reding e899993845 memory: tegra: Unify struct tegra_mc across SoC generations
As another step towards unifying both the Tegra210 (and earlier) and
Tegra186 (and later) memory controller drivers, unify the structures
that are used to represent them.

Note that this comes at a slight space penalty since some fields are
not used on all generations, but the benefits of unifying the driver
outweigh the downsides.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-3-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
2021-06-03 21:49:40 +02:00
Thierry Reding 4f1ac76e5e memory: tegra: Consolidate register fields
Subsequent patches will add more register fields to the tegra_mc_client
structure, so consolidate all register field definitions into a common
sub-structure for coherency.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20210602163302.120041-2-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
2021-06-03 21:49:40 +02:00
Dmitry Osipenko 41bafa698d soc/tegra: pmc: Add driver state syncing
Add driver state syncing that is invoked once all PMC consumers are
attached and ready. The consumers are the power domain clients.
The synchronization callback is invoked once all client drivers are
probed, the driver core handles this for us. This callback informs
PMC driver that all voltage votes are initialized by each PD client
and it's safe to begin voltage scaling of the core power domain.

Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
[treding@nvidia.com: squash DT backwards-compatibility patch]
Signed-off-by: Thierry Reding <treding@nvidia.com>
2021-06-02 10:58:55 +02:00
Dmitry Osipenko 30b44e8177 soc/tegra: fuse: Add stubs needed for compile-testing
Add missing stubs that will allow Tegra memory driver to be compile-tested
by kernel build bots.

Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
2021-06-01 12:15:13 +02:00
Dmitry Osipenko b8818de9c0 soc/tegra: Add devm_tegra_core_dev_init_opp_table()
Add common helper which initializes OPP table for Tegra SoC core devices.

Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Paul Fertser <fercerpav@gmail.com> # PAZ00 T20
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20 and TK1 T124
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
2021-06-01 12:14:59 +02:00
Dmitry Osipenko 4333e03000 soc/tegra: Add stub for soc_is_tegra()
Add stub required for compile-testing of drivers.

Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
2021-06-01 12:14:44 +02:00
Jonathan Neuschäfer 22b5059b95 ARM: imx: Initialize SoC ID on i.MX50
As on i.MX51 and i.MX53, initialize the SoC ID based on the SoC
compatible string of the board.

Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2021-05-13 15:42:21 +08:00
Linus Torvalds 9d31d23389 Networking changes for 5.13.
Core:
 
  - bpf:
 	- allow bpf programs calling kernel functions (initially to
 	  reuse TCP congestion control implementations)
 	- enable task local storage for tracing programs - remove the
 	  need to store per-task state in hash maps, and allow tracing
 	  programs access to task local storage previously added for
 	  BPF_LSM
 	- add bpf_for_each_map_elem() helper, allowing programs to
 	  walk all map elements in a more robust and easier to verify
 	  fashion
 	- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
 	  redirection
 	- lpm: add support for batched ops in LPM trie
 	- add BTF_KIND_FLOAT support - mostly to allow use of BTF
 	  on s390 which has floats in its headers files
 	- improve BPF syscall documentation and extend the use of kdoc
 	  parsing scripts we already employ for bpf-helpers
 	- libbpf, bpftool: support static linking of BPF ELF files
 	- improve support for encapsulation of L2 packets
 
  - xdp: restructure redirect actions to avoid a runtime lookup,
 	improving performance by 4-8% in microbenchmarks
 
  - xsk: build skb by page (aka generic zerocopy xmit) - improve
 	performance of software AF_XDP path by 33% for devices
 	which don't need headers in the linear skb part (e.g. virtio)
 
  - nexthop: resilient next-hop groups - improve path stability
 	on next-hops group changes (incl. offload for mlxsw)
 
  - ipv6: segment routing: add support for IPv4 decapsulation
 
  - icmp: add support for RFC 8335 extended PROBE messages
 
  - inet: use bigger hash table for IP ID generation
 
  - tcp: deal better with delayed TX completions - make sure we don't
 	give up on fast TCP retransmissions only because driver is
 	slow in reporting that it completed transmitting the original
 
  - tcp: reorder tcp_congestion_ops for better cache locality
 
  - mptcp:
 	- add sockopt support for common TCP options
 	- add support for common TCP msg flags
 	- include multiple address ids in RM_ADDR
 	- add reset option support for resetting one subflow
 
  - udp: GRO L4 improvements - improve 'forward' / 'frag_list'
 	co-existence with UDP tunnel GRO, allowing the first to take
 	place correctly	even for encapsulated UDP traffic
 
  - micro-optimize dev_gro_receive() and flow dissection, avoid
 	retpoline overhead on VLAN and TEB GRO
 
  - use less memory for sysctls, add a new sysctl type, to allow using
 	u8 instead of "int" and "long" and shrink networking sysctls
 
  - veth: allow GRO without XDP - this allows aggregating UDP
 	packets before handing them off to routing, bridge, OvS, etc.
 
  - allow specifing ifindex when device is moved to another namespace
 
  - netfilter:
 	- nft_socket: add support for cgroupsv2
 	- nftables: add catch-all set element - special element used
 	  to define a default action in case normal lookup missed
 	- use net_generic infra in many modules to avoid allocating
 	  per-ns memory unnecessarily
 
  - xps: improve the xps handling to avoid potential out-of-bound
 	accesses and use-after-free when XPS change race with other
 	re-configuration under traffic
 
  - add a config knob to turn off per-cpu netdev refcnt to catch
 	underflows in testing
 
 Device APIs:
 
  - add WWAN subsystem to organize the WWAN interfaces better and
    hopefully start driving towards more unified and vendor-
    -independent APIs
 
  - ethtool:
 	- add interface for reading IEEE MIB stats (incl. mlx5 and
 	  bnxt support)
 	- allow network drivers to dump arbitrary SFP EEPROM data,
 	  current offset+length API was a poor fit for modern SFP
 	  which define EEPROM in terms of pages (incl. mlx5 support)
 
  - act_police, flow_offload: add support for packet-per-second
 	policing (incl. offload for nfp)
 
  - psample: add additional metadata attributes like transit delay
 	for packets sampled from switch HW (and corresponding egress
 	and policy-based sampling in the mlxsw driver)
 
  - dsa: improve support for sandwiched LAGs with bridge and DSA
 
  - netfilter:
 	- flowtable: use direct xmit in topologies with IP
 	  forwarding, bridging, vlans etc.
 	- nftables: counter hardware offload support
 
  - Bluetooth:
 	- improvements for firmware download w/ Intel devices
 	- add support for reading AOSP vendor capabilities
 	- add support for virtio transport driver
 
  - mac80211:
 	- allow concurrent monitor iface and ethernet rx decap
 	- set priority and queue mapping for injected frames
 
  - phy: add support for Clause-45 PHY Loopback
 
  - pci/iov: add sysfs MSI-X vector assignment interface
 	to distribute MSI-X resources to VFs (incl. mlx5 support)
 
 New hardware/drivers:
 
  - dsa: mv88e6xxx: add support for Marvell mv88e6393x -
 	11-port Ethernet switch with 8x 1-Gigabit Ethernet
 	and 3x 10-Gigabit interfaces.
 
  - dsa: support for legacy Broadcom tags used on BCM5325, BCM5365
 	and BCM63xx switches
 
  - Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
 
  - ath11k: support for QCN9074 a 802.11ax device
 
  - Bluetooth: Broadcom BCM4330 and BMC4334
 
  - phy: Marvell 88X2222 transceiver support
 
  - mdio: add BCM6368 MDIO mux bus controller
 
  - r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
 
  - mana: driver for Microsoft Azure Network Adapter (MANA)
 
  - Actions Semi Owl Ethernet MAC
 
  - can: driver for ETAS ES58X CAN/USB interfaces
 
 Pure driver changes:
 
  - add XDP support to: enetc, igc, stmmac
  - add AF_XDP support to: stmmac
 
  - virtio:
 	- page_to_skb() use build_skb when there's sufficient tailroom
 	  (21% improvement for 1000B UDP frames)
 	- support XDP even without dedicated Tx queues - share the Tx
 	  queues with the stack when necessary
 
  - mlx5:
 	- flow rules: add support for mirroring with conntrack,
 	  matching on ICMP, GTP, flex filters and more
 	- support packet sampling with flow offloads
 	- persist uplink representor netdev across eswitch mode
 	  changes
 	- allow coexistence of CQE compression and HW time-stamping
 	- add ethtool extended link error state reporting
 
  - ice, iavf: support flow filters, UDP Segmentation Offload
 
  - dpaa2-switch:
 	- move the driver out of staging
 	- add spanning tree (STP) support
 	- add rx copybreak support
 	- add tc flower hardware offload on ingress traffic
 
  - ionic:
 	- implement Rx page reuse
 	- support HW PTP time-stamping
 
  - octeon: support TC hardware offloads - flower matching on ingress
 	and egress ratelimitting.
 
  - stmmac:
 	- add RX frame steering based on VLAN priority in tc flower
 	- support frame preemption (FPE)
 	- intel: add cross time-stamping freq difference adjustment
 
  - ocelot:
 	- support forwarding of MRP frames in HW
 	- support multiple bridges
 	- support PTP Sync one-step timestamping
 
  - dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
 	learning, flooding etc.
 
  - ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
 	SC7280 SoCs)
 
  - mt7601u: enable TDLS support
 
  - mt76:
 	- add support for 802.3 rx frames (mt7915/mt7615)
 	- mt7915 flash pre-calibration support
 	- mt7921/mt7663 runtime power management fixes
 
 Signed-off-by: Jakub Kicinski <kuba@kernel.org>
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCAAdFiEE6jPA+I1ugmIBA4hXMUZtbf5SIrsFAmCKFPIACgkQMUZtbf5S
 Irtw0g/+NA8bWdHNgG4H5rya0pv2z3IieLRmSdDfKRQQXcJpklawc5MKVVaTee/Q
 5/QqgPdCsu1LAU6JXBKsKmyDDaMlQKdWuKbOqDSiAQKoMesZStTEHf9d851ZzgxA
 Cdb6O7BD3lBl/IN+oxNG+KcmD1LKquTPKGySq2mQtEdLO12ekAsranzmj4voKffd
 q9tBShpXQ7Dq77DLYfiQXVCvsizNcbbJFuxX0o9Lpb9+61ZyYAbogZSa9ypiZZwR
 I/9azRBtJg7UV1aD/cLuAfy66Qh7t63+rCxVazs5Os8jVO26P/jQdisnnOe/x+p9
 wYEmKm3GSu0V4SAPxkWW+ooKusflCeqDoMIuooKt6kbP6BRj540veGw3Ww/m5YFr
 7pLQkTSP/tSjuGQIdBE1LOP5LBO8DZeC8Kiop9V0fzAW9hFSZbEq25WW0bPj8QQO
 zA4Z7yWlslvxcfY2BdJX3wD8klaINkl/8fDWZFFsBdfFX2VeLtm7Xfduw34BJpvU
 rYT3oWr6PhtkPAKR32SUcemSfeWgIVU41eSshzRz3kez1NngBUuLlSGGSEaKbes5
 pZVt6pYFFVByyf6MTHFEoQvafZfEw04JILZpo4R5V8iTHzom0kD3Py064sBiXEw2
 B6t+OW4qgcxGblpFkK2lD4kR2s1TPUs0ckVO6sAy1x8q60KKKjY=
 =vcbA
 -----END PGP SIGNATURE-----

Merge tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

Pull networking updates from Jakub Kicinski:
 "Core:

   - bpf:
        - allow bpf programs calling kernel functions (initially to
          reuse TCP congestion control implementations)
        - enable task local storage for tracing programs - remove the
          need to store per-task state in hash maps, and allow tracing
          programs access to task local storage previously added for
          BPF_LSM
        - add bpf_for_each_map_elem() helper, allowing programs to walk
          all map elements in a more robust and easier to verify fashion
        - sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
          redirection
        - lpm: add support for batched ops in LPM trie
        - add BTF_KIND_FLOAT support - mostly to allow use of BTF on
          s390 which has floats in its headers files
        - improve BPF syscall documentation and extend the use of kdoc
          parsing scripts we already employ for bpf-helpers
        - libbpf, bpftool: support static linking of BPF ELF files
        - improve support for encapsulation of L2 packets

   - xdp: restructure redirect actions to avoid a runtime lookup,
     improving performance by 4-8% in microbenchmarks

   - xsk: build skb by page (aka generic zerocopy xmit) - improve
     performance of software AF_XDP path by 33% for devices which don't
     need headers in the linear skb part (e.g. virtio)

   - nexthop: resilient next-hop groups - improve path stability on
     next-hops group changes (incl. offload for mlxsw)

   - ipv6: segment routing: add support for IPv4 decapsulation

   - icmp: add support for RFC 8335 extended PROBE messages

   - inet: use bigger hash table for IP ID generation

   - tcp: deal better with delayed TX completions - make sure we don't
     give up on fast TCP retransmissions only because driver is slow in
     reporting that it completed transmitting the original

   - tcp: reorder tcp_congestion_ops for better cache locality

   - mptcp:
        - add sockopt support for common TCP options
        - add support for common TCP msg flags
        - include multiple address ids in RM_ADDR
        - add reset option support for resetting one subflow

   - udp: GRO L4 improvements - improve 'forward' / 'frag_list'
     co-existence with UDP tunnel GRO, allowing the first to take place
     correctly even for encapsulated UDP traffic

   - micro-optimize dev_gro_receive() and flow dissection, avoid
     retpoline overhead on VLAN and TEB GRO

   - use less memory for sysctls, add a new sysctl type, to allow using
     u8 instead of "int" and "long" and shrink networking sysctls

   - veth: allow GRO without XDP - this allows aggregating UDP packets
     before handing them off to routing, bridge, OvS, etc.

   - allow specifing ifindex when device is moved to another namespace

   - netfilter:
        - nft_socket: add support for cgroupsv2
        - nftables: add catch-all set element - special element used to
          define a default action in case normal lookup missed
        - use net_generic infra in many modules to avoid allocating
          per-ns memory unnecessarily

   - xps: improve the xps handling to avoid potential out-of-bound
     accesses and use-after-free when XPS change race with other
     re-configuration under traffic

   - add a config knob to turn off per-cpu netdev refcnt to catch
     underflows in testing

  Device APIs:

   - add WWAN subsystem to organize the WWAN interfaces better and
     hopefully start driving towards more unified and vendor-
     independent APIs

   - ethtool:
        - add interface for reading IEEE MIB stats (incl. mlx5 and bnxt
          support)
        - allow network drivers to dump arbitrary SFP EEPROM data,
          current offset+length API was a poor fit for modern SFP which
          define EEPROM in terms of pages (incl. mlx5 support)

   - act_police, flow_offload: add support for packet-per-second
     policing (incl. offload for nfp)

   - psample: add additional metadata attributes like transit delay for
     packets sampled from switch HW (and corresponding egress and
     policy-based sampling in the mlxsw driver)

   - dsa: improve support for sandwiched LAGs with bridge and DSA

   - netfilter:
        - flowtable: use direct xmit in topologies with IP forwarding,
          bridging, vlans etc.
        - nftables: counter hardware offload support

   - Bluetooth:
        - improvements for firmware download w/ Intel devices
        - add support for reading AOSP vendor capabilities
        - add support for virtio transport driver

   - mac80211:
        - allow concurrent monitor iface and ethernet rx decap
        - set priority and queue mapping for injected frames

   - phy: add support for Clause-45 PHY Loopback

   - pci/iov: add sysfs MSI-X vector assignment interface to distribute
     MSI-X resources to VFs (incl. mlx5 support)

  New hardware/drivers:

   - dsa: mv88e6xxx: add support for Marvell mv88e6393x - 11-port
     Ethernet switch with 8x 1-Gigabit Ethernet and 3x 10-Gigabit
     interfaces.

   - dsa: support for legacy Broadcom tags used on BCM5325, BCM5365 and
     BCM63xx switches

   - Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches

   - ath11k: support for QCN9074 a 802.11ax device

   - Bluetooth: Broadcom BCM4330 and BMC4334

   - phy: Marvell 88X2222 transceiver support

   - mdio: add BCM6368 MDIO mux bus controller

   - r8152: support RTL8153 and RTL8156 (USB Ethernet) chips

   - mana: driver for Microsoft Azure Network Adapter (MANA)

   - Actions Semi Owl Ethernet MAC

   - can: driver for ETAS ES58X CAN/USB interfaces

  Pure driver changes:

   - add XDP support to: enetc, igc, stmmac

   - add AF_XDP support to: stmmac

   - virtio:
        - page_to_skb() use build_skb when there's sufficient tailroom
          (21% improvement for 1000B UDP frames)
        - support XDP even without dedicated Tx queues - share the Tx
          queues with the stack when necessary

   - mlx5:
        - flow rules: add support for mirroring with conntrack, matching
          on ICMP, GTP, flex filters and more
        - support packet sampling with flow offloads
        - persist uplink representor netdev across eswitch mode changes
        - allow coexistence of CQE compression and HW time-stamping
        - add ethtool extended link error state reporting

   - ice, iavf: support flow filters, UDP Segmentation Offload

   - dpaa2-switch:
        - move the driver out of staging
        - add spanning tree (STP) support
        - add rx copybreak support
        - add tc flower hardware offload on ingress traffic

   - ionic:
        - implement Rx page reuse
        - support HW PTP time-stamping

   - octeon: support TC hardware offloads - flower matching on ingress
     and egress ratelimitting.

   - stmmac:
        - add RX frame steering based on VLAN priority in tc flower
        - support frame preemption (FPE)
        - intel: add cross time-stamping freq difference adjustment

   - ocelot:
        - support forwarding of MRP frames in HW
        - support multiple bridges
        - support PTP Sync one-step timestamping

   - dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
     learning, flooding etc.

   - ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
     SC7280 SoCs)

   - mt7601u: enable TDLS support

   - mt76:
        - add support for 802.3 rx frames (mt7915/mt7615)
        - mt7915 flash pre-calibration support
        - mt7921/mt7663 runtime power management fixes"

* tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2451 commits)
  net: selftest: fix build issue if INET is disabled
  net: netrom: nr_in: Remove redundant assignment to ns
  net: tun: Remove redundant assignment to ret
  net: phy: marvell: add downshift support for M88E1240
  net: dsa: ksz: Make reg_mib_cnt a u8 as it never exceeds 255
  net/sched: act_ct: Remove redundant ct get and check
  icmp: standardize naming of RFC 8335 PROBE constants
  bpf, selftests: Update array map tests for per-cpu batched ops
  bpf: Add batched ops support for percpu array
  bpf: Implement formatted output helpers with bstr_printf
  seq_file: Add a seq_bprintf function
  sfc: adjust efx->xdp_tx_queue_count with the real number of initialized queues
  net:nfc:digital: Fix a double free in digital_tg_recv_dep_req
  net: fix a concurrency bug in l2tp_tunnel_register()
  net/smc: Remove redundant assignment to rc
  mpls: Remove redundant assignment to err
  llc2: Remove redundant assignment to rc
  net/tls: Remove redundant initialization of record
  rds: Remove redundant assignment to nr_sig
  dt-bindings: net: mdio-gpio: add compatible for microchip,mdio-smi0
  ...
2021-04-29 11:57:23 -07:00
Yangbo Lu 39e5308b32 net: mscc: ocelot: support PTP Sync one-step timestamping
Although HWTSTAMP_TX_ONESTEP_SYNC existed in ioctl for hardware timestamp
configuration, the PTP Sync one-step timestamping had never been supported.

This patch is to truely support it.

- ocelot_port_txtstamp_request()
  This function handles tx timestamp request by storing
  ptp_cmd(tx timestamp type) in OCELOT_SKB_CB(skb)->ptp_cmd,
  and additionally for two-step timestamp storing ts_id in
  OCELOT_SKB_CB(clone)->ptp_cmd.

- ocelot_ptp_rew_op()
  During xmit, this function is called to get rew_op (rewriter option) by
  checking skb->cb for tx timestamp request, and configure to transmitting.

Non-onestep-Sync packet with one-step timestamp request falls back to use
two-step timestamp.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-27 14:10:15 -07:00
Yangbo Lu 682eaad93e net: mscc: ocelot: convert to ocelot_port_txtstamp_request()
Convert to a common ocelot_port_txtstamp_request() for TX timestamp
request handling.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-27 14:10:15 -07:00
Yangbo Lu c4b364ce12 net: dsa: free skb->cb usage in core driver
Free skb->cb usage in core driver and let device drivers decide to
use or not. The reason having a DSA_SKB_CB(skb)->clone was because
dsa_skb_tx_timestamp() which may set the clone pointer was called
before p->xmit() which would use the clone if any, and the device
driver has no way to initialize the clone pointer.

This patch just put memset(skb->cb, 0, sizeof(skb->cb)) at beginning
of dsa_slave_xmit(). Some new features in the future, like one-step
timestamp may need more bytes of skb->cb to use in
dsa_skb_tx_timestamp(), and p->xmit().

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-27 14:10:15 -07:00
Linus Torvalds 37f00ab4a0 ARM: SoC drivers for v5.13
Updates for SoC specific drivers include a few subsystems that
 have their own maintainers but send them through the soc tree:
 
 TEE/OP-TEE:
  -  Add tracepoints around calls to secure world
 
 Memory controller drivers:
  - Minor fixes for Renesas, Exynos, Mediatek and Tegra platforms
  - Add debug statistics to Tegra20 memory controller
  - Update Tegra bindings and convert to dtschema
 
 ARM SCMI Firmware:
  - Support for modular SCMI protocols and vendor specific extensions
  - New SCMI IIO driver
  - Per-cpu DVFS
 
 The other driver changes are all from the platform maintainers
 directly and reflect the drivers that don't fit into any other
 subsystem as well as treewide changes for a particular platform.
 
 SoCFPGA:
  - Various cleanups contributed by Krzysztof Kozlowski
 
 Mediatek:
  - add MT8183 support to mutex driver
  - MMSYS: use per SoC array to describe the possible routing
  - add MMSYS support for MT8183 and MT8167
  - add support for PMIC wrapper with integrated arbiter
  - add support for MT8192/MT6873
 
 Tegra:
  - Bug fixes to PMC and clock drivers
 
 NXP/i.MX:
  - Update SCU power domain driver to keep console domain power on.
  - Add missing ADC1 power domain to SCU power domain driver.
  - Update comments for single global power domain in SCU power domain
    driver.
  - Add i.MX51/i.MX53 unique id support to i.MX SoC driver.
 
