Support creating and destroying XRC domains. Any sharing of the XRCD
is managed above the low-level driver.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Allocate flow counter per Ethernet/IBoE port, and attach this counter
to all the QPs created on that port. Based on patch by Eli Cohen
<eli@mellanox.co.il>.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
IBoE doesn't use LIDs. Use the GID change event to update the IB core
cache for addition/deletion of GIDs.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The same packet steering mechanism would be used both for IB and Ethernet,
Both multicasts and unicasts.
This commit prepares the general infrastructure for this.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW revision is derived from device ID and rev id.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newest device firmware stores IB vs. Ethernet protocol in two bits
in members_count field of multicast group table (0: Infiniband, 1:
Ethernet). When changing the QP members count for a multicast group,
it important not to reset this information. When calling multicast
attach first time, the protocol type should be specified. In this
patch we always set it IB, but in the future we will handle Ethernet
too. When looking for a QP, the protocol type shoud be checked too.
Signed-off-by: Aleksey Senin <alekseys@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some systems have PCI addresses that don't fit in unsigned long (eg some
32-bit PowerPC 440 systems have 36-bit bus addresses). Fix up mlx4 drivers
by using phys_addr_t where appropriate, so we don't truncate any PCI
resource addresses before ioremapping them.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use netif_running() and netif_carrier_ok() to report link state,
exactly as is done to report Ethernet link state in sysfs.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The link rate is the product of the link speed in the link width. For
Etherent ports the rate is 10G, so we use 1 for the width and 4 for
speed to get the correct rate.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
dev_base_lock is the legacy way to lock the device list, and is planned
to disappear. (writers hold RTNL, readers hold RCU lock)
Convert rdma_translate_ip() and update_ipv6_gids() to RCU locking.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows IBoE traffic to be encapsulated in 802.1Q tagged
VLAN frames. The VLAN tag is encoded in the GID and derived from it
by a simple computation.
The netdev notifier callback is modified to catch VLAN device
addition/removal and the port's GID table is updated to reflect the
change, so that for each netdevice there is an entry in the GID table.
When the port's GID table is exhausted, GID entries will not be added.
Only children of the main interfaces can add to the GID table; if a
VLAN interface is added on another VLAN interface (e.g. "vconfig add
eth2.6 8"), then that interfaces will not add an entry to the GID
table.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for IBoE to mlx4_ib. The bulk of the code is handling the
new address vector fields; mlx4 needs the MAC address of a remote node
to include it in a WQE (for datagrams) or in the QP context (for
connected QPs). Address resolution is done by assuming all unicast
GIDs are either link-local IPv6 addresses.
Multicast group attach/detach needs to update the NIC's multicast
filters; but since attaching a QP to a multicast group can be done
before the QP is bound to a port, for IBoE we need to keep track of
all multicast groups that a QP is attached too before it transitions
from INIT to RTR (since it does not have a port in the INIT state).
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
[ Many things cleaned up and otherwise monkeyed with; hope I didn't
introduce too many bugs. - Roland ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The Node Description cannot be changed via MADs (it is read-only).
Until now, it was changed in the driver via sysfs, and the new Node
Description was simply inserted by the driver into MAD responses
(replacing the description returned by FW).
System startup scripts use the sysfs interface to change the node
description at driver startup to show the hostname, etc. However, this
has a race condition: the SM could discover the original FW node
description rather than the system-specific description if it queried the
port before the startup scripts finish running.
For mlx4, we fix this with a new FW command (SET_NODE) that allows
passing the new node description to FW. When this command is invoked,
FW sends a trap 144 to the SM. When it gets this trap, the SM can
query the node to obtain the new node description -- thus eliminating
the effects of the race.
This patch simply calls SET_NODE command when a new node description
is entered via sysfs (thus causing trap 144 to be issued by the FW).
We ignore all failures of the SET_NODE command (including those caused
by using a device FW that predates the SET_NODE command), since in
that case things work just as before.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix the limit on the size of max fast registration WRs that can be
posted to match hardware capabilities.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a new parameter to ib_register_device() so that low-level device
drivers can pass in a pointer to a callback function that will be
called for each port that is registered in sysfs. This allows
low-level device drivers to create files in
/sys/class/infiniband/<hca>/ports/<N>/
without having to poke through the internals of the RDMA sysfs handling.
There is no need for an unregister function since the kobject
reference will go to zero when ib_unregister_device() is called.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for masked atomic operations (masked compare and swap,
masked fetch and add).
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Current code has a limitation: an LSO header is not allowed to cross a
64 byte boundary. This patch removes this limitation by setting the
WQE RR for large headers thus allowing LSO headers of any size. The
extra buffer reserved for MLX4_IB_QP_LSO QPs has been doubled, from 64
to 128 bytes, assuming this is reasonable upper limit for header
length. Also, this patch will cause IB_DEVICE_UD_TSO to be set only
for HCA FW versions that set MLX4_DEV_CAP_FLAG_BLH; e.g. FW version
2.6.000 and higher.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Userspace apps are supposed to release all ib device resources if they
receive a fatal async event (IBV_EVENT_DEVICE_FATAL). However, the
app has no way of knowing when the device has come back up, except to
repeatedly attempt ibv_open_device() until it succeeds.
However, currently there is no protection against the open succeeding
while the device is in being removed following the fatal event. In
this case, the open will succeed, but as a result the device waits in
the middle of its removal until the new app releases its resources --
and the new app will not do so, since the open succeeded at a point
following the fatal event generation.
