The Dialog PMIC has below featured regulators:-
DA9052-BC - 4 DVS Buck converters 0.5V - 3.6V upto 1Amp.
DA9053-AA/BX - 4 DVS Buck converters 0.5V - 2.5V upto 3Amp.
DA9052/53 - 10 Programmable LDO's High PSSR, 1% accuracy.
This patch support all the DA9052 and Da9053 regulators. The output voltages are
fully programmable via I2C or SPI interface. The platform data with regulation
constraints is passed down from the board to the regulator.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Without GENERIC_GPIO "struct gpio" is undefined leading to errors.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds support for regulators that can be controlled via gpios.
Examples for such regulators are the TI-tps65024x voltage regulators
with 4 fixed and 1 runtime-switchable voltage regulators
or the TI-bq240XX charger regulators.
The number of controlling gpios is not limited, the mapping between
voltage/current and target gpio state is done via the states map
and the driver can be used for either voltage or current regulators.
A mapping for a regulator with two GPIOs could look like:
gpios = {
{ .gpio = GPIO1, .flags = GPIOF_OUT_INIT_HIGH, .label = "gpio name 1" },
{ .gpio = GPIO2, .flags = GPIOF_OUT_INIT_LOW, .label = "gpio name 2" },
}
The flags element of the gpios array determines the initial state of
the gpio, set during probe. The initial state of the regulator is also
calculated from these values
states = {
{ .value = volt_or_cur1, .gpios = (0 << 1) | (0 << 0) },
{ .value = volt_or_cur2, .gpios = (0 << 1) | (1 << 0) },
{ .value = volt_or_cur3, .gpios = (1 << 1) | (0 << 0) },
{ .value = volt_or_cur4, .gpios = (1 << 1) | (1 << 0) },
}
The target-state for the n-th gpio is determined by the n-th bit
in the bitfield of the target-value.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add regulator driver for AnalogicTech AAT2870.
Signed-off-by: Jin Park <jinyoungp@nvidia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The tps65912 consist of 4 DCDCs and 10 LDOs. The output voltages can be
configured by the SPI or I2C interface, they are meant to supply power
to the main processor and other components.
Signed-off-by: Margarita Olaya Cabrera <magi@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
The regulator module consists of 3 DCDCs and 8 LDOs. The output
voltages are configurable and are meant to supply power to the
main processor and other components
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The DB8500 has ePOD:s (electronic power domains) which are possible
to switch on/off to deactivate silicon blocks on the DB8500 SoC
by cutting their power without retention. We model these as simple
regulators with one bit on/off settings.
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Martin Persson <martin.persson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix typo: s/TPS695x0/TPS659x0/
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This adds a subdriver for the regulator found inside the TPS61050
and TPS61052 chips.
Cc: Samuel Ortiz <samuel.ortiz@intel.com>
Cc: Ola Lilja <ola.o.lilja@stericsson.com>
Cc: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch supports PMIC/Regulator part of MAX8997/MAX8966 MFD.
In this initial release, selecting voltages or current-limit
and switching on/off the regulators are supported.
Controlling voltages for DVS with GPIOs is not implemented fully
and requires more considerations: it controls multiple bucks (selection
of 1, 2, and 5) at the same time with SET1~3 gpios. Thus, when DVS-GPIO
is activated, we lose the ability to control the voltage of a single
buck regulator independently; i.e., contolling a buck affects other two
bucks. Therefore, using the conventional regulator framework directly
might be problematic. However, in this driver, we try to choose
a setting without such side effect of affecting other regulators and
then try to choose a setting with the minimum side effect (the sum of
voltage changes in other regulators).
On the other hand, controlling all the three bucks simultenously based
on the voltage set table may help build cpufreq and similar system
more robust; i.e., all the three voltages are consistent every time
without glitches during transition.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since the MFD core for this device and the regulator drivers for these
devices can be built modular we should also support modular build of
the shared code for the regulator drivers, otherwise we try to link
built in code against modular code with unfortunate results.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
move some common functions and micros of mc13783 regulaor driver to
a seperate file, which makes it possible for mc13892 to share code.