 NXP/FSL SoC driver updates for v5.13
  - Add ACPI support for RCPM driver
  - Use generic io{read,write} for QE drivers after performance optimized
    for PowerPC
  - Fix QBMAN probe to cleanup HW states correctly for kexec
  - Various cleanup and style fix for QBMAN/QE/GUTS drivers
 
 OMAP:
  - Preparation to use devicetree for genpd
  - ti-sysc needs iorange check improved when the interconnect target module
    has no control registers listed
  - ti-sysc needs to probe l4_wkup and l4_cfg interconnects first to avoid
    issues with missing resources and unnecessary deferred probe
  - ti-sysc debug option can now detect more devices
  - ti-sysc now warns if an old incomplete devicetree data is found as we
    now rely on it being complete for am3 and 4
  - soc init code needs to check for prcm and prm nodes for omap4/5 and dra7
  - omap-prm driver needs to enable autoidle retention support for omap4
  - omap5 clocks are missing gpmc and ocmc clock registers
  - pci-dra7xx now needs to use builtin_platform_driver instead of using
    builtin_platform_driver_probe for deferred probe to work
 
 Raspberry Pi:
  - Fix-up all RPi firmware drivers so as for unbind to happen in an
    orderly fashion
  - Support for RPi's PoE hat PWM bus
 
 Qualcomm
  - Improved detection for SCM calling conventions
  - Support for OEM specific wifi firmware path
  - Added drivers for SC7280/SM8350: RPMH, LLCC< AOSS QMP
 
 Signed-off-by: Arnd Bergmann <arnd@arndb.de>
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmCC2JwACgkQmmx57+YA
 GNkgRg//cBtq2NyDbjiNABxFSkmGCfcc0w0C2wjVzr4cfg6BLTbuvvlpZxI912pu
 P1G2sbsdfQJ8sSeIyZos+PilWK0zHrqlaGZfKI19US45dMjpteDBgsPd7wNZwBjQ
 jbops3YLjztZK1HpY4dIdvMnfxt7yRqhBWaTbPuCwQ35c5KsOM8NHB3cP3BUINWK
 x1uuBCv9svppzwdDiPxneV93WKEzabOUo+WBMPyh5vnyvmW17Iif4BA/VKQxzymm
 mWUi8HHpKBpvntJOKwAD2hnLAdpR3SwX20SLOpyLhnJMotbzNUEqq3LdRxDNPdHk
 ry+rarJ78JGlYfpcfegf2bLf5ITNMfOyRGkjtzeYpcZIXPjufOg9DA9YtAy37k0u
 L0T/9gQ+tQ01WGMca77OyUtIqJKdblZrQMfuH/yGlR99bqFQMV7rNc7GNlX1MXp/
 zw4aOYrRWGtGEeAjx5JJWcYydvMSJpCrqxTz3YhgeJECHB2iA6YkV3NROR4TLW//
 tfxaKqxR/KmSqE6hoVOAuuQ0BLXNlql/+4EE6MKsAOBiKPJclvmJg4CyuY8G21ev
 9Su0zJnXMzai7gNu32v1pizGj26+AOhxCEgAG0mGgk2jlQSn24CKgm5e7kCUewcF
 j/1XksNPT95v/K8MsLpXe5xGvF3jhA1BlFfvjJNZOrcZywBXRxg=
 =iidq
 -----END PGP SIGNATURE-----

Merge tag 'arm-drivers-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC driver updates from Arnd Bergmann:
 "Updates for SoC specific drivers include a few subsystems that have
  their own maintainers but send them through the soc tree:

  TEE/OP-TEE:
   - Add tracepoints around calls to secure world

  Memory controller drivers:
   - Minor fixes for Renesas, Exynos, Mediatek and Tegra platforms
   - Add debug statistics to Tegra20 memory controller
   - Update Tegra bindings and convert to dtschema

  ARM SCMI Firmware:
   - Support for modular SCMI protocols and vendor specific extensions
   - New SCMI IIO driver
   - Per-cpu DVFS

  The other driver changes are all from the platform maintainers
  directly and reflect the drivers that don't fit into any other
  subsystem as well as treewide changes for a particular platform.

  SoCFPGA:
   - Various cleanups contributed by Krzysztof Kozlowski

  Mediatek:
   - add MT8183 support to mutex driver
   - MMSYS: use per SoC array to describe the possible routing
   - add MMSYS support for MT8183 and MT8167
   - add support for PMIC wrapper with integrated arbiter
   - add support for MT8192/MT6873

  Tegra:
   - Bug fixes to PMC and clock drivers

  NXP/i.MX:
   - Update SCU power domain driver to keep console domain power on.
   - Add missing ADC1 power domain to SCU power domain driver.
   - Update comments for single global power domain in SCU power domain
     driver.
   - Add i.MX51/i.MX53 unique id support to i.MX SoC driver.

  NXP/FSL SoC driver updates for v5.13
   - Add ACPI support for RCPM driver
   - Use generic io{read,write} for QE drivers after performance
     optimized for PowerPC
   - Fix QBMAN probe to cleanup HW states correctly for kexec
   - Various cleanup and style fix for QBMAN/QE/GUTS drivers

  OMAP:
   - Preparation to use devicetree for genpd
   - ti-sysc needs iorange check improved when the interconnect target
     module has no control registers listed
   - ti-sysc needs to probe l4_wkup and l4_cfg interconnects first to
     avoid issues with missing resources and unnecessary deferred probe
   - ti-sysc debug option can now detect more devices
   - ti-sysc now warns if an old incomplete devicetree data is found as
     we now rely on it being complete for am3 and 4
   - soc init code needs to check for prcm and prm nodes for omap4/5 and
     dra7
   - omap-prm driver needs to enable autoidle retention support for
     omap4
   - omap5 clocks are missing gpmc and ocmc clock registers
   - pci-dra7xx now needs to use builtin_platform_driver instead of
     using builtin_platform_driver_probe for deferred probe to work

  Raspberry Pi:
   - Fix-up all RPi firmware drivers so as for unbind to happen in an
     orderly fashion
   - Support for RPi's PoE hat PWM bus

  Qualcomm
   - Improved detection for SCM calling conventions
   - Support for OEM specific wifi firmware path
   - Added drivers for SC7280/SM8350: RPMH, LLCC< AOSS QMP"

* tag 'arm-drivers-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
  soc: aspeed: fix a ternary sign expansion bug
  memory: mtk-smi: Add device-link between smi-larb and smi-common
  memory: samsung: exynos5422-dmc: handle clk_set_parent() failure
  memory: renesas-rpc-if: fix possible NULL pointer dereference of resource
  clk: socfpga: fix iomem pointer cast on 64-bit
  soc: aspeed: Adapt to new LPC device tree layout
  pinctrl: aspeed-g5: Adapt to new LPC device tree layout
  ipmi: kcs: aspeed: Adapt to new LPC DTS layout
  ARM: dts: Remove LPC BMC and Host partitions
  dt-bindings: aspeed-lpc: Remove LPC partitioning
  soc: fsl: enable acpi support in RCPM driver
  soc: qcom: mdt_loader: Detect truncated read of segments
  soc: qcom: mdt_loader: Validate that p_filesz < p_memsz
  soc: qcom: pdr: Fix error return code in pdr_register_listener
  firmware: qcom_scm: Fix kernel-doc function names to match
  firmware: qcom_scm: Suppress sysfs bind attributes
  firmware: qcom_scm: Workaround lack of "is available" call on SC7180
  firmware: qcom_scm: Reduce locking section for __get_convention()
  firmware: qcom_scm: Make __qcom_scm_is_call_available() return bool
  Revert "soc: fsl: qe: introduce qe_io{read,write}* wrappers"
  ...
2021-04-26 12:11:52 -07:00
Arnd Bergmann 41c39cfc84 NXP/FSL SoC driver updates for v5.13
- Add ACPI support for RCPM driver
 - Use generic io{read,write} for QE drivers after performance optimized
   for PowerPC
 - Fix QBMAN probe to cleanup HW states correctly for kexec
 - Various cleanup and style fix for QBMAN/QE/GUTS drivers
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEhb3UXAyxp6UQ0v6khtxQDvusFVQFAmBvf7gACgkQhtxQDvus
 FVTBLxAAgo7FWiVCMD+wnMy3nceAV4U9OZljumEKfvt7g27oMN9i/AWaWwzJ+wsF
 zxMK9p0u8wCTG7PQIGbC4N1fRAaapc1w3TzDhFK4Uf5kqaoddqiFMf4IeRFmnYSF
 6GDbxgxdZkvyGpYJ31Uo750UmC1Q9zmNoh17Nrs2wN12FLFlmiABokklzOuwKBxI
 DLzdgbuTuBxGAv/6zSBmye391C0kf+ky6haOpyzHKToBnYJv/LyaGQGEGckfsnct
 uKnigu7MjU+1l0LhftAT52UoFRR6SeyguqYbq4JAFvNJd66eNpZZpyJnGX8y7hJN
 V8y4cvgeJBZl1ssVQVNA5sJSb9NCyPx0svwZqzJ3kdMWd8t8n2l4FrJSdPnjvCbz
 HRwSzoMmSrQJZp+2LJATSHsHZz5ArBp+o79fLjWf/1aYO92B6MkZvdiL45ATl9uF
 XOQJITdHI1rFWxXmu9rzUcgZx81LEf5jVP+L3GBrOIpPa6R0SQgXLInflVxoB+/l
 SaJRp5CKjBstOvswJlA0dNyMNSn07qNjiR67Gvh7UXGvIa8w0Njv41ZYms2zvErd
 6EIM1SuzrkByrq3zn+AiCNzTATgIJgU+JDq7doKwqCzBW9oBshZ9U3KKDdElqLv9
 2UjMpP5dIkdbjh9vHZ+BwutuSjDwkkJrk40deck+9Q3/ZkNPvug=
 =+DV0
 -----END PGP SIGNATURE-----

Merge tag 'soc-fsl-next-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/drivers

NXP/FSL SoC driver updates for v5.13

- Add ACPI support for RCPM driver
- Use generic io{read,write} for QE drivers after performance optimized
  for PowerPC
- Fix QBMAN probe to cleanup HW states correctly for kexec
- Various cleanup and style fix for QBMAN/QE/GUTS drivers

* tag 'soc-fsl-next-v5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
  soc: fsl: enable acpi support in RCPM driver
  Revert "soc: fsl: qe: introduce qe_io{read,write}* wrappers"
  tty: serial: ucc_uart: replace qe_io{read,write}* wrappers by generic io{read,write}*
  soc: fsl: qe: replace qe_io{read,write}* wrappers by generic io{read,write}*
  soc: fsl: guts: fix comment syntax in file
  soc: fsl: guts: remove unneeded semicolon
  soc: fsl: qe: Use DEFINE_SPINLOCK() for spinlock
  soc: fsl: qbman: Delete useless kfree code
  soc: fsl: qbman: Ensure device cleanup is run for kexec

Link: https://lore.kernel.org/r/20210409205719.27927-1-leoyang.li@nxp.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-04-13 11:06:03 +02:00
Arnd Bergmann 0a8e73301d Memory controller drivers for v5.13 - Tegra SoC
1. Few cleanups.
 2. Add debug statistics to Tegra20 memory controller.
 3. Update bindings and convert to dtschema.  This update is not
    backwards compatible (ABI break) however the broken part was added
    recently (v5.11) and there are no users of it yet.
 -----BEGIN PGP SIGNATURE-----
 
 iQJEBAABCgAuFiEE3dJiKD0RGyM7briowTdm5oaLg9cFAmBt2ZcQHGtyemtAa2Vy
 bmVsLm9yZwAKCRDBN2bmhouD12sfEACQYS2TjPwHXmo9hv+fKoYAq4qQ/NOL7YAY
 pN1k42RsDa28/KwoToFkD2WFNpDppSVHVQYjLMjBhjwh7A2x8DOFufm4kOVuhOxI
 u9BAo8iasKh+gmrdLgHcWNXkm881V4mFwSYR+FLQCvrF+1O+CFc1xJ3l9CMMKAvI
 ukJBwriJ2HFWnWXiv0xRTJkjhO8/hK+AuGHLeU0EhskFUIYhaPOm8lQ75KLx6axU
 LFh5lv56zPZcXihWKU1Au3S4Wxb/FEmqkL5HVgqkNEaZYRZH8JhIR2cV5iUukA2o
 ZdWPXaSNtHn7vXAXI+VjRj10+l+qYqktSXv9ukOmd/ofQN6aYDzb0HdPM/QBw/Kz
 VNSK2bPe912oN8a9nD2rePqS/Ny8+AZz0mLkmUbVmhJWuD483pLHZAhK1zyl2Toe
 Zj5l4hSFTUwjr4UBLBlKZmBmz3sYyYUT9k/PDYU+AX52uUPLAdC0piyoEVKZxVDB
 P3XUdAZlhde/BKwVpyBNCDoWgD4SEJfSw7BOYbfVvIyaOBqxh8foMX1C+xCfaxW2
 /dYCDtdjfqSWr2rwiNNtgA8XqiFKeJwthez6xsUHvI7qxPHRRhFCZlLUk0EK9X5h
 hPyESPu01BuXzjp4w4rIX3K4t2ikBDXXOqrdlRr/8C2/Xzk6XQ4VOk/pqFk47hWk
 oJJ3Jg+Nfw==
 =bbW2
 -----END PGP SIGNATURE-----

Merge tag 'memory-controller-drv-tegra-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl into arm/drivers

Memory controller drivers for v5.13 - Tegra SoC

1. Few cleanups.
2. Add debug statistics to Tegra20 memory controller.
3. Update bindings and convert to dtschema.  This update is not
   backwards compatible (ABI break) however the broken part was added
   recently (v5.11) and there are no users of it yet.

* tag 'memory-controller-drv-tegra-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
  dt-bindings: memory: tegra20: mc: Convert to schema
  dt-bindings: memory: tegra124: emc: Replace core regulator with power domain
  dt-bindings: memory: tegra30: emc: Replace core regulator with power domain
  dt-bindings: memory: tegra20: emc: Replace core regulator with power domain
  memory: tegra: Print out info-level once per driver probe
  memory: tegra20: Protect debug code with a lock
  memory: tegra20: Correct comment to MC_STAT registers writes
  memory: tegra20: Add debug statistics
  memory: tegra: replace DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE

Link: https://lore.kernel.org/r/20210407161333.73013-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-04-08 17:47:49 +02:00
Andy Shevchenko a460513ed4 time64.h: Consolidated PSEC_PER_SEC definition
We have currently three users of the PSEC_PER_SEC each of them defining it
individually. Instead, move it to time64.h to be available for everyone.

There is a new user coming with the same constant in use. It will also
make its life easier.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-04-06 16:32:17 -07:00
Christophe Leroy ccdfc4ae4d Revert "soc: fsl: qe: introduce qe_io{read,write}* wrappers"
This reverts commit 6ac9b61786.

This commit was required because at that time, ioread/iowrite
functions were sub-optimal on powerpc/32 compared to the
architecture specific in_/out_ IO accessors.

But there are now equivalent since
commit 894fa235eb ("powerpc: inline iomap accessors").

Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
2021-04-06 15:40:48 -05:00
Dmitry Osipenko fbd31f5aa6 memory: tegra20: Add debug statistics
Add debug statistics collection support. The statistics is available
via debugfs in '/sys/kernel/debug/mc/stats', it shows percent of memory
controller utilization for each memory client. This information is
intended to help with debugging of memory performance issues, it already
was proven to be useful by helping to improve memory bandwidth management
of the display driver.

Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210319130933.23261-1-digetx@gmail.com
2021-04-01 19:58:22 +02:00
Lee Jones 41dbf4a146 ARM: at91: pm: Move prototypes to mutually included header
Both the caller and the supplier's source file should have access to
the include file containing the prototypes.

Fixes the following W=1 kernel build warning(s):

 drivers/pinctrl/pinctrl-at91.c:1637:6: warning: no previous prototype for ‘at91_pinctrl_gpio_suspend’ [-Wmissing-prototypes]
 1637 | void at91_pinctrl_gpio_suspend(void)
 | ^~~~~~~~~~~~~~~~~~~~~~~~~
 drivers/pinctrl/pinctrl-at91.c:1661:6: warning: no previous prototype for ‘at91_pinctrl_gpio_resume’ [-Wmissing-prototypes]
 1661 | void at91_pinctrl_gpio_resume(void)
 | ^~~~~~~~~~~~~~~~~~~~~~~~

Cc: Russell King <linux@armlinux.org.uk>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20210303124149.3149511-1-lee.jones@linaro.org
2021-03-26 18:20:49 +01:00
Vladimir Oltean e4bd44e89d net: ocelot: replay switchdev events when joining bridge
The premise of this change is that the switchdev port attributes and
objects offloaded by ocelot might have been missed when we are joining
an already existing bridge port, such as a bonding interface.

The patch pulls these switchdev attributes and objects from the bridge,
on behalf of the 'bridge port' net device which might be either the
ocelot switch interface, or the bonding upper interface.

The ocelot_net.c belongs strictly to the switchdev ocelot driver, while
ocelot.c is part of a library shared with the DSA felix driver.
The ocelot_port_bridge_leave function (part of the common library) used
to call ocelot_port_vlan_filtering(false), something which is not
necessary for DSA, since the framework deals with that already there.
So we move this function to ocelot_switchdev_unsync, which is specific
to the switchdev driver.

The code movement described above makes ocelot_port_bridge_leave no
longer return an error code, so we change its type from int to void.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-23 14:49:06 -07:00
Nicolas Saenz Julienne f663204c9a firmware: raspberrypi: Introduce devm_rpi_firmware_get()
It'll simplify the firmware handling for most consumers.

Suggested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2021-03-22 17:59:51 +01:00
Nicolas Saenz Julienne 1e7c57355a firmware: raspberrypi: Keep count of all consumers
When unbinding the firmware device we need to make sure it has no
consumers left. Otherwise we'd leave them with a firmware handle
pointing at freed memory.

Keep a reference count of all consumers and introduce rpi_firmware_put()
which will permit automatically decrease the reference count upon
unbinding consumer drivers.

Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
2021-03-22 17:59:51 +01:00
Vladimir Oltean df291e54cc net: ocelot: support multiple bridges
The ocelot switches are a bit odd in that they do not have an STP state
to put the ports into. Instead, the forwarding configuration is delayed
from the typical port_bridge_join into stp_state_set, when the port enters
the BR_STATE_FORWARDING state.

I can only guess that the implementation of this quirk is the reason that
led to the simplification of the driver such that only one bridge could
be offloaded at a time.

We can simplify the data structures somewhat, and introduce a per-port
bridge device pointer and STP state, similar to how the LAG offload
works now (there we have a per-port bonding device pointer and TX
enabled state). This allows offloading multiple bridges with relative
ease, while still keeping in place the quirk to delay the programming of
the PGIDs.

We actually need this change now because we need to remove the bogus
restriction from ocelot_bridge_stp_state_set that ocelot->bridge_mask
needs to contain BIT(port), otherwise that function is a no-op.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-18 19:13:42 -07:00
Horatiu Vultur 7c588c3e96 net: ocelot: Extend MRP
This patch extends MRP support for Ocelot. It allows to have multiple
rings and when the node has the MRC role it forwards MRP Test frames in
HW. For MRM there is no change.

Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-16 15:49:52 -07:00
Horatiu Vultur ebb1bb4013 net: ocelot: Add PGID_BLACKHOLE
Add a new PGID that is used not to forward frames anywhere. It is used
by MRP to make sure that MRP Test frames will not reach CPU port.

Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-03-16 15:49:52 -07:00
Linus Torvalds 8b83369ddc RISC-V Patches for the 5.12 Merge Window
I have a handful of new RISC-V related patches for this merge window:
 
 * A check to ensure drivers are properly using uaccess.  This isn't
   manifesting with any of the drivers I'm currently using, but may catch
   errors in new drivers.
 * Some preliminary support for the FU740, along with the HiFive
   Unleashed it will appear on.
 * NUMA support for RISC-V, which involves making the arm64 code generic.
 * Support for kasan on the vmalloc region.
 * A handful of new drivers for the Kendryte K210, along with the DT
   plumbing required to boot on a handful of K210-based boards.
 * Support for allocating ASIDs.
 * Preliminary support for kernels larger than 128MiB.
 * Various other improvements to our KASAN support, including the
   utilization of huge pages when allocating the KASAN regions.
 
 We may have already found a bug with the KASAN_VMALLOC code, but it's
 passing my tests.  There's a fix in the works, but that will probably
 miss the merge window.
 -----BEGIN PGP SIGNATURE-----
 
 iQJHBAABCgAxFiEEKzw3R0RoQ7JKlDp6LhMZ81+7GIkFAmA4hXATHHBhbG1lckBk
 YWJiZWx0LmNvbQAKCRAuExnzX7sYifryD/0SfXGOfj93Cxq7I7AYhhzCN7lJ5jvv
 iEQScTlPqU9nfvYodo4EDq0fp+5LIPpTL/XBHtqVjzv0FqRNa28Ea0K7kO8HuXc4
 BaUd0m/DqyB4Gfgm4qjc5bDneQ1ZYxVXprYERWNQ5Fj+tdWhaQGOW64N/TVodjjj
 NgJtTqbIAcjJqjUtttM8TZN5U1TgwLo+KCqw3iYW12lV1YKBBuvrwvSdD6jnFdIQ
 AzG/wRGZhxLoFxgBB/NEsZxDoSd6ztiwxLhS9lX4okZVsryyIdOE70Q/MflfiTlU
 xE+AdxQXTMUiiqYSmHeDD6PDb57GT/K3hnjI1yP+lIZpbInsi29JKow1qjyYjfHl
 9cSSKYCIXHL7jKU6pgt34G1O5N5+fgqHQhNbfKvlrQ2UPlfs/tWdKHpFIP/z9Jlr
 0vCAou7NSEB9zZGqzO63uBLXoN8yfL8FT3uRnnRvoRpfpex5dQX2QqPLQ7327D7N
 GUG31nd1PHTJPdxJ1cI4SO24PqPpWDWY9uaea+0jv7ivGClVadZPco/S3ZKloguT
 lazYUvyA4oRrSAyln785Rd8vg4CinqTxMtIyZbRMbNkgzVQARi9a8rjvu4n9qms2
 2wlXDFi8nR8B4ih5n79dSiiLM9ay9GJDxMcf9VxIxSAYZV2fJALnpK6gV2fzRBUe
 +k/uv8BIsFmlwQ==
 =CutX
 -----END PGP SIGNATURE-----

Merge tag 'riscv-for-linus-5.12-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux

Pull RISC-V updates from Palmer Dabbelt:
 "A handful of new RISC-V related patches for this merge window:

   - A check to ensure drivers are properly using uaccess. This isn't
     manifesting with any of the drivers I'm currently using, but may
     catch errors in new drivers.

   - Some preliminary support for the FU740, along with the HiFive
     Unleashed it will appear on.

   - NUMA support for RISC-V, which involves making the arm64 code
     generic.

   - Support for kasan on the vmalloc region.

   - A handful of new drivers for the Kendryte K210, along with the DT
     plumbing required to boot on a handful of K210-based boards.

   - Support for allocating ASIDs.

   - Preliminary support for kernels larger than 128MiB.

   - Various other improvements to our KASAN support, including the
     utilization of huge pages when allocating the KASAN regions.

  We may have already found a bug with the KASAN_VMALLOC code, but it's
  passing my tests. There's a fix in the works, but that will probably
  miss the merge window.

* tag 'riscv-for-linus-5.12-mw0' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (75 commits)
  riscv: Improve kasan population by using hugepages when possible
  riscv: Improve kasan population function
  riscv: Use KASAN_SHADOW_INIT define for kasan memory initialization
  riscv: Improve kasan definitions
  riscv: Get rid of MAX_EARLY_MAPPING_SIZE
  soc: canaan: Sort the Makefile alphabetically
  riscv: Disable KSAN_SANITIZE for vDSO
  riscv: Remove unnecessary declaration
  riscv: Add Canaan Kendryte K210 SD card defconfig
  riscv: Update Canaan Kendryte K210 defconfig
  riscv: Add Kendryte KD233 board device tree
  riscv: Add SiPeed MAIXDUINO board device tree
  riscv: Add SiPeed MAIX GO board device tree
  riscv: Add SiPeed MAIX DOCK board device tree
  riscv: Add SiPeed MAIX BiT board device tree
  riscv: Update Canaan Kendryte K210 device tree
  dt-bindings: add resets property to dw-apb-timer
  dt-bindings: fix sifive gpio properties
  dt-bindings: update sifive uart compatible string
  dt-bindings: update sifive clint compatible string
  ...
2021-02-26 10:28:35 -08:00
Damien Le Moal c6ca7616f7
clk: Add RISC-V Canaan Kendryte K210 clock driver
Add a clock provider driver for the Canaan Kendryte K210 RISC-V SoC.
This new driver with the compatible string "canaan,k210-clk" implements
support for the full clock structure of the K210 SoC. Since it is
required for the correct operation of the SoC, this driver is
selected by default for compilation when the SOC_CANAAN option is
selected.