This patch adds an "active" flag to the device. The active flag is set
to false (in the fatal event flow) before the "fatal" event is
generated, so any subsequent ibv_dev_open() call to the device will
fail until the device comes back up, thus preventing the above
deadlock.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Replace open-coded reimplementations with printk_once().
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The PAT work on x86 has finally made pgprot_writecombine() a usable API
for modular drivers. As the comment indicates, this is exactly what we
want to use in mlx4_ib to map BlueFlame pages up to userspace, since
using WC for these pages improves small message latency significantly.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
According to the ConnectX programmer's reference manual, all
operations should be stopped, all QPs should be torn down and all WQEs
flushed before the CLOSE_PORT command is invoked. In some cases
reversing the order of operations (as implemented now) could cause
a loss of completions.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the mlx4_ib driver finds an adapter that has only ethernet ports, the
current code will register an IB device with 0 ports. Nothing useful or
sensible can be done with such a device, so just skip registering it.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When using MSI-X mode, create a completion event queue for each CPU.
Report the number of completion EQs in a new struct mlx4_caps member,
num_comp_vectors, and extend the mlx4_cq_alloc() interface with a
vector parameter so that consumers can specify which completion EQ
should be used to report events for the CQ being created.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Multi-protocol adapters support different port types. Each consumer
of mlx4_core queries for supported port types; in particular mlx4_ib
can no longer assume that all physical ports belong to it. Port type
is configured through a sysfs interface. When the type of a port is
changed, all mlx4 interfaces are unregistered, and then registered
again with the new port types.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Update existing Mellanox copyright lines to 2008, and add such lines
to files where they are missing.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for the following operations to mlx4 when device firmware
supports them:
- Send with invalidate and local invalidate send queue work requests;
- Allocate/free fast register MRs;
- Allocate/free fast register MR page lists;
- Fast register MR send queue work requests;
- Local DMA L_Key.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for handling the IB_QP_CREATE_MULTICAST_BLOCK_LOOPBACK
flag by using the per-multicast group loopback blocking feature of
mlx4 hardware.
Signed-off-by: Ron Livne <ronli@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In addition to mlx4_ib, there will be ethernet and FC consumers of
mlx4_core, so move the code for managing kernel doorbells into the
core module to avoid having to duplicate this multiple times.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This converts the main ib_device to use struct device instead of struct
class_device as class_device is going away.
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The mlx4_ib driver is stable enough for production use, so bump the
version number to 1.0 to indicate this.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ConnectX devices support checksum generation and verification of TCP
and UDP packets for UD IPoIB messages. This patch checks if the HCA
supports this and sets the IB_DEVICE_UD_IP_CSUM capability flag if it
does. It implements support for handling the IB_SEND_IP_CSUM send
flag and setting the csum_ok field in receive work completions.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Ali Ayub <ali@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The struct mlx4_interface.event() method was supposed to get an enum
mlx4_dev_event, but the driver code was actually passing in the
hardware enum mlx4_event values. Fix up the callers of
mlx4_dispatch_event() so that they pass in the right type of value,
and fix up the event method in mlx4_ib so that it can handle the enum
mlx4_dev_event values.
This eliminates the need for the subtype parameter to the event
method, so remove it.
This also fixes the sparse warning
drivers/net/mlx4/intf.c:127:48: warning: mixing different enum types
drivers/net/mlx4/intf.c:127:48: int enum mlx4_event versus
drivers/net/mlx4/intf.c:127:48: int enum mlx4_dev_event
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The string mlx4_ib_version was defined, but never used. Print out the
version once when the first device is initialized.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The firmware QUERY_ADAPTER command does not return vendor_id,
device_id, and revision_id; eliminate these fields from the query.
Initialize the rev_id field of the mlx4 device via init_node_data (MAD
IFC query), as is done in the query_device verb implementation.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Implement FMRs for mlx4. This is an adaptation of code from mthca.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
display the following device information under /sys/class/infiniband/mlx4_X:
board_id, fw_ver, hw_rev, hca_type.
This patch makes this information available to userspace utilities
such as ibstat and ibv_devinfo.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Get the maximum message size from the device capabilities returned
from the QUERY_DEV_CAP firmware command, rather than hard-coding 2 GB.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We need to keep a spare entry in the SRQ so that there always is a
next WQE available when posting receives (so that we can tell the
difference between a full queue and an empty queue). So subtract 1
from the value HW gives us before reporting the limit on SRQ entries
to consumers.
Found by Mellanox QA.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Upcoming firmware introduces command interface revision 3, which
changes the way port capabilities are queried and set. Update the
driver to handle both the new and old command interfaces by adding a
new MLX4_FLAG_OLD_PORT_CMDS that it is set after querying the firmware
interface revision and then using the correct interface based on the
setting of the flag.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
uar_lock spinlock was used in mlx4_ib_cq_arm without being initialized
(this only affects 32-bit archs, because uar_lock is not used on
64-bit archs and MLX4_INIT_DOORBELL_LOCK() is a NOP).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add an InfiniBand driver for Mellanox ConnectX adapters. Because
these adapters can also be used as ethernet NICs and Fibre Channel
HBAs, the driver is split into two modules:
mlx4_core: Handles low-level things like device initialization and
processing firmware commands. Also controls resource allocation
so that the InfiniBand, ethernet and FC functions can share a
device without stepping on each other.
mlx4_ib: Handles InfiniBand-specific things; plugs into the
InfiniBand midlayer.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Sean Hefty