Signed-off-by: Yong Shen <yong.shen@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
TPS6524X provides three step-down converters and two general-purpose LDO
voltage regulators. This device is interfaced using SPI.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds regulator drivers for National Semiconductors LP3972 PMIC.
This LP3972 PMIC controller has 3 DC/DC voltage converters and 5 low drop-out
(LDO) regulators. LP3972 PMIC controller uses I2C interface.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
MAX8952 PMIC is used to provide voltage output between 770mV - 1400mV
with DVS support. In this initial release, users can set voltages for
four DVS modes, RAMP delay values, and SYNC frequency.
Controlling FPWM/SYNC_MODE/Pull-Down/Ramp Modes and reading CHIP_ID
is not supported in this release.
If GPIO of EN is not valid in platform data, the driver assumes that it
is always-on. If GPIO of VID0 or VID1 is invalid, the driver pulls down
VID0 and VID1 to fix DVS mode as 0 and disables DVS support.
We assume that V_OUT is capable to provide every voltage from 770mV to
1.40V in 10mV steps although the data sheet has some ambiguity on it.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
--
v2:
- Style correction
- Can accept platform_data with invalid GPIOs
- Removed unnecessary features
- Improved error handling
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Hi Mark,
> I think that's everything.
Please find the updated patch set as below.
>From f4bf7eec4d210db5075c0bce4521d9be6bc76c8c Mon Sep 17 00:00:00 2001
From: Sundar R Iyer <sundar.iyer@stericsson.com>
Date: Sun, 6 Jun 2010 19:12:12 +0530
Subject: [PATCH v3 1/2] regulator: add support for regulators on the ab8500 MFD
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Bengt JONSSON <bengt.g.jonsson@stericsson.com>
Signed-off-by: Sundar R Iyer <sundar.iyer@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The MAX8998-pmic driver requires a core driver for all io operations. Like
other regulator driver make it depend of the required MFD io driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds voltage regulator driver for Maxim 8998 chip. This chip
is used on Samsung Aquila and GONI boards and provides following
functionalities:
- 4 BUCK voltage converters, 17 LDO power regulators and 5 other power
controllers
- battery charger
This patch adds basic driver for voltage regulators and MAX 8998 MFD core.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This device is very simple, it supports one buck and two LDOs. The LDOs are
fixed-voltage. Only the buck is programable over the I2C bus to 16 possible
voltages.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The AD5398 and AD5821 are single 10-bit DAC with 120 mA output current
sink capability. They feature an internal reference and operates from
a single 2.7 V to 5.5 V supply.
This driver supports both the AD5398 and the AD5821. It adapts into the
voltage and current framework.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
MAX8925 contains 3 Buck and 20 LDO regulator.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Rename 88PM8607 to 88PM860X in both Makefile and Kconfig under mfd directory.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to ease transitions with drivers are boards start using regulators
provide an option to cause all regulator_get() calls to succeed, with a
dummy always on regulator being supplied where one has not been configured.
A warning is printed whenever the dummy regulator is used to aid system
development.
This regulator does not implement any regulator operations but will allow
simple consumers which only do enable() and disable() calls to run. It
is kept separate from the fixed voltage regulator to avoid Kconfig
confusion on the part of users when it is extended to allow boards to
explicitly use the dummy regulator to simplify cases where the majority
of supplies are from fixed regulators without software control.
This option is currently only effective for systems which do not specify
full constriants. If required an override could also be provided to allow
these systems to use the dummy regulator, though it is likely that
unconfigured supplies on such systems will lead to error due to
regulators being powered down more aggressively when not in use.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8994 contains two LDOs with mixed hardware/software control to
minimise the number of external supplies required while delivering
optimal voltages to minimise power consumption.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Fix Kconfig text for some Wolfson Micro devices.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Hi Liam,
Since Samuel merged a new version of mfd 88pm8607 driver, I format a
new patch on regulator 88pm8607. I paste the new patch in mail. Please
help to review again. And I also attach the mfd driver in mail.