With this change, the k210-sysctl driver is turned into a simple
platform driver which enables its power bus clock and triggers
populating its child nodes. The sysctl driver retains the SOC early
initialization code, but the implementation now relies on the new
function k210_clk_early_init() provided by the new clk-k210 driver.

The clock structure implemented and many of the coding ideas for the
driver come from the work by Sean Anderson on the K210 support for the
U-Boot project.

Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: linux-clk@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
2021-02-22 17:51:04 -08:00
Linus Torvalds d652ea30ba IOMMU Updates for Linux v5.12
Including:
 
 	- ARM SMMU and Mediatek updates from Will Deacon:
 
 		- Support for MT8192 IOMMU from Mediatek
 
 		- Arm v7s io-pgtable extensions for MT8192
 
 		- Removal of TLBI_ON_MAP quirk
 
 		- New Qualcomm compatible strings
 
 		- Allow SVA without hardware broadcast TLB maintenance
 		  on SMMUv3
 
 		- Virtualization Host Extension support for SMMUv3 (SVA)
 
 		- Allow SMMUv3 PMU (perf) driver to be built
 		  independently from IOMMU
 
 	- Some tidy-up in IOVA and core code
 
 	- Conversion of the AMD IOMMU code to use the generic
 	  IO-page-table framework
 
 	- Intel VT-d updates from Lu Baolu:
 
 		- Audit capability consistency among different IOMMUs
 
 		- Add SATC reporting structure support
 
 		- Add iotlb_sync_map callback support
 
 	- SDHI Support for Renesas IOMMU driver
 
 	- Misc Cleanups and other small improvments
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCAAdFiEEr9jSbILcajRFYWYyK/BELZcBGuMFAmAz2AcACgkQK/BELZcB
 GuMflRAAyOfXzFqfmniYKxXmxAhOIlibCoojXzecItifdyaFkvUhxCadRg5u3dLH
 IeACDvUiaA5VQnVhjI0a7gCckKdq5YDwwAS+GQICUKNEZtWwrHwm2QTRBmL9MOlA
 v+iTrhYCqZWIAPe16BP5L4u6q4JWS2N9oNmDp6ia1VIhPjfsHU+gXpYKSxiLicmV
 VECAHJk5/JrwKXBP2nMg3ZqGz9RoJc2CzC4zvKu7ADDB9Zl+pXs74mb4ta81Y3G4
 vf07G/ORYJjbMskz5KcmYw2897I9ejMrNaHrYNjlh2IDpGqmoCJ4+8vuVO0zslrm
 GzMOHMshaI653BmuRDHyczwNrNxMxSX3NOeR2fp76d3MSouK7RoFMr7ghMAegp1u
 qmSrqFbgnOT4cdzN8QpPyU22lmVHtQHm0P4EpZZzC95dtJo1nzt8BFrDjPdJDOyZ
 D7oKvZq+OA6MtjCN4gZ2ClxQoiUZ8E/jP1uGIknpzR1oeWnyEFtx8aI9q4yRjNcp
 n8UR7wFqbOIV0O/QC7UlEp/xSpG7BDN4BkvIgbH2qe6LmRmejCrnUWv6pkmPc9sI
 wFgV/Qnh9oo7yf6zvmCsi1r0kmfGLPRe8GB9+eN3wY3xxzDOLJEJNdVghWaP8Rz7
 MBcL/0u8+fMfQlRiOPX64BSIF7fFPY0r0+erINawf1VUbyjUsUE=
 =xSX1
 -----END PGP SIGNATURE-----

Merge tag 'iommu-updates-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu

Pull iommu updates from Joerg Roedel:

 - ARM SMMU and Mediatek updates from Will Deacon:
     - Support for MT8192 IOMMU from Mediatek
     - Arm v7s io-pgtable extensions for MT8192
     - Removal of TLBI_ON_MAP quirk
     - New Qualcomm compatible strings
     - Allow SVA without hardware broadcast TLB maintenance on SMMUv3
     - Virtualization Host Extension support for SMMUv3 (SVA)
     - Allow SMMUv3 PMU perf driver to be built independently from IOMMU

 - Some tidy-up in IOVA and core code

 - Conversion of the AMD IOMMU code to use the generic IO-page-table
   framework

 - Intel VT-d updates from Lu Baolu:
     - Audit capability consistency among different IOMMUs
     - Add SATC reporting structure support
     - Add iotlb_sync_map callback support

 - SDHI support for Renesas IOMMU driver

 - Misc cleanups and other small improvments

* tag 'iommu-updates-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (94 commits)
  iommu/amd: Fix performance counter initialization
  MAINTAINERS: repair file pattern in MEDIATEK IOMMU DRIVER
  iommu/mediatek: Fix error code in probe()
  iommu/mediatek: Fix unsigned domid comparison with less than zero
  iommu/vt-d: Parse SATC reporting structure
  iommu/vt-d: Add new enum value and structure for SATC
  iommu/vt-d: Add iotlb_sync_map callback
  iommu/vt-d: Move capability check code to cap_audit files
  iommu/vt-d: Audit IOMMU Capabilities and add helper functions
  iommu/vt-d: Fix 'physical' typos
  iommu: Properly pass gfp_t in _iommu_map() to avoid atomic sleeping
  iommu/vt-d: Fix compile error [-Werror=implicit-function-declaration]
  driver/perf: Remove ARM_SMMU_V3_PMU dependency on ARM_SMMU_V3
  MAINTAINERS: Add entry for MediaTek IOMMU
  iommu/mediatek: Add mt8192 support
  iommu/mediatek: Remove unnecessary check in attach_device
  iommu/mediatek: Support master use iova over 32bit
  iommu/mediatek: Add iova reserved function
  iommu/mediatek: Support for multi domains
  iommu/mediatek: Add get_domain_id from dev->dma_range_map
  ...
2021-02-22 10:31:29 -08:00
Linus Torvalds e767b3530a ARM: SoC drivers for v5.12
Updates for SoC specific drivers include a few subsystems that
 have their own maintainers but send them through the soc tree:
 
 SCMI firmware:
  - add support for a completion interrupt
 
 Reset controllers:
  - new driver for BCM4908
  - new devm_reset_control_get_optional_exclusive_released()
    function
 
 Memory controllers:
  - Renesas RZ/G2 support
  - Tegra124 interconnect support
  - Allow more drivers to be loadable modules
 
 TEE/optee firmware:
  - minor code cleanup
 
 The other half of this is SoC specific drivers that do not
 belong into any other subsystem, most of them living in
 drivers/soc:
 
  - Allwinner/sunxi power management work
  - Allwinner H616 support
 
  - ASpeed AST2600 system identification support
 
  - AT91 SAMA7G5 SoC ID driver
  - AT91 SoC driver cleanups
 
  - Broadcom BCM4908 power management bus support
 
  - Marvell mbus cleanups
 
  - Mediatek MT8167 power domain support
 
  - Qualcomm socinfo driver support for PMIC
  - Qualcomm SoC identification for many more products
 
  - TI Keystone driver cleanups for PRUSS and elsewhere
 
 Signed-off-by: Arnd Bergmann <arnd@arndb.de>
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEiK/NIGsWEZVxh/FrYKtH/8kJUicFAmApjS8ACgkQYKtH/8kJ
 UidDyw/6ArE2RWN1qk3GJbQKdCYQdqH4Ig/Nc9LA977ul2BX/BohYoEGCoveH5cG
 16FaYK8tYDCSoTfS0+w1Y8r6TgZKcV6GCM0xLSVtaihk2CO81sUfDFBIppJd614a
 2lGx9DW7205ql4vGcQsK31ncr0hVviHG2e8lOEbFc9SkQpmYuLF1dxW2JK9oWGe2
 rLXHKb20N7AvgN8Y6V0YAOGNpu9MOnx0TbTGn6SMgzIKMkpYaSs/oZY11d9jrn7Y
 m/iIahRWzLFR/lYdrD7Jowpy2A/lcwPdQlRkOiuF1s6FFCqxe1yQsrpcbt/7fXes
 UzOyE494GZFtO0zjFuwglsmiAZDMwO/fQVrIzSGV0SXF8LJpiYYTG1b3Yv5SY5Hr
 r7EF4A7GlmNmd6K1HrXTYJz9tr4oxLDw+9LZGx74JV8x0iK3cd1hRTXb1SbspA6h
 S/KRQsuEjpAyQ6xXWVp2fp6VxZkrjIpPavbcQw2RsoBnbNdrcXahTk96JfpWYGjH
 iyJkEKmCF6/w/s5+xQfy+DYepxFDO0YsPbM7kL5qhaY83KBMOHKJFCUZVWj7md5w
 QIVTeeiSewIlT5bG9XyjIfmsImq1acqTW+QCaxCnvMSsZDBbdhTMK48GwyN9U9+x
 jdQCPQye3TKL2WU6U40FPNIr08QcNy4vmJp4fMqwK5xO3+P+Zhs=
 =I2Zn
 -----END PGP SIGNATURE-----

Merge tag 'arm-drivers-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC driver updates from Arnd Bergmann:
 "Updates for SoC specific drivers include a few subsystems that have
  their own maintainers but send them through the soc tree:

  SCMI firmware:
   - add support for a completion interrupt

  Reset controllers:
   - new driver for BCM4908
   - new devm_reset_control_get_optional_exclusive_released() function

  Memory controllers:
   - Renesas RZ/G2 support
   - Tegra124 interconnect support
   - Allow more drivers to be loadable modules

  TEE/optee firmware:
   - minor code cleanup

  The other half of this is SoC specific drivers that do not belong into
  any other subsystem, most of them living in drivers/soc:

   - Allwinner/sunxi power management work
   - Allwinner H616 support

   - ASpeed AST2600 system identification support

   - AT91 SAMA7G5 SoC ID driver
   - AT91 SoC driver cleanups

   - Broadcom BCM4908 power management bus support

   - Marvell mbus cleanups

   - Mediatek MT8167 power domain support

   - Qualcomm socinfo driver support for PMIC
   - Qualcomm SoC identification for many more products

   - TI Keystone driver cleanups for PRUSS and elsewhere"

* tag 'arm-drivers-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (89 commits)
  soc: aspeed: socinfo: Add new systems
  soc: aspeed: snoop: Add clock control logic
  memory: tegra186-emc: Replace DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE
  memory: samsung: exynos5422-dmc: Correct function names in kerneldoc
  memory: ti-emif-pm: Drop of_match_ptr from of_device_id table
  optee: simplify i2c access
  drivers: soc: atmel: fix type for same7
  tee: optee: remove need_resched() before cond_resched()
  soc: qcom: ocmem: don't return NULL in of_get_ocmem
  optee: sync OP-TEE headers
  tee: optee: fix 'physical' typos
  drivers: optee: use flexible-array member instead of zero-length array
  tee: fix some comment typos in header files
  soc: ti: k3-ringacc: Use of_device_get_match_data()
  soc: ti: pruss: Refactor the CFG sub-module init
  soc: mediatek: pm-domains: Don't print an error if child domain is deferred
  soc: mediatek: pm-domains: Add domain regulator supply
  dt-bindings: power: Add domain regulator supply
  soc: mediatek: cmdq: Remove cmdq_pkt_flush()
  soc: mediatek: pm-domains: Add support for mt8167
  ...
2021-02-20 18:42:28 -08:00
Horatiu Vultur d8ea7ff399 net: mscc: ocelot: Add support for MRP
Add basic support for MRP. The HW will just trap all MRP frames on the
ring ports to CPU and allow the SW to process them. In this way it is
possible to for this node to behave both as MRM and MRC.

Current limitations are:
- it doesn't support Interconnect roles.
- it supports only a single ring.
- the HW should be able to do forwarding of MRP Test frames so the SW
  will not need to do this. So it would be able to have the role MRC
  without SW support.

Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-02-16 14:47:46 -08:00
Vladimir Oltean 0a6f17c6ae net: dsa: tag_ocelot_8021q: add support for PTP timestamping
For TX timestamping, we use the felix_txtstamp method which is common
with the regular (non-8021q) ocelot tagger. This method says that skb
deferral is needed, prepares a timestamp request ID, and puts a clone of
the skb in a queue waiting for the timestamp IRQ.

felix_txtstamp is called by dsa_skb_tx_timestamp() just before the
tagger's xmit method. In the tagger xmit, we divert the packets
classified by dsa_skb_tx_timestamp() as PTP towards the MMIO-based
injection registers, and we declare them as dead towards dsa_slave_xmit.
If not PTP, we proceed with normal tag_8021q stuff.

Then the timestamp IRQ fires, the clone queued up from felix_txtstamp is
matched to the TX timestamp retrieved from the switch's FIFO based on
the timestamp request ID, and the clone is delivered to the stack.

On RX, thanks to the VCAP IS2 rule that redirects the frames with an
EtherType for 1588 towards two destinations:
- the CPU port module (for MMIO based extraction) and
- if the "no XTR IRQ" workaround is in place, the dsa_8021q CPU port
the relevant data path processing starts in the ptp_classify_raw BPF
classifier installed by DSA in the RX data path (post tagger, which is
completely unaware that it saw a PTP packet).

This time we can't reuse the same implementation of .port_rxtstamp that
also works with the default ocelot tagger. That is because felix_rxtstamp
is given an skb with a freshly stripped DSA header, and it says "I don't
need deferral for its RX timestamp, it's right in it, let me show you";
and it just points to the header right behind skb->data, from where it
unpacks the timestamp and annotates the skb with it.

The same thing cannot happen with tag_ocelot_8021q, because for one
thing, the skb did not have an extraction frame header in the first
place, but a VLAN tag with no timestamp information. So the code paths
in felix_rxtstamp for the regular and 8021q tagger are completely
independent. With tag_8021q, the timestamp must come from the packet's
duplicate delivered to the CPU port module, but there is potentially
complex logic to be handled [ and prone to reordering ] if we were to
just start reading packets from the CPU port module, and try to match
them to the one we received over Ethernet and which needs an RX
timestamp. So we do something simple: we tell DSA "give me some time to
think" (we request skb deferral by returning false from .port_rxtstamp)
and we just drop the frame we got over Ethernet with no attempt to match
it to anything - we just treat it as a notification that there's data to
be processed from the CPU port module's queues. Then we proceed to read
the packets from those, one by one, which we deliver up the stack,
timestamped, using netif_rx - the same function that any driver would
use anyway if it needed RX timestamp deferral. So the assumption is that
we'll come across the PTP packet that triggered the CPU extraction
notification eventually, but we don't know when exactly. Thanks to the
VCAP IS2 trap/redirect rule and the exclusion of the CPU port module
from the flooding replicators, only PTP frames should be present in the
CPU port module's RX queues anyway.

There is just one conflict between the VCAP IS2 trapping rule and the
semantics of the BPF classifier. Namely, ptp_classify_raw() deems
general messages as non-timestampable, but still, those are trapped to
the CPU port module since they have an EtherType of ETH_P_1588. So, if
the "no XTR IRQ" workaround is in place, we need to run another BPF
classifier on the frames extracted over MMIO, to avoid duplicates being
sent to the stack (once over Ethernet, once over MMIO). It doesn't look
like it's possible to install VCAP IS2 rules based on keys extracted
from the 1588 frame headers.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-02-14 17:31:44 -08:00
Vladimir Oltean 924ee317f7 net: mscc: ocelot: refactor ocelot_xtr_irq_handler into ocelot_xtr_poll
Since the felix DSA driver will need to poll the CPU port module for
extracted frames as well, let's create some common functions that read
an Extraction Frame Header, and then an skb, from a CPU extraction
group.

We abuse the struct ocelot_ops :: port_to_netdev function a little bit,
in order to retrieve the DSA port net_device or the ocelot switchdev
net_device based on the source port information from the Extraction
Frame Header, but it's all in the benefit of code simplification -
netdev_alloc_skb needs it. Originally, the port_to_netdev method was
intended for parsing act->dev from tc flower offload code.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-02-14 17:31:44 -08:00
Vladimir Oltean 40d3f295b5 net: mscc: ocelot: use common tag parsing code with DSA
The Injection Frame Header and Extraction Frame Header that the switch
prepends to frames over the NPI port is also prepended to frames
delivered over the CPU port module's queues.

Let's unify the handling of the frame headers by making the ocelot
driver call some helpers exported by the DSA tagger. Among other things,
this allows us to get rid of the strange cpu_to_be32 when transmitting
the Injection Frame Header on ocelot, since the packing API uses
network byte order natively (when "quirks" is 0).

The comments above ocelot_gen_ifh talk about setting pop_cnt to 3, and
the cpu extraction queue mask to something, but the code doesn't do it,
so we don't do it either.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-02-14 17:31:44 -08:00
Vladimir Oltean 137ffbc4bb net: mscc: ocelot: refactor ocelot_port_inject_frame out of ocelot_port_xmit
The felix DSA driver will inject some frames through register MMIO, same
as ocelot switchdev currently does. So we need to be able to reuse the
common code.

Also create some shim definitions, since the DSA tagger can be compiled
without support for the switch driver.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-02-14 17:31:44 -08:00
Vladimir Oltean 421741ea56 net: mscc: ocelot: offload bridge port flags to device
We should not be unconditionally enabling address learning, since doing
that is actively detrimential when a port is standalone and not offloading
a bridge. Namely, if a port in the switch is standalone and others are
offloading the bridge, then we could enter a situation where we learn an
address towards the standalone port, but the bridged ports could not
forward the packet there, because the CPU is the only path between the
standalone and the bridged ports. The solution of course is to not
enable address learning unless the bridge asks for it.

We need to set up the initial port flags for no learning and flooding
everything, and also when the port joins and leaves the bridge.
The flood configuration was already configured ok for standalone mode
in ocelot_init, we just need to disable learning in ocelot_init_port.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-02-12 17:08:05 -08:00
Vladimir Oltean b360d94f1b net: mscc: ocelot: use separate flooding PGID for broadcast
In preparation of offloading the bridge port flags which have
independent settings for unknown multicast and for broadcast, we should
also start reserving one destination Port Group ID for the flooding of
broadcast packets, to allow configuring it individually.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-02-12 17:08:05 -08:00
David S. Miller dc9d87581d Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net 2021-02-10 13:30:12 -08:00
Arnd Bergmann ce8ccf21c0 Qualcomm driver updates for 5.12
The socinfo driver gains support for dumping information about the platform's
 PMICs, as well as new definitions for a number of platforms. The LLCC driver
 gains SM8250 support, AOSS QMP gains SM8350 support and the RPMPD driver gains
 support for MSM8994 power domains. In addition to this it contains a few minor
 fixes in the ocmem, rpmh and llcc drivers.
 -----BEGIN PGP SIGNATURE-----
 
 iQJPBAABCAA5FiEEBd4DzF816k8JZtUlCx85Pw2ZrcUFAmAbg1wbHGJqb3JuLmFu
 ZGVyc3NvbkBsaW5hcm8ub3JnAAoJEAsfOT8Nma3FYYEP/R2zxLPj1ntJmyLV/MWX
 bioEGJWXKk60b2k5lAai2nwD/iswPqMyRtI3eXub7YVoYPRVMDHVl7nuGE83hHES
 r3OUCTisiM5VCOIYjzs9ZJJx4ceGzicsXoV2eEZUabQ4pg2/VHzdbh3DmH+Yh7hL
 PTgEiAYqQRSpRlFTf7ByccuqjAMyhs1GJ3Ajrl9dACsXIrT8ktPqk1UZ6JDl7w+3
 iox86p6EzpcnzgMY1APNgAoMDqHNOMbZky5zvgWEdMXGnpBZGjY8l1XXzIG9ZjE2
 o9u9DnxnCyBJoaxqbsBeHmFux2QCNTggQc4k5fd4BI0vFLR5X4sTyhcG2rEy12st
 LUaSKP9hb4M4JTkbMCvKAgae1FrMArLXAExhsoXopa2QwV0JwbtlE1onaOE4hsGT
 9YmBuJD6auegplIroGbOEihoNrOhPWEiNCX8N9I0daPewY/ulzxqn57Blq1RVXmV
 xs3ifBVyiFTbTD/cFvyDKnLDbgPuaT1bUReG6QHZYzOO/vzshe6JkduNY/RRgRd/
 l/ENBkZ70yQRvImIcbzRgmq767u7zGa7VWrwTmLOe8+5VxxosxZD1sYBioO9N2uL
 pZ5kfAeEAfhn70SX+12SMYIMKxNuvVSCesQNNoBHyMAQX6Y0pbuAyEEyrRdcgodO
 lT1qpN+V2lkjlmzWEiokI3V0
 =rWBX
 -----END PGP SIGNATURE-----

Merge tag 'qcom-drivers-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/drivers

Qualcomm driver updates for 5.12

The socinfo driver gains support for dumping information about the platform's
PMICs, as well as new definitions for a number of platforms. The LLCC driver
gains SM8250 support, AOSS QMP gains SM8350 support and the RPMPD driver gains
support for MSM8994 power domains. In addition to this it contains a few minor
fixes in the ocmem, rpmh and llcc drivers.

* tag 'qcom-drivers-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
  soc: qcom: ocmem: don't return NULL in of_get_ocmem
  soc: qcom: socinfo: Remove unwanted le32_to_cpu()
  soc: qcom: aoss: Add SM8350 compatible
  drivers: soc: qcom: rpmpd: Add msm8994 RPM Power Domains
  soc: qcom: socinfo: Fix an off by one in qcom_show_pmic_model()
  soc: qcom: socinfo: Fix off-by-one array index bounds check
  soc: qcom: socinfo: Add MDM9607 IDs
  soc: qcom: socinfo: Add SoC IDs for APQ/MSM8998
  soc: qcom: socinfo: Add SoC IDs for 630 family
  soc: qcom: socinfo: Open read access to all for debugfs
  soc: qcom: socinfo: add info from PMIC models array
  soc: qcom: socinfo: add several PMIC IDs
  soc: qcom: socinfo: add qrb5165 SoC ID
  soc: qcom: rpmh: Remove serialization of TCS commands
  soc: qcom: smem: use %*ph to print small buffer
  dt-bindings: soc: qcom: convert qcom,smem bindings to yaml
  drivers: qcom: rpmh-rsc: Do not read back the register write on trigger
  soc: qcom: llcc-qcom: Add support for SM8250 SoC
  soc: qcom: llcc-qcom: Extract major hardware version
  dt-bindings: msm: Add LLCC for SM8250

Link: https://lore.kernel.org/r/20210204052258.388890-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-02-10 00:14:14 +01:00
Vladimir Oltean eb4733d7cf net: dsa: felix: implement port flushing on .phylink_mac_link_down
There are several issues which may be seen when the link goes down while
forwarding traffic, all of which can be attributed to the fact that the
port flushing procedure from the reference manual was not closely
followed.

With flow control enabled on both the ingress port and the egress port,
it may happen when a link goes down that Ethernet packets are in flight.
In flow control mode, frames are held back and not dropped. When there
is enough traffic in flight (example: iperf3 TCP), then the ingress port
might enter congestion and never exit that state. This is a problem,
because it is the egress port's link that went down, and that has caused
the inability of the ingress port to send packets to any other port.
This is solved by flushing the egress port's queues when it goes down.

