GEM has configurable receive buffer sizes so requires this to be
programmed up. Any size < 2048 and a multiple of 64 bytes is permitted.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Some GEM implementations may support DMA bus widths up to 128 bits. We
can get the maximum supported DMA bus width from the design
configuration register so use that to program the device up.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
GEM devices have a different number of statistics registers and they
are at a different offset to MACB devices. Make the statistics
collection method dependent on device type.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
GEM devices support larger clock divisors and have a different
range of divisors. Program the MDIO clock divisors based on the
device type.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The Cadence GEM is based on the MACB Ethernet controller but has a few
small changes with regards to register and bitfield placement. This
patch detects the presence of a GEM by reading the module ID register
and setting a flag appropriately.
This handles the new HW address, USRIO and hash register base register
locations in GEM.
v3: - convert to macb_is_gem() inline rather than storing a boolean
flag
- handle rx_overrun stats for gem
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
macb is already using the dev_dbg() and friends helpers so use netdev_()
along with a pr_fmt() definition to make the printing a little cleaner.
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Both at91 and avr32 defines its own platform data structure for
the macb driver and both share common structures though at91
includes a currently unused phy_irq_pin. Create a common
macb_platform_data for macb that both at91 and avr32 can use. In
future we can use this to support other architectures that use the
same IP block with the macb driver.
v2: rename eth_platform_data to macb_platform_data and allow at91_ether
to share the platform data with macb.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
AT91 now provides both "pclk" and "hclk" aliases for the the macb
device so we can use the same clk handling paths for both AT91 and
AVR32.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
MII Kconfig option is apart of the core networking drivers and
by default NET_CORE is enabled so drivers selecting MII will
have MII enabled as well. It was found using the randconfig
option during testing, MII would be selected but NET_CORE
could be disabled. This caused a dependency error.
Resolved the dependency by selecting NET_CORE when MII is
selected.
Reported-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the Atmel driver into drivers/net/ethernet/cadence/ and
make the necessary Kconfig and Makefile changes.
CC: Nicolas Ferre <nicolas.ferre@atmel.com>
CC: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Jamie Iles