From: Haojian Zhuang <haojian.zhuang@marvell.com>
Date: Thu, 8 Oct 2009 09:36:53 -0400
Subject: [PATCH] regulator: Add 88PM8607 PMIC driver
This patch adds regulator drivers for Marvell 88PM8607 PMIC.
This controller contains 3 DVC and 14 LDO regulators. This controller
uses I2C interface.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Tested with a MX25-based custom board.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch updates the regulator driver to add support
for TWL6030 PMIC specific LDO regulators.
SMPS resources are not yet supported for TWL6030 and
also .set_mode and .get_status for LDO's are yet to
be implemented for TWL6030.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Specifying 'default n' is superfluous.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Adding TPS65023 and TPS6507x regulator driver support in
drivers/regulator/Makefile and drivers/regulator/Kconfig
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This adds support for the regulators found in the AB3100
Mixed-Signal IC.
It further also defines platform data for the ST-Ericsson
U300 platform and extends the AB3100 MFD driver so that
platform/board data with regulation constraints and an init
function can be passed down all the way from the board to
the regulators.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This driver provides basic support for the voltage regulators
integrated into the Freescale MC13783 PMIC. It is currently
only possible to enable/disable outputs, not to actually
set the voltage.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x series of devices all have 3 DC-DC buck convertors. This
driver implements software control for these regulators via the
regulator API. Use with split hardware/software control of individual
regulators is not supported, though regulators not controlled by
software may be controlled via the hardware control interfaces.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add (partial) support for the voltage regulators on the PCAP2 PMIC.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds regulator drivers for National Semiconductors LP3971 PMIC.
This LP3971 PMIC controller has 3 DC/DC voltage converters and 5 low
drop-out (LDO) regulators. LP3971 PMIC controller uses I2C interface.
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The userspace-consumer driver allows control of voltage and current
regulator state from userspace. This is required for fine-grained
power management of devices that are completely controller by userspace
applications, e.g. a GPS transciever connected to a serial port.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The Maxim 1586 regulator is a voltage regulator with 2
voltage outputs, specially suitable for Marvell PXA
chips. One output is in the range of required VCC_CORE by
the PXA27x chips, the other in the VCC_USIM required as well
by PXA27x chips.
The chip is controlled through the I2C bus.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Support most of the LDO regulators in the twl4030 family chips.
In the case of LDOs supporting MMC/SD, the voltage controls are
used; but in most other cases, the regulator framework is only
used to enable/disable a supplies, conserving power when a given
voltage rail is not needed.
The drivers/mfd/twl4030-core.c code already sets up the various
regulators according to board-specific configuration, and knows
that some chips don't provide the full set of voltage rails.
The omitted regulators are intended to be under hardware control,
such as during the hardware-mediated system powerup, powerdown,
and suspend states. Unless/until software hooks are known to
be safe, they won't be exported here.
These regulators implement the new get_status() operation, but
can't realistically implement get_mode(); the status output is
effectively the result of a vote, with the relevant hardware
inputs not exposed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This allows users to enable or disable support for these regulators at
build time as they can for other regulators rather than having platforms
force the regulators to be built in.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Changes from V1:
- Removed support for suspend_enable & suspend_disable functions.
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Use menuconfig instead of flat configs so that you can disable/enable
regulator items with one selection. Also, use depends instead of
reverse selections to make life easier, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8350 features six DCDC convertors (four buck and two boost), four
LDO voltage regulators and two constant current sinks. This driver adds
support for these through the regulator API.
This driver was written by Liam Girdwood with updates for submission
from Mark Brown.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Ashish Jangam