There is also a problem when performing stream splitting for
IEEE 802.1CB traffic (not yet upstream, but a sort of multicast,
basically). There, if one port from the destination ports mask goes
down, splitting the stream towards the other destinations will no longer
be performed. This can be traced down to this line:

	ocelot_port_writel(ocelot_port, 0, DEV_MAC_ENA_CFG);

which should have been instead, as per the reference manual:

	ocelot_port_rmwl(ocelot_port, 0, DEV_MAC_ENA_CFG_RX_ENA,
			 DEV_MAC_ENA_CFG);

Basically only DEV_MAC_ENA_CFG_RX_ENA should be disabled, but not
DEV_MAC_ENA_CFG_TX_ENA - I don't have further insight into why that is
the case, but apparently multicasting to several ports will cause issues
if at least one of them doesn't have DEV_MAC_ENA_CFG_TX_ENA set.

I am not sure what the state of the Ocelot VSC7514 driver is, but
probably not as bad as Felix/Seville, since VSC7514 uses phylib and has
the following in ocelot_adjust_link:

	if (!phydev->link)
		return;

therefore the port is not really put down when the link is lost, unlike
the DSA drivers which use .phylink_mac_link_down for that.

Nonetheless, I put ocelot_port_flush() in the common ocelot.c because it
needs to access some registers from drivers/net/ethernet/mscc/ocelot_rew.h
which are not exported in include/soc/mscc/ and a bugfix patch should
probably not move headers around.

Fixes: bdeced75b1 ("net: dsa: felix: Add PCS operations for PHYLINK")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2021-02-09 11:41:11 -08:00
Vladimir Oltean 8fe6832e96 net: dsa: felix: propagate the LAG offload ops towards the ocelot lib
The ocelot switch has been supporting LAG offload since its initial
commit, however felix could not make use of that, due to lack of a LAG
abstraction in DSA. Now that we have that, let's forward DSA's calls
towards the ocelot library, who will deal with setting up the bonding.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-02-06 14:51:51 -08:00
Vladimir Oltean 23ca3b727e net: mscc: ocelot: rebalance LAGs on link up/down events
At present there is an issue when ocelot is offloading a bonding
interface, but one of the links of the physical ports goes down. Traffic
keeps being hashed towards that destination, and of course gets dropped
on egress.

Monitor the netdev notifier events emitted by the bonding driver for
changes in the physical state of lower interfaces, to determine which
ports are active and which ones are no longer.

Then extend ocelot_get_bond_mask to return either the configured bonding
interfaces, or the active ones, depending on a boolean argument. The
code that does rebalancing only needs to do so among the active ports,
whereas the bridge forwarding mask and the logical port IDs still need
to look at the permanently bonded ports.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-02-06 14:51:51 -08:00
Vladimir Oltean 528d3f190c net: mscc: ocelot: drop the use of the "lags" array
We can now simplify the implementation by always using ocelot_get_bond_mask
to look up the other ports that are offloading the same bonding interface
as us.

In ocelot_set_aggr_pgids, the code had a way to uniquely iterate through
LAGs. We need to achieve the same behavior by marking each LAG as visited,
which we do now by using a temporary 32-bit "visited" bitmask. This is
ok and we do not need dynamic memory allocation, because we know that
this switch architecture will not have more than 32 ports (the PGID port
masks are 32-bit anyway).

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-02-06 14:51:50 -08:00
Vladimir Oltean b80af65969 net: mscc: ocelot: set up the bonding mask in a way that avoids a net_device
Since this code should be called from pure switchdev as well as from
DSA, we must find a way to determine the bonding mask not by looking
directly at the net_device lowers of the bonding interface, since those
could have different private structures.

We keep a pointer to the bonding upper interface, if present, in struct
ocelot_port. Then the bonding mask becomes the bitwise OR of all ports
that have the same bonding upper interface. This adds a duplication of
functionality with the current "lags" array, but the duplication will be
short-lived, since further patches will remove the latter completely.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-02-06 14:51:50 -08:00
Arnd Bergmann 60a64da9f0 This pull request contains Broadcom SoCs drivers changes for 5.12,
please pull the following:
 
 - Rafal adds support for the Power Management Bus (PMB) which is used in
   a variety of DSL/Cable modem/STB SoCs with a primary target being the
   4908 Wi-Fi SoC from the DSL organization. He also adds empty stubs to
   get the chip identification (family and revision) to permit the
   Broadcom STB USB PHY driver from being decoupled from ARCH_BRCMSTB
 
 - Florian removes an unused function and its header
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEm+Rq3+YGJdiR9yuFh9CWnEQHBwQFAmAXKTQACgkQh9CWnEQH
 BwSyvxAAsOVmytMHBHxe4i8Pad0Yv9sUsV0AvfvJmi0lhd0a1L7HLWBhoYq+fNFO
 R6ycuVjUb9RCA5O9nps6qnWbslEar3h5of/Ku4ovev3I5xQYiGFLOPe75ivoi+sl
 I4T9PwVuWV3WDjK8upA3naUwNzEv30Zw0uFULw5J0RFZAB3W3ObITO3mF8a3aOGc
 uVNWfD+Ro/2l1hrPfO74Qm0r36XQmvRNNOFH3gpKdBZAG2nHkQpfOsoNNUGjBjYm
 amFqm/zfc7Ydxg2WzQwUUaslyq+yIKtn919rFnudR48iHpzpotVuFKgGt3CppCl5
 oF4/1+C6bRzKErPYzn3B6JGFOYwSZwg9+TleDEv7eElIo04FBSOa6pNoHNDEfPXr
 LI9U7CL0/zf8vbkoK3txQg7fdcYvwED9/ip5u2IJ8KZvhoCu175FIZbrXIO+woPC
 gTk28bSBWH4mqGh7fPOmX3fBc2zow7xd/DlTnT1SNy6IVDZL9S82czAS/b2ImBzp
 sfK0fDFrO3cPfrE2/CrKwT/OiMOUsrc0Al7g0rmpPkFHgnrh/ZCV+zQT7RSEvL1P
 Gp3ZFkSjTbrXIZwkJ04i73sJUpC8F8F8XeoFItPs3VGXxJxsapB+b6TuW09qhkvU
 WJXD3gFUL34IXI6luB1ZWNG4/fJBHgWXIrKsBnf9kpZENfHEdKs=
 =43Gr
 -----END PGP SIGNATURE-----

Merge tag 'arm-soc/for-5.12/drivers' of https://github.com/Broadcom/stblinux into arm/drivers

This pull request contains Broadcom SoCs drivers changes for 5.12,
please pull the following:

- Rafal adds support for the Power Management Bus (PMB) which is used in
  a variety of DSL/Cable modem/STB SoCs with a primary target being the
  4908 Wi-Fi SoC from the DSL organization. He also adds empty stubs to
  get the chip identification (family and revision) to permit the
  Broadcom STB USB PHY driver from being decoupled from ARCH_BRCMSTB

- Florian removes an unused function and its header

* tag 'arm-soc/for-5.12/drivers' of https://github.com/Broadcom/stblinux:
  soc: bcm: brcmstb: Remove soc_is_brcmstb()
  soc: bcm: brcmstb: add stubs for getting platform IDs
  soc: bcm: add PM driver for Broadcom's PMB
  dt-bindings: power: document Broadcom's PMB binding

Link: https://lore.kernel.org/r/20210131221721.685974-5-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-02-02 22:22:03 +01:00
Arnd Bergmann 4d29b82686 Memory controller drivers for v5.12 - Tegra SoC
1. Make the tegra124-emc driver modular.
 2. Add interconnect support to Tegra124 memory controller drivers.
 3. Minor fixes.
 -----BEGIN PGP SIGNATURE-----
 
 iQJEBAABCgAuFiEE3dJiKD0RGyM7briowTdm5oaLg9cFAmAW7yQQHGtyemtAa2Vy
 bmVsLm9yZwAKCRDBN2bmhouD18TNEACamr2TM1zSGLu3SHrgSS3MC162ACVIee5Y
 TO+erTi63T+AgiwFgWB8liOPKVVFktS2N9PkDfzWCe58SEoNQCy0K8IAEyjl0fQK
 l7Nst3KtJrX/ui3OUimNYcJu7ap2z0Hn2RXDNhwJVeEkj3vgUc+q6v9/f9HpO59l
 te5FAKc/4waP4uCSb7XiF2i/0xkc5pHI6cBRf4zuepOcxsOOtPprBQvSVino4dbq
 rc+5tNUc27/AaxXnmvD7dgr2N6sxfPHDQ/N+nlj3BLEE/IePJyLqPKSpBlWP2DY9
 gn1x4R6MgxDwYTy/2eBkeo7aLEQEQMk1h4VPKw3dlfjay+XNht4POIFELCK16uJk
 qbg6PAx/YKcaK8BmzXHc6Zvup4VNABjwoFqSz/fkLi+sqRmyI8xclgYaIHqpt0Mx
 AdPV47QdhJYujKf5jBwSeWCfD3Y/KoYaMV41XFWuxO+bMboPhxwez4ISUuXF6SsE
 3igTU3i5x+XlNBH90cUYrEaBfjt6TudMoBcTCWN7U3oRKdDhpLuZZcYGVnn8mNC3
 MOGkIrWIypbtPvfsUqh6miDIaJdLbLJNC3bxuXd+3iOD50b+deX4WnNm144HEQ1c
 n0eRY1HagAFNJNs5dsHSB566YO9S7+B95893yJs7LxrqtwLrpJmshuw55tDO9k46
 MUyITm4Yrw==
 =t+/6
 -----END PGP SIGNATURE-----

Merge tag 'memory-controller-drv-tegra-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl into arm/drivers

Memory controller drivers for v5.12 - Tegra SoC

1. Make the tegra124-emc driver modular.
2. Add interconnect support to Tegra124 memory controller drivers.
3. Minor fixes.

* tag 'memory-controller-drv-tegra-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
  memory: tegra: Remove calls to dev_pm_opp_set_clkname()
  memory: tegra: Check whether reset is already asserted
  memory: tegra124: Support interconnect framework
  memory: tegra124-emc: Continue probing if timings are missing in device-tree
  memory: tegra124-emc: Make driver modular

Link: https://lore.kernel.org/r/20210131180109.11510-2-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-02-02 22:20:34 +01:00
Arnd Bergmann 993fd7d6fe Memory controller drivers for v5.12
1. Mediatek SMI: fix PM usage counter and make the driver modular.
 2. Renesas RPC-IF: add support for RZ/G2 series.
 3. Minor fixes.
 -----BEGIN PGP SIGNATURE-----
 
 iQJEBAABCgAuFiEE3dJiKD0RGyM7briowTdm5oaLg9cFAmAW79UQHGtyemtAa2Vy
 bmVsLm9yZwAKCRDBN2bmhouD1xz2D/9IBQzptHGrRiY83pn+J/cLTaCdontM4NMU
 2f+ShaDWv8KHdG8156eP3ycvZI6lf01kCARhh1xbpvlPTXZU4sLpO6rsQFnyczc/
 JSW5Zfs/dXjkpLAAMFJKgTtw6aG4nIyep3x28WZMgIGf1JFGkiU8W3XMIOt+iv6D
 SivG611E+BFtQQouXIRmL5H7L29nLGnw5wXayhOLeGYdi6pMC3nHT/5TZx2Ld6BO
 5fguXVO5fWroVb6M1FvB8r/l6/JP8F99+dxzg9MZTQt8AHUaxtp/zojUUk0EjI1L
 3ziNqCLE3O7YdFIVD/Ib3u9SYF+GtOpMR0M1CVP2H6O2CaAUndQfyO1cMP5g+DnR
 Fq2D60qgl6RPRhuLui8V+jE24NvI3a4woakx0XTCh7NPWYmG9BLYM4Q4ty+ZPA+N
 ncQGYgCnodFWaCWmSb9wLAvEMHL8E9ja13nYGJo5hbtP34X984lKaDrS44jVllWk
 8y6Qp+qlsIwr8X+y33C5dv0s8txlOt9M1ckkK0GOvD3F+Yr4aR7/cPYyoVv22K7h
 KjcSrbkoRc2ySycBNUq79LOaq6DYcNFje+8M8cWF8BoPddXi1piW50YbDMsu8XKF
 HbuZYMKMVUUuxxENqi00f+WJKHzlLpupP5YYJz7r16B8Wqoa+aJMEr1/lDl8pSpC
 Yo2IIQwgxg==
 =S32T
 -----END PGP SIGNATURE-----

Merge tag 'memory-controller-drv-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl into arm/drivers

Memory controller drivers for v5.12

1. Mediatek SMI: fix PM usage counter and make the driver modular.
2. Renesas RPC-IF: add support for RZ/G2 series.
3. Minor fixes.

* tag 'memory-controller-drv-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-mem-ctrl:
  memory: mtk-smi: Allow building as module
  memory: ti-aemif: Drop child node when jumping out loop
  memory: mtk-smi: Use platform_register_drivers
  memory: renesas-rpc-if: Add RZ/G2 to Kconfig description
  dt-bindings: memory: renesas,rpc-if: Add support for RZ/G2 Series
  memory: emif: Use DEFINE_SPINLOCK() for spinlock
  memory: mtk-smi: Fix PM usage counter unbalance in mtk_smi ops

Link: https://lore.kernel.org/r/20210131180109.11510-1-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2021-02-02 22:19:40 +01:00
Joerg Roedel d1e3306ba8 Arm SMMU updates for 5.12
- Support for MT8192 IOMMU from Mediatek
 
 - Arm v7s io-pgtable extensions for MT8192
 
 - Removal of TLBI_ON_MAP quirk
 
 - New Qualcomm compatible strings
 
 - Allow SVA without hardware broadcast TLB maintenance on SMMUv3
 
 - Virtualization Host Extension support for SMMUv3 (SVA)
 
 - Allow SMMUv3 PMU (perf) driver to be built independently from IOMMU
 
 - Misc cleanups
 -----BEGIN PGP SIGNATURE-----
 
 iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAmAYD/QQHHdpbGxAa2Vy
 bmVsLm9yZwAKCRC3rHDchMFjNLZjCACBK2bCmkVJfs39YeeMhHWVRyiiMpIuCvja
 7WuIqeXnbtAg19hkwPqns+XYeTTnoeo/aSZUS9z8DIDUqADMES+1UUMfVf2mfL3A
 VD1pGRtQezYS+rDOc5dL9m1CcJ2RRY5tfQEjK8Fnm5CItvylNXbURH1nfu1tMVW7
 fn1tMNKCTnY7FkABttKyR4a1XIyFX+fPdSrqd5PjQ7D6rK2ZYrorMf55WpmQEfFu
 3er4F3Xz8nJeTvswPUMNB3ibvcdICM9VcSwFHpElTq2dbHUDDz3uFQwyiXrutEmb
 Xz4UGabjS/ZEPaty6y7VxdYEbD4Q2dzii57jKKtV49N36iCvkSR2
 =5KXT
 -----END PGP SIGNATURE-----

Merge tag 'arm-smmu-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/will/linux into arm/smmu

Arm SMMU updates for 5.12

- Support for MT8192 IOMMU from Mediatek

- Arm v7s io-pgtable extensions for MT8192

- Removal of TLBI_ON_MAP quirk

- New Qualcomm compatible strings

- Allow SVA without hardware broadcast TLB maintenance on SMMUv3

- Virtualization Host Extension support for SMMUv3 (SVA)

- Allow SMMUv3 PMU (perf) driver to be built independently from IOMMU

- Misc cleanups
2021-02-02 13:35:40 +01:00
Yong Wu 8d2c749e52 iommu/mediatek: Support master use iova over 32bit
After extending v7s, our pagetable already support iova reach
16GB(34bit). the master got the iova via dma_alloc_attrs may reach
34bits, but its HW register still is 32bit. then how to set the
bit32/bit33 iova? this depend on a SMI larb setting(bank_sel).

we separate whole 16GB iova to four banks:
bank: 0: 0~4G; 1: 4~8G; 2: 8-12G; 3: 12-16G;
The bank number is (iova >> 32).

We will preassign which bank the larbs belong to. currently we don't
have a interface for master to adjust its bank number.

Each a bank is a iova_region which is a independent iommu-domain.
the iova range for each iommu-domain can't cross 4G.

Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org> #for memory part
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Link: https://lore.kernel.org/r/20210111111914.22211-31-yong.wu@mediatek.com
Signed-off-by: Will Deacon <will@kernel.org>
2021-02-01 11:31:19 +00:00
Yong Wu 66a2891554 iommu/mediatek: Use the common mtk-memory-port.h
Use the common memory header(larb-port) in the source code.

Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Link: https://lore.kernel.org/r/20210111111914.22211-9-yong.wu@mediatek.com
Signed-off-by: Will Deacon <will@kernel.org>
2021-02-01 11:31:16 +00:00
Vladimir Oltean e21268efbe net: dsa: felix: perform switch setup for tag_8021q
Unlike sja1105, the only other user of the software-defined tag_8021q.c
tagger format, the implementation we choose for the Felix DSA switch
driver preserves full functionality under a vlan_filtering bridge
(i.e. IP termination works through the DSA user ports under all
circumstances).

The tag_8021q protocol just wants:
- Identifying the ingress switch port based on the RX VLAN ID, as seen
  by the CPU. We achieve this by using the TCAM engines (which are also
  used for tc-flower offload) to push the RX VLAN as a second, outer
  tag, on egress towards the CPU port.
- Steering traffic injected into the switch from the network stack
  towards the correct front port based on the TX VLAN, and consuming
  (popping) that header on the switch's egress.

A tc-flower pseudocode of the static configuration done by the driver
would look like this:

$ tc qdisc add dev <cpu-port> clsact
$ for eth in swp0 swp1 swp2 swp3; do \
	tc filter add dev <cpu-port> egress flower indev ${eth} \
		action vlan push id <rxvlan> protocol 802.1ad; \
	tc filter add dev <cpu-port> ingress protocol 802.1Q flower
		vlan_id <txvlan> action vlan pop \
		action mirred egress redirect dev ${eth}; \
done

but of course since DSA does not register network interfaces for the CPU
port, this configuration would be impossible for the user to do. Also,
due to the same reason, it is impossible for the user to inadvertently
delete these rules using tc. These rules do not collide in any way with
tc-flower, they just consume some TCAM space, which is something we can
live with.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-01-29 21:25:27 -08:00
Vladimir Oltean cacea62fcd net: mscc: ocelot: don't use NPI tag prefix for the CPU port module
Context: Ocelot switches put the injection/extraction frame header in
front of the Ethernet header. When used in NPI mode, a DSA master would
see junk instead of the destination MAC address, and it would most
likely drop the packets. So the Ocelot frame header can have an optional
prefix, which is just "ff:ff:ff:ff:ff:fe > ff:ff:ff:ff:ff:ff" padding
put before the actual tag (still before the real Ethernet header) such
that the DSA master thinks it's looking at a broadcast frame with a
strange EtherType.

Unfortunately, a lesson learned in commit 69df578c5f ("net: mscc:
ocelot: eliminate confusion between CPU and NPI port") seems to have
been forgotten in the meanwhile.

The CPU port module and the NPI port have independent settings for the
length of the tag prefix. However, the driver is using the same variable
to program both of them.

There is no reason really to use any tag prefix with the CPU port
module, since that is not connected to any Ethernet port. So this patch
makes the inj_prefix and xtr_prefix variables apply only to the NPI
port (which the switchdev ocelot_vsc7514 driver does not use).

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-01-29 21:24:30 -08:00
Vladimir Oltean 50c6cc5b92 net: mscc: ocelot: store a namespaced VCAP filter ID
We will be adding some private VCAP filters that should not interfere in
any way with the filters added using tc-flower. So we need to allocate
some IDs which will not be used by tc.

Currently ocelot uses an u32 id derived from the flow cookie, which in
itself is an unsigned long. This is a problem in itself, since on 64 bit
systems, sizeof(unsigned long)=8, so the driver is already truncating
these.

Create a struct ocelot_vcap_id which contains the full unsigned long
cookie from tc, as well as a boolean that is supposed to namespace the
filters added by tc with the ones that aren't.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-01-29 21:24:30 -08:00
Vladimir Oltean 0e9bb4e9d9 net: mscc: ocelot: export VCAP structures to include/soc/mscc
The Felix driver will need to preinstall some VCAP filters for its
tag_8021q implementation (outside of the tc-flower offload logic), so
these need to be exported to the common includes.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-01-29 21:24:30 -08:00
Florian Fainelli 8b8f095b90 soc: bcm: brcmstb: Remove soc_is_brcmstb()
We have no in tree or out of tree users of this function, remove it and
the header providing its prototype.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2021-01-27 09:36:41 -08:00
Yong Wu 50fc8d9232 memory: mtk-smi: Allow building as module
Add support for building the SMI driver as module. Switch MTK_SMI to
tristate, and add module_exit/module_license.

Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Link: https://lore.kernel.org/r/20210126060055.11050-1-yong.wu@mediatek.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
2021-01-26 20:47:51 +01:00
Rasmus Villemoes 64a99fe596 ethernet: ucc_geth: remove bd_mem_part and all associated code
The bd_mem_part member of ucc_geth_info always has the value
MEM_PART_SYSTEM, and AFAICT, there has never been any code setting it
to any other value. Moreover, muram is a somewhat precious resource,
so there's no point using that when normal memory serves just as well.

Apart from removing a lot of dead code, this is also motivated by
wanting to clean up the "store result from kmalloc() in a u32" mess.

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-01-21 12:19:56 -08:00
Rasmus Villemoes 186b8daffb soc: fsl: qe: add cpm_muram_free_addr() helper
Add a helper that takes a virtual address rather than the muram
offset. This will be used in a couple of places to avoid having to
store both the offset and the virtual address, as well as removing
NULL checks from the callers.

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-01-21 12:19:55 -08:00
Rasmus Villemoes e8e507a8ac soc: fsl: qe: make cpm_muram_offset take a const void* argument
Allow passing const-qualified pointers without requiring a cast in the
caller.

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-01-21 12:19:55 -08:00
Vladimir Oltean f59fd9cab7 net: mscc: ocelot: configure watermarks using devlink-sb
Using devlink-sb, we can configure 12/16 (the important 75%) of the
switch's controlling watermarks for congestion drops, and we can monitor
50% of the watermark occupancies (we can monitor the reservation
watermarks, but not the sharing watermarks, which are exposed as pool
sizes).

The following definitions can be made:

SB_BUF=0 # The devlink-sb for frame buffers
SB_REF=1 # The devlink-sb for frame references
POOL_ING=0 # The pool for ingress traffic. Both devlink-sb instances
           # have one of these.
POOL_EGR=1 # The pool for egress traffic. Both devlink-sb instances
           # have one of these.

Editing the hardware watermarks is done in the following way:
BUF_xxxx_I is accessed when sb=$SB_BUF and pool=$POOL_ING
REF_xxxx_I is accessed when sb=$SB_REF and pool=$POOL_ING
BUF_xxxx_E is accessed when sb=$SB_BUF and pool=$POOL_EGR
REF_xxxx_E is accessed when sb=$SB_REF and pool=$POOL_EGR

Configuring the sharing watermarks for COL_SHR(dp=0) is done implicitly
by modifying the corresponding pool size. By default, the pool size has
maximum size, so this can be skipped.

devlink sb pool set pci/0000:00:00.5 sb $SB_BUF pool $POOL_ING \
	size 129840 thtype static

Since by default there is no buffer reservation, the above command has
maxed out BUF_COL_SHR_I(dp=0).

Configuring the per-port reservation watermark (P_RSRV) is done in the
following way:

devlink sb port pool set pci/0000:00:00.5/0 sb $SB_BUF \
	pool $POOL_ING th 1000

The above command sets BUF_P_RSRV_I(port 0) to 1000 bytes. After this
command, the sharing watermarks are internally reconfigured with 1000
bytes less, i.e. from 129840 bytes to 128840 bytes.

Configuring the per-port-tc reservation watermarks (Q_RSRV) is done in
the following way:

for tc in {0..7}; do
	devlink sb tc bind set pci/0000:00:00.5/0 sb 0 tc $tc \
		type ingress pool $POOL_ING \
		th 3000
done

The above command sets BUF_Q_RSRV_I(port 0, tc 0..7) to 3000 bytes.
The sharing watermarks are again reconfigured with 24000 bytes less.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-01-15 20:02:35 -08:00
Vladimir Oltean 6c30384eb1 net: mscc: ocelot: register devlink ports
Add devlink integration into the mscc_ocelot switchdev driver. All
physical ports (i.e. the unused ones as well) except the CPU port module
at ocelot->num_phys_ports are registered with devlink, and that requires
keeping the devlink_port structure outside struct ocelot_port_private,
since the latter has a 1:1 mapping with a struct net_device (which does
not exist for unused ports).

Since we use devlink_port_type_eth_set to link the devlink port to the
net_device, we can as well remove the .ndo_get_phys_port_name and
.ndo_get_port_parent_id implementations, since devlink takes care of
retrieving the port name and number automatically, once
.ndo_get_devlink_port is implemented.

Note that the felix DSA driver is already integrated with devlink by
default, since that is a thing that the DSA core takes care of. This is
the reason why these devlink stubs were put in ocelot_net.c and not in
the common library. It is also the reason why ocelot::devlink is a
pointer and not a full structure embedded inside struct ocelot: because
the mscc_ocelot driver allocates that by itself (as the container of
struct ocelot, in fact), but in the case of felix, it is DSA who
allocates the devlink, and felix just propagates the pointer towards
struct ocelot.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-01-15 20:02:34 -08:00
Vladimir Oltean 70d39a6e62 net: mscc: ocelot: export NUM_TC constant from felix to common switch lib
We should be moving anything that isn't DSA-specific or SoC-specific out
of the felix DSA driver, and into the common mscc_ocelot switch library.

The number of traffic classes is one of the aspects that is common
between all ocelot switches, so it belongs in the library.

This patch also makes seville use 8 TX queues, and therefore enables
prioritization via the QOS_CLASS field in the NPI injection header.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-01-15 20:02:34 -08:00
Vladimir Oltean 703b762190 net: mscc: ocelot: add ops for decoding watermark threshold and occupancy
We'll need to read back the watermark thresholds and occupancy from
hardware (for devlink-sb integration), not only to write them as we did
so far in ocelot_port_set_maxlen. So introduce 2 new functions in struct
ocelot_ops, similar to wm_enc, and implement them for the 3 supported
mscc_ocelot switches.

Remove the INUSE and MAXUSE unpacking helpers for the QSYS_RES_STAT
register, because that doesn't scale with the number of switches that
mscc_ocelot supports now. They have different bit widths for the
watermarks, and we need function pointers to abstract that difference
away.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-01-15 20:02:34 -08:00
Vladimir Oltean f6fe01d6fa net: mscc: ocelot: auto-detect packet buffer size and number of frame references
Instead of reading these values from the reference manual and writing
them down into the driver, it appears that the hardware gives us the
option of detecting them dynamically.

The number of frame references corresponds to what the reference manual
notes, however it seems that the frame buffers are reported as slightly
less than the books would indicate. On VSC9959 (Felix), the books say it
should have 128KB of packet buffer, but the registers indicate only
129840 bytes (126.79 KB). Also, the unit of measurement for FREECNT from
the documentation of all these devices is incorrect (taken from an older
generation). This was confirmed by Younes Leroul from Microchip support.

Not having anything better to do with these values at the moment* (this
will change soon), let's just print them.

*The frame buffer size is, in fact, used to calculate the tail dropping
watermarks.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-01-15 20:02:33 -08:00
Jakub Kicinski 1d9f03c0a1 Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-01-14 18:34:50 -08:00
Damien Le Moal 802fee26d8
riscv: cleanup Canaan Kendryte K210 sysctl driver
Introduce the header file include/soc/canaan/k210-sysctl.h to have a
common definition of the Canaan Kendryte K210 SoC system controller
registers. Simplify the k210 system controller driver code by removing
unused register bits definition. The MAINTAINERS file is updated,
adding the entry "CANAAN/KENDRYTE K210 SOC SYSTEM CONTROLLER DRIVER"
with myself listed as maintainer for this driver.
This is a preparatory patch for introducing the K210 clock driver. No
functional changes are introduced.

Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
2021-01-14 15:08:49 -08:00
Vladimir Oltean bae33f2b5a net: switchdev: remove the transaction structure from port attributes
Since the introduction of the switchdev API, port attributes were
transmitted to drivers for offloading using a two-step transactional
model, with a prepare phase that was supposed to catch all errors, and a
commit phase that was supposed to never fail.

Some classes of failures can never be avoided, like hardware access, or
memory allocation. In the latter case, merely attempting to move the
memory allocation to the preparation phase makes it impossible to avoid
memory leaks, since commit 91cf8eceff ("switchdev: Remove unused
transaction item queue") which has removed the unused mechanism of
passing on the allocated memory between one phase and another.

It is time we admit that separating the preparation from the commit
phase is something that is best left for the driver to decide, and not
something that should be baked into the API, especially since there are
no switchdev callers that depend on this.

This patch removes the struct switchdev_trans member from switchdev port
attribute notifier structures, and converts drivers to not look at this
member.

In part, this patch contains a revert of my previous commit 2e554a7a5d
("net: dsa: propagate switchdev vlan_filtering prepare phase to
drivers").

For the most part, the conversion was trivial except for:
- Rocker's world implementation based on Broadcom OF-DPA had an odd
  implementation of ofdpa_port_attr_bridge_flags_set. The conversion was
  done mechanically, by pasting the implementation twice, then only
  keeping the code that would get executed during prepare phase on top,
  then only keeping the code that gets executed during the commit phase
  on bottom, then simplifying the resulting code until this was obtained.
- DSA's offloading of STP state, bridge flags, VLAN filtering and
  multicast router could be converted right away. But the ageing time
  could not, so a shim was introduced and this was left for a further
  commit.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Linus Walleij <linus.walleij@linaro.org> # RTL8366RB
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-01-11 16:00:57 -08:00
Lina Iyer fef419c463 soc: qcom: rpmh: Remove serialization of TCS commands
Requests sent to RPMH can be sent as fire-n-forget or response required,
with the latter ensuring the command has been completed by the hardware
accelerator. Commands in a request with tcs_cmd::wait set, would ensure
that those select commands are sent as response required, even though
the actual TCS request may be fire-n-forget.

Also, commands with .wait flag were also guaranteed to be complete
before the following command in the TCS is sent. This means that the
next command of the same request blocked until the current request is
completed. This could mean waiting for a voltage to settle or series of
NOCs be configured before the next command is sent. But drivers using
this feature have never cared about the serialization aspect. By not
enforcing the serialization we can allow the hardware to run in parallel
improving the performance.

Let's clarify the usage of this member in the tcs_cmd structure to mean
only completion and not serialization. This should also improve the
performance of bus requests where changes could happen in parallel.
Also, CPU resume from deep idle may see benefits from certain wake
requests.

Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Lina Iyer <ilina@codeaurora.org>
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Link: https://lore.kernel.org/r/1610008770-13891-1-git-send-email-mkshah@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
2021-01-07 10:59:46 -06:00
Vineet Gupta f4d9359de8 include/soc: remove headers for EZChip NPS
NPS platform has been removed from ARC port and there are no in-tree
user of it now . So RIP !

Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
2021-01-05 12:59:41 -08:00
Dmitry Osipenko 281462e593 memory: tegra124-emc: Make driver modular
Add modularization support to the Tegra124 EMC driver, which now can be
compiled as a loadable kernel module.

Note that EMC clock must be registered at clk-init time, otherwise PLLM
will be disabled as unused clock at boot time if EMC driver is compiled
as a module. Hence add a prepare/complete callbacks. similarly to what is
done for the Tegra20/30 EMC drivers.

Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20201228154920.18846-2-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
2021-01-05 18:00:09 +01:00
Linus Torvalds 48c1c40ab4 ARM: SoC drivers for v5.11
There are a couple of subsystems maintained by other people that
 merge their drivers through the SoC tree, those changes include:
 
  - The SCMI firmware framework gains support for sensor notifications
    and for controlling voltage domains.
 
  - A large update for the Tegra memory controller driver, integrating
    it better with the interconnect framework
 
  - The memory controller subsystem gains support for Mediatek MT8192
 
  - The reset controller framework gains support for sharing pulsed
    resets
 
 For Soc specific drivers in drivers/soc, the main changes are
 
  - The Allwinner/sunxi MBUS gets a rework for the way it handles
    dma_map_ops and offsets between physical and dma address spaces.
 
  - An errata fix plus some cleanups for Freescale Layerscape SoCs
 
  - A cleanup for renesas drivers regarding MMIO accesses.
 
  - New SoC specific drivers for Mediatek MT8192 and MT8183 power domains
 
  - New SoC specific drivers for Aspeed AST2600 LPC bus control
    and SoC identification.
 
  - Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660
    and SDX55.
 
  - A rework of the TI AM33xx 'genpd' power domain support to use
    information from DT instead of platform data
 
  - Support for TI AM64x SoCs
 
  - Allow building some Amlogic drivers as modules instead of built-in
 
 Finally, there are numerous cleanups and smaller bug fixes for
 Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
 Renesas, and Xilinx SoCs.
 
 There is a trivial conflict in the cedrus driver, with two branches
 adding the same CEDRUS_CAPABILITY_H265_DEC flag, and another trivial
 remove/remove conflict in linux/dma-mapping.h.
 
 Signed-off-by: Arnd Bergmann <arnd@arndb.de>
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAl/alSUACgkQmmx57+YA
 GNm7GRAAlNMVi7F0f4Ixf1bEh+J2QUonYIpZfrdxOLFwISGQ+nstGrFW2He/OeQv
 KAi027tZLl6Sdzjy809cLDPA4Z2IKwjVWhEbBHybvy1+irPYjnixtLd0x3YvPhjH
 iadlcjQ3uaGue8PvubK6CVnBEy82A+Pp29n9i4A4wX/8w+BVIhVsxwQWUBF8pFXE
 3La2UZYZMVMvVZMrpTOqwCgdmLDCk+RLMVZ1IiRqBEBq5/DVq03uIXgjGEOrq8tl
 PXC89w7K510Is891mbBdBThQf+pZkU1vwORuknDcEJKWs9ngbEha7ebVgp32kbFl
 pi8DEK205d106WQgfn0Zxkpbsp8XD058wDILwkhBcteXlBaUEL6btGVLDTUCJZuv
 /pkH8tL4lNGpThQFbCEXC8oHZBp2xk55P+SW9RRZOoA5tAp+sz7hlf3y3YKdCSxv
 4xybeeVOAgjl01WtbEC7CuIkqcKVSQ7njhLhC8r5ASteNywDThqxLT6nd0VegcQc
 YH3Eu9QRXpvFwQ35zMkTMWa27bMG5d60fp90bWT0R5amXZpxJJot87w8trFCxv74
 mE5KvCbefCRNsTt8GOBA/WR7hVaG369g07qOvs7g4LjJEM3Nl2h/A4/zVFef9O0t
 yq3Nm4YCGfDSAQXzGR2SJ3nxiqbDknzJTAtZPf4BmbaMuPOIJ5k=
 =BjJf
 -----END PGP SIGNATURE-----

Merge tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC driver updates from Arnd Bergmann:
 "There are a couple of subsystems maintained by other people that merge
  their drivers through the SoC tree, those changes include:

   - The SCMI firmware framework gains support for sensor notifications
     and for controlling voltage domains.

   - A large update for the Tegra memory controller driver, integrating
     it better with the interconnect framework

   - The memory controller subsystem gains support for Mediatek MT8192

   - The reset controller framework gains support for sharing pulsed
     resets

  For Soc specific drivers in drivers/soc, the main changes are

   - The Allwinner/sunxi MBUS gets a rework for the way it handles
     dma_map_ops and offsets between physical and dma address spaces.

   - An errata fix plus some cleanups for Freescale Layerscape SoCs

   - A cleanup for renesas drivers regarding MMIO accesses.

   - New SoC specific drivers for Mediatek MT8192 and MT8183 power
     domains

   - New SoC specific drivers for Aspeed AST2600 LPC bus control and SoC
     identification.

   - Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660 and
     SDX55.

   - A rework of the TI AM33xx 'genpd' power domain support to use
     information from DT instead of platform data

   - Support for TI AM64x SoCs

   - Allow building some Amlogic drivers as modules instead of built-in

  Finally, there are numerous cleanups and smaller bug fixes for
  Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
  Renesas, and Xilinx SoCs"

* tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (222 commits)
  soc: mediatek: mmsys: Specify HAS_IOMEM dependency for MTK_MMSYS
  firmware: xilinx: Properly align function parameter
  firmware: xilinx: Add a blank line after function declaration
  firmware: xilinx: Remove additional newline
  firmware: xilinx: Fix kernel-doc warnings
  firmware: xlnx-zynqmp: fix compilation warning
  soc: xilinx: vcu: add missing register NUM_CORE
  soc: xilinx: vcu: use vcu-settings syscon registers
  dt-bindings: soc: xlnx: extract xlnx, vcu-settings to separate binding
  soc: xilinx: vcu: drop useless success message
  clk: samsung: mark PM functions as __maybe_unused
  soc: samsung: exynos-chipid: initialize later - with arch_initcall
  soc: samsung: exynos-chipid: order list of SoCs by name
  memory: jz4780_nemc: Fix potential NULL dereference in jz4780_nemc_probe()
  memory: ti-emif-sram: only build for ARMv7
  memory: tegra30: Support interconnect framework
  memory: tegra20: Support hardware versioning and clean up OPP table initialization
  dt-bindings: memory: tegra20-emc: Document opp-supported-hw property
  soc: rockchip: io-domain: Fix error return code in rockchip_iodomain_probe()
  reset-controller: ti: force the write operation when assert or deassert
  ...
2020-12-16 16:38:41 -08:00
Linus Torvalds b4ec805464 Power management updates for 5.11-rc1
- Use local_clock() instead of jiffies in the cpufreq statistics to
    improve accuracy (Viresh Kumar).
 
  - Fix up OPP usage in the cpufreq-dt and qcom-cpufreq-nvmem cpufreq
    drivers (Viresh Kumar).
 
  - Clean up the cpufreq core, the intel_pstate driver and the
    schedutil cpufreq governor (Rafael Wysocki).
 
  - Fix up error code paths in the sti-cpufreq and mediatek cpufreq
    drivers (Yangtao Li, Qinglang Miao).
 
  - Fix cpufreq_online() to return error codes instead of success (0)
    in all cases when it fails (Wang ShaoBo).
 
  - Add mt8167 support to the mediatek cpufreq driver and blacklist
    mt8516 in the cpufreq-dt-platdev driver (Fabien Parent).
 
  - Modify the tegra194 cpufreq driver to always return values from
    the frequency table as the current frequency and clean up that
    driver (Sumit Gupta, Jon Hunter).
 
  - Modify the arm_scmi cpufreq driver to allow it to discover the
    power scale present in the performance protocol and provide this
    information to the Energy Model (Lukasz Luba).
 
  - Add missing MODULE_DEVICE_TABLE to several cpufreq drivers (Pali
    Rohár).
 
  - Clean up the CPPC cpufreq driver (Ionela Voinescu).
 
  - Fix NVMEM_IMX_OCOTP dependency in the imx cpufreq driver (Arnd
    Bergmann).
 
  - Rework the poling interval selection for the polling state in
    cpuidle (Mel Gorman).
 
  - Enable suspend-to-idle for PSCI OSI mode in the PSCI cpuidle
    driver (Ulf Hansson).
 
  - Modify the OPP framework to support empty (node-less) OPP tables
    in DT for passing dependency information (Nicola Mazzucato).
 
  - Fix potential lockdep issue in the OPP core and clean up the OPP
    core (Viresh Kumar).
 
  - Modify dev_pm_opp_put_regulators() to accept a NULL argument and
    update its users accordingly (Viresh Kumar).
 
  - Add frequency changes tracepoint to devfreq (Matthias Kaehlcke).
 
  - Add support for governor feature flags to devfreq, make devfreq
    sysfs file permissions depend on the governor and clean up the
    devfreq core (Chanwoo Choi).
 
  - Clean up the tegra20 devfreq driver and deprecate it to allow
    another driver based on EMC_STAT to be used instead of it (Dmitry
    Osipenko).
 
  - Add interconnect support to the tegra30 devfreq driver, allow it
    to take the interconnect and OPP information from DT and clean it
    up ((Dmitry Osipenko).
 
  - Add interconnect support to the exynos-bus devfreq driver along
    with interconnect properties documentation (Sylwester Nawrocki).
 
  - Add suport for AMD Fam17h and Fam19h processors to the RAPL power
    capping driver (Victor Ding, Kim Phillips).
 
  - Fix handling of overly long constraint names in the powercap
    framework (Lukasz Luba).
 
  - Fix the wakeup configuration handling for bridges in the ACPI
    device power management core (Rafael Wysocki).
 
  - Add support for using an abstract scale for power units in the
    Energy Model (EM) and document it (Lukasz Luba).
 
  - Add em_cpu_energy() micro-optimization to the EM (Pavankumar
    Kondeti).
 
  - Modify the generic power domains (genpd) framwework to support
    suspend-to-idle (Ulf Hansson).
 
  - Fix creation of debugfs nodes in genpd (Thierry Strudel).
 
  - Clean up genpd (Lina Iyer).
 
  - Clean up the core system-wide suspend code and make it print
    driver flags for devices with debug enabled (Alex Shi, Patrice
    Chotard, Chen Yu).
 
  - Modify the ACPI system reboot code to make it prepare for system
    power off to avoid confusing the platform firmware (Kai-Heng Feng).
 
  - Update the pm-graph (multiple changes, mostly usability-related)
    and cpupower (online and offline CPU information support) PM
    utilities (Todd Brandt, Brahadambal Srinivasan).
 -----BEGIN PGP SIGNATURE-----
 
 iQJGBAABCAAwFiEE4fcc61cGeeHD/fCwgsRv/nhiVHEFAl/Y8mcSHHJqd0Byand5
 c29ja2kubmV0AAoJEILEb/54YlRxjY4QAKsNFJeEtjGCxq7MxQIML3QLAsdJM9of
 9kkY9skMEw4v1TRmyy7sW9jZW2pLSRcLJwWRKWu4143qUS3YUp2DQ0lqX4WyXoWu
 BhnkhkMUl6iCeBO8CWnt8zsTuqSa20A13sL9LyqN1+7OZKHD8StbT4hKjBncdNNN
 4aDj+1uAPyOgj2iCUZuHQ8DtpBvOLjgTh367vbhbufjeJ//8/9+R7s4Xzrj7wtmv
 JlE0LDgvge9QeGTpjhxQJzn0q2/H5fg9jbmjPXUfbHJNuyKhrqnmjGyrN5m256JI
 8DqGqQtJpmFp7Ihrur3uKTk3gWO05YwJ1FdeEooAKEjEMObm5xuYhKVRoDhmlJAu
 G6ui+OAUvNR0FffJtbzvWe/pLovLGOEOHdvTrZxUF8Abo6br3untTm8rKTi1fhaF
 wWndSMw0apGsPzCx5T+bE7AbJz2QHFpLhaVAutenuCzNI8xoMlxNKEzsaVz/+FqL
 Pq/PdFaM4vNlMbv7hkb/fujkCs/v3EcX2ihzvt7I2o8dBS0D1X8A4mnuWJmiGslw
 1ftbJ6M9XacwkPBTHPgeXxJh2C1yxxe5VQ9Z5fWWi7sPOUeJnUwxKaluv+coFndQ
 sO6JxsPQ4hQihg8yOxLEkL6Wn68sZlmp+u2Oj+TPFAsAGANIA8rJlBPo1ppJWvdQ
 j1OCIc/qzwpH
 =BVdX
 -----END PGP SIGNATURE-----

Merge tag 'pm-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm

Pull power management updates from Rafael Wysocki:
 "These update cpufreq (core and drivers), cpuidle (polling state
  implementation and the PSCI driver), the OPP (operating performance
  points) framework, devfreq (core and drivers), the power capping RAPL
  (Running Average Power Limit) driver, the Energy Model support, the
  generic power domains (genpd) framework, the ACPI device power
  management, the core system-wide suspend code and power management
  utilities.

  Specifics:

   - Use local_clock() instead of jiffies in the cpufreq statistics to
     improve accuracy (Viresh Kumar).

   - Fix up OPP usage in the cpufreq-dt and qcom-cpufreq-nvmem cpufreq
     drivers (Viresh Kumar).

   - Clean up the cpufreq core, the intel_pstate driver and the
     schedutil cpufreq governor (Rafael Wysocki).

   - Fix up error code paths in the sti-cpufreq and mediatek cpufreq
     drivers (Yangtao Li, Qinglang Miao).

   - Fix cpufreq_online() to return error codes instead of success (0)
     in all cases when it fails (Wang ShaoBo).

   - Add mt8167 support to the mediatek cpufreq driver and blacklist
     mt8516 in the cpufreq-dt-platdev driver (Fabien Parent).

   - Modify the tegra194 cpufreq driver to always return values from the
     frequency table as the current frequency and clean up that driver
     (Sumit Gupta, Jon Hunter).

   - Modify the arm_scmi cpufreq driver to allow it to discover the
     power scale present in the performance protocol and provide this
     information to the Energy Model (Lukasz Luba).

   - Add missing MODULE_DEVICE_TABLE to several cpufreq drivers (Pali
     Rohár).

   - Clean up the CPPC cpufreq driver (Ionela Voinescu).

   - Fix NVMEM_IMX_OCOTP dependency in the imx cpufreq driver (Arnd
     Bergmann).

   - Rework the poling interval selection for the polling state in
     cpuidle (Mel Gorman).

   - Enable suspend-to-idle for PSCI OSI mode in the PSCI cpuidle driver
     (Ulf Hansson).

   - Modify the OPP framework to support empty (node-less) OPP tables in
     DT for passing dependency information (Nicola Mazzucato).

   - Fix potential lockdep issue in the OPP core and clean up the OPP
     core (Viresh Kumar).

   - Modify dev_pm_opp_put_regulators() to accept a NULL argument and
     update its users accordingly (Viresh Kumar).

   - Add frequency changes tracepoint to devfreq (Matthias Kaehlcke).

   - Add support for governor feature flags to devfreq, make devfreq
     sysfs file permissions depend on the governor and clean up the
     devfreq core (Chanwoo Choi).

   - Clean up the tegra20 devfreq driver and deprecate it to allow
     another driver based on EMC_STAT to be used instead of it (Dmitry
     Osipenko).

   - Add interconnect support to the tegra30 devfreq driver, allow it to
     take the interconnect and OPP information from DT and clean it up
     (Dmitry Osipenko).

   - Add interconnect support to the exynos-bus devfreq driver along
     with interconnect properties documentation (Sylwester Nawrocki).

   - Add suport for AMD Fam17h and Fam19h processors to the RAPL power
     capping driver (Victor Ding, Kim Phillips).

   - Fix handling of overly long constraint names in the powercap
     framework (Lukasz Luba).

   - Fix the wakeup configuration handling for bridges in the ACPI
     device power management core (Rafael Wysocki).

   - Add support for using an abstract scale for power units in the
     Energy Model (EM) and document it (Lukasz Luba).

   - Add em_cpu_energy() micro-optimization to the EM (Pavankumar
     Kondeti).

   - Modify the generic power domains (genpd) framwework to support
     suspend-to-idle (Ulf Hansson).

   - Fix creation of debugfs nodes in genpd (Thierry Strudel).

   - Clean up genpd (Lina Iyer).

   - Clean up the core system-wide suspend code and make it print driver
     flags for devices with debug enabled (Alex Shi, Patrice Chotard,
     Chen Yu).

   - Modify the ACPI system reboot code to make it prepare for system
     power off to avoid confusing the platform firmware (Kai-Heng Feng).

   - Update the pm-graph (multiple changes, mostly usability-related)
     and cpupower (online and offline CPU information support) PM
     utilities (Todd Brandt, Brahadambal Srinivasan)"

* tag 'pm-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (86 commits)
  cpufreq: Fix cpufreq_online() return value on errors
  cpufreq: Fix up several kerneldoc comments
  cpufreq: stats: Use local_clock() instead of jiffies
  cpufreq: schedutil: Simplify sugov_update_next_freq()
  cpufreq: intel_pstate: Simplify intel_cpufreq_update_pstate()
  PM: domains: create debugfs nodes when adding power domains
  opp: of: Allow empty opp-table with opp-shared
  dt-bindings: opp: Allow empty OPP tables
  media: venus: dev_pm_opp_put_*() accepts NULL argument
  drm/panfrost: dev_pm_opp_put_*() accepts NULL argument
  drm/lima: dev_pm_opp_put_*() accepts NULL argument
  PM / devfreq: exynos: dev_pm_opp_put_*() accepts NULL argument
  cpufreq: qcom-cpufreq-nvmem: dev_pm_opp_put_*() accepts NULL argument
  cpufreq: dt: dev_pm_opp_put_regulators() accepts NULL argument
  opp: Allow dev_pm_opp_put_*() APIs to accept NULL opp_table
  opp: Don't create an OPP table from dev_pm_opp_get_opp_table()
  cpufreq: dt: Don't (ab)use dev_pm_opp_get_opp_table() to create OPP table
  opp: Reduce the size of critical section in _opp_kref_release()
  PM / EM: Micro optimization in em_cpu_energy
  cpufreq: arm_scmi: Discover the power scale in performance protocol
  ...
2020-12-15 16:30:31 -08:00
Vladimir Oltean ca0b272b48 net: mscc: ocelot: install MAC addresses in .ndo_set_rx_mode from process context
Currently ocelot_set_rx_mode calls ocelot_mact_learn directly, which has
a very nice ocelot_mact_wait_for_completion at the end. Introduced in
commit 639c1b2625 ("net: mscc: ocelot: Register poll timeout should be
wall time not attempts"), this function uses readx_poll_timeout which
triggers a lot of lockdep warnings and is also dangerous to use from
atomic context, potentially leading to lockups and panics.

Steen Hegelund added a poll timeout of 100 ms for checking the MAC
table, a duration which is clearly absurd to poll in atomic context.
So we need to defer the MAC table access to process context, which we do
via a dynamically allocated workqueue which contains all there is to
know about the MAC table operation it has to do.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201212191612.222019-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-12-14 19:28:22 -08:00
Jakub Kicinski 46d5e62dd3 Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
xdp_return_frame_bulk() needs to pass a xdp_buff
to __xdp_return().

strlcpy got converted to strscpy but here it makes no
functional difference, so just keep the right code.

Conflicts:
	net/netfilter/nf_tables_api.c

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-12-11 22:29:38 -08:00
Vladimir Oltean edd2410b16 net: mscc: ocelot: fix dropping of unknown IPv4 multicast on Seville
The current assumption is that the felix DSA driver has flooding knobs
per traffic class, while ocelot switchdev has a single flooding knob.
This was correct for felix VSC9959 and ocelot VSC7514, but with the
introduction of seville VSC9953, we see a switch driven by felix.c which
has a single flooding knob.

So it is clear that we must do what should have been done from the
beginning, which is not to overwrite the configuration done by ocelot.c
in felix, but instead to teach the common ocelot library about the
differences in our switches, and set up the flooding PGIDs centrally.

The effect that the bogus iteration through FELIX_NUM_TC has upon
seville is quite dramatic. ANA_FLOODING is located at 0x00b548, and
ANA_FLOODING_IPMC is located at 0x00b54c. So the bogus iteration will
actually overwrite ANA_FLOODING_IPMC when attempting to write
ANA_FLOODING[1]. There is no ANA_FLOODING[1] in sevile, just ANA_FLOODING.

And when ANA_FLOODING_IPMC is overwritten with a bogus value, the effect
is that ANA_FLOODING_IPMC gets the value of 0x0003CF7D:
	MC6_DATA = 61,
	MC6_CTRL = 61,
	MC4_DATA = 60,
	MC4_CTRL = 0.
Because MC4_CTRL is zero, this means that IPv4 multicast control packets
are not flooded, but dropped. An invalid configuration, and this is how
the issue was actually spotted.

Reported-by: Eldar Gasanov <eldargasanov2@gmail.com>
Reported-by: Maxim Kochetkov <fido_max@inbox.ru>
Tested-by: Eldar Gasanov <eldargasanov2@gmail.com>
Fixes: 84705fc165 ("net: dsa: felix: introduce support for Seville VSC9953 switch")
Fixes: 3c7b51bd39 ("net: dsa: felix: allow flooding for all traffic classes")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201204175416.1445937-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-12-05 15:41:34 -08:00
Dmitry Osipenko 3a0b6b5abf memory: tegra: Correct stub of devm_tegra_memory_controller_get()
Correct typo in a stub of devm_tegra_memory_controller_get() to fix a
non-ARM kernel compile-testing.

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20201111011456.7875-2-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
2020-11-26 18:50:36 +01:00
Dmitry Osipenko 06f079816d memory: tegra-mc: Add interconnect framework
Add common SoC-agnostic ICC framework which turns Tegra Memory Controller
into a memory interconnection provider. This allows us to use interconnect
API for tuning of memory configurations.

Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Link: https://lore.kernel.org/r/20201104164923.21238-33-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
2020-11-26 18:50:35 +01:00
Dmitry Osipenko 6c6bd2075f memory: tegra: Add and use devm_tegra_memory_controller_get()
Multiple Tegra drivers need to retrieve Memory Controller and there is
duplication of the retrieval code among the drivers.

Add new devm_tegra_memory_controller_get() helper to remove the code's
duplication and to fix put_device() which was missed in the duplicated
code. Make EMC drivers to use the new helper.

Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20201104164923.21238-29-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
2020-11-26 18:50:29 +01:00
Dmitry Osipenko 245157a31e soc/tegra: fuse: Add stub for tegra_sku_info
Drivers that use tegra_sku_info and have COMPILE_TEST are failing to be
build due to the missing stub for tegra_sku_info.

Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20201104164923.21238-4-digetx@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
2020-11-06 19:25:21 +01:00
Sebastian Andrzej Siewior f84754dbc5 soc/fsl/qbman: Add an argument to signal if NAPI processing is required.
dpaa_eth_napi_schedule() and caam_qi_napi_schedule() schedule NAPI if
invoked from:

 - Hard interrupt context
 - Any context which is not serving soft interrupts

Any context which is not serving soft interrupts includes hard interrupts
so the in_irq() check is redundant. caam_qi_napi_schedule() has a comment
about this:

        /*
         * In case of threaded ISR, for RT kernels in_irq() does not return
         * appropriate value, so use in_serving_softirq to distinguish between
         * softirq and irq contexts.
         */
         if (in_irq() || !in_serving_softirq())

This has nothing to do with RT. Even on a non RT kernel force threaded
interrupts run obviously in thread context and therefore in_irq() returns
false when invoked from the handler.

The extension of the in_irq() check with !in_serving_softirq() was there
when the drivers were added, but in the out of tree FSL BSP the original
condition was in_irq() which got extended due to failures on RT.

The usage of in_xxx() in drivers is phased out and Linus clearly requested
that code which changes behaviour depending on context should either be
separated or the context be conveyed in an argument passed by the caller,
which usually knows the context. Right he is, the above construct is
clearly showing why.

The following callchains have been analyzed to end up in
dpaa_eth_napi_schedule():

qman_p_poll_dqrr()
  __poll_portal_fast()
    fq->cb.dqrr()
       dpaa_eth_napi_schedule()

portal_isr()
  __poll_portal_fast()
    fq->cb.dqrr()
       dpaa_eth_napi_schedule()

Both need to schedule NAPI.
The crypto part has another code path leading up to this:
  kill_fq()
     empty_retired_fq()
       qman_p_poll_dqrr()
         __poll_portal_fast()
            fq->cb.dqrr()
               dpaa_eth_napi_schedule()

kill_fq() is called from task context and ends up scheduling NAPI, but
that's pointless and an unintended side effect of the !in_serving_softirq()
check.

The code path:
  caam_qi_poll() -> qman_p_poll_dqrr()

is invoked from NAPI and I *assume* from crypto's NAPI device and not
from qbman's NAPI device. I *guess* it is okay to skip scheduling NAPI
(because this is what happens now) but could be changed if it is wrong
due to `budget' handling.

Add an argument to __poll_portal_fast() which is true if NAPI needs to be
scheduled. This requires propagating the value to the caller including
`qman_cb_dqrr' typedef which is used by the dpaa and the crypto driver.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Aymen Sghaier <aymen.sghaier@nxp.com>
Cc: Herbert XS <herbert@gondor.apana.org.au>
Cc: Li Yang <leoyang.li@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Tested-by: Camelia Groza <camelia.groza@nxp.com>
2020-11-03 17:41:03 -08:00
Vladimir Oltean 2f0402fedf net: mscc: ocelot: deny changing the native VLAN from the prepare phase
Put the preparation phase of switchdev VLAN objects to some good use,
and move the check we already had, for preventing the existence of more
than one egress-untagged VLAN per port, to the preparation phase of the
addition.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-11-02 17:09:07 -08:00
Vladimir Oltean e2b2e83e52 net: mscc: ocelot: add a "valid" boolean to struct ocelot_vlan
Currently we are checking in some places whether the port has a native
VLAN on egress or not, by comparing the ocelot_port->vid value with zero.

That works, because VID 0 can never be a native VLAN configured by the
bridge, but now we want to make similar checks for the pvid. That won't
work, because there are cases when we do have the pvid set to 0 (not by
the bridge, by ourselves, but still.. it's confusing). And we can't
encode a negative value into an u16, so add a bool to the structure.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-11-02 17:09:06 -08:00
Vladimir Oltean c3e58a750e net: mscc: ocelot: transform the pvid and native vlan values into a structure
This is a mechanical patch only.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-11-02 17:09:06 -08:00
Vladimir Oltean e5d1f896fd net: mscc: ocelot: support L2 multicast entries
There is one main difference in mscc_ocelot between IP multicast and L2
multicast. With IP multicast, destination ports are encoded into the
upper bytes of the multicast MAC address. Example: to deliver the
address 01:00:5E:11:22:33 to ports 3, 8, and 9, one would need to
program the address of 00:03:08:11:22:33 into hardware. Whereas for L2
multicast, the MAC table entry points to a Port Group ID (PGID), and
that PGID contains the port mask that the packet will be forwarded to.
As to why it is this way, no clue. My guess is that not all port
combinations can be supported simultaneously with the limited number of
PGIDs, and this was somehow an issue for IP multicast but not for L2
multicast. Anyway.

Prior to this change, the raw L2 multicast code was bogus, due to the
fact that there wasn't really any way to test it using the bridge code.
There were 2 issues:
- A multicast PGID was allocated for each MDB entry, but it wasn't in
  fact programmed to hardware. It was dummy.
- In fact we don't want to reserve a multicast PGID for every single MDB
  entry. That would be odd because we can only have ~60 PGIDs, but
  thousands of MDB entries. So instead, we want to reserve a multicast
  PGID for every single port combination for multicast traffic. And
  since we can have 2 (or more) MDB entries delivered to the same port
  group (and therefore PGID), we need to reference-count the PGIDs.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-10-30 18:25:56 -07:00
Linus Torvalds 2e368dd2bb ARM: SoC-related driver updates
Various driver updates for platforms. A bulk of this is smaller fixes or
 cleanups, but some of the new material this time around is:
 
  - Support for Nvidia Tegra234 SoC
  - Ring accelerator support for TI AM65x
  - PRUSS driver for TI platforms
  - Renesas support for R-Car V3U SoC
  - Reset support for Cortex-M4 processor on i.MX8MQ
 
 There are also new socinfo entries for a handful of different SoCs
 and platforms.
 -----BEGIN PGP SIGNATURE-----
 
 iQJDBAABCgAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAl+TUboPHG9sb2ZAbGl4
 b20ubmV0AAoJEIwa5zzehBx3T4YP/R5pjF2C1gt8FrCaG4IfhIY1VHWelfPcB5qB
 RC7Pn4MCRCEY+10YPXA70oS6KBaC+gtZ4bPeInzfLXh1ynFJJb+XtAIxoRhnkEw+
 /R979wNcIls9JqkvnHWFx29Y008W2ZNcXVNKH7O2Gxy+eKzDcTMsoH/zj8xWrV5b
 +eBllTzGU4RArYRJdcwOBQwMO6L2pzADHZ7hGMAY//8fo+qrxg8b9EINsH1UHCa8
 gQdWdVlmv6GeLB6RYLRBCWxpW4jOLDqEAvyDV84QQmYHvzD9tqJExNR0hfGTs4TU
 TZWK7LWSNqF0ujQUbFh9Ikcx6DypU1gvE7LKhCDrf4D7HLRX5v4BjGH+xtVtjsyD
 xzh4WEoa3qCNu1mxQjKG8Y6U7bB9cRI2TPVxbbmI4ZuF0njvybecwwOZUBQl4aD4
 5x+Df3pO/E5ECLOBeTnLgvw20fcjHv4HP8l63B6ADb31FUiZrJXItvayY5qXWe+P
 HSgUykmVA4nd4PnLsSj9seyWqOTIqUZ3U3TsmfxIQh2Otie01okwuHb1J7ErO/u0
 W148SgSwVbnkPxjbBHKGgC2r+Q/AjSDGRBYL0ThIVFUztxTBBwhj3FIvMnyyxTIj
 yFBY14KQ8FcNUs8DrbPCaAx/RDCB02IHdvvIlyTmU3RBq7UhJVIglpLzzo2ed9F2
 5u/aVH3y
 =tfPb
 -----END PGP SIGNATURE-----

Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC-related driver updates from Olof Johansson:
 "Various driver updates for platforms. A bulk of this is smaller fixes
  or cleanups, but some of the new material this time around is:

   - Support for Nvidia Tegra234 SoC

   - Ring accelerator support for TI AM65x

   - PRUSS driver for TI platforms

   - Renesas support for R-Car V3U SoC

   - Reset support for Cortex-M4 processor on i.MX8MQ

  There are also new socinfo entries for a handful of different SoCs and
  platforms"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (131 commits)
  drm/mediatek: reduce clear event
  soc: mediatek: cmdq: add clear option in cmdq_pkt_wfe api
  soc: mediatek: cmdq: add jump function
  soc: mediatek: cmdq: add write_s_mask value function
  soc: mediatek: cmdq: add write_s value function
  soc: mediatek: cmdq: add read_s function
  soc: mediatek: cmdq: add write_s_mask function
  soc: mediatek: cmdq: add write_s function
  soc: mediatek: cmdq: add address shift in jump
  soc: mediatek: mtk-infracfg: Fix kerneldoc
  soc: amlogic: pm-domains: use always-on flag
  reset: sti: reset-syscfg: fix struct description warnings
  reset: imx7: add the cm4 reset for i.MX8MQ
  dt-bindings: reset: imx8mq: add m4 reset
  reset: Fix and extend kerneldoc
  reset: reset-zynqmp: Added support for Versal platform
  dt-bindings: reset: Updated binding for Versal reset driver
  reset: imx7: Support module build
  soc: fsl: qe: Remove unnessesary check in ucc_set_tdm_rxtx_clk
  soc: fsl: qman: convert to use be32_add_cpu()
  ...
2020-10-24 10:39:22 -07:00
Linus Torvalds 9ff9b0d392 networking changes for the 5.10 merge window
Add redirect_neigh() BPF packet redirect helper, allowing to limit stack
 traversal in common container configs and improving TCP back-pressure.
 Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain.
 
 Expand netlink policy support and improve policy export to user space.
 (Ge)netlink core performs request validation according to declared
 policies. Expand the expressiveness of those policies (min/max length
 and bitmasks). Allow dumping policies for particular commands.
 This is used for feature discovery by user space (instead of kernel
 version parsing or trial and error).
 
 Support IGMPv3/MLDv2 multicast listener discovery protocols in bridge.
 
 Allow more than 255 IPv4 multicast interfaces.
 
 Add support for Type of Service (ToS) reflection in SYN/SYN-ACK
 packets of TCPv6.
 
 In Multi-patch TCP (MPTCP) support concurrent transmission of data
 on multiple subflows in a load balancing scenario. Enhance advertising
 addresses via the RM_ADDR/ADD_ADDR options.
 
 Support SMC-Dv2 version of SMC, which enables multi-subnet deployments.
 
 Allow more calls to same peer in RxRPC.
 
 Support two new Controller Area Network (CAN) protocols -
 CAN-FD and ISO 15765-2:2016.
 
 Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit
 kernel problem.
 
 Add TC actions for implementing MPLS L2 VPNs.
 
 Improve nexthop code - e.g. handle various corner cases when nexthop
 objects are removed from groups better, skip unnecessary notifications
 and make it easier to offload nexthops into HW by converting
 to a blocking notifier.
 
 Support adding and consuming TCP header options by BPF programs,
 opening the doors for easy experimental and deployment-specific
 TCP option use.
 
 Reorganize TCP congestion control (CC) initialization to simplify life
 of TCP CC implemented in BPF.
 
 Add support for shipping BPF programs with the kernel and loading them
 early on boot via the User Mode Driver mechanism, hence reusing all the
 user space infra we have.
 
 Support sleepable BPF programs, initially targeting LSM and tracing.
 
 Add bpf_d_path() helper for returning full path for given 'struct path'.
 
 Make bpf_tail_call compatible with bpf-to-bpf calls.
 
 Allow BPF programs to call map_update_elem on sockmaps.
 
 Add BPF Type Format (BTF) support for type and enum discovery, as
 well as support for using BTF within the kernel itself (current use
 is for pretty printing structures).
 
 Support listing and getting information about bpf_links via the bpf
 syscall.
 
 Enhance kernel interfaces around NIC firmware update. Allow specifying
 overwrite mask to control if settings etc. are reset during update;
 report expected max time operation may take to users; support firmware
 activation without machine reboot incl. limits of how much impact
 reset may have (e.g. dropping link or not).
 
 Extend ethtool configuration interface to report IEEE-standard
 counters, to limit the need for per-vendor logic in user space.
 
 Adopt or extend devlink use for debug, monitoring, fw update
 in many drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw,
 mv88e6xxx, dpaa2-eth).
 
 In mlxsw expose critical and emergency SFP module temperature alarms.
 Refactor port buffer handling to make the defaults more suitable and
 support setting these values explicitly via the DCBNL interface.
 
 Add XDP support for Intel's igb driver.
 
 Support offloading TC flower classification and filtering rules to
 mscc_ocelot switches.
 
 Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as
 fixed interval period pulse generator and one-step timestamping in
 dpaa-eth.
 
 Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3)
 offload.
 
 Add Lynx PHY/PCS MDIO module, and convert various drivers which have
 this HW to use it. Convert mvpp2 to split PCS.
 
 Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as
 7-port Mediatek MT7531 IP.
 
 Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver,
 and wcn3680 support in wcn36xx.
 
 Improve performance for packets which don't require much offloads
 on recent Mellanox NICs by 20% by making multiple packets share
 a descriptor entry.
 
 Move chelsio inline crypto drivers (for TLS and IPsec) from the crypto
 subtree to drivers/net. Move MDIO drivers out of the phy directory.
 
 Clean up a lot of W=1 warnings, reportedly the actively developed
 subsections of networking drivers should now build W=1 warning free.
 
 Make sure drivers don't use in_interrupt() to dynamically adapt their
 code. Convert tasklets to use new tasklet_setup API (sadly this
 conversion is not yet complete).
 
 Signed-off-by: Jakub Kicinski <kuba@kernel.org>
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCAAdFiEE6jPA+I1ugmIBA4hXMUZtbf5SIrsFAl+ItRwACgkQMUZtbf5S
 IrtTMg//UxpdR/MirT1DatBU0K/UGAZY82hV7F/UC8tPgjfHZeHvWlDFxfi3YP81
 PtPKbhRZ7DhwBXefUp6nY3UdvjftrJK2lJm8prJUPSsZRye8Wlcb7y65q7/P2y2U
 Efucyopg6RUrmrM0DUsIGYGJgylQLHnMYUl/keCsD4t5Bp4ksyi9R2t5eitGoWzh
 r3QGdbSa0AuWx4iu0i+tqp6Tj0ekMBMXLVb35dtU1t0joj2KTNEnSgABN3prOa8E
 iWYf2erOau68Ogp3yU3miCy0ZU4p/7qGHTtzbcp677692P/ekak6+zmfHLT9/Pjy
 2Stq2z6GoKuVxdktr91D9pA3jxG4LxSJmr0TImcGnXbvkMP3Ez3g9RrpV5fn8j6F
 mZCH8TKZAoD5aJrAJAMkhZmLYE1pvDa7KolSk8WogXrbCnTEb5Nv8FHTS1Qnk3yl
 wSKXuvutFVNLMEHCnWQLtODbTST9DI/aOi6EctPpuOA/ZyL1v3pl+gfp37S+LUTe
 owMnT/7TdvKaTD0+gIyU53M6rAWTtr5YyRQorX9awIu/4Ha0F0gYD7BJZQUGtegp
 HzKt59NiSrFdbSH7UdyemdBF4LuCgIhS7rgfeoUXMXmuPHq7eHXyHZt5dzPPa/xP
 81P0MAvdpFVwg8ij2yp2sHS7sISIRKq17fd1tIewUabxQbjXqPc=
 =bc1U
 -----END PGP SIGNATURE-----

Merge tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

Pull networking updates from Jakub Kicinski:

 - Add redirect_neigh() BPF packet redirect helper, allowing to limit
   stack traversal in common container configs and improving TCP
   back-pressure.

   Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain.

 - Expand netlink policy support and improve policy export to user
   space. (Ge)netlink core performs request validation according to
   declared policies. Expand the expressiveness of those policies
   (min/max length and bitmasks). Allow dumping policies for particular
   commands. This is used for feature discovery by user space (instead
   of kernel version parsing or trial and error).

 - Support IGMPv3/MLDv2 multicast listener discovery protocols in
   bridge.

 - Allow more than 255 IPv4 multicast interfaces.

 - Add support for Type of Service (ToS) reflection in SYN/SYN-ACK
   packets of TCPv6.

 - In Multi-patch TCP (MPTCP) support concurrent transmission of data on
   multiple subflows in a load balancing scenario. Enhance advertising
   addresses via the RM_ADDR/ADD_ADDR options.

 - Support SMC-Dv2 version of SMC, which enables multi-subnet
   deployments.

 - Allow more calls to same peer in RxRPC.

 - Support two new Controller Area Network (CAN) protocols - CAN-FD and
   ISO 15765-2:2016.

 - Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit
   kernel problem.

 - Add TC actions for implementing MPLS L2 VPNs.

 - Improve nexthop code - e.g. handle various corner cases when nexthop
   objects are removed from groups better, skip unnecessary
   notifications and make it easier to offload nexthops into HW by
   converting to a blocking notifier.

 - Support adding and consuming TCP header options by BPF programs,
   opening the doors for easy experimental and deployment-specific TCP
   option use.

 - Reorganize TCP congestion control (CC) initialization to simplify
   life of TCP CC implemented in BPF.

 - Add support for shipping BPF programs with the kernel and loading
   them early on boot via the User Mode Driver mechanism, hence reusing
   all the user space infra we have.

 - Support sleepable BPF programs, initially targeting LSM and tracing.

 - Add bpf_d_path() helper for returning full path for given 'struct
   path'.

 - Make bpf_tail_call compatible with bpf-to-bpf calls.

 - Allow BPF programs to call map_update_elem on sockmaps.

 - Add BPF Type Format (BTF) support for type and enum discovery, as
   well as support for using BTF within the kernel itself (current use
   is for pretty printing structures).

 - Support listing and getting information about bpf_links via the bpf
   syscall.

 - Enhance kernel interfaces around NIC firmware update. Allow
   specifying overwrite mask to control if settings etc. are reset
   during update; report expected max time operation may take to users;
   support firmware activation without machine reboot incl. limits of
   how much impact reset may have (e.g. dropping link or not).

 - Extend ethtool configuration interface to report IEEE-standard
   counters, to limit the need for per-vendor logic in user space.

 - Adopt or extend devlink use for debug, monitoring, fw update in many
   drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw, mv88e6xxx,
   dpaa2-eth).

 - In mlxsw expose critical and emergency SFP module temperature alarms.
   Refactor port buffer handling to make the defaults more suitable and
   support setting these values explicitly via the DCBNL interface.

 - Add XDP support for Intel's igb driver.

 - Support offloading TC flower classification and filtering rules to
   mscc_ocelot switches.

 - Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as
   fixed interval period pulse generator and one-step timestamping in
   dpaa-eth.

 - Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3)
   offload.

 - Add Lynx PHY/PCS MDIO module, and convert various drivers which have
   this HW to use it. Convert mvpp2 to split PCS.

 - Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as
   7-port Mediatek MT7531 IP.

 - Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver,
   and wcn3680 support in wcn36xx.

 - Improve performance for packets which don't require much offloads on
   recent Mellanox NICs by 20% by making multiple packets share a
   descriptor entry.

 - Move chelsio inline crypto drivers (for TLS and IPsec) from the
   crypto subtree to drivers/net. Move MDIO drivers out of the phy
   directory.

 - Clean up a lot of W=1 warnings, reportedly the actively developed
   subsections of networking drivers should now build W=1 warning free.

 - Make sure drivers don't use in_interrupt() to dynamically adapt their
   code. Convert tasklets to use new tasklet_setup API (sadly this
   conversion is not yet complete).

* tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2583 commits)
  Revert "bpfilter: Fix build error with CONFIG_BPFILTER_UMH"
  net, sockmap: Don't call bpf_prog_put() on NULL pointer
  bpf, selftest: Fix flaky tcp_hdr_options test when adding addr to lo
  bpf, sockmap: Add locking annotations to iterator
  netfilter: nftables: allow re-computing sctp CRC-32C in 'payload' statements
  net: fix pos incrementment in ipv6_route_seq_next
  net/smc: fix invalid return code in smcd_new_buf_create()
  net/smc: fix valid DMBE buffer sizes
  net/smc: fix use-after-free of delayed events
  bpfilter: Fix build error with CONFIG_BPFILTER_UMH
  cxgb4/ch_ipsec: Replace the module name to ch_ipsec from chcr
  net: sched: Fix suspicious RCU usage while accessing tcf_tunnel_info
  bpf: Fix register equivalence tracking.
  rxrpc: Fix loss of final ack on shutdown
  rxrpc: Fix bundle counting for exclusive connections
  netfilter: restore NF_INET_NUMHOOKS
  ibmveth: Identify ingress large send packets.
  ibmveth: Switch order of ibmveth_helper calls.
  cxgb4: handle 4-tuple PEDIT to NAT mode translation
  selftests: Add VRF route leaking tests
  ...
2020-10-15 18:42:13 -07:00
Linus Torvalds c6dbef7307 USB/PHY/Thunderbolt driver patches for 5.10-rc1
Here is the big set of USB, PHY, and Thunderbolt driver updates for
 5.10-rc1.
 
 Lots of tiny different things for these subsystems are in here,
 including:
 	- phy driver updates
 	- thunderbolt / USB 4 updates and additions
 	- USB gadget driver updates
 	- xhci fixes and updates
 	- typec driver additions and updates
 	- api conversions to various drivers for core kernel api changes
 	- new USB control message functions to make it harder to get
 	  wrong, as found by syzbot (took 2 tries to get it right)
 	- lots of tiny USB driver fixes and updates all over the place
 
 All of these have been in linux-next for a while, with the exception of
 the last "obviously correct" patch that updated a FALLTHROUGH comment
 that got merged last weekend.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX4hAAg8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+ykfRACcCp48StLg4V7XcZ41eQYES/DVwxkAnjnZs+La
 Y7F+o2p8DiuLLQamdEyB
 =lHr1
 -----END PGP SIGNATURE-----

Merge tag 'usb-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB/PHY/Thunderbolt driver updates from Greg KH:
 "Here is the big set of USB, PHY, and Thunderbolt driver updates for
  5.10-rc1.

  Lots of tiny different things for these subsystems are in here,
  including:

   - phy driver updates

   - thunderbolt / USB 4 updates and additions

   - USB gadget driver updates

   - xhci fixes and updates

   - typec driver additions and updates

   - api conversions to various drivers for core kernel api changes

   - new USB control message functions to make it harder to get wrong,
     as found by syzbot (took 2 tries to get it right)

   - lots of tiny USB driver fixes and updates all over the place

  All of these have been in linux-next for a while, with the exception
  of the last "obviously correct" patch that updated a FALLTHROUGH
  comment that got merged last weekend"

* tag 'usb-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (374 commits)
  usb: musb: gadget: Use fallthrough pseudo-keyword
  usb: typec: Add QCOM PMIC typec detection driver
  USB: serial: option: add Cellient MPL200 card
  usb: typec: tcpci_maxim: Add support for Sink FRS
  usb: typec: tcpci: Implement callbacks for FRS
  usb: typec: tcpm: Add support for Sink Fast Role SWAP(FRS)
  usb: typec: tcpci_maxim: Chip level TCPC driver
  usb: typec: tcpci: Add set_vbus tcpci callback
  usb: typec: tcpci: Add a getter method to retrieve tcpm_port reference
  usbip: vhci_hcd: fix calling usb_hcd_giveback_urb() with irqs enabled
  usb: cdc-acm: add quirk to blacklist ETAS ES58X devices
  USB: serial: ftdi_sio: use cur_altsetting for consistency
  USB: serial: option: Add Telit FT980-KS composition
  USB: core: remove polling for /sys/kernel/debug/usb/devices
  usb: typec: add support for STUSB160x Type-C controller family
  usb: typec: add typec_find_pwr_opmode
  usb: typec: hd3ss3220: Use OF graph API to get the connector fwnode
  dt-bindings: usb: renesas,usb3-peri: Document HS and SS data bus
  dt-bindings: usb: convert ti,hd3ss3220 bindings to json-schema
  usb: dwc2: Fix INTR OUT transfers in DDMA mode.
  ...
2020-10-15 09:51:18 -07:00
David S. Miller 8b0308fe31 Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Rejecting non-native endian BTF overlapped with the addition
of support for it.

The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.

Signed-off-by: David S. Miller <davem@davemloft.net>
2020-10-05 18:40:01 -07:00
Vladimir Oltean 2e554a7a5d net: dsa: propagate switchdev vlan_filtering prepare phase to drivers
A driver may refuse to enable VLAN filtering for any reason beyond what
the DSA framework cares about, such as:
- having tc-flower rules that rely on the switch being VLAN-aware
- the particular switch does not support VLAN, even if the driver does
  (the DSA framework just checks for the presence of the .port_vlan_add
  and .port_vlan_del pointers)
- simply not supporting this configuration to be toggled at runtime

Currently, when a driver rejects a configuration it cannot support, it
does this from the commit phase, which triggers various warnings in
switchdev.

So propagate the prepare phase to drivers, to give them the ability to
refuse invalid configurations cleanly and avoid the warnings.

Since we need to modify all function prototypes and check for the
prepare phase from within the drivers, take that opportunity and move
the existing driver restrictions within the prepare phase where that is
possible and easy.

Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Microchip Linux Driver Support <UNGLinuxDriver@microchip.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Landen Chao <Landen.Chao@mediatek.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Jonathan McDowell <noodles@earth.li>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-10-05 05:56:48 -07:00
Greg Kroah-Hartman 168ae5a74b Merge 5.9-rc8 into usb-next
We need the USB fixes in here as well for testing.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-05 08:54:36 +02:00
Olof Johansson c78c6e18ab NXP/FSL SoC driver updates for v5.10
Fix various compile warnings and static analysis warnings for:
 - QBMan driver
 - DPIO driver
 - QE driver
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEhb3UXAyxp6UQ0v6khtxQDvusFVQFAl9rzkAACgkQhtxQDvus
 FVTScw//aSBoWqDqADbph5fR/aEIrycXW38sVqXFuMgnMiSV33rBHVw5LKsTjO10
 olL+sGf+yqPx6lRVHEAVlhcHCsR9szBj7B1aUd9XdT7Dbec8guerNrlfIsoi5t8X
 7i3AKzp5B1WqVa5mXqUhbXx0077MuRnZG4xDAPgRIA7NFCIQma/cJ1QUScZVKRNV
 7vJf9mvkw3xw6aLzIo1zmAJgcEcRFudZFoRfWqW+f4t5SVYepmdBMXOrLeLEf4Lt
 Kv1+RucY8pHrnDM+MdxWObLKJpudPZTNeWJogyDPPnBEaEr/IkjvedjhT06jIumx
 sFLfyP5zlULiYMY+dKw43MDz7sxGxvi4ZDybRW5iU0mVwjFaMVLdN2QyzhJoWppt
 PjcIvn9mmhMC4Hk5e4WzDuHPwFkKRktRtqvTyx3pXPWuZmmsBNNqM96DeOrxt6yN
 IO8sWoH/WKDkP5rU+nGmie0KgGaIp5oDN7ZYjGqUHlQ/6g4xJhd28MwtiUSo8tqW
 2RkgAjuzKlB335AxsWFD3zW4+Qup3yie3Nzl2ysndkXTQZQizjD4yVQCwJUd6udt
 1REPrdKYDs9dokfTNUP7rLUwgE4xgNFgpLCnYuek6IhyBrtUgnh9kPmg2BcGYS9h
 d2BGiGHotxO9i4YqmlDkz4XIweI6h1s8hIHWNj+lV1orLQAiwIk=
 =4+F2
 -----END PGP SIGNATURE-----

Merge tag 'soc-fsl-next-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/drivers

NXP/FSL SoC driver updates for v5.10

Fix various compile warnings and static analysis warnings for:
- QBMan driver
- DPIO driver
- QE driver

* tag 'soc-fsl-next-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
  soc: fsl: qe: Remove unnessesary check in ucc_set_tdm_rxtx_clk
  soc: fsl: qman: convert to use be32_add_cpu()
  soc: fsl: dpio: remove set but not used 'addr_cena'
  soc: fsl: qbman: Fix return value on success
  soc: fsl: qman: fix -Wpacked-not-aligned warnings

Link: https://lore.kernel.org/r/20200923224416.25788-1-leoyang.li@nxp.com
Signed-off-by: Olof Johansson <olof@lixom.net>
2020-10-03 12:59:14 -07:00
Vladimir Oltean 1397a2eb52 net: mscc: ocelot: create TCAM skeleton from tc filter chains
For Ocelot switches, there are 2 ingress pipelines for flow offload
rules: VCAP IS1 (Ingress Classification) and IS2 (Security Enforcement).
IS1 and IS2 support different sets of actions. The pipeline order for a
packet on ingress is:

Basic classification -> VCAP IS1 -> VCAP IS2

Furthermore, IS1 is looked up 3 times, and IS2 is looked up twice (each
TCAM entry can be configured to match only on the first lookup, or only
on the second, or on both etc).

Because the TCAMs are completely independent in hardware, and because of
the fixed pipeline, we actually have very limited options when it comes
to offloading complex rules to them while still maintaining the same
semantics with the software data path.

This patch maps flow offload rules to ingress TCAMs according to a
predefined chain index number. There is going to be a script in
selftests that clarifies the usage model.

There is also an egress TCAM (VCAP ES0, the Egress Rewriter), which is
modeled on top of the default chain 0 of the egress qdisc, because it
doesn't have multiple lookups.

Suggested-by: Allan W. Nielsen <allan.nielsen@microchip.com>
Co-developed-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-10-02 15:40:30 -07:00
Vladimir Oltean 319e4dd11a net: mscc: ocelot: introduce conversion helpers between port and netdev
Since the mscc_ocelot_switch_lib is common between a pure switchdev and
a DSA driver, the procedure of retrieving a net_device for a certain
port index differs, as those are registered by their individual
front-ends.

Up to now that has been dealt with by always passing the port index to
the switch library, but now, we're going to need to work with net_device
pointers from the tc-flower offload, for things like indev, or mirred.
It is not desirable to refactor that, so let's make sure that the flower
offload core has the ability to translate between a net_device and a
port index properly.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-10-02 15:40:30 -07:00
Vladimir Oltean 2096805497 net: mscc: ocelot: automatically detect VCAP constants
The numbers in struct vcap_props are not intuitive to derive, because
they are not a straightforward copy-and-paste from the reference manual
but instead rely on a fairly detailed level of understanding of the
layout of an entry in the TCAM and in the action RAM. For this reason,
bugs are very easy to introduce here.

Ease the work of hardware porters and read from hardware the constants
that were exported for this particular purpose. Note that this implies
that struct vcap_props can no longer be const.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-29 18:26:24 -07:00
Vladimir Oltean e3aea296d8 net: mscc: ocelot: add definitions for VCAP ES0 keys, actions and target
As a preparation step for the offloading to ES0, let's create the
infrastructure for talking with this hardware block.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-29 18:26:12 -07:00
Vladimir Oltean a61e365d7c net: mscc: ocelot: add definitions for VCAP IS1 keys, actions and target
As a preparation step for the offloading to IS1, let's create the
infrastructure for talking with this hardware block.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-29 18:26:12 -07:00
Vladimir Oltean c1c3993edb net: mscc: ocelot: generalize existing code for VCAP
In the Ocelot switches there are 3 TCAMs: VCAP ES0, IS1 and IS2, which
have the same configuration interface, but different sets of keys and
actions. The driver currently only supports VCAP IS2.

In preparation of VCAP IS1 and ES0 support, the existing code must be
generalized to work with any VCAP.

In that direction, we should move the structures that depend upon VCAP
instantiation, like vcap_is2_keys and vcap_is2_actions, out of struct
ocelot and into struct vcap_props .keys and .actions, a structure that
is replicated 3 times, once per VCAP. We'll pass that structure as an
argument to each function that does the key and action packing - only
the control logic needs to distinguish between ocelot->vcap[VCAP_IS2]
or IS1 or ES0.

Another change is to make use of the newly introduced ocelot_target_read
and ocelot_target_write API, since the 3 VCAPs have the same registers
but put at different addresses.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-29 18:26:12 -07:00
Vladimir Oltean 3c0e37a9e4 net: mscc: ocelot: introduce a new ocelot_target_{read,write} API
There are some targets (register blocks) in the Ocelot switch that are
instantiated more than once. For example, the VCAP IS1, IS2 and ES0
blocks all share the same register layout for interacting with the cache
for the TCAM and the action RAM.

For the VCAPs, the procedure for servicing them is actually common. We
just need an API specifying which VCAP we are talking to, and we do that
via these raw ocelot_target_read and ocelot_target_write accessors.

In plain ocelot_read, the target is encoded into the register enum
itself:

	u16 target = reg >> TARGET_OFFSET;

For the VCAPs, the registers are currently defined like this:

	enum ocelot_reg {
	[...]
		S2_CORE_UPDATE_CTRL = S2 << TARGET_OFFSET,
		S2_CORE_MV_CFG,
		S2_CACHE_ENTRY_DAT,
		S2_CACHE_MASK_DAT,
		S2_CACHE_ACTION_DAT,
		S2_CACHE_CNT_DAT,
		S2_CACHE_TG_DAT,
	[...]
	};

which is precisely what we want to avoid, because we'd have to duplicate
the same register map for S1 and for S0, and then figure out how to pass
VCAP instance-specific registers to the ocelot_read calls (basically
another lookup table that undoes the effect of shifting with
TARGET_OFFSET).

So for some targets, propose a more raw API, similar to what is
currently done with ocelot_port_readl and ocelot_port_writel. Those
targets can only be accessed with ocelot_target_{read,write} and not
with ocelot_{read,write} after the conversion, which is fine.

The VCAP registers are not actually modified to use this new API as of
this patch. They will be modified in the next one.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-29 18:26:12 -07:00
Vladimir Oltean 5124197ce5 net: dsa: tag_ocelot: use a short prefix on both ingress and egress
There are 2 goals that we follow:

- Reduce the header size
- Make the header size equal between RX and TX

The issue that required long prefix on RX was the fact that the ocelot
DSA tag, being put before Ethernet as it is, would overlap with the area
that a DSA master uses for RX filtering (destination MAC address
mainly).

Now that we can ask DSA to put the master in promiscuous mode, in theory
we could remove the prefix altogether and call it a day, but it looks
like we can't. Using no prefix on ingress, some packets (such as ICMP)
would be received, while others (such as PTP) would not be received.
This is because the DSA master we use (enetc) triggers parse errors
("MAC rx frame errors") presumably because it sees Ethernet frames with
a bad length. And indeed, when using no prefix, the EtherType (bytes
12-13 of the frame, bits 96-111) falls over the REW_VAL field from the
extraction header, aka the PTP timestamp.

When turning the short (32-bit) prefix on, the EtherType overlaps with
bits 64-79 of the extraction header, which are a reserved area
transmitted as zero by the switch. The packets are not dropped by the
DSA master with a short prefix. Actually, the frames look like this in
tcpdump (below is a PTP frame, with an extra dsa_8021q tag - dadb 0482 -
added by a downstream sja1105).

89:0c:a9:f2:01:00 > 88:80:00:0a:00:1d, 802.3, length 0: LLC, \
	dsap Unknown (0x10) Individual, ssap ProWay NM (0x0e) Response, \
	ctrl 0x0004: Information, send seq 2, rcv seq 0, \
	Flags [Response], length 78

0x0000:  8880 000a 001d 890c a9f2 0100 0000 100f  ................
0x0010:  0400 0000 0180 c200 000e 001f 7b63 0248  ............{c.H
0x0020:  dadb 0482 88f7 1202 0036 0000 0000 0000  .........6......
0x0030:  0000 0000 0000 0000 0000 001f 7bff fe63  ............{..c
0x0040:  0248 0001 1f81 0500 0000 0000 0000 0000  .H..............
0x0050:  0000 0000 0000 0000 0000 0000            ............

So the short prefix is our new default: we've shortened our RX frames by
12 octets, increased TX by 4, and headers are now equal between RX and
TX. Note that we still need promiscuous mode for the DSA master to not
drop it.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-26 14:17:58 -07:00
Vladimir Oltean 2d44b097bb net: mscc: ocelot: move NPI port configuration to DSA
Remove the ocelot_configure_cpu() function, which was in fact bringing
up 2 ports: the CPU port module, which both switchdev and DSA have, and
the NPI port, which only DSA has.

The (non-Ethernet) CPU port module is at a fixed index in the analyzer,
whereas the NPI port is selected through the "ethernet" property in the
device tree.

Therefore, the function to set up an NPI port is DSA-specific, so we
move it there, simplifying the ocelot switch library a little bit.

Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: UNGLinuxDriver <UNGLinuxDriver@microchip.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-26 14:17:58 -07:00
Xiaoliang Yang 4ab810a4e0 net: mscc: ocelot: fix fields offset in SG_CONFIG_REG_3
INIT_IPS and GATE_ENABLE fields have a wrong offset in SG_CONFIG_REG_3.
This register is used by stream gate control of PSFP, and it has not
been used before, because PSFP is not implemented in ocelot driver.

Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-24 20:00:40 -07:00
Vladimir Oltean e2f9a8fe73 net: mscc: ocelot: always pass skb clone to ocelot_port_add_txtstamp_skb
Currently, ocelot switchdev passes the skb directly to the function that
enqueues it to the list of skb's awaiting a TX timestamp. Whereas the
felix DSA driver first clones the skb, then passes the clone to this
queue.

This matters because in the case of felix, the common IRQ handler, which
is ocelot_get_txtstamp(), currently clones the clone, and frees the
original clone. This is useless and can be simplified by using
skb_complete_tx_timestamp() instead of skb_tstamp_tx().

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-24 19:47:56 -07:00
David S. Miller 3ab0a7a0c3 Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Two minor conflicts:

1) net/ipv4/route.c, adding a new local variable while
   moving another local variable and removing it's
   initial assignment.

2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
   One pretty prints the port mode differently, whilst another
   changes the driver to try and obtain the port mode from
   the port node rather than the switch node.

Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-22 16:45:34 -07:00
Li Yang 1fe44191f3 soc: fsl: qman: fix -Wpacked-not-aligned warnings
This fixes compile warnings from the -Wpacked-not-aligned option.

In file included from ../drivers/crypto/caam/qi.c:12:
../include/soc/fsl/qman.h:259:1: warning: alignment 1 of ‘struct qm_dqrr_entry’ is less than 8 [-Wpacked-not-aligned]
 } __packed;
 ^
../include/soc/fsl/qman.h:292:2: warning: alignment 1 of ‘struct <anonymous>’ is less than 8 [-Wpacked-not-aligned]
  } __packed ern;
  ^

Reported-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
2020-09-22 17:38:21 -05:00
Linus Torvalds d3017135c4 Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:

 - fix failure to add bond interfaces to a bridge, the offload-handling
   code was too defensive there and recent refactoring unearthed that.
   Users complained (Ido)

 - fix unnecessarily reflecting ECN bits within TOS values / QoS marking
   in TCP ACK and reset packets (Wei)

 - fix a deadlock with bpf iterator. Hopefully we're in the clear on
   this front now... (Yonghong)

 - BPF fix for clobbering r2 in bpf_gen_ld_abs (Daniel)

 - fix AQL on mt76 devices with FW rate control and add a couple of AQL
   issues in mac80211 code (Felix)

 - fix authentication issue with mwifiex (Maximilian)

 - WiFi connectivity fix: revert IGTK support in ti/wlcore (Mauro)

 - fix exception handling for multipath routes via same device (David
   Ahern)

 - revert back to a BH spin lock flavor for nsid_lock: there are paths
   which do require the BH context protection (Taehee)

 - fix interrupt / queue / NAPI handling in the lantiq driver (Hauke)

 - fix ife module load deadlock (Cong)

 - make an adjustment to netlink reply message type for code added in
   this release (the sole change touching uAPI here) (Michal)

 - a number of fixes for small NXP and Microchip switches (Vladimir)

[ Pull request acked by David: "you can expect more of this in the
  future as I try to delegate more things to Jakub" ]

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (167 commits)
  net: mscc: ocelot: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
  net: dsa: seville: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
  net: dsa: felix: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
  inet_diag: validate INET_DIAG_REQ_PROTOCOL attribute
  net: bridge: br_vlan_get_pvid_rcu() should dereference the VLAN group under RCU
  net: Update MAINTAINERS for MediaTek switch driver
  net/mlx5e: mlx5e_fec_in_caps() returns a boolean
  net/mlx5e: kTLS, Avoid kzalloc(GFP_KERNEL) under spinlock
  net/mlx5e: kTLS, Fix leak on resync error flow
  net/mlx5e: kTLS, Add missing dma_unmap in RX resync
  net/mlx5e: kTLS, Fix napi sync and possible use-after-free
  net/mlx5e: TLS, Do not expose FPGA TLS counter if not supported
  net/mlx5e: Fix using wrong stats_grps in mlx5e_update_ndo_stats()
  net/mlx5e: Fix multicast counter not up-to-date in "ip -s"
  net/mlx5e: Fix endianness when calculating pedit mask first bit
  net/mlx5e: Enable adding peer miss rules only if merged eswitch is supported
  net/mlx5e: CT: Fix freeing ct_label mapping
  net/mlx5e: Fix memory leak of tunnel info when rule under multipath not ready
  net/mlx5e: Use synchronize_rcu to sync with NAPI
  net/mlx5e: Use RCU to protect rq->xdp_prog
  ...
2020-09-22 14:43:50 -07:00
Vladimir Oltean 881321b6ed net: mscc: ocelot: make ocelot_init_timestamp take a const struct ptp_clock_info
It is a good measure to ensure correctness if the structures that are
meant to remain constant are only processed by functions that thake
constant arguments.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-18 17:52:40 -07:00
Vladimir Oltean e5fb512d81 net: mscc: ocelot: deinitialize only initialized ports
Currently mscc_ocelot_init_ports() will skip initializing a port when it
doesn't have a phy-handle, so the ocelot->ports[port] pointer will be
NULL. Take this into consideration when tearing down the driver, and add
a new function ocelot_deinit_port() to the switch library, mirror of
ocelot_init_port(), which needs to be called by the driver for all ports
it has initialized.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-18 13:52:34 -07:00
Vladimir Oltean 6565243c06 net: mscc: ocelot: add locking for the port TX timestamp ID
The ocelot_port->ts_id is used to:
(a) populate skb->cb[0] for matching the TX timestamp in the PTP IRQ
    with an skb.
(b) populate the REW_OP from the injection header of the ongoing skb.
Only then is ocelot_port->ts_id incremented.

This is a problem because, at least theoretically, another timestampable
skb might use the same ocelot_port->ts_id before that is incremented.
Normally all transmit calls are serialized by the netdev transmit
spinlock, but in this case, ocelot_port_add_txtstamp_skb() is also
called by DSA, which has started declaring the NETIF_F_LLTX feature
since commit 2b86cb8299 ("net: dsa: declare lockless TX feature for
slave ports").  So the logic of using and incrementing the timestamp id
should be atomic per port.

The solution is to use the global ocelot_port->ts_id only while
protected by the associated ocelot_port->ts_id_lock. That's where we
populate skb->cb[0]. Note that for ocelot, ocelot_port_add_txtstamp_skb
is called for the actual skb, but for felix, it is called for the skb's
clone. That is something which will also be changed in the future.

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2020-09-18 13:52:33 -07:00
Thierry Reding 1f44febf71 soc/tegra: fuse: Add Tegra234 support
Add support for FUSE block found on the Tegra234 SoC, which is largely
similar to the IP found on previous generations.

Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
2020-09-18 15:55:29 +02:00
Thierry Reding 52e6d399a4 soc/tegra: fuse: Implement tegra_is_silicon()
This function can be used by drivers to determine whether code is
running on silicon or on a simulation platform.

Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
2020-09-18 15:55:26 +02:00
Thierry Reding 775edf7856 soc/tegra: fuse: Extract tegra_get_platform()
This function extracts the PRE_SI_PLATFORM field from the HIDREV
register and can be used to determine which platform the kernel runs on
(silicon, simulation, ...). Note that while only Tegra194 and later
define this field, it should be safe to call this on prior generations
as well since this field should read as 0, indicating silicon.

Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
2020-09-18 15:55:22 +02:00
Greg Kroah-Hartman fccee0bace Merge 5.9-rc5 into usb-next
We need the USB fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-14 10:10:55 +02:00
Vineet Gupta 89d29997f1 irqchip/eznps: Fix build error for !ARC700 builds
eznps driver is supposed to be platform independent however it ends up
including stuff from inside arch/arc headers leading to rand config
build errors.

The quick hack to fix this (proper fix is too much chrun for non active
user-base) is to add following to nps platform agnostic header.
 - copy AUX_IENABLE from arch/arc header
 - move CTOP_AUX_IACK from arch/arc/plat-eznps/*/**

Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lkml.kernel.org/r/20200824095831.5lpkmkafelnvlpi2@linutronix.de
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
2020-08-27 13:15:17 -07:00
Nicolas Saenz Julienne 6b26057aab Revert "firmware: raspberrypi: Introduce vl805 init routine"
This reverts commit fbbc5ff3f7.

The vl805 init routine has moved into drivers/reset/reset-raspberrypi.c

Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20200629161845.6021-9-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-18 13:01:11 +02:00
Alexander A. Klimov 7f317d3490 include/: replace HTTP links with HTTPS ones
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.

Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: http://lkml.kernel.org/r/20200726110117.16346-1-grandmaster@al2klimov.de
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-08-12 10:57:59 -07:00
Linus Torvalds 30185b69a2 It looks like a smaller batch of clk updates this time around. In the core
framework we just have some minor tweaks and a debugfs feature, so not much to
 see there. The driver updates are fairly well split between AT91 and Qualcomm
 clk support. Adding those two drivers together equals about 50% of the
 diffstat. Otherwise, the big amount of work this time was on supporting
 Broadcom's Raspberry Pi firmware clks. See below for some more highlights.
 
 Core:
  - Document clk_hw_round_rate() so it gets some more use
  - Remove unused __clk_get_flags()
  - Add a prepare/enable debugfs feature similar to rate setting
 
 New Drivers:
  - Add support for SAMA7G5 SoC clks
  - Enable CPU clks on Qualcomm IPQ6018 SoCs
  - Enable CPU clks on Qualcomm MSM8996 SoCs
  - GPU clk support for Qualcomm SM8150 and SM8250 SoCs
  - Audio clks on Qualcomm SC7180 SoCs
  - Microchip Sparx5 DPLL clk
  - Add support for the new Renesas RZ/G2H (R8A774E1) SoC
 
 Updates:
  - Make defines for bcm63xx-gate clks to use in DT
  - Support BCM2711 SoC firmware clks
  - Add HDMI clks for BCM2711 SoCs
  - Add RTC related clks on Ingenic SoCs
  - Support USB PHY clks on Ingenic SoCs
  - Support gate clks on BCM6318 SoCs
  - RMU and DMAC/GPIO clock support for Actions Semi S500 SoCs
  - Use poll_timeout functions in Rockchip clk driver
  - Support Rockchip rk3288w SoC variant
  - Mark mac_lbtest critical on Rockchip rk3188
  - Add CAAM clock support for i.MX vf610 driver
  - Add MU root clock support for i.MX imx8mp driver
  - Amlogic g12: add neural network accelerator clock sources
  - Amlogic meson8: remove critical flag for main PLL divider
  - Amlogic meson8: add video decoder clock gates
  - Convert one more Renesas DT binding to json-schema
  - Enhance critical clock handling on Renesas platforms to only consider
    clocks that were enabled at boot time
 -----BEGIN PGP SIGNATURE-----
 
 iQJFBAABCAAvFiEE9L57QeeUxqYDyoaDrQKIl8bklSUFAl8tspERHHNib3lkQGtl
 cm5lbC5vcmcACgkQrQKIl8bklSX0og//TXp134IBXVZ2Z5Wca4J41itv7tPGJFsX
 EslQ/eMm6xhGEqqrA6BVsQ228JF9rUmg1fbvdl82UPK7Zyp9P2fo6CMC65ngDTky
 B1rLZOaKitER9JdL9DmmnIR772pI//rAMdIeVC/Jn5RR7OpP4lgY6+qvK0pJjVFl
 8aK3uHY+UWVFtqZxuJEAAyZBq1+bREqmVwNC1my6kmMIf0j0KwcGhrZgASWWtjQK
 4TRmroehLC4FBqnJ78Y3E6UAOBlz6C7XnP38qJge2672Ef7QhXZU7AGrGiTtxc4h
 5fB6MNMF+5QGel54qR1eH+JxaEoKsAjLaX1VBr7hAHrGIQ26dBFHFPsPvWDA+VVR
 4bwXJKz2objAWyqlMVM/cVV3q6uDixuScdrw2aAiojmV7ZvdZXflacdmZuS5v7e4
 sh86llN+lF0YrViYz33z+up0risCAi089xVo7Z99VgyLe2DR8TE+4/d6DQTFRNxl
 m66m6mlB9pPPgIV028SAf/zmzyoVWEarwdEAQPjJC6KVRbnR9mFlhSiTQMmCsSvU
 zHRxVcInc+8qIJY6VJ552UFu/JAan/AFl5knb+kW21a7hM8p81H9HuSnS4aHDDq4
 yETPU3XSMYz8ARHX4lKo1UIB6+k9iF2CWdCP+gXHNP+QYSAsRBIJsonjul9lLUCi
 8i6mUGkS0OU=
 =QLRg
 -----END PGP SIGNATURE-----

Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux

Pull clk updates from Stephen Boyd:
 "It looks like a smaller batch of clk updates this time around.

  In the core framework we just have some minor tweaks and a debugfs
  feature, so not much to see there. The driver updates are fairly well
  split between AT91 and Qualcomm clk support. Adding those two drivers
  together equals about 50% of the diffstat.

  Otherwise, the big amount of work this time was on supporting
  Broadcom's Raspberry Pi firmware clks.

  Highlights:

  Core:
   - Document clk_hw_round_rate() so it gets some more use
   - Remove unused __clk_get_flags()
   - Add a prepare/enable debugfs feature similar to rate setting

  New Drivers:
   - Add support for SAMA7G5 SoC clks
   - Enable CPU clks on Qualcomm IPQ6018 SoCs
   - Enable CPU clks on Qualcomm MSM8996 SoCs
   - GPU clk support for Qualcomm SM8150 and SM8250 SoCs
   - Audio clks on Qualcomm SC7180 SoCs
   - Microchip Sparx5 DPLL clk
   - Add support for the new Renesas RZ/G2H (R8A774E1) SoC

  Updates:
   - Make defines for bcm63xx-gate clks to use in DT
   - Support BCM2711 SoC firmware clks
   - Add HDMI clks for BCM2711 SoCs
   - Add RTC related clks on Ingenic SoCs
   - Support USB PHY clks on Ingenic SoCs
   - Support gate clks on BCM6318 SoCs
   - RMU and DMAC/GPIO clock support for Actions Semi S500 SoCs
   - Use poll_timeout functions in Rockchip clk driver
   - Support Rockchip rk3288w SoC variant
   - Mark mac_lbtest critical on Rockchip rk3188
   - Add CAAM clock support for i.MX vf610 driver
   - Add MU root clock support for i.MX imx8mp driver
   - Amlogic g12: add neural network accelerator clock sources
   - Amlogic meson8: remove critical flag for main PLL divider
   - Amlogic meson8: add video decoder clock gates
   - Convert one more Renesas DT binding to json-schema
   - Enhance critical clock handling on Renesas platforms to only
     consider clocks that were enabled at boot time"

* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (79 commits)
  clk: qcom: gcc: Make disp gpll0 branch aon for sc7180/sdm845
  ipq806x: gcc: add support for child probe
  clk: qcom: msm8996: Make symbol 'cpu_msm8996_clks' static
  clk: qcom: ipq8074: Add correct index for PCIe clocks
  clk: <linux/clk-provider.h>: drop a duplicated word
  clk: renesas: cpg-mssr: Add r8a774e1 support
  dt-bindings: clock: renesas,cpg-mssr: Document r8a774e1
  clk: Drop duplicate selection in Kconfig
  clk: qcom: smd: Add support for MSM8992/4 rpm clocks
  clk: qcom: ipq8074: Add missing clocks for pcie
  dt-bindings: clock: qcom: ipq8074: Add missing bindings for PCIe
  Replace HTTP links with HTTPS ones: Common CLK framework
  clk: qcom: Add CPU clock driver for msm8996
  dt-bindings: clk: qcom: Add bindings for CPU clock for msm8996
  soc: qcom: Separate kryo l2 accessors from PMU driver
  clk: meson: meson8b: add the vclk2_en gate clock
  clk: meson: meson8b: add the vclk_en gate clock
  clk: qcom: Fix return value check in apss_ipq6018_probe()
  clk: bcm: dvp: Add missing module informations
  clk: meson: meson8b: Drop CLK_IS_CRITICAL from fclk_div2
  ...
2020-08-07 13:35:51 -07:00
Linus Torvalds 47ec5303d7 Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from David Miller:

 1) Support 6Ghz band in ath11k driver, from Rajkumar Manoharan.

 2) Support UDP segmentation in code TSO code, from Eric Dumazet.

 3) Allow flashing different flash images in cxgb4 driver, from Vishal
    Kulkarni.

 4) Add drop frames counter and flow status to tc flower offloading,
    from Po Liu.

 5) Support n-tuple filters in cxgb4, from Vishal Kulkarni.

 6) Various new indirect call avoidance, from Eric Dumazet and Brian
    Vazquez.

 7) Fix BPF verifier failures on 32-bit pointer arithmetic, from
    Yonghong Song.

 8) Support querying and setting hardware address of a port function via
    devlink, use this in mlx5, from Parav Pandit.

 9) Support hw ipsec offload on bonding slaves, from Jarod Wilson.

10) Switch qca8k driver over to phylink, from Jonathan McDowell.

11) In bpftool, show list of processes holding BPF FD references to
    maps, programs, links, and btf objects. From Andrii Nakryiko.

12) Several conversions over to generic power management, from Vaibhav
    Gupta.

13) Add support for SO_KEEPALIVE et al. to bpf_setsockopt(), from Dmitry
    Yakunin.

14) Various https url conversions, from Alexander A. Klimov.

15) Timestamping and PHC support for mscc PHY driver, from Antoine
    Tenart.

16) Support bpf iterating over tcp and udp sockets, from Yonghong Song.

17) Support 5GBASE-T i40e NICs, from Aleksandr Loktionov.

18) Add kTLS RX HW offload support to mlx5e, from Tariq Toukan.

19) Fix the ->ndo_start_xmit() return type to be netdev_tx_t in several
    drivers. From Luc Van Oostenryck.

20) XDP support for xen-netfront, from Denis Kirjanov.

21) Support receive buffer autotuning in MPTCP, from Florian Westphal.

22) Support EF100 chip in sfc driver, from Edward Cree.

23) Add XDP support to mvpp2 driver, from Matteo Croce.

24) Support MPTCP in sock_diag, from Paolo Abeni.

25) Commonize UDP tunnel offloading code by creating udp_tunnel_nic
    infrastructure, from Jakub Kicinski.

26) Several pci_ --> dma_ API conversions, from Christophe JAILLET.

27) Add FLOW_ACTION_POLICE support to mlxsw, from Ido Schimmel.

28) Add SK_LOOKUP bpf program type, from Jakub Sitnicki.

29) Refactor a lot of networking socket option handling code in order to
    avoid set_fs() calls, from Christoph Hellwig.

30) Add rfc4884 support to icmp code, from Willem de Bruijn.

31) Support TBF offload in dpaa2-eth driver, from Ioana Ciornei.

32) Support XDP_REDIRECT in qede driver, from Alexander Lobakin.

33) Support PCI relaxed ordering in mlx5 driver, from Aya Levin.

34) Support TCP syncookies in MPTCP, from Flowian Westphal.

35) Fix several tricky cases of PMTU handling wrt. briding, from Stefano
    Brivio.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2056 commits)
  net: thunderx: initialize VF's mailbox mutex before first usage
  usb: hso: remove bogus check for EINPROGRESS
  usb: hso: no complaint about kmalloc failure
  hso: fix bailout in error case of probe
  ip_tunnel_core: Fix build for archs without _HAVE_ARCH_IPV6_CSUM
  selftests/net: relax cpu affinity requirement in msg_zerocopy test
  mptcp: be careful on subflow creation
  selftests: rtnetlink: make kci_test_encap() return sub-test result
  selftests: rtnetlink: correct the final return value for the test
  net: dsa: sja1105: use detected device id instead of DT one on mismatch
  tipc: set ub->ifindex for local ipv6 address
  ipv6: add ipv6_dev_find()
  net: openvswitch: silence suspicious RCU usage warning
  Revert "vxlan: fix tos value before xmit"
  ptp: only allow phase values lower than 1 period
  farsync: switch from 'pci_' to 'dma_' API
  wan: wanxl: switch from 'pci_' to 'dma_' API
  hv_netvsc: do not use VF device if link is down
  dpaa2-eth: Fix passing zero to 'PTR_ERR' warning
  net: macb: Properly handle phylink on at91sam9x
  ...
2020-08-05 20:13:21 -07:00
Linus Torvalds 442489c219 Time, timers and related driver updates:
- Prevent unnecessary timer softirq invocations by extending the tracking
    of the next expiring timer in the timer wheel beyond the existing NOHZ
    functionality. The tracking overhead at enqueue time is within the
    noise, but on sensitive workloads the avoidance of the soft interrupt
    invocation is a measurable improvement.
 
  - The obligatory new clocksource driver for Ingenic X100 OST
 
  - The usual fixes, improvements, cleanups and extensions for newer chip
    variants all over the driver space.
 -----BEGIN PGP SIGNATURE-----
 
 iQJHBAABCgAxFiEEQp8+kY+LLUocC4bMphj1TA10mKEFAl8pD7ITHHRnbHhAbGlu
 dXRyb25peC5kZQAKCRCmGPVMDXSYoRIXD/9VRiGKHIP27O0aoPj9HGFiZyY+bXbC
 xv5HA9CTlJjG23JTZWg13Kk26l8+mzIJoH54nMnceVDdCwPb1e7iRFgefyHOgEW4
 oKpJnwqvGOA9cvAnu8Tl9oNNILUoS2k0dHDeGICMCOqqjycUoKGRPpiizsbXZ08x
 yOLUMktX0wtNnL6DOqOpvmfN+b3T8gO0fuNzgRcvcHZpamQxo7wN2P05mt9nmWLV
 zfEwyhn33Xy9toGPZfkbCYNzVSI3fkMXuMDIkLo5jOtt18i06AeUZov8Z0V7xk9B
 S1lu2HmP4PnX00/P7KB8LwtlhzhM/H7IxK4bxYJYlHmGcd2hJHjKdIfCg3bqo41d
 YmsIelukI3jLvnrB6YXyWx3mt1a8p/i3zf/+Fwqs81qV/60FXhp0zD2QnltJEEC3
 INXrb93CkC5vMqOs0otizL5cPnPhTS0fMe/GhnHlsteUXlqEeJ1HU5f+j0FFaIJA
 h+dEPT57eJwDyuh6iWNHjvAI/HtLSBTsHC0CPWa+DxHKxzItZWpiVl+EEw5ofepX
 zJyf8nxq1nOMDOROCiTxdbyp4yacDk3dak/trbRZCfX9fapSuzJFzDRCM0Ums2lH
 lh12jR9nRZgKb5atC31UUpw4HYZfvcbj2NGr27SAx9b3hh5q6SRW8yowL8tta1lK
 /Afs0OhmQS5Raw==
 =uJnp
 -----END PGP SIGNATURE-----

Merge tag 'timers-core-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull timer updates from Thomas Gleixner:
 "Time, timers and related driver updates:

   - Prevent unnecessary timer softirq invocations by extending the
     tracking of the next expiring timer in the timer wheel beyond the
     existing NOHZ functionality.

     The tracking overhead at enqueue time is within the noise, but on
     sensitive workloads the avoidance of the soft interrupt invocation
     is a measurable improvement.

   - The obligatory new clocksource driver for Ingenic X100 OST

   - The usual fixes, improvements, cleanups and extensions for newer
     chip variants all over the driver space"

* tag 'timers-core-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (28 commits)
  timers: Recalculate next timer interrupt only when necessary
  clocksource/drivers/ingenic: Add support for the Ingenic X1000 OST.
  dt-bindings: timer: Add Ingenic X1000 OST bindings.
  clocksource/drivers: Replace HTTP links with HTTPS ones
  clocksource/drivers/nomadik-mtu: Handle 32kHz clock
  clocksource/drivers/sh_cmt: Use "kHz" for kilohertz
  clocksource/drivers/imx: Add support for i.MX TPM driver with ARM64
  clocksource/drivers/ingenic: Add high resolution timer support for SMP/SMT.
  timers: Lower base clock forwarding threshold
  timers: Remove must_forward_clk
  timers: Spare timer softirq until next expiry
  timers: Expand clk forward logic beyond nohz
  timers: Reuse next expiry cache after nohz exit
  timers: Always keep track of next expiry
  timers: Optimize _next_timer_interrupt() level iteration
  timers: Add comments about calc_index() ceiling work
  timers: Move trigger_dyntick_cpu() to enqueue_timer()
  timers: Use only bucket expiry for base->next_expiry value
  timers: Preserve higher bits of expiration on index calculation
  clocksource/drivers/timer-atmel-tcb: Add sama5d2 support
  ...
2020-08-04 18:17:37 -07:00
Thomas Gleixner 1b7efaa615 - Add sama5d2 support and rework the 32kHz clock handling (Alexandre Belloni)
- Add the high resolution support for SMP/SMT on the Ingenic timer (Zhou Yanjie)
 
 - Add support for i.MX TPM driver with ARM64 (Anson Huang)
 
 - Fix typo by replacing KHz to kHz (Geert Uytterhoeven)
 
 - Add 32kHz support by setting the minimum ticks to 5 on Nomadik MTU (Linus Walleij)
 
 - Replace HTTP links with HTTPS ones for security reasons (Alexander A. Klimov)
 
 - Add support for the Ingenic X1000 OST (Zhou Yanjie)
 -----BEGIN PGP SIGNATURE-----
 
 iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl8ZqeUACgkQqDIjiipP
 6E9tawf/UGUhEfB+VmH9w60NJlM0fC5a/TjVOb4yMjTZjjdyd4zMBHemF+dqMNnw
 wTr+S8U9QfvP4BDgg1hWV+vhAwxz2xkhR0cGtOQjck5322vZglGSmAVqTCAlQMoZ
 LNm98XeUYYVNMB+/+BHkf8F/nHV9vRo8sJg7UnvX/6RCykXFYXVP+P8LfkAU1MPt
 8vaRPCcyGnYXrgjDYY5M5qYudLNpFPrzr1yJDWdwWUliwH3T1X1FNogTdUo955qk
 wM+Hb4yPRuRufM+yATPsRedQypZFpoWFObuEMD2FaIw/LZVxV7D1tmw5KhL2V1tZ
 XSzNiJDEgri/4LaVzXKP7sVlQlZfDQ==
 =DXTp
 -----END PGP SIGNATURE-----

Merge tag 'timers-v5.9' of https://git.linaro.org/people/daniel.lezcano/linux into timers/core

Pull clock event/surce driver changes from Daniel Lezcano:

  - Add sama5d2 support and rework the 32kHz clock handling (Alexandre Belloni)
  - Add the high resolution support for SMP/SMT on the Ingenic timer (Zhou Yanjie)
  - Add support for i.MX TPM driver with ARM64 (Anson Huang)
  - Fix typo by replacing KHz to kHz (Geert Uytterhoeven)
  - Add 32kHz support by setting the minimum ticks to 5 on Nomadik MTU (Linus Walleij)
  - Replace HTTP links with HTTPS ones for security reasons (Alexander A. Klimov)
  - Add support for the Ingenic X1000 OST (Zhou Yanjie)
2020-07-23 21:04:05 +